A General Energy Balance for Battery Systems
Open accessThe DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index; 2 of the 20 sources its claims cite were checked for support.
Abstract
A general energy balance for battery systems has been developed. This equation is useful for estimating cell thermal characteristics. Reliable predictions of cell temperature and heat‐generation rate are required for the design and thermal management of battery systems. The temperature of a cell changes as a result of electrochemical reactions, phase changes, mixing effects, and joule heating. The equation developed incorporates these effects in a complete and general manner. Simplifications and special cases are discussed. The results of applying the energy balance to a mathematical model of the cell discharged through two different reaction mechanisms are given as examples. The examples illustrate how the energy equation may be applied to a specific system to examine the relative contributions corresponding to the terms in the equation. The examples show that the processes involved in cell heat generation may be complex and that the application of a sufficiently general energy equation is advantageous.
Overview
CoChat Summary
TL;DR
The paper derives a general energy balance for battery systems that includes mixing, phase changes, and simultaneous electrochemical reactions with composition-dependent open-circuit potentials. It applies the equation to a modeled LiAl/LiCl-KCl/FeS cell discharged by two mechanisms and to a lead-acid estimate, showing that cell heat generation can be complex and that a sufficiently general energy equation is advantageous.
Key findings
- A general energy balance is developed that includes energy contributions from mixing, phase changes, and simultaneous electrochemical reactions with composition-dependent open-circuit potentials; prior treatments were restricted to single pure-phase reactants or a single reaction without mixing effects.
- For the LiAl/FeS model, adiabatic-reversible discharge gives the same temperature at 100% depth of discharge for both mechanisms because the overall reaction is the same; slope discontinuities occur at 50% and 12% utilization for mechanisms 1 and 2, respectively. In the realistic simulations, the second reaction begins at 30% and 11% utilization for mechanisms 1 and 2, respectively.
- The mixing term is negligible in the LiAl/FeS example; at 25% utilization, the temperature decline after current interruption is only about 0.2 K. For a lead-acid cell, the estimated temperature rise after full discharge is approximately 1.6 K, or 2.9 K if 1.25 mol of PbO2 is allowed for discharge.
- The sign of the mixing effect depends on the enthalpy curve: for lead-acid, the sulfuric acid-water enthalpy curve is concave upward, so a well-insulated cell heats after current interruption; for the high-temperature LiCl-KCl cell, the curve is concave downward, so the cell cools after interruption. Neglecting mixing overestimates lead-acid operating temperature and underestimates high-temperature cell operating temperature.
Methods
- The paper derives the energy balance from the first law of thermodynamics, assuming uniform battery temperature, and presents a final general equation including reaction, heat-capacity, phase-change, mixing, electrical-work, and heat-transfer terms.
- The equation is applied to an existing one-dimensional mathematical model of the LiAl/LiCl-KCl/FeS cell with a porous LiAl negative electrode, porous FeS positive electrode, electrolyte reservoir, and separator under galvanostatic discharge, using the two reaction mechanisms in Table I.
- Appendix A estimates the lead-acid temperature rise using an assumed uniform 5 molal sulfuric acid electrolyte, with one-third of the electrolyte in the cathode and anode spaces and one-third between the electrodes; the analysis compares adiabatic-reversible profiles with model simulations and examines the relative contributions of terms.
Limitations
- The paper states that the rigorous energy balance is difficult to apply without a detailed mathematical model because instantaneous composition profiles and current fractions are required; in practice, obtaining concentration profiles and predicting current partitioning among possible reactions is difficult.
- The paper states that the analysis does not include enthalpy changes from nonfaradaic reactions; self-discharge or corrosion must be divided into anodic and cathodic components and included as an additional term. The mixing term is also difficult because it involves integrations of concentration profiles.
