A General Energy Balance for Battery Systems
Open accessThe DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index; 2 of the 20 sources its claims cite were checked for support.
Abstract
A general energy balance for battery systems has been developed. This equation is useful for estimating cell thermal characteristics. Reliable predictions of cell temperature and heat‐generation rate are required for the design and thermal management of battery systems. The temperature of a cell changes as a result of electrochemical reactions, phase changes, mixing effects, and joule heating. The equation developed incorporates these effects in a complete and general manner. Simplifications and special cases are discussed. The results of applying the energy balance to a mathematical model of the cell discharged through two different reaction mechanisms are given as examples. The examples illustrate how the energy equation may be applied to a specific system to examine the relative contributions corresponding to the terms in the equation. The examples show that the processes involved in cell heat generation may be complex and that the application of a sufficiently general energy equation is advantageous.
Overview
CoChat Summary
TL;DR
The paper derives a general energy balance for battery systems that includes mixing, phase changes, and simultaneous electrochemical reactions with composition-dependent open-circuit potentials. It applies the equation to a modeled LiAl/LiCl-KCl/FeS cell discharged by two mechanisms and to a lead-acid estimate, showing that cell heat generation can be complex and that a sufficiently general energy equation is advantageous.
Key findings
- A general energy balance is developed that includes energy contributions from mixing, phase changes, and simultaneous electrochemical reactions with composition-dependent open-circuit potentials; prior treatments were restricted to single pure-phase reactants or a single reaction without mixing effects.
- For the LiAl/FeS model, adiabatic-reversible discharge gives the same temperature at 100% depth of discharge for both mechanisms because the overall reaction is the same; slope discontinuities occur at 50% and 12% utilization for mechanisms 1 and 2, respectively. In the realistic simulations, the second reaction begins at 30% and 11% utilization for mechanisms 1 and 2, respectively.
- The mixing term is negligible in the LiAl/FeS example; at 25% utilization, the temperature decline after current interruption is only about 0.2 K. For a lead-acid cell, the estimated temperature rise after full discharge is approximately 1.6 K, or 2.9 K if 1.25 mol of PbO2 is allowed for discharge.
- The sign of the mixing effect depends on the enthalpy curve: for lead-acid, the sulfuric acid-water enthalpy curve is concave upward, so a well-insulated cell heats after current interruption; for the high-temperature LiCl-KCl cell, the curve is concave downward, so the cell cools after interruption. Neglecting mixing overestimates lead-acid operating temperature and underestimates high-temperature cell operating temperature.
Methods
- The paper derives the energy balance from the first law of thermodynamics, assuming uniform battery temperature, and presents a final general equation including reaction, heat-capacity, phase-change, mixing, electrical-work, and heat-transfer terms.
- The equation is applied to an existing one-dimensional mathematical model of the LiAl/LiCl-KCl/FeS cell with a porous LiAl negative electrode, porous FeS positive electrode, electrolyte reservoir, and separator under galvanostatic discharge, using the two reaction mechanisms in Table I.
- Appendix A estimates the lead-acid temperature rise using an assumed uniform 5 molal sulfuric acid electrolyte, with one-third of the electrolyte in the cathode and anode spaces and one-third between the electrodes; the analysis compares adiabatic-reversible profiles with model simulations and examines the relative contributions of terms.
Limitations
- The paper states that the rigorous energy balance is difficult to apply without a detailed mathematical model because instantaneous composition profiles and current fractions are required; in practice, obtaining concentration profiles and predicting current partitioning among possible reactions is difficult.
- The paper states that the analysis does not include enthalpy changes from nonfaradaic reactions; self-discharge or corrosion must be divided into anodic and cathodic components and included as an additional term. The mixing term is also difficult because it involves integrations of concentration profiles.
- The paper states that actual FeS discharge is complicated and more like a mixture of the two proposed mechanisms plus simultaneously occurring chemical reactions; the examples are model simulations. The lead-acid estimate assumes artificial concentration jumps at interfaces, and diffusion would lower the estimate; nonuniform reaction distribution in porous electrodes would make the concentration distribution nonuniform. The breakdown is presented only up to 30% utilization because oscillatory behavior begins when the second reaction starts, to be treated in a subsequent publication.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
0 Valid · 5 Not valid · 12 Not checked · 75 Own results and interpretations
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“Basing the discharge on two Farādays (1 mol PbOg) and a transference number of 0.74 for hydrogen ion, we may calculate that the concentration in the cathode space and anode space drops to 1.04 and 2.79 molal, respectively (14).”
