The DOI matches its Crossref record; 48 of the 48 references it cites were found in a registry or an index.
Laser and Electron Beam Additive Manufacturing Methods of Fabricating Titanium Bone Implants
Open accessAbstract
Additive Manufacturing (AM) methods are generally used to produce an early sample or near net-shape elements based on three-dimensional geometrical modules. To date, publications on AM of metal implants have mainly focused on knee and hip replacements or bone scaffolds for tissue engineering. The direct fabrication of metallic implants can be achieved by methods, such as Selective Laser Melting (SLM) or Electron Beam Melting (EBM). This work compares the SLM and EBM methods used in the fabrication of titanium bone implants by analyzing the microstructure, mechanical properties and cytotoxicity. The SLM process was conducted in an environmental chamber using 0.4–0.6 vol % of oxygen to enhance the mechanical properties of a Ti-6Al-4V alloy. SLM processed material had high anisotropy of mechanical properties and superior UTS (1246–1421 MPa) when compared to the EBM (972–976 MPa) and the wrought material (933–942 MPa). The microstructure and phase composition depended on the used fabrication method. The AM methods caused the formation of long epitaxial grains of the prior β phase. The equilibrium phases (α + β) and non-equilibrium α’ martensite was obtained after EBM and SLM, respectively. Although it was found that the heat transfer that occurs during the layer by layer generation of the component caused aluminum content deviations, neither methods generated any cytotoxic effects. Furthermore, in contrast to SLM, the EBM fabricated material met the ASTMF136 standard for surgical implant applications.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Metal Additive Manufacturing: A Review
Frazier, W. E. (2014) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-014-0958-z · Cited by 5,984
Ti based biomaterials, the ultimate choice for orthopaedic implants – A review
Geetha, M., Singh, A. K., Asokamani, R., & Gogia, A. K. (2009) · Progress in Materials Science · doi:10.1016/j.pmatsci.2008.06.004 · Cited by 5,416
Additive manufacturing of metals
Herzog, D., Seyda, V., Wycisk, E., & Emmelmann, C. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.07.019 · Cited by 4,759
Additive Manufacturing Technologies: Rapid Prototyping to Direct Digital Manufacturing
Gibson, I., Rosen, D. W., & Stucker, B. (2010) · National University of Singapore · doi:10.1007/978-1-4419-1120-9 · Cited by 2,969
A study of the microstructural evolution during selective laser melting of Ti–6Al–4V
Thijs, L., Verhaeghe, F., Craeghs, T., Humbeeck, J. V., & Kruth, J.-P. (2010) · Acta Materialia · doi:10.1016/j.actamat.2010.02.004 · Cited by 2,929
Metal Additive Manufacturing: A Review of Mechanical Properties
Lewandowski, J. J., & Seifi, M. (2016) · Annual Review of Materials Research · doi:10.1146/annurev-matsci-070115-032024 · Cited by 1,722
Xu, W., Brandt, M., Sun, S., Elambasseril, J., Liu, Q., Latham, K., Xia, K., & Qian, M. (2015) · Acta Materialia · doi:10.1016/j.actamat.2014.11.028 · Cited by 1,245
Gong, H., Rafi, K., Gu, H., Starr, T., & Stucker, B. (2014) · Additive Manufacturing · doi:10.1016/j.addma.2014.08.002 · Cited by 1,038
Effect of the build orientation on the mechanical properties and fracture modes of SLM Ti–6Al–4V
Simonelli, M., Tse, Y. Y., & Tuck, C. (2014) · Materials Science and Engineering: A · doi:10.1016/j.msea.2014.07.086 · Cited by 1,010
Mechanical behavior of additive manufactured, powder-bed laser-fused materials
Mower, T. M., & Long, M. J. (2016) · Materials Science and Engineering: A · doi:10.1016/j.msea.2015.10.068 · Cited by 1,001
Murr, L. E., Quinones, S. A., Gaytan, S. M., Lopez, M. I., Rodela, A., Martinez, E. Y., Hernandez, D. H., Martinez, E., Medina, F., & Wicker, R. B. (2009) · Journal of the Mechanical Behavior of Biomedical Materials · doi:10.1016/j.jmbbm.2008.05.004 · Cited by 997
Rafi, H. K., Karthik, N. V., Gong, H., Starr, T. L., & Stucker, B. E. (2013) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-013-0658-0 · Cited by 987
Formation and control of martensite in Ti-6Al-4V alloy produced by selective laser melting