- The paper states that actual FeS discharge is complicated and more like a mixture of the two proposed mechanisms plus simultaneously occurring chemical reactions; the examples are model simulations. The lead-acid estimate assumes artificial concentration jumps at interfaces, and diffusion would lower the estimate; nonuniform reaction distribution in porous electrodes would make the concentration distribution nonuniform. The breakdown is presented only up to 30% utilization because oscillatory behavior begins when the second reaction starts, to be treated in a subsequent publication.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
0 Valid · 5 Not valid · 12 Not checked · 75 Own results and interpretations
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“Basing the discharge on two Farādays (1 mol PbOg) and a transference number of 0.74 for hydrogen ion, we may calculate that the concentration in the cathode space and anode space drops to 1.04 and 2.79 molal, respectively (14).”
What the sources say
- Could not verifycites [14] 14. Hans Bode, "Lead-Acid Batteries," R. J. Brodd and K. V. Kordesch, Translators, Wiley-Interscience, New York (1977). sourceExperimental — accuracy not yet measured
The available text in the book-review passage (section labeled “Notice to Members April 1 is Cut-Off Date”; page not provided) describes the book’s theoretical treatment of lead-acid batteries but does not give this calculation. Searches for the 0.74 hydrogen-ion transference number, two Faradays, and the 1.04 and 2.79 molal concentrations found no passage addressing the claimed values. (LLM, conf=0.76)
hedgedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on 5 assumptions not shown here.
- Could not verify
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“The temperature rise, after full discharge, is approximately 1.6 K.”
- Also stated in: § Estimate of the Temperature Rise in a Lead-Acid Cell Following Current Interruption · p. 8 · hedged
“Using the data available in Ref. (14) (for 298 K), we calculate the temperature rise to be about 1.6 K”
What the sources say
- Could not verifycites [14] 14. Hans Bode, "Lead-Acid Batteries," R. J. Brodd and K. V. Kordesch, Translators, Wiley-Interscience, New York (1977). sourceExperimental — accuracy not yet measured
The available passages from the book review (page not provided) describe the book’s coverage of lead-acid battery thermodynamics but give no temperature rise after full discharge. Searches for “1.6 K” and the discharge-temperature claim found no supporting passage in our copy. (LLM, conf=0.75)
hedged- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on 5 assumptions not shown here.
- Also stated in: § Estimate of the Temperature Rise in a Lead-Acid Cell Following Current Interruption · p. 8 · hedged
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Although the mixing term offers a negligible contribution to the energy balance, it is interesting to investigate the processes that determine its behavior.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The profile for the X-phase mechanism in Fig. 1 follows the adiabatic-reversible profile up to about 5% utilization because the heat-loss contribution tends to cancel the polarization heat.”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“A general energy balance for battery systems has been developed.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on 3 assumptions not shown here.
39 more claims
Create a free account to see all 92 claims and every source verdict.
- It may state two separate claims as one. 20
- Probably not a substantial claim. 33
- The quote only partly states this claim. 1
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Conclusions · p. 8
“Equation [23], written for a single cell reaction, is the energy equation most commonly used in battery applications.”
§ Discussion of Terms · p. 5
“Furthermore, Eq. [24] is the form of the energy balance that is most commonly encountered in the literature.”
Citations
Cites
The publisher hasn’t deposited this paper’s reference list.
Research works printed but not linked: 12
- [1]1. J. M. Sherfey and A. Brenner, This Journal, 105, 665 (1958).
- [3]3. H. F. Gibbard, This Journal, 125, 353 (1978).
- [2]2. S. Gross, Energy Convers., 9, 55 (1969).
- [4]4. I. A. Dibrov and V. A. Bykov, Sov. Electrochem., 13, 298 (1977).
- [6]6. L. D. Hansen and R. M. Hart, This Journal, 125, 842 (1978).
- [5]5. I. A. Dibrov and V. A. Bykov, J. Appl. Chem., 49, 2025 (1977).
- [7]7. F. B. Tudron, ibid., 128, 516 (1981).
- [9]9. W. H. Tiedemann and J. Newman, in "Battery Design and Optimization," S. Gross, Editor, pp. 23-38, The Electrochemical Society Softbound Proceedings Series, Princeton, NJ (1979).
- [8]8. D. M. Chen and H. F. Gibbard, ibid., 130, 1975 (1983).
- [10]10. Richard Pollard and John Newman, This Journal, 128, 491 (1981).
- [11]11. Richard Pollard and John Newman, ibid., 128, 502 (1981).
