Fastest Thickness Measurements with a Terahertz Time-Domain System Based on Electronically Controlled Optical Sampling
Open accessThe DOI matches its Crossref record; 36 of the 36 references it cites were found in a registry or an index; 8 of the 16 sources its claims cite were checked for support.
Abstract
We apply a fast terahertz time-domain spectroscopy (TDS) system based on electronically controlled optical sampling (ECOPS) to contact-free thickness gauging. Our setup achieves a measurement speed of 1600 terahertz pulse traces per second, which—to our knowledge—represents the fastest thickness measurement performed with any terahertz system to-date. Using a silicon wafer as a test sample, we compare data of the ECOPS experiment to results obtained with a conventional terahertz TDS system and a mechanical micrometer gauge. We show that all systems provide consistent results within the measurement accuracy. Moreover, we perform thickness measurements of a rapidly moving sample and characterize the ECOPS setup with respect to time-domain dynamic range, signal-to-noise ratio, and spectral properties.
Overview
CoChat Summary
TL;DR
This paper characterizes an electronically controlled optical sampling (ECOPS) terahertz time-domain system for fast thickness gauging, achieving up to 1600 pulse traces/s at 200 ps scan range and 200 traces/s at 700 ps scan range. It demonstrates non-contact thickness measurements of a high-resistivity silicon wafer that agree with a conventional TDS system and a micrometer gauge, including on a moving sample at ~700 mm/s.
Key findings
- ECOPS reaches a maximum measurement speed of 1600 pulse traces/s at 200 ps scan range; at 700 ps scan range it maintains 200 traces/s. At maximum speed it is ~40× faster than the state-of-the-art TDS unit with mechanical delay, and at the lowest speed it still exceeds that system by ~5×. It is 160× faster than the TeraFlash pro at 1600 vs. 10 traces/s; after 10-trace averaging it remains 16× faster.
- Single-shot TD-DR is 61 dB, independent of measurement speed, while the TeraFlash pro achieves 82 dB. Averaging 10, 100, and 1000 traces increases ECOPS TD-DR by approximately 10, 20, and 30 dB, respectively; ECOPS achieves 91 dB in less than one second. Single-shot TD-SNR is 50 dB at 1600 Hz and 55 dB at 200 Hz, versus 74 dB for the TeraFlash pro; a factor of 10 in averaging improves TD-SNR by ~10 dB. Single-shot PDR is 38 dB with signal reaching the noise floor at 3.4 THz; with 1000 averages PDR increases to 68 dB and detectable signal extends to ~4.8 THz within 0.6 s.
- Thickness measurements of the silicon wafer gave 527 ± 1.5 µm with ECOPS, 527.94 ± 0.04 µm with the TeraFlash pro, and 527.5 ± 2.5 µm with the micrometer gauge; all three agree within a 1-sigma error margin, though TeraFlash pro scatter is ~40× smaller than ECOPS. On a moving sample at ~700 mm/s, ECOPS achieved spatial resolution of ~0.4 mm; thickness varied along the sample by as much as 10 µm, with ECOPS and micrometer-gauge results in good agreement. Preliminary results indicate layers as thin as ~30 µm can still be accurately determined.
Methods
- The ECOPS setup uses two passively mode-locked femtosecond lasers at ~1560 nm, 80 MHz repetition rate, <80 fs pulse width, and ~25 mW incident power on the terahertz antennas. One laser is fixed (“Master”); the other (“Slave”) has a tunable repetition rate via a piezo-actuated mirror and is phase-locked with a PID controller. Photoconductive switches based on InAlAs/InGaAs are used for terahertz generation and detection. Measurements use a reflection setup at 8° incidence with ~2.5 mm terahertz spot size, a 3.5 MHz transimpedance amplifier with 10^6 V/A gain, and a digital oscilloscope.
- Thickness is extracted via time-of-flight from the time difference between zero-crossings of pulse echoes from the front and back surfaces of an un-doped high-resistivity silicon wafer (n ~3.4). Results are compared with a TeraFlash pro at 10 traces/s and a manual micrometer gauge; terahertz measurements were repeated 10,000 times and micrometer measurements 50 times. A moving-sample test used a vinyl-record player at 45 rpm, translating to ~700 mm/s lateral velocity.
