The DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index; 2 of the 20 sources its claims cite were checked for support.
A General Energy Balance for Battery Systems
Open accessAbstract
A general energy balance for battery systems has been developed. This equation is useful for estimating cell thermal characteristics. Reliable predictions of cell temperature and heat‐generation rate are required for the design and thermal management of battery systems. The temperature of a cell changes as a result of electrochemical reactions, phase changes, mixing effects, and joule heating. The equation developed incorporates these effects in a complete and general manner. Simplifications and special cases are discussed. The results of applying the energy balance to a mathematical model of the cell discharged through two different reaction mechanisms are given as examples. The examples illustrate how the energy equation may be applied to a specific system to examine the relative contributions corresponding to the terms in the equation. The examples show that the processes involved in cell heat generation may be complex and that the application of a sufficiently general energy equation is advantageous.
Overview
CoChat Summary
TL;DR
The paper derives a general energy balance for battery systems that includes mixing, phase changes, and simultaneous electrochemical reactions with composition-dependent open-circuit potentials. It applies the equation to a modeled LiAl/LiCl-KCl/FeS cell discharged by two mechanisms and to a lead-acid estimate, showing that cell heat generation can be complex and that a sufficiently general energy equation is advantageous.
Key findings
- A general energy balance is developed that includes energy contributions from mixing, phase changes, and simultaneous electrochemical reactions with composition-dependent open-circuit potentials; prior treatments were restricted to single pure-phase reactants or a single reaction without mixing effects.
- For the LiAl/FeS model, adiabatic-reversible discharge gives the same temperature at 100% depth of discharge for both mechanisms because the overall reaction is the same; slope discontinuities occur at 50% and 12% utilization for mechanisms 1 and 2, respectively. In the realistic simulations, the second reaction begins at 30% and 11% utilization for mechanisms 1 and 2, respectively.
- The mixing term is negligible in the LiAl/FeS example; at 25% utilization, the temperature decline after current interruption is only about 0.2 K. For a lead-acid cell, the estimated temperature rise after full discharge is approximately 1.6 K, or 2.9 K if 1.25 mol of PbO2 is allowed for discharge.
- The sign of the mixing effect depends on the enthalpy curve: for lead-acid, the sulfuric acid-water enthalpy curve is concave upward, so a well-insulated cell heats after current interruption; for the high-temperature LiCl-KCl cell, the curve is concave downward, so the cell cools after interruption. Neglecting mixing overestimates lead-acid operating temperature and underestimates high-temperature cell operating temperature.
Methods
- The paper derives the energy balance from the first law of thermodynamics, assuming uniform battery temperature, and presents a final general equation including reaction, heat-capacity, phase-change, mixing, electrical-work, and heat-transfer terms.
- The equation is applied to an existing one-dimensional mathematical model of the LiAl/LiCl-KCl/FeS cell with a porous LiAl negative electrode, porous FeS positive electrode, electrolyte reservoir, and separator under galvanostatic discharge, using the two reaction mechanisms in Table I.
- Appendix A estimates the lead-acid temperature rise using an assumed uniform 5 molal sulfuric acid electrolyte, with one-third of the electrolyte in the cathode and anode spaces and one-third between the electrodes; the analysis compares adiabatic-reversible profiles with model simulations and examines the relative contributions of terms.
Limitations
- The paper states that the rigorous energy balance is difficult to apply without a detailed mathematical model because instantaneous composition profiles and current fractions are required; in practice, obtaining concentration profiles and predicting current partitioning among possible reactions is difficult.
- The paper states that the analysis does not include enthalpy changes from nonfaradaic reactions; self-discharge or corrosion must be divided into anodic and cathodic components and included as an additional term. The mixing term is also difficult because it involves integrations of concentration profiles.
- The paper states that actual FeS discharge is complicated and more like a mixture of the two proposed mechanisms plus simultaneously occurring chemical reactions; the examples are model simulations. The lead-acid estimate assumes artificial concentration jumps at interfaces, and diffusion would lower the estimate; nonuniform reaction distribution in porous electrodes would make the concentration distribution nonuniform. The breakdown is presented only up to 30% utilization because oscillatory behavior begins when the second reaction starts, to be treated in a subsequent publication.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
0 Valid · 5 Not valid · 12 Not checked · 75 Own results and interpretations
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“Basing the discharge on two Farādays (1 mol PbOg) and a transference number of 0.74 for hydrogen ion, we may calculate that the concentration in the cathode space and anode space drops to 1.04 and 2.79 molal, respectively (14).”