- [13]13. Z. Tomczuk, S. K. Preto, and M. F. Roche, This Journal, 128, 760 (1981).
Cited by
Items 701–800 of 2,542
Xu, Q., Xie, Y., Li, X., et al. (2024) · Energy · doi:10.1016/j.energy.2024.132847 · Cited by 36
Review of integrated thermal management system research for battery electrical vehicles
Zhu, Z., Zhang, Y., Chen, A., Chen, J., Wu, Y., Wang, X., & Fei, T. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2024.114662 · Cited by 45
A review of power battery cooling technologies
Wang, C., Liu, Q., Wang, Z., & Cheng, X. (2025) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2025.115494 · Cited by 37
Effect of immersion cooling design optimization on thermal management for lithium battery module
Song, Y., Wang, Z., Jia, D., Yuan, D., Yi, C., Zheng, X., & Zhang, S. (2025) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2025.126401 · Cited by 38
Zhou, L., Xie, L. H., Dai, J., Jain, A., Chen, G., & Zhao, Y. (2025) · Asia-Pacific Journal of Chemical Engineering · doi:10.1002/apj.70056 · Cited by 41
Swierczynski, M. J., Stroe, D., Stanciu, T., & Kær, S. K. (2016) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2016.09.109 · Cited by 40
“Thermal behaviour of the li-ion batteries has been studied in a number of publications (Bernardi et al., 1985; Doyle et al., 1993).”
BackgroundAnalysis of nanofluid flow and heat transfer behavior of Li-ion battery modules
Sirikasemsuk, S., Naphon, N., Eiamsa-ard, S., & Naphon, P. (2023) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2023.124058 · Cited by 36
Ma, Y., Ma, Q., Ding, H., et al. (2023) · IEEE Transactions on Intelligent Transportation Systems · doi:10.1109/tits.2023.3337786 · Cited by 35
“Neglecting the phase change heat and side reaction heat, the heat production rate of the battery is calculated according to the Bernardi equation [27] Q where dU oc dT b is the entropy heat coefficient, which is the function of the battery SOC.”
MethodRecent progress on battery thermal management with composite phase change materials
Kumar, S. S., & Rao, G. A. P. (2024) · Energy Storage · doi:10.1002/est2.647 · Cited by 39
Lin, Y., Li, W., Deng, W., Sun, W., Huang, M., & Liu, Z. (2024) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2024.123852 · Cited by 35
Xiong, S., Wang, Z., Bao, R., et al. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2024.113529 · Cited by 35
Du, X., Wang, Z., Gao, Q., Yang, H., Bao, R., & Xiong, S. (2024) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2024.124384 · Cited by 36
Wang, C., Chen, Z., Yang, S., & Li, J. (2025) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2025.125938 · Cited by 39
Pal, R. K., Paw, J. K. S., Ganesan, P., & Tong, C. W. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.116011 · Cited by 43
Garttan, G., Alahakoon, S., Emami, K., & Jayasinghe, S. G. (2025) · Energies · doi:10.3390/en18154174 · Cited by 67
“Bernardi et al.’s [155] equation can be simplified to: where ˙ Q is the rate of heat generated or consumed, M is the mass per unit area of one cell, C m p means specific heat capacity at constant pressure in J/g-K, and T is absolute temperature in K. Equation (11) can be reformulated as follows:…”
Thermal behavior analysis of a pouch type Li[Ni 0.7 Co 0.15 Mn 0.15 ]O 2 ‐based lithium‐ion battery
Yun, F., Tang, L., Li, W., Jin, W., Pang, J., & Lu, S. (2015) · Rare Metals · doi:10.1007/s12598-015-0605-3 · Cited by 37
“[15] firstly proposed a general energy balance equation for a whole cell to express the heat generation rate (Q) in Watts which depends on the thermodynamic properties of”
BackgroundMethodModeling of separator failure in lithium-ion pouch cells under compression
Sarkar, A., Shrotriya, P., & Chandra, A. (2019) · Journal of Power Sources · doi:10.1016/j.jpowsour.2019.226756 · Cited by 35
Sturm, J., Ludwig, S., Zwirner, J., Ramirez-Garcia, C., Heinrich, B., Horsche, M. F., & Jossen, A. (2019) · Journal of Power Sources · doi:10.1016/j.jpowsour.2019.226834 · Cited by 35
“The reformulation and solving of the solid-di usion PDE in the OC-PCM instead of using approximations contributes to the di erent cell voltages compared to the PP- and EM-PCM.”
