Observation of conducting filament growth in nanoscale resistive memories
Open accessThe DOI matches its Crossref record; 36 of the 36 references it cites were found in a registry or an index; 5 of the 42 sources its claims cite were checked for support.
Abstract
Nanoscale resistive switching devices, sometimes termed memristors, have recently generated significant interest for memory, logic and neuromorphic applications. Resistive switching effects in dielectric-based devices are normally assumed to be caused by conducting filament formation across the electrodes, but the nature of the filaments and their growth dynamics remain controversial. Here we report direct transmission electron microscopy imaging, and structural and compositional analysis of the nanoscale conducting filaments. Through systematic ex-situ and in-situ transmission electron microscopy studies on devices under different programming conditions, we found that the filament growth can be dominated by cation transport in the dielectric film. Unexpectedly, two different growth modes were observed for the first time in materials with different microstructures. Regardless of the growth direction, the narrowest region of the filament was found to be near the dielectric/inert-electrode interface in these devices, suggesting that this region deserves particular attention for continued device optimization.
Overview
CoChat Summary
## TL;DR
Using ex-situ and in-situ TEM, the paper directly visualizes conducting filaments in nanoscale resistive memories and shows that filament growth can be limited by cation transport in the dielectric. It also reports two growth modes, including an unexpected mode in which filaments start from the active electrode and grow toward the inert electrode.
## Key findings
- In over 100 devices studied, none showed more than one completed filament.
- For SiO2-based devices, the authors observed conical filaments with a typical lateral size of ~20 nm near the tip and ~70 nm at the base; the filaments were verified to be composed of elemental Ag.
- In a-Si-based devices, partially formed filaments were sometimes seen starting from the active Ag electrode, and detailed TEM/EDS/SAED showed they were also composed of elemental Ag, sometimes as a chain of nanoparticles separated by 1–4 nm gaps.
- Across device types, the narrowest region of the filament was found near the dielectric/inert-electrode interface, and erasing typically began there; in-situ TEM on vertical Ag/a-Si/W devices confirmed this active-electrode-to-inert-electrode growth and inert-interface dissolution.
## Methods
- The study combined ex-situ and in-situ transmission electron microscopy with structural and compositional analysis (TEM, STEM/HAADF, HRTEM, SAED, EDS) on resistive memory devices.
- Devices used different dielectric layers of about 15 nm thickness: SiO2, Al2O3, and a-Si; planar devices were fabricated on ultrathin 15 nm SiNx membranes, and vertical Ag/a-Si/W devices were used for in-situ TEM.
- Electrical switching was measured with current compliance; the main analysis related filament morphology and switching behavior to dielectric choice, programming current, electric field, and temperature, including 36 a-Si-based resistive switches for the field-scaling data.
## Limitations
- The authors state that the switching time and electric field used here are still different from standard ECM cell operating conditions, so the filament growth under specific conditions must be analyzed individually.
- The paper itself notes that detailed analysis of the electrochemical processes and cation transport dynamics remains for future investigation.
- Evident from the text: many conclusions are based on specific device geometries and materials under ex-situ/in-situ TEM conditions, so direct generalization to all resistive memories is not established in the paper.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures





Verification
Claims the paper makes
4 Valid · 1 Not valid · 15 Not checked · 77 Own results and interpretations
Every source the paper cites for this claim was checked and supports it.
In the paper
“In general, the filament growth is determined by three dynamic processes 27 : (i) the anodic dissolution of the metal component at the active electrode; (ii) the transport of the metal ions through the dielectrics; and (iii) the reduction of metal ions and the crystallization of conducting filaments.”
What the sources say
- Supportedcites [27] Valov, I., Waser, R., Jameson, J. R & Kozicki,, M. N. Electrochemical metallization memories — fundamentals, applications, prospects. Nanotechnol. 22, 254003 (2011). source
Split into 3 atoms — 3 confirmed, 0 partially supported, 0 disputed, 0 misattributed, 0 unverifiable. Expand the claim to see per-atom verdicts.
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“This effect explains the observations in ECM devices that lower threshold voltages are typically required during programming processes, compared with those for the initial forming process 22,27,28 .”
What the sources say
- Not checked — no full text of the sourcecites [22] Waser, R., Dittmann, R., Staikov, G. & Szot, K. Redox-based resistive switching memories - Nanoionic mechanisms, prospects, and challenges. Adv. Mater. 21, 2632–2663 (2009). source
- Partly supportedcites [27] Valov, I., Waser, R., Jameson, J. R & Kozicki,, M. N. Electrochemical metallization memories — fundamentals, applications, prospects. Nanotechnol. 22, 254003 (2011). sourceExperimental — accuracy not yet measured
Section 3.3 (page unavailable) distinguishes the initial forming cycle from later switching cycles and suggests that forming may leave a nano-channel that aids subsequent filament growth. This supports the proposed mechanism, but the passage does not state that programming threshold voltages are typically lower than forming voltages. (LLM, conf=0.78)
- Not checked — no full text of the sourcecites [28] Schindler, C., Staikov, G. & Waser, R. Electrode kinetics of Cu–SiO2-based resistive switching cells: Overcoming the voltage-time dilemma of electrochemical metallization memories. Appl. Phys. Lett. 94, 072109 (2009). source
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“the filaments in Fig. 1b apparently started growth from the inert electrode side as evidenced by the locations of the partially formed filaments.”
hedgedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“many of the incomplete filaments exhibiting a noteworthy dendrite structure with the branches pointing towards the active electrode”
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“we provide unambiguous evidence that shows that localized, nanoscale filaments composed of elemental metals (and, in some cases, consisting of discrete nanoparticles instead of a solid wire) are formed during resistive switching.”
boostedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
51 more claims
Create a free account to see all 97 claims and every source verdict.
