The DOI matches its Crossref record; 13 of the 13 references it cites were found in a registry or an index.
Self-Healing Four-Dimensional Printing with an Ultraviolet Curable Double-Network Shape Memory Polymer System
Abstract
Four-dimensional (4D) printing that enables 3D printed structures to change configurations over time has gained great attention because of its exciting potential in various applications. Among all the 4D printing materials, shape memory polymers (SMPs) possess higher stiffness and faster response rate and therefore are considered as one of most promising materials for 4D printing. However, most of the SMP-based 4D printing materials are (meth)acrylate thermosets which have permanently cross-linked covalent networks and cannot be repaired if any damage occurs. To address the unrepairable nature of SMP-based 4D printing materials, this paper reports a double-network self-healing SMP (SH-SMP) system for high-resolution self-healing 4D printing. In the SH-SMP system, the semicrystalline linear polymer polycaprolactone (PCL) is incorporated into a methacrylate-based SMP system which has good compatibility with the digital light processing-based 3D printing technology and can be used to fabricate complex 4D printing structures with high resolution (up to 30 μm). The PCL linear polymer imparts the self-healing ability to the 4D printing structures, and the mechanical properties of a damaged structure can be recovered to more than 90% after adding more than 20 wt % of PCL into the SH-SMP system. We investigated the effects of PCL concentration on the thermomechanical behavior, viscosity, and the self-healing capability of the SH-SMP system and performed the computational fluid dynamics simulations to study the effect of SH-SMP solution's viscosity on the 3D printing process. Finally, we demonstrated the self-healing 4D printing application examples to show the merits of the SH-SMP system.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Design, fabrication and control of soft robots
Rus, D., & Tolley, M. T. (2015) · Nature · doi:10.1038/nature14543 · Cited by 5,825
The return of a forgotten polymer—Polycaprolactone in the 21st century
Woodruff, M. A., & Hutmacher, D. W. (2010) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2010.04.002 · Cited by 4,033
Sydney Gladman, A., Matsumoto, E. A., Nuzzo, R. G., Mahadevan, L., & Lewis, J. A. (2016) · Nature Materials · doi:10.1038/nmat4544 · Cited by 3,027
Light-induced shape-memory polymers
Lendlein, A., Jiang, H., Jünger, O., & Langer, R. (2005) · Nature · doi:10.1038/nature03496 · Cited by 2,006
Tunable polymer multi-shape memory effect
Xie, T. (2010) · Nature · doi:10.1038/nature08863 · Cited by 1,380
Momeni, F., M.Mehdi Hassani.N, S., Liu, X., & Ni, J. (2017) · Materials & Design · doi:10.1016/j.matdes.2017.02.068 · Cited by 1,165
Multimaterial 4D Printing with Tailorable Shape Memory Polymers
Ge, Q., Sakhaei, A. H., Lee, H., Dunn, C. K., Fang, N. X., & Dunn, M. L. (2016) · Scientific Reports · doi:10.1038/srep31110 · Cited by 1,160
Self-citationActive materials by four-dimension printing
Ge, Q., Qi, H. J., & Dunn, M. L. (2013) · Applied Physics Letters · doi:10.1063/1.4819837 · Cited by 785
Self-citationDirect 4D Printing Via Active Composite Materials
Ding, Z., Yuan, C., Peng, X., Wang, T., Qi, H. J., & Dunn, M. L. (2017) · Science Advances · doi:10.1126/sciadv.1602890 · Cited by 692
Active printed materials for complex self-evolving deformations
Raviv, D., Zhao, W., McKnelly, C., Papadopoulou, A., Kadambi, A., Shi, B., Hirsch, S., Dikovsky, D., Zyracki, M., Olguin, C., et al. (2014) · Scientific Reports · doi:10.1038/srep07422 · Cited by 568
Cited by
Projection micro stereolithography based 3D printing and its applications
Ge, Q., Li, Z., Wang, Z., Kowsari, K., Zhang, W., He, X., Zhou, J., & Fang, N. X. (2020) · International Journal of Extreme Manufacturing · doi:10.1088/2631-7990/ab8d9a · Cited by 444
Self-citationExtrusion 3D Printing of Polymeric Materials with Advanced Properties
Jiang, Z., Diggle, B., Tan, M. L., Viktorova, J., Bennett, C. W., & Connal, L. A. (2020) · Advanced Science · doi:10.1002/advs.202001379 · Cited by 408
3D printing for polymer/particle-based processing: A review
Xu, W., Jambhulkar, S., Zhu, Y., Ravichandran, D., Kakarla, M., Vernon, B., Lott, D. G., Cornella, J. L., Shefi, O., Miquelard-Garnier, G., et al. (2021) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2021.109102 · Cited by 318
A review on self-healing polymers for soft robotics
Terryn, S., Langenbach, J., Roels, E., Brancart, J., Bakkali-Hassani, C., Poutrel, Q.-A., Georgopoulou, A., George Thuruthel, T., Safaei, A., Ferrentino, P., et al. (2021) · Materials Today · doi:10.1016/j.mattod.2021.01.009 · Cited by 309
Rapid digital light 3D printing enabled by a soft and deformable hydrogel separation interface
Wu, J., Guo, J., Linghu, C., Lu, Y., Song, J., Xie, T., & Zhao, Q. (2021) · Nature Communications · doi:10.1038/s41467-021-26386-6 · Cited by 109
Metadata
- Authors
- Zhang, B., Zhang, W., Zhang, Z., Zhang, Y.-F., Hingorani, H., Liu, Z., Liu, J., & Ge, Q.
- Venue
- ACS Applied Materials & Interfaces
- Publisher
- American Chemical Society (ACS)
- Published
- 2019-02-20
- Volume
- 11
- Issue
- 10
- Pages
- 10328-10336
- ISSN
- 1944-8244 (ISSN-L)
- 1944-8252
- OpenAlex
- W2916478639
- Cited by
- 190
- References
- 13
- FWCI
- 9.49
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Self-Healing Four-Dimensional Printing with an Ultraviolet Curable Double-Network Shape Memory Polymer System. https://app.cochat.ai/papers/10.1021/acsami.9b00359
- The paper
- Zhang, B., Zhang, W., Zhang, Z., Zhang, Y.-F., Hingorani, H., Liu, Z., Liu, J., & Ge, Q. (2019). Self-Healing Four-Dimensional Printing with an Ultraviolet Curable Double-Network Shape Memory Polymer System. ACS Applied Materials & Interfaces. https://doi.org/10.1021/acsami.9b00359
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.