Evaluation and multi-criteria optimization of surface roughness, deviation from dimensional accuracy and roundness error in drilling CFRP/Ti6Al4 stacks
Open accessThe DOI matches its Crossref record; 37 of the 38 references it cites were found in a registry or an index; 23 of the 62 sources its claims cite were checked for support.
Abstract
In this study, machinability tests were carried out to investigate the effects of control factors (cutting tool geometry, cutting speed, and feed rate) on the surface roughness (Ra), deviation from dimensional accuracy (Da_dev), roundness error (Re) in drilling CFRP/Ti6Al4V mixed metallic stack and to determine the optimum levels of drilling parameters. The effects of each control factor and their interactions on three quality characteristics were analyzed, and their levels were single-objectively optimized for each component material by the Taguchi method. The material has components (CFRP and Ti6Al4V) with essentially different properties (mechanical, physical, machinability). Single-objective optimization has limited usability as the drilling must be performed in one through both layers. Therefore, in an additional step, the optimum levels of the control factors were determined by optimizing multi-objective with the Additive Ratio Assessment (ARAS) method. Higher Ra, Da_dev, and Re values were obtained on the CFRP component compared to the Ti6Al4V component. The CFRP/Ti6Al4V stack should be drilled with a nano fire coated carbide drill (T3) at medium cutting speed and high feed rate to achieve minimum Ra, Da_dev, and Re values in one go.
Overview
CoChat Summary
TL;DR
This study drilled CFRP/Ti6Al4V stacks with three coated carbide drill geometries under dry conditions and optimized surface roughness, dimensional deviation, and roundness error using Taguchi and ARAS. The ARAS optimum was experiment no. 24: T3 (5514-RT100U) drill, 21.0 m/min cutting speed, and 0.078 mm/rev feed rate.
Key findings
- CFRP holes were much rougher and less accurate than Ti6Al4V holes: mean Ra was 0.751 µm for Ti6Al4V vs. 5.560 µm for CFRP (641.67% larger); mean Da_dev was 0.047370 mm vs. 0.749249 mm (1481.70% larger); mean Re was 0.008322 mm vs. 0.075769 mm (810.47% larger).
- Single-objective Taguchi optima differed by component: for Ra_Ti6Al4V, Tg1Vc3f1 (T1, 29 m/min, 0.040 mm/rev); for Ra_CFRP, Tg3Vc3f1 (T3, 29 m/min, 0.040 mm/rev); for Da_dev_Ti6Al4V, Tg2Vc1f1 (T2, 15 m/min, 0.040 mm/rev); for Da_dev_CFRP, Tg3Vc3f1; for Re_Ti6Al4V, Tg1Vc1f2 (T1, 15 m/min, 0.056 mm/rev); for Re_CFRP, Tg3Vc1f3 (T3, 15 m/min, 0.078 mm/rev).
- Multi-objective ARAS ranked experiment no. 24 first, with T3 (5514-RT100U), Vc=21.0 m/min, f=0.078 mm/rev, at 77.16% closeness to optimal; experiment no. 3 ranked last at 33.69%.
- ANOVA for Ki showed the largest contributions from Tg*Vc (21.43%) and feed rate (21.08%); the text also states feed rate was the most effective drilling parameter on Ki.
Methods
- Dry drilling tests were performed on a CFRP/Ti6Al4V stack consisting of 5 mm Ti6Al4V and 5 mm CFRP (64% fiber, 36% resin), using the Ti6Al4V → CFRP strategy, 6 mm diameter coated carbide drills T1/T2/T3 with 140° point angle, and a new drill for each hole.
- Taguchi L27(3^3) design was used with control factors: cutting tool geometry (T1, T2, T3), cutting speed (15, 21, 29 m/min), and feed rate (0.040, 0.056, 0.0784 mm/rev); S/N ratios used “smaller is better,” and ANOVA was at 95% confidence.
- Ra was measured with a Mitutoyo Surftest 201 (5 measurements per hole, λc=2.5 mm); Da_dev and Re were measured on a CMM at 1.5, 3, 6.5, and 8 mm depths using 10 points at 36° intervals, with 6 measurements per component; ARAS weights were derived from Taguchi S/N response differences.
Limitations
- The paper states future work should include cooling methods, tool wear, and material removal mechanics, which were not part of this study.
- Evident from the text: drilling was performed without coolant, each hole used a new drill, and only one hole was drilled per condition, so progressive tool wear and thermal effects were not evaluated; the authors also note the total drilled thickness did not exceed 10 mm and chip volume was very small.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
9 Valid · 2 Not valid · 12 Not checked · 64 Own results and interpretations
At least one cited source doesn’t support this claim or points to a different paper, and none confirmed it — see the verdicts below.
