Observation of conducting filament growth in nanoscale resistive memories
Open accessThe DOI matches its Crossref record; 36 of the 36 references it cites were found in a registry or an index; 5 of the 42 sources its claims cite were checked for support.
Abstract
Nanoscale resistive switching devices, sometimes termed memristors, have recently generated significant interest for memory, logic and neuromorphic applications. Resistive switching effects in dielectric-based devices are normally assumed to be caused by conducting filament formation across the electrodes, but the nature of the filaments and their growth dynamics remain controversial. Here we report direct transmission electron microscopy imaging, and structural and compositional analysis of the nanoscale conducting filaments. Through systematic ex-situ and in-situ transmission electron microscopy studies on devices under different programming conditions, we found that the filament growth can be dominated by cation transport in the dielectric film. Unexpectedly, two different growth modes were observed for the first time in materials with different microstructures. Regardless of the growth direction, the narrowest region of the filament was found to be near the dielectric/inert-electrode interface in these devices, suggesting that this region deserves particular attention for continued device optimization.
Overview
CoChat Summary
## TL;DR
Using ex-situ and in-situ TEM, the paper directly visualizes conducting filaments in nanoscale resistive memories and shows that filament growth can be limited by cation transport in the dielectric. It also reports two growth modes, including an unexpected mode in which filaments start from the active electrode and grow toward the inert electrode.
## Key findings
- In over 100 devices studied, none showed more than one completed filament.
- For SiO2-based devices, the authors observed conical filaments with a typical lateral size of ~20 nm near the tip and ~70 nm at the base; the filaments were verified to be composed of elemental Ag.
- In a-Si-based devices, partially formed filaments were sometimes seen starting from the active Ag electrode, and detailed TEM/EDS/SAED showed they were also composed of elemental Ag, sometimes as a chain of nanoparticles separated by 1–4 nm gaps.
- Across device types, the narrowest region of the filament was found near the dielectric/inert-electrode interface, and erasing typically began there; in-situ TEM on vertical Ag/a-Si/W devices confirmed this active-electrode-to-inert-electrode growth and inert-interface dissolution.
## Methods
- The study combined ex-situ and in-situ transmission electron microscopy with structural and compositional analysis (TEM, STEM/HAADF, HRTEM, SAED, EDS) on resistive memory devices.
- Devices used different dielectric layers of about 15 nm thickness: SiO2, Al2O3, and a-Si; planar devices were fabricated on ultrathin 15 nm SiNx membranes, and vertical Ag/a-Si/W devices were used for in-situ TEM.
- Electrical switching was measured with current compliance; the main analysis related filament morphology and switching behavior to dielectric choice, programming current, electric field, and temperature, including 36 a-Si-based resistive switches for the field-scaling data.
## Limitations
- The authors state that the switching time and electric field used here are still different from standard ECM cell operating conditions, so the filament growth under specific conditions must be analyzed individually.
- The paper itself notes that detailed analysis of the electrochemical processes and cation transport dynamics remains for future investigation.
- Evident from the text: many conclusions are based on specific device geometries and materials under ex-situ/in-situ TEM conditions, so direct generalization to all resistive memories is not established in the paper.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures





Verification
Claims the paper makes
4 Valid · 1 Not valid · 15 Not checked · 77 Own results and interpretations
Every source the paper cites for this claim was checked and supports it.
In the paper
“In general, the filament growth is determined by three dynamic processes 27 : (i) the anodic dissolution of the metal component at the active electrode; (ii) the transport of the metal ions through the dielectrics; and (iii) the reduction of metal ions and the crystallization of conducting filaments.”
What the sources say
- Supportedcites [27] Valov, I., Waser, R., Jameson, J. R & Kozicki,, M. N. Electrochemical metallization memories — fundamentals, applications, prospects. Nanotechnol. 22, 254003 (2011). source
Split into 3 atoms — 3 confirmed, 0 partially supported, 0 disputed, 0 misattributed, 0 unverifiable. Expand the claim to see per-atom verdicts.
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“This effect explains the observations in ECM devices that lower threshold voltages are typically required during programming processes, compared with those for the initial forming process 22,27,28 .”
