The DOI matches its Crossref record; 85 of the 85 references it cites were found in a registry or an index.
Optimisation of Strength Properties of FDM Printed Parts—A Critical Review
Open accessAbstract
Additive Manufacturing is currently growing fast, especially fused deposition modeling (FDM), also known as fused filament fabrication (FFF). When manufacturing parts use FDM, there are two key parameters—strength of the part and dimensional accuracy—that need to be considered. Although FDM is a popular technology for fabricating prototypes with complex geometry and other part product with reduced cycle time, it is also limited by several drawbacks including inadequate mechanical properties and reduced dimensional accuracy. It is evident that part qualities are greatly influenced by the various process parameters, therefore an extensive review of the effects of the following process parameters was carried out: infill density, infill patterns, extrusion temperature, layer thickness, nozzle diameter, raster angle and build orientation on the mechanical properties. It was found from the literature that layer thickness is the most important factor among the studied ones. Although manipulation of process parameters makes significant differences in the quality and mechanical properties of the printed part, the ideal combination of parameters is challenging to achieve. Hence, this study also includes the influence of pre-processing of the printed part to improve the part strength and new research trends such as, vacuum-assisted FDM that has shown to improve the quality of the printing due to improved bonding between the layers. Advances in materials and technologies that are currently under development are presented. For example, the pre-deposition heating method, using an IR lamp of other technologies, shows a positive impact on the mechanical properties of the printed parts.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
3D printing of polymer matrix composites: A review and prospective
Wang, X., Jiang, M., Zhou, Z., Gou, J., & Hui, D. (2017) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2016.11.034 · Cited by 3,325
Gibson, I., Rosen, D., & Stucker, B. (2015) · doi:10.1007/978-1-4939-2113-3 · Cited by 3,299
Ning, F., Cong, W., Qiu, J., Wei, J., & Wang, S. (2015) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2015.06.013 · Cited by 1,718
Highly oriented carbon fiber–polymer composites via additive manufacturing
Tekinalp, H. L., Kunc, V., Velez-Garcia, G. M., Duty, C. E., Love, L. J., Naskar, A. K., Blue, C. A., & Ozcan, S. (2014) · Composites Science and Technology · doi:10.1016/j.compscitech.2014.10.009 · Cited by 1,514
Mohamed, O. A., Masood, S. H., & Bhowmik, J. L. (2015) · Advances in Manufacturing · doi:10.1007/s40436-014-0097-7 · Cited by 1,481
A review of melt extrusion additive manufacturing processes: I. Process design and modeling
N. Turner, B., Strong, R., & A. Gold, S. (2014) · Rapid Prototyping Journal · doi:10.1108/rpj-01-2013-0012 · Cited by 1,450
The future of dental devices is digital
van Noort, R. (2012) · Dental Materials · doi:10.1016/j.dental.2011.10.014 · Cited by 1,408
Parametric appraisal of mechanical property of fused deposition modelling processed parts
Sood, A. K., Ohdar, R. K., & Mahapatra, S. S. (2010) · Materials & Design · doi:10.1016/j.matdes.2009.06.016 · Cited by 1,318
Effect of processing conditions on the bonding quality of FDM polymer filaments
Sun, Q., Rizvi, G. M., Bellehumeur, C. T., & Gu, P. (2008) · Rapid Prototyping Journal · doi:10.1108/13552540810862028 · Cited by 1,277