What the sources say
- Could not verifycites [14] 14. Hans Bode, "Lead-Acid Batteries," R. J. Brodd and K. V. Kordesch, Translators, Wiley-Interscience, New York (1977). sourceExperimental — accuracy not yet measured
The available text in the book-review passage (section labeled “Notice to Members April 1 is Cut-Off Date”; page not provided) describes the book’s theoretical treatment of lead-acid batteries but does not give this calculation. Searches for the 0.74 hydrogen-ion transference number, two Faradays, and the 1.04 and 2.79 molal concentrations found no passage addressing the claimed values. (LLM, conf=0.76)
hedgedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on 5 assumptions not shown here.
- Could not verify
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“The temperature rise, after full discharge, is approximately 1.6 K.”
- Also stated in: § Estimate of the Temperature Rise in a Lead-Acid Cell Following Current Interruption · p. 8 · hedged
“Using the data available in Ref. (14) (for 298 K), we calculate the temperature rise to be about 1.6 K”
What the sources say
- Could not verifycites [14] 14. Hans Bode, "Lead-Acid Batteries," R. J. Brodd and K. V. Kordesch, Translators, Wiley-Interscience, New York (1977). sourceExperimental — accuracy not yet measured
The available passages from the book review (page not provided) describe the book’s coverage of lead-acid battery thermodynamics but give no temperature rise after full discharge. Searches for “1.6 K” and the discharge-temperature claim found no supporting passage in our copy. (LLM, conf=0.75)
hedged- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on 5 assumptions not shown here.
- Also stated in: § Estimate of the Temperature Rise in a Lead-Acid Cell Following Current Interruption · p. 8 · hedged
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Although the mixing term offers a negligible contribution to the energy balance, it is interesting to investigate the processes that determine its behavior.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The profile for the X-phase mechanism in Fig. 1 follows the adiabatic-reversible profile up to about 5% utilization because the heat-loss contribution tends to cancel the polarization heat.”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“A general energy balance for battery systems has been developed.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on 3 assumptions not shown here.
39 more claims
Create a free account to see all 92 claims and every source verdict.
- It may state two separate claims as one. 20
- Probably not a substantial claim. 33
- The quote only partly states this claim. 1
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Conclusions · p. 8
“Equation [23], written for a single cell reaction, is the energy equation most commonly used in battery applications.”
§ Discussion of Terms · p. 5
“Furthermore, Eq. [24] is the form of the energy balance that is most commonly encountered in the literature.”
Citations
Cites
The publisher hasn’t deposited this paper’s reference list.
Research works printed but not linked: 12
- [1]1. J. M. Sherfey and A. Brenner, This Journal, 105, 665 (1958).
- [3]3. H. F. Gibbard, This Journal, 125, 353 (1978).
- [2]2. S. Gross, Energy Convers., 9, 55 (1969).
- [4]4. I. A. Dibrov and V. A. Bykov, Sov. Electrochem., 13, 298 (1977).
- [6]6. L. D. Hansen and R. M. Hart, This Journal, 125, 842 (1978).
- [5]5. I. A. Dibrov and V. A. Bykov, J. Appl. Chem., 49, 2025 (1977).
- [7]7. F. B. Tudron, ibid., 128, 516 (1981).
- [9]9. W. H. Tiedemann and J. Newman, in "Battery Design and Optimization," S. Gross, Editor, pp. 23-38, The Electrochemical Society Softbound Proceedings Series, Princeton, NJ (1979).
- [8]8. D. M. Chen and H. F. Gibbard, ibid., 130, 1975 (1983).
- [10]10. Richard Pollard and John Newman, This Journal, 128, 491 (1981).
- [11]11. Richard Pollard and John Newman, ibid., 128, 502 (1981).
- [13]13. Z. Tomczuk, S. K. Preto, and M. F. Roche, This Journal, 128, 760 (1981).