- It may state two separate claims as one. 36
- Probably not a substantial claim. 10
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“The change from OFF to ON state is explained by the formation of a dominating Ag filament (15,16).”
From Stochastic memristive devices for computing and neuromorphic applications (2013) · cites this paper as [16]
Citations
Cites
Strukov, D. B., Snider, G. S., Stewart, D. R., & Williams, R. S. (2008) · Nature · doi:10.1038/nature06932 · Cited by 11,828
Memristor—The Missing Circuit Element
Chua, L. (1971) · IEEE Transactions on Circuit Theory · doi:10.1109/tct.1971.1083337 · Cited by 10,268
Redox‐Based Resistive Switching Memories – Nanoionic Mechanisms, Prospects, and Challenges
Waser, R., Dittmann, R., Staikov, G., & Szot, K. (2009) · Advanced Materials · doi:10.1002/adma.200900375 · Cited by 5,080
Nanoionics-based resistive switching memories
Waser, R., & Aono, M. (2007) · Nature Materials · doi:10.1038/nmat2023 · Cited by 4,923
Nanoscale Memristor Device as Synapse in Neuromorphic Systems
Jo, S. H., Chang, T., Ebong, I., Bhadviya, B. B., Mazumder, P., & Lu, W. (2010) · Nano Letters · doi:10.1021/nl904092h · Cited by 4,174
Self-citationMemristive switching mechanism for metal/oxide/metal nanodevices
Yang, J. J., Pickett, M. D., Li, X., Ohlberg, D. A. A., Stewart, D. R., & Williams, R. S. (2008) · Nature Nanotechnology · doi:10.1038/nnano.2008.160 · Cited by 2,987
Memristive devices and systems
Chua, L. O., & Kang, S. M. (1976) · Proceedings of the IEEE · doi:10.1109/proc.1976.10092 · Cited by 2,604
Atomic structure of conducting nanofilaments in TiO2 resistive switching memory
Kwon, D.-H., Kim, K. M., Jang, J. H., Jeon, J. M., Lee, M. H., Kim, G. H., Li, X.-S., Park, G.-S., Lee, B., Han, S., et al. (2010) · Nature Nanotechnology · doi:10.1038/nnano.2009.456 · Cited by 2,092
‘Memristive’ switches enable ‘stateful’ logic operations via material implication
Borghetti, J., Snider, G. S., Kuekes, P. J., Yang, J. J., Stewart, D. R., & Williams, R. S. (2010) · Nature · doi:10.1038/nature08940 · Cited by 1,929
Complementary resistive switches for passive nanocrossbar memories
Linn, E., Rosezin, R., Kügeler, C., & Waser, R. (2010) · Nature Materials · doi:10.1038/nmat2748 · Cited by 1,274
Cited by
Items 101–200 of 1,201
Sun, Y., Tai, M., Song, C., Wang, Z., Yin, J., Li, F., Wu, H., Zeng, F., Lin, H., & Pan, F. (2018) · The Journal of Physical Chemistry C · doi:10.1021/acs.jpcc.7b12817 · Cited by 164
Nanoscale Plasmonic Memristor with Optical Readout Functionality
Emboras, A., Goykhman, I., Desiatov, B., Mazurski, N., Stern, L., Shappir, J., & Levy, U. (2013) · Nano Letters · doi:10.1021/nl403486x · Cited by 162
Liang, L., Li, K., Xiao, C., Fan, S., Liu, J., Zhang, W., Xu, W., Tong, W., Liao, J., Zhou, Y., et al. (2015) · Journal of the American Chemical Society · doi:10.1021/jacs.5b00021 · Cited by 158
Metal‐Organic Framework Nanofilm for Mechanically Flexible Information Storage Applications
Pan, L., Ji, Z., Yi, X., Zhu, X., Chen, X., Shang, J., Liu, G., & Li, R. (2015) · Advanced Functional Materials · doi:10.1002/adfm.201500449 · Cited by 159
Voltage and Power-Controlled Regimes in the Progressive Unipolar RESET Transition of HfO2-Based RRAM
Long, S., Perniola, L., Cagli, C., Buckley, J., Lian, X., Miranda, E. A., Pan, F., Liu, M., & Suñé, J. (2013) · Scientific Reports · doi:10.1038/srep02929 · Cited by 169
Lead-free monocrystalline perovskite resistive switching device for temporal information processing
Mao, J.-Y., Zheng, Z., Xiong, Z.-Y., Huang, P., Ding, G.-L., Wang, R., Wang, Z.-P., Yang, J.-Q., Zhou, Y., Zhai, T., et al. (2020) · Nano Energy · doi:10.1016/j.nanoen.2020.104616 · Cited by 158
Memristive Physically Evolving Networks Enabling the Emulation of Heterosynaptic Plasticity
