CoChat

Elastocapillary self-assembled neurotassels for stable neural activity recordings

Open access

The DOI matches its Crossref record; 61 of the 61 references it cites were found in a registry or an index.

Abstract

Neurotassels self-assemble into thin fibers through elastocapillary interactions and enable stable neural activity recordings.

Overview

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Integrity signals

Registry

Crossref · 10.1126/sciadv.aav2842

Cites

61 of 61 references verified0 citation errors · 0 not checkable

Statistics

Figures

Fig. 1 Elastocapillary self-assembly of Neurotassels. (A) An as-fabricated 16-channel Neurotassel. The black dashed box highlights the freestanding segment supported on an aluminum release layer. XT and XL are the transverse and longitudinal directions, respectively. Scale bar, 500 μm. (B) Zoom-in view of 12-μm-wide and 3-μm-high microelectrode filaments, as marked by the dashed red box in (A). Scale bar, 50 μm. Inset: Scanning electron microscopy (SEM) image of a microelectrode filament with a 10-μm-diameter recording site. Scale bar, 10 μm (inset). (C) Simulated von Mises stresses in a deformed Neurotassel. (D) Schematics of the elastocapillary self-assembly of a Neurotassel. (E) Time sequence photographs of the elastocapillary self-assembly of a Neurotassel. Scale bar, 1 mm. (Photo credit: Shouliang Guan and Jinfen Wang at NCNST). (F) A Neurotassel/PEG assembly. Scale bar, 500 μm. (G and H) Zoom-in views of the Neurotassel/PEG assembly as marked by the red and black dashed boxes, respectively, in (F). Scale bars, 100 μm. (I) Cross-sectional image at the mesh-filament transition section, indicated by the red arrows in (G). Scale bar, 50 μm. (J) Cross-sectional image of the fiber. Scale bar, 10 μm.
Fig. 1 Elastocapillary self-assembly of Neurotassels. (A) An as-fabricated 16-channel Neurotassel. The black dashed box highlights the freestanding segment supported on an aluminum release layer. XT and XL are the transverse and longitudinal directions, respectively. Scale bar, 500 μm. (B) Zoom-in view of 12-μm-wide and 3-μm-high microelectrode filaments, as marked by the dashed red box in (A). Scale bar, 50 μm. Inset: Scanning electron microscopy (SEM) image of a microelectrode filament with a 10-μm-diameter recording site. Scale bar, 10 μm (inset). (C) Simulated von Mises stresses in a deformed Neurotassel. (D) Schematics of the elastocapillary self-assembly of a Neurotassel. (E) Time sequence photographs of the elastocapillary self-assembly of a Neurotassel. Scale bar, 1 mm. (Photo credit: Shouliang Guan and Jinfen Wang at NCNST). (F) A Neurotassel/PEG assembly. Scale bar, 500 μm. (G and H) Zoom-in views of the Neurotassel/PEG assembly as marked by the red and black dashed boxes, respectively, in (F). Scale bars, 100 μm. (I) Cross-sectional image at the mesh-filament transition section, indicated by the red arrows in (G). Scale bar, 50 μm. (J) Cross-sectional image of the fiber. Scale bar, 10 μm.CC BY-NC · PubMed Central
Fig. 2 Recordings by Neurotassels during DPA tasks. (A) Schematic of the olfactory DPA task. (B) Performance of mice trained with the DPA task. Insets: An implanted 16-channel Neurotassel (left) and a mouse with an implanted Neurotassel in the mPFC (right). Error bars represent SD around the mean (n = 6). Scale bar, 1 mm (inset). (Photo credit: Xiaowei Gu at ION). (C) Microphoto of a 200-μm-thick brain slice with an implanted Neurotassel. The mouse brain was sliced in sagittal direction and parallel to the implanted Neurotassel. Anatomical borders were identified according to the stereotaxic atlas of Paxinos and Watson (2001). Scale bar, 500 μm. (D) Extracellular AP traces (250 to 8000 Hz) recorded by a 16-channel Neurotassel implanted in the mPFC of M04. Scale bars, 200 μV (vertical), 100 ms (horizontal). (E) LFP traces (0.5 to 200 Hz) during a task trial. Scale bars, 300 μV (vertical), 1 s (horizontal). (F) Spike rasters of isolated neurons during a task trial. Scale bars, 50 μV (vertical), 1 s and 1 ms (horizontal; left and right, respectively).
Fig. 2 Recordings by Neurotassels during DPA tasks. (A) Schematic of the olfactory DPA task. (B) Performance of mice trained with the DPA task. Insets: An implanted 16-channel Neurotassel (left) and a mouse with an implanted Neurotassel in the mPFC (right). Error bars represent SD around the mean (n = 6). Scale bar, 1 mm (inset). (Photo credit: Xiaowei Gu at ION). (C) Microphoto of a 200-μm-thick brain slice with an implanted Neurotassel. The mouse brain was sliced in sagittal direction and parallel to the implanted Neurotassel. Anatomical borders were identified according to the stereotaxic atlas of Paxinos and Watson (2001). Scale bar, 500 μm. (D) Extracellular AP traces (250 to 8000 Hz) recorded by a 16-channel Neurotassel implanted in the mPFC of M04. Scale bars, 200 μV (vertical), 100 ms (horizontal). (E) LFP traces (0.5 to 200 Hz) during a task trial. Scale bars, 300 μV (vertical), 1 s (horizontal). (F) Spike rasters of isolated neurons during a task trial. Scale bars, 50 μV (vertical), 1 s and 1 ms (horizontal; left and right, respectively).CC BY-NC · PubMed Central