Cited by
Items 1,101–1,200 of 2,542
Analysis of Heat-Spreading Thermal Management Solutions for Lithium-Ion Batteries
Khasawneh, H. J., Neal, J. A., Canova, M., GUEZENNEC, Y. G., Wayne, R., Taylor, J., Smalc, M., & Norley, J. (2011) · Volume 4: Energy Systems Analysis, Thermodynamics and Sustainability; Combustion Science and Engineering; Nanoengineering for Energy, Parts A and B · doi:10.1115/imece2011-63662 · Cited by 16
Multiphysical field measurement and fusion for battery electric-thermal-contour performance analysis
Li, X., Zhang, Z., Wang, W., Tian, Y., Li, D., & Tian, J. (2020) · Applied Energy · doi:10.1016/j.apenergy.2020.114518 · Cited by 16
A thermal‐structure coupled optimization study of lithium‐ion battery modules with mist cooling
Qian, L. (2020) · International Journal of Energy Research · doi:10.1002/er.5220 · Cited by 17
Kang, T., Lee, P., Kwon, S., Yoo, K., & Kim, J. (2021) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2021.116936 · Cited by 16
Ziat, K., Louahlia, H., Petrone, R., et al. (2021) · International Journal of Energy Research · doi:10.1002/er.6923 · Cited by 16
Development of a one-dimensional thermal-electrochemical model of lithium ion battery
Wang, T., Tseng, K. J., Yin, S., et al. (2013) · Proceedings of the Annual Conference of the IEEE Industrial Electronics Society · doi:10.1109/iecon.2013.6700243 · Cited by 16
Verbrugge, M. W. (1995) · Journal of Electrostatics · doi:10.1016/0304-3886(94)00042-u · Cited by 16
Fuller, T. F., & Newman, J. S. (1995) · Modern aspects of electrochemistry · doi:10.1007/978-1-4899-1724-9_4 · Cited by 16
Self-citationModeling and Simulation of Battery Systems
Mukherjee, P. P., Pannala, S., & Turner, J. (2011) · Wiley eBooks · doi:10.1002/9783527637188.ch25 · Cited by 22
Murphy, M., & Akrami, M. (2024) · Batteries · doi:10.3390/batteries10080264 · Cited by 18
Torrano, I., Martín-Ortiz, J., Herrán, A., Dauvergne, J., & Bielsa, D. (2024) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2024.126247 · Cited by 16
Sutheesh, P. M., Thomas, R., & Bandaru, R. (2025) · International Communications in Heat and Mass Transfer · doi:10.1016/j.icheatmasstransfer.2025.108992 · Cited by 15
Yu, L., Zhang, A., Pang, D., & Wang, B. (2025) · Case Studies in Thermal Engineering · doi:10.1016/j.csite.2025.106315 · Cited by 15
Teker, E., & Gökaslan, M. Y. (2025) · International Communications in Heat and Mass Transfer · doi:10.1016/j.icheatmasstransfer.2025.109431 · Cited by 15
Dong, W., Shen, J., Xu, Y., Wu, Z., Xu, X., Long, Y., Wang, X., & Zhou, F. (2025) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2025.128455 · Cited by 16
Sok, R., & Kusaka, J. (2025) · eTransportation · doi:10.1016/j.etran.2025.100499 · Cited by 19
Fan, Y., Wang, Z., Yang, H., et al. (2025) · Energy · doi:10.1016/j.energy.2025.139404 · Cited by 15
Droese, D., & Kowal, J. (2023) · Applied Sciences · doi:10.3390/app13052870 · Cited by 15
Zhang, Y., Zhao, S., Zhou, T., Wang, H., Li, S., Yuan, Y., Ma, Z., Wei, J., & Zhao, X. (2023) · Batteries · doi:10.3390/batteries9030153 · Cited by 19
Lechermann, L., Kleiner, J., Komsiyska, L., Hinterberger, M., & Endisch, C. (2023) · Journal of Energy Storage · doi:10.1016/j.est.2023.107188 · Cited by 14
Algorithm-driven optimization of lithium-ion battery thermal modeling
Sun, Z., Guo, Y., Zhang, C., et al. (2023) · Journal of Energy Storage · doi:10.1016/j.est.2023.107388 · Cited by 15
Jiang, Z., Yang, Y., & Qiu, H. (2023) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2023.120869 · Cited by 16
Wang, H., Wang, C., Jiang, C., et al. (2023) · Journal of Energy Storage · doi:10.1016/j.est.2023.108125 · Cited by 15
Kılıç, M., Gamsız, S., & Alınca, Z. N. (2023) · Sustainability · doi:10.3390/su151612391 · Cited by 15