Yang, Y., Chen, B., & Lu, W. D. (2015) · Advanced Materials · doi:10.1002/adma.201503202 · Cited by 158
Self-citationEmboras, A., Niegemann, J., Ma, P., Haffner, C., Pedersen, A., Luisier, M., Haffner, C., Schimmel, T., & Leuthold, J. (2015) · Nano Letters · doi:10.1021/acs.nanolett.5b04537 · Cited by 161
Metal oxide-resistive memory using graphene-edge electrodes
Lee, S., Sohn, J., Jiang, Z., Chen, H.-Y., & Wong, H. ‐. P. (2015) · Nature Communications · doi:10.1038/ncomms9407 · Cited by 156
Stochastic learning in oxide binary synaptic device for neuromorphic computing
Yu, S., Gao, B., Fang, Z., Yu, H., Kang, J., & Wong, H.-S. P. (2013) · Frontiers in Neuroscience · doi:10.3389/fnins.2013.00186 · Cited by 152
“…Ag/a-Si (Jo et al., 2010), Ag/Ag 2 S (Ohno et al., 2011) based conductive bridge memory, and TiO x (Xia et al., 2009; Seo et al., 2011), WO x (Chang et al., 2011; Yang et al., 2012a), HfO x (Yu et al., 2011a) based oxide resistive switching memory have been reported showing synaptic behaviors.”
BackgroundLv, H., Xu, X., Liu, H., Liu, R., Liu, Q., Banerjee, W., Sun, H., Long, S., Li, L., & Liu, M. (2015) · Scientific Reports · doi:10.1038/srep07764 · Cited by 164
Lübben, M., Karakolis, P., Ioannou-Sougleridis, V., Normand, P., Dimitrakis, P., & Valov, I. (2015) · Advanced Materials · doi:10.1002/adma.201502574 · Cited by 152
Xu, J., Zhao, X., Wang, Z., Xu, H., Hu, J., Ma, J., & Liu, Y. (2018) · Small · doi:10.1002/smll.201803970 · Cited by 154
Recent Developments and Perspectives for Memristive Devices Based on Metal Oxide Nanowires
Milano, G., Porro, S., Valov, I., & Ricciardi, C. (2019) · Advanced Electronic Materials · doi:10.1002/aelm.201800909 · Cited by 162
Nonlinearity in memristors for neuromorphic dynamic systems
Yang, K., Joshua Yang, J., Huang, R., & Yang, Y. (2022) · Small Science · doi:10.1002/smsc.202100049 · Cited by 151
Self-citationMimicking Classical Conditioning Based on a Single Flexible Memristor
Wu, C., Kim, T. W., Guo, T., Li, F., Lee, D. U., & Yang, J. J. (2016) · Advanced Materials · doi:10.1002/adma.201602890 · Cited by 154
Nanoscale memristive radiofrequency switches
Pi, S., Ghadiri-Sadrabadi, M., Bardin, J. C., & Xia, Q. (2015) · Nature Communications · doi:10.1038/ncomms8519 · Cited by 150
Kim, S. G., Le, Q. V., Han, J. S., Kim, H., Choi, M., Lee, S. A., Kim, T. L., Kim, S. B., Kim, S. Y., & Jang, H. W. (2019) · Advanced Functional Materials · doi:10.1002/adfm.201906686 · Cited by 148
Simultaneous emulation of synaptic and intrinsic plasticity using a memristive synapse
Sung, S. H., Kim, T. J., Shin, H., Im, T. H., & Lee, K. J. (2022) · Nature Communications · doi:10.1038/s41467-022-30432-2 · Cited by 146
Nanoscale electrochemistry using dielectric thin films as solid electrolytes
Valov, I., & Lu, W. D. (2016) · Nanoscale · doi:10.1039/c6nr01383j · Cited by 147
Self-citationCompeting memristors for brain-inspired computing
Kim, S. J., Kim, S., & Jang, H. W. (2020) · iScience · doi:10.1016/j.isci.2020.101889 · Cited by 159
Cellulose Nanofiber Paper as an Ultra Flexible Nonvolatile Memory
Nagashima, K., Koga, H., Celano, U., Zhuge, F., Kanai, M., Rahong, S., Meng, G., He, Y. J., Boeck, J. D., Jurczak, M., et al. (2014) · Scientific Reports · doi:10.1038/srep05532 · Cited by 147
Emulating short-term synaptic dynamics with memristive devices
Berdan, R., Vasilaki, E., Khiat, A., Indiveri, G., Serb, A., & Prodromakis, T. (2016) · Scientific Reports · doi:10.1038/srep18639 · Cited by 148
Evolution of Bio‐Inspired Artificial Synapses: Materials, Structures, and Mechanisms
Yu, H., Wei, H., Gong, J., Han, H., Ma, M., Wang, Y., & Xu, W. (2020) · Small · doi:10.1002/smll.202000041 · Cited by 152
Charge Transition of Oxygen Vacancies during Resistive Switching in Oxide-Based RRAM