MethodResultInfluentialThermal performance prediction of the battery surface via dynamic mode decomposition
Kanbur, B. B., Kumtepeli, V., & Duan, F. (2020) · Energy · doi:10.1016/j.energy.2020.117642 · Cited by 37
An energy balance evaluation in lithium-ion battery module under high temperature operation
Gozdur, R., Guzowski, B., Dimitrova, Z., Noury, A., Mitukiewicz, G., & Batory, D. (2020) · Energy Conversion and Management · doi:10.1016/j.enconman.2020.113565 · Cited by 38
Bulut, E., Albak, E. İ., Sevi̇lgen, G., et al. (2022) · International Journal of Energy Research · doi:10.1002/er.7637 · Cited by 35
“…j ECh can be calculated by the expression of Newman and Tiedemann, 31 Tiedemann and Newman, 32 and _ q ECh is formulized in Equation (6) by Bernardi et al 33 as follows: where U and Y are the fitting parameters and the detailed information about these equations can be found in References 26,34.”
MethodTest Method for Thermal Characterization of Li-Ion Cells and Verification of Cooling Concepts
Christen, R., Rizzo, G., Gadola, A., & Stöck, M. (2017) · Batteries · doi:10.3390/batteries3010003 · Cited by 35
“Rather, the heat generated within the cell due to resistive losses and change in entropy have to be considered [7,8].”
BackgroundKhan, M. N., Dhahad, H. A., Alamri, S., Anqi, A. E. M., Sharma, K., Mehrez, S., Shamseldin, M. Α., & Ibrahim, B. F. (2022) · Journal of Energy Storage · doi:10.1016/j.est.2022.104573 · Cited by 47
RetractedLi, L., Zhou, X., Ju, X., Zhou, Z., Wang, B., Cao, B., & Yang, L. (2023) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2023.120172 · Cited by 33
Liu, Z., Cao, M. L., Li, J., et al. (2023) · Journal of Energy Storage · doi:10.1016/j.est.2023.110234 · Cited by 34
Li, Y., Bai, M., Zhou, Z., Wu, W., Wei, L., Hu, C., Liu, X., Gao, S. H., Li, Y., & Song, Y. (2024) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2024.124453 · Cited by 40
Kabirzadeh, P., Liu, Z., Olyaei, M., Qiu, H., Gurumukhi, Y., Tyagi, H., Jiang, Y., Garimella, V. S., Singh, B., Li, Y., et al. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.117289 · Cited by 47
Temperature characterization analysis of LiFePO4/C power battery during charging and discharging
Yang, K., An, J. J., & Chen, S. (2009) · Journal of Thermal Analysis and Calorimetry · doi:10.1007/s10973-009-0623-1 · Cited by 34
Numerical study of a novel battery thermal management system for a prismatic Li-ion battery module
Li, W., Zhuang, X., & Xu, X. (2019) · Energy Procedia · doi:10.1016/j.egypro.2019.01.771 · Cited by 35
Xie, Y., Wang, X., Li, W., Zhang, Y., Dan, D., Li, K., Feng, F., Wu, C., & Wang, P. (2020) · International Journal of Thermal Sciences · doi:10.1016/j.ijthermalsci.2020.106611 · Cited by 35
Yang, X., Gao, X., Zhang, F., Luo, W., & Duan, Y. (2021) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2021.116746 · Cited by 35
Xie, Y., Wang, X., Hu, X., et al. (2021) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2021.3102292 · Cited by 34
“[11] established the first comprehensive heat generation model for cells, but this model is not suitable for predicting the temperature evolution of cells due to its complex form.”