In the paper
“Because the effect of various cutting conditions on hole damage, dimensional hole accuracy, and hole quality when machining CFRP/Ti alloy stacks has been little studied [7-11].”
What the sources say
- Disputedcites [7] [7] Kolesnyk, V., Peterka, J., Kuruc, M., Šimna, V., Morav č íková, J., Vopát, T. and Lisovenko, D.: Experimental study of drilling temperature, geometrical errors and thermal expansion of drill on hole accuracy when drilling CFRP/Ti alloy stacks, Materials, Vol. 13, No. 14, pp. 3232, 2020. - sourceExperimental — accuracy not yet measured
The Introduction states that the effects of cutting parameters, tool geometry, and tool wear on hole quality in CFRP/Ti stacks are well studied. It identifies a narrower gap: how drilling temperature and resulting tool thermal expansion affect hole accuracy. The claim turns that specific gap into a broad assertion that cutting conditions and their effects on hole damage, accuracy, and quality have been little studied. (LLM, conf=0.87)
Checked by a reasoning model — may be wrong.
- Disputedcites [8] [8] Xu, J. and El Mansori, M.: Experimental study on drilling mechanisms and strategies of hybrid CFRP/Ti stacks, Compos. Struct., Vol. 157, pp. 461-482, 2016. - sourceExperimental — accuracy not yet measured
The Introduction says a large amount of experimental work on CFRP/Ti drilling had already been performed and identifies the effects of cutting parameters on hole quality as a research focus. Section 3.4 also says previous studies had shown that cutting speed and feed rate affect hole quality. The paper describes cutting-sequence effects and machinability classification—not the broadly stated effects of cutting conditions on hole quality and damage—as rarely reported. Page numbers are not available in our copy. (LLM, conf=0.86)
Checked by a reasoning model — may be wrong.
- Not matchedcites [9] [9] Ekici, E. and Motorcu A. R.: CFRP/Ti6Al4V metalik y ı ğ ı n ı n delinmesinde kesme parametreleri ve delme stratejisinin yüzey pürüzlülü ğ üne etkisi, in: Proceedings of the 9th International Congress On Engineering, Architecture and Design , İ stanbul, Türkiye, 14-16.05.2022, pp.190-197. -
Its entry has no title and year that we can search by.
- Not checked — no full text of the sourcecites [10] [10] Xu, J., Zhou, L., Chen, M. and Ren, F.: Experimental study on mechanical drilling of carbon/epoxy composite-Ti6Al4V stacks, Mater. Manuf. Process. Vol. 34, No.7, pp.715-725, 2019. - source
- Could not verifycites [11] [11] Xu, J. and El Mansori, M.: Experimental studies on the cutting characteristics of hybrid CFRP/Ti 12. stacks, Procedia. Manuf., Vol. 5, pp. 270-281, 2016. - sourceExperimental — accuracy not yet measured
The Introduction (p. 3) says prior work has covered machined surface quality and identifies a gap in understanding orthogonal cutting. The paper does not address whether the effects of cutting conditions on hole damage, dimensional hole accuracy, and hole quality have been little studied; searches for those hole-specific terms found no such passage. (LLM, conf=0.75)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Disputed
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Lower roundness error values were obtained at the lowest cutting speed when drilling through the metallic stack in one go [7, 8, 10, 17, 18, 20, 21, 24, 42].”
