A General Energy Balance for Battery Systems
Open accessThe DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index; 2 of the 20 sources its claims cite were checked for support.
Abstract
A general energy balance for battery systems has been developed. This equation is useful for estimating cell thermal characteristics. Reliable predictions of cell temperature and heat‐generation rate are required for the design and thermal management of battery systems. The temperature of a cell changes as a result of electrochemical reactions, phase changes, mixing effects, and joule heating. The equation developed incorporates these effects in a complete and general manner. Simplifications and special cases are discussed. The results of applying the energy balance to a mathematical model of the cell discharged through two different reaction mechanisms are given as examples. The examples illustrate how the energy equation may be applied to a specific system to examine the relative contributions corresponding to the terms in the equation. The examples show that the processes involved in cell heat generation may be complex and that the application of a sufficiently general energy equation is advantageous.
Overview
CoChat Summary
TL;DR
The paper derives a general energy balance for battery systems that includes mixing, phase changes, and simultaneous electrochemical reactions with composition-dependent open-circuit potentials. It applies the equation to a modeled LiAl/LiCl-KCl/FeS cell discharged by two mechanisms and to a lead-acid estimate, showing that cell heat generation can be complex and that a sufficiently general energy equation is advantageous.
Key findings
- A general energy balance is developed that includes energy contributions from mixing, phase changes, and simultaneous electrochemical reactions with composition-dependent open-circuit potentials; prior treatments were restricted to single pure-phase reactants or a single reaction without mixing effects.
- For the LiAl/FeS model, adiabatic-reversible discharge gives the same temperature at 100% depth of discharge for both mechanisms because the overall reaction is the same; slope discontinuities occur at 50% and 12% utilization for mechanisms 1 and 2, respectively. In the realistic simulations, the second reaction begins at 30% and 11% utilization for mechanisms 1 and 2, respectively.
- The mixing term is negligible in the LiAl/FeS example; at 25% utilization, the temperature decline after current interruption is only about 0.2 K. For a lead-acid cell, the estimated temperature rise after full discharge is approximately 1.6 K, or 2.9 K if 1.25 mol of PbO2 is allowed for discharge.
- The sign of the mixing effect depends on the enthalpy curve: for lead-acid, the sulfuric acid-water enthalpy curve is concave upward, so a well-insulated cell heats after current interruption; for the high-temperature LiCl-KCl cell, the curve is concave downward, so the cell cools after interruption. Neglecting mixing overestimates lead-acid operating temperature and underestimates high-temperature cell operating temperature.
Methods
- The paper derives the energy balance from the first law of thermodynamics, assuming uniform battery temperature, and presents a final general equation including reaction, heat-capacity, phase-change, mixing, electrical-work, and heat-transfer terms.
- The equation is applied to an existing one-dimensional mathematical model of the LiAl/LiCl-KCl/FeS cell with a porous LiAl negative electrode, porous FeS positive electrode, electrolyte reservoir, and separator under galvanostatic discharge, using the two reaction mechanisms in Table I.
- Appendix A estimates the lead-acid temperature rise using an assumed uniform 5 molal sulfuric acid electrolyte, with one-third of the electrolyte in the cathode and anode spaces and one-third between the electrodes; the analysis compares adiabatic-reversible profiles with model simulations and examines the relative contributions of terms.
Limitations
- The paper states that the rigorous energy balance is difficult to apply without a detailed mathematical model because instantaneous composition profiles and current fractions are required; in practice, obtaining concentration profiles and predicting current partitioning among possible reactions is difficult.
- The paper states that the analysis does not include enthalpy changes from nonfaradaic reactions; self-discharge or corrosion must be divided into anodic and cathodic components and included as an additional term. The mixing term is also difficult because it involves integrations of concentration profiles.
- The paper states that actual FeS discharge is complicated and more like a mixture of the two proposed mechanisms plus simultaneously occurring chemical reactions; the examples are model simulations. The lead-acid estimate assumes artificial concentration jumps at interfaces, and diffusion would lower the estimate; nonuniform reaction distribution in porous electrodes would make the concentration distribution nonuniform. The breakdown is presented only up to 30% utilization because oscillatory behavior begins when the second reaction starts, to be treated in a subsequent publication.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
0 Valid · 5 Not valid · 12 Not checked · 75 Own results and interpretations
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“Basing the discharge on two Farādays (1 mol PbOg) and a transference number of 0.74 for hydrogen ion, we may calculate that the concentration in the cathode space and anode space drops to 1.04 and 2.79 molal, respectively (14).”