Limitations
- Stated: the difference between ECOPS TD-SNR at 1600 Hz and 200 Hz is still subject to further investigation, tentatively attributed to increased timing jitter at higher speed affecting signal amplitude reproducibility. Minimum resolvable layer thickness results are preliminary and not shown; ~30 µm is reported, with thinner layers surmised possible using more sophisticated post-processing. ECOPS is 160× faster than the TeraFlash pro but has ~40× larger scatter; repeatability on the 1 µm level is deemed sufficient for many industrial applications.
- Evident: thickness validation used a single high-resistivity silicon wafer and a mock-up conveyor (vinyl-record player), not a real production line; the reported ~0.4 mm spatial resolution does not consider the actual focus size.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
4 Valid · 1 Not valid · 5 Not checked · 51 Own results and interpretations
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“femtosecond fiber lasers in the telecom wavelength regime of 1.5 µm-the workhorses in most of today's terahertz TDS systems [15,24]-have typical repetition rates between 250 MHz and 40 MHz.”
§ Fastest Thickness Measurements with a Terahertz Time-Domain System Based on Electronically Controlled Optical Sampling > 1. Introduction
What the sources say
- Partly supportedcites [15] Vieweg, 2014, Terahertz-time domain spectrometer with 90 dB peak dynamic range, J. Infrared Millim. Terahertz Waves sourceExperimental — accuracy not yet measured
The Introduction (p. 1) describes a trend toward 1.5 μm fiber lasers in terahertz systems, and §2.2 (p. 4) reports a 1560 nm femtosecond laser operating at 100 MHz. The paper does not establish that these lasers are used in most THz-TDS systems or that their typical repetition rates span 40–250 MHz; 100 MHz is a specification of this system, not a general range. (LLM, conf=0.86)
- Partly supportedcites [24] Sartorius, 2008, All-fiber terahertz time-domain spectrometer operating at 1.5 μm telecom wavelengths, Opt. Express sourceExperimental — accuracy not yet measured
Section 3 (page not specified) describes a 1550 nm fiber laser delivering 100 fs pulses at a 100 MHz repetition rate, supporting one example within the claimed range. The paper does not establish that 40–250 MHz is typical of such lasers generally. (LLM, conf=0.85)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Note, however, that the scatter of the TeraFlash pro results is approx.40 times smaller than that of the ECOPS measurement.”
§ Fastest Thickness Measurements with a Terahertz Time-Domain System Based on Electronically Controlled Optical Sampling > 4. Thickness Gauging
hedgedstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The ECOPS technology is then ~40 times faster than our state-of-the-art TDS unit with mechanical delay.”
§ Fastest Thickness Measurements with a Terahertz Time-Domain System Based on Electronically Controlled Optical Sampling > 3. System Characterization
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“With ECOPS, the TeraFlash pro, and the micrometer gauge, we obtain thickness values of 527 ± 1.5 µm, 527.94 ± 0.04 µm, and 527.5 ± 2.5 µm, respectively.”
§ Fastest Thickness Measurements with a Terahertz Time-Domain System Based on Electronically Controlled Optical Sampling > 4. Thickness Gauging
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The ECOPS technology is then ~40 times faster than our stateof-the-art TDS unit with mechanical delay.”
§ Fastest Thickness Measurements with a Terahertz Time-Domain System Based on Electronically Controlled Optical Sampling > 3. System Characterization
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
37 more claims
Create a free account to see all 61 claims and every source verdict.
