Terahertz-time domain spectrometer with 90 dB peak dynamic range
Open accessThe DOI matches its Crossref record; 46 of the 46 references it cites were found in a registry or an index; 4 of the 22 sources its claims cite were checked for support.
Abstract
A single pulse trace of 50 ps is acquired in only 44 ms, and transformed into a spectrum with a peak dynamic range of 60 dB. With 1000 averages, the dynamic range increases to 90 dB.
Overview
CoChat Summary
TL;DR
The paper presents a compact, fiber-coupled terahertz time-domain spectrometer operating at 1.5 μm with InGaAs/InAlAs photoconductive switches, achieving a 90 dB peak dynamic range with 1000 averages in under one minute. It demonstrates the system for terahertz spectroscopy of polymers and terahertz imaging.
Key findings
- A single 50 ps pulse trace is acquired in 44 ms with a peak dynamic range (PDR) of 60 dB; 100 averages give 82 dB in 4.4 s, and 1000 averages give 90 dB while remaining well below one minute.
- The system has a bandwidth exceeding 4.5 THz with a signal peak at approximately 480 GHz, a terahertz pulse width of 650 fs, and a timing jitter of approximately 1.3 fs; the precise delay stage is said to improve PDR by more than 17 dB.
- Spectroscopy of HDPE (1.93 mm), PA (1.07 mm), and LCP (2.05 mm) shows HDPE absorption <0.1 cm⁻¹ below 1 THz and ~1 cm⁻¹ at 2 THz with refractive index 1.53; PA has refractive index 1.71 at 0.5 THz; LCP shows ordinary/extraordinary refractive indices of 1.86 and 2.03 at 0.5 THz and an absorption peak near 1.2 THz attributed to Talcum.
- Imaging examples reveal a speaker and circuit board inside a mail envelope and air bubbles in a polyamide step wedge; the 90 dB PDR is described as a record for commercial TD-THz systems.
Methods
- Design and characterization of a compact fiber-coupled THz-TDS system using a 1560 nm femtosecond fiber laser, a fast voice-coil delay stage, a long-travel delay line, and InGaAs/InAlAs photoconductive emitter and detector antennas.
- Spectroscopy used three polymer samples in a dry-air-purged box, with 1000 averages per trace (44 s measurement time) and material parameters extracted via a quasi-space algorithm comparing reference and sample pulses.
- Imaging used two test samples mounted on an XY scanner: a mail envelope with a birthday card and a polyamide step wedge, with specified scan areas, step sizes, speeds, and total measurement times.
Limitations
- The paper states that strong terahertz absorption in LCP and PA at high frequencies lowers the dynamic range and restricts the frequency span usable for analysis to ~2 THz.
- The paper notes that absolute PDR depends on other factors such as available terahertz power, receiver sensitivity, and electronic noise in the readout circuit.
- No dedicated limitations section is included; evident from the text, the imaging demonstrations were proof-of-principle and slow, with total measurement times just below two hours for the envelope and 65 min for the step wedge.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
2 Valid · 1 Not valid · 6 Not checked · 39 Own results and interpretations
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“This is an improvement of more than one order of magnitude, compared to the 10 fs level inferred from [35, 36].”
§ The Author(s) 2014. This article is published with open access at Springerlink.com > 2.5 Impact of jitter on the SNR · p. 6
What the sources say
- Could not verifycites [35] M. Theuer, R. Beigang, and D. Grischkowsky, “Highly sensitive terahertz measurement of layer thickness using a two-cylinder waveguide sensor,” Appl. Phys. Lett., vol. 97, no. 7, p. 071106, 2010. sourceExperimental — accuracy not yet measured
The cited paper discusses pulse-delay accuracy and reports a reference-zero drift of approximately 20 fs/h (opening passage) and a 0.014 ps drift during a measurement series (Fig. 1 discussion). Neither establishes a 10 fs time-resolution level. Searches for “10 fs” and temporal-resolution accuracy found no passage supporting that inferred benchmark; the citing system’s 1.3 fs result is not attributed to this source. (LLM, conf=0.70)
- Not checked — no full text of the sourcecites [36] C. D. Stoik, “Nondestructive evaluation of aircraft composites using terahertz time domain spectroscopy,” PhD Thesis, Air Force Inst. Technol., 2008. source
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Could not verify
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The system described here determines the delay position with an uncertainty below 400 nm”
§ The Author(s) 2014. This article is published with open access at Springerlink.com > 2.5 Impact of jitter on the SNR · p. 6
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“With 1000 averages, the dynamic range increases to 90 dB”
- Also stated in: § 2.1 System design and performance · p. 3 · plain
“The PDR increases to 90 dB for 1000 averages.”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Also stated in: § 2.1 System design and performance · p. 3 · plain
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The value of the time delay is measured with a resolution of 1.3 fs.”