What the sources say
- Could not verifycites [14] 14. Hans Bode, "Lead-Acid Batteries," R. J. Brodd and K. V. Kordesch, Translators, Wiley-Interscience, New York (1977). sourceExperimental — accuracy not yet measured
The available text in the book-review passage (section labeled “Notice to Members April 1 is Cut-Off Date”; page not provided) describes the book’s theoretical treatment of lead-acid batteries but does not give this calculation. Searches for the 0.74 hydrogen-ion transference number, two Faradays, and the 1.04 and 2.79 molal concentrations found no passage addressing the claimed values. (LLM, conf=0.76)
hedgedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on 5 assumptions not shown here.
- Could not verify
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“The temperature rise, after full discharge, is approximately 1.6 K.”
- Also stated in: § Estimate of the Temperature Rise in a Lead-Acid Cell Following Current Interruption · p. 8 · hedged
“Using the data available in Ref. (14) (for 298 K), we calculate the temperature rise to be about 1.6 K”
What the sources say
- Could not verifycites [14] 14. Hans Bode, "Lead-Acid Batteries," R. J. Brodd and K. V. Kordesch, Translators, Wiley-Interscience, New York (1977). sourceExperimental — accuracy not yet measured
The available passages from the book review (page not provided) describe the book’s coverage of lead-acid battery thermodynamics but give no temperature rise after full discharge. Searches for “1.6 K” and the discharge-temperature claim found no supporting passage in our copy. (LLM, conf=0.75)
hedged- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on 5 assumptions not shown here.
- Also stated in: § Estimate of the Temperature Rise in a Lead-Acid Cell Following Current Interruption · p. 8 · hedged
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Although the mixing term offers a negligible contribution to the energy balance, it is interesting to investigate the processes that determine its behavior.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The profile for the X-phase mechanism in Fig. 1 follows the adiabatic-reversible profile up to about 5% utilization because the heat-loss contribution tends to cancel the polarization heat.”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“A general energy balance for battery systems has been developed.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on 3 assumptions not shown here.
39 more claims
Create a free account to see all 92 claims and every source verdict.
- It may state two separate claims as one. 20
- Probably not a substantial claim. 33
- The quote only partly states this claim. 1
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Conclusions · p. 8
“Equation [23], written for a single cell reaction, is the energy equation most commonly used in battery applications.”
§ Discussion of Terms · p. 5
“Furthermore, Eq. [24] is the form of the energy balance that is most commonly encountered in the literature.”
Citations
Cites
The publisher hasn’t deposited this paper’s reference list.
Research works printed but not linked: 12
- [1]1. J. M. Sherfey and A. Brenner, This Journal, 105, 665 (1958).
- [3]3. H. F. Gibbard, This Journal, 125, 353 (1978).
- [2]2. S. Gross, Energy Convers., 9, 55 (1969).
- [4]4. I. A. Dibrov and V. A. Bykov, Sov. Electrochem., 13, 298 (1977).
- [6]6. L. D. Hansen and R. M. Hart, This Journal, 125, 842 (1978).
- [5]5. I. A. Dibrov and V. A. Bykov, J. Appl. Chem., 49, 2025 (1977).
- [7]7. F. B. Tudron, ibid., 128, 516 (1981).
- [9]9. W. H. Tiedemann and J. Newman, in "Battery Design and Optimization," S. Gross, Editor, pp. 23-38, The Electrochemical Society Softbound Proceedings Series, Princeton, NJ (1979).
- [8]8. D. M. Chen and H. F. Gibbard, ibid., 130, 1975 (1983).
- [10]10. Richard Pollard and John Newman, This Journal, 128, 491 (1981).
- [11]11. Richard Pollard and John Newman, ibid., 128, 502 (1981).