Yang, J., Yu, H., Yin, J., Gao, M. X., Wang, Z., & Zeng, X. (2016) · Materials & Design · doi:10.1016/j.matdes.2016.06.117 · Cited by 913
Heinl, P., Müller, L., Körner, C., Singer, R. F., & Müller, F. A. (2008) · Acta Biomaterialia · doi:10.1016/j.actbio.2008.03.013 · Cited by 815
Biocompatibility of Advanced Manufactured Titanium Implants—A Review
Sidambe, A. (2014) · Materials · doi:10.3390/ma7128168 · Cited by 741
Rapid manufacturing of metal components by laser forming
Santos, E. C., Shiomi, M., Osakada, K., & Laoui, T. (2006) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2005.09.005 · Cited by 740
Xu, W., Lui, E. W., Pateras, A., Qian, M., & Brandt, M. (2017) · Acta Materialia · doi:10.1016/j.actamat.2016.12.027 · Cited by 687
Zhao, X., Li, S., Zhang, M., Liu, Y., Sercombe, T. B., Wang, S., Hao, Y., Yang, R., & Murr, L. E. (2016) · Materials & Design · doi:10.1016/j.matdes.2015.12.135 · Cited by 673
Thijs, L., Montero Sistiaga, M. L., Wauthle, R., Xie, Q., Kruth, J.-P., & Van Humbeeck, J. (2013) · Acta Materialia · doi:10.1016/j.actamat.2013.04.036 · Cited by 672
Overview of Materials Qualification Needs for Metal Additive Manufacturing
Seifi, M., Salem, A., Beuth, J., Harrysson, O., & Lewandowski, J. J. (2016) · JOM · doi:10.1007/s11837-015-1810-0 · Cited by 630
Murr, L. E., Esquivel, E. V., Quinones, S. A., Gaytan, S. M., Lopez, M. I., Martinez, E. Y., Medina, F., Hernandez, D. H., Martinez, E., Martinez, J. L., et al. (2009) · Materials Characterization · doi:10.1016/j.matchar.2008.07.006 · Cited by 564
Trosch, T., Strößner, J., Völkl, R., & Glatzel, U. (2016) · Materials Letters · doi:10.1016/j.matlet.2015.10.136 · Cited by 556
Kunze, K., Etter, T., Grässlin, J., & Shklover, V. (2014) · Materials Science and Engineering A · doi:10.1016/j.msea.2014.10.003 · Cited by 515
Ductility of a Ti‐6Al‐4V alloy produced by selective laser melting of prealloyed powders
Facchini, L., Magalini, E., Robotti, P., Molinari, A., Höges, S., & Wissenbach, K. (2010) · Rapid Prototyping Journal · doi:10.1108/13552541011083371 · Cited by 512
Highly Anisotropic Steel Processed by Selective Laser Melting
Niendorf, T., Leuders, S., Riemer, A., Richard, H. A., Tröster, T., & Schwarze, D. (2013) · Metallurgical and Materials Transactions B · doi:10.1007/s11663-013-9875-z · Cited by 506
Trevisan, F., Calignano, F., Lorusso, M., Pakkanen, J., Aversa, A., Ambrosio, E., Lombardi, M., Fino, P., & Manfredi, D. (2017) · Materials · doi:10.3390/ma10010076 · Cited by 502
Practical considerations and capabilities for laser assisted direct metal deposition
Lewis, G. K., & Schlienger, E. (2000) · Materials & Design (1980-2015) · doi:10.1016/s0261-3069(99)00078-3 · Cited by 484
Hollander, D. A., von Walter, M., Wirtz, T., Sellei, R., Schmidt-Rohlfing, B., Paar, O., & Erli, H.-J. (2006) · Biomaterials · doi:10.1016/j.biomaterials.2005.07.041 · Cited by 482
Electron Beam Additive Manufacturing of Titanium Components: Properties and Performance
Edwards, P., O'Conner, A., & Ramulu, M. (2013) · Journal of Manufacturing Science and Engineering · doi:10.1115/1.4025773 · Cited by 450
Low stiffness porous Ti structures for load-bearing implants
Krishna, B. V., Bose, S., & Bandyopadhyay, A. (2007) · Acta Biomaterialia · doi:10.1016/j.actbio.2007.03.008 · Cited by 441
Physical Aspects of Process Control in Selective Laser Sintering of Metals
Das, S. (2003) · Advanced Engineering Materials · doi:10.1002/adem.200310099 · Cited by 434
Microstructure and mechanical behaviour of Ti―6Al―7Nb alloy produced by selective laser melting
Chlebus, E., Kuźnicka, B., Kurzynowski, T., & Dybała, B. (2011) · Materials Characterization · doi:10.1016/j.matchar.2011.03.006 · Cited by 423
Microstructure and mechanical behavior of porous Ti–6Al–4V parts obtained by selective laser melting
Sallica-Leva, E., Jardini, A. L., & Fogagnolo, J. B. (2013) · Journal of the Mechanical Behavior of Biomedical Materials · doi:10.1016/j.jmbbm.2013.05.011 · Cited by 340
Next Generation Orthopaedic Implants by Additive Manufacturing Using Electron Beam Melting
Murr, L. E., Gaytan, S. M., Martinez, E., Medina, F., & Wicker, R. B. (2012) · International Journal of Biomaterials · doi:10.1155/2012/245727 · Cited by 306