- Also stated in: § 2.5 Impact of jitter on the SNR · p. 6 · plain
“and thus achieves a time resolution of 1.3 fs”
§ The Author(s) 2014. This article is published with open access at Springerlink.com > 2.3.1 Long-travel delay line · p. 4
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Also stated in: § 2.5 Impact of jitter on the SNR · p. 6 · plain
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The dispersive feature at around 1.2 THz corresponds to a distinct absorption peak, as seen in Fig. 5 (b).”
§ The Author(s) 2014. This article is published with open access at Springerlink.com > 3.1 Terahertz spectroscopy · p. 7
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
20 more claims
Create a free account to see all 48 claims and every source verdict.
- Probably not a substantial claim. 6
- It may state two separate claims as one. 21
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“For a delay length of several 100 picoseconds, the measurement speed of conventional systems ranges from a few to few 100 terahertz pulse traces per second [15][16][17], and thus falls short of the requirements for high-speed monitoring.”
From Fastest Thickness Measurements with a Terahertz Time-Domain System Based on Electronically Controlled Optical Sampling (2019) · cites this paper as [15]
Experimental — accuracy not yet measuredThe source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“femtosecond fiber lasers in the telecom wavelength regime of 1.5 µm-the workhorses in most of today's terahertz TDS systems [15,24]-have typical repetition rates between 250 MHz and 40 MHz.”
From Fastest Thickness Measurements with a Terahertz Time-Domain System Based on Electronically Controlled Optical Sampling (2019) · cites this paper as [15]
Experimental — accuracy not yet measuredThe cited source says what the claim attributes to it.
In the citing paper
“The resulting n r (ω) spectrum of porous polyethylene derived from Eq. 21 (Fig. 5) is lower than the 1.53 to 1.54 range of solid polyethylene reported in literature [67, 68].”
From Tutorial: Accurate Determination of Refractive Index and Absorption Coefficient in Terahertz Time-Domain Spectroscopy (2025) · cites this paper as [68]
The cited source says what the claim attributes to it.
In the citing paper
“These results indicate that when the diluent is porous, as in the example of powdered polyethylene with n r = 1 . 46, using n r estimates based on the solid material (e.g., n r = 1 . 53 to 1.54 for solid polyethylene [67, 68]) can lead to inaccurate optical properties of the inclusion.”
From Tutorial: Accurate Determination of Refractive Index and Absorption Coefficient in Terahertz Time-Domain Spectroscopy (2025) · cites this paper as [68]
The cited source says what the claim attributes to it.
In the citing paper
“We attribute this difference to two decisive characteristics of the design: First, the TeraFlash pro benefits from an extremely precise mechanical delay [15], the low timing jitter of which translates into an excellent signal quality.”
From Fastest Thickness Measurements with a Terahertz Time-Domain System Based on Electronically Controlled Optical Sampling (2019) · cites this paper as [15]
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ The Author(s) 2014. This article is published with open access at Springerlink.com > 2.5 Impact of jitter on the SNR · p. 6
“The amplitude uncertainty reaches maximum values at the zero crossings of A(t), i.e. at t = k / 2 πν with k = 0, 1, 2, etc.”
§ The Author(s) 2014. This article is published with open access at Springerlink.com > 2.5 Impact of jitter on the SNR · p. 5
“A(t) = sin(2 πν THz t) with ν THz = 480 GHz”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ The Author(s) 2014. This article is published with open access at Springerlink.com > 2.5 Impact of jitter on the SNR · p. 6
“This is an improvement of more than one order of magnitude, compared to the 10 fs level inferred from [35, 36].”
§ The Author(s) 2014. This article is published with open access at Springerlink.com > 2.5 Impact of jitter on the SNR · p. 6
“and thus achieves a time resolution of 1.3 fs.”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ The Author(s) 2014. This article is published with open access at Springerlink.com > 3.2 Terahertz imaging · p. 8
“the total measurement time was 65 min.”
