The DOI matches its Crossref record; 162 of the 162 references it cites were found in a registry or an index; 7 of the 97 sources its claims cite were checked for support.
High Temperature Corrosion Resistant and Anti-slagging Coatings for Boilers: A Review
Open accessAbstract
Abstract High temperature corrosion and slag deposition significantly reduce the thermal efficiency and lifespan of biomass-fired boilers. Surface modification with protective coatings can enhance boiler performance and prevent commercial losses due to maintenance and damage. This review focuses on the development of corrosion-resistant coatings (CRCs) and anti-slagging coatings (ASCs) over the past decade. CRCs are explored through thermal spray processes that include arc spray, atmospheric plasma spray (APS), high-velocity oxygen fuel (HVOF), detonation gun (D-gun™), and cold spray. Studies on alloys, ceramics, and ceramic–metal composites are summarised, highlighting the high temperature corrosion prevention mechanisms and discussing new coating materials. ASCs are reviewed in the context of advancements via thermal spray and slurry spray methods. The mechanisms for slag reduction, testing methods to evaluate ASC effectiveness, and the necessary architecture for preventing slag deposition are examined. A lab-based rig simulating fly ash deposition onto water-cooled coating coupons for anti-slagging investigations is also presented. Further research is needed to develop and evaluate materials for ASCs effectively. Graphical Abstract
Overview
CoChat Summary
## TL;DR
This review summarizes corrosion-resistant coatings and anti-slagging coatings for industrial boilers, emphasizing thermal spray as the main fabrication route and nickel-based high-chromium alloys as the most established corrosion-resistant materials. It also argues that anti-slagging coatings are less developed, that standardized evaluation methods are lacking, and that future work should focus on faster deposition methods and dual-function coatings that resist both corrosion and slagging.
## Key findings
- Thermal spray coatings are widely investigated for high-temperature corrosion resistance in boilers, with Ni-based high-chromium alloys described as the most used materials; their protection comes from Ni and Cr oxide/spinel formation.
- The review notes that NiCr alloys may not be the most economical option, and that lower-cost FeCr alloys are receiving research attention.
- For anti-slagging, the paper says progress lags behind corrosion-resistant coatings; reported slag-reduction mechanisms include preventing corrosion that promotes slag adhesion and using low-surface-energy materials such as hexagonal boron nitride (h-BN) to weaken slag adhesion/wettability.
- The paper reports several quantitative examples from prior studies: arc-sprayed Ni-50Cr showed superior protection; a modified-nozzle arc-sprayed NiCrTi/NiCrMo coating achieved coating porosity below 2% with particle velocities of 152 ± 26 m/s; cold-sprayed Ni-20Cr and Ni-50Cr reduced corrosion-erosion rates by 58% and 72%, respectively; adding 1 wt% and 2 wt% CNTs to Cr3C2–20NiCr reduced corrosion rates by 80.71% and 82.96%, respectively.
## Methods
- This is a narrative review of coating development for boilers over the past decade, covering corrosion-resistant coatings and anti-slagging coatings.
- It synthesizes literature on multiple deposition routes, including arc spray, APS, HVOF, D-gun™, cold spray, slurry spray, laser cladding, weld overlay, diffusion coatings, and liquid thermal spray/suspension plasma spray.
- For anti-slagging evaluation, it also describes literature-based test approaches such as shear/tensile adhesion strength tests, contact-angle measurements of molten ash, and a bespoke flame-spray “slag testing rig” that deposits artificial slag on water-cooled coupons.
## Limitations
- The paper states that anti-slagging coatings are much less explored than corrosion-resistant coatings, and that further research is needed to develop and evaluate anti-slagging materials effectively.
- The paper explicitly notes that there is no accepted standard test to evaluate slag/fouling resistance of boiler surfaces or coatings.
- It also states that ceramic coatings still need evaluation in functioning boilers, and that thermal mismatch on metallic boiler components is a challenge.
- Evident from the text: because this is a review rather than a new experimental study, the paper does not report a single unified dataset or head-to-head controlled comparison generated by the authors themselves.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
7 Valid · 13 Not valid · 66 Not checked · 59 Own results and interpretations
The sources with a verdict support this claim; the rest weren’t checked yet, have no full text we could read, or their verdicts aren’t rated yet.
In the paper
“The alkali salt aerosols condense onto the heating surface of boilers to form a “sticky initial layer”.”
What the sources say
- Not checked — no full text of the sourcecites [7] M. Broström, S. Enestam, R. Backman, and K. Mäkelä, Fuel Processing Technology 105, 142 (2013 ). https://doi.org/10.1016/j.fuproc.2011.08.006. source
- Not checked — no full text of the sourcecites [8] X. Jin, J. Ye, L. Deng, and D. Che, Energy & Fuels 31, 2951 (2017). https://doi.org/10.1021/acs.energyfuels.6b03381. source
- Supportedcites [9] H. Zhang, C. Yu, and Z. Luo, RSC Advances 10, 21420 (2020). https://doi.org/10.1039/D0RA04370B. source
The Introduction says KCl and K₂SO₄ deposit on boiler superheaters mainly through condensation and thermophoresis, forming an innermost layer. The KCl condensation section describes a condensed KCl layer as sticky and able to capture fly ash. In this boiler, the authors observed a thin particle deposit before substantial KCl condensation, but that does not negate the broader statement attributed to the paper. (LLM, conf=0.87)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“For example, potassium sulphate (K2SO4) and sodium sulphate (Na2SO4) have been reported to cause insignificant damage after high temperature corrosion exposure if the protective oxidation scale of boiler steel remains intact and protective [18, 19].”