What the sources say
- Could not verifycites [7] [7] Kolesnyk, V., Peterka, J., Kuruc, M., Šimna, V., Morav č íková, J., Vopát, T. and Lisovenko, D.: Experimental study of drilling temperature, geometrical errors and thermal expansion of drill on hole accuracy when drilling CFRP/Ti alloy stacks, Materials, Vol. 13, No. 14, pp. 3232, 2020. - sourceExperimental — accuracy not yet measured
Section 3.2 (page unavailable) reports roundness changes in the CFRP layer under different drilling-delay conditions, but says that effect was not observed in the Ti-alloy layer. The passages on cutting speed and roundness do not establish that the lowest speed produced lower roundness error when drilling a metallic stack in one go. (LLM, conf=0.70)
- Partly supportedcites [8] [8] Xu, J. and El Mansori, M.: Experimental study on drilling mechanisms and strategies of hybrid CFRP/Ti stacks, Compos. Struct., Vol. 157, pp. 461-482, 2016. - sourceExperimental — accuracy not yet measured
Section 3.4.2 recommends low cutting speed together with low feed rate to minimize roundness error when drilling hybrid CFRP/Ti stacks, and the Conclusions describe one-shot drilling. But Section 3.4.2 says the effect of cutting speed varies across conditions; it does not establish that the lowest speed consistently produced the lowest roundness error. The studied stack also contains both CFRP and titanium, rather than being wholly metallic. (LLM, conf=0.85)
- Not checked — no full text of the sourcecites [10] [10] Xu, J., Zhou, L., Chen, M. and Ren, F.: Experimental study on mechanical drilling of carbon/epoxy composite-Ti6Al4V stacks, Mater. Manuf. Process. Vol. 34, No.7, pp.715-725, 2019. - source
- Not checked — no full text of the sourcecites [17] [17] Xu, J., Ji, M., Chen, M. and El Mansori, M.: Experimental investigation on drilling machinability and hole quality of CFRP/Ti6Al4V stacks under different cooling conditions, Int. J. Adv. Manuf., Vol.109, No. 5, pp. 1527-1539, 2020. - source
- Not checked — no full text of the sourcecites [18] [18] Xu, J., Ji, M., Chen, M. and Ren, F.: Investigation of minimum quantity lubrication effects in drilling CFRP/Ti6Al4V stacks, Mater. Manuf. Process., Vol. 34, No.12, pp.1401-1410, 2019. - source
- Not checked — no full text of the sourcecites [20] [20] An, Q., Dang, J., Li, J., Wang, C. and Chen, M.: Investigation on the cutting responses of CFRP/Ti stacks: With special emphasis on the effects of drilling sequences, Compos. Struct., Vol. 253, pp.112794, 2020. - source
- Not checked — no full text of the sourcecites [21] [21] Jia, Z.Y., Zhang, C., Wang, F.J., Fu, R. and Chen, C.: Multi-margin drill structure for improving hole quality and dimensional consistency in drilling Ti/CFRP stacks, J. Mater. Process. Technol., Vol. 276, pp. 116405, 2020. - source
- Could not verifycites [24] [24] Alonso, U., Calamaz, M., Girot, F. and Iriondo, E.: Influence of flute number and stepped bit geometry when drilling CFRP/Ti6Al4V stacks. J. Manuf. Process. Vol. 39, pp. 356-370, 2019. - sourceExperimental — accuracy not yet measured
Section 2.3, Table 4 lists the same cutting speed (15 m/min) for all tested drill geometries, so it provides no lowest-speed comparison. Section 3.3 describes hole diameter, surface roughness, burrs and delamination, but the searched passages on roundness and circularity do not report the claimed roundness-error result for drilling the stack in one go. (LLM, conf=0.76)
- Not checked — no full text of the sourcecites [42] [42] Kumar, D., Gururaja, S. and Jawahir, I.S.: Machinability and surface integrity of adhesively bonded Ti/CFRP/Ti hybrid composite laminates under dry and cryogenic conditions, J. Manuf. Process., Vol. 58, pp. 1075-1087, 2020. - source
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Could not verify
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Again, a lower deviation from dimensional accuracy values was obtained for both CFRP, and Ti6Al4V components at low feed rate drilling of CFRP/Ti6Al4V mixed metallic stack [7, 8, 10, 17, 18, 20, 21, 24, 42].”