Bose, B., Shaosen, S., Li, W., Gao, L., Wei, K., & Garg, A. (2023) · Sustainable Energy Grids and Networks · doi:10.1016/j.segan.2023.101197 · Cited by 20
Du, X., Park, J., Choe, S.-Y., Garrick, T. R., Dix, S. T., & Zhang, H. (2024) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/ad4ac6 · Cited by 14
Design of CTP liquid cooling battery pack and thermal Characterization experiments
Hongsong, Z., Wang, S., Deng, H., Liu, S., Wang, J., & Ren, S. (2024) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2024.124196 · Cited by 15
Liu, Z., Ji, S., Wang, B., et al. (2024) · International Communications in Heat and Mass Transfer · doi:10.1016/j.icheatmasstransfer.2024.108304 · Cited by 15
Zhao, W., Meng, C., Zhao, Y., et al. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.115675 · Cited by 15
Skoog, S. (2017) · IEEE Applied Power Electronics Conference and Exposition (APEC) · doi:10.1109/apec.2017.7931031 · Cited by 15
Prediction of temperature behavior of a lead–acid battery by means of Lewis number
Nazghelichi, T., Torabi, F., & Esfahanian, V. (2018) · Electrochimica Acta · doi:10.1016/j.electacta.2018.04.092 · Cited by 15
Inui, Y., Hirayama, S., & Tanaka, T. (2019) · Electronics and Communications in Japan · doi:10.1002/ecj.12221 · Cited by 15
Compactness analysis of PCM-based cooling systems for lithium battery-operated vehicles
Rangappa, R., Rajoo, S., Samin, P. M., et al. (2020) · International journal of energy and environmental engineering · doi:10.1007/s40095-020-00339-z · Cited by 15
Garg, A., Liu, C., Jishnu, A. K., et al. (2020) · Journal of Electrochemical Energy Conversion and Storage · doi:10.1115/1.4048537 · Cited by 15
An Electro-Thermal Model for LFP Cells: Calibration Procedure and Validation
Barbieri, M., Ceraolo, M., Lutzemberger, G., & Scarpelli, C. (2022) · Energies · doi:10.3390/en15072653 · Cited by 14
Vu, H., & Shin, D. (2023) · Journal of Energy Storage · doi:10.1016/j.est.2022.106519 · Cited by 19
Estimation of the heat generation rates in electrochemical cells
Catherino, H. A. (2013) · Journal of Power Sources · doi:10.1016/j.jpowsour.2013.03.169 · Cited by 15
A simplified physics-based model for nickel hydrogen battery
Liu, S., Dougal, R. A., Weidner, J. W., et al. (2004) · Journal of Power Sources · doi:10.1016/j.jpowsour.2004.09.035 · Cited by 15
“To simplify, we consider the heat generations due to the enthalpy of reactions [ 15 ] and the heat transported at the thermal terminal only, whereas the heat due to isometric process, enthalpy of mixing, phase change and change of specific heat are ignored without introducing significant error.”
MethodLiquid-Based Battery Temperature Control of Electric Buses
Angermeier, S., Ketterer, J., & Karcher, C. (2020) · Energies · doi:10.3390/en13194990 · Cited by 15
“[13] in 1984, various types of battery models have been presented [12,14].”
BackgroundDevelopment of 2D Thermal Battery Model for Lithium-ion Pouch Cells
Samba, A., Omar, N., Gualous, H., den Bossche, P. V., Mierlo, J. V., & Boubekeur, T. I. (2013) · World Electric Vehicle Journal · doi:10.3390/wevj6030629 · Cited by 15
Wang, K., Li, Y., Wang, B., Rao, Z., & Min, C. (2025) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2025.126665 · Cited by 17
Odungat, A., & Chanda, S. (2025) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2024.125367 · Cited by 13
Ma, X., Zhang, Y., Liu, R., et al. (2025) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2025.126063 · Cited by 14
Entropy Profiles for Li-Ion Batteries—Effects of Chemistries and Degradation
Wind, J., & Vie, P. J. S. (2025) · Entropy · doi:10.3390/e27040364 · Cited by 17
“It is well known that the developed heat from a LIB comes from both reversible and irreversible heat sources [21,22].”