A review on additive manufacturing of polymer-fiber composites
Parandoush, P., & Lin, D. (2017) · Composite Structures · doi:10.1016/j.compstruct.2017.08.088 · Cited by 1,270
Hutmacher, D. W., Sittinger, M., & Risbud, M. V. (2004) · Trends in Biotechnology · doi:10.1016/j.tibtech.2004.05.005 · Cited by 1,121
A theory crack healing in polymers
Wool, R. P., & O’Connor, K. M. (1981) · Journal of Applied Physics · doi:10.1063/1.328526 · Cited by 1,093
FDM process parameters influence over the mechanical properties of polymer specimens: A review
Popescu, D., Zapciu, A., Amza, C., Baciu, F., & Marinescu, R. (2018) · Polymer Testing · doi:10.1016/j.polymertesting.2018.05.020 · Cited by 1,015
Development of biocompatible synthetic extracellular matrices for tissue engineering
Kim, B.-S., & Mooney, D. J. (1998) · Trends in Biotechnology · doi:10.1016/s0167-7799(98)01191-3 · Cited by 931
Rapid prototyping in tissue engineering: challenges and potential
Yeong, W.-Y., Chua, C.-K., Leong, K.-F., & Chandrasekaran, M. (2004) · Trends in Biotechnology · doi:10.1016/j.tibtech.2004.10.004 · Cited by 807
Turner, B. N., & Gold, S. A. (2015) · Rapid Prototyping Journal · doi:10.1108/rpj-02-2013-0017 · Cited by 770
Modeling of Bond Formation Between Polymer Filaments in the Fused Deposition Modeling Process
Bellehumeur, C., Li, L., Sun, Q., & Gu, P. (2004) · Journal of Manufacturing Processes · doi:10.1016/s1526-6125(04)70071-7 · Cited by 768
A review of rapid prototyping techniques for tissue engineering purposes
Peltola, S. M., Melchels, F. P. W., Grijpma, D. W., & Kellomäki, M. (2008) · Annals of Medicine · doi:10.1080/07853890701881788 · Cited by 751
Review of additive manufacturing technologies and applications in the aerospace industry
Najmon, J. C., Raeisi, S., & Tovar, A. (2019) · Additive Manufacturing for the Aerospace Industry · doi:10.1016/b978-0-12-814062-8.00002-9 · Cited by 719
Ning, F., Cong, W., Hu, Y., & Wang, H. (2017) · Journal of Composite Materials · doi:10.1177/0021998316646169 · Cited by 632
Mechanical characterization of parts fabricated using fused deposition modeling
Bellini, A., & Güçeri, S. (2003) · Rapid Prototyping Journal · doi:10.1108/13552540310489631 · Cited by 628
(1945) · Medical Entomology and Zoology · Cited by 618
Scaffold development using 3D printing with a starch-based polymer
Lam, C. X. F., Mo, X. M., Teoh, S. H., & Hutmacher, D. W. (2002) · Materials Science and Engineering: C · doi:10.1016/s0928-4931(02)00012-7 · Cited by 614
Weng, Z., Wang, J., Senthil, T., & Wu, L. (2016) · Materials & Design · doi:10.1016/j.matdes.2016.04.045 · Cited by 609
Durgun, I., & Ertan, R. (2014) · Rapid Prototyping Journal · doi:10.1108/rpj-10-2012-0091 · Cited by 530
Fused deposition modelling with ABS–graphene nanocomposites
Dul, S., Fambri, L., & Pegoretti, A. (2016) · Composites Part A: Applied Science and Manufacturing · doi:10.1016/j.compositesa.2016.03.013 · Cited by 491
Nanofiber‐reinforced polymers prepared by fused deposition modeling
Shofner, M. L., Lozano, K., Rodríguez‐Macías, F. J., & Barrera, E. V. (2003) · Journal of Applied Polymer Science · doi:10.1002/app.12496 · Cited by 484
Rodríguez-Panes, A., Claver, J., & Camacho, A. M. (2018) · Materials · doi:10.3390/ma11081333 · Cited by 477
Fused deposition modelling: a review
Vyavahare, S., Teraiya, S., Panghal, D., & Kumar, S. (2019) · Rapid Prototyping Journal · doi:10.1108/rpj-04-2019-0106 · Cited by 426