What the sources say
- Partly supportedcites [18] J. Pettersson, N. Folkeson, L.-G. Johansson, and J.-E. Svensson, Oxidation of Metals 76, 93 (2011). https://doi.org/10.1007/s11085-011-9240-z. sourceExperimental — accuracy not yet measured
The Discussion and Conclusions (page numbers unavailable) report that K2SO4 did not accelerate corrosion of 304L stainless steel under the tested conditions and had little effect on corrosion rate or surface morphology. The paper does not address Na2SO4, so it cannot support the claim about both sulphates. (LLM, conf=0.88)
- Not checked — no full text of the sourcecites [19] G. H. Meier, Oxidation of Metals 98, 1 (2022). https://doi.org/10.1007/s11085-020-10015-6. source
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Alloying element such as aluminium in nickel-based HVOF coatings also produces a protective layer of Al2O3 against corrosion attacks in both laboratory-scale and boiler environments [91, 104].”
What the sources say
- Not checked — no full text of the sourcecites [91] R. A. Mahesh, R. Jayaganthan, and S. Prakash, Surface Engineering 26, 413 (2010). https://doi.org/10.1179/174329409X451164. source
- Partly supportedcites [104] M. Bai, L. Reddy, and T. Hussain, Corrosion Science 135, 147 (2018). https://doi.org/10.1016/j.corsci.2018.02.047. sourceExperimental — accuracy not yet measured
Our copy supports the core of the claim for this source: Section 3.4 states 'the stainless steel was well protected by the deposition of NiAl coating with the formation of stable Al2O3 throughout the coatings', and Section 4.4 adds that 'chlorine was not able to further penetrate the Al2O3 scale at the coating/substrate interface, which ultimately protected the steel underneath from corrosion attack' for HVOF-sprayed β-NiAl on 304 steel. However, the evidence is a laboratory tube-furnace test (250 h, 700 °C, 500 ppm HCl in 5% O2/N2 with 10 wt% KCl deposit; Section 2.3 notes the gas is a 'simplified flue gas composition in biomass-fired boilers' and the setup was only 'designed based on industrial benchmark tests'), so the 'boiler environments' half of the claim — actual in-boiler exposure — is not demonstrated by this paper, which cites others for real boiler exposures (e.g. its refs 3, 6, 7, 12, 13). The paper also qualifies the protectiveness, noting severe corrosion initiating at uncoated sample edges, Al depletion and transformation to γ'-Ni3Al at the coating/steel interface after long-term service, and that temperatures below 700 °C 'may not be high enough to obtain a protective scale'. (LLM, conf=0.78)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Moreover, SPS offers a less complex approach to produce coatings that may potentially alter the wettability of molten ash particles in boilers compared to similar coating prepared by plasma spray physical vapour deposition (PS-PVD) [166].”
What the sources say
- Partly supportedcites [166] Y. Guo, et al., Advanced Science 10, 2205156 (2023). https://doi.org/10.1002/advs.202205156. sourceExperimental — accuracy not yet measured
The Conclusions (page unavailable) report that PS-PVD coatings can repel molten silicate, supporting the coating-wettability aspect of the claim. The paper does not assess SPS, compare its complexity with PS-PVD, or study ash particles in boilers; its stated application is turbine-engine coatings. (LLM, conf=0.84)
hedgedstates a possible cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Nickel-based alloys are among the most widely used materials for high temperature corrosion-resistant HVOF coatings, as summarised in Table 4.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
62 more claims
Create a free account to see all 145 claims and to verify the 11 references still open.
- It may state two separate claims as one. 47
- Probably not a substantial claim. 38
- Borderline: one of the tests for a substantial claim is unclear. 1
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Introduction
“The results showed that the use of low surface energy coatings such as h-BN reduces the contact angle of the molten ash in comparison with the surface of a bare steel.”
§ Introduction
“Thus, the poor wettability and reduced contact interface weakens the adhesion of the ash that accumulates on the boiler surface, and eventually, the slag will shed of its own accord owing to poor adhesion.”
Cited works that were retracted
Works this paper cites that were later retracted, from the retraction notices publishers deposit. Major when the notice came out before this paper was published.
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
“G. Singh, S. Kumar, and R. Kumar, Materials Research Express 7, 026527 (2020). https://doi.org/10.1088/2053-1591/ab6e7e. Article CAS Google Scholar”
Cited work 10.1088/2053-1591/ab6e7e · retracted 2021-01-13 · notice 10.1088/2053-1591/abd06a · this paper published 2024-07-10
Citations
Cites
1 retracted
Singh, G., Kumar, S., & Kumar, R. (2020) · Materials Research Express · doi:10.1088/2053-1591/ab6e7e · Cited by 21