- [13]13. Z. Tomczuk, S. K. Preto, and M. F. Roche, This Journal, 128, 760 (1981).
Cited by
Items 901–1,000 of 2,542
Wang, Q., Shen, J.-N., He, Y., & Ma, Z. (2020) · Chinese Physics B · doi:10.1088/1674-1056/ab90f8 · Cited by 24
Thermofluidic modeling and temperature monitoring of Li-ion battery energy storage system
Tao, F., Zhang, W., Guo, D., Cao, W., Sun, L., & Jiang, F. (2020) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2020.116026 · Cited by 25
Cheng, J., Shuai, S., Zhao, R., & Tang, Z. (2021) · Journal of Thermal Science and Engineering Applications · doi:10.1115/1.4053119 · Cited by 23
Mohsin, I. U., Schneider, L., Häringer, M., Ziebert, C., Rohde, M., Bauer, W., Ehrenberg, H., & Seifert, H. J. (2022) · Journal of Power Sources · doi:10.1016/j.jpowsour.2022.231901 · Cited by 26
“These temperature changes in the cell are because of electrochemical reactions, phase changes, mixing effects, and joule heating [18].”
BackgroundModel-Based Approach to Long Term Prediction of Battery Surface Temperature
Kumar, P., Rankin, G. W., Pattipati, K. R., et al. (2022) · IEEE Journal of Emerging and Selected Topics in Industrial Electronics · doi:10.1109/jestie.2022.3214060 · Cited by 24
“The updated heat generation equation is shown in (37) (see [44]).”
BackgroundThe electric-thermal coupling simulation and state estimation of lithium-ion battery
Xu, Z., Zhang, C., Sun, B., & Liu, S. (2022) · Journal of Energy Storage · doi:10.1016/j.est.2022.106431 · Cited by 25
Experimental Analysis of an Innovative Electrical Battery Thermal Management System
Cattani, L., Malavasi, M., Bozzoli, F., D’Alessandro, V., & Giammichele, L. (2023) · Energies · doi:10.3390/en16135071 · Cited by 24
Zhang, Y., Zhang, E., Guo, Z., et al. (2023) · Applied Energy · doi:10.1016/j.apenergy.2023.121480 · Cited by 24
Zhu, W., Lei, F., Zhong, H., Liu, J., & Ding, F. (2023) · Journal of Energy Storage · doi:10.1016/j.est.2023.108330 · Cited by 25
Ma, Y., Liu, Y., Ding, H., & Yu, X. (2023) · ISA Transactions · doi:10.1016/j.isatra.2023.09.026 · Cited by 25
Mendoza, S., Rothenberger, M. J., Hake, A. E., et al. (2016) · Journal of Power Sources · doi:10.1016/j.jpowsour.2016.01.059 · Cited by 24
Rheinfeld, A., Kosch, S., Erhard, S. V., Osswald, P. J., Rieger, B., & Jossen, A. (2016) · Journal of The Electrochemical Society · doi:10.1149/2.0701614jes · Cited by 26
Comprehensive Analysis on Dynamic Heat Generation of LiNi1/3Co1/3Mn1/3O2 Coin Cell under Overcharge
Chen, L., Jiang, L., Ye, S., Sun, J., & Wang, Q. (2019) · Journal of The Electrochemical Society · doi:10.1149/2.0861914jes · Cited by 25
Lin, Y., Xu, X., Wang, F., et al. (2020) · International Journal of Energy Research · doi:10.1002/er.5166 · Cited by 24
Research on Optimization of Charging Strategy Control for Aged Batteries
Sun, J., Ma, Q., Tang, C., Wang, T., Jiang, T., & Tang, Y. (2020) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2020.3003311 · Cited by 24
“In our previous study [16], a battery temperature calculation method based on the Bernardi heating model [17] was proposed, which can be written as:”
MethodA Review of MHP Technology and Its Research Status in Cooling of Li-Ion Power Battery and PEMFC
Li, Y., Chang, G., Xu, Y., Zhang, J., & Zhao, W. (2020) · Energy & Fuels · doi:10.1021/acs.energyfuels.0c02661 · Cited by 24
Moosavi, A., Ljung, A., & Lundström, T. S. (2021) · Journal of Energy Storage · doi:10.1016/j.est.2021.102525 · Cited by 24
Macroscopic Modeling of Polymer-Electrolyte Membranes
Weber, A. Z., & Newman, J. (2007) · Advances in fuel cells · doi:10.1016/s1752-301x(07)80007-x · Cited by 28
Self-citationPractical thermodynamic quantities for aqueous vanadium- and iron-based flow batteries
Hudak, N. S. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2013.12.089 · Cited by 24
Design and testing of a fuel-cell powered battery charging station
Jiang, Z. (2003) · Journal of Power Sources · doi:10.1016/s0378-7753(02)00725-5 · Cited by 25
“The change of the battery temperature is characterized by the thermal energy balance [14] equation that is described by Eq.”