What the sources say
- Not checked — no full text of the sourcecites [22] Waser, R., Dittmann, R., Staikov, G. & Szot, K. Redox-based resistive switching memories - Nanoionic mechanisms, prospects, and challenges. Adv. Mater. 21, 2632–2663 (2009). source
- Partly supportedcites [27] Valov, I., Waser, R., Jameson, J. R & Kozicki,, M. N. Electrochemical metallization memories — fundamentals, applications, prospects. Nanotechnol. 22, 254003 (2011). sourceExperimental — accuracy not yet measured
Section 3.3 (page unavailable) distinguishes the initial forming cycle from later switching cycles and suggests that forming may leave a nano-channel that aids subsequent filament growth. This supports the proposed mechanism, but the passage does not state that programming threshold voltages are typically lower than forming voltages. (LLM, conf=0.78)
- Not checked — no full text of the sourcecites [28] Schindler, C., Staikov, G. & Waser, R. Electrode kinetics of Cu–SiO2-based resistive switching cells: Overcoming the voltage-time dilemma of electrochemical metallization memories. Appl. Phys. Lett. 94, 072109 (2009). source
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“the filaments in Fig. 1b apparently started growth from the inert electrode side as evidenced by the locations of the partially formed filaments.”
hedgedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“many of the incomplete filaments exhibiting a noteworthy dendrite structure with the branches pointing towards the active electrode”
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“we provide unambiguous evidence that shows that localized, nanoscale filaments composed of elemental metals (and, in some cases, consisting of discrete nanoparticles instead of a solid wire) are formed during resistive switching.”
boostedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
51 more claims
Create a free account to see all 97 claims and every source verdict.
- It may state two separate claims as one. 36
- Probably not a substantial claim. 10
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“The change from OFF to ON state is explained by the formation of a dominating Ag filament (15,16).”
From Stochastic memristive devices for computing and neuromorphic applications (2013) · cites this paper as [16]
Citations
Cites
Strukov, D. B., Snider, G. S., Stewart, D. R., & Williams, R. S. (2008) · Nature · doi:10.1038/nature06932 · Cited by 11,828
Memristor—The Missing Circuit Element
Chua, L. (1971) · IEEE Transactions on Circuit Theory · doi:10.1109/tct.1971.1083337 · Cited by 10,268
Redox‐Based Resistive Switching Memories – Nanoionic Mechanisms, Prospects, and Challenges
Waser, R., Dittmann, R., Staikov, G., & Szot, K. (2009) · Advanced Materials · doi:10.1002/adma.200900375 · Cited by 5,080
Nanoionics-based resistive switching memories
Waser, R., & Aono, M. (2007) · Nature Materials · doi:10.1038/nmat2023 · Cited by 4,923
Nanoscale Memristor Device as Synapse in Neuromorphic Systems
Jo, S. H., Chang, T., Ebong, I., Bhadviya, B. B., Mazumder, P., & Lu, W. (2010) · Nano Letters · doi:10.1021/nl904092h · Cited by 4,174
Self-citationMemristive switching mechanism for metal/oxide/metal nanodevices
Yang, J. J., Pickett, M. D., Li, X., Ohlberg, D. A. A., Stewart, D. R., & Williams, R. S. (2008) · Nature Nanotechnology · doi:10.1038/nnano.2008.160 · Cited by 2,987
Memristive devices and systems
Chua, L. O., & Kang, S. M. (1976) · Proceedings of the IEEE · doi:10.1109/proc.1976.10092 · Cited by 2,604
Atomic structure of conducting nanofilaments in TiO2 resistive switching memory
Kwon, D.-H., Kim, K. M., Jang, J. H., Jeon, J. M., Lee, M. H., Kim, G. H., Li, X.-S., Park, G.-S., Lee, B., Han, S., et al. (2010) · Nature Nanotechnology · doi:10.1038/nnano.2009.456 · Cited by 2,092
‘Memristive’ switches enable ‘stateful’ logic operations via material implication
Borghetti, J., Snider, G. S., Kuekes, P. J., Yang, J. J., Stewart, D. R., & Williams, R. S. (2010) · Nature · doi:10.1038/nature08940 · Cited by 1,929
Complementary resistive switches for passive nanocrossbar memories
Linn, E., Rosezin, R., Kügeler, C., & Waser, R. (2010) · Nature Materials · doi:10.1038/nmat2748 · Cited by 1,274
Cited by
Items 501–600 of 1,201
Nguyen, V. S., Mai, V. H., Auban‐Senzier, P., Pasquier, C., Wang, K., Rozenberg, M. J., Brun, N., March, K., Jomard, F., Giapintzakis, J., et al. (2018) · Small · doi:10.1002/smll.201801038 · Cited by 27
Liu, K., Qin, L., Zhang, X., Zhu, J., Sun, X., Ke, Y., Cai, Y., Yang, Y., & Huang, R. (2018) · Faraday Discussions · doi:10.1039/c8fd00113h · Cited by 29
Self-citationAtomic Layer Deposition Films for Resistive Random‐Access Memories
Hao, C., Peng, J., Zierold, R., & Blick, R. H. (2024) · Advanced Materials Technologies · doi:10.1002/admt.202301762 · Cited by 26
Inkjet Printed Metal–Organic Frameworks for Non‐Volatile Memory Devices Suitable for Printed RRAM
Liu, Y., Fischer, F., Hu, H., Gliemann, H., Natzeck, C., Schwotzer, M., Rainer, C., Lemmer, U., Wöll, C., Breitung, B., et al. (2024) · Advanced Functional Materials · doi:10.1002/adfm.202412372 · Cited by 37
Neural vs Neuromorphic Interfaces: Where Are We Standing?