- It may state two separate claims as one. 17
- The quote only partly states this claim. 1
- Probably not a substantial claim. 4
Citations
Cites
The HITRAN2016 molecular spectroscopic database
Gordon, I. E., Rothman, L. S., Hill, C., Kochanov, R. V., Tan, Y., Bernath, P. F., Birk, M., Boudon, V., Campargue, A., Chance, K. V., et al. (2017) · Journal of Quantitative Spectroscopy and Radiative Transfer · doi:10.1016/j.jqsrt.2017.06.038 · Cited by 7,721
The HITRAN2012 molecular spectroscopic database
Rothman, L. S., Gordon, I. E., Babikov, Y., Barbe, A., Chris Benner, D., Bernath, P. F., Birk, M., Bizzocchi, L., Boudon, V., Brown, L. R., et al. (2013) · Journal of Quantitative Spectroscopy and Radiative Transfer · doi:10.1016/j.jqsrt.2013.07.002 · Cited by 3,255 · cited 2×
“All of the dips observed in the spectrum correspond to literature values of water vapor absorption lines, as documented in the HITRAN database [33].”
MethodResultFar-infrared time-domain spectroscopy with terahertz beams of dielectrics and semiconductors
Grischkowsky, D., Keiding, S., van Exter, M., & Fattinger, C. (1990) · Journal of the Optical Society of America B · doi:10.1364/josab.7.002006 · Cited by 2,239 · cited 1×
“Most of the work accomplished to-date made use of conventional terahertz TDS systems [14].”
BackgroundA reliable method for extraction of material parameters in terahertz time-domain spectroscopy
Duvillaret, L., Garet, F., & Coutaz, J.-L. (1996) · IEEE Journal of Selected Topics in Quantum Electronics · doi:10.1109/2944.571775 · Cited by 994 · cited 1×
“Initial work on terahertz-based thickness measurements dates back to the 1990s [3,4], when Duvillaret et al.”
BackgroundMaterial parameter estimation with terahertz time-domain spectroscopy
Dorney, T. D., Baraniuk, R. G., & Mittleman, D. M. (2001) · Journal of the Optical Society of America A · doi:10.1364/josaa.18.001562 · Cited by 807
Duvillaret, L., Garet, F., & Coutaz, J.-L. (1999) · Applied Optics · doi:10.1364/ao.38.000409 · Cited by 505 · cited 1×
“Initial work on terahertz-based thickness measurements dates back to the 1990s [3,4], when Duvillaret et al.”
BackgroundUltrafast time-domain spectroscopy based on high-speed asynchronous optical sampling
Bartels, A., Cerna, R., Kistner, C., Thoma, A., Hudert, F., Janke, C., & Dekorsy, T. (2007) · Review of Scientific Instruments · doi:10.1063/1.2714048 · Cited by 460 · cited 1×
“Lasers with GHz repetition rates can, in principle, reduce the amount of “dead time”, yet these repetition rates call for more complex Ti:sapphire systems [20,25].”
BackgroundHighly accurate optical material parameter determination with THz time-domain spectroscopy
Pupeza, I., Wilk, R., & Koch, M. (2007) · Optics Express · doi:10.1364/oe.15.004335 · Cited by 351
Optical and electronic properties of doped silicon from 0.1 to 2 THz
van Exter, M., & Grischkowsky, D. (1990) · Applied Physics Letters · doi:10.1063/1.103120 · Cited by 306
Nondestructive analysis of tablet coating thicknesses using terahertz pulsed imaging
Fitzgerald, A. J., Cole, B. E., & Taday, P. F. (2005) · Journal of Pharmaceutical Sciences · doi:10.1002/jps.20225 · Cited by 289 · cited 1×
“Subsequent works focused on introducing new algorithms for the extraction of material parameters [5–7], on paint thickness [8–10] and coating layer [11,12] gauging, and on the identification of concealed defects [13].”