MethodNiu, Y., Liu, Y., Zhou, T., Guo, C., Wu, G., Lv, W., Heydari, A., Peng, B., Xu, C., & Xu, Q. (2024) · Green Energy & Environment · doi:10.1016/j.gee.2024.04.005 · Cited by 29
Xiao, J., Min, H., Jiang, H., Zhang, Z., Sun, W., & Cao, Q. (2025) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2025.126721 · Cited by 25
Luo, Y., Zhu, C., Zang, M., et al. (2025) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2025.127332 · Cited by 23
Liu, Z., Zhang, X., & Qi, N. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.118264 · Cited by 23
Thermal performance enhancement of blade battery packs via multi-branch-converging channel design
Yang, X., Zhong, X., Su, C., Chen, K., & Xie, J. (2026) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2026.128330 · Cited by 26
Xie, Y., He, X.-J., Li, W., Zhang, Y., Dan, D., Lee, K., & Liu, J. (2020) · International Journal of Energy Research · doi:10.1002/er.5803 · Cited by 23
Wang, C., Cao, F., Li, M., Yin, X., Song, Y., & He, Y. (2021) · Chinese Science Bulletin (Chinese Version) · doi:10.1360/tb-2021-0648 · Cited by 21
Analysis and Improvement Measures of Driving Range Attenuation of Electric Vehicles in Winter
Mao, S., Han, M., Han, X., Jie, S., Lu, Y., Lu, L., & Ouyang, M. (2021) · World Electric Vehicle Journal · doi:10.3390/wevj12040239 · Cited by 23
“Calculation of the Battery Heat Generation Reference [22] simplified the heat production model, which is widely used to model the heat generation of battery systems.”
MethodFang-yuan, L., Ibrahim, M., Saeed, T., El-Refaey, A. M., Fagiry, M. A., & Elkhader, B. A. (2022) · Journal of Energy Storage · doi:10.1016/j.est.2022.104117 · Cited by 23
RetractedZeng, X., Men, Z., Deng, F., & Chen, C. (2022) · Materials · doi:10.3390/ma15113835 · Cited by 22
Bashiri, A. H., Sangtarash, A., & Zamāni, M. (2022) · Thermal Science and Engineering Progress · doi:10.1016/j.tsep.2022.101427 · Cited by 22
Arrhenius Equation-Based Model to Predict Lithium-Ions Batteries’ Performance
Zeng, L., Hu, Y., Lu, C., Pan, G., & Li, M. (2022) · Journal of Marine Science and Engineering · doi:10.3390/jmse10101553 · Cited by 25
“first established the general thermal model [11] of the battery system based on energy balance.”
BackgroundLiu, X., Zhang, C., Zhou, J.-G., et al. (2022) · Energy Reports · doi:10.1016/j.egyr.2022.11.003 · Cited by 23
Simulation Study on Heat Generation Characteristics of Lithium-Ion Battery Aging Process
Huang, R. N., Xu, Y., Wu, Q., Chen, J., Chen, F., & Yu, X. (2023) · Electronics · doi:10.3390/electronics12061444 · Cited by 26
Jiang, G., Wen, H., & Peng, C. (2024) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2024.123686 · Cited by 23
Model-based fault detection of hybrid fuel cell and photovoltaic direct current power sources
Zhang, L., & Huang, A. Q. (2011) · Journal of Power Sources · doi:10.1016/j.jpowsour.2011.01.089 · Cited by 23
Thermally coupled moving boundary model for charge–discharge of LiFePO4/C cells
Khandelwal, A., Hariharan, K. S., Gambhire, P., Kolake, S. M., Yeo, T., & Doo, S. (2015) · Journal of Power Sources · doi:10.1016/j.jpowsour.2015.01.018 · Cited by 24
Mohammadian, S. K., & Zhang, Y. (2016) · ASME Journal of Heat and Mass Transfer · doi:10.1115/1.4033811 · Cited by 26
“[12] is the most commonly used expression.”