Fig. 3 Recording stability during DPA tasks. (A) Heat map of normalized firing rates (FRs) for the recorded neurons by Neurotassels during training. Each row represents the baseline-normalized firing rate of one neuron. The dashed red lines represent the onsets and offsets of odor delivery. (B) Distribution of neurons according to the continuously recorded duration days by Neurotassels (left) and microwire tetrodes (right), respectively. One hundred twenty-one (121) neurons were recorded by six Neurotassels from six mice, and 730 neurons were recorded by 256 tetrodes from eight mice. Each tetrode was constructed by twisting four PI-insulated, Ni-Chrome wires with a 12.5-μm-diameter core. (C) Cumulative distribution of the percentage of neurons as a function of recording duration showing significant increases in recording of Neurotassels (red line) compared with that of tetrodes (black line) (**P < 0.01, Kolmogorov-Smirnov test). (D) The waveforms of an example neuron stably recorded during the training process. Scale bars, 50 μV (vertical), 0.5 ms (horizontal). (E) Heat map of the normalized firing rate for two example neurons. Each row represents the baseline-normalized firing rate of one training day. (F) Percentage of neurons with an increase or a decrease in firing through training during the delay (left) and response (right) periods, respectively. Twenty-six (26) neurons that were continuously recorded for longer than 5 days were considered here.
Fig. 3 Recording stability during DPA tasks. (A) Heat map of normalized firing rates (FRs) for the recorded neurons by Neurotassels during training. Each row represents the baseline-normalized firing rate of one neuron. The dashed red lines represent the onsets and offsets of odor delivery. (B) Distribution of neurons according to the continuously recorded duration days by Neurotassels (left) and microwire tetrodes (right), respectively. One hundred twenty-one (121) neurons were recorded by six Neurotassels from six mice, and 730 neurons were recorded by 256 tetrodes from eight mice. Each tetrode was constructed by twisting four PI-insulated, Ni-Chrome wires with a 12.5-μm-diameter core. (C) Cumulative distribution of the percentage of neurons as a function of recording duration showing significant increases in recording of Neurotassels (red line) compared with that of tetrodes (black line) (**P < 0.01, Kolmogorov-Smirnov test). (D) The waveforms of an example neuron stably recorded during the training process. Scale bars, 50 μV (vertical), 0.5 ms (horizontal). (E) Heat map of the normalized firing rate for two example neurons. Each row represents the baseline-normalized firing rate of one training day. (F) Percentage of neurons with an increase or a decrease in firing through training during the delay (left) and response (right) periods, respectively. Twenty-six (26) neurons that were continuously recorded for longer than 5 days were considered here.CC BY-NC · PubMed Central
Fig. 4 Simultaneous optogenetic stimulation and electrical recordings. (A) Schematic of elastocapillary self-assembly of a Neurotassel on a sharpened optical fiber. (B) A 61-channel Neurotassel assembled on a sharpened optical fiber without (left) and with (right) light, respectively. Scale bars, 100 μm. (C) Black: Potential trace for a single trial with optogenetic transients at onset and offset of laser stimulation. Orange: Potential trace after subtraction of the median. Scale bars, 0.1 mV (vertical), 10 ms (horizontal). (D) Average waveforms of light-evoked (blue) and spontaneous (black) spikes. Scale bars, 50 μV (vertical), 0.5 ms (horizontal). (E) Raster plots of evoked spike firing of an example neuron by 10-Hz (left) and 20-Hz (right) 5-ms laser stimulation (marked by blue bars). (F) Distribution of spike jitter from laser as measured by the delay from stimulation onset to the first evoked spikes during the 10-Hz (left, total 200 pulses) and 20-Hz (right, total 400 pulses) stimulation. (G) Top: Heat map of firing rates of seven neurons in response to 1-s laser stimulation. Middle: Averaged firing rate of the neurons. Bottom: Heat map of field potentials at the recording sites of the neurons.
