Cited by 673Electric Motor Design and AnalysisElectric and Hybrid Vehicle TechnologiesSensorless Control of Electric Motors

The DOI matches its Crossref record; 83 of the 87 references it cites were found in a registry or an index.

Electrical Motor Drivelines in Commercial All-Electric Vehicles: A Review

Open access

de Santiago, Juan, Bernhoff, Hans, Ekergård, Boel, Eriksson, Sandra, Ferhatovic, Senad, Waters, Rafael, Leijon, Mats·2012·IEEE Transactions on Vehicular Technology

DOI 10.1109/tvt.2011.2177873

Open this paper in CoChat — free account

Abstract

This paper presents a critical review of the drivelines in all-electric vehicles (EVs). The motor topologies that are the best candidates to be used in EVs are presented. The advantages and disadvantages of each electric motor type are discussed from a system perspective. A survey of the electric motors used in commercial EVs is presented. The survey shows that car manufacturers are very conservative when it comes to introducing new technologies. Most of the EVs on the market mount a single induction or permanent-magnet (PM) motor with a traditional mechanic driveline with a differential. This paper illustrates that comparisons between the different motors are difficult by the large number of parameters and the lack of a recommended test scheme. The authors propose that a standardized drive cycle be used to test and compare motors.

Integrity signals

Registry

Crossref · 10.1109/tvt.2011.2177873

Cites

83 of 83 references verified0 citation errors · 0 not checkable

Statistics

Recomputing p-values needs the paper’s full text.

Claims the paper makes

We couldn’t retrieve this paper’s full text, so its claims and self-check weren’t run. The registry and citation checks still apply.

Claims other papers make about this one

Each is checked against this paper’s own text: does it say what the citing paper says it does?

Multiphase Electric Machines for Variable-Speed Applications
LEVI, E. (2008) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2008.918488 · Cited by 2,162
Multiphase induction motor drives – a technology status review
LEVI, E., Bojoi, R. I., Profumo, F., Toliyat, H. A., & Williamson, S. (2007) · IET Electric Power Applications · doi:10.1049/iet-epa:20060342 · Cited by 1,620
Overview of Permanent-Magnet Brushless Drives for Electric and Hybrid Electric Vehicles
Chau, K. T., Chan, C. C., & Liu, C. (2008) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2008.918403 · Cited by 1,499
Design considerations for a contactless electric vehicle battery charger
Wang, C.-S., Stielau, O., & Covic, G. (2005) · IEEE transactions on industrial electronics (1982. Print) · doi:10.1109/tie.2005.855672 · Cited by 1,474
The state of the art of electric and hybrid vehicles
Chan, C. C. (2002) · Proceedings of the IEEE · doi:10.1109/5.989873 · Cited by 1,102
Electric, Hybrid, and Fuel-Cell Vehicles: Architectures and Modeling
Chan, C. C., Bouscayrol, A., & Chen, K. (2010) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2009.2033605 · Cited by 792
Batteries and Ultracapacitors for Electric, Hybrid, and Fuel Cell Vehicles
Burke, A. F. (2007) · Proceedings of the IEEE · doi:10.1109/jproc.2007.892490 · Cited by 790
Electric Motor Drive Selection Issues for HEV Propulsion Systems: A Comparative Study
Zeraoulia, M., Benbouzid, M., & Diallo, D. (2006) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2006.878719 · Cited by 692
Beyond batteries: an examination of the benefits and barriers to plug-in hybrid electric vehicles (PHEVs) and a vehicle-to-grid (V2G) transition
Sovacool, B. K., & Hirsh, R. F. (2009) · Energy Policy · doi:10.1016/j.enpol.2008.10.005 · Cited by 630
An overview of power electronics in electric vehicles
Chan, C. C., & Chau, K. T. (1997) · IEEE Transactions on Industrial Electronics · doi:10.1109/41.557493 · Cited by 488

Show all 87 references

Research works printed but not linked: 14

0, A rotary electric machine a rotor for a such and a Vehicle/craft with such a machine
2008, Michelin Active Wheel Press Kit 2008 Paris Motor Show
harris, 2010, REV SAE Front Drive Final Year Project Thesis School of Mechanical Engineering Univ Western Australia
gieras, 2002, Permanent Magnet Motor Technology Revised
fenton, 2000, Lightweight Electric/Hybrid Vehicle Design Automotive Engineering Series
2010, Autonomous modular vehicle wheel assembly
2010, The 2010 Paris Motor Show Press Release
2011, One Million Electric Vehicles By 2015 Feb 2011 Status Report
curley, 2010, The Britannica Guide to Inventions That Changed the Modern World, 162
0, Presentation of the Swedish National Road Administration (SNRA)
2006, Nuclear Power Reactors in the World
situ, 2009, Electric vehicle development: The past, present and future, Proc 3rd Int Conf PESA, 1
2011, White Paper Roadmap to a Single European Transport AreaTowards a Competitive and Resource Efficient Transport System
santiago, 2010, Comparison between axial and radial flux PM coreless machines for flywheel energy storage, J Elect Syst, 6, 1