BackgroundOptimal Sensor Placement for Multifault Detection and Isolation in Lithium-Ion Battery Pack
Cheng, Y., D’Arpino, M., & Rizzoni, G. (2021) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2021.3137462 · Cited by 34
Effect of Passive Thermal Management System on the Eletrothermal Performance of Battery Module
Hu, S., Wang, S., Zhang, Y., Ma, C., Wu, S., & Li, L. (2021) · International Journal of Thermal Sciences · doi:10.1016/j.ijthermalsci.2022.107842 · Cited by 35
Effat, M. B., Wu, C., & Francesco Ciucci, A. (2016) · Asia-Pacific Journal of Chemical Engineering · doi:10.1002/apj.1999 · Cited by 38
A Lumped Electro-Thermal Model for Li-Ion Cells in Electric Vehicle Application
Makinejad, K., Arunachala, R., Arnold, S., Ennifar, H., Zhou, H., Jossen, A., & Changyun, W. (2015) · World Electric Vehicle Journal · doi:10.3390/wevj7010001 · Cited by 34
Numerical Simulations for Indirect and Direct Cooling of 54 V LiFePO4 Battery Pack
Li, Y., Zhou, Z., Su, L., Bai, M., Gao, L., Li, Y., Liu, X., Li, Y., & Song, Y. (2022) · Energies · doi:10.3390/en15134581 · Cited by 42
Qian, L., Yi, Y., Zhang, W., Fu, C., Xia, C., & Ma, T. (2023) · International Journal of Energy Research · doi:10.1155/2023/8571535 · Cited by 37
“With a large current rate ( ≥ 1C), the heat generation of the battery can be described as [45] where M , C p , T , U , and I represent the mass weight, heat The thermal stability of the battery material fades during the degradation process, and battery capacity also fades, which induces overcharge…”
Liu, M., Zhou, X., Yang, L., & Ju, X. (2023) · Journal of Energy Storage · doi:10.1016/j.est.2023.108241 · Cited by 33
Ma, Y., Ma, Q., Liu, Y., & Gao, J. (2023) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2023.3308127 · Cited by 34
“To fully describe the coupling relationship and simulate the dynamic characteristics of the battery, an electrothermal coupling model of the battery pack is established [21], [22], [31].”
MethodInvestigation of the thermal management potential of phase change material for lithium-ion battery
Wang, H., Guo, Y., Ren, Y., Yeboah, S. K., Wang, J., Long, F., Zhang, Z., & Jiang, R. (2023) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2023.121590 · Cited by 76
Du, X., Hu, Y., Song, M., Choi, C., Choe, S.-Y., Labaza, C., Gao, J., Koch, B. J., & Garrick, T. R. (2023) · Journal of Power Sources · doi:10.1016/j.jpowsour.2023.233688 · Cited by 35
Jia, Y., Brancato, L., Giglio, M., & Cadini, F. (2023) · Journal of Power Sources · doi:10.1016/j.jpowsour.2023.233874 · Cited by 42
Kang, Z., Peng, Q., Yin, R., Yao, Z., Song, Y., & He, B. (2024) · Energy · doi:10.1016/j.energy.2023.130164 · Cited by 33
Thakur, S. S., Akula, R., & Kumar, L. (2024) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2024.122555 · Cited by 31
Wang, R., Zhang, H., Chen, J., et al. (2024) · Energy Technology · doi:10.1002/ente.202301205 · Cited by 33
Li, Y., Jiang, C., Zhao, C., Zhu, D., Wang, L., Xie, H., & Yu, W. (2025) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2025.115706 · Cited by 41
Progression of battery storage technology considering safe and sustainable stationary application
Murarka, M., Purohit, P. R., Rakshit, D., & Verma, A. (2022) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2022.134279 · Cited by 41
Quantitative performance analysis of graphite-LiFePO4 battery working at low temperature
Bae, S., Song, H. D., Nam, I., Kim, G.-P., Lee, J. M., & Yi, J. (2014) · Chemical Engineering Science · doi:10.1016/j.ces.2014.07.042 · Cited by 32
“The diffusion coefficient and rate constant follow the Arrhenius equation and their value changes with temperature as (Bernardi et al., 1985).”