BackgroundTerahertz paintmeter for noncontact monitoring of thickness and drying progress in paint film
Yasui, T., Yasuda, T., Sawanaka, K.-I., & Araki, T. (2005) · Applied Optics · doi:10.1364/ao.44.006849 · Cited by 273
All-fiber terahertz time-domain spectrometer operating at 1.5 μm telecom wavelengths
Sartorius, B., Roehle, H., Künzel, H., Böttcher, J., Schlak, M., Stanze, D., Venghaus, H., & Schell, M. (2008) · Optics Express · doi:10.1364/oe.16.009565 · Cited by 265
A review of optical NDT technologies
Zhu, Y.-K., Tian, G.-Y., Lu, R.-S., & Zhang, H. (2011) · Sensors · doi:10.3390/s110807773 · Cited by 228
Zeitler, J. A., Shen, Y., Baker, C., Taday, P. F., Pepper, M., & Rades, T. (2007) · Journal of Pharmaceutical Sciences · doi:10.1002/jps.20789 · Cited by 208 · cited 1×
“Subsequent works focused on introducing new algorithms for the extraction of material parameters [5–7], on paint thickness [8–10] and coating layer [11,12] gauging, and on the identification of concealed defects [13].”
BackgroundTerahertz-time domain spectrometer with 90 dB peak dynamic range
Vieweg, N., Rettich, F., Deninger, A., Roehle, H., Dietz, R., Göbel, T., & Schell, M. (2014) · Journal of Infrared Millimeter and Terahertz Waves · doi:10.1007/s10762-014-0085-9 · Cited by 203 · cited 3×
“5 μm—the workhorses in most of today’s terahertz TDS systems [15,24]—have typical repetition rates between 250 MHz and 40 MHz.”
BackgroundMethodInfluentialSelf-citationNondestructive defect identification with terahertz time-of-flight tomography
Zhong, H., Xu, J., Xie, X., Yuan, T., Reightler, R., Madaras, E., & Zhang, X.-C. (2005) · IEEE Sensors Journal · doi:10.1109/jsen.2004.841341 · Cited by 169 · cited 1×
“Subsequent works focused on introducing new algorithms for the extraction of material parameters [5–7], on paint thickness [8–10] and coating layer [11,12] gauging, and on the identification of concealed defects [13].”
BackgroundSu, K., Shen, Y.-C., & Zeitler, J. A. (2014) · IEEE Transactions on Terahertz Science and Technology · doi:10.1109/tthz.2014.2325393 · Cited by 155
Janke, C., Först, M., Nagel, M., Kurz, H., & Bartels, A. (2005) · Optics Letters · doi:10.1364/ol.30.001405 · Cited by 141 · cited 1×
“Lasers with GHz repetition rates can, in principle, reduce the amount of “dead time”, yet these repetition rates call for more complex Ti:sapphire systems [20,25].”
BackgroundDietz, R. J. B., Vieweg, N., Puppe, T., Zach, A., Globisch, B., Göbel, T., Leisching, P., & Schell, M. (2014) · Optics Letters · doi:10.1364/ol.39.006482 · Cited by 119 · cited 1×
“The net effect is equal to a mechanical delay, just significantly faster, with data acquisition rates well in the kHz range [23].”
BackgroundSelf-citationPump/Probe Spectroscopy by Asynchronous Optical Sampling
Elzinga, P. A., Lytle, F. E., Jian, Y., King, G. B., & Laurendeau, N. M. (1987) · Applied Spectroscopy · doi:10.1366/0003702874868025 · Cited by 115
Wilmink, G. J., Ibey, B. L., Rivest, B. D., Grundt, J. E., Roach, W. P., Tongue, T. D., Schulkin, B. J., Laman, N., Peralta, X. G., Roth, C. C., et al. (2011) · Journal of Biomedical Optics · doi:10.1117/1.3570648 · Cited by 109
High-speed terahertz time-domain spectroscopy based on electronically controlled optical sampling
Kim, Y., & Yee, D.-S. (2010) · Optics Letters · doi:10.1364/ol.35.003715 · Cited by 107 · cited 1×
“demonstrated that ECOPS achieved a better dynamic range than ASOPS at the same measurement speed, or vice versa, a drastically (~50x) higher measurement speed for the same dynamic range [22].”
BackgroundIron doped InGaAs: Competitive THz emitters and detectors fabricated from the same photoconductor
Globisch, B., Dietz, R. J. B., Kohlhaas, R. B., Göbel, T., Schell, M., Alcer, D., Semtsiv, M., & Masselink, W. T. (2017) · Journal of Applied Physics · doi:10.1063/1.4975039 · Cited by 105 · cited 1×
“Their semiconductor composition is based on an InAlAs/InGaAs heterostructure [27,28], with the emitter being iron doped [29].”