What the sources say
- Could not verifycites [14] 14. Hans Bode, "Lead-Acid Batteries," R. J. Brodd and K. V. Kordesch, Translators, Wiley-Interscience, New York (1977). sourceExperimental — accuracy not yet measured
The available text in the book-review passage (section labeled “Notice to Members April 1 is Cut-Off Date”; page not provided) describes the book’s theoretical treatment of lead-acid batteries but does not give this calculation. Searches for the 0.74 hydrogen-ion transference number, two Faradays, and the 1.04 and 2.79 molal concentrations found no passage addressing the claimed values. (LLM, conf=0.76)
hedgedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on 5 assumptions not shown here.
- Could not verify
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“The temperature rise, after full discharge, is approximately 1.6 K.”
- Also stated in: § Estimate of the Temperature Rise in a Lead-Acid Cell Following Current Interruption · p. 8 · hedged
“Using the data available in Ref. (14) (for 298 K), we calculate the temperature rise to be about 1.6 K”
What the sources say
- Could not verifycites [14] 14. Hans Bode, "Lead-Acid Batteries," R. J. Brodd and K. V. Kordesch, Translators, Wiley-Interscience, New York (1977). sourceExperimental — accuracy not yet measured
The available passages from the book review (page not provided) describe the book’s coverage of lead-acid battery thermodynamics but give no temperature rise after full discharge. Searches for “1.6 K” and the discharge-temperature claim found no supporting passage in our copy. (LLM, conf=0.75)
hedged- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on 5 assumptions not shown here.
- Also stated in: § Estimate of the Temperature Rise in a Lead-Acid Cell Following Current Interruption · p. 8 · hedged
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Although the mixing term offers a negligible contribution to the energy balance, it is interesting to investigate the processes that determine its behavior.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The profile for the X-phase mechanism in Fig. 1 follows the adiabatic-reversible profile up to about 5% utilization because the heat-loss contribution tends to cancel the polarization heat.”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“A general energy balance for battery systems has been developed.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on 3 assumptions not shown here.
39 more claims
Create a free account to see all 92 claims and every source verdict.
- It may state two separate claims as one. 20
- Probably not a substantial claim. 33
- The quote only partly states this claim. 1
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Conclusions · p. 8
“Equation [23], written for a single cell reaction, is the energy equation most commonly used in battery applications.”
§ Discussion of Terms · p. 5
“Furthermore, Eq. [24] is the form of the energy balance that is most commonly encountered in the literature.”
Citations
Cites
The publisher hasn’t deposited this paper’s reference list.
Research works printed but not linked: 12
- [1]1. J. M. Sherfey and A. Brenner, This Journal, 105, 665 (1958).
- [3]3. H. F. Gibbard, This Journal, 125, 353 (1978).
- [2]2. S. Gross, Energy Convers., 9, 55 (1969).
- [4]4. I. A. Dibrov and V. A. Bykov, Sov. Electrochem., 13, 298 (1977).
- [6]6. L. D. Hansen and R. M. Hart, This Journal, 125, 842 (1978).
- [5]5. I. A. Dibrov and V. A. Bykov, J. Appl. Chem., 49, 2025 (1977).
- [7]7. F. B. Tudron, ibid., 128, 516 (1981).
- [9]9. W. H. Tiedemann and J. Newman, in "Battery Design and Optimization," S. Gross, Editor, pp. 23-38, The Electrochemical Society Softbound Proceedings Series, Princeton, NJ (1979).
- [8]8. D. M. Chen and H. F. Gibbard, ibid., 130, 1975 (1983).
- [10]10. Richard Pollard and John Newman, This Journal, 128, 491 (1981).
- [11]11. Richard Pollard and John Newman, ibid., 128, 502 (1981).
- [13]13. Z. Tomczuk, S. K. Preto, and M. F. Roche, This Journal, 128, 760 (1981).