Rana, D., Babushkina, N., Gini, M., Cáceres, A., Li, H., Maybeck, V., Criscuolo, V., Mayer, D., Ienca, M., Musall, S., et al. (2025) · Chemical Reviews · doi:10.1021/acs.chemrev.4c00862 · Cited by 30
In-situ transmission electron microscopy for probing the dynamic processes in materials
Zhu, Y., Zhao, H., He, Y., & Wang, R. (2021) · Journal of Physics D Applied Physics · doi:10.1088/1361-6463/ac1a9d · Cited by 28
“Reprinted by permission from Springer Nature Customer Service Centre GmbH: NatureNatureCommunication [126] (2012).”
MethodBousoulas, P., Tsioustas, C., Hadfield, J., Aslanidis, V., Limberopoulos, S., & Tsoukalas, D. (2022) · IEEE Transactions on Electron Devices · doi:10.1109/ted.2022.3160138 · Cited by 30
Jones, J., Snowdon, M. R., Rathod, S., & Peng, P. (2023) · Flexible and Printed Electronics · doi:10.1088/2058-8585/acb0df · Cited by 29
“Cu2O has been shown in several works [35, 36] to demonstrate resistive switching behavior through the formation of a conducting filament, formed by the migration of the oxygen vacancies [37, 38] and copper defects [39, 40] under an electric bias.”
Picosecond Time‐Scale Resistive Switching Monitored in Real‐Time
Csontos, M., Horst, Y., Olalla, N. J., Koch, U., Shorubalko, I., Halbritter, A., & Leuthold, J. (2023) · Advanced Electronic Materials · doi:10.1002/aelm.202201104 · Cited by 27
Yadav, R., Poudyal, S., Rajarapu, R., Biswal, B., Barman, P. K., Kasiviswanathan, S., Novoselov, K. S., & Misra, A. (2023) · Small · doi:10.1002/smll.202309163 · Cited by 29
Single-crystalline CuO nanowires for resistive random access memory applications
Hong, Y.-S., Chen, J.-Y., Huang, C., Chiu, C., Huang, Y.-T., Huang, T. K., He, R. S., & Wu, W. (2015) · Applied Physics Letters · doi:10.1063/1.4919102 · Cited by 25
Analysis of the Negative-SET Behaviors in Cu/ZrO2/Pt Devices
Liu, S., Zhao, X., Li, Q., Li, N., Wang, W., Liu, Q., & Xu, H. (2016) · Nanoscale Research Letters · doi:10.1186/s11671-016-1762-5 · Cited by 27
Sun, Y., & Wen, D. (2018) · The Journal of Physical Chemistry C · doi:10.1021/acs.jpcc.8b01120 · Cited by 26
Universal 1/ f type current noise of Ag filaments in redox-based memristive nanojunctions
Sánta, B., Balogh, Z., Gubicza, Á., Pósa, L., Krisztián, D., Mihály, G., Csontos, M., & Halbritter, A. (2019) · Nanoscale · doi:10.1039/c8nr09985e · Cited by 27
Qin, L., Guan, P., Shao, J., Xiao, Y., Yu, Y., Su, J., Zhang, C., Li, Y., Liu, S., Li, P., et al. (2025) · Nature Nanotechnology · doi:10.1038/s41565-025-02013-z · Cited by 42
Electrically and Optically Readable Light Emitting Memories
Chang, C., Tan, W.-C., Lu, M., Pan, T.-C., Yang, Y. J., & Chen, Y. (2014) · Scientific Reports · doi:10.1038/srep05121 · Cited by 25
Self-citationOnofrio, N., Guzman, D., & Strachan, A. H. (2016) · Nanoscale · doi:10.1039/c6nr01335j · Cited by 25
Dananjaya, P. A., Loy, D. J., Chow, S. C. W., & Lew, W. S. (2019) · ACS Applied Electronic Materials · doi:10.1021/acsaelm.9b00446 · Cited by 27
Purushothama, J. M., López-Soriano, S., Vena, A., et al. (2020) · IEEE Transactions on Antennas and Propagation · doi:10.1109/tap.2020.3030965 · Cited by 25
“Suitable materials for ion conductor application include oxidizable metal doped chalcogenide glass [17], [21], ion conducting and metal doped polymers [25]–[27], semiconductor oxides [23], [28], and even nanometrically spaced air gaps [22].”