Melocchi, A., Parietti, F., Maroni, A., Foppoli, A., Gazzaniga, A., & Zema, L. (2016) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2016.05.036 · Cited by 409
Torrado, A. R., Shemelya, C. M., English, J. D., Lin, Y., Wicker, R. B., & Roberson, D. A. (2015) · Additive Manufacturing · doi:10.1016/j.addma.2015.02.001 · Cited by 406
Rodríguez, J. F., Thomas, J. P., & Renaud, J. E. (2001) · Rapid Prototyping Journal · doi:10.1108/13552540110395547 · Cited by 362
Yin, J., Lu, C., Fu, J., Huang, Y., & Zheng, Y. (2018) · Materials & Design · doi:10.1016/j.matdes.2018.04.029 · Cited by 360
Additive Manufacturing Technologies – Rapid Prototyping to Direct Digital Manufacturing
Mueller, B. (2012) · Assembly Automation · doi:10.1108/aa.2012.03332baa.010 · Cited by 359
Garzon-Hernandez, S., Garcia-Gonzalez, D., Jérusalem, A., & Arias, A. (2020) · Materials & Design · doi:10.1016/j.matdes.2019.108414 · Cited by 350
Wang, X., Zhao, L., Fuh, J. Y. H., & Lee, H. P. (2019) · Polymers · doi:10.3390/polym11071154 · Cited by 331
Omar, O. M., MOHAMED, M., SyedH., Masood, ., & Bhowmik (2015) · Acta Scientiarum Naturalium Universitatis Sunyatseni · Cited by 302
Akhoundi, B., & Behravesh, A. H. (2019) · Experimental Mechanics · doi:10.1007/s11340-018-00467-y · Cited by 297
Okwuosa, T. C., Stefaniak, D., Arafat, B., Isreb, A., Wan, K.-W., & Alhnan, M. A. (2016) · Pharmaceutical Research · doi:10.1007/s11095-016-1995-0 · Cited by 294
Kishore, V., Ajinjeru, C., Nycz, A., Post, B., Lindahl, J., Kunc, V., & Duty, C. (2017) · Additive Manufacturing · doi:10.1016/j.addma.2016.11.008 · Cited by 292
Cuan-Urquizo, E., Barocio, E., Tejada-Ortigoza, V., Pipes, R. B., Rodriguez, C. A., & Roman-Flores, A. (2019) · Materials · doi:10.3390/ma12060895 · Cited by 288
Modification of Frenkel's model for sintering
Pokluda, O., Bellehumeur, C. T., & Vlachopoulos, J. (1997) · AIChE Journal · doi:10.1002/aic.690431213 · Cited by 281
Part strength evolution with bonding between filaments in fused deposition modelling
Gurrala, P. K., & Regalla, S. P. (2014) · Virtual and Physical Prototyping · doi:10.1080/17452759.2014.913400 · Cited by 262
Benwood, C., Anstey, A., Andrzejewski, J., Misra, M., & Mohanty, A. K. (2018) · ACS Omega · doi:10.1021/acsomega.8b00129 · Cited by 262
Biodegradable and bioactive porous scaffold structures prepared using fused deposition modeling
Korpela, J., Kokkari, A., Korhonen, H., Malin, M., Närhi, T., & Seppälä, J. (2013) · Journal of Biomedical Materials Research Part B: Applied Biomaterials · doi:10.1002/jbm.b.32863 · Cited by 258
Direct 3D printing of polymers onto textiles: experimental studies and applications
Pei, E., Shen, J., & Watling, J. (2015) · Rapid Prototyping Journal · doi:10.1108/rpj-09-2014-0126 · Cited by 240
Xu, N., Ye, X., Wei, D., Zhong, J., Chen, Y., Xu, G., & He, D. (2014) · ACS Applied Materials & Interfaces · doi:10.1021/am502716t · Cited by 231
The influence of printing parameters on selected mechanical properties of FDM/FFF 3D-printed parts
Ćwikła, G., Grabowik, C., Kalinowski, K., Paprocka, I., & Ociepka, P. (2017) · IOP Conference Series Materials Science and Engineering · doi:10.1088/1757-899x/227/1/012033 · Cited by 226
Ravi, A. K., Deshpande, A., & Hsu, K. H. (2016) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2016.08.007 · Cited by 217
Sezer, H. K., & Eren, O. (2018) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2018.12.004 · Cited by 217
Investigation of infill-patterns on mechanical response of 3D printed poly-lactic-acid