What the sources say
- Partly supportedcites [7] [7] Kolesnyk, V., Peterka, J., Kuruc, M., Šimna, V., Morav č íková, J., Vopát, T. and Lisovenko, D.: Experimental study of drilling temperature, geometrical errors and thermal expansion of drill on hole accuracy when drilling CFRP/Ti alloy stacks, Materials, Vol. 13, No. 14, pp. 3232, 2020. - sourceExperimental — accuracy not yet measured
Section 3.2 (page not available) links some large CFRP hole-diameter deviations to high feed, but also reports large deviations at low feed and attributes deviations to drilling temperature and other factors. It does not establish that low feed reduces deviations in both layers; the largest reported tolerance field in the titanium layer occurred at a low feed. Moreover, the tested alloy was Ti-2.5Al-2Mn, not Ti6Al4V (Materials and Methods, §2.1; page not available). (LLM, conf=0.88)
- Supportedcites [8] [8] Xu, J. and El Mansori, M.: Experimental study on drilling mechanisms and strategies of hybrid CFRP/Ti stacks, Compos. Struct., Vol. 157, pp. 461-482, 2016. - source
Section 3.4.2 reports that low feed rates produce tighter hole diameters and lower roundness error in both CFRP and Ti holes. It also notes that low cutting speed and the Ti→CFRP cutting sequence improve dimensional results, but these additional conditions do not negate the reported feed-rate effect. (LLM, conf=0.91)
- Not checked — no full text of the sourcecites [10] [10] Xu, J., Zhou, L., Chen, M. and Ren, F.: Experimental study on mechanical drilling of carbon/epoxy composite-Ti6Al4V stacks, Mater. Manuf. Process. Vol. 34, No.7, pp.715-725, 2019. - source
- Not checked — no full text of the sourcecites [17] [17] Xu, J., Ji, M., Chen, M. and El Mansori, M.: Experimental investigation on drilling machinability and hole quality of CFRP/Ti6Al4V stacks under different cooling conditions, Int. J. Adv. Manuf., Vol.109, No. 5, pp. 1527-1539, 2020. - source
- Not checked — no full text of the sourcecites [18] [18] Xu, J., Ji, M., Chen, M. and Ren, F.: Investigation of minimum quantity lubrication effects in drilling CFRP/Ti6Al4V stacks, Mater. Manuf. Process., Vol. 34, No.12, pp.1401-1410, 2019. - source
- Not checked — no full text of the sourcecites [20] [20] An, Q., Dang, J., Li, J., Wang, C. and Chen, M.: Investigation on the cutting responses of CFRP/Ti stacks: With special emphasis on the effects of drilling sequences, Compos. Struct., Vol. 253, pp.112794, 2020. - source
- Not checked — no full text of the sourcecites [21] [21] Jia, Z.Y., Zhang, C., Wang, F.J., Fu, R. and Chen, C.: Multi-margin drill structure for improving hole quality and dimensional consistency in drilling Ti/CFRP stacks, J. Mater. Process. Technol., Vol. 276, pp. 116405, 2020. - source
- Partly supportedcites [24] [24] Alonso, U., Calamaz, M., Girot, F. and Iriondo, E.: Influence of flute number and stepped bit geometry when drilling CFRP/Ti6Al4V stacks. J. Manuf. Process. Vol. 39, pp. 356-370, 2019. - sourceExperimental — accuracy not yet measured
Section 2.3 (page not provided) says lower feeds are advantageous for CFRP and moderate feeds can give good results in both materials, but it also says higher feeds improve titanium hole quality. Section 3.3.1 (page not provided) measures hole diameters in both layers and discusses variation by drill geometry and hole number; it does not establish that low feed rates reduced dimensional deviation in both layers. (LLM, conf=0.83)
- Not checked — no full text of the sourcecites [42] [42] Kumar, D., Gururaja, S. and Jawahir, I.S.: Machinability and surface integrity of adhesively bonded Ti/CFRP/Ti hybrid composite laminates under dry and cryogenic conditions, J. Manuf. Process., Vol. 58, pp. 1075-1087, 2020. - source
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“In the drilling of CFRP, the roundness error values of the holes Re were 810.47% larger on average than the Ti6Al4V alloy [6-9, 17, 19, 20, 23, 38].”
What the sources say
- Not matchedcites [6] [6] Prasanth, R., Prabukarthi, A., Kumar, M.S., Krishnaraj, V. and Rajamani, R.: identification of drill position in CFRP/Titanium alloy stacks using acoustic emission signals, in: Proceedings of the International Conference on Advances in Materials, Manufacturing and Applications (AMMA 2015) , 09-11.04.2015, Trichy, pp.11741181. -
Its entry has no title and year that we can search by.
- Partly supportedcites [7] [7] Kolesnyk, V., Peterka, J., Kuruc, M., Šimna, V., Morav č íková, J., Vopát, T. and Lisovenko, D.: Experimental study of drilling temperature, geometrical errors and thermal expansion of drill on hole accuracy when drilling CFRP/Ti alloy stacks, Materials, Vol. 13, No. 14, pp. 3232, 2020. - sourceExperimental — accuracy not yet measured
Section 3.2 (page unavailable) reports that hole roundness increased in CFRP under HDM conditions, while that effect was not observed in the titanium alloy. It does not report an average roundness error 810.47% larger in CFRP. Section 2.1 (page unavailable) identifies the alloy studied as Ti-2.5Al-2Mn, not Ti6Al4V. (LLM, conf=0.86)
- Could not verifycites [8] [8] Xu, J. and El Mansori, M.: Experimental study on drilling mechanisms and strategies of hybrid CFRP/Ti stacks, Compos. Struct., Vol. 157, pp. 