BackgroundTemporal Pattern Coding in Ionic Memristor‐Based Spiking Neurons for Adaptive Tactile Perception
Xie, Z., Zhu, X., Wang, W., Guo, Z., Zhang, Y., Liu, H., Sun, C., Tang, M., Gao, S., & Li, R. (2022) · Advanced Electronic Materials · doi:10.1002/aelm.202200334 · Cited by 26
Zhang, K., Ganesh, P., & Cao, Y. (2023) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.3c00371 · Cited by 26
Fan, J., Feng, J., Gao, Y., et al. (2024) · ACS Applied Nano Materials · doi:10.1021/acsanm.4c00759 · Cited by 25
Theoretical investigation of the Ag filament morphology in conductive bridge random access memories
Xue, K., Li, Y., Su, H.-L., Yuan, J., Li, Y., Wang, Z., Zhang, B., & Miao, X. (2018) · Journal of Applied Physics · doi:10.1063/1.5042165 · Cited by 26
Tunnel conductivity switching in a single nanoparticle-based nano floating gate memory
Gambardella, A., Prezioso, M., & Cavallini, M. (2014) · Scientific Reports · doi:10.1038/srep04196 · Cited by 24
Zhang, L., Xu, H., Wang, Z., Yu, H., Ma, J., & Liu, Y. (2015) · Applied Surface Science · doi:10.1016/j.apsusc.2015.11.022 · Cited by 23
Understanding the conduction and switching mechanism of Ti/AlOx/TaOx/Pt analog memristor
Liu, S., Sun, Y., Song, B., Li, Z., Liu, H., & Li, Q. (2019) · Physics Letters A · doi:10.1016/j.physleta.2019.125877 · Cited by 24
Intrinsic memristive mechanisms in 2D layered materials for high-performance memory
Li, H., Tao, L., & Xu, J. (2021) · Journal of Applied Physics · doi:10.1063/5.0035764 · Cited by 24
Zhou, P., Lin, X., Chee, M. Y., et al. (2023) · Materials Horizons · doi:10.1039/d3mh00037k · Cited by 24
Ultra-Low Power Ni/HfO2/TiOx/TiN Resistive Random Access Memory With Sub-30-nA Reset Current
Zhang, K., Sun, K., Wang, F., Han, Y., Jiang, Z., Zhao, J., Wang, B., Zhang, H., Jian, X., & Wong, H. ‐. P. (2015) · IEEE Electron Device Letters · doi:10.1109/led.2015.2464239 · Cited by 24
“DUE to its simple structure, fast speed (<10 ns) and high density (∼4F2) [1]–[3], metal oxide based resistive random access memory (RRAM) is one of the most promising next-generation non-volatile memories [4]–[6].”
BackgroundFujii, T., 有田正志, Hamada, K., Takahashi, Y., & Sakaguchi, N. (2013) · Journal of Applied Physics · doi:10.1063/1.4792732 · Cited by 25
Shao, X. L., Kim, K. M., Yoon, K. J., Song, S. J., Yoon, J. H., Kim, H. J., Park, T. H., Kwon, D. E., Kwon, Y. J., Kim, Y. M., et al. (2016) · Nanoscale · doi:10.1039/c6nr02800d · Cited by 27
Tsurumaki‐Fukuchi, A., Nakagawa, R., 有田正志, & Takahashi, Y. (2018) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.7b15384 · Cited by 24
Nanofilament Dynamics in Resistance Memory: Model and Validation
Lu, Y., Lee, J.-H., & Chen, I. (2015) · ACS Nano · doi:10.1021/acsnano.5b03032 · Cited by 24
Voltage-polarity dependent multi-mode resistive switching on sputtered MgO nanostructures
Dias, C., Guerra, L., Bordalo, B. D., et al. (2017) · Physical Chemistry Chemical Physics · doi:10.1039/c7cp00062f · Cited by 24
Dong, W., Ji, X., An, C., Xu, C., Zhang, X., Zhao, B., Liu, Y., Wang, S., Yu, X., Liu, X.-J., et al. (2025) · InfoMat · doi:10.1002/inf2.12659 · Cited by 28
Interconversion Between Bipolar and Complementary Behavior in Nanoscale Resistive Switching Devices
He, Y., Ma, G., Cai, H., Liu, C., Chen, A., Chen, Q., Wang, H., & Chang, T. (2018) · IEEE Transactions on Electron Devices · doi:10.1109/ted.2018.2882652 · Cited by 23
Self-citationRoy, A., & Cha, P. (2020) · Journal of Applied Physics · doi:10.1063/5.0026350 · Cited by 23
Low-Dimensional-Materials-Based Flexible Artificial Synapse: Materials, Devices, and Systems
Lu, Q., Zhao, Y., Huang, L., An, J., Zheng, Y., & Yap, E. H. (2023) · Nanomaterials · doi:10.3390/nano13030373 · Cited by 27
Tian, Q., Chen, X., Zhao, X., Wang, Z., Lin, Y., Tao, Y., Xu, H., & Liu, Y. (2023) · Applied Physics Letters · doi:10.1063/5.0142742 · Cited by 24
Lee, D., Chae, M., Jung, J.-S., et al. (2023) · ACS Sensors · doi:10.1021/acssensors.3c00541 · Cited by 23
Panja, R., Roy, S., Jana, D., & Maikap, S. (2014) · Nanoscale Research Letters · doi:10.1186/1556-276x-9-692 · Cited by 23
Switching Dynamics and Conductance Quantization of $Aloe$ Polysaccharides-Based Device
Lim, Z. X., Tayeb, I. A., Hamid, Z. A. A., Ain, M. F., Hashim, A., Abdullah, J. M., Zhao, F., & Cheong, K. Y. (2019) · IEEE Transactions on Electron Devices · doi:10.1109/ted.2019.2915106 · Cited by 25
“, once a dominant filament is established, further growth of other filaments are suppressed owing to the reduced electric fields) [8], these analytical models were proposed based on the assumption that resistive switching is due to the formation of a single dominant filament in the device.”