RetractedBhushan, B., & Jung, Y. C. (2011) · Progress in Materials Science · doi:10.1016/j.pmatsci.2010.04.003 · Cited by 1,989
Niu, Y., Tan, H., & Hui, S. (2016) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2015.09.003 · Cited by 1,069
Fauchais, P. (2004) · Journal of Physics D: Applied Physics · doi:10.1088/0022-3727/37/9/r02 · Cited by 777
Cold spray coating: review of material systems and future perspectives
Moridi, A., Hassani-Gangaraj, S. M., Guagliano, M., & Dao, M. (2014) · Surface Engineering · doi:10.1179/1743294414y.0000000270 · Cited by 754
Grabke, H. J., Reese, E., & Spiegel, M. (1995) · Corrosion Science · doi:10.1016/0010-938x(95)00011-8 · Cited by 537
Geological survey professional paper 372. 1962
(1965) · Journal of Hydrology · doi:10.1016/0022-1694(65)90048-x · Cited by 504
Yuan, W., Li, R., Chen, Z., Gu, J., & Tian, Y. (2021) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2020.126582 · Cited by 363
High temperature corrosion of coatings and boiler steels below chlorine-containing salt deposits
Uusitalo, M. A., Vuoristo, P. M. J., & Mäntylä, T. A. (2004) · Corrosion Science · doi:10.1016/j.corsci.2003.09.026 · Cited by 260
Column Formation in Suspension Plasma-Sprayed Coatings and Resultant Thermal Properties
VanEvery, K., Krane, M. J. M., Trice, R. W., Wang, H., Porter, W., Besser, M., Sordelet, D., Ilavsky, J., & Almer, J. (2011) · Journal of Thermal Spray Technology · doi:10.1007/s11666-011-9632-2 · Cited by 253
Shen, F., Tao, W., Li, L., Zhou, Y., Wang, W., & Wang, S. (2020) · Applied Surface Science · doi:10.1016/j.apsusc.2020.146085 · Cited by 193
KCl Induced Corrosion of a 304-type Austenitic Stainless Steel at 600°C; The Role of Potassium
Pettersson, J., Asteman, H., Svensson, J. E., & Johansson, L. G. (2005) · Oxidation of Metals · doi:10.1007/s11085-005-5704-3 · Cited by 182
Steel Heat Treating Fundamentals and Processes
(2013) · ASM International eBooks · doi:10.31399/asm.hb.v04a.9781627081658 · Cited by 176
Thermally sprayed coatings resistant to erosion and corrosion for power plant boilers - A review
Szymański, K., Hernas, A., Moskal, G., & Myalska, H. (2015) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2014.10.046 · Cited by 172
EHLA: Extreme High‐Speed Laser Material Deposition
Schopphoven, T., Gasser, A., & Backes, G. (2017) · Laser Technik Journal · doi:10.1002/latj.201700020 · Cited by 142
Chatha, S. S., Sidhu, H. S., & Sidhu, B. S. (2012) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2012.01.060 · Cited by 132
Coatings for Automotive Gray Cast Iron Brake Discs: A Review
Aranke, O., Algenaid, W., Awe, S. A., & Joshi, S. V. (2019) · Coatings · doi:10.3390/coatings9090552 · Cited by 130
Accelerated hot corrosion studies of cold spray Ni–50Cr coating on boiler steels
Bala, N., Singh, H., & Prakash, S. (2010) · Materials & Design · doi:10.1016/j.matdes.2009.06.033 · Cited by 128
Development and analysis of thermal barrier coatings on gas turbine blades – A Review
Sahith, M. S., Giridhara, G., & Kumar, R. S. (2018) · Materials Today Proceedings · doi:10.1016/j.matpr.2018.01.060 · Cited by 124
Niu, Y., Zhu, Y., Tan, H., Hui, S., Jing, Z., & Xu, W. (2014) · Fuel Processing Technology · doi:10.1016/j.fuproc.2014.07.038 · Cited by 121
Pettersson, J., Folkeson, N., Johansson, L.-G., & Svensson, J.-E. (2011) · Oxidation of Metals · doi:10.1007/s11085-011-9240-z · Cited by 117
Condensation in the KCl–NaCl system
Broström, M., Enestam, S., Backman, R., & Mäkelä, K. (2013) · Fuel Processing Technology · doi:10.1016/j.fuproc.2011.08.006 · Cited by 113
Molten‐Volcanic‐Ash‐Phobic Thermal Barrier Coating based on Biomimetic Structure
Guo, Y., Song, W., Guo, L., Li, X., He, W., Yan, X., Dingwell, D. B., & Guo, H. (2023) · Advanced Science · doi:10.1002/advs.202205156 · Cited by 112
Developing hydrophobic and superhydrophobic TiO2 coatings by plasma spraying
Sharifi, N., Pugh, M., Moreau, C., & Dolatabadi, A. (2016) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2016.01.029 · Cited by 111
What Do We Know, What are the Current Limitations of Suspension Plasma Spraying?
Fauchais, P., Vardelle, M., Vardelle, A., & Goutier, S. (2015) · Journal of Thermal Spray Technology · doi:10.1007/s11666-015-0286-3 · Cited by 106
Kumar, S., Kumar, M., & Handa, A. (2020) · Materials at High Temperatures · doi:10.1080/09603409.2020.1810922 · Cited by 101
Ge, T., Chen, L., Gu, P., et al. (2022) · Optics & Laser Technology · doi:10.1016/j.optlastec.2022.107919 · Cited by 100
Introduction to thermal spray coatings
Espallargas, N. (2015) · Elsevier eBooks · doi:10.1016/b978-0-85709-769-9.00001-4 · Cited by 100
Kamal, S., Jayaganthan, R., & Prakash, S. (2008) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2008.04.087 · Cited by 92
Shi, M., Xue, Z., Zhang, Z., et al. (2020) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2020.125913 · Cited by 87