§ The Author(s) 2014. This article is published with open access at Springerlink.com > 3.2 Terahertz imaging · p. 8
“Figure 7 shows a photograph of the polyamide step wedge and a 100 mm x 40 mm terahertz image. The scan speed was 2 mm / s, the step size was 0.3 mm”
Citations
Cites
Far-infrared time-domain spectroscopy with terahertz beams of dielectrics and semiconductors
Grischkowsky, D., Keiding, S., van Exter, M., & Fattinger, C. (1990) · Journal of the Optical Society of America B · doi:10.1364/josab.7.002006 · Cited by 2,239
Terahertz spectroscopy and imaging - Modern techniques and applications
Jepsen, P. U., Cooke, D. G., & Koch, M. (2011) · Laser & Photonics Reviews · doi:10.1002/lpor.201000011 · Cited by 2,091 · cited 9×
“2.5 Impact of jitter on the SNR In THz-TDS, various noise effects compromise the signal quality [23–25].”
MethodInfluentialPicosecond photoconducting Hertzian dipoles
Auston, D. H., Cheung, K. P., & Smith, P. R. (1984) · Applied Physics Letters · doi:10.1063/1.95174 · Cited by 1,037 · cited 1×
“laser light into a terahertz pulse [18].”
Terahertz time-domain spectroscopy of water vapor
van Exter, M., Fattinger, C., & Grischkowsky, D. (1989) · Optics Letters · doi:10.1364/ol.14.001128 · Cited by 862
Recent advances in terahertz imaging
Mittleman, D. M., Gupta, M., Neelamani, R., Baraniuk, R. G., Rudd, J. V., & Koch, M. (1999) · Applied Physics B: Lasers and Optics · doi:10.1007/s003400050750 · Cited by 703
Exploring Dynamics in the Far-Infrared with Terahertz Spectroscopy
Schmuttenmaer, C. A. (2004) · Chemical Reviews · doi:10.1021/cr020685g · Cited by 659
Terahertz Spectroscopy and Imaging for Defense and Security Applications
Liu, H.-B., Zhong, H., Karpowicz, N., Chen, Y., & Zhang, X.-C. (2007) · Proceedings of the IEEE · doi:10.1109/jproc.2007.898903 · Cited by 636 · cited 1×
“fundamental research [5, 6], medical diagnostics [7], security applications [8] to non destructive testing [9–12].”
BackgroundPrinciples of Statistical Radiophysics 3
Rytov, S. M., Kravtsov, Y. A., & Tatarskii, V. I. (1989) · Springer eBooks · doi:10.1007/978-3-642-72685-9 · Cited by 635
Beard, M. C., Turner, G. M., & Schmuttenmaer, C. A. (2002) · The Journal of Physical Chemistry B · doi:10.1021/jp020579i · Cited by 608
Haus, H. A., & Mecozzi, A. (1993) · IEEE Journal of Quantum Electronics · doi:10.1109/3.206583 · Cited by 498
Characterization of an optoelectronic terahertz beam system
van Exter, M., & Grischkowsky, D. R. (1990) · IEEE Transactions on Microwave Theory and Techniques · doi:10.1109/22.60016 · Cited by 486 · cited 2×
“played a dominant role in the SNR budget [26, 31].”
BackgroundTerahertz pulsed spectroscopy and imaging in the pharmaceutical setting - a review
Zeitler, J. A., Taday, P. F., Newnham, D. A., Pepper, M., Gordon, K. C., & Rades, T. (2007) · Journal of Pharmacy and Pharmacology · doi:10.1211/jpp.59.2.0008 · Cited by 407
Dynamic range in terahertz time-domain transmission and reflection spectroscopy
Jepsen, P. U., & Fischer, B. M. (2005) · Optics Letters · doi:10.1364/ol.30.000029 · Cited by 382
Stoik, C. D., Bohn, M. J., & Blackshire, J. L. (2008) · Optics Express · doi:10.1364/oe.16.017039 · Cited by 377
All-fiber terahertz time-domain spectrometer operating at 1.5 μm telecom wavelengths
Sartorius, B., Roehle, H., Künzel, H., Böttcher, J., Schlak, M., Stanze, D., Venghaus, H., & Schell, M. (2008) · Optics Express · doi:10.1364/oe.16.009565 · Cited by 265
Self-citationProperties of Building and Plastic Materials in the THz Range
Piesiewicz, R., Jansen, C., Wietzke, S., Mittleman, D., Koch, M., & Kürner, T. (2007) · International Journal of Infrared and Millimeter Waves · doi:10.1007/s10762-007-9217-9 · Cited by 253
Handbook of terahertz technology for imaging, sensing and communications
Saeedkia, D. (2013) · Woodhead Publishing Limited eBooks · doi:10.1533/9780857096494 · Cited by 237 · cited 1×
“Terahertz waves feature unique properties: like microwaves, terahertz radiation passes through a plethora of non-conducting materials, including paper, cardboard, plastics, wood, ceramics and glass-fiber composites [1].”