Lee, J., Schell, W., Zhu, X., Kioupakis, E., & Lu, W. D. (2019) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.8b18386 · Cited by 142
Self-citationChekol, S. A., Menzel, S., Ahmad, R. W., Waser, R. M., & Hoffmann‐Eifert, S. (2021) · Advanced Functional Materials · doi:10.1002/adfm.202111242 · Cited by 146
Hänsch, W., Raghunathan, A., Roy, K., Chakrabarti, B., Phatak, C., Wang, C., & Guha, S. (2022) · Advanced Materials · doi:10.1002/adma.202204944 · Cited by 167
Roadmap to neuromorphic computing with emerging technologies
Mehonić, A., Ielmini, D., Roy, K., Mutlu, O., Kvatinsky, S., Serrano‐Gotarredona, T., Linares-Barranco, B., Spiga, S., Savel'ev, S. E., Balanov, A. G., et al. (2024) · APL Materials · doi:10.1063/5.0179424 · Cited by 199
Self-citationConduction mechanisms, dynamics and stability in ReRAMs
Wang, C., Wu, H., Gao, B., Zhang, T., Yang, Y., & Qian, H. (2017) · Microelectronic Engineering · doi:10.1016/j.mee.2017.11.003 · Cited by 138
Self-citationYao, Z., Pan, L., Liu, L., Zhang, J., Lin, Q., Ye, Y., Zhang, Z., Xiang, S., & Chen, B. (2019) · Science Advances · doi:10.1126/sciadv.aaw4515 · Cited by 133
“Although the nucleation and growth processes of conducting filaments can be monitored in some devices by means of conductive atomic force microscopy (11) or transmission electron microscopy (12), the switching mechanism for either inorganic or organic RRAMs is still unclear because of the random formation and the diso…”
Tian, H., Chen, H.-Y., Gao, B., Yu, S., Liang, J., Yang, Y., Xie, D., Kang, J., Ren, T.-L., Zhang, Y., et al. (2013) · Nano Letters · doi:10.1021/nl304246d · Cited by 129
Self-citationGuiding the Growth of a Conductive Filament by Nanoindentation To Improve Resistive Switching
Sun, Y., Song, C., Yin, J., Chen, X., Wan, Q., Zeng, F., & Pan, F. (2017) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.7b09710 · Cited by 132
Li, B., Liu, Y., Wan, C., Liu, Z., Wang, M., Qi, D., Yu, J., Cai, P., Meng, X., Zeng, Y., et al. (2018) · Advanced Materials · doi:10.1002/adma.201706395 · Cited by 132
In‐Memory Computing using Memristor Arrays with Ultrathin 2D PdSeO x /PdSe 2 Heterostructure
Li, Y., Chen, S., Yu, Z., Li, S., Xiong, Y., Pam, M., Zhang, Y., & Ang, K. (2022) · Advanced Materials · doi:10.1002/adma.202201488 · Cited by 144
Memristors Empower Spiking Neurons With Stochasticity
Al-Shedivat, M., Naous, R., Cauwenberghs, G., & Salama, K. N. (2015) · IEEE Journal on Emerging and Selected Topics in Circuits and Systems · doi:10.1109/jetcas.2015.2435512 · Cited by 128
“Even though such abrupt behavior is consistent with the experimentally observed single conductive filament growth [32], the precise physics of the filament formation is still under investigation and can vary for different types of memristive devices.”
BackgroundHigh On–Off Ratio Improvement of ZnO-Based Forming-Free Memristor by Surface Hydrogen Annealing
Sun, Y., Yan, X., Zheng, X., Liu, Y., Zhao, Y., Shen, Y., Liao, Q., & Zhang, Y. (2015) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.5b01080 · Cited by 129
Ultrafast and Low-Power 2D Bi 2 O 2 Se Memristors for Neuromorphic Computing Applications
Dong, Z., Hua, Q., Xi, J., Shi, Y., Huang, T., Dai, X., Niu, J., Wang, B., Wang, Z. L., & Hu, W. (2023) · Nano Letters · doi:10.1021/acs.nanolett.3c00322 · Cited by 133
Very Low-Programming-Current RRAM With Self-Rectifying Characteristics
Zhou, J., Cai, F., Wang, Q., Chen, B., Gaba, S., & Lu, W. D. (2016) · IEEE Electron Device Letters · doi:10.1109/led.2016.2530942 · Cited by 122
“Based on these assumptions, from the current ratio of the two cases and the known electrode size of the Cu/aSi/Ta device, the diameter of the Cu filament in the integrated Cu/Al2O3/aSi/Ta device was estimated to be ∼9nm, which agreed well with the filament sizes obtained from direct measurements [18], [20].”