BackgroundRodríguez-Iturriaga, P., García, V. M., Rodríguez-Bolívar, S., Valdés, E. E., Anseán, D., & López-Villanueva, J. A. (2024) · Applied Energy · doi:10.1016/j.apenergy.2024.123327 · Cited by 34
Zhang, L., Xia, B., & Zhang, F. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2024.112067 · Cited by 38
Chen, Y., He, M., Feng, J., Wang, C., & Zhuang, Y. (2024) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2024.123586 · Cited by 32
Zare, P., Perera, N., Lahr, J., & Hasan, R. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2024.115054 · Cited by 35
Recent advancements in internal and external thermoregulation strategies for lithium-ion batteries
Marri, G. K., Ee, Y.-J., He, Z., & Ho, J. Y. (2025) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2025.116127 · Cited by 42
Optimizing the Heat Dissipation of an Electric Vehicle Battery Pack
Hwang, H.-Y., Chen, Y.-S., & Chen, J.-S. (2014) · Advances in Mechanical Engineering · doi:10.1155/2014/204131 · Cited by 33
“The heat generation rate of one unit cell [17] is shown in q = I (E − U) − I (TdE dT) , (1)”
BackgroundGiel, H., Henriques, D., Bourne, G., & Markus, T. (2018) · Journal of Power Sources · doi:10.1016/j.jpowsour.2018.04.017 · Cited by 33
Engbroks, L., Görke, D., Schmiedler, S., et al. (2018) · IFAC-PapersOnLine · doi:10.1016/j.ifacol.2018.10.078 · Cited by 32
Pan, C., Tang, Q., He, Z., Wang, L., & Chen, L. (2019) · Journal of Electrochemical Energy Conversion and Storage · doi:10.1115/1.4045197 · Cited by 31
Novel Z-Shaped Structure of Lithium-Ion Battery Packs and Optimization for Thermal Management
Xi, Y., Feng, Y., Xiao, Y., et al. (2019) · Journal of Energy Engineering · doi:10.1061/(asce)ey.1943-7897.0000635 · Cited by 32
Ibrahim, A., Guo, J. H., Wang, Y., Zheng, Y., Lei, B., & Jiang, F. (2020) · International Journal of Energy Research · doi:10.1002/er.5599 · Cited by 33
“Toward this end, a recent announcement by the Department of Energy in the United States has presented a target of a 30% reduction in the overall weight of electric vehicles.(46) It can be seen that even though most previously discussed studies investigate indirect liquid cooling, the majority do so by investigating co…”
BackgroundZhang, W., Liang, Z., Ling, G., & Huang, L. (2021) · Journal of Energy Storage · doi:10.1016/j.est.2021.102849 · Cited by 33
Thermal encapsulation of large battery packs for electric vehicles operating in cold climate
Babu, A. R., Minovski, B. B., & Sebben, S. (2022) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2022.118548 · Cited by 38
Yang, K., Li, Y., Yuan, J., et al. (2023) · Journal of Energy Storage · doi:10.1016/j.est.2023.106679 · Cited by 32
Han, U., Choi, H., Lee, H., & Lee, H. (2023) · International Journal of Energy Research · doi:10.1155/2023/9929496 · Cited by 40
“According to the Bernardi equation [6] with the assumption of negligible mixing and phase change e ff ects [7], the battery heat generation is primarily composed of two primary heat sources, the irreversible joule heat and reversible entropic heat.”
Thermal management for energy storage system for smart grid
Alaoui, C. (2017) · Journal of Energy Storage · doi:10.1016/j.est.2017.07.027 · Cited by 33
Huang, H., Zhou, Z.-F., Wu, W.-T., Wei, L., Li, Y., Lv, X.-C., Liu, X., Li, Y., & Song, Y.-C. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2023.110050 · Cited by 25
Tan, Y., Li, Y., Gu, Y., Liu, W., Fang, J., & Pan, C. (2023) · Energies · doi:10.3390/en17010178 · Cited by 35
Enhancing Battery Thermal Management With Virtual Temperature Sensor Using Hybrid CNN-LSTM
Bamati, S., Chaoui, H., & Gualous, H. (2024) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2024.3376515 · Cited by 40
Dong, C., & Sun, D. (2024) · Applied Energy · doi:10.1016/j.apenergy.2024.123248 · Cited by 39
Keyhani-Asl, A., Perera, N., Lahr, J., & Hasan, R. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2024.112306 · Cited by 32
“Bernardi Model [68] Electrical power, enthalpy of reaction, heat through mixing, material phase change - Baseline for heat generation understanding.”