Sorted by citations

Items 401–500 of 673

Analytical and Experimental Investigations of Magnetostriction Influence on Strain Measurement in Switched Reluctance Machines
Cai, Y., Sobue, H., Wiguna, C. A., Chibá, A., Senda, K., & Yoshizaki, S. (2021) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce47101.2021.9595173 · Cited by 4
Global quasi-Mittag–Leffler stability of distributed-order BLDCM system
Zhong, X., Shahidehpour, M., & Zou, Y. (2022) · Nonlinear Dynamics · doi:10.1007/s11071-022-07304-x · Cited by 4
Wound Field Synchronous Drive Cycle Current Parameters Optimization: A Metamodel-Based Approach
Mazloum, R., Hlioui, S., Laurent, L., Belhadi, M., Mermaz-Rollet, G., & Gabsi, M. (2022) · International Conference on Electrical Machines (ICEM) · doi:10.1109/icem51905.2022.9910948 · Cited by 4
Improved PI-Controller Of Switched Reluctance Motor For Torque Ripple Minimization In Electric Vehicle Applications
azazy, B., ABDEL-KADER, F., alsherif, M., & Abdelqawee, I. M. (2023) · Engineering Research Journal - Faculty of Engineering (Shoubra) · doi:10.21608/erjsh.2022.171006.1104 · Cited by 4
Yaw Rate Control and Actuator Fault Detection and Isolation for a Four Wheel Independent Drive Electric Vehicle
Bagheri, N., & Alipour, H. (2017) · DOAJ (DOAJ: Directory of Open Access Journals) · doi:10.22098/joape.2017.551 · Cited by 4
Regenerative Fuzzy Brake Blending Strategy on Benchmark Electric Vehicle: the FIAT 500e
Favilli, T., Pugi, L., Berzi, L., Pierini, M., & Tobia, N. (2020) · IEEE International Conference on Environment and Electrical Engineering and IEEE Industrial and Commercial Power Systems Europe (EEEIC / I&CPS Europe) · doi:10.1109/eeeic/icpseurope49358.2020.9160584 · Cited by 4
Multiphysic Design and Modeling of Rotating Electrical Machines
Darmani, M. A., Vaschetto, S., & Cavagnino, A. (2021) · Annual Conference of the IEEE Industrial Electronics Society (IECON) · doi:10.1109/iecon48115.2021.9589145 · Cited by 4
A new topology for a photovoltaic based range extender
Neuburger, M., Schmidt, G., & Neuberger, N. (2014) · IEEE International Conference on Industrial Technology (ICIT) · doi:10.1109/icit.2014.6894981 · Cited by 4
Effect of armature reaction on the core losses of the permanent magnet synchronous motor
Ruuskanen, V. (2016) · Electrical Engineering · doi:10.1007/s00202-016-0401-6 · Cited by 4
Design of Inductive Power Transmission into the Rotor of an Externally Excited Synchronous Machine
Littau, A., Wagner, B., Köhler, S., Dietz, A., & Weber, S. (2014) · mediaTUM – the media and publications repository of the Technical University Munich (Technical University Munich) · Cited by 4
A Non-segmental Outer Rotor Switched Reluctance Machine for In-Wheel Electric Vehicle Application
Hanaeinejad, V., & Abbasian, M. (2019) · Iranian Journal of Science and Technology Transactions of Electrical Engineering · doi:10.1007/s40998-019-00192-9 · Cited by 4
Modeling and Control of Hybrid Electric Vehicle
Flah, A., Kraiem, H., & Sbita, L. (2021) · Advances in systems analysis, software engineering, and high performance computing book series · doi:10.4018/978-1-7998-5788-4.ch021 · Cited by 4
Permanent magnet synchronous machines
González-Prieto, Á., González‐Prieto, I., Aciego, J. J., Bermúdez, M., & Duran, M. J. (2022) · Elsevier eBooks · doi:10.1016/b978-0-12-821204-2.00021-0 · Cited by 4
Advancements in Electrical Machines for E-Mobility
Bárta, J. (2025) · International Conference on Electrical, Electronic and Computing Engineering (IcETRAN) · doi:10.1109/icetran66854.2025.11114258 · Cited by 3
Optimizing Ride Comfort and Stability in In-Wheel Motor Drive Electric Vehicles: A Correlated Semi-Active Suspension System with Kalman Filter and Spring-Type Analysis
Gad, A. S., Jabeen, S. D., El-Zomor, H. M., Tolba, M., & Elamy, M. I. (2026) · SAE International journal of vehicle dynamics, stability, and NVH · doi:10.4271/10-10-04-0030 · Cited by 3
Development of a Power Transformer for a Fast Charging Station
Volskiy, N., & Krapivnoi, M. (2023) · National Conference on Electrical and Electronics Engineering (ELECO) · doi:10.1109/iceee59925.2023.00074 · Cited by 3
Optimal drive cycle current supply of a wound field automotive electrical machine using surrogate models