BackgroundMethodSelf-citation2D Layered Materials for Memristive and Neuromorphic Applications
Wang, C., Wang, C., Meng, F., Wang, P., Wang, S., Liang, S., & Miao, F. (2019) · Advanced Electronic Materials · doi:10.1002/aelm.201901107 · Cited by 132
Li, S., Li, B., Feng, X., Chen, L., Li, Y., Huang, L., Fong, X., & Ang, K. (2021) · npj 2D Materials and Applications · doi:10.1038/s41699-020-00190-0 · Cited by 133
You, B. K., Kim, J. M., Joe, D. J., Yang, K., Shin, Y., Jung, Y. S., & Lee, K. J. (2016) · ACS Nano · doi:10.1021/acsnano.6b04578 · Cited by 124
Zhao, F., Cheng, H., Hu, Y., Song, L., Zhang, Z., Jiang, L., & Qu, L. (2014) · Scientific Reports · doi:10.1038/srep05882 · Cited by 126
A 250 mV Cu/SiO2/W Memristor with Half-Integer Quantum Conductance States
Nandakumar, S. R., Minvielle, M., Nagar, S., Dubourdieu, C., & Rajendran, B. (2016) · Nano Letters · doi:10.1021/acs.nanolett.5b04296 · Cited by 124
The plasmonic memristor: a latching optical switch
Hoessbacher, C. B., Fedoryshyn, Y. M., Emboras, A., Melikyan, A., Kohl, M., Hillerkuss, D., Haffner, C., & Leuthold, J. (2014) · Optica · doi:10.1364/optica.1.000198 · Cited by 124
Wang, Z., Xu, H., Zhang, L., Li, X., Ma, J. G., Zhang, X., & Liu, Y. (2013) · Nanoscale · doi:10.1039/c3nr33692a · Cited by 122
Conductive bridging random access memory—materials, devices and applications
Kozicki, M. N., & Barnaby, H. (2016) · Semiconductor Science and Technology · doi:10.1088/0268-1242/31/11/113001 · Cited by 139
“There are also descriptions of reverse growth, in which the filament apparently grows from anode to cathode [46, 117, 125, 126].”
BackgroundXu, X., Cho, E. J., Bekker, L., Talin, A. A., Lee, E., Pascall, A. J., Worsley, M. A., Zhou, J. J., Cook, C. C., Kuntz, J. D., et al. (2022) · Advanced Science · doi:10.1002/advs.202200629 · Cited by 129
2D MoS 2 -Based Threshold Switching Memristor for Artificial Neuron
Dev, D., Krishnaprasad, A., Shawkat, M. S., et al. (2020) · IEEE Electron Device Letters · doi:10.1109/led.2020.2988247 · Cited by 120
“These characteristics also support the Ag diffusion-based switching process [19], [20].”
BackgroundLee, C., Cho, M., Kim, M.-J., Jang, J.-Y., Oh, Y. C., Oh, K., Kim, S., Park, B., Kim, B., Koo, S., et al. (2019) · Scientific Reports · doi:10.1038/s41598-019-38477-y · Cited by 119
Sokolov, A. S., Ali, M., Riaz, R., Abbas, Y., Ko, M. J., & Choi, C. (2019) · Advanced Functional Materials · doi:10.1002/adfm.201807504 · Cited by 121
A Collective Study on Modeling and Simulation of Resistive Random Access Memory
Panda, D., Sahu, P. P., & Tseng, T. (2018) · Nanoscale Research Letters · doi:10.1186/s11671-017-2419-8 · Cited by 133
“It generally involves in-situ observation of the switching process [192] which requires a lot of precision and high-end equipment.”
BackgroundNanoscale resistive switching devices for memory and computing applications
Lee, S. H., Zhu, X., & Lu, W. D. (2020) · Nano Research · doi:10.1007/s12274-020-2616-0 · Cited by 125
Self-citationHighly Compact Artificial Memristive Neuron with Low Energy Consumption
Zhang, Y., He, W., Wu, Y., Huang, K., Shen, Y., Su, J., Wang, Y., Zhang, Z., Ji, X., Li, G., et al. (2018) · Small · doi:10.1002/smll.201802188 · Cited by 117
Oxygen migration induced resistive switching effect and its thermal stability in W/TaOx/Pt structure
Chen, C., Song, C., Yang, J., Zeng, F., & Pan, F. (2012) · Applied Physics Letters · doi:10.1063/1.4730601 · Cited by 116
Zhao, X., Xu, H., Wang, Z., Zhang, L., Ma, J., & Liu, Y. (2015) · Carbon · doi:10.1016/j.carbon.2015.04.031 · Cited by 115
You, B. K., Park, W. I., Kim, J. M., Park, K., Seo, H. K., Lee, J. Y., Jung, Y. S., & Lee, K. J. (2014) · ACS Nano · doi:10.1021/nn503713f · Cited by 119
Versatile memristor for memory and neuromorphic computing
Guo, T., Pan, K., Jiao, Y., Sun, B. T., Du, C., Mills, J. P., Chen, Z., Zhao, X., Wei, L., Zhou, Y., et al. (2022) · Nanoscale Horizons · doi:10.1039/d1nh00481f · Cited by 120
Impact of the Mechanical Stress on Switching Characteristics of Electrochemical Resistive Memory
Ambrogio, S., Balatti, S., Choi, S., & Ielmini, D. (2014) · Advanced Materials · doi:10.1002/adma.201306250 · Cited by 123
Luo, C., Wang, C., Wu, X. Y., Zhang, J., & Chu, J. (2017) · Small · doi:10.1002/smll.201604259 · Cited by 116
A Native Stochastic Computing Architecture Enabled by Memristors
Knag, P. C., Lu, W. D., & Zhang, Z. (2014) · IEEE Transactions on Nanotechnology · doi:10.1109/tnano.2014.2300342 · Cited by 122
“…that provides a large dynamic range between logic levels, the change in resistance is associated with the formation and rupture of a dominant , nanoscale conducting filament (either caused by metallic bridge formation [7], [8], [24] or by stoichiometric change in the switching material [25], [26]).”