Chen, L., Zhang, X., Wu, Y., Chen, C., Li, Y., Zhou, W., & Ren, X. (2022) · Corrosion Science · doi:10.1016/j.corsci.2022.110271 · Cited by 85
Advanced Plasma Spray Applications
(2012) · doi:10.5772/1921 · Cited by 81
Bai, M., Reddy, L., & Hussain, T. (2018) · Corrosion Science · doi:10.1016/j.corsci.2018.02.047 · Cited by 81
Dorfman, M. (2018) · Elsevier eBooks · doi:10.1016/b978-0-323-52472-8.00023-x · Cited by 80
Karlsson, S., Åmand, L.-E., & Liske, J. (2015) · Fuel · doi:10.1016/j.fuel.2014.09.007 · Cited by 79
Oksa, M., Auerkari, P., Salonen, J., & Varis, T. (2014) · Fuel Processing Technology · doi:10.1016/j.fuproc.2014.04.006 · Cited by 78
Axial suspension plasma spraying of Al2O3 coatings for superior tribological properties
Goel, S., Björklund, S., Curry, N., et al. (2017) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2017.02.025 · Cited by 77
Hot corrosion behavior of HVOF-sprayed Cr 3 C 2 -WC-NiCoCrMo coating
Zhou, W., Zhou, K., Deng, C., Zeng, K., & Li, Y. (2017) · Ceramics International · doi:10.1016/j.ceramint.2017.04.109 · Cited by 77
Li, L., Shen, F., Zhou, Y., & Tao, W. (2019) · Journal of Laser Applications · doi:10.2351/1.5094378 · Cited by 76
Kumar, S., Kumar, M., & Handa, A. (2019) · Materials Research Express · doi:10.1088/2053-1591/ab5fae · Cited by 74
Wang, L., Skjevrak, G., Hustad, J. E., & Grønli, M. G. (2011) · Energy & Fuels · doi:10.1021/ef2007722 · Cited by 72
Erosion of thermal spray MCr–Cr3C2 cermet coatings
Stein, K. J., Schorr, B. S., & Marder, A. R. (1999) · Wear · doi:10.1016/s0043-1648(98)00298-1 · Cited by 71
Bala, N., Singh, H., & Prakash, S. (2009) · Journal of Thermal Spray Technology · doi:10.1007/s11666-009-9437-8 · Cited by 67
Bala, N., Singh, H., Prakash, S., & Karthikeyan, J. (2012) · Journal of Thermal Spray Technology · doi:10.1007/s11666-011-9698-x · Cited by 63
The effects of post-treatment on the hot corrosion behavior of the HVOF-sprayed Cr3C2–NiCr coating
Chatha, S. S., Sidhu, H. S., & Sidhu, B. S. (2012) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2012.04.026 · Cited by 62
Sokołowski, P., Pawłowski, L., Dietrich, D., et al. (2015) · Journal of Thermal Spray Technology · doi:10.1007/s11666-015-0310-7 · Cited by 62
Kawahara, Y. (2016) · Coatings · doi:10.3390/coatings6030034 · Cited by 62
Hot corrosion behaviour of HVOF-sprayed Cr 3 C 2 -NiCrMoNbAl coating
Zhou, W., Zhou, K., Deng, C., Zeng, K., & Li, Y. (2017) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2016.10.076 · Cited by 62
Ash fusion characteristics of biomass pellets during combustion
Zhai, M., Li, X., Yang, D., Ma, Z., & Dong, P. (2022) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2022.130361 · Cited by 61
High-Temperature Behavior of a High-Velocity Oxy-Fuel Sprayed Cr3C2-NiCr Coating
Kaur, M., Singh, H., & Prakash, S. (2012) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-012-1118-4 · Cited by 58
Mishra, S. B., Chandra, K., & Prakash, S. (2013) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2012.09.044 · Cited by 56
Short Review on the Origin and Countermeasure of Biomass Slagging in Grate Furnace
Zhu, Y., Niu, Y., Tan, H., & Wang, X. (2014) · Frontiers in Energy Research · doi:10.3389/fenrg.2014.00007 · Cited by 54
Performance of cold sprayed Ni based coatings in actual boiler environment
Bala, N., Singh, H., & Prakash, S. (2017) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2016.11.075 · Cited by 53
Paul, S., & Harvey, M. D. F. (2013) · Journal of Thermal Spray Technology · doi:10.1007/s11666-012-9820-8 · Cited by 52
Control of ash deposition in pulverized coal fired boiler
Naganuma, H., Ikeda, N., Kawai, T., Takuwa, T., Ito, T., Igarashi, Y., Yoshiie, R., & Naruse, I. (2008) · Proceedings of the Combustion Institute · doi:10.1016/j.proci.2008.06.001 · Cited by 52
Mohammadi, M., Kobayashi, A., Javadpour, S., & Jahromi, S. A. J. (2018) · Vacuum · doi:10.1016/j.vacuum.2018.04.042 · Cited by 52
Xu, X., Du, J., Luo, K., et al. (2021) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2021.127500 · Cited by 52
The corrosion behaviours of plasma-sprayed Fe-based amorphous coatings
Jiang, C., Liu, W., Wang, G., Chen, Y., Xing, Y., Zhang, C., & Dargusch, M. S. (2017) · Surface Engineering · doi:10.1080/02670844.2017.1319647 · Cited by 51
Hulka, I., Uțu, I. D., Avram, D., Dan, M. L., Pascu, A., Stanciu, E. M., & Roată, I. C. (2021) · Materials · doi:10.3390/ma14195583 · Cited by 49
Li, X., Liu, Z., Li, H., Wang, Y., & Bin, L. (2013) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2013.06.048 · Cited by 48
Singh, G., Bala, N., Chawla, V., & Singla, Y. K. (2021) · Corrosion Science · doi:10.1016/j.corsci.2021.109666 · Cited by 48
Future Development of Thermal Spray Coatings
(2015) · Elsevier eBooks · doi:10.1016/c2013-0-16360-x · Cited by 48
Mlonka-Mędrala, A., Gołombek, K., Buk, P., Cieślik, E., & Nowak, W. (2019) · Energy · doi:10.1016/j.energy.2019.116062 · Cited by 46
Innovations in laser cladding and direct laser metal deposition
Leyens, C., & Beyer, E. (2014) · Elsevier eBooks · doi:10.1016/b978-1-78242-074-3.00008-8 · Cited by 44