Samad, N. A., Wang, B., Siegel, J. B., & Stefanopoulou, A. G. (2017) · Journal of Dynamic Systems Measurement and Control · doi:10.1115/1.4035742 · Cited by 23
“[2] proposed a general energy balance for batteries to predict the temperature.”
BackgroundActive Thermal Control of a Battery Pack Under Elevated Temperatures
Gao, X., Ma, Y., & Chen, H. (2018) · IFAC-PapersOnLine · doi:10.1016/j.ifacol.2018.10.047 · Cited by 23
Millet, L., Berrueta, A., Bruch, M., et al. (2019) · Applied Physics Reviews · doi:10.1063/1.5049665 · Cited by 23
Heat dissipation in a lithium ion cell
Vaidyanathan, H., Kelly, W. H., & Rao, G. M. (2001) · Journal of Power Sources · doi:10.1016/s0378-7753(00)00550-4 · Cited by 26
Xiong, R., Zhao, Z., Chen, C., Li, X., & Shen, W. (2024) · Chinese Journal of Mechanical Engineering · doi:10.1186/s10033-024-01024-6 · Cited by 23
“And its relationship with the SOC is shown in Figure 5 [26].”
BackgroundOptimization study of a Z-type airflow cooling system of a lithium-ion battery pack
Argade, S., & De, A. (2024) · Physics of Fluids · doi:10.1063/5.0212606 · Cited by 22
Zhang, B., Li, Y., Chen, Z., et al. (2024) · International Journal of Thermal Sciences · doi:10.1016/j.ijthermalsci.2024.109329 · Cited by 22
A Battery Thermal Management System Integrating Immersion Preheating and Immersion Cooling
Luo, Y., Zhou, D., Zou, Z., et al. (2024) · ACS Omega · doi:10.1021/acsomega.4c05163 · Cited by 22
Improve immersion cooling of cylindrical batteries in channel flows using the Tesla valve principle
Ye, J., Huang, J., Xia, Y., & Li, R. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.115546 · Cited by 22
Yi, F., Gan, Y., & Li, R. H. (2025) · Energy · doi:10.1016/j.energy.2025.135477 · Cited by 28
Yaw, C. T., Rajamony, R. K., Bhutto, Y. A., Bakthavatchalam, B., Kottala, R. K., Chopra, K., Paw, J. K. S., Doroody, C., Allasi, H. L., & Soudagar, M. E. M. (2025) · Results in Engineering · doi:10.1016/j.rineng.2025.105749 · Cited by 33
A high-fidelity online monitoring algorithm for multiple physical fields in battery pack
Xie, Y., Ma, W., Jiang, D., Li, W., Yang, R., Panchal, S., Fowler, M. W., & Zhang, Y. (2025) · Applied Energy · doi:10.1016/j.apenergy.2025.126443 · Cited by 27
Entropy change characteristics of LiMn0.67Fe0.33PO4 and Li4Ti5O12 electrode materials
Jalkanen, K., & Vuorilehto, K. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2014.09.091 · Cited by 22
Tang, S., Wang, Z., Guo, H., Wang, J., Li, X., & Yan, G. (2020) · Electrochimica Acta · doi:10.1016/j.electacta.2020.137465 · Cited by 25
Sheng, L., Zhang, Z., Su, L., Zhang, H., Zhang, H., Li, K., Fang, Y., & Ye, W. (2021) · Journal of Energy Storage · doi:10.1016/j.est.2021.102313 · Cited by 26
Jones, C. M., Li, B., & Tomar, V. (2021) · eTransportation · doi:10.1016/j.etran.2021.100109 · Cited by 22
Bedürftig, B., Oldenburger, M., Hüfner, T., et al. (2021) · Journal of Power Sources · doi:10.1016/j.jpowsour.2021.230110 · Cited by 22
“For electrochemical processes, the generated reversible heat can be expressed as a rate by [22]”
BackgroundYu, H., Yang, L., Zhang, L., Li, J., & Liu, X. (2022) · iScience · doi:10.1016/j.isci.2022.104243 · Cited by 21
“For the heat generation process, Bernardi et al. (1985) proposed a universal thermal model based on thermodynamic energy balance, which had been used in almost all studies of battery heat generation.”