BackgroundSelf-citationMemristive Devices for New Computing Paradigms
Im, I. H., Kim, S. J., & Jang, H. W. (2020) · Advanced Intelligent Systems · doi:10.1002/aisy.202000105 · Cited by 129
Wijesinghe, P., Ankit, A., Sengupta, A., & Roy, K. (2018) · IEEE Transactions on Emerging Topics in Computational Intelligence · doi:10.1109/tetci.2018.2829924 · Cited by 113
“At this point, the active electrode dissolution transpires and cations from the active electrode start migrating towards the inert electrode where it gets electro-crystalized, forming a metal filament (termed as the ‘forming process’[30]).”
BackgroundMethodEmerging synaptic devices: from two-terminal memristors to multiterminal neuromorphic transistors
Jiang, S., Nie, S., He, Y., Liu, R., Chen, C., & Wan, Q. (2019) · Materials Today Nano · doi:10.1016/j.mtnano.2019.100059 · Cited by 129
Conductance Quantization in Resistive Random Access Memory
Li, Y., Long, S., Liu, Y., Hu, C., Teng, J., Liu, Q., Lv, H., Suñé, J., & Liu, M. (2015) · Nanoscale Research Letters · doi:10.1186/s11671-015-1118-6 · Cited by 125
“The dimension of the CF can be electrically modulated to be in the order of several tens to a few nanometers, which has been evidenced by the observation of high-resolution transmission electron microscopy (HRTEM) [20, 48–60], scanning TEM (STEM) [59], and atomic force microscopy (AFM) [61–63].”
MethodField-Induced Percolation of Polar Nanoregions in Relaxor Ferroelectrics
Prosandeev, S. A., Wang, D., Akbarzadeh, A. R., et al. (2013) · Physical Review Letters · doi:10.1103/physrevlett.110.207601 · Cited by 110
Menzel, S., Kaupmann, P., & Waser, R. M. (2015) · Nanoscale · doi:10.1039/c5nr02258d · Cited by 108
Building Neuromorphic Circuits with Memristive Devices
Chang, T., Yang, Y., & Lu, W. D. (2013) · IEEE Circuits and Systems Magazine · doi:10.1109/mcas.2013.2256260 · Cited by 120
Self-citationElectrically Controlled Plasmonic Switches and Modulators
Emboras, A., Hoessbacher, C. B., Haffner, C., Heni, W., Koch, U., Ma, P., Fedoryshyn, Y. M., Niegemann, J., Haffner, C., & Leuthold, J. (2014) · IEEE Journal of Selected Topics in Quantum Electronics · doi:10.1109/jstqe.2014.2382293 · Cited by 109
The strategies of filament control for improving the resistive switching performance
Li, T., Yu, H., Chen, S. H. Y., Zhou, Y., & Han, S. (2020) · Journal of Materials Chemistry C · doi:10.1039/d0tc03639k · Cited by 113
Kang, J., Kim, T.-Y., Hu, S., Kim, J., Kwak, J. Y., Park, J., Park, J., Kim, I., Lee, S., Kim, S., et al. (2022) · Nature Communications · doi:10.1038/s41467-022-31804-4 · Cited by 132
“It is widely known that packing densities of amorphous switching matrix critically in fl uence the cationic transport process of CBRAM 2,5,23 ; low-density amorphous fi lms demonstrate high cation mobility ( μ ), where the injected cations reach the counter electrode in a short time and reduce at the…”
BackgroundPolymeric Memristor Based Artificial Synapses with Ultra‐Wide Operating Temperature
Li, J., Qian, Y., Li, W., Yu, S., Ke, Y., Qian, H., Lin, Y., Hou, C., Shyue, J., Zhou, J. J., et al. (2023) · Advanced Materials · doi:10.1002/adma.202209728 · Cited by 115
Wang, C., He, W., Tong, Y., & Zhao, R. J. (2016) · Scientific Reports · doi:10.1038/srep22970 · Cited by 111
Yang, F., Sun, L., Duan, Q., Dong, H., Jing, Z., Yang, Y., Li, R., Zhang, X., Hu, W., & Chua, L. O. (2021) · SmartMat · doi:10.1002/smm2.1022 · Cited by 109
“Principally, the fine adjustment of the resistance state is attributed to the precise control of the quantity or width of CFs in memristors.(9,20,24,28) Indeed, thirty‐level resistance states are achieved by programming reset voltage sweeps from 3.”