Mazloum, R., Hlioui, S., Laurent, L., Belhadi, M., Mermaz-Rollet, G., & Gabsi, M. (2024) · Science and Technology for Energy Transition · doi:10.2516/stet/2023041 · Cited by 3
Simulation and validation of hydraulic track drive systems for electrification of heavy-duty machinery
Coyle, H., Young, C., Anderson, N., Johnston, L., & Gilmour, R. (2025) · Scientific Reports · doi:10.1038/s41598-025-17449-5 · Cited by 3
Basic Examination for a Hybrid Excitation Motor with a Field Winding on a Rotor
Nakazawa, R., Takemoto, M., Ogasawara, S., & Orikawa, K. (2020) · Journal of the Japan Society of Applied Electromagnetics and Mechanics · doi:10.14243/jsaem.28.206 · Cited by 3
Analysis of Technical Capabilities, Methodology and Test Results of a Light-Commercial Vehicle Conversion to Battery Electric Powertrain
Bielaczyc, P., Sala, R., & Meinicke, T. (2021) · Energies · doi:10.3390/en14041119 · Cited by 3
Compensating the performance of permanent magnet synchronous machines for fully electric vehicle using LPV control
Muazzam, H., Ishak, M. K., & Hanif, A. (2021) · Bulletin of Electrical Engineering and Informatics · doi:10.11591/eei.v10i4.2946 · Cited by 3
Parameter matching and simulation analysis of power system of pure electric vehicle
Geng, J., & Chi, Q. (2021) · Journal of Physics Conference Series · doi:10.1088/1742-6596/2076/1/012091 · Cited by 3
Examination for a Hybrid Excitation Motor with Reverse Saliency while Having a Field Winding on a Rotor
Nakazawa, R., Takemoto, M., Ogasawara, S., & Orikawa, K. (2021) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce47101.2021.9595816 · Cited by 3
Optimal design and implementation of a drivetrain for an ultra-light electric vehicle
Hofman, I., Sergeant, P., den Bossche, A. V., Köroğlu, S., & Kesler, S. (2016) · International Journal of Vehicle Design · doi:10.1504/ijvd.2016.080592 · Cited by 3
MTPA Based Direct Torque Control for Energy-Efficient Operation of Induction Motors in Electric Vehicles
Jose, S., & Rajeevan, P. P. (2021) · IEEE Transportation Electrification Conference (ITEC-India) · doi:10.1109/itec-india53713.2021.9932448 · Cited by 3
Technical and Economic Analysis to Select Suitable Design Parameters of an E-Machine for Electric Commercial Vehicles
Kampker, A., Heimes, H. H., Dorn, B., Brans, F., Gómez, J. G. D., & Sharma, C. (2023) · Vehicles · doi:10.3390/vehicles5010005 · Cited by 3
Performance Comparison of Six-Phase PM Machine with Several Winding Layouts for EV Applications
Abdel-Wahed, A. T., Metwly, M. Y., Hemeida, A., Abdel-Khalik, A. S., Hamad, M. S., & Ahmed, S. (2023) · IEEE Conference on Power Electronics and Renewable Energy (CPERE) · doi:10.1109/cpere56564.2023.10119595 · Cited by 3
Assessing the Dynamic Performance and Energy Efficiency of Pure Electric Car with Optimal Gear Shifting
Zhao, Q., Zhou, S., Yue, Y., Liu, B., Xie, Q., & Zhang, N. (2023) · Energies · doi:10.3390/en16166044 · Cited by 3
Field Weakening Control of a Permanent Magnet Synchronous Motor
Maulana, R., Sidik, Y. F., & Ali, H. R. (2023) · doi:10.1109/icitee59582.2023.10317741 · Cited by 3
A multi-objective coupling parameter hierarchical optimization framework for a novel dual-motor powertrain system of electric vehicle
Lin, C., Liu, H., Yu, X., & Xie, P. (2024) · Proceedings of the Institution of Mechanical Engineers Part D Journal of Automobile Engineering · doi:10.1177/09544070241257556 · Cited by 3
Dynamic Models for Electrically Excited Synchronous Machines based on Flux-to-Current and Current-to-Inductance Maps
Perilli, L., Graffeo, F., Rubino, S., & Vaschetto, S. (2024) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce55643.2024.10861168 · Cited by 3
Thermal Control Compensation of Induction Motor Drive in Electrified Powertrain
Ali, S. M. N., Hossain, M. J., Sharma, V., & Kashif, M. (2020) · IEEE Conference on Technologies for Sustainability · doi:10.1109/sustech47890.2020.9150527 · Cited by 3
Design and implementation of a three-wheel multi-purpose electric vehicle with finite elements analysis
ALVALI, G. T., BALBAY, A., Güneş, S., Yenipınar, B., Catalbas, C., & ŞİŞMAN, T. (2021) · International Journal of Automotive Science And Technology · doi:10.30939/ijastech..871684 · Cited by 3