MethodYang, L., Xu, H., Zhang, H., Chen, Y., Liu, M., & Tian, C. (2022) · Journal of Thermal Science · doi:10.1007/s11630-022-1604-y · Cited by 21
“According to the theory proposed by Bernardi [26], the heat generation rate of the battery is calculated as follows:”
MethodHai, T., Saïd, N. M., Cheraghian, G., Zhou, J., Malekshah, E. H., & Sharifpur, M. (2022) · Journal of Power Sources · doi:10.1016/j.jpowsour.2022.232222 · Cited by 22
RetractedQin, B., Zarrabeitia, M., Hoefling, A., Jusys, Z., Liu, X., Tübke, J., Behm, R. J., Cui, G., Varzi, A., & Passerini, S. (2023) · Journal of Power Sources · doi:10.1016/j.jpowsour.2023.232630 · Cited by 22
“The recorded, total heat generation rate ( Q ˙ tot ) can be described by the simplified energy balance model developed by New-man and coworkers that proved to be valid for insertion materials [15, 16]: [12].”
BackgroundYin, X., & Zhang, D. (2023) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/acbfe4 · Cited by 25
He, Y.-B., Wang, B.-C., Deng, H.-P., et al. (2023) · Journal of Energy Storage · doi:10.1016/j.est.2023.109604 · Cited by 22
Li, J., Li, P., Wang, M., Chen, C., Gao, Y., Yan, L.-Y., Yang, S.-C., Zhao, C. X., Chen, M.-M., Zhang, J., et al. (2023) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2023.122235 · Cited by 23
Ghasemi, S., Khoshvaght-Aliabadi, M., Asadollahzadeh, M. J., et al. (2024) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2024.125701 · Cited by 22
Pu, J. H., Li, R. C., Li, Y., et al. (2024) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2024.124330 · Cited by 22
Chen, Y., Liu, X., Yang, G., & Geng, H. (2017) · Annual Conference of the IEEE Industrial Electronics Society (IECON) · doi:10.1109/iecon.2017.8217337 · Cited by 23
Modeling Water Management in Polymer-Electrolyte Fuel Cells
Weber, A. Z., Balliet, R. J., Gunterman, H. P., & Newman, J. (2008) · Modern aspects of electrochemistry · doi:10.1007/978-0-387-49582-8_7 · Cited by 28
Self-citationAnalytical assessment of the thermal behavior of nickel–metal hydride batteries during fast charging
Taheri, P., Yazdanpour, M., & Bahrami, M. (2013) · Journal of Power Sources · doi:10.1016/j.jpowsour.2013.06.086 · Cited by 22
A circuit-based approach for electro-thermal modeling of lithium-ion batteries
Yazdanpour, M., Taheri, P., Mansouri, A., & Schweitzer, B. (2016) · Annual IEEE Semiconductor Thermal Measurement and Management Symposium/Proceedings · doi:10.1109/semi-therm.2016.7458455 · Cited by 22
“The electrochemical heat in each electrode is calculated from (23) ġec = Icell Vcell (V”
BackgroundMethodWu, J., Zhang, X., Chen, H., et al. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2024.111543 · Cited by 21
Liu, H., Xie, J., & Ma, X. (2024) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2024.123402 · Cited by 21