BackgroundDietz, R. J. B., Globisch, B., Gerhard, M., Velauthapillai, A., Stanze, D., Roehle, H., Koch, M., Göbel, T., & Schell, M. (2013) · Applied Physics Letters · doi:10.1063/1.4817797 · Cited by 103
High-resolution THz spectrometer with kHz scan rates
Bartels, A., Thoma, A., Janke, C., Dekorsy, T., Dreyhaupt, A., Winnerl, S., & Helm, M. (2006) · Optics Express · doi:10.1364/opex.14.000430 · Cited by 88
Improvement of minimum paint film thickness for THz paint meters by multiple-regression analysis
Yasuda, T., Iwata, T., Araki, T., & Yasui, T. (2007) · Applied Optics · doi:10.1364/ao.46.007518 · Cited by 77
Metrology Issues and Solutions in THz Time-Domain Spectroscopy: Noise, Errors, Calibration
Naftaly, M. (2013) · IEEE Sensors Journal · doi:10.1109/jsen.2012.2208624 · Cited by 76
Carrier dynamics in Beryllium doped low-temperature-grown InGaAs/InAlAs
Globisch, B., Dietz, R. J. B., Stanze, D., Göbel, T., & Schell, M. (2014) · Applied Physics Letters · doi:10.1063/1.4874804 · Cited by 63 · cited 1×
“Their semiconductor composition is based on an InAlAs/InGaAs heterostructure [27,28], with the emitter being iron doped [29].”
BackgroundHigh-speed terahertz time-domain spectroscopy of cyclotron resonance in pulsed magnetic field
Molter, D., Ellrich, F., Weinland, T., George, S., Goiran, M., Keilmann, F., Beigang, R., & Léotin, J. (2010) · Optics Express · doi:10.1364/oe.18.026163 · Cited by 44
Sample Thickness Measurement with THz-TDS: Resolution and Implications
Jen, C.-Y., & Richter, C. P. (2014) · Journal of Infrared Millimeter and Terahertz Waves · doi:10.1007/s10762-014-0093-9 · Cited by 43
Electronically controlled optical sampling using 100 MHz repetition rate fiber lasers
Tauser, F., Rausch, C., Posthumus, J. H., & Lison, F. (2008) · Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE · doi:10.1117/12.764506 · Cited by 37
High-speed terahertz reflection three-dimensional imaging using beam steering
Yee, D.-S., Jin, K. H., Yahng, J. S., Yang, H., Kim, C. Y., & Ye, J. C. (2015) · Optics Express · doi:10.1364/oe.23.005027 · Cited by 35 · cited 1×
“Recently, the same group applied an ECOPS system to three-dimensional terahertz imaging [26].”
High-resolution THz spectrometer with kHz scan rates
Bartels, A., Thoma, A., Janke, C., Dekorsy, T., Dreyhaupt, A., Winnerl, S., & Helm, M. (2006) · Conference on Lasers and Electro-Optics · doi:10.1109/cleo.2006.4627701 · Cited by 5
A time-domain terahertz spectrometer with 90 dB dynamic range
Vieweg, N., Rettich, F., Deninger, A. J., Roehle, H., Dietz, R. J. B., & Göbel, T. (2014) · International Conference on Infrared, Millimeter, and Terahertz Waves (IRMMW-THz) · doi:10.1109/irmmw-thz.2014.6956178 · Cited by 3
Self-citationHighly accurate material parameter extraction from THz time domain spectroscopy data
Pupeza, I., Wilk, R., Rutz, F., & Koch, M. (2007) · Quantum Electronics and Laser Science Conference · doi:10.1109/qels.2007.4431365 · Cited by 2
Electronically controlled optical sampling terahertz time-domain spectroscopy
Kim, Y., & Yee, D.-S. (2010) · International Conference on Infrared, Millimeter, and Terahertz Waves (IRMMW-THz) · doi:10.1109/icimw.2010.5612641 · Cited by 1
Research works printed but not linked: 1
- Naftaly, M., and Dudley, R.A. (2011, January 26–29). Calibration of Terahertz Spectrometers. In Proceeding of the International Society for Optical Engineering, Nanjing, China.