BackgroundSelf-citationVertically integrated spiking cone photoreceptor arrays for color perception
Wang, X., Chen, C., Zhu, L. Q., Shi, K., Peng, B., Zhu, Y., Mao, H., Long, H., Ke, S., Fu, C., et al. (2023) · Nature Communications · doi:10.1038/s41467-023-39143-8 · Cited by 114
“The formation of CFs is dominated by cation migrationand redox processes 34 – 39 .”
BackgroundLee, J., Jeong, B. H., Kamaraj, E., Kim, D., Kim, H., Park, S., & Park, H. J. (2023) · Nature Communications · doi:10.1038/s41467-023-41419-y · Cited by 132
“With this medium, the memristor is designed to have the fi lamentary redox reaction of active metal cation (e.g., Ag and Cu) for tuning its resistance, which has been known to provide superior analog switching characteristics due to the high mobility of metal ions 52,53 .”
Nanomaterials for Flexible Neuromorphics
Ding, G., Li, H., Zhao, J., Zhou, K., Zhai, Y., Lv, Z., Zhang, M., Yan, Y., Han, S., & Zhou, Y. (2024) · Chemical Reviews · doi:10.1021/acs.chemrev.4c00369 · Cited by 114
Controllable Formation of Nanofilaments in Resistive Memories via Tip‐Enhanced Electric Fields
Shin, K., Kim, Y., Antolinez, F. V., Ha, J. S., Lee, S., & Park, J. H. (2016) · Advanced Electronic Materials · doi:10.1002/aelm.201600233 · Cited by 104
Hu, W., Jiang, J., Xie, D., Wang, S., Bi, K., Duan, H., Yang, J., & He, J. (2018) · Nanoscale · doi:10.1039/c8nr04136a · Cited by 102
Shi, C., Wang, J., Sushko, M. L., Qiu, W., Yan, X., & Liu, X. Y. (2019) · Advanced Functional Materials · doi:10.1002/adfm.201904777 · Cited by 109
Zahoor, F., Hussin, F. A., Bature, U. I., Gupta, S., Khanday, F. A., Chattopadhyay, A., & Abbas, H. (2023) · Discover Nano · doi:10.1186/s11671-023-03775-y · Cited by 120
“The application of higher voltage generally enables the device to switch exponentially faster [75], but there are some undesirable effects of applying higher voltages specifically in terms of power consumption and device reliability.”
BackgroundRoom-temperature air-stable spin transport in bathocuproine-based spin valves
Sun, X., Gobbi, M., Bedoya‐Pinto, A., Txoperena, O., Golmar, F., Llopis, R., Chuvilin, A. L., Casanova, F., & Hueso, L. E. (2013) · Nature Communications · doi:10.1038/ncomms3794 · Cited by 104
Wu, Q., Banerjee, W., Cao, J., Ji, Z., Li, L., & Liu, M. (2018) · Applied Physics Letters · doi:10.1063/1.5030780 · Cited by 100
Overview of emerging memristor families from resistive memristor to spintronic memristor
Wang, L., Yang, C., Wen, J., Gai, S., & Peng, Y.-X. (2015) · Journal of Materials Science Materials in Electronics · doi:10.1007/s10854-015-2848-z · Cited by 104
Metallic to hopping conduction transition in Ta2O5−x/TaOy resistive switching device
Zhang, Y., Deng, N., Wu, H., Yu, Z., Zhang, J., & Qian, H. (2014) · Applied Physics Letters · doi:10.1063/1.4893325 · Cited by 98
Formation process of conducting filament in planar organic resistive memory
Gao, S., Song, C., Chen, C., Zeng, F., & Pan, F. (2013) · Applied Physics Letters · doi:10.1063/1.4802092 · Cited by 97
Resistive switching and conductance quantization in Ag/SiO2/indium tin oxide resistive memories
Gao, S., Chen, C., Zhai, Z., Liu, H. Y., Lin, Y., Li, S. Z., Lu, S., Wang, G. Y., Song, C., Zeng, F., et al. (2014) · Applied Physics Letters · doi:10.1063/1.4893277 · Cited by 99
Yuan, F., Zhang, Z., Liu, C., Zhou, F., Yau, H. M., Lu, W., Qiu, X., Wong, H.-S. P., Dai, J., & Chai, Y. (2017) · ACS Nano · doi:10.1021/acsnano.7b00783 · Cited by 99
Self-citationBipolar Electrochemical Mechanism for Mass Transfer in Nanoionic Resistive Memories
Tian, X., Yang, S., Zeng, M., Wang, L., Wei, J., Xu, Z. Q., Wang, W., & Bai, X. (2014) · Advanced Materials · doi:10.1002/adma.201400127 · Cited by 98
A Low‐Current and Analog Memristor with Ru as Mobile Species
Yoon, J. H., Zhang, J., Lin, P., Upadhyay, N. K., Yan, P., Liu, Y., Xia, Q., & Yang, J. J. (2020) · Advanced Materials · doi:10.1002/adma.201904599 · Cited by 98
Two‐Dimensional Oxides: Multifunctional Materials for Advanced Technologies
Pacchioni, G. (2012) · Chemistry - A European Journal · doi:10.1002/chem.201201117 · Cited by 96
Enhanced stability of filament-type resistive switching by interface engineering
Zhu, Y., Zheng, K., Wu, X., & Ang, L. K. (2017) · Scientific Reports · doi:10.1038/srep43664 · Cited by 93
Long-term and short-term plasticity of Ta2O5/HfO2 memristor for hardware neuromorphic application
Ryu, J., Mahata, C., & Kim, S. (2020) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2020.156675 · Cited by 94
A Monolayer Leaky Integrate‐and‐Fire Neuron for 2D Memristive Neuromorphic Networks
Song, H., Ji, X., Zhong, S., Pang, K. Y., Lim, K. G., Chong, T. C., & Zhao, R. J. (2020) · Advanced Electronic Materials · doi:10.1002/aelm.201901335 · Cited by 92
Conductive-bridging random access memory: challenges and opportunity for 3D architecture
Jana, D., Roy, S., Panja, R., Dutta, M., Rahaman, S. Z., Mahapatra, R., & Maikap, S. (2015) · Nanoscale Research Letters · doi:10.1186/s11671-015-0880-9 · Cited by 102
“(e) Schematic diagram of the nanofilament growth process in an a-Si CBRAM device [54].”