Modeling Inhomogeneities during Parallel-Connected Fast Charging of Lithium-Ion Battery Systems
Frank, A., Schaeffler, S., Kirst, C., Roehrer, F., Kücher, S., Durdel, A., Scheller, M., & Jossen, A. (2025) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/adc03c · Cited by 16
Ou, Y., Zhu, J., Chen, S., Wu, H., Dai, H., & Wei, X. (2025) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2025.116146 · Cited by 16
Altan, S., & Gökaslan, M. Y. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.118137 · Cited by 18
Wang, J., Liu, B., Ding, X., et al. (2025) · Energy · doi:10.1016/j.energy.2025.138600 · Cited by 14
Vikram, S., Sadar, A., & Rakshit, D. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.119741 · Cited by 20
Sadeghian, M. S., Esfahanian, V., Akrami, M., Shokouhmand, H., Pasandeh, R., Zand, E., & Afshar, M. R. (2025) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2025.127588 · Cited by 13
A thermo-chemo-mechanically coupled model for cathode particles in lithium–ion batteries
Nateghi, A., & Keip, M. (2021) · Acta Mechanica · doi:10.1007/s00707-021-02970-1 · Cited by 14
Guo, H., Li, J., Zhu, Z., et al. (2022) · Energy Science & Engineering · doi:10.1002/ese3.1275 · Cited by 14
“Bernardi et al.27 proposed the electric‐thermal coupling model based on the assumption of uniform heat generation inside the battery cell, which showed the good prediction accuracy.”
BackgroundEfficient ways of thermal management of an EV battery
Bhosale, A. J., & Deshmukh, V. N. (2022) · Materials Today Proceedings · doi:10.1016/j.matpr.2022.09.343 · Cited by 16
Lloyd, R., & Akrami, M. (2022) · Batteries · doi:10.3390/batteries8110236 · Cited by 15
Simulation of battery simultaneous cooling based on the dual fluid medium system
Jin, S. P., Gao, Q., & Zhang, T. (2023) · Journal of Energy Storage · doi:10.1016/j.est.2023.106732 · Cited by 14
Sun, J., Dan, D., Wei, M., Cai, S., Zhao, Y., & Wright, E. (2023) · Energies · doi:10.3390/en16155815 · Cited by 19
A state of charge-aware internal preheating strategy for Li-ion batteries at low temperatures
Guan, K., Huang, Z., Liu, Y., Gao, Z., Li, H., Jiang, F., & Peng, J. (2023) · Journal of Energy Storage · doi:10.1016/j.est.2023.108585 · Cited by 14
Tousi, M., Sarchami, A., Najafi, M., & Bellur, K. (2023) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2023.121402 · Cited by 13
Verbrugge, M. W., & Baker, D. R. (2023) · ECS Advances · doi:10.1149/2754-2734/ad040e · Cited by 15
Telli, G. D., Güngör, Ş., & Lorente, S. (2023) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2023.121997 · Cited by 19
Tang, Z., Xiang, Y., Li, M., et al. (2023) · Journal of Electrochemical Energy Conversion and Storage · doi:10.1115/1.4064095 · Cited by 14
Weragoda, D. M., Tian, G., Cai, Q., Zhang, T., Lo, K. H., & Gao, Y. W. (2023) · Thermal Science and Engineering Progress · doi:10.1016/j.tsep.2023.102320 · Cited by 27
Ye, J., Peng, Z., & Tan, G. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2024.110516 · Cited by 15
Napa, N., Agrawal, M. K., & Tamma, B. (2024) · International Journal of Thermal Sciences · doi:10.1016/j.ijthermalsci.2024.108936 · Cited by 14
Bae, J., Hyun, D., & Han, J. (2024) · Batteries · doi:10.3390/batteries10020059 · Cited by 17
“Therefore, the SOC of the HVB was calculated as follows: The charge transfer and diffusion time constants of the battery are calculated as follows: The total heat generation of the battery was calculated using Bernadi’s heat generation model [34–36].”