Refined air-cooled battery sizing process for conceptual design of eVTOL aircraft
Park, J., Jeong, T., & Yee, K. (2024) · Applied Energy · doi:10.1016/j.apenergy.2024.124567 · Cited by 33
Cai, Y., Sun, Q. H., Gu, X., Li, Y., Luo, W., Zhang, Y., Zhang, B., Huang, G., & Dong, K. (2024) · Energy · doi:10.1016/j.energy.2024.133419 · Cited by 34
Wu, J., Peng, Q., & Wang, X. (2024) · Energy · doi:10.1016/j.energy.2024.134343 · Cited by 31
Esmaeili, Z., Vahidhosseini, S. M., Rashidi, S., et al. (2025) · International Journal of Thermal Sciences · doi:10.1016/j.ijthermalsci.2025.110194 · Cited by 31
Parameterization and Validation of a Distributed Coupled Electro-Thermal Model for Prismatic Cells
Samad, N. A., Siegel, J. B., & Stefanopoulou, A. G. (2014) · ASME Dynamic Systems and Control Conference (DSCC) · doi:10.1115/dscc2014-6321 · Cited by 30
“[2] proposed a general energy balance for batteries to predict temperature.”
BackgroundThermal behavior of full-scale battery pack based on comprehensive heat-generation model
Yoo, K., & Kim, J. (2019) · Journal of Power Sources · doi:10.1016/j.jpowsour.2019.226715 · Cited by 32
Thermal conductivity of V 2 O 5 nanowires and their contact thermal conductance
Wang, Q., Liang, X., Liu, B., et al. (2019) · Nanoscale · doi:10.1039/c9nr08803b · Cited by 30
Yang, X., Hu, X., Chen, Z., & Chen, Y. (2020) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2020.115634 · Cited by 34
Li, M., Liu, F., Han, B., Guo, J., & Xu, Y. (2021) · Ionics · doi:10.1007/s11581-021-04033-w · Cited by 32
“qgen is calculated by using the Bernardi equation, which defines the battery as a uniform heat source [35]:”
MethodImproving battery thermal behavior and consistency by optimizing structure and working parameter
Xie, Y., Guo, H., Li, W., et al. (2021) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2021.117281 · Cited by 31
Study on battery direct-cooling coupled with air conditioner novel system and control method
Gao, Y., Gao, Q., & Zhang, X. (2023) · Journal of Energy Storage · doi:10.1016/j.est.2023.108032 · Cited by 31
Xie, Y., Zheng, J., Li, W., Lee, K., Zhang, Y., Liu, J., Dan, D., Wu, C., & Wang, P. (2019) · International Journal of Energy Research · doi:10.1002/er.5058 · Cited by 32
Ham, S. H., Jang, D. S., Lee, M., Jang, Y., & Kim, Y. (2022) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2022.119790 · Cited by 30
Rojas, C., Oca, L., Lopetegi, I., Iraola, U., & Carrasco, J. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2023.110384 · Cited by 30
Zhang, W., Sun, Q., Zhou, X., Wu, L., & Hu, Y. (2024) · Energy · doi:10.1016/j.energy.2024.133053 · Cited by 33
Yogeshwar, D., Repaka, R., & Marath, N. K. (2024) · International Journal of Thermal Sciences · doi:10.1016/j.ijthermalsci.2024.109521 · Cited by 33
A review of thermal management systems for extreme fast charging Li-ion batteries
Fekri, Y., Heyhat, M. M., Salehzadeh, F. J., Wang, Z., & Rahbari, A. (2025) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2025.127870 · Cited by 37
Thermo-electrochemical evaluation of lithium-ion batteries for space applications
Walker, W. Q., Yayathi, S., Shaw, J., & Ardebili, H. (2015) · Journal of Power Sources · doi:10.1016/j.jpowsour.2015.08.054 · Cited by 32
Formula-E race strategy development using artificial neural networks and Monte Carlo tree search
Liu, X., & Fotouhi, A. (2020) · Neural Computing and Applications · doi:10.1007/s00521-020-04871-1 · Cited by 36
Schindler, M. W., Durdel, A., Sturm, J., et al. (2020) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/abad6b · Cited by 30
Experimental Assessment of the Lumped Lithium Ion Battery Model at Different Operating Conditions
Özdemir, T., Amini, A., Ekici, Ö., & Köksal, M. (2021) · Heat Transfer Engineering · doi:10.1080/01457632.2021.1874666 · Cited by 33
“composed of reversible and irreversible terms [2].”