Efficiency Measuring of Electric Drive with Traction Synchronous Motor with Permanent Magnets
Břoušek, J., Krcmar, L., & Rydlo, P. (2021) · IEEE International Workshop of Electronics, Control, Measurement, Signals and their Application to Mechatronics (ECMSM) · doi:10.1109/ecmsm51310.2021.9468836 · Cited by 3
BLDC Motor Control using a Complex Programmable Logic Device with Hall-Sensors
Sachruddin, M. F., Samman, F. A., & Sadjad, R. S. (2021) · International Conference on Smart-Green Technology in Electrical and Information Systems (ICSGTEIS) · doi:10.1109/icsgteis53426.2021.9650433 · Cited by 3
Piecewise Affine Maximum Torque per Ampere for the Wound Rotor Synchronous Machine
Steyaert, B., Swint, E., Pennington, W. W., & Preindl, M. (2022) · IEEE Transportation Electrification Conference and Expo · doi:10.1109/itec53557.2022.9814034 · Cited by 3
Low-computational-complexity algorithm for current predictive control of an externally excited synchronous machine
Carpiuc, S., & Lazǎr, C. (2013) · International Conference on System Theory, Control and Computing (ICSTCC) · doi:10.1109/icstcc.2013.6688943 · Cited by 3
Induction machine models for efficiency studies in EV design applications
Aguilera, F., de la Barrera, P. M., & Angelo, C. H. D. (2012) · IEEE International Conference on Industry Applications · doi:10.1109/induscon.2012.6452497 · Cited by 3
An inverter dead-time feedforward compensation scheme for PMSM sensorless drive operation
Diallo, D., Arias, A., & Cathelin, J. (2014) · International Conference on Green Energy (ICGE) · doi:10.1109/icge.2014.6835438 · Cited by 3
Cost estimation of electric traction machine and gearbox for a hybrid vehicle application
Domingues-Olavarría, G., Reinap, A., & Alaküla, M. (2014) · International Electric Drives Production Conference · doi:10.1109/edpc.2014.6984410 · Cited by 3
Actuation of ship stabilizing fins by a permanent magnet linear synchronous motor drive servoed to the hydraulic motor
Zito, D., Bruzzese, C., Rafiei, M., Santini, E., Mazzuca, T., Tessarolo, A., & Lipardi, G. (2016) · International Conference on Ecological Vehicles and Renewable Energies (EVER) · doi:10.1109/ever.2016.7476393 · Cited by 3
Quantification of External Heat Load on HEV Integrated IPMs Using the Air-Gap Shear Stress
Paar, C., & Muetze, A. (2017) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2017.2656069 · Cited by 3
Performance comparison of IPMSMs using a low iron loss material for automotive application
Suzuki, S., Morimoto, S., Sanada, M., & Inoue, Y. (2016) · International Conference on Electrical Machines and Systems (ICEMS) · Cited by 3
A new topology for an unidirectional galvanic isolated combined converter
Neuburger, M., Seeger, W., Bertele, F., Ammann, U., & Thrimawithana, D. J. (2016) · IEEE Annual Southern Power Electronics Conference · doi:10.1109/spec.2016.7846090 · Cited by 3
Project, design and tests of in-wheel outer-rotor PMSM for electric car application. Part 1
SZCZYPIOR, J. (2017) · PRZEGLĄD ELEKTROTECHNICZNY · doi:10.15199/48.2017.02.30 · Cited by 3
Adding Electric Vehicle Modeling Capability to an Agent-Based Transport Simulation
Waraich, R. A., Georges, G., Galus, M. D., & Axhausen, K. W. (2013) · Advances in data mining and database management book series · doi:10.4018/978-1-4666-4920-0.ch014 · Cited by 3
Permanent Magnet Synchronous Machines
Eriksson, S. (2019) · MDPI eBooks · doi:10.3390/books978-3-03921-351-1 · Cited by 3
Self-citation
Modeling, simulation, and experiments on waste kinetic energy utilization
Afify, R. S., Mansour, M., Saber, E., & Ibrahim, K. A. (2022) · Energy Reports · doi:10.1016/j.egyr.2022.06.106 · Cited by 3
Vector Control of IPMSM used in Electric Vehicles
Muazzam, H., Ishak, M. K., Hanif, A., Bhatti, A. I., Isa, N. A. M., & Mahyuddin, M. N. (2022) · Asian Control Conference (ASCC) · doi:10.23919/ascc56756.2022.9828076 · Cited by 3
System Performance Comparison of Direct Torque Control Strategies Based on Flux Linkage and DC-Link Voltage for EV Drivetrains
Prabhakar, K. K., Reddy, C. U., Singh, A. K., & Kumar, P. (2019) · SAE International journal of alternative powertrains · doi:10.4271/08-08-02-0007 · Cited by 3