Kumar, A., Senapati, J. R., & Acharya, S. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.115464 · Cited by 21
Compact thermal management for high-density lithium-ion batteries: Liquid cooling solutions
Yuan, X., Zheng, R., Yang, J., et al. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.115523 · Cited by 21
Lai, Y., Ding, J., & Liu, L. (2025) · International Journal of Thermal Sciences · doi:10.1016/j.ijthermalsci.2025.110094 · Cited by 21
Rana, S., Kumar, R., & Bharj, R. S. (2025) · International Journal of Thermal Sciences · doi:10.1016/j.ijthermalsci.2025.110311 · Cited by 22
Heubner, C., Schneider, M., & Michaelis, A. (2017) · Journal of Solid State Electrochemistry · doi:10.1007/s10008-017-3828-4 · Cited by 21
A Novel Electro-Thermal Model of Lithium-Ion Batteries Using Power as the Input
Huang, B., Hu, M., Chen, L., Jin, G., Liao, S., Fu, C., Wang, D., & Cao, K. (2021) · Electronics · doi:10.3390/electronics10222753 · Cited by 23
“For example, the numerical calculation method [15,16] was put forward to generally estimate the temperature distribution of single cells or even entire battery packs, but it was inapplicable in online estimation due to its high computational cost; the electrochemical impedance spectroscopy (EIS) measurement-based meth…”
MethodQin, P., Wang, S., Cheng, Y., Jiang, L., Duan, Q., Jin, K., Sun, J., & Wang, Q. (2022) · Journal of Power Sources · doi:10.1016/j.jpowsour.2022.231731 · Cited by 21
Lin, Z., Wu, D., Du, C., et al. (2022) · Energy Reports · doi:10.1016/j.egyr.2022.10.109 · Cited by 21
Wassiliadis, N., Ank, M., Bach, A., Wanzel, M., Zollner, A.-S., Gamra, K. A., & Lienkamp, M. (2022) · Journal of Energy Storage · doi:10.1016/j.est.2022.105951 · Cited by 21
Yang, J., Yu, Y., Chen, S., Luo, M., Wu, Y., & Zhou, Z. (2023) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2023.124669 · Cited by 23
Shah, K., & Jain, A. (2014) · International Journal of Energy Research · doi:10.1002/er.3274 · Cited by 21
“[10,11].”
BackgroundState-of-charge estimation for lithium-ion batteries via a coupled thermal-electrochemical model
Tang, S., Wang, Y., Şahinoğlu, Z., Wada, T., Hara, S., & Krstić, M. (2015) · Proceedings of the ... American Control Conference/Proceedings of the American Control Conference · doi:10.1109/acc.2015.7172260 · Cited by 27
“However, electrochemical and chemical processes inside the battery cell during charging/discharging have their impacts on the thermal behavior [9], [10].”
BackgroundYu, G., Zhang, X., Wang, C., et al. (2013) · Journal of The Electrochemical Society · doi:10.1149/2.041311jes · Cited by 21
Huang, W., Zhang, W., Chen, A., Zhang, Y., & Li, M. (2019) · IEEE Access · doi:10.1109/access.2019.2958940 · Cited by 21
“[22] rationally simplified the heat generation mechanism of battery, obtained a simplified equation.”