Cited by
Items 1,201–1,300 of 2,542
Su, Q., Jin, W., Kang, F., Li, J., Wang, Y., Ma, Q., Xu, S., Duan, J., Liu, Y., & Zhang, C. (2024) · International Communications in Heat and Mass Transfer · doi:10.1016/j.icheatmasstransfer.2024.108486 · Cited by 13
Effect of immersion cooling parameters on thermal and electrochemical response of a Li-ion cell
Tripathi, P. M., & Marconnet, A. M. (2025) · Journal of Power Sources · doi:10.1016/j.jpowsour.2025.236285 · Cited by 13
Thermal and electric inhomogeneity in lithium-ion battery packs
Huang, J., Long, R., Ma, L., Liu, Z., & Liu, W. (2025) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2025.126030 · Cited by 14
Tekin, A., Özdemir, T., Ekici, Ö., & Köksal, M. (2025) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2025.126545 · Cited by 17
Song, X., Jiaqiang, E., Huang, Y., et al. (2025) · Energy · doi:10.1016/j.energy.2025.137313 · Cited by 13
Development of 2D thermal battery model for Lithium-ion pouch cells
Samba, A., Omar, N., Gualous, H., den Bossche, P. V., Mierlo, J. V., & Tala-Ighil, B. (2013) · World Electric Vehicle Symposium and Exhibition (EVS) · doi:10.1109/evs.2013.6915028 · Cited by 13
Sarkar, A., Shrotriya, P., & Chandra, A. (2018) · Journal of The Electrochemical Society · doi:10.1149/2.0061809jes · Cited by 14
Thermal Management of a Li-Ion Battery for Electric Vehicles Using PCM and Water-Cooling Board
Yu, G., Chiang, S. W., Chen, W., & Du, H. D. (2019) · Key engineering materials · doi:10.4028/www.scientific.net/kem.814.307 · Cited by 13
“Battery model The Bernardi[12] model is used in this work to describe the heat generation in batteries, and the specific parameters and heat generation rate are shown in Table 3.”
MethodTang, Z., Liu, Z., Zhao, R., & Cheng, J. (2021) · Journal of Electrochemical Energy Conversion and Storage · doi:10.1115/1.4051727 · Cited by 12
Thermal reliability assessment and sensitivity analysis of 18,650 cylindrical lithium-ion battery
Yang, Z., Yu, Y., & Pak, U. (2022) · Journal of Energy Storage · doi:10.1016/j.est.2022.106504 · Cited by 14
Electrochemical-Thermal Modeling of Li-Ion Battery Packs
Fan, G., Pan, K., Bartlett, A., Canova, M., & Rizzoni, G. (2014) · ASME Dynamic Systems and Control Conference (DSCC) · doi:10.1115/dscc2014-6082 · Cited by 13
Berckmans, G. J., Ronsmans, J., Jaguemont, J., Samba, A., Omar, N., Hegazy, O., Soltani, M., Firouz, Y., den Bossche, P. V., & Mierlo, J. V. (2017) · Journal of Electrochemical Energy Conversion and Storage · doi:10.1115/1.4037491 · Cited by 13
Wang, Z., Siegel, J. B., & Garikipati, K. C. (2017) · Journal of The Electrochemical Society · doi:10.1149/2.0081712jes · Cited by 13
Application status and future of multi-scale numerical models for lithium ion battery
Cheng, Y., Li, J., Ming, J., et al. (2015) · Acta Physica Sinica · doi:10.7498/aps.64.210202 · Cited by 13
Thermal modeling of passive thermal management system with phase change material for LiFePO4 battery
Jianhua, C., Gao, D., Jiexun, L., et al. (2012) · IEEE Vehicle Power and Propulsion Conference (VPPC) · doi:10.1109/vppc.2012.6422582 · Cited by 13
Multi-Objective Optimization of Integrated Lithium-Ion Battery Thermal Management SystemPreprint
Shi, H. G., Liu, M., Li, Y., et al. (2022) · SSRN Electronic Journal · doi:10.2139/ssrn.4171524 · Cited by 13
Tahhan, A. B. A., Ramadan, M., Choi, D. S., Ahmed, R., Ghazal, M. A., & AlKhedher, M. A. (2025) · AI Thermal Fluids · doi:10.1016/j.aitf.2025.100014 · Cited by 13
Control-Oriented Galerkin-Spectral Model for 3-D Thermal Diffusion of Pouch-Type Batteries
Zhou, Y., Deng, H., & Li, H. (2022) · IEEE Transactions on Industrial Informatics · doi:10.1109/tii.2022.3212279 · Cited by 12
“Since this study is mainly concerned with reduced-order thermal modeling, we apply the Bernardi equation [15] for simplicity.”