BackgroundAlcohol‐Mediated Resistance‐Switching Behavior in Metal–Organic Framework‐Based Electronic Devices
Liu, Y., Wang, H., Shi, W., Zhang, W., Yu, J., Chandran, B. K., Cui, C., Zhu, B., Liu, Z., Li, B., et al. (2016) · Angewandte Chemie · doi:10.1002/ange.201602499 · Cited by 23
Gubicza, Á., Csontos, M., Halbritter, A., & Mihály, G. (2015) · Nanoscale · doi:10.1039/c5nr02536b · Cited by 26
Proton-electron coupling and mixed conductivity in a hydrogen-bonded coordination polymer
Park, M., Ju, H., Oh, J., Park, K. C., Lim, H., Yoon, S. M., & Song, I. (2025) · Nature Communications · doi:10.1038/s41467-025-56541-2 · Cited by 24
Zhang, H., Ang, D. S., Yew, K. S., & Wang, X. P. (2016) · Applied Physics Letters · doi:10.1063/1.4942801 · Cited by 22
Dynamic structure-properties characterization and manipulation in advanced nanodevices
Xu, H., Wu, X., Tian, X., Li, J., Chu, J., & Sun, L. (2019) · Materials Today Nano · doi:10.1016/j.mtnano.2019.100042 · Cited by 22
Sahu, D. P., Park, K., Han, J., & Yoon, T. (2022) · APL Materials · doi:10.1063/5.0090425 · Cited by 22
Sikdar, S., Sahu, B. P., & Dhar, S. (2023) · Applied Physics Letters · doi:10.1063/5.0125821 · Cited by 20
Anisotropic mass transport enables distinct synaptic behaviors on 2D material surface
Yang, Z., Yang, Z., Liu, L., Li, X., Li, J., Xiong, C., Mai, X., Tong, H., Li, Y., Xue, K., et al. (2023) · Materials Today Electronics · doi:10.1016/j.mtelec.2023.100047 · Cited by 22
Recent Advances in Cerium Oxide-Based Memristors for Neuromorphic Computing
Ali, S., Ullah, M. A., Raza, A., Iqbal, M. W., Khan, M. F., Rasheed, M., Ismail, M., & Kim, S. (2023) · Nanomaterials · doi:10.3390/nano13172443 · Cited by 22
Resistive switching localization by selective focused ion beam irradiation
Ghazikhanian, N., del Valle, J., Salev, P., Hage, R. E., Kalcheim, Y., Adda, C., & Schuller, I. K. (2023) · Applied Physics Letters · doi:10.1063/5.0151823 · Cited by 25
Wang, G., Sun, F., Zhou, S., Zhang, Y., Zhang, F., Wang, H., Huang, J., & Zheng, Y. (2024) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.3c18146 · Cited by 25
Yin, J., Zeng, F., Wan, Q., Sun, Y., Hu, Y., Liu, J., Li, G., & Pan, F. (2018) · The Journal of Physical Chemistry C · doi:10.1021/acs.jpcc.8b09793 · Cited by 21
Resistive switching behavior of organic-metallic halide perovskites CH3NH3Pb1−Bi Br3
Ruan, W., Hu, Y., Xu, F. Y., & Zhang, S. (2019) · Organic Electronics · doi:10.1016/j.orgel.2019.04.031 · Cited by 21
Sleep-Dependent Memory Consolidation in a Neuromorphic Nanowire Network
Li, Q., Álvarez, A. D., Tang, D., Higuchi, R., Shingaya, Y., & Nakayama, T. (2020) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.0c11157 · Cited by 25
Quantum-Dots Optimized Electrode for High-Stability Transient Memristor
Chang, K., Yu, X., Liu, B., Niu, Y., REN-ZHI, W., Bao, P., Hu, G., & Wang, H. (2021) · IEEE Electron Device Letters · doi:10.1109/led.2021.3075835 · Cited by 22
“We believed that controlling the movement of metal inclusions is an effective method to decrease the random nature of RS behavior and improve device performance [16], [17].”