Kaur, M., Singh, H., & Prakash, S. (2009) · Surface Engineering · doi:10.1179/026708409x12490360425963 · Cited by 43
Meier, G. H. (2022) · Oxidation of Metals · doi:10.1007/s11085-020-10015-6 · Cited by 43
Sidhu, V. P. S., Goyal, K., & Goyal, R. (2017) · Australian Journal of Mechanical Engineering · doi:10.1080/14484846.2017.1364834 · Cited by 42
Improving hot corrosion resistance of Cr 3 C 2 –20NiCr coatings with CNT reinforcements
Goyal, K., & Goyal, R. (2020) · Surface Engineering · doi:10.1080/02670844.2019.1662645 · Cited by 42
Chatha, S. S., Sidhu, H. S., & Sidhu, B. S. (2013) · Journal of Thermal Spray Technology · doi:10.1007/s11666-013-9899-6 · Cited by 41
Kaushal, G., Bala, N., Kaur, N., Singh, H., & Prakash, S. (2014) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-013-1984-4 · Cited by 39
Thermal barrier coatings with novel architectures for diesel engine applications
de Góes, W. U., Markocsan, N., Gupta, M., et al. (2020) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2020.125950 · Cited by 39
Bhatia, R., Singh, H., & Sidhu, B. S. (2013) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-013-0771-0 · Cited by 38
Reduction mechanisms of ash deposition in coal and/or biomass combustion boilers
Naganuma, H., Ikeda, N., Ito, T., Matsuura, M., Nunome, Y., Ueki, Y., Yoshiie, R., & Naruse, I. (2013) · Fuel · doi:10.1016/j.fuel.2012.11.017 · Cited by 38
Characterization of Cold-Sprayed IN625 and NiCr Coatings
Srinivasan, D., Chandrasekhar, V., Amuthan, R., et al. (2016) · Journal of Thermal Spray Technology · doi:10.1007/s11666-016-0382-z · Cited by 37
Condensation Behaviors of Potassium during Biomass Combustion
Jin, X., Ye, J., Deng, L., & Che, D. (2017) · Energy & Fuels · doi:10.1021/acs.energyfuels.6b03381 · Cited by 37
Elevated-temperature corrosion of uncoated and aluminized 9–12% Cr boiler steels beneath KCl deposit
Metsäjoki, J., Huttunen‐Saarivirta, E., & Lepistö, T. K. (2014) · Fuel · doi:10.1016/j.fuel.2014.05.017 · Cited by 36
Kaushal, G., Singh, H., & Prakash, S. (2011) · Oxidation of Metals · doi:10.1007/s11085-011-9245-7 · Cited by 35
Mohammed, A. A., Khodair, Z. T., & Khadom, A. A. (2020) · Ceramics International · doi:10.1016/j.ceramint.2020.07.172 · Cited by 35
Control of ash deposition in solid fuel fired boiler
Naganuma, H., Ikeda, N., Ito, T., Satake, H., Matsuura, M., Ueki, Y., Yoshiie, R., & Naruse, I. (2013) · Fuel Processing Technology · doi:10.1016/j.fuproc.2011.09.009 · Cited by 34
Mahesh, R. A., Jayaganthan, R., & Prakash, S. (2010) · Surface Engineering · doi:10.1179/174329409x451164 · Cited by 34
Kumar, M., Singh, H., Singh, N., & Joshi, R. S. (2015) · Wear · doi:10.1016/j.wear.2015.01.043 · Cited by 32
Microstructure and mechanical properties of thermal sprayed nanostructured Cr3C2-Ni20Cr coatings
da Cunha, C. A., de Lima, N. B., Martinelli, J. R., et al. (2008) · Materials Research · doi:10.1590/s1516-14392008000200005 · Cited by 32
Fundamentals of Cold Spray Processing: Evolution and Future Perspectives
AlMangour, B. (2017) · Springer eBooks · doi:10.1007/978-3-319-67183-3_1 · Cited by 32
Fireside corrosion on T24 steel pipes and HVOF NiCr coatings exposed to different salt mixtures
Abu-warda, N., López, A. J., Pedraza, F., & Utrilla, M. V. (2020) · Corrosion Science · doi:10.1016/j.corsci.2020.108747 · Cited by 32
Cheng, J., Wu, Y., Shen, W. D., Hong, S., Qiao, L., & Wang, Y. (2020) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2020.126015 · Cited by 32
Singh, H., Bala, N., Kaur, N., Sharma, S. K., Kim, D. Y., & Prakash, S. (2015) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2015.08.002 · Cited by 31
Erosion–corrosion behaviour of Ni–20Cr plasma coating in actual boiler environment
Mishra, S. B., & Prakash, S. (2015) · Surface Engineering · doi:10.1179/1743294414y.0000000338 · Cited by 31
Thermal Spray Coatings for High-Temperature Corrosion Protection in Biomass Co-Fired Boilers
Oksa, M., Metsäjoki, J., & Kärki, J. (2014) · Journal of Thermal Spray Technology · doi:10.1007/s11666-014-0155-5 · Cited by 31
Wang, R., Ouyang, C., Li, Q., et al. (2022) · Materials · doi:10.3390/ma15051643 · Cited by 31
Saladi, S., Menghani, J. V., & Prakash, S. (2015) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-015-1400-x · Cited by 29
Rani, A., Bala, N., & Gupta, C. M. (2017) · Oxidation of Metals · doi:10.1007/s11085-017-9759-8 · Cited by 28
High-temperature sulfur corrosion behavior of h-BN-based ceramic coating prepared by slurry method
Wang, J., Yuan, Y., Chi, Z., & Zhang, G. (2017) · Materials Chemistry and Physics · doi:10.1016/j.matchemphys.2017.12.025 · Cited by 28
Development and application of anti-fouling ceramic coating for high-sodium coal-fired boilers
Wang, J., Yuan, Y., Chi, Z., & Zhang, G. (2018) · Journal of the Energy Institute · doi:10.1016/j.joei.2017.08.003 · Cited by 27
Laxminarayan, Y., Nair, A. B., Jensen, P. A., Wu, H., Frandsen, F., Sander, B., & Glarborg, P. (2018) · Energy & Fuels · doi:10.1021/acs.energyfuels.7b03114 · Cited by 27