Critical evaluation of the battery electric vehicle for sustainable mobility
Milligan, R. (2026) · Research Output (Edinburgh Napier University) · doi:10.17869/enu.978220 · Cited by 3
High-Efficiency e-Powertrain Topology by Integrating Open-End Winding and Winding Changeover for Improving Fuel Economy of Electric Vehicles
Cha, K.-S., Kim, J.-H., Hwang, S.-W., Lim, M., & Park, S.-H. (2024) · Mathematics · doi:10.3390/math12213415 · Cited by 2
Adaptive Fuzzy-Based Field-Oriented Control for Enhanced Performance of Permanent Magnet Synchronous Motors
Priya, B., Kaur, R., & Mukkapati, A. B. K. (2025) · Journal of Control Automation and Electrical Systems · doi:10.1007/s40313-025-01221-1 · Cited by 2
Comparative study of constant power speed range of three permanent magnet brushless machines with different d-axis inductance for electric vehicles
Gu, W., Quan, L., Zhu, X., Du, Y., & Shi, K. (2015) · International Conference on Electrical Machines and Systems (ICEMS) · doi:10.1109/icems.2015.7384971 · Cited by 2
Influence of the Magnetic Bridges on the Flux Focusing Type Axial Flux Permanent Magnet Motor
Syed, Q. A. S., & Hahn, I. (2018) · IEEE Electrical Power and Energy Conference (EPEC) · doi:10.1109/epec.2018.8598318 · Cited by 2
Optimal Design and Analysis of Interior Permanent Magnet Motor for High-thrust Drone
Lee, H.-S., Cha, H.-R., Yang, S.-H., Kim, D.-H., Lee, G.-S., & Kim, H.-W. (2019) · IEEE Transportation Electrification Conference and Expo, Asia-Pacific (ITEC Asia-Pacific) · doi:10.1109/itec-ap.2019.8903660 · Cited by 2
Eddy Current Losses in Solid Pole Shoes in a Two-Pole Permanent Magnet Motor
Ekergård, B., & Leijon, M. (2021) · Engineering · doi:10.4236/eng.2021.1310038 · Cited by 2
Self-citation
Traction and Charging Systems for an Electric Motorcycle
Carvalho, J., Sousa, T. J. C., & Pedrosa, D. (2022) · Lecture notes of the Institute for Computer Sciences, Social Informatics and Telecommunications Engineering · doi:10.1007/978-3-030-97027-7_10 · Cited by 2
A Control Method of Switched Reluctance Motor Based on Non-unity TSF and Adaptive Overlapping Angle
Huang, C., Cao, W., Sun, Y., Chen, Z., & Zhang, W. (2023) · Progress In Electromagnetics Research C · doi:10.2528/pierc23021802 · Cited by 2
Real Time Core Loss Estimation for the Wound Rotor Synchronous Machine
Steyaert, B., Swint, E., Pennington, W. W., & Preindl, M. (2023) · IEEE International Symposium on Diagnostics for Electrical Machines, Power Electronics and Drives (SDEMPED) · doi:10.1109/sdemped54949.2023.10271415 · Cited by 2
Design of Hairpin Winding and Random Winding Stators for High Speed Heavy-Duty Traction Motor
Jiang, J., Zou, T., Rocca, A. L., Rocca, S. L., Liu, C., Xu, Z., Gerada, C., Zhu, S., Paciura, K., & Gerada, D. (2023) · IEEE Vehicle Power and Propulsion Conference (VPPC) · doi:10.1109/vppc60535.2023.10403273 · Cited by 2
Ant Colony Optimization- Tuned Fractional Order PID Controller for Speed Regulation In Hybrid Electric Vehicle
Nair, A. S. A. (2024) · International Conference on Recent Advances in Electrical, Electronics, Ubiquitous Communication, and Computational Intelligence (RAEEUCCI) · doi:10.1109/raeeucci61380.2024.10547797 · Cited by 2
Power electronics controlled electric propulsion systems
Bilhan, A. K., & Kabalcı, E. (2024) · Elsevier eBooks · doi:10.1016/b978-0-323-99545-0.00019-1 · Cited by 2
Expansion of Switched Reluctance Motor Driving Range by Flux-weakening Control under Current Vector Control
Kawarazaki, K., & Hoshi, N. (2024) · International Conference on Renewable Energy Research and Applications (ICRERA) · doi:10.1109/icrera62673.2024.10815351 · Cited by 2
Comprehensive Review on Hybrid Radial-Axial Flux Permanent Magnet Synchronous Motors
Madboly, M., & Ibrahim, M. H. (2024) · International Middle East Power Systems Conference (MEPCON) · doi:10.1109/mepcon63025.2024.10850104 · Cited by 2
Review on Enhancing Electric Vehicle Performance and Sustainability through Advanced Motor Technology and Thermal Management
Sundaramoorthy, P., Reddy, G. R., Kumar, A. P., Kumar, I. K., Tej, B. V., & Vijayakumar, A. (2025) · IEEE International Students' Conference on Electrical, Electronics and Computer Science (SCEECS) · doi:10.1109/sceecs64059.2025.10941493 · Cited by 2