Fig. 4 Simultaneous optogenetic stimulation and electrical recordings. (A) Schematic of elastocapillary self-assembly of a Neurotassel on a sharpened optical fiber. (B) A 61-channel Neurotassel assembled on a sharpened optical fiber without (left) and with (right) light, respectively. Scale bars, 100 μm. (C) Black: Potential trace for a single trial with optogenetic transients at onset and offset of laser stimulation. Orange: Potential trace after subtraction of the median. Scale bars, 0.1 mV (vertical), 10 ms (horizontal). (D) Average waveforms of light-evoked (blue) and spontaneous (black) spikes. Scale bars, 50 μV (vertical), 0.5 ms (horizontal). (E) Raster plots of evoked spike firing of an example neuron by 10-Hz (left) and 20-Hz (right) 5-ms laser stimulation (marked by blue bars). (F) Distribution of spike jitter from laser as measured by the delay from stimulation onset to the first evoked spikes during the 10-Hz (left, total 200 pulses) and 20-Hz (right, total 400 pulses) stimulation. (G) Top: Heat map of firing rates of seven neurons in response to 1-s laser stimulation. Middle: Averaged firing rate of the neurons. Bottom: Heat map of field potentials at the recording sites of the neurons.CC BY-NC · PubMed Central
Fig. 5 Chronic stability of implanted Neurotassels. (A to C) Average spike amplitude, SNR, and firing rate of all sortable neurons recorded by Neurotassels from 3 to 6 weeks after implantation. Error bars represent SD around the mean. (D) Aligned and average spike waveforms recorded by a microelectrode of a 16-channel Neurotassel from 3 to 6 weeks after implantation. Scale bars, 100 μV (vertical), 1 ms (horizontal). (E) PCA of all waveforms in (D). (F) Time evolution of ISI histograms. Bin size, 20 ms. (G to L) Immunohistochemical staining and bright-field images of a horizontal brain slice after 5-week implantation of a Neurotassel and a silicon probe, respectively. The 100-μm-thick slice was labeled for astrocytes [glial fibrillary acidic protein (GFAP), green] and neurons (NeuN, red). Inset: A silicon probe with a cross-section of 100 × 30 μm2. Scale bars, 50 μm (G to L), 100 μm (L, inset).
Fig. 5 Chronic stability of implanted Neurotassels. (A to C) Average spike amplitude, SNR, and firing rate of all sortable neurons recorded by Neurotassels from 3 to 6 weeks after implantation. Error bars represent SD around the mean. (D) Aligned and average spike waveforms recorded by a microelectrode of a 16-channel Neurotassel from 3 to 6 weeks after implantation. Scale bars, 100 μV (vertical), 1 ms (horizontal). (E) PCA of all waveforms in (D). (F) Time evolution of ISI histograms. Bin size, 20 ms. (G to L) Immunohistochemical staining and bright-field images of a horizontal brain slice after 5-week implantation of a Neurotassel and a silicon probe, respectively. The 100-μm-thick slice was labeled for astrocytes [glial fibrillary acidic protein (GFAP), green] and neurons (NeuN, red). Inset: A silicon probe with a cross-section of 100 × 30 μm2. Scale bars, 50 μm (G to L), 100 μm (L, inset).CC BY-NC · PubMed Central
Fig. 6 Scalability of Neurotassels. (A) An as-fabricated 128-channel Neurotassel. Scale bar, 1 mm. (B) Zoom-in view of the microelectrode filaments in the red dashed box in (A). Scale bar, 50 μm. Inset: Zoom-in view in the white dashed box. Scale bar, 10 μm (inset). (C) An as-fabricated 1024-channel Neurotassel. Scale bar, 1 mm. (D) Zoom-in view of the microelectrode filaments in the red dashed box in (C). Scale bar, 50 μm. Inset: Zoom-in view in the white dashed box. Scale bar, 10 μm (inset). (E) An SEM image (tilted at 45°) of Pt-coated microelectrode filaments of a released 1024-channel Neurotassel. Scale bar, 10 μm. Inset: Focused ion beam–polished cross-section along the red dashed line. Scale bar, 1 μm (inset). (F and G) Assembled 128- and 1024-channel Neurotassel/PEG composite fibers, respectively. Scale bars, 200 μm. (H and I) Cross-sectional images of the assembled 128- and 1024-channel Neurotassel/PEG composite fibers, respectively. Scale bars, 20 μm. (J) Averaged impedance and yield of 16-, 61-, 128-, 256-, 512-, and 1024-channel Neurotassels after Pt electrodeposition. Error bars represent SE (n = 20).
Fig. 6 Scalability of Neurotassels. (A) An as-fabricated 128-channel Neurotassel. Scale bar, 1 mm. (B) Zoom-in view of the microelectrode filaments in the red dashed box in (A). Scale bar, 50 μm. Inset: Zoom-in view in the white dashed box. Scale bar, 10 μm (inset). (C) An as-fabricated 1024-channel Neurotassel. Scale bar, 1 mm. (D) Zoom-in view of the microelectrode filaments in the red dashed box in (C). Scale bar, 50 μm. Inset: Zoom-in view in the white dashed box. Scale bar, 10 μm (inset). (E) An SEM image (tilted at 45°) of Pt-coated microelectrode filaments of a released 1024-channel Neurotassel. Scale bar, 10 μm. Inset: Focused ion beam–polished cross-section along the red dashed line. Scale bar, 1 μm (inset). (F and G) Assembled 128- and 1024-channel Neurotassel/PEG composite fibers, respectively. Scale bars, 200 μm. (H and I) Cross-sectional images of the assembled 128- and 1024-channel Neurotassel/PEG composite fibers, respectively. Scale bars, 20 μm. (J) Averaged impedance and yield of 16-, 61-, 128-, 256-, 512-, and 1024-channel Neurotassels after Pt electrodeposition. Error bars represent SE (n = 20).CC BY-NC · PubMed Central