BackgroundAnalyzing sub-100-μm samples with transmission terahertz time domain spectroscopy
Scheller, M., Jansen, C., & Koch, M. (2009) · Optics Communications · doi:10.1016/j.optcom.2008.12.061 · Cited by 194 · cited 1×
“For extraction of the material parameters we used a quasi-space algorithm [40].”
MethodUncertainty in terahertz time-domain spectroscopy measurement
Withayachumnankul, W., Fischer, B. M., Lin, H., & Abbott, D. (2008) · Journal of the Optical Society of America B · doi:10.1364/josab.25.001059 · Cited by 181
Next generation 15 µm terahertz antennas: mesa-structuring of InGaAs/InAlAs photoconductive layers
Roehle, H., Dietz, R. J. B., Hensel, H. J., Böttcher, J., Künzel, H., Stanze, D., Schell, M., & Sartorius, B. (2010) · Optics Express · doi:10.1364/oe.18.002296 · Cited by 181 · cited 2×
“Both transmitter and receiver feature a mesastructured gap region as detailed in [13].”
BackgroundSelf-citationPrinciples of Statistical Radiophysics 4
Rytov, S. M., Kravtsov, Y. A., & Tatarskii, V. I. (1989) · doi:10.1007/978-3-642-72682-8 · Cited by 153
Ultrafast Carrier Dynamics in Graphene under a High Electric Field
Tani, S., Blanchard, F., & Tanaka, K. (2012) · Physical Review Letters · doi:10.1103/physrevlett.109.166603 · Cited by 152 · cited 1×
“fundamental research [5, 6], medical diagnostics [7], security applications [8] to non destructive testing [9–12].”
BackgroundInfluence of noise on the characterization of materials by terahertz time-domain spectroscopy
Duvillaret, L., Garet, F., & Coutaz, J.-L. (2000) · Journal of the Optical Society of America B · doi:10.1364/josab.17.000452 · Cited by 151 · cited 1×
“Noise contributions include optical and electronic effects [26, 27], laser intensity variations [28], and jitter noise [29, 30].”
BackgroundPrinciples of statistical radiophysics. 4. Wave propagation through random media.
Rytov, S. M., Kravtsov, Y. A., & Tatarskii, V. I. (1989) · Cited by 133
Solvation dynamics of biomolecules: Modeling and terahertz experiments
Leitner, D. M., Gruebele, M., & Havenith, M. (2008) · HFSP journal · doi:10.2976/1.2976661 · Cited by 126 · cited 1×
“[15], measurements under rapidly changing environmental conditions, e.”
BackgroundDietz, R. J. B., Globisch, B., Gerhard, M., Velauthapillai, A., Stanze, D., Roehle, H., Koch, M., Göbel, T., & Schell, M. (2013) · Applied Physics Letters · doi:10.1063/1.4817797 · Cited by 103 · cited 1×
“The photoconductive emitter employs a high-mobility InAlAs/InGaAs multilayer heterostructure (MLHS) as described in [19, 20].”
Self-citationDietz, R. J. B., Gerhard, M., Stanze, D., Koch, M., Sartorius, B., & Schell, M. (2011) · Optics Express · doi:10.1364/oe.19.025911 · Cited by 86 · cited 1×
“The photoconductive emitter employs a high-mobility InAlAs/InGaAs multilayer heterostructure (MLHS) as described in [19, 20].”
Self-citationUltrabroadband terahertz spectroscopy of a liquid crystal
Vieweg, N., Fischer, B. M., Reuter, M., Kula, P., Dabrowski, R., Celik, M. A., Frenking, G., Koch, M., & Jepsen, P. U. (2012) · Optics Express · doi:10.1364/oe.20.028249 · Cited by 83
Self-citationWave propagation through random media
Кравцов, Ю. А., Tatarskii, V. I., & Rytov, S. M. (1989) · Springer eBooks · Cited by 75
Photoconductive response correction for detectors of terahertz radiation
Castro-Camus, E., Fu, L., Lloyd-Hughes, J., Tan, H. H., Jagadish, C., & Johnston, M. B. (2008) · Journal of Applied Physics · doi:10.1063/1.2969035 · Cited by 65 · cited 1×
“played a dominant role in the SNR budget [26, 31].”