MethodFeedback-based fault-tolerant and health-adaptive optimal charging of batteries
Sattarzadeh, S., Padisala, S. K., Shi, Y., Mishra, P. P., Smith, K. A., & Dey, S. (2023) · Applied Energy · doi:10.1016/j.apenergy.2023.121187 · Cited by 12
He, H., Chen, X., Fly, A., & Saini, V. (2023) · Journal of Power Sources · doi:10.1016/j.jpowsour.2023.233431 · Cited by 13
Li, P., Wei, Z., Wu, K., Hu, J. P., Yu, Y., & He, H. (2023) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2023.3340036 · Cited by 13
“The simplified expression proposed by Bernardi [26] from thermodynamic perspective can be calculated as follows : where I L denotes the load current, U OC denotes the open-circuit voltage, U t denotes the terminal voltage, and T a denotes the average temperature of the whole battery cell.”
BackgroundShen, K., Chen, L., Feng, X., Zheng, Y., Sun, Y., Xu, C., Wang, H., Jin, C., Han, X., Lai, X., et al. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2024.110896 · Cited by 11
Lifetime prediction of lithium-ion capacitors using electro-thermal-aging co-simulation platform
Song, S., Zhang, X., An, Y., Li, C., Zhang, X., Wang, K., Sun, X., Tang, X., & Ma, Y. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2024.111088 · Cited by 12
A Review on Cooling Methods of Lithium-Ion Battery Pack for Electric Vehicles Applications
Shaikh, U. I., Kamble, D., & Kore, S. S. (2024) · Journal of Advanced Research in Fluid Mechanics and Thermal Sciences · doi:10.37934/arfmts.115.2.113140 · Cited by 15
Lu, Y., Han, X., Lu, L., Feng, X., & Ouyang, M. (2024) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2024.3384470 · Cited by 16
“Bernardi’s theory [26] is adopted and the model is formulated as: ) where Q gen is the total heat generation which mainly includes the Joule heat and the reaction heat.”
MethodKavasoğullari, B., Karagöz, M. E., Önel, M. N., Yıldız, A. S., & Biçer, E. (2024) · Numerical Heat Transfer Part A Applications · doi:10.1080/10407782.2024.2363506 · Cited by 13
“[40]: In Eq.”
Conceptual design of a tilt-rotor unmanned aerial vehicle for Mars exploration
Ge, J., Xiang, J., Li, D., & Bai, W. (2024) · Acta Astronautica · doi:10.1016/j.actaastro.2024.06.010 · Cited by 12
Chen, L., Tong, B., Li, S., et al. (2024) · Transactions of Nonferrous Metals Society of China · doi:10.1016/s1003-6326(24)66517-9 · Cited by 12
Zheng, S., Zhang, Y., Dan, D., Wei, M., Zhao, Y., Li, M., & Xie, Y. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2024.113468 · Cited by 13
Xu, Q., Xie, Y., Lin, X., et al. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2024.114032 · Cited by 12
Comprehensive Study on Thermal Characteristics of Lithium‐Ion Battery With Entropic Heat
Chun, H., Choi, H., Jun, Y., & Lee, H. (2024) · International Journal of Energy Research · doi:10.1155/2024/8815580 · Cited by 14
Online core temperature estimation method for lithium-ion batteries over the entire lifecycle
Chen, S., Wang, Z., Zhang, P., Yu, Y., Liu, X., Li, L., & Sun, J. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2024.115033 · Cited by 13
Lu, H., Kadirgama, K., & Noor, M. M. (2024) · Frontiers in Heat and Mass Transfer · doi:10.32604/fhmt.2024.059871 · Cited by 12
Bao, J., Mao, Y., Zhang, Z., Jiang, Y., Zhang, Y., & Yang, Y. K. (2024) · International Journal of Energy Research · doi:10.1155/er/5544635 · Cited by 12
Zhang, B., Chen, Z., Jiao, M., et al. (2025) · Applied Energy · doi:10.1016/j.apenergy.2025.125872 · Cited by 12
Li, Z., Zhang, J., & Wu, B. (2014) · Scientia Sinica Technologica · doi:10.1360/n092014-00226 · Cited by 12
Lithium-Ion Capacitor - Optimization of Thermal Management from Cell to Module Level
Berckmans, G. J., Jaguemont, J., Soltani, M., Samba, A., Boninsegna, M., Omar, N., Hegazy, O., Mierlo, J. V., & Ronsmans, J. (2016) · IEEE Vehicle Power and Propulsion Conference (VPPC) · doi:10.1109/vppc.2016.7791721 · Cited by 12
“The heat source in the electrode domain is computed from the Bernardi equation [29], where the generation term can be simplified as: = ( − ) − (3)”
MethodYang, Y., Xu, X., Li, W., & Tong, G. (2020) · International Journal of Energy Research · doi:10.1002/er.5579 · Cited by 12
Suo, Y., & Liu, J. (2020) · International Journal of Energy Research · doi:10.1002/er.5892 · Cited by 12
“At a fixed spatial position and a given time, the temperature in the LIBs is higher for the higher discharge current because the heat generation Q of Equation (7) is higher when discharge current is higher and higher heat generation causes higher temperature.”