Oksa, M., Varis, T., & Ruusuvuori, K. (2014) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2014.04.025 · Cited by 26
Slurry spray coating of carbon steel for use in oxidizing and humid environments
Nguyen, M. D., Bang, J. W., Kim, Y. H., Bin, A. S., Hwang, K. H., Pham, V., & Kwon, W. T. (2018) · Ceramics International · doi:10.1016/j.ceramint.2018.02.017 · Cited by 26
The Microstructure of Weld Overlay Ni-Base Alloy Deposited on Carbon Steel by CMT Method
Solecka, M., Petrzak, P., & Radziszewska, A. E. (2015) · Diffusion and defect data, solid state data. Part B, Solid state phenomena/Solid state phenomena · doi:10.4028/www.scientific.net/ssp.231.119 · Cited by 25
Singh, V., Goyal, K., & Goyal, R. (2019) · Anti-Corrosion Methods and Materials · doi:10.1108/acmm-10-2018-2009 · Cited by 25
Continuous KCl addition in high temperature exposures of 304 L – A way to mimic a boiler environment
Phother-Simon, J., Jonsson, T., & Liske, J. (2020) · Corrosion Science · doi:10.1016/j.corsci.2020.108511 · Cited by 25
Study of Corrosion in a Biomass Boiler
Berlanga, C., & Ruiz, J. A. (2013) · Journal of Chemistry · doi:10.1155/2013/272090 · Cited by 23
Saladi, S., Menghani, J. V., & Prakash, S. (2014) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-014-1240-0 · Cited by 23
Deposit Shedding in Biomass-Fired Boilers: Shear Adhesion Strength Measurements
Laxminarayan, Y., Jensen, P. A., Wu, H., Frandsen, F. J., Sander, B., & Glarborg, P. (2017) · Energy & Fuels · doi:10.1021/acs.energyfuels.7b01312 · Cited by 23
Xiao, K., Xue, W. C., Li, Z., et al. (2018) · Ceramics International · doi:10.1016/j.ceramint.2018.03.147 · Cited by 23
Gada, H., Mudgal, D., Parvez, S., & Ahmad, B. (2019) · Engineering Failure Analysis · doi:10.1016/j.engfailanal.2019.104256 · Cited by 23
Alnaser, I. A., Yunus, M., Alfattani, R., & Alamro, T. (2021) · Materials · doi:10.3390/ma14185119 · Cited by 23
Goyal, A., Singh, R., & Singh, G. (2017) · Materials Today Proceedings · doi:10.1016/j.matpr.2017.01.007 · Cited by 22
Bala, N., Singh, H., Karthikeyan, J., & Prakash, S. (2013) · Materials and Corrosion · doi:10.1002/maco.201106387 · Cited by 21
Kaushal, G., Singh, H., & Prakash, S. (2011) · Materials at High Temperatures · doi:10.3184/096034011x12960473417949 · Cited by 20
Hot Corrosion Behavior of Arc-Sprayed Highly Dense NiCr-Based Coatings in Chloride Salt Deposit
Qin, E., Song, Y., Ji, H. W., Huang, Q., Liu, Z., & Wu, S. (2017) · Journal of Thermal Spray Technology · doi:10.1007/s11666-017-0549-2 · Cited by 19
Mishra, S. B., Chandra, K., & Prakash, S. (2017) · Anti-Corrosion Methods and Materials · doi:10.1108/acmm-11-2015-1592 · Cited by 19
Hot corrosion behavior of wire-arc sprayed NiCrB coatings
Wang, X., He, D., Guo, X., Zhou, Z., Wang, G., & Guo, F. (2019) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2019.03.058 · Cited by 19
Electron Microscopy Investigation of Inconel 625 Weld Overlay on Boiler Steel
Petrzak, P., Blicharski, M., Dymek, S., et al. (2015) · Diffusion and defect data, solid state data. Part B, Solid state phenomena/Solid state phenomena · doi:10.4028/www.scientific.net/ssp.231.113 · Cited by 18
Thermal spray coatings in renewable energy applications
Wijewardane, S. (2015) · Elsevier eBooks · doi:10.1016/b978-0-85709-769-9.00010-5 · Cited by 18
Corrosion Testing of Thermal Spray Coatings in a Biomass Co-Firing Power Plant
Oksa, M., Metsäjoki, J., & Kärki, J. (2016) · Coatings · doi:10.3390/coatings6040065 · Cited by 17
Kumar, M., Singh, H., Singh, N., Chavan, N. M., Kumar, S., & Joshi, S. V. (2015) · Journal of Thermal Spray Technology · doi:10.1007/s11666-015-0249-8 · Cited by 16
Anti-Fouling Ceramic Coating for Improving the Energy Efficiency of Steel Boiler Systems
Nguyen, M., Bang, J., Kim, Y., Bin, A., Hwang, K., Pham, V.-H., & Kwon, W.-T. (2018) · Coatings · doi:10.3390/coatings8100353 · Cited by 16
Khantisopon, K., Tharajak, J., Nawarat, P., Sanpo, N., & Ang, A. S. M. (2022) · Corrosion Science · doi:10.1016/j.corsci.2022.110470 · Cited by 16
Self-citationRani, A., Bala, N., & Gupta, C. M. (2017) · Anti-Corrosion Methods and Materials · doi:10.1108/acmm-09-2016-1712 · Cited by 15
Lyophobicity and slagging resistance mechanism of h-BN based coating for coal-fired boilers
Wang, J., Zhang, G., Li, F., & Chi, Z. (2019) · Fuel Processing Technology · doi:10.1016/j.fuproc.2019.02.012 · Cited by 15
Future trends in cold spray techniques
Huang, R., & FUKANUMA, H. (2015) · Elsevier eBooks · doi:10.1016/b978-0-85709-769-9.00006-3 · Cited by 14
Kaushal, G., Singh, H., & Prakash, S. (2012) · Journal of Thermal Spray Technology · doi:10.1007/s11666-012-9770-1 · Cited by 14
Adhesion strength optimization of slurry sprayed mullite-based coating using Taguchi method
Verma, R., Kant, S., & Suri, N. M. (2015) · Proceedings of the Institution of Mechanical Engineers Part E Journal of Process Mechanical Engineering · doi:10.1177/0954408915595948 · Cited by 14