The Influence of Processing Parameters on the Mechanical Properties of SLM Parts
Hanzl, P., Zetek, M., Bakša, T., & Kroupa, T. (2015) · Procedia Engineering · doi:10.1016/j.proeng.2015.01.510 · Cited by 291
Fabrication of Ti-6Al-4V Scaffolds by Direct Metal Deposition
Dinda, G. P., Song, L., & Mazumder, J. (2008) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-008-9634-y · Cited by 288
Correlation between Young's modulus and porosity in porous materials
Kováčik, J. (1999) · Journal of Materials Science Letters · doi:10.1023/a:1006669914946 · Cited by 277
Net shaped high performance oxide ceramic parts by selective laser melting
Yves-Christian, H., Jan, W., Wilhelm, M., Konrad, W., & Reinhart, P. (2010) · Physics Procedia · doi:10.1016/j.phpro.2010.08.086 · Cited by 276
Highly porous titanium scaffolds for orthopaedic applications
Dabrowski, B., Swieszkowski, W., Godlinski, D., & Kurzydlowski, K. J. (2010) · Journal of Biomedical Materials Research Part B: Applied Biomaterials · doi:10.1002/jbm.b.31682 · Cited by 272
Koike, M., Greer, P., Owen, K., Guo, L., Murr, L. E., Gaytan, S. M., Martinez, E., & Okabe, T. H. (2011) · Materials · doi:10.3390/ma4101776 · Cited by 270
Biomedical titanium alloys and their additive manufacturing
Hao, Y., Li, S., & Yang, R. (2016) · Rare Metals · doi:10.1007/s12598-016-0793-5 · Cited by 267
Murr, L. E., Gaytan, S. M., Medina, F., Martinez, E., Martinez, J. L., Hernandez, D. H., Machado, B. I., Ramirez, D. A., & Wicker, R. B. (2010) · Materials Science and Engineering: A · doi:10.1016/j.msea.2009.11.015 · Cited by 258
Macropore tissue ingrowth: a quantitative and qualitative study on hydroxyapatite ceramic
van Blitterswijk, C. A., Grote, J. J., Kuijpers, W., Daems, W. T., & de Groot, K. (1986) · Biomaterials · doi:10.1016/0142-9612(86)90071-2 · Cited by 198
Evaluation of titanium alloy fabricated using electron beam melting system for dental applications
Koike, M., Martinez, K., Guo, L., Chahine, G., Kovacevic, R., & Okabe, T. (2011) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2011.03.013 · Cited by 182
Schliephake, H., Neukam, F. W., & Klosa, D. (1991) · International Journal of Oral and Maxillofacial Surgery · doi:10.1016/s0901-5027(05)80698-8 · Cited by 126
Smith, C. J. M., Derguti, F., Hernández-Nava, E., Thomas, M., Tammas‐Williams, S., Gulizia, S., Fraser, D., & Todd, I. (2015) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2015.08.028 · Cited by 108
Effect of Melt Scan Rate on Microstructure and Macrostructure for Electron Beam Melting of Ti-6Al-4V
Puebla, K., Murr, L. E., Gaytan, S. M., Martinez, E., Medina, F. R., & Wicker, R. B. (2012) · Materials Sciences and Applications · doi:10.4236/msa.2012.35038 · Cited by 85
Selective laser sintering/melting of nitinol–hydroxyapatite composite for medical applications
Шишковский, И. В., Yadroitsev, I. A., & Smurov, I. Y. (2011) · Powder Metallurgy and Metal Ceramics · doi:10.1007/s11106-011-9329-6 · Cited by 48
Cited by
Additive manufacturing of Ti6Al4V alloy: A review
Liu, S., & Shin, Y. C. (2019) · Materials & Design · doi:10.1016/j.matdes.2018.107552 · Cited by 2,472
Svetlizky, D., Das, M., Zheng, B., Vyatskikh, A. L., Bose, S., Bandyopadhyay, A., Schoenung, J. M., Lavernia, E. J., & Eliaz, N. (2021) · Materials Today · doi:10.1016/j.mattod.2021.03.020 · Cited by 1,371
Benedetti, M., du Plessis, A., Ritchie, R. O., Dallago, M., Razavi, N., & Berto, F. (2021) · Materials Science and Engineering: R: Reports · doi:10.1016/j.mser.2021.100606 · Cited by 788
Nguyen, H. D., Pramanik, A., Basak, A. K., Dong, Y., Prakash, C., Debnath, S., Shankar, S., Jawahir, I. S., Dixit, S., & Buddhi, D. (2022) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2022.04.055 · Cited by 634
An overview of residual stresses in metal powder bed fusion
Bartlett, J. L., & Li, X. (2019) · Additive Manufacturing · doi:10.1016/j.addma.2019.02.020 · Cited by 616
Metadata
- Authors
- Wysocki, B., Maj, P., Sitek, R., Buhagiar, J., Kurzydłowski, K., & Święszkowski, W.
- Venue
- Applied Sciences
- Publisher
- MDPI AG
- Published
- 2017-06-26
- Volume
- 7
- Issue
- 7
- Pages
- 657
- ISSN
- 2076-3417 (ISSN-L)
- OpenAlex
- W2720993591
- Cited by
- 300
- References
- 48
- FWCI
- 14.56
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.