The DOI matches its Crossref record; 32 of the 32 references it cites were found in a registry or an index.
XCT analysis of the influence of melt strategies on defect population in Ti–6Al–4V components manufactured by Selective Electron Beam Melting
Open accessAbstract
Selective Electron Beam Melting (SEBM) is a promising powder bed Additive Manufacturing technique for near-net-shape manufacture of high-value titanium components. However without post-manufacture HIPing the fatigue life of SEBM parts is currently dominated by the presence of porosity. In this study, the size, volume fraction, and spatial distribution of the pores in model samples have been characterised in 3D, using X-ray Computed Tomography, and correlated to the process variables. The average volume fraction of the pores (< 0.2%) was measured to be lower than that usually observed in competing processes, such as selective laser melting, but a strong relationship was found with the different beam strategies used to contour, and infill by hatching, a part section. The majority of pores were found to be small spherical gas pores, concentrated in the infill hatched region; this was attributed to the lower energy density and less focused beam used in the infill strategy allowing less opportunity for gas bubbles to escape the melt pool. Overall, increasing the energy density or focus of the beam was found to correlate strongly to a reduction in the level of gas porosity. Rarer irregular shaped pores were mostly located in the contour region and have been attributed to a lack of fusion between powder particles.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
A Threshold Selection Method from Gray-Level Histograms
Otsu, N. (1979) · IEEE Transactions on Systems, Man, and Cybernetics · doi:10.1109/tsmc.1979.4310076 · Cited by 43,398
Metal Additive Manufacturing: A Review
Frazier, W. E. (2014) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-014-0958-z · Cited by 5,984
Additive Manufacturing Technologies: Rapid Prototyping to Direct Digital Manufacturing
Gibson, I., Rosen, D. W., & Stucker, B. (2010) · National University of Singapore · doi:10.1007/978-1-4419-1120-9 · Cited by 2,969
A study of the microstructural evolution during selective laser melting of Ti–6Al–4V
Thijs, L., Verhaeghe, F., Craeghs, T., Humbeeck, J. V., & Kruth, J.-P. (2010) · Acta Materialia · doi:10.1016/j.actamat.2010.02.004 · Cited by 2,929
Binding mechanisms in selective laser sintering and selective laser melting
Kruth, J., Mercelis, P., Van Vaerenbergh, J., Froyen, L., & Rombouts, M. (2005) · Rapid Prototyping Journal · doi:10.1108/13552540510573365 · Cited by 1,383
Maire, E., & Withers, P. J. (2014) · International Materials Reviews · doi:10.1179/1743280413y.0000000023 · Cited by 1,374
Peterson's Stress Concentration Factors
Pilkey, W. D. (1997) · Wiley eBooks · doi:10.1002/9780470172674 · Cited by 885
Al-Bermani, S. S., Blackmore, M., Zhang, W., & Todd, I. (2010) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-010-0397-x · Cited by 860
Self-citationQiu, C., Adkins, N. J. E., & Attallah, M. M. (2013) · Materials Science and Engineering: A · doi:10.1016/j.msea.2013.04.099 · Cited by 821
Heinl, P., Müller, L., Körner, C., Singer, R. F., & Müller, F. A. (2008) · Acta Biomaterialia · doi:10.1016/j.actbio.2008.03.013 · Cited by 815
Cited by
Additive manufacturing of metallic components – Process, structure and properties
DebRoy, T., Wei, H. L., Zuback, J. S., Mukherjee, T., Elmer, J. W., Milewski, J. O., Beese, A. M., Wilson-Heid, A., De, A., & Zhang, W. (2018) · Progress in Materials Science · doi:10.1016/j.pmatsci.2017.10.001 · Cited by 8,805
Additive manufacturing of Ti6Al4V alloy: A review
Liu, S., & Shin, Y. C. (2019) · Materials & Design · doi:10.1016/j.matdes.2018.107552 · Cited by 2,472
Aboulkhair, N. T., Simonelli, M., Parry, L., Ashcroft, I., Tuck, C., & Hague, R. (2019) · Progress in Materials Science · doi:10.1016/j.pmatsci.2019.100578 · Cited by 1,552
Review of in-situ process monitoring and in-situ metrology for metal additive manufacturing