BackgroundA CFD thermal analysis and validation of a Li-ion pouch cell under different temperatures conditions
Estevez, M. A. P., Caligiuri, C., & Renzi, M. (2021) · E3S Web of Conferences · doi:10.1051/e3sconf/202123809003 · Cited by 14
“The heat generation equation, equation 5, was proposed by Bernardi et al in [15].”
BackgroundIdentifying Efficient Cooling Approach of Cylindrical Lithium‐Ion Batteries
Ahmad, T., Mishra, A., Ghosh, S., & Casari, C. S. (2021) · Energy Technology · doi:10.1002/ente.202100888 · Cited by 12
Li, Y., Liu, H., & Ye, M. (2022) · IEEE Access · doi:10.1109/access.2022.3169783 · Cited by 12
“As a result, the total heat generation can is calculated using (8): 𝑄𝑄 = 𝐼𝐼𝐼𝐼𝐼𝐼 � 𝜕𝜕𝜕𝜕 𝜕𝜕𝐼𝐼 � 𝑃𝑃 + 𝐼𝐼2𝑅𝑅𝑗𝑗𝐼𝐼 + 𝐼𝐼2𝑅𝑅𝑝𝑝𝐼𝐼 (8) The corresponding heat production per unit time and unit volume is calculated using Equations (4)-(8) and the model proposed by Bernardi [25]as shown in (9): 𝑞𝑞 = 𝐼𝐼 𝑉𝑉 �𝐼𝐼 𝜕𝜕𝜕𝜕 𝜕𝜕𝐼𝐼 + 𝐼𝐼�𝑅𝑅𝑗𝑗 +…”
Heat Generation and Temperature Rise Characteristics of Single Overcharged Lithium-Ion Batteries
Zhang, Q., Li, P., Liu, C., Wei, F., Wang, M., Li, J., Zhu, S., Shao, G., & Mao, J. (2022) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/ac725a · Cited by 12
Liu, Y., Xu, S., Wang, Y., & Dong, H. (2022) · International Journal of Thermophysics · doi:10.1007/s10765-022-03058-1 · Cited by 11
Shi, Y., Guan, L., Gao, C., Shen, A., Chen, B., Zhou, J., & Cai, R. (2022) · International Journal of Solids and Structures · doi:10.1016/j.ijsolstr.2022.112046 · Cited by 11
Brown, D., & Landers, R. G. (2012) · Journal of The Electrochemical Society · doi:10.1149/2.065212jes · Cited by 12
Methodology for thermal modelling of lithium-ion batteries
Iraola, U., Aizpuru, I., Canales, J. M. F., et al. (2013) · Proceedings of the Annual Conference of the IEEE Industrial Electronics Society · doi:10.1109/iecon.2013.6700250 · Cited by 12
Liu, G., Lu, L., Li, J., & Ouyang, M. (2013) · IEEE Vehicle Power and Propulsion Conference (VPPC) · doi:10.1109/vppc.2013.6671721 · Cited by 12
Modeling and Simulation of Lithium-Ion Batteries from Systems Engineering Perspective
Ramadesigan, V., Northrop, P. W. C., De, S., Santhanagopalan, S., Braatz, R. D., & Subramanian, V. R. (2010) · ECS Meeting Abstracts · doi:10.1149/2.018203jes · Cited by 12
Thermal Model Parameter Identification of a Lithium Battery
Nissing, D., Mahanta, A., & van Sterkenburg, S. (2017) · Journal of Control Science and Engineering · doi:10.1155/2017/9543781 · Cited by 13
Optimal-Sensing-Based Recursive Estimation for Temperature Distribution of Pouch-Type Batteries
Zhou, Y., Deng, H., & Li, H. (2022) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2022.3171857 · Cited by 12
Thermal behavior of nickel/metal hydride battery during charging and discharging
Yang, K., Li, D., Chen, S., et al. (2009) · Journal of Thermal Analysis and Calorimetry · doi:10.1007/s10973-008-9257-y · Cited by 12
Thermal modeling for vehicle battery system: A brief review
Li, H., Li, H. X., & Li, H. X. (2012) · International Conference on System Science and Engineering · doi:10.1109/icsse.2012.6257152 · Cited by 12
“[2] studied the thermal behavior of batteries through mathematical modeling, and derived a heat generation term which can be simplified as:”
BackgroundXue, B., Zhou, Y., Chen, P., Meng, X., & Zhang, J. (2025) · Processes · doi:10.3390/pr13030651 · Cited by 11
Ma, M., Xu, Q., Chen, Q., Jiang, T., & Wang, H. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.117414 · Cited by 11
Cao, M., He, Q., Zhu, X., et al. (2025) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2025.128129 · Cited by 11
Wang, Y., Wang, C., Li, D., & Xi, H. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.119078 · Cited by 12
Evaluation of Commercial Sodium-Ion Batteries by State-of-the-Art Lithium-Ion Battery Configurations
Droese, D., Luc, P.-M., Otto, M., Schlösser, A. E. K., Evans, D. A., & Kowal, J. (2025) · Batteries · doi:10.3390/batteries11110420 · Cited by 11
“In addition, the heat source shows a chemistry-dependent behavior for both the irreversible heat due to electrical losses and the reversible heat by entropy changes of the cell electrodes [40].”