Fuzzy Sliding Mode Control for logitudinal motion of underground mining electric vehicles
Ye, W., Shen, W., Zheng, J., Honnery, D., & Dayawansa, D. P. (2015) · IEEE Conference on Industrial Electronics and Applications (ICIEA) · doi:10.1109/iciea.2015.7334332 · Cited by 2
HEMIS Project (Electrical Powertrain HEalth Monitoring for Increased Safety of FEVs): Limitations of Electromagnetic Standards for Vehicles Equipped with Electrical Powertrain
Ruddle, A. R., Armstrong, R., & Galarza, A. (2015) · Lecture notes in mobility · doi:10.1007/978-3-319-13656-1_7 · Cited by 2
Multi-rate predictive cascade speed control of synchronous machines in automotive electrical traction drives
Carpiuc, S., & Lazǎr, C. (2015) · Mediterranean Conference on Control and Automation (MED) · doi:10.1109/med.2015.7158775 · Cited by 2
Low-Complexity Model Predictive Control of a Permanent Magnet Synchronous Machine System
Carpiuc, S., & Lazǎr, C. (2013) · International Conference on Control Systems and Computer Science · doi:10.1109/cscs.2013.51 · Cited by 2
Constrained state-feedback control of an externally excited synchronous machine
Carpiuc, S., & Lazar, M. (2013) · Mediterranean Conference on Control and Automation (MED) · doi:10.1109/med.2013.6608863 · Cited by 2
A new topology for fuel cell power trains including a new integrated converter
Neuburger, M., & Thrimawithana, D. J. (2015) · IEEE Brazilian Power Electronics Conference and Southern Power Electronics Conference · doi:10.1109/cobep.2015.7420097 · Cited by 2
Influence of driving cycles on traction motor design optimizations for electric vehicles
Chen, L., Wang, J., & Lazari, P. (2014) · Transport Research Arena (TRA) 5th Conference: Transport Solutions from Research to DeploymentEuropean CommissionConference of European Directors of Roads (CEDR)European Road Transport Research Advisory Council (ERTRAC)WATERBORNEᵀᴾEuropean Rail Research Advisory Council (ERRAC)Institut Francais des Sciences et Technologies des Transports, de l'Aménagement et des Réseaux (IFSTTAR)Ministère de l'Écologie, du Développement Durable et de l'Énergie · Cited by 2
A clustering based approach for energy efficient routing
Kosmides, P., Lambrinos, L., Asthenopoulos, V., Demestichas, K. P., & Adamopoulou, E. F. (2016) · IEEE Symposium on Computers and Communications (ISCC) · doi:10.1109/iscc.2016.7543745 · Cited by 2
Fuzzy parameter tuning sliding mode control for longitudinal motion of underground mining electric vehicles based on a single wheel model
Ye, W., Shen, W., Zheng, J., Honnery, D., & Dayawansa, D. P. (2016) · International Conference on Advanced Mechatronic Systems · doi:10.1109/icamechs.2016.7813461 · Cited by 2
Mechanical arrangements onboard ship of innovative permanent magnet linear actuators for steering gear
Bruzzese, C., Ruggeri, E., Rafiei, M., Zito, D., Santini, E., Mazzuca, T., & Lipardi, G. (2017) · International Symposium on Power Electronics (Ee) · doi:10.1109/pee.2017.8171675 · Cited by 2
Development of Singly Fed Mechanical-Offset Machine for Torque Ripple Minimization
Lee, C. H. T. (2018) · Springer theses · doi:10.1007/978-981-10-7077-8_5 · Cited by 2
Hafif Elektrikli Araçlar için Asenkron Motor Tasarımı ve Uygulaması
Ocak, C., & Yenipınar, B. (2021) · European Journal of Science and Technology · doi:10.31590/ejosat.949092 · Cited by 2
Development of an Automated Measurement Platform for an Electrical Traction System Test Bench
Houre, A. E., Yousfi, D., Bourzouk, Z., & Chaker, M. (2021) · Lecture notes in networks and systems · doi:10.1007/978-3-030-73882-2_163 · Cited by 2
Etat de l'art des topologies de machines électriques utilisées dans les véhicules électriques et hybrides
Cisse, K. M., Hlioui, S., Cheng, Y., & Belhadi, M. (2018) · HAL · Cited by 2
Performance improvement of 36‐slot 6‐terminal induction motor drive using pole phase modulation with higher slot per pole per phase
Umredkar, S. V., Keshri, R. K., Borghate, V. B., & Renge, M. M. (2023) · International Journal of Circuit Theory and Applications · doi:10.1002/cta.3662 · Cited by 2
Comparative study of electric motors in commercial EV applications
Subramaniam, S., Ramar, D., Thurai, P. V. R. T., & Prabhakaran, V. (2023) · AIP conference proceedings · doi:10.1063/5.0163921 · Cited by 2