BackgroundMethodCruces, S., Ganeriwala, M. D., Lee, J., Ran, K., Jo, J., Völkel, L., Braun, D., Canto, B., Marín, E. G., Kalisch, H., et al. (2025) · Nano Letters · doi:10.1021/acs.nanolett.5c01992 · Cited by 24
A solution processed metal–oxo cluster for rewritable resistive memory devices
Zhou, K., Ding, G., Zhang, C., et al. (2018) · Journal of Materials Chemistry C · doi:10.1039/c8tc05188g · Cited by 21
Artificial Astrocyte Memristor with Recoverable Linearity for Neuromorphic Computing
Cheng, C., Wang, Y., Xu, L., Liu, K., Dang, B., Lu, Y., Yan, X., Huang, R., & Yang, Y. (2021) · Advanced Electronic Materials · doi:10.1002/aelm.202100669 · Cited by 21
Self-citationGold Nanoparticle in Chemoelectronics: Fundamentals, Challenges, and Future Prospects
Wang, J., Liu, L., Guo, J., Zhao, X., Zhang, Y., & Yan, Y. L. (2023) · Advanced Functional Materials · doi:10.1002/adfm.202309531 · Cited by 23
Cheung, S. S., Tossoun, B. M., Yuan, Y., Peng, Y., Hu, Y., Sorin, W. V., Kurczveil, G., Liang, D., & Beausoleil, R. G. (2024) · Communications Engineering · doi:10.1038/s44172-024-00197-1 · Cited by 30
Kalaev, D., Yalon, E., & Riess, I. (2015) · Solid State Ionics · doi:10.1016/j.ssi.2015.03.017 · Cited by 21
An overview of the switching parameter variation of RRAM
Zhang, M., Long, S., Wang, G., Li, Y., Xu, X., Liu, H., Liu, R., Wang, M., Li, C., Sun, P., et al. (2014) · Chinese Science Bulletin · doi:10.1007/s11434-014-0673-z · Cited by 22
“Low variability and high reliability are key aspects for successful applications, but to acquire them we need to thoroughly understand the physics [29–39] and statistics of switching [26–28, 40–45].”
BackgroundZhuge, F., Li, J., Chen, H., Wang, J., Zhu, L. Q., Bian, B., Fu, B., Wang, Q. L., Li, L., Pan, R., et al. (2015) · Applied Physics Letters · doi:10.1063/1.4913588 · Cited by 21
Nayak, A., Wang, Q., Itoh, Y., Tsuruoka, T., Hasegawa, T., Boodhoo, L., Mizuta, H., & Aono, M. (2015) · Nanotechnology · doi:10.1088/0957-4484/26/14/145702 · Cited by 22
“The Cu/Ta2O5/Pt devices were fabricated on SiO2/Si substrates.”
BackgroundZhao, D., Qiao, S., Luo, Y., Chen, A., Zhang, P., Zheng, P., Sun, Z., Guo, M., Chiang, F., Wu, J. C., et al. (2017) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.6b16458 · Cited by 21
Qian, K., Han, X., Li, H., Chen, T. P., & Lee, P. S. (2019) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.9b16325 · Cited by 21
Self-formed conductive nanofilaments in (Bi, Mn)O for ultralow-power memory devices
Kang, C., Kuo, W.-C., Bao, W., Ho, C.-H., Huang, C., Wu, W., Chu, Y., Juang, J., Tseng, S. H., Hu, L., et al. (2015) · Nano Energy · doi:10.1016/j.nanoen.2015.02.033 · Cited by 20
Resistive Switching‐based Electro‐Optical Modulation
Battal, E., Ozcan, A., & Okyay, A. K. (2014) · Advanced Optical Materials · doi:10.1002/adom.201400209 · Cited by 23
A Braitenberg Vehicle Based on Memristive Neuromorphic Circuits
Wang, C., Yang, Z.-Z., Wang, S., Wang, P., Wang, C., Pan, C., Cheng, B., Liang, S., & Miao, F. (2019) · Advanced Intelligent Systems · doi:10.1002/aisy.201900103 · Cited by 23
A Study of the Memristor Models and Applications
Keshmiri, V. (2014) · DiVA (Digitala Vetenskapliga Arkivet) · Cited by 37
Yu, T., Zhao, Z., Jiang, H., Weng, Z., Fang, Y., Yu, Y., Lei, W., Shafe, S. B., & Mohtar, M. N. (2022) · Materials Today Chemistry · doi:10.1016/j.mtchem.2022.101268 · Cited by 22
Rehman, N. U., Khan, R., Rahman, N., Ahmad, I., Ullah, A., Sohail, M., Iqbal, S., Althubeiti, K., Otaibi, S. A., Juraev, N., et al. (2024) · Journal of Materials Science Materials in Electronics · doi:10.1007/s10854-024-13318-5 · Cited by 22
“The resistive switching device with Ag electrode usually reported that the switching behavior is due to the formation and the rupture of Ag bridge between the TE and BE under the voltage bias [37, 46].”