BackgroundCarrier dynamics in Beryllium doped low-temperature-grown InGaAs/InAlAs
Globisch, B., Dietz, R. J. B., Stanze, D., Göbel, T., & Schell, M. (2014) · Applied Physics Letters · doi:10.1063/1.4874804 · Cited by 63 · cited 2×
“The receiver is based on an LT-grown Beryllium doped InAlAs/InGaAs MLHS [21, 22] with short carrier lifetime.”
BackgroundSelf-citationUltrabroadband terahertz spectroscopy of chalcogenide glasses
Zalkovskij, M., Bisgaard, C. Z., Novitsky, A. V., Malureanu, R., Savastru, D. M., Popescu, A. A., Jepsen, P. U., & Lavrinenko, A. V. (2012) · Applied Physics Letters · doi:10.1063/1.3676443 · Cited by 60
High-speed terahertz time-domain spectroscopy of cyclotron resonance in pulsed magnetic field
Molter, D., Ellrich, F., Weinland, T., George, S., Goiran, M., Keilmann, F., Beigang, R., & Léotin, J. (2010) · Optics Express · doi:10.1364/oe.18.026163 · Cited by 44
Highly sensitive terahertz measurement of layer thickness using a two-cylinder waveguide sensor
Theuer, M., Beigang, R., & Grischkowsky, D. (2010) · Applied Physics Letters · doi:10.1063/1.3481080 · Cited by 38
Analysis of measurement uncertainty in THz-TDS
Withayachumnankul, W., Lin, H., Mickan, S. P., Fischer, B. M., & Abbott, D. (2007) · SPIE Proceedings · doi:10.1117/12.721876 · Cited by 29 · cited 1×
“In this section, we are going to discuss the effect of jitter noise, which has an equally significant impact on the attainable SNR level [25, 29, 32, 33].”
BackgroundDegree of dispersion of polymeric compounds determined with terahertz time‐domain spectroscopy
Krumbholz, N., Hochrein, T., Vieweg, N., Radovanovic, I., Pupeza, I., Schubert, M. M., Kretschmer, K., & Koch, M. (2010) · Polymer Engineering and Science · doi:10.1002/pen.21798 · Cited by 22 · cited 1×
“varying temperatures or magnetic fields [16], and inline process control of plastic materials [17].”
BackgroundSelf-citationKhan, U. A., Nguyen, N., & Afsar, M. N. (2008) · IEEE Transactions on Instrumentation and Measurement · doi:10.1109/tim.2007.909601 · Cited by 21
Performance limits in TDR technique by Monte Carlo simulation
Letosa, J., Garcia-Gracia, M., Fornies-Marquina, J. M., & Artacho, J. M. (1996) · IEEE Transactions on Magnetics · doi:10.1109/20.497401 · Cited by 18 · cited 2×
“The “worst-case” amplitude error is given by dA= 2πνTHzdt [33] and the dependence of the dynamic range on the timing jitter can be written [37]”
BackgroundEXPERIMENTAL SIGNATURE OF REGISTRATION NOISE IN PULSED TERAHERTZ SYSTEMS
COHEN, N., HANDLEY, J. W., BOYLE, R. D., BRAUNSTEIN, S. L., & BERRY, E. (2006) · Fluctuation and Noise Letters · doi:10.1142/s0219477506003161 · Cited by 17
Terahertz waves and liquid crystals: prospects and challenges
Vieweg, N., & Deninger, A. (2013) · SPIE Proceedings · doi:10.1117/12.2013315 · Cited by 12
Self-citationNondestructive evaluation of aircraft composites using terahertz time domain spectroscopy
Stoik, C. D., Bohn, M. J., & Blackshire, J. L. (2008) · 2008 33rd International Conference on Infrared, Millimeter and Terahertz Waves · doi:10.1109/icimw.2008.4665841 · Cited by 12
Deviation of optical constants extracted in terahertz transmission spectroscopy
Xu, X., Wang, X., & Wang, L. (2006) · Applied Optics · doi:10.1364/ao.45.000648 · Cited by 12 · cited 1×
“In this section, we are going to discuss the effect of jitter noise, which has an equally significant impact on the attainable SNR level [25, 29, 32, 33].”