Verification

Claims the paper makes

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Claims other papers make about this one

Each is checked against this paper’s own text: does it say what the citing paper says it does?

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

The self-check needs the paper’s full text.

Citations

Cites

Cited by

See all 222

Metadata

Authors
Guan, S., Wang, J., Gu, X., Zhao, Y., Hou, R., Fan, H., Zou, L., Gao, L., Du, M., Li, C., & Fang, Y.
Affiliations
  • Chinese Academy of Sciences (CN)
  • Hunan University (CN)
  • National Center for Nanoscience and Technology (CN)
Corresponding author
  • Guan, S.
  • Wang, J.
  • Gu, X.
  • Li, C.
  • Fang, Y.
Venue
Science Advances
Published
2019-03
Volume
5
Issue
3
Pages
eaav2842-eaav2842
ISSN
2375-2548 (ISSN-L)
OpenAlex
W2922865870
Cited by
222
References
60
Citations by year
2026: 20 · 2025: 36 · 2024: 33 · 2023: 37 · 2022: 33 · 2021: 31 · 2020: 25 · 2019: 7
FWCI
11.47
Type
journal article
Language
en
Open access
Licence
cc-by-nc
Locations
  • Science Advances (publishedVersion, cc-by-nc)
  • Europe PMC (PubMed Central) (publishedVersion, cc-by-nc)
  • PubMed Central (publishedVersion, cc-by-nc)
  • PubMed (publishedVersion)
Funders
  • National Natural Science Foundation of China (21790393, 21673057, 31525010)
  • CAS Key Research Program of Frontier Sciences (QYZDB-SSW-SMC009)
  • CAS Instrument Developing Project (YZ201540)
Topics
  • Life Sciences › Neuroscience › Cellular and Molecular Neuroscience › Neuroscience and Neural Engineering
  • Physical Sciences › Engineering › Biomedical Engineering › Advanced Sensor and Energy Harvesting Materials
  • Social Sciences › Education › Undergraduate Neuroscience Education and Research
Keywords
neural recording, neural interfaces, neuroprosthetics, flexible electronics
MeSH terms
Action Potentials, Animals, Brain, Capillaries, Elasticity, Electrodes, Implanted, Humans, Intermediate Filaments, Male, Mice, Inbred C57BL, Microelectrodes, Nerve Net, Neurons, Neurophysiology, Neurites, Electrophysiological Phenomena

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.