MethodAlcohol‐Mediated Resistance‐Switching Behavior in Metal–Organic Framework‐Based Electronic Devices
Liu, Y., Wang, H., Shi, W., Zhang, W., Yu, J., Chandran, B. K., Cui, C., Zhu, B., Liu, Z., Li, B., et al. (2016) · Angewandte Chemie International Edition · doi:10.1002/anie.201602499 · Cited by 92
Advanced analytical electron microscopy for lithium-ion batteries
Qian, D., Ma, C., More, K. L., et al. (2015) · NPG Asia Materials · doi:10.1038/am.2015.50 · Cited by 91
Wang, Y., Kang, K.-M., Kim, M., Lee, H., Waser, R. M., Wouters, D. J., Dittmann, R., Yang, J. J., & Park, H. (2019) · Materials Today · doi:10.1016/j.mattod.2019.06.006 · Cited by 96
Du, H., Jia, C., Koehl, A., Barthel, J., Dittmann, R., Waser, R. M., & Mayer, J. (2017) · Chemistry of Materials · doi:10.1021/acs.chemmater.7b00220 · Cited by 92
Memristive Devices and Networks for Brain‐Inspired Computing
Zhang, T., Ke, Y., Xu, X., Cai, Y., Yang, Y., & Huang, R. (2019) · physica status solidi (RRL) - Rapid Research Letters · doi:10.1002/pssr.201900029 · Cited by 95
Self-citationRobust DNA‐Bridged Memristor for Textile Chips
Xu, X., Zhou, X., Wang, T., Shi, X., Liu, Y., Zuo, Y., Xu, L., Wang, M., Hu, X., Yang, X., et al. (2020) · Angewandte Chemie International Edition · doi:10.1002/anie.202004333 · Cited by 89
Metadata
- Authors
- Yang, Y., Gao, P., Gaba, S., Chang, T., Pan, X., & Lu, W.
- Affiliations
- University of Michigan (US)
- Corresponding author
- Lu, Wei
- Venue
- Nature Communications
- Published
- 2012-03-13
- Volume
- 3
- Issue
- 1
- Pages
- 732-732
- ISSN
- 2041-1723 (ISSN-L)
- OpenAlex
- W2043707274
- Cited by
- 1,208
- References
- 32
- Citations by year
- 2026: 68 · 2025: 69 · 2024: 92 · 2023: 84 · 2022: 95 · 2021: 85 · 2020: 101 · 2019: 100 · 2018: 89 · 2017: 95 · 2016: 88 · 2015: 81 · 2014: 71 · 2013: 68 · 2012: 21
- FWCI
- 49.24
- Type
- journal article
- Language
- en
- Open access
- bronze
- doi.org
- Licence
- www.springernature.com/gp/researchers/text-and-data-mining (tdm)
- www.springernature.com/gp/researchers/text-and-data-mining (vor)
- Locations
- Nature Communications (publishedVersion)
- PubMed (publishedVersion)
- RePEc: Research Papers in Economics (submittedVersion)
- Funders
- National Science Foundation (0723032, 0907191, 0954621)
- Defense Advanced Research Projects Agency (HRL0011-09-C-001)
- Division of Materials Research (0723032, DMR-0723032)
- Division of Electrical, Communications and Cyber Systems (ECCS-0954621)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Advanced Memory and Neural Computing
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Ferroelectric and Negative Capacitance Devices
- Physical Sciences › Materials Science › Materials Chemistry › Phase-change materials and chalcogenides
- Keywords
- resistive switching, memristors, electrochemical metallization, cation transport, dielectric films, non-volatile memory, in situ transmission electron microscopy
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-09-30, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-09-30 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.