BackgroundApproach to determine the entropy coefficient of a battery by numerical optimization
Lenz, M., Hoehl, T., Zanger, L., & Pischinger, S. (2020) · Journal of Power Sources · doi:10.1016/j.jpowsour.2020.228841 · Cited by 20
Anode Potential Estimation in Lithium-Ion Batteries Using Data-Driven Models for Online Applications
Hamar, J. C., Erhard, S. V., Zoerr, C., & Jossen, A. (2021) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/abe721 · Cited by 24
A Model Order Reduction Method for the Temperature Estimation in a Cylindrical Li-Ion Battery Cell
Muratori, M., Ma, N., Canova, M., et al. (2010) · Proceedings of the ASME Dynamic Systems and Control Conference · doi:10.1115/dscc2010-4200 · Cited by 21
Özdemir, T., Ekici, Ö., & Köksal, M. (2023) · Journal of Energy Storage · doi:10.1016/j.est.2023.109880 · Cited by 28
Kaewchoothong, N., Nuntadusit, C., Gonsrang, S., et al. (2024) · Heat Transfer Engineering · doi:10.1080/01457632.2024.2337977 · Cited by 20
“…generation rate ( _ q gen ) of actual Li-ion batteries during charge and discharge operations for this simulation, suggested by Bernardi et al. [45], was evaluated by where _ q ir is the irreversible heat, _ q re is the reversible heat, I is the current, U ca and U an are the open circuit…”
Wei, Y., Li, K., Liu, Z., Xie, Y., Song, Z., & Yue, H. (2024) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2024.124153 · Cited by 20
Review and analysis of thermal management for proton exchange membrane fuel cell hybrid power system
Zhang, X., Ma, X., Zhang, Z., Du, H., Wu, Z., Li, Z., & Shuai, S. (2025) · Renewable Energy · doi:10.1016/j.renene.2025.122716 · Cited by 23
Ren, F., Cui, N., Dong, L., & Li, C. (2025) · Energy · doi:10.1016/j.energy.2025.135504 · Cited by 22
Birinci, S., Albayrak, M., Sarper, B., Yazıcı, M. Y., Saglam, M., & Aydın, O. (2025) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2025.127708 · Cited by 21
Simulation of Temperature Field of Lithium Battery Pack Based on Computational Fluid Dynamics
Wang, Z., Fan, W., & Liu, P. (2017) · Energy Procedia · doi:10.1016/j.egypro.2017.03.764 · Cited by 20
A distributed multiple-heat source staged heating method in an electric vehicle
Ding, P., Wang, Z., Wang, Y., & Li, K. (2019) · Renewable Energy · doi:10.1016/j.renene.2019.11.099 · Cited by 20
Physics-based models in PV-battery hybrid power systems: Thermal management and degradation analysis
Bonkile, M. P., & Ramadesigan, V. (2020) · Journal of Energy Storage · doi:10.1016/j.est.2020.101458 · Cited by 23
Alsarraf, J., Alnaqi, A. A., & Al‐Rashed, A. A. A. A. (2022) · Journal of Energy Storage · doi:10.1016/j.est.2022.103998 · Cited by 23
White, G., Hales, A., Patel, Y., et al. (2022) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2022.118573 · Cited by 20
Thermal behavior analysis of lithium-ion capacitors at transient high discharge rates
Zhou, W., Liu, Z., An, Y., Luo, M., Zhang, X., Song, S., Li, C., Liu, Z., Gao, Y., Zhang, H., et al. (2022) · Journal of Energy Storage · doi:10.1016/j.est.2022.105208 · Cited by 22
Zhu, W., Lei, F., Zhong, H., & Wang, D. (2023) · Energy · doi:10.1016/j.energy.2023.127424 · Cited by 20
Metadata
- Authors
- Bernardi, D., Pawlikowski, E., & Newman, J.
- Affiliations
- University of California, Berkeley (US)
- ORCID
- Newman, J.
- Venue
- Journal of The Electrochemical Society
- Publisher
- The Electrochemical Society
- Published
- 1985-01-01
- Volume
- 132
- Issue
- 1
- Pages
- 5-12
- ISSN
- 0013-4651 (ISSN-L)
- 1945-7111
- OpenAlex
- W2023385933
- Cited by
- 2,548
- References
- 0
- Citations by year
- 2026: 383 · 2025: 387 · 2024: 339 · 2023: 265 · 2022: 238 · 2021: 167 · 2020: 147 · 2019: 106 · 2018: 74 · 2017: 89 · 2016: 42 · 2015: 53 · 2014: 75 · 2013: 51 · 2012: 31
- FWCI
- 0.00
- Type
- journal article
- Language
- en
- Open access
- bronze
- doi.org
- Licence
- iopscience.iop.org/page/copyright (vor, 12758 d)
- iopscience.iop.org/info/page/text-and-data-mining (tdm, 12758 d)
- Locations
- Journal of The Electrochemical Society (publishedVersion)
- Topics
- Physical Sciences › Engineering › Automotive Engineering › Battery Modeling and Management
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Advancements in Battery Materials
- Physical Sciences › Chemistry › Electrochemistry › Molten salt chemistry and electrochemical processes
- Keywords
- heat generation rate, Joule heating, phase transitions, mixing effects, electrochemical reactions, battery thermal management, battery modeling
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.