Aloyaydi, B. A., Sivasankaran, S., & Mustafa, A. (2020) · Polymer Testing · doi:10.1016/j.polymertesting.2020.106557 · Cited by 208
Bond and part strength in fused deposition modeling
Coogan, T. J., & Kazmer, D. O. (2017) · Rapid Prototyping Journal · doi:10.1108/rpj-03-2016-0050 · Cited by 206
Warpage of FDM parts: Experimental tests and analytic model
Armillotta, A., Bellotti, M., & Cavallaro, M. (2018) · Robotics and Computer-Integrated Manufacturing · doi:10.1016/j.rcim.2017.09.007 · Cited by 193
Chohan, J. S., Singh, R., Boparai, K. S., Penna, R., & Fraternali, F. (2017) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2017.02.045 · Cited by 185
Fused deposition modeling of patient‐specific polymethylmethacrylate implants
Espalin, D., Arcaute, K., Rodriguez, D., Medina, F., Posner, M., & Wicker, R. (2010) · Rapid Prototyping Journal · doi:10.1108/13552541011034825 · Cited by 176
Liu, X., Zhang, M., Li, S., Si, L., Peng, J., & Yuan, H. (2016) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-016-9263-3 · Cited by 176
Fused Deposition Modeling for Unmanned Aerial Vehicles (UAVs): A Review
Klippstein, H., Diaz De Cerio Sanchez, A., Hassanin, H., Zweiri, Y., & Seneviratne, L. (2018) · Advanced Engineering Materials · doi:10.1002/adem.201700552 · Cited by 176
Evaluation of dimensional accuracy and material properties of the MakerBot 3D desktop printer
Melenka, G. W., Schofield, J. S., Dawson, M. R., & Carey, J. P. (2015) · Rapid Prototyping Journal · doi:10.1108/rpj-09-2013-0093 · Cited by 169
Experimental Investigations for Optimizing the Extrusion Parameters on FDM PLA Printed Parts
Yang, L., Li, S., Li, Y., Yang, M., & Yuan, Q. (2018) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-018-3784-x · Cited by 166
Raju, M., Gupta, M. K., Bhanot, N., & Sharma, V. S. (2019) · Journal of Intelligent Manufacturing · doi:10.1007/s10845-018-1420-0 · Cited by 161
Healing simulation for bond strength prediction of FDM
Coogan, T. J., & Kazmer, D. O. (2017) · Rapid Prototyping Journal · doi:10.1108/rpj-03-2016-0051 · Cited by 158
Panda, S. K., Padhee, S., Sood, A. K., & Mahapatra, S. S. (2009) · Intelligent Information Management · doi:10.4236/iim.2009.12014 · Cited by 150
Rapid investment casting: direct and indirect approaches via fused deposition modelling
Cheah, C. M., Tan, L. H., Feng, C., Lee, C.-W., & Chua, C. K. (2004) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-003-1694-y · Cited by 149
Spoerk, M., Arbeiter, F. J., Raguž, I., Weingrill, G., Fischinger, T., Traxler, G., Schuschnigg, S., Cardon, L., & Holzer, C. (2018) · Macromolecular Materials and Engineering · doi:10.1002/mame.201800179 · Cited by 149
Studies on Parametric Optimization for Fused Deposition Modelling Process
Nidagundi, V. B., Keshavamurthy, R., & Prakash, C. (2015) · Materials Today Proceedings · doi:10.1016/j.matpr.2015.07.097 · Cited by 137
Zhang, B., Seong, B., Nguyen, V., & Byun, D. (2016) · Journal of Micromechanics and Microengineering · doi:10.1088/0960-1317/26/2/025015 · Cited by 134
Haryńska, A., Gubanska, I., Kucińska‐Lipka, J., & Janik, H. (2018) · Polymers · doi:10.3390/polym10121304 · Cited by 125
Influence of fused deposition modeling parameters on the mechanical properties of ABS parts
Vicente, C. M. S., Martins, T. S., Leite, M., Ribeiro, A., & Reis, L. G. (2019) · Polymers for Advanced Technologies · doi:10.1002/pat.4787 · Cited by 125
An improved fused deposition modeling process for forming large-size thin-walled parts
Du, J., Wei, Z., Wang, X., Wang, J., & Chen, Z. (2016) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2016.04.005 · Cited by 111