BackgroundExploring Dynamics in the Far‐Infrared with Terahertz Spectroscopy
Schmuttenmaer, C. A. (2004) · ChemInform · doi:10.1002/chin.200424293 · Cited by 12
Khan, U., Afsar, M. N., & Nguyen, N. (2006) · Conference proceedings - IEEE Instrumentation/Measurement Technology Conference · doi:10.1109/imtc.2006.328540 · Cited by 5 · cited 1×
“The absorption peak itself is caused by Talcum, a filling material, which is commonly added to LCP samples [42].”
BackgroundPhase noise investigation in terahertz time-domain spectroscopy measurements
Wojdyla, A., & Gallot, G. (2013) · 2013 38th International Conference on Infrared, Millimeter, and Terahertz Waves (IRMMW-THz) · doi:10.1109/irmmw-thz.2013.6665432 · Cited by 2 · cited 2×
“Noise contributions include optical and electronic effects [26, 27], laser intensity variations [28], and jitter noise [29, 30].”
BackgroundTerahertz‐Pulsed Spectroscopy and Imaging in Pharmaceutical Setting
Zeitler, J. A., Taday, P. F., Newnham, D. A., Pepper, M., Gordon, K. C., & Rades, T. (2007) · ChemInform · doi:10.1002/chin.200727273 · Cited by 1
Research works printed but not linked: 2
- C. H. Zhang, G. F. Zhao, B. B. Jin, Y. Y. Hou, H. H. Jia, J. Chen, and P. H. Wu, “Terahertz imaging on subcutaneous tissues and liver inflamed by liver cancer cells,” Terahertz Sci. Technol., vol. 5, no. 3, pp. 114–123, 2012.
- L. Wu, “Optimierung des Signal-Rausch-Abstands von AD-Wandlern,” Elektron. Ind., vol. 11, pp. 50–52, 2010.
Cited by
Industrial Applications of Terahertz Sensing: State of Play
Naftaly, M., Vieweg, N., & Deninger, A. (2019) · Sensors · doi:10.3390/s19194203 · Cited by 317
Self-citationHigh-throughput terahertz imaging: progress and challenges
Li, X., Li, J., Li, Y., Ozcan, A., & Jarrahi, M. (2023) · Light: Science & Applications · doi:10.1038/s41377-023-01278-0 · Cited by 296
Optoelectronic frequency-modulated continuous-wave terahertz spectroscopy with 4 THz bandwidth
Liebermeister, L., Nellen, S., Kohlhaas, R. B., Lauck, S., Deumer, M., Breuer, S., Schell, M. A., & Globisch, B. (2021) · Nature Communications · doi:10.1038/s41467-021-21260-x · Cited by 168
Self-citationHigh harmonic generation in undoped graphene: Interplay of inter- and intraband dynamics
Al-Naib, I. A. I., Sipe, J. E., & Dignam, M. M. (2014) · Physical Review B · doi:10.1103/physrevb.90.245423 · Cited by 154
Kato, M., Tripathi, S. R., Murate, K., Imayama, K., & Kawase, K. (2016) · Optics Express · doi:10.1364/oe.24.006425 · Cited by 153
Metadata
- Authors
- Vieweg, N., Rettich, F., Deninger, A., Roehle, H., Dietz, R., Göbel, T., & Schell, M.
- Affiliations
- Toptica Photonics (Germany) (DE)
- Fraunhofer Institute for Telecommunications, Heinrich Hertz Institute (DE)
- Corresponding author
- Vieweg, N.
- Venue
- Journal of Infrared Millimeter and Terahertz Waves
- Published
- 2014-07-09
- Volume
- 35
- Issue
- 10
- Pages
- 823-832
- ISSN
- 1866-6892 (ISSN-L)
- 1866-6906
- OpenAlex
- W1997920385
- Cited by
- 203
- References
- 43
- Citations by year
- 2026: 9 · 2025: 12 · 2024: 18 · 2023: 14 · 2022: 13 · 2021: 16 · 2020: 26 · 2019: 26 · 2018: 18 · 2017: 17 · 2016: 16 · 2015: 15 · 2014: 3
- FWCI
- 9.03
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Locations
- Journal of Infrared Millimeter and Terahertz Waves (publishedVersion, cc-by)
- Fraunhofer-Publica (Fraunhofer-Gesellschaft) (submittedVersion)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Terahertz technology and applications
- Physical Sciences › Physics and Astronomy › Atomic and Molecular Physics, and Optics › Laser-Matter Interactions and Applications
- Physical Sciences › Chemistry › Spectroscopy › Spectroscopy and Laser Applications
- Keywords
- dynamic range, time-domain reconstruction, signal averaging, terahertz imaging, terahertz spectroscopy
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.