Everton, S. K., Hirsch, M., Stravroulakis, P., Leach, R. K., & Clare, A. T. (2016) · Materials & Design · doi:10.1016/j.matdes.2016.01.099 · Cited by 1,469
Kok, Y., Tan, X. P., Wang, P., Nai, M. L. S., Loh, N. H., Liu, E., & Tor, S. B. (2018) · Materials & Design · doi:10.1016/j.matdes.2017.11.021 · Cited by 1,447
Additive manufacturing of metallic components by selective electron beam melting — a review
Körner, C. (2016) · International Materials Reviews · doi:10.1080/09506608.2016.1176289 · Cited by 1,106
Materials for additive manufacturing
Bourell, D., Kruth, J. P., Leu, M., Levy, G., Rosen, D., Beese, A. M., & Clare, A. (2017) · CIRP Annals · doi:10.1016/j.cirp.2017.05.009 · Cited by 1,034
Process defects and in situ monitoring methods in metal powder bed fusion: a review
Grasso, M., & Colosimo, B. M. (2017) · Measurement Science and Technology · doi:10.1088/1361-6501/aa5c4f · Cited by 833
“…2011; Gong, 2013; Read et al., 2015; Kruth et al., 2004; Weingarten et al., 2015; Thijs et al., 2010; Scharowsky et al., 2015; Puebla et al., 2012; Tammas-Williams et al., 2015; Biamino et al., 2011; Zeng, 2015 Li et al., 2012; Kruth et al., 2004; Tolochko et al., 2004; Zhou et al., 2015; Attar,…”
Chowdhury, S., Yadaiah, N., Prakash, C., Ramakrishna, S., Dixit, S., Gupta, L. R., & Buddhi, D. (2022) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2022.07.121 · Cited by 784
du Plessis, A., Yadroitsava, I., & Yadroitsev, I. (2020) · Materials & Design · doi:10.1016/j.matdes.2019.108385 · Cited by 712
Residual Stress in Metal Additive Manufacturing
Li, C., Liu, Z. Y., Fang, X. Y., & Guo, Y. B. (2018) · Procedia CIRP · doi:10.1016/j.procir.2018.05.039 · Cited by 708
Beretta, S., & Romano, S. (2017) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2016.06.020 · Cited by 635
du Plessis, A., Yadroitsev, I., Yadroitsava, I., & Le Roux, S. G. (2018) · 3D Printing and Additive Manufacturing · doi:10.1089/3dp.2018.0060 · Cited by 550
Powder Bed Fusion of nickel-based superalloys: A review
Sanchez, S., Smith, P., Xu, Z., Gaspard, G., Hyde, C. J., Wits, W. W., Ashcroft, I. A., Chen, H., & Clare, A. T. (2021) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2021.103729 · Cited by 541
Mechanistic models for additive manufacturing of metallic components
Wei, H. L., Mukherjee, T., Zhang, W., Zuback, J. S., Knapp, G. L., De, A., & DebRoy, T. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2020.100703 · Cited by 530
X-ray computed tomography for additive manufacturing: a review
Thompson, A., Maskery, I., & Leach, R. K. (2016) · Measurement Science and Technology · doi:10.1088/0957-0233/27/7/072001 · Cited by 521
The Influence of Porosity on Fatigue Crack Initiation in Additively Manufactured Titanium Components
Tammas-Williams, S., Withers, P. J., Todd, I., & Prangnell, P. B. (2017) · Scientific Reports · doi:10.1038/s41598-017-06504-5 · Cited by 494
Self-citationDefects and anomalies in powder bed fusion metal additive manufacturing
Mostafaei, A., Zhao, C., He, Y., Reza Ghiaasiaan, S., Shi, B., Shao, S., Shamsaei, N., Wu, Z., Kouraytem, N., Sun, T., et al. (2022) · Current Opinion in Solid State and Materials Science · doi:10.1016/j.cossms.2021.100974 · Cited by 491
Additive Manufacturing of Titanium Alloys by Electron Beam Melting: A Review
Zhang, L., Liu, Y., Li, S., & Hao, Y. (2018) · Advanced Engineering Materials · doi:10.1002/adem.201700842 · Cited by 486
Fatigue life of additively manufactured Ti–6Al–4V in the very high cycle fatigue regime
Günther, J., Krewerth, D., Lippmann, T., Leuders, S., Tröster, T., Weidner, A., Biermann, H., & Niendorf, T. (2017) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2016.05.018 · Cited by 475
Metal additive manufacturing: Technology, metallurgy and modelling
Cooke, S., Ahmadi, K., Willerth, S., & Herring, R. (2020) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2020.07.025 · Cited by 378
Fracture and fatigue in additively manufactured metals
Becker, T. H., Kumar, P., & Ramamurty, U. (2021) · Acta Materialia · doi:10.1016/j.actamat.2021.117240 · Cited by 377