The Effect of Temperature on the Formation of Oxide Scales Regarding Commercial Superheater Steels
Lehmusto, J., Lindberg, D., Yrjas, P., & Hupa, L. (2017) · Oxidation of Metals · doi:10.1007/s11085-017-9785-6 · Cited by 14
Wu, D., Liu, S., Yuan, Z., Cao, P., Wei, X., & Zhang, C. (2021) · Journal of Thermal Spray Technology · doi:10.1007/s11666-021-01248-1 · Cited by 14
Sundararajan, G., Rao, D. S., Sivakumar, G., et al. (2013) · Springer eBooks · doi:10.1007/978-0-387-92897-5_704 · Cited by 14
Kung, S. C. (2015) · Corrosion · doi:10.5006/1409 · Cited by 13
Hot Corrosion Behavior and Mechanism of High-Velocity Arc-Sprayed Ni-Cr Alloy Coatings
Cheng, J., Wu, Y., Chen, L., Hong, S., Qiao, L., & Wei, Z. (2019) · Journal of Thermal Spray Technology · doi:10.1007/s11666-019-00890-0 · Cited by 13
Utilization of ball-milled powders for surface protective coating
El-Eskandarany, M. S. (2020) · Elsevier eBooks · doi:10.1016/b978-0-12-818180-5.00012-1 · Cited by 13
Zhang, H., Yu, C., & Luo, Z. (2020) · RSC Advances · doi:10.1039/d0ra04370b · Cited by 13
Sundaresan, C., Rajasekaran, B., Sivakumar, G., & Rao, D. S. (2020) · IOP Conference Series: Materials Science and Engineering · doi:10.1088/1757-899x/872/1/012092 · Cited by 13
Evaluation of corrosion mechanism for tungsten carbide coating exposed in actual boiler environment
Saroop, V., Mudgal, D., Kumar, S., et al. (2020) · Engineering Failure Analysis · doi:10.1016/j.engfailanal.2020.104905 · Cited by 13
Periodic Mesoporous Materials: Holes Filled with Opportunities
Bonifácio, L. D. S., Lotsch, B. V., & Ozin, G. A. (2010) · Elsevier eBooks · doi:10.1016/b978-0-12-374396-1.00049-0 · Cited by 12
Tailor, S., Vashishtha, N., Modi, A., et al. (2019) · Materials Research Express · doi:10.1088/2053-1591/ab1947 · Cited by 12
Okoro, S. C., Kvisgaard, M., Montgomery, M., Frandsen, F., & Pantleon, K. (2016) · Surface Engineering · doi:10.1080/02670844.2016.1199128 · Cited by 11
High-Temperature Corrosion of Ni-Base Alloys by Waste Incineration Ashes
Solecka, M., Kusinski, J. P., Kopia, A., et al. (2016) · Acta Physica Polonica A · doi:10.12693/aphyspola.130.1045 · Cited by 11
Pre-oxidation as a Means to Increase Corrosion Resistance of Commercial Superheater Steels
Lehmusto, J., Yrjas, P., & Hupa, L. (2019) · Oxidation of Metals · doi:10.1007/s11085-019-09898-x · Cited by 11
Nicholls, J. R., Long, K. A., & Simms, N. J. (2009) · Elsevier eBooks · doi:10.1016/b978-044452787-5.00176-1 · Cited by 11
Kahl, B. A., Berndt, C. C., & Ang, A. S. M. (2021) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2021.127128 · Cited by 11
Self-citationHigh-Temperature Oxidation and Smelt Deposit Corrosion of Ni-Cr-Ti Arc-Sprayed Coatings
Matthews, S. J., & Schweizer, M. (2013) · Journal of Thermal Spray Technology · doi:10.1007/s11666-013-9939-2 · Cited by 10
Surface Engineering Analysis of D-Gun Sprayed Cermet Coating in Aggressive Environment
Shukla, V. N., Trivedi, H., Kumar, H., et al. (2017) · Materials Today Proceedings · doi:10.1016/j.matpr.2017.06.350 · Cited by 9
Park, J. H., Lee, D.-H., Han, K.-H., Shin, J.-S., Bae, D.-H., Shim, T.-E., Lee, J. H., & Shun, D. (2019) · Fuel · doi:10.1016/j.fuel.2018.09.020 · Cited by 9
Krumm, L., & Galetz, M. C. (2020) · Materials and Corrosion · doi:10.1002/maco.201911091 · Cited by 8
Erosion Characteristics of HVOF Developed Cr3C2-NiCr and WC-Co Coatings
Singh, H., & Sidhu, B. S. (2013) · Materials science forum · doi:10.4028/www.scientific.net/msf.751.71 · Cited by 7
Talus, A., Alipour, Y., Norling, R., & Henderson, P. (2016) · Materials and Corrosion · doi:10.1002/maco.201508693 · Cited by 7
Effects of Ash Deposition and Slagging on Heat Transfer
Zhang, Y., Li, Q., & Zhou, H. (2016) · Theory and Calculation of Heat Transfer in Furnaces · doi:10.1016/b978-0-12-800966-6.00006-5 · Cited by 7
Singh, H., Kalsi, S. S., & Sidhu, T. S. (2019) · Materials and Corrosion · doi:10.1002/maco.201911116 · Cited by 7
Mittal, R., Singh, M., & Kumar, P. (2019) · Materials Today Proceedings · doi:10.1016/j.matpr.2019.07.487 · Cited by 7
Degradation Studies of Wire arc Sprayed FeCrBSiMn Alloy Coating in Molten Salt Environment
Shukla, V. N., Rana, N., Jayaganthan, R., et al. (2014) · Procedia Engineering · doi:10.1016/j.proeng.2013.11.025 · Cited by 6
Hot Corrosion Behaviour of CNT Reinforced Zirconium Yttrium Coatings in Molten Salt Environment
Kumar, S., Bhatia, R., & Singh, H. (2020) · Journal of Bio- and Tribo-Corrosion · doi:10.1007/s40735-020-00378-3 · Cited by 6
Effect of surface roughness and surface energy on molten fly ash deposition
Balakrishnan, S., & Nagarajan, R. (2014) · International Journal of Advances in Engineering Sciences and Applied Mathematics · doi:10.1007/s12572-014-0108-8 · Cited by 5
Evaluation of the behavior of D-Gun sprayed coatings on T-11 boiler steel at 900 °C temperature
Mittal, R., & Singh, H. (2020) · Materials Today Proceedings · doi:10.1016/j.matpr.2019.12.136 · Cited by 5
Silva, C. C. (2013) · Springer eBooks · doi:10.1007/978-0-387-92897-5_708 · Cited by 5