SRM drive for electric vehicles with solar PV-powered and hysteresis current controller based minimization of torque ripple
Balasubramaniam, K. (2024) · AIP conference proceedings · doi:10.1063/5.0194885 · Cited by 2
An Investigative Study on the Development Strategies for Electric Vehicle Enterprises
Shah, S. R., & Zhang, L. (2024) · Engineering World · doi:10.37394/232025.2024.6.7 · Cited by 2
Methods for Determining Losses and Parameters of Cylindrical-Rotor Medium-Power Synchronous Generators
Komęza, K., & Dems, M. (2024) · Electronics · doi:10.3390/electronics13142766 · Cited by 2
A comprehensive study of electric propulsion system for vehicular application
Kumar, L., & Jain, S. (2014) · Journal of Renewable and Sustainable Energy · doi:10.1063/1.4861781 · Cited by 2
A Power Buffer in an Electric Driveline: Two Batteries Are Better Than One
de Santiago, J., Burmeister, F., Lundin, J., & Oliveira, J. G. (2014) · ISRN Automotive Engineering · doi:10.1155/2014/525630 · Cited by 2
Outer Rotor SRM Design for Electric Vehicle without Reducer via Speed-Up Evolutionary Algorithm
Omaç, Z., Polat, M., Kaya, M., Öksüztepe, E., Eren, H., Yıldırım, M., & Kürüm, H. (2019) · IntechOpen eBooks · doi:10.5772/intechopen.74451 · Cited by 2
Design and Optimization of Synchronous Motors for Low-Voltage Electric Vehicles
Babetto, C., Berardi, G., Bianchi, N., & Benedetti, G. (2019) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce.2019.8912670 · Cited by 2
Modeling and Identification of an Electric Vehicle Braking System: Thermal and Tribology Phenomena Assessment
D’hondt, T., Forrier, B., Sarrazin, M., Favilli, T., Pugi, L., Berzi, L., Viviani, R., & Pierini, M. (2020) · SAE technical papers on CD-ROM/SAE technical paper series · doi:10.4271/2020-01-1094 · Cited by 2
Overload Performance Prediction of PM and Synchronous Reluctance Machines for Traction Applications
Carbonieri, M., Soong, W. L., Mahmoudi, A., Kahourzade, S., & Bianchi, N. (2020) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce44975.2020.9235921 · Cited by 2
Analytical and Experimental Investigations of Radial Force Detection by Strain Gauge for Possible Application for Switched Reluctance Machines
Cai, Y., Wiguna, C. A., Sugimoto, H., & Chibá, A. (2020) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce44975.2020.9235801 · Cited by 2
Design of a Power Electronic Drive for a Small Utility Electric Vehicle
Mathew, A. R., Bindu, R., & Thale, S. (2020) · IEEE India Council International Subsections Conference (INDISCON) · doi:10.1109/indiscon50162.2020.00027 · Cited by 2
A Five-Level Boost NPC Inverter for Electric Vehicle
Sarkar, K., Chakrabarti, A., & Biswas, S. K. (2020) · IEEE International Conference on Power Electronics, Drives and Energy Systems · doi:10.1109/pedes49360.2020.9379599 · Cited by 2
Design of a direct current motor with a windingless rotor for electric vehicles
Ivliev, D., Kosenkov, V., Vynakov, O., Savolova, E. V., & Yarmolovych, V. (2021) · Eastern-European Journal of Enterprise Technologies · doi:10.15587/1729-4061.2021.231733 · Cited by 2
Análise de impactos técnicos provocados pela penetração massiva de veículos elétricos em redes de distribuição de energia elétrica
Arioli, V. T. (2016) · doi:10.47749/t/unicamp.2016.973078 · Cited by 2
NOVEL METHODS FOR PERMANENT MAGNET DEMAGNETIZATION DETECTION IN PERMANENT MAGNET SYNCHRONOUS MACHINES
Zhu, M. (2018) · Scholarship at UWindsor (University of Windsor) · Cited by 2
Sliding Mode Speed Estimation of Induction Motor with MPC Based Flux Weakening Control for Electric Vehicle
Çavuş, B., & Aktaş, M. (2024) · Afyon Kocatepe University Journal of Sciences and Engineering · doi:10.35414/akufemubid.1472301 · Cited by 1
An Energy Resource Management for Cluster based IoHV Supported by Fog Computing
Kadhim, A. J. (2024) · Karbala International Journal of Modern Science · doi:10.33640/2405-609x.3387 · Cited by 1
Kinetic Energy Recovery: Assessment on the impact of Permanent Magnet Synchronous Motor and Battery Dynamic models
Lombardi, S., Federici, L., Tribioli, L., & Bella, G. (2025) · SAE International Journal of Advances and Current Practices in Mobility · doi:10.4271/2025-01-0303 · Cited by 1