Triyono, J., Sukanto, H., Saputra, R. M., & Smaradhana, D. F. (2020) · Open Engineering · doi:10.1515/eng-2020-0083 · Cited by 105
Zhou, X., Hsieh, S., & Sun, Y. (2017) · Virtual and Physical Prototyping · doi:10.1080/17452759.2017.1317214 · Cited by 101
Three-dimensional rapid prototyping technologies and key development areas
Kai, C. C. (1994) · Computing & Control Engineering Journal · doi:10.1049/cce:19940407 · Cited by 95
Ilardo, R., & Williams, C. B. (2010) · Rapid Prototyping Journal · doi:10.1108/13552541011034834 · Cited by 92
3D printed polyurethane prosthesis for partial tracheal reconstruction: a pilot animal study
Jung, S. Y., Lee, S. J., Kim, H. Y., Park, H. S., Wang, Z., Kim, H. J., Yoo, J. J., Chung, S. M., & Kim, H. S. (2016) · Biofabrication · doi:10.1088/1758-5090/8/4/045015 · Cited by 88
Singh, A. K., Patil, B., Hoffmann, N., Saltonstall, B., Doddamani, M. R., & Gupta, N. (2018) · JOM · doi:10.1007/s11837-017-2734-7 · Cited by 84
Luo, M., Tian, X., Zhu, W., & Li, D. (2018) · Journal of materials research/Pratt's guide to venture capital sources · doi:10.1557/jmr.2018.131 · Cited by 84
Corcione, C. E., Palumbo, E., Masciullo, A., Montagna, F., & Torricelli, M. C. (2017) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2017.10.011 · Cited by 80
Zaldivar, R. J., McLouth, T. D., Ferrelli, G. L., Patel, D., Hopkins, A. R., & Witkin, D. B. (2018) · Additive manufacturing · doi:10.1016/j.addma.2018.10.022 · Cited by 74
Singh, A. K., Saltonstall, B., Patil, B., Hoffmann, N., Doddamani, M. R., & Gupta, N. (2018) · JOM · doi:10.1007/s11837-017-2731-x · Cited by 70
A study on extruded filament bonding in fused filament fabrication
Costa, A. E., da Silva, A. F., & Carneiro, O. S. (2018) · Rapid Prototyping Journal · doi:10.1108/rpj-03-2018-0062 · Cited by 69
Fang, L., Yan, Y., Agarwal, O., Yao, S., Seppala, J. E., & Kang, S. H. (2020) · Materials · doi:10.3390/ma13194414 · Cited by 61
Enhancing interlayer bonding strength of FDM 3D printing technology by diode laser-assisted system
Sabyrov, N., Abilgaziyev, A., & Ali, M. H. (2020) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-020-05455-y · Cited by 59
Accuracy of medical models made by consumer-grade fused deposition modelling printers
Petropolis, C. J., Kozan, D., & Sigurdson, L. J. (2015) · Plastic Surgery · doi:10.1177/229255031502300201 · Cited by 54
Guessasma, S., Belhabib, S., & Nouri, H. (2019) · Rapid Prototyping Journal · doi:10.1108/rpj-06-2019-0151 · Cited by 44
Biomimetic heterogenous elastic tissue development
Tsai, K. J., Dixon, S., Hale, L. R., Darbyshire, A., Martín, D., & de Mel, A. (2017) · npj Regenerative Medicine · doi:10.1038/s41536-017-0021-4 · Cited by 36
Cited by
Kafle, A., Luis, E., Silwal, R., Pan, H. M., Shrestha, P. L., & Bastola, A. K. (2021) · Polymers · doi:10.3390/polym13183101 · Cited by 587
Taguchi optimization of 3D printed short carbon fiber polyetherketoneketone (CFR PEKK)
Rabinowitz, A., DeSantis, P. M., Basgul, C., Spece, H., & Kurtz, S. M. (2023) · Journal of the Mechanical Behavior of Biomedical Materials · doi:10.1016/j.jmbbm.2023.105981 · Cited by 33
Metadata
- Authors
- Syrlybayev, D., Zharylkassyn, B., Seisekulova, A., Akhmetov, M., Perveen, A., & Talamona, D.
- Venue
- Polymers
- Publisher
- MDPI AG
- Published
- 2021-05-14
- Volume
- 13
- Issue
- 10
- Pages
- 1587
- ISSN
- 2073-4360 (ISSN-L)
- OpenAlex
- W3160937577
- Cited by
- 352
- References
- 85
- FWCI
- 15.23
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.