Slurry spray technique for manufacturing thermal barrier coatings
Nguyen, P. T. T., Ho, S.-Y., & Kotousov, A. G. (2013) · Surface Innovations · doi:10.1680/si.12.00018 · Cited by 4
Fauchais, P. L., Heberlein, J. V. R., & Boulos, M. I. (2013) · Springer eBooks · doi:10.1007/978-0-387-68991-3_9 · Cited by 4
Gada, H., Mudgal, D., & Ahmad, B. (2019) · Journal of Physics Conference Series · doi:10.1088/1742-6596/1240/1/012129 · Cited by 4
Hurley, J. P. (2011) · Elsevier eBooks · doi:10.1533/9780857093806.5.575 · Cited by 3
Metsäjoki, J., Huttunen‐Saarivirta, E., & Lepistö, T. K. (2011) · High Temperature Materials and Processes · doi:10.1515/htmp.2011.027 · Cited by 3
A Study on Characterization of Biomass Fly Ash
Tharajak, J., & Sanpo, N. (2019) · Applied Mechanics and Materials · doi:10.4028/www.scientific.net/amm.891.137 · Cited by 3
Slagging resistance mechanism of precursor ceramic coating for solid fuel-fired boilers
Wang, G., Zhang, B., Wang, J., Chi, Z., Zhang, G., li, J., Wang, J., Qian, P., & Yang, S. (2020) · IOP Conference Series: Materials Science and Engineering · doi:10.1088/1757-899x/721/1/012023 · Cited by 3
Alkali silicate protective coatings
Нажарова, Л. Н., Мингазова, Г. Г., & Сайфуллин, Р. С. (2018) · IOP Conference Series Materials Science and Engineering · doi:10.1088/1757-899x/450/3/032003 · Cited by 2
Ansari, M. S., Bansal, A., Chawla, V., & Aggarwal, V. (2021) · Surface Topography: Metrology and Properties · doi:10.1088/2051-672x/ac0171 · Cited by 2
Performance of the Glass-Ceramic Coating Prepared by Slurry Spraying Technique
Hu, H. B., Yang, J. M., Fang, Z. Q., et al. (2013) · Advanced materials research · doi:10.4028/www.scientific.net/amr.779-780.47 · Cited by 1
Research works printed but not linked: 5
- J. J. Rowe, G. W. Morey, and C. S. Zen, Geological Survey Professional Paper 741, 1 (1972).
- P. Nguyen, S. Harding, and S. -Y. Ho, Experimental studies on slurry based thermal barrier coatings. in Proceedings of the 5th Australasian Congress on Applied Mechanics, (Engineers Australia, Brisbane, Qld, 2007), p. 545.
- W. F. Gale and T. C. Totemeier, 35.2 Chemical Vapour Deposition. in Smithells Metals Reference Book (8th Edition), (Elsevier. 2004).
- S. V. Joshi, D. Srinivasa Rao, and S. Centre for, N.-A. Technology of, and C. Other Developing, Surface Engineering, (Daya Publishing House, New Delhi, India, 2010). (in English).
- C. V. Maria, Sprays: Types, Technology and Modeling (Engineering Tools, Techniques and Tables), (Nova Science Publishers, Inc, New York, 2011). in English.
Cited by
Singh, A. N., Swain, S. K., Meena, A., et al. (2024) · Ceramics · doi:10.3390/ceramics7040121 · Cited by 24
“Within the next decade, we may expect the venture to discover a perfect material will come to see the light of the Sun and its applications in power plants and various high-temperature applications.”
Chen, H., Zhang, Z., Yin, S., Zhang, T., Song, T., & Lu, P. (2026) · Carbon Neutral Technologies · doi:10.1016/j.cnt.2026.100022 · Cited by 6
Wei, Z., Wang, L., Liang, X., Sharma, D., Zhu, H., Yuan, Z., & Wu, L. (2026) · Applied Energy · doi:10.1016/j.apenergy.2026.128092 · Cited by 7
Usman, A., Isern, L., Nicholls, J. R., Cordero-Cabrera, M. C., & Syed, A. U. (2025) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-025-11630-7 · Cited by 3
Ma, X., Zhu, J., Gao, C., et al. (2026) · Extreme Materials · doi:10.1016/j.exm.2026.01.002 · Cited by 2
Metadata
- Authors
- Khantisopon, K., Singh, S., Jitputti, J., Berndt, C. C., & Ang, A. S. M.
- Affiliations
- Australian Research Council (AU)
- SCG Chemicals (Thailand) (TH)
- Corresponding author
- Ang, Andrew S. M.
- Venue
- High Temperature Corrosion of Materials
- Published
- 2024-07-10
- Volume
- 101
- Issue
- S1
- Pages
- 1-55
- ISSN
- 2731-8397 (ISSN-L)
- 2731-8400
- OpenAlex
- W4400487032
- Cited by
- 30
- References
- 162
- Citations by year
- 2026: 20 · 2025: 9 · 2024: 1
- FWCI
- 0.70
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Licence
- cc-by
- creativecommons.org/licenses/by/4.0 (tdm)
- creativecommons.org/licenses/by/4.0 (vor)
- Locations
- High Temperature Corrosion of Materials (publishedVersion, cc-by)
- Funders
- ARC Industrial Transformation Training Centre (IC 180100005)
- Swinburne University of Technology
- Topics
- Physical Sciences › Materials Science › Surfaces, Coatings and Films › High-Temperature Coating Behaviors
- Physical Sciences › Engineering › Mechanical Engineering › Surface Treatment and Coatings
- Physical Sciences › Materials Science › Ceramics and Composites › Advanced ceramic materials synthesis
- Keywords
- high-temperature corrosion, corrosion protection coatings, biomass boiler, slag deposition, thermal spraying, atmospheric plasma spraying, HVOF spraying, detonation spraying, cold spray, ceramic-metal composites, fly ash deposition
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol and qwen3.8-omni-flash).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.