Cao, H., Lin, Z., Zhang, D., et al. (2025) · Energy · doi:10.1016/j.energy.2025.139591 · Cited by 11
A comprehensive review of hybrid liquid and PCM cooling BTMS
Liu, J., Zhang, X., Xi, Y., Xu, S., & Zhang, Z. (2025) · Journal of Thermal Analysis and Calorimetry · doi:10.1007/s10973-025-15014-w · Cited by 12
Thermal Behavior of an Intelligent Li-Ion Cell under Vehicle Conditions
Kleiner, J., Heider, A., Hanzl, C., Komsiyska, L., Elger, G., & Endisch, C. (2020) · Annual Conference of the IEEE Industrial Electronics Society (IECON) · doi:10.1109/iecon43393.2020.9254336 · Cited by 13
“[14]:”
Zhang, W., Zhang, J., Zhang, G., Hu, Y., Jiang, L., Wen, Y., & Shao, D. (2024) · Energies · doi:10.3390/en17040939 · Cited by 16
“Based on a prior study, the D. Bernardi heat generation model [46] was utilized to examine the heat generation behavior and compute the battery ʹ s temperature variation, as shown below: where 𝑞(cid:4662) is the heat generation of the battery, I is the charging and discharging current, V is the…”
MethodNumerical Analysis of the Thermal Management Strategies of Electric Vehicle Battery: A Review
Paval, P. S., Sharma, T. K., Mallisetty, P. K., Chandrakanth, B., & Reddy, T. S. (2024) · Archives of Computational Methods in Engineering · doi:10.1007/s11831-024-10068-9 · Cited by 12
“Bernardi et al. [41] developed this general simplified ‘thermal–electrochemical’ model based lumped parameter approach.”
Dielectric flow- and tab-based battery thermal management system for EV high performance application
Gonzalez-Aguirre, E., Gastelurrutia, J., Oca, L., del Portillo, L. A., & Goienetxe, L. E. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2024.111401 · Cited by 12
Improved Thermal Management of Li-Ion Batteries with Phase-Change Materials and Metal Fins
Paciolla, P., & Papurello, D. (2024) · Batteries · doi:10.3390/batteries10060190 · Cited by 17
Peng, D., Xiaoyong, G., Meijuan, Z., et al. (2024) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2024.124686 · Cited by 11
Lu, Y., Li, Y., Han, X., Feng, X., Lu, L., & Ouyang, M. (2024) · Applied Energy · doi:10.1016/j.apenergy.2024.124747 · Cited by 16
Safety and Reliability Analysis of Reconfigurable Battery Energy Storage System
Xu, H., Cheng, L., Paizulamu, D., et al. (2024) · Batteries · doi:10.3390/batteries11010012 · Cited by 11
“A simplified model is proposed for heat generation, assuming a uniform change in the internal temperature field [29].”