Cunningham, R., Narra, S. P., Montgomery, C., Beuth, J., & Rollett, A. D. (2017) · JOM · doi:10.1007/s11837-016-2234-1 · Cited by 334
Defect structure process maps for laser powder bed fusion additive manufacturing
Gordon, J. V., Narra, S. P., Cunningham, R. W., Liu, H., Chen, H., Suter, R. M., Beuth, J. L., & Rollett, A. D. (2020) · Additive Manufacturing · doi:10.1016/j.addma.2020.101552 · Cited by 329
Yan, X., Yin, S., Chen, C., Huang, C., Bolot, R., Lupoi, R., Kuang, M., Ma, W., Coddet, C., Liao, H., et al. (2018) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2018.06.076 · Cited by 326
Maskery, I., Aboulkhair, N. T., Corfield, M. R., Tuck, C., Clare, A. T., Leach, R. K., Wildman, R. D., Ashcroft, I. A., & Hague, R. J. M. (2016) · Materials Characterization · doi:10.1016/j.matchar.2015.12.001 · Cited by 317
Defect characteristics and analysis of their variability in metal L-PBF additive manufacturing
Sanaei, N., Fatemi, A., & Phan, N. (2019) · Materials & Design · doi:10.1016/j.matdes.2019.108091 · Cited by 301
A literature review of powder-based electron beam melting focusing on numerical simulations
Galati, M., & Iuliano, L. (2018) · Additive Manufacturing · doi:10.1016/j.addma.2017.11.001 · Cited by 300
Tammas-Williams, S., Withers, P. J., Todd, I., & Prangnell, P. B. (2016) · Scripta Materialia · doi:10.1016/j.scriptamat.2016.05.002 · Cited by 288
Self-citationZhang, X. Z., Leary, M., Tang, H. P., Song, T., & Qian, M. (2018) · Current Opinion in Solid State and Materials Science · doi:10.1016/j.cossms.2018.05.002 · Cited by 285
Wang, S., Ning, J., Zhu, L., Yang, Z., Yan, W., Dun, Y., Xue, P., Xu, P., Bose, S., & Bandyopadhyay, A. (2022) · Materials Today · doi:10.1016/j.mattod.2022.08.014 · Cited by 279
Additive manufacturing and postprocessing of Ti-6Al-4V for superior mechanical properties
Qian, M., Xu, W., Brandt, M., & Tang, H. P. (2016) · MRS Bulletin · doi:10.1557/mrs.2016.215 · Cited by 275
Tammas-Williams, S., Withers, P. J., Todd, I., & Prangnell, P. B. (2016) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-016-3429-3 · Cited by 269
Self-citationQualification of AM parts: Extreme value statistics applied to tomographic measurements
Romano, S., Brandão, A., Gumpinger, J., Gschweitl, M., & Beretta, S. (2017) · Materials & Design · doi:10.1016/j.matdes.2017.05.091 · Cited by 269
Effects of process parameters on porosity in laser powder bed fusion revealed by X-ray tomography
du Plessis, A. (2019) · Additive Manufacturing · doi:10.1016/j.addma.2019.100871 · Cited by 264
Zerbst, U., Bruno, G., Buffière, J.-Y., Wegener, T., Niendorf, T., Wu, T., Zhang, X., Kashaev, N., Meneghetti, G., Hrabe, N., et al. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2021.100786 · Cited by 263
Cunningham, R., Nicolas, A., Madsen, J., Fodran, E., Anagnostou, E., Sangid, M. D., & Rollett, A. D. (2017) · Materials Research Letters · doi:10.1080/21663831.2017.1340911 · Cited by 259
Mitigation of lack of fusion defects in powder bed fusion additive manufacturing
Mukherjee, T., & DebRoy, T. (2018) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2018.10.028 · Cited by 256
Pegues, J. W., Shao, S., Shamsaei, N., Sanaei, N., Fatemi, A., Warner, D. H., Li, P., & Phan, N. (2020) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2019.105358 · Cited by 236
Sadeghi, E., Karimi, P., Momeni, S., Seifi, M., Eklund, A., & Andersson, J. (2019) · Materials Characterization · doi:10.1016/j.matchar.2019.02.016 · Cited by 74
Wang, P., Nai, M. L. S., Lu, S., Bai, J., Zhang, B., & Wei, J. (2017) · JOM · doi:10.1007/s11837-017-2610-5 · Cited by 37
Narra, S. P. (2022) · Encyclopedia of Materials: Metals and Alloys · doi:10.1016/b978-0-12-819726-4.00107-1 · Cited by 9
Metadata
- Authors
- Tammas-Williams, S., Zhao, H., Léonard, F., Derguti, F., Todd, I., & Prangnell, P. B.
- Venue
- Materials Characterization
- Publisher
- Elsevier BV
- Published
- 2015-04
- Volume
- 102
- Pages
- 47-61
- ISSN
- 1044-5803 (ISSN-L)
- OpenAlex
- W2043225275
- Cited by
- 590
- References
- 32
- FWCI
- 55.25
- Type
- journal article
- Language
- en
- Open access
- hybrid
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.