Lagnoni, M., Nicolella, C., & Bertei, A. (2021) · Electrochimica Acta · doi:10.1016/j.electacta.2021.139098 · Cited by 34
Yang, Y., Chen, L., Tong, K., Yang, L., Jiang, K., Kong, Y., & Du, X. (2021) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2021.122309 · Cited by 31
A Comprehensive Study on Influence of Battery Thermal Behavior on Degradation and Consistency
Xie, Y., Yang, R., Li, W., et al. (2022) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2022.3148335 · Cited by 30
An, Z., Liu, H., Gao, W., et al. (2024) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2024.122421 · Cited by 30
Thermal modelling of new Li-ion cell design modifications
Sievers, M., Sievers, U., & Mao, S. S. (2010) · Forschung im Ingenieurwesen · doi:10.1007/s10010-010-0127-y · Cited by 30
“propose a formula since confirmed by Bernardi et al. [ 20 ]:”
A spatially-reduced dynamic model for the thermal characterisation of Li-ion battery cells
Muratori, M., Canova, M., & GUEZENNEC, Y. G. (2012) · International Journal of Vehicle Design · doi:10.1504/ijvd.2012.047402 · Cited by 30
Chin, C. S., Gao, Z., Chiew, J. H. K., & Zhang, C. (2018) · Energies · doi:10.3390/en11092467 · Cited by 33
“[69] with the total heat generated (Qgen) in the battery cell as defined by”
BackgroundMethodFang, G., Huang, Y., Yuan, W., et al. (2019) · RSC Advances · doi:10.1039/c8ra10433f · Cited by 30
Auch, M., Kuthada, T., Giese, S., & Wagner, A. (2023) · Batteries · doi:10.3390/batteries9050274 · Cited by 38
Metadata
- Authors
- Bernardi, D., Pawlikowski, E., & Newman, J.
- Affiliations
- University of California, Berkeley (US)
- ORCID
- Newman, J.
- Venue
- Journal of The Electrochemical Society
- Publisher
- The Electrochemical Society
- Published
- 1985-01-01
- Volume
- 132
- Issue
- 1
- Pages
- 5-12
- ISSN
- 0013-4651 (ISSN-L)
- 1945-7111
- OpenAlex
- W2023385933
- Cited by
- 2,548
- References
- 0
- Citations by year
- 2026: 383 · 2025: 387 · 2024: 339 · 2023: 265 · 2022: 238 · 2021: 167 · 2020: 147 · 2019: 106 · 2018: 74 · 2017: 89 · 2016: 42 · 2015: 53 · 2014: 75 · 2013: 51 · 2012: 31
- FWCI
- 0.00
- Type
- journal article
- Language
- en
- Open access
- bronze
- doi.org
- Licence
- iopscience.iop.org/page/copyright (vor, 12758 d)
- iopscience.iop.org/info/page/text-and-data-mining (tdm, 12758 d)
- Locations
- Journal of The Electrochemical Society (publishedVersion)
- Topics
- Physical Sciences › Engineering › Automotive Engineering › Battery Modeling and Management
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Advancements in Battery Materials
- Physical Sciences › Chemistry › Electrochemistry › Molten salt chemistry and electrochemical processes
- Keywords
- heat generation rate, Joule heating, phase transitions, mixing effects, electrochemical reactions, battery thermal management, battery modeling
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.