Korneluk, A., & Stefaniuk, T. (2024) · Advanced Materials · doi:10.1002/adma.202411186 · Cited by 22
Xiao, X.-Y., Peng, Z., Zhang, Z., et al. (2024) · Nature Communications · doi:10.1038/s41467-024-54900-z · Cited by 20
“However, the conventional conductive fi lament formation mechanism, which has been observed also in metal oxide memristors 25 , might not work aswell in printed layersof nanosheets: it is well known that single layer 2D materials are dif fi cult for ions to penetrate due to the high energy barrier…”
Cherukara, M. J., Sasikumar, K., DiChiara, A. D., et al. (2017) · Nano Letters · doi:10.1021/acs.nanolett.7b03823 · Cited by 20
Resistive Switching Memristor: On the Direct Observation of Physical Nature of Parameter Variability
Wang, Z., Xiao, W., Yang, H., Zhang, S., Zhang, Y., Sun, K., Wang, T., Fu, Y., Wang, Q., Zhang, J., et al. (2021) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.1c19364 · Cited by 21
Li, J., Yao, C., Ke, Y., Huang, W., Thatikonda, S. K., Qin, N., & Bao, D. (2022) · Applied Physics Letters · doi:10.1063/5.0086415 · Cited by 22
A Bifunctional Memristor Enables Multiple Neuromorphic Computing Applications
Lyapunov, N., Zheng, X. D., Yang, K., Liu, H. M., Zhou, K., Cai, S., Ho, T. L., Suen, C. H., Yang, M., Zhao, J. X., et al. (2022) · Advanced Electronic Materials · doi:10.1002/aelm.202101235 · Cited by 20
Tyrosine-mediated analog resistive switching for artificial neural networks
Song, M., Namgung, S. D., Lee, H., Yoon, J. H., Song, Y., Cho, K. H., Lee, Y., Lee, J., Nam, K. T., & Kwon, J. (2022) · Nano Research · doi:10.1007/s12274-022-4760-1 · Cited by 21
Genesis of Nanogalvanic Corrosion Revealed in Pearlitic Steel
Hayden, S. C., Chisholm, C., Eichmann, S. L., et al. (2022) · Nano Letters · doi:10.1021/acs.nanolett.2c02122 · Cited by 20
Dual-conductivity mechanism investigation of 2D α-MoO3-based multi-level memristor
Shan, X., liu, P. L., Wang, F., Xie, Y., Wei, J., Ma, Z., Shi, Y., Sun, H., Lu, S., Song, Z., et al. (2023) · Science China Materials · doi:10.1007/s40843-023-2653-x · Cited by 18
“This is consistent with the results of previous analyses of the conducting mechanism [31,32].”
ResultLiu, Y., Gao, P., Jiang, X. L., Bi, K., Xu, H., & Peng, W. B. (2014) · Applied Physics Letters · doi:10.1063/1.4863509 · Cited by 19
Self-citationResistive switching characteristics of Ag/MnO/CeO 2 /Pt heterostructures memory devices
Hu, Q., Kang, T. S., Abbas, H., et al. (2017) · Microelectronic Engineering · doi:10.1016/j.mee.2017.12.014 · Cited by 20
Write-Once-Read-Many-Times Characteristic of InZnO Oxide Semiconductor
Hsu, C.-C., Tsao, C.-C., & Lin, Y.-S. (2018) · IEEE Transactions on Electron Devices · doi:10.1109/ted.2018.2798710 · Cited by 20
“These Ag cations can drift from the Ag electrode into the active layer to form conductive filaments when a positive bias is applied to the Ag electrode [21].”