Shamnaz, M., Bal, D. K., & Sahoo, B. B. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.115584 · Cited by 15
Bidwaik, A. S., Bhusnoor, S. S., & Nikam, S. R. (2025) · Engineering Research Express · doi:10.1088/2631-8695/add3c4 · Cited by 12
Couto, L. D., Capron, O., Servotte, J., Ponnette, R., & Mulder, G. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.116739 · Cited by 16
Li, J., Yang, J., Sun, Y., et al. (2025) · Renewable Energy · doi:10.1016/j.renene.2025.123928 · Cited by 11
Vu, H., & Shin, D. (2020) · Energies · doi:10.3390/en13092212 · Cited by 12
“The thermal balance of a battery cell with internal heat generation and external conduction were analysed in [23] and are expressed as:”
BackgroundTraskunov, I., & Latz, A. (2020) · Energy Technology · doi:10.1002/ente.202000861 · Cited by 11
Research on Influencing Factors About Temperature of Short Circuit Area in Lithium-Ion Power Battery
Wenwei, W., Fenghao, Z., & Li, Y. (2020) · Journal of Electrochemical Energy Conversion and Storage · doi:10.1115/1.4049470 · Cited by 12
Cui, X., Chen, S., Xiao, M., et al. (2021) · Journal of Electrochemical Energy Conversion and Storage · doi:10.1115/1.4050509 · Cited by 11
Zhuang, Y., Shen, W., Yan, J., Wang, L., Zhou, C. H., Lei, P., Zhong, M., Zhang, J., & Guo, S. (2022) · ACS Applied Energy Materials · doi:10.1021/acsaem.2c00026 · Cited by 11
Degla, A., Chikh, M., Mahrane, A., & Arab, A. H. (2022) · International Journal of Energy Research · doi:10.1002/er.7899 · Cited by 13
Yin, L., Geng, Z., Bjorneklett, A., Söderlund, E., Thiringer, T., & Brandell, D. (2022) · Energy Technology · doi:10.1002/ente.202101131 · Cited by 11
Chen, S., Sun, J., Qiu, S., Liu, X., Lyu, K., Chen, S., Xing, S., & Guo, Y. (2023) · Journal of Energy Storage · doi:10.1016/j.est.2023.106752 · Cited by 10
Isothermal calorimeter heat measurements of a 20Ah lithium iron phosphate battery cell
Millet, L., Bruch, M., Raab, P., Lux, S., & Vetter, M. (2017) · International Conference on Ecological Vehicles and Renewable Energies (EVER) · doi:10.1109/ever.2017.7935957 · Cited by 13
Transient Thermal Behavior of Internal Short-circuit in Lithium Iron Phosphate Battery
Zheng, J., Xu, Y., Gao, X., Zheng, J., He, H., & Li, Z. (2018) · International Journal of Electrochemical Science · doi:10.20964/2018.12.73 · Cited by 11
Jindal, P., & Bhattacharya, J. (2020) · International Journal of Energy Research · doi:10.1002/er.5303 · Cited by 11
“At first, the state of the art method is utilized to evaluate the rate of heat generation at different discharge rates in Li-ion batteries.(18,21,37) This method uses the electrical and temperature measurements of the Li-ion cell during discharge to provide the heat generation rate.”
MethodHeat generation and a conservation law for chemical energy in Li-ion batteries
Richardson, G. W., & Korotkin, I. (2021) · Electrochimica Acta · doi:10.1016/j.electacta.2021.138909 · Cited by 11
“This method of estimating the energy dissipation is based on thermodynamic treatments by Rao and Newman [27] and Gu and Wang [15], which are ultimately based on the work of Bernardi [3].”
MethodThermal Management of a 48 V Lithium-Ion Battery Pack by Semiconductor Refrigeration
Yang, R., Li, K., Xie, Y., Li, W., Qian, Y., Zhang, Y., & Zhang, H. (2022) · Frontiers in Energy Research · doi:10.3389/fenrg.2021.794438 · Cited by 13
“The battery energy balance system proposed by Bernardi (Bernardi et al., 1985) provides a theoretical basis for calculating battery heat production.”
BackgroundRole of lithium salt in reducing the internal heating of a lithium ion battery during fast charging
Badwekar, K., Dingari, N. N., Mynam, M., & Rai, B. (2022) · Journal of Applied Electrochemistry · doi:10.1007/s10800-022-01681-2 · Cited by 11
“Primitive approaches involved calorimetry experiments to calculate the heat output for batteries [14].”