Cited by
Industrial Applications of Terahertz Sensing: State of Play
Naftaly, M., Vieweg, N., & Deninger, A. (2019) · Sensors · doi:10.3390/s19194203 · Cited by 317
“In addition, clever algorithms are needed to calculate layer thickness information from the THz data in real-time [20] and under industrial conditions.”
BackgroundSelf-citationTerahertz Quality Inspection for Automotive and Aviation Industries
Ellrich, F., Bauer, M., Schreiner, N., Keil, A., Pfeiffer, T., Klier, J., Weber, S., Jonuscheit, J., Friederich, F., & Molter, D. (2020) · Journal of Infrared, Millimeter, and Terahertz Waves · doi:10.1007/s10762-019-00639-4 · Cited by 184
Optoelectronic frequency-modulated continuous-wave terahertz spectroscopy with 4 THz bandwidth
Liebermeister, L., Nellen, S., Kohlhaas, R. B., Lauck, S., Deumer, M., Breuer, S., Schell, M. A., & Globisch, B. (2021) · Nature Communications · doi:10.1038/s41467-021-21260-x · Cited by 168
“(7) and (8), the photodetector current reads”
Nsengiyumva, W., Zhong, S., Zheng, L., Liang, W., Wang, B., Huang, Y., Chen, X., & Shen, Y. (2023) · IEEE Transactions on Instrumentation and Measurement · doi:10.1109/tim.2023.3318676 · Cited by 150
Experimental Comparison of UTC- and PIN-Photodiodes for Continuous-Wave Terahertz Generation
Nellen, S., Ishibashi, T., Deninger, A. J., Kohlhaas, R. B., Liebermeister, L., Schell, M. A., & Globisch, B. (2019) · Journal of Infrared Millimeter and Terahertz Waves · doi:10.1007/s10762-019-00638-5 · Cited by 102
“research, terahertz techniques have found their way into non-destructive testing [1], process control [2, 3], imaging [4], composition analysis [5–7], and wireless communications at carrier frequencies up to 600 GHz [8, 9].”
MethodSelf-citation
Metadata
- Authors
- Yahyapour, M., Jahn, A., Dutzi, K., Puppe, T., Leisching, P., Schmauss, B., Vieweg, N., & Deninger, A.
- Affiliations
- Friedrich-Alexander-Universität Erlangen-Nürnberg (DE)
- Toptica Photonics (Germany) (DE)
- Corresponding author
- Yahyapour, Milad
- Venue
- Applied Sciences
- Publisher
- MDPI AG
- Published
- 2019-03-27
- Volume
- 9
- Issue
- 7
- Pages
- 1283
- ISSN
- 2076-3417 (ISSN-L)
- OpenAlex
- W2935454897
- Semantic Scholar
- 622fb192aa65abdba81aa8c0935eaccdb00d623c
- Cited by
- 63
- References
- 33
- Citations by year
- 2026: 2 · 2025: 6 · 2024: 12 · 2023: 9 · 2022: 13 · 2021: 9 · 2020: 6 · 2019: 6
- FWCI
- 3.06
- Type
- journal article
- Language
- en
- Open access
- gold
- dx.doi.org
- Licence
- Locations
- Applied Sciences (publishedVersion, cc-by)
- OPUS Repository (Kooperativer Bibliotheksverbund Berlin-Brandenburg) (submittedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Terahertz technology and applications
- Physical Sciences › Engineering › Mechanics of Materials › Thermography and Photoacoustic Techniques
- Physical Sciences › Physics and Astronomy › Atomic and Molecular Physics, and Optics › Laser-Matter Interactions and Applications
- Keywords
- terahertz time-domain spectroscopy, thickness measurement, measurement speed, silicon wafers, signal-to-noise ratio
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.