Cheng, C., Li, Y., Zhang, T., Fang, Y., Zhu, J., Liu, K., Xu, L., Cai, Y., Yan, X., Yang, Y., et al. (2018) · Journal of Applied Physics · doi:10.1063/1.5037962 · Cited by 20
Self-citationXu, H., Xia, Y., Yin, K., Lu, J., Yin, Q., Yin, J., Sun, L., & Liu, Z. G. (2013) · Scientific Reports · doi:10.1038/srep01230 · Cited by 20
Switching of Cu/MoOx/TiN CBRAM at MoOx/TiN interface
有田正志, Ohno, Y., & Takahashi, Y. (2015) · physica status solidi (a) · doi:10.1002/pssa.201532414 · Cited by 19
High performance bi-layer atomic switching devices
Ju, J. H., Jang, S. K., Son, H., et al. (2017) · Nanoscale · doi:10.1039/c7nr01035d · Cited by 19
Yau, H.-M., Xi, Z., Chen, X., et al. (2017) · Physical review. B./Physical review. B · doi:10.1103/physrevb.95.214304 · Cited by 19
Krishnan, K., Tauquir, S. M., Vijayaraghavan, S., & Mohan, R. (2021) · RSC Advances · doi:10.1039/d1ra03561d · Cited by 19
Kwon, S., Kim, M., Lim, D., Jeong, K., & Chung, K. (2022) · Scientific Reports · doi:10.1038/s41598-022-12476-y · Cited by 21
Park, K., Ryu, J., Sahu, D. P., Kim, H.-M., & Yoon, T. (2022) · RSC Advances · doi:10.1039/d2ra02930h · Cited by 20
Zhang, D. “., Wang, J., Wu, Q., & Du, Y. (2022) · Physical Chemistry Chemical Physics · doi:10.1039/d2cp05803k · Cited by 19
Guo, J., Liu, L., Bian, B., Wang, J., Zhao, X., Zhang, Y., & Yan, Y. L. (2023) · Advanced Functional Materials · doi:10.1002/adfm.202212666 · Cited by 20
Huang, H., Dai, G., Wu, X.-H., Wu, Y., Wei, A., & Liu, Z. (2024) · Materials Science in Semiconductor Processing · doi:10.1016/j.mssp.2023.108073 · Cited by 17
Chauhan, M. S., Choudhary, S. K., & Sharma, S. K. (2024) · Advanced Electronic Materials · doi:10.1002/aelm.202300724 · Cited by 20
Inherently stochastic spiking neurons for probabilistic neural computation
Al-Shedivat, M., Naous, R., Neftci, E., Cauwenberghs, G., & Salama, K. N. (2015) · International IEEE/EMBS Conference on Neural Engineering · doi:10.1109/ner.2015.7146633 · Cited by 19
“Moreover, recently discovered nondeterministic behavior of the memristive switching [13], [16], [17] based on stochasticity of nano-filament formation in thin metal-oxide films [18] seems promising in the context of neuromorphic applications: Abrupt switching of the resistance in such devices can be used for generatin…”
BackgroundKim, S. J., Kim, H.-D., Kim, K. H., Shin, H. W., Han, I. K., & Kim, T. G. (2014) · Scientific Reports · doi:10.1038/srep05827 · Cited by 20
Metadata
- Authors
- Yang, Y., Gao, P., Gaba, S., Chang, T., Pan, X., & Lu, W.
- Affiliations
- University of Michigan (US)
- Corresponding author
- Lu, Wei
- Venue
- Nature Communications
- Published
- 2012-03-13
- Volume
- 3
- Issue
- 1
- Pages
- 732-732
- ISSN
- 2041-1723 (ISSN-L)
- OpenAlex
- W2043707274
- Cited by
- 1,208
- References
- 32
- Citations by year
- 2026: 68 · 2025: 69 · 2024: 92 · 2023: 84 · 2022: 95 · 2021: 85 · 2020: 101 · 2019: 100 · 2018: 89 · 2017: 95 · 2016: 88 · 2015: 81 · 2014: 71 · 2013: 68 · 2012: 21
- FWCI
- 49.24
- Type
- journal article
- Language
- en
- Open access
- bronze
- doi.org
- Licence
- www.springernature.com/gp/researchers/text-and-data-mining (tdm)
- www.springernature.com/gp/researchers/text-and-data-mining (vor)
- Locations
- Nature Communications (publishedVersion)
- PubMed (publishedVersion)
- RePEc: Research Papers in Economics (submittedVersion)
- Funders
- National Science Foundation (0723032, 0907191, 0954621)
- Defense Advanced Research Projects Agency (HRL0011-09-C-001)
- Division of Materials Research (0723032, DMR-0723032)
- Division of Electrical, Communications and Cyber Systems (ECCS-0954621)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Advanced Memory and Neural Computing
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Ferroelectric and Negative Capacitance Devices
- Physical Sciences › Materials Science › Materials Chemistry › Phase-change materials and chalcogenides
- Keywords
- resistive switching, memristors, electrochemical metallization, cation transport, dielectric films, non-volatile memory, in situ transmission electron microscopy
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-09-30, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-09-30 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.