MethodIterative Dynamic Programming Strategy for Electric Vehicle Battery Thermal Management Optimization
Ma, Y., & Li, J. (2022) · Advanced Theory and Simulations · doi:10.1002/adts.202100602 · Cited by 11
Ahmad, A. M., Thenaisie, G., & Lee, S. (2022) · Journal of Power Sources Advances · doi:10.1016/j.powera.2022.100097 · Cited by 10
The influence of hydrogen intercalation on inner pressure of Ni/MH battery during fast charge
Shi, J., Wu, F., Hu, D., et al. (2006) · Journal of Power Sources · doi:10.1016/j.jpowsour.2006.04.076 · Cited by 11
A Temperature-Based Peak Power Capability Estimation Method for Lithium-Ion Batteries
Jiang, W.-J., Zhang, N., Li, P., & Chen, N. (2017) · Procedia Engineering · doi:10.1016/j.proeng.2017.04.372 · Cited by 11
Safer Batteries through Coupled Multiscale Modeling
Turner, J., Allu, S., Berrill, M., Elwasif, W. R., Kalnaus, S., Kumar, A., Lebrun-Grandié, D., Pannala, S., & Simunovic, S. (2015) · Procedia Computer Science · doi:10.1016/j.procs.2015.05.286 · Cited by 11
Control-Oriented Model for Thermal Energy Management of Battery Electric Vehicles
Lokur, P., Murgovski, N., & Larsson, M. (2024) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2024.3508022 · Cited by 11
“The first term in (11) corresponds to the heat generation due to the battery’s internal resistance, the second term corresponds to the heat generation due to a reversible process [34], [35], and the last term corresponds to the heat generation due to the bus bar resistance R br .”
Transient Thermal Simulation of Lithium‐Ion Batteries for Hybrid/Electric Vehicles
Vinten, N., Jianu, O. A., El-Sharkawy, A. E., & Arora, D. (2024) · Energy Technology · doi:10.1002/ente.202401331 · Cited by 10
Bidwaik, A. S., Bhusnoor, S. S., & Nikam, S. R. (2025) · Journal of the Brazilian Society of Mechanical Sciences and Engineering · doi:10.1007/s40430-025-05810-8 · Cited by 13
“A model was developed by Bernardi et al. [6] to demonstrate heat generation in a single battery during charging and discharging, as shown in Eq.”
Han, J., Kim, J., Ryu, M., & Lee, B. J. (2025) · Case Studies in Thermal Engineering · doi:10.1016/j.csite.2025.106902 · Cited by 11
Shen, K., Yuan, J.-Q., Ding, P., He, B., Song, G., Pang, X.-H., Lu, Y.-F., Lai, X., Meng, X., Feng, X.-N., et al. (2025) · eTransportation · doi:10.1016/j.etran.2025.100496 · Cited by 11
A review of MOF-based composite phase change materials for battery thermal management
Zhao, X., Fang, M., Liu, Y., Fei, H., & Guo, W. (2025) · Chemical Communications · doi:10.1039/d5cc04811g · Cited by 10
Zi, J., Long, W., Lin, T., & Zhao, R. (2025) · International Journal of Thermal Sciences · doi:10.1016/j.ijthermalsci.2025.110401 · Cited by 12
Fan, X., Wang, Z., Wang, J., et al. (2025) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2025.128500 · Cited by 10
Li, S.-Y., & Fetene, M. G. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.118537 · Cited by 10
Metadata
- Authors
- Bernardi, D., Pawlikowski, E., & Newman, J.
- Affiliations
- University of California, Berkeley (US)
- ORCID
- Newman, J.
- Venue
- Journal of The Electrochemical Society
- Publisher
- The Electrochemical Society
- Published
- 1985-01-01
- Volume
- 132
- Issue
- 1
- Pages
- 5-12
- ISSN
- 0013-4651 (ISSN-L)
- 1945-7111
- OpenAlex
- W2023385933
- Cited by
- 2,548
- References
- 0
- Citations by year
- 2026: 383 · 2025: 387 · 2024: 339 · 2023: 265 · 2022: 238 · 2021: 167 · 2020: 147 · 2019: 106 · 2018: 74 · 2017: 89 · 2016: 42 · 2015: 53 · 2014: 75 · 2013: 51 · 2012: 31
- FWCI
- 0.00
- Type
- journal article
- Language
- en
- Open access
- bronze
- doi.org
- Licence
- iopscience.iop.org/page/copyright (vor, 12758 d)
- iopscience.iop.org/info/page/text-and-data-mining (tdm, 12758 d)
- Locations
- Journal of The Electrochemical Society (publishedVersion)
- Topics
- Physical Sciences › Engineering › Automotive Engineering › Battery Modeling and Management
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Advancements in Battery Materials
- Physical Sciences › Chemistry › Electrochemistry › Molten salt chemistry and electrochemical processes
- Keywords
- heat generation rate, Joule heating, phase transitions, mixing effects, electrochemical reactions, battery thermal management, battery modeling
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.