Authors: de Santiago, J., Bernhoff, H., Ekergård, B., Eriksson, S., Ferhatovic, S., Waters, R., & Leijon, M.
Affiliations: Uppsala University (SE)
ORCID: de Santiago, Juan
Bernhoff, Hans
Eriksson, Sandra
Leijon, Mats
Venue: IEEE Transactions on Vehicular Technology
Publisher: Institute of Electrical and Electronics Engineers (IEEE)
Published: 2012-02
Volume: 61
Issue: 2
Pages: 475-484
ISSN: 0018-9545 (ISSN-L)
1939-9359
DOI: 10.1109/tvt.2011.2177873
OpenAlex: W1966845491
Cited by: 669
References: 87
Citations by year: 2026: 22 · 2025: 38 · 2024: 49 · 2023: 58 · 2022: 57 · 2021: 69 · 2020: 93 · 2019: 52 · 2018: 34 · 2017: 38 · 2016: 54 · 2015: 31 · 2014: 45 · 2013: 20 · 2012: 9
FWCI: 16.58
Type: journal article
Language: en
Open access: green
urn.kb.se
Licence: other-oa
ieeexplore.ieee.org/Xplorehelp/downloads/license-information/IEEE.html (vor)
doi.org/10.15223/policy-029 (stm-asf)
doi.org/10.15223/policy-037 (stm-asf)
Locations: IEEE Transactions on Vehicular Technology (publishedVersion)
KTH Publication Database DiVA (KTH Royal Institute of Technology) (submittedVersion, other-oa)
Funders: VINNOVA
Stiftelsen Olle Engkvist Byggmästare
Vetenskapsrådet (621-2009-3417)
Energimyndigheten (621-2009-3417)
Topics: Physical Sciences › Engineering › Electrical and Electronic Engineering › Electric Motor Design and Analysis
Physical Sciences › Engineering › Automotive Engineering › Electric and Hybrid Vehicle Technologies
Physical Sciences › Engineering › Electrical and Electronic Engineering › Sensorless Control of Electric Motors
Keywords: all-electric vehicles, induction motor, permanent magnet motor, electric commercial vehicles, motor comparison, motor testing

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

Electrical Motor Drivelines in Commercial All-Electric Vehicles: A Review

Abstract

Overview

Integrity signals

Verification

Claims the paper makes

Claims other papers make about this one

Citations

Cites

Cited by

Related

Metadata

Record

About these checks