MethodLi, M., Hu, Y., Li, L., Li, J., Wang, B., & Xia, Y. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2024.111190 · Cited by 16
Xi, Y.-A.-M., Li, Y.-Z., Chang, K.-F., & Xu, J.-L. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2024.112213 · Cited by 16
Torun, E., Buyruk, E., & Caner, M. (2025) · The European Physical Journal Plus · doi:10.1140/epjp/s13360-025-05984-z · Cited by 14
Chai, Z., Liu, Z., Xue, Q., Xiao, Y., Tan, P., Qiu, M., & Li, J. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.115917 · Cited by 20
Martín-Martín, L., Gastelurrutia, J., Larraona, G. S., Antón, R., del Portillo, L. A., & Gil, I. (2018) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2018.10.077 · Cited by 14
Kleiner, J., Lechermann, L., Komsiyska, L., Elger, G., & Endisch, C. (2021) · Journal of Energy Storage · doi:10.1016/j.est.2021.102686 · Cited by 16
Isothermal Temperature Control for Battery Testing and Battery Model Parameterization
Hales, A., Brouillet, E. V., Wang, Z., et al. (2021) · SAE International Journal of Electrified Vehicles · doi:10.4271/14-10-02-0008 · Cited by 14
Abbasalinejad, A., Besli, M. M., Hammond, J. W., et al. (2021) · Journal of Power Sources · doi:10.1016/j.jpowsour.2021.230283 · Cited by 14
Karimi, D., Behi, H., Akbarzadeh, M., et al. (2021) · Electricity · doi:10.3390/electricity2040030 · Cited by 14
“Heat generation of the LiC during its operation occurs mainly because of the ion migration process, which incorporates the electrochemical reaction, the side reaction, and the Joule losses [43].”
BackgroundSantucci, A., Sorniotti, A., & Lekakou, C. (2013) · IEEE International Electric Vehicle Conference · doi:10.1109/ievc.2013.6681147 · Cited by 14
Energy Storage Systems for Smart Grid Applications
Al-Hallaj, S., Wilke, S., & Schweitzer, B. (2017) · Water, Energy & Food Sustainability in the Middle East · doi:10.1007/978-3-319-48920-9_8 · Cited by 17
Experimental Investigation of a Lithium Battery Cooling System
Zhao, L., Wang, J., Li, Y., et al. (2019) · Sustainability · doi:10.3390/su11185020 · Cited by 14
A Comprehensive Electric Vehicle Model for Vehicle-to-Grid Strategy Development
Rücker, F., Schoeneberger, I., Wilmschen, T., Chahbaz, A., Dechent, P., Hildenbrand, F., Barbers, E., Kuipers, M., Figgener, J., & Sauer, D. U. (2022) · Energies · doi:10.3390/en15124186 · Cited by 16
“[61] the following equation describes the heat generation current Q̇ in a cell Q̇gen = Q̇irr + Q̇rev + Q̇react + Q̇mix, (1)”
Multiscale modeling of Li-ion cells: mechanics, heat generation and electrochemical kinetics
Zhang, X. (2009) · Deep Blue (University of Michigan) · Cited by 14
Saeedipour, S., Gharehghani, A., Rabiei, M., Andwari, A. M., Mehranfar, S., Reche, C. M., & Rabiei, N. (2025) · Transportation Engineering · doi:10.1016/j.treng.2025.100330 · Cited by 15
Xie, N., Yang, M., Chen, G., Lai, Z., Zhu, L., Xie, Z., Wang, S., & Zhang, Y. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.116962 · Cited by 15
Qin, Z., Yin, C., Zhang, W., Liu, D., Yao, S., Weng, W., & Han, Z. (2025) · Case Studies in Thermal Engineering · doi:10.1016/j.csite.2025.106385 · Cited by 17
Yu, H., Zhu, X., Xiaona, M. A., et al. (2025) · Case Studies in Thermal Engineering · doi:10.1016/j.csite.2025.106394 · Cited by 13
Li, J., Chen, M., Qiao, L., et al. (2025) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2025.127762 · Cited by 13
Tripathi, P. M., & Marconnet, A. M. (2025) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2025.127945 · Cited by 14
Thermal management of battery packs using direct refrigerant cooling
Zhou, S., Duan, X., Hu, S., et al. (2025) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2025.129255 · Cited by 13
Yang, H., Jiao, Z., Gu, M., Zhang, S., & Qiao, Y. (2026) · Energy · doi:10.1016/j.energy.2026.140862 · Cited by 16
Wei, F., Li, P., Zhang, Q., Shao, G., & Mao, J. (2022) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/ac6a14 · Cited by 13
Parthiv Chandra, K., Jishnu, A. K., Garg, A., et al. (2022) · International Journal of Energy Research · doi:10.1002/er.8151 · Cited by 13
Sharma, D. K., & Prabhakar, A. (2023) · Journal of Thermal Science and Engineering Applications · doi:10.1115/1.4062589 · Cited by 13
Thermal performance of cold plate based on phase change emulsion for Li-ion battery
Li, H., Piontek, U., Chen, M., et al. (2023) · Energy · doi:10.1016/j.energy.2023.128743 · Cited by 13
Yu, C., Zhu, J., Wei, X., & Dai, H. (2023) · World Electric Vehicle Journal · doi:10.3390/wevj14100271 · Cited by 13
“Among them, the typical heat generation formula derived by Bernardi has been extensively employed in considerable studies [17].”
BackgroundMakki, M., Lee, C. W., & Ayoub, G. Y. (2023) · Batteries · doi:10.3390/batteries9100502 · Cited by 13
Auch, M., Kuthada, T., & Wagner, A. (2024) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2024.123056 · Cited by 13
Li, L., Li, X., Xie, Y., Huang, H., Huang, Y., Wang, H., Bei, S., Xu, Q., Wang, X., & Zheng, K. (2024) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2024.123682 · Cited by 14
Xu, R., Li, X., Tang, S., Wang, Z., Guo, H., Peng, W., Wang, D., Duan, J., Wang, J., & Yan, G. (2023) · Applied Energy · doi:10.1016/j.apenergy.2024.123630 · Cited by 13
Vashisht, S., & Rakshit, D. (2024) · Thermal Science and Engineering Progress · doi:10.1016/j.tsep.2024.102758 · Cited by 13
Pang, H., Liu, J., Yan, X., Du, J., Wang, F., & Lin, G. (2024) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2024.124328 · Cited by 12
Gu, X., Ding, P., Chao, G., & Cui, Y. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2024.114503 · Cited by 13
Gu, J., Kim, H.-K., & Jang, S. (2024) · International Journal of Automotive Technology · doi:10.1007/s12239-024-00167-8 · Cited by 13
“(9) (Bernardi et al., 1985; Zhu et al., 2020).”
Metadata
- Authors
- Bernardi, D., Pawlikowski, E., & Newman, J.
- Affiliations
- University of California, Berkeley (US)
- ORCID
- Newman, J.
- Venue
- Journal of The Electrochemical Society
- Publisher
- The Electrochemical Society
- Published
- 1985-01-01
- Volume
- 132
- Issue
- 1
- Pages
- 5-12
- ISSN
- 0013-4651 (ISSN-L)
- 1945-7111
- OpenAlex
- W2023385933
- Cited by
- 2,548
- References
- 0
- Citations by year
- 2026: 383 · 2025: 387 · 2024: 339 · 2023: 265 · 2022: 238 · 2021: 167 · 2020: 147 · 2019: 106 · 2018: 74 · 2017: 89 · 2016: 42 · 2015: 53 · 2014: 75 · 2013: 51 · 2012: 31
- FWCI
- 0.00
- Type
- journal article
- Language
- en
- Open access
- bronze
- doi.org
- Licence
- iopscience.iop.org/page/copyright (vor, 12758 d)
- iopscience.iop.org/info/page/text-and-data-mining (tdm, 12758 d)
- Locations
- Journal of The Electrochemical Society (publishedVersion)
- Topics
- Physical Sciences › Engineering › Automotive Engineering › Battery Modeling and Management
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Advancements in Battery Materials
- Physical Sciences › Chemistry › Electrochemistry › Molten salt chemistry and electrochemical processes
- Keywords
- heat generation rate, Joule heating, phase transitions, mixing effects, electrochemical reactions, battery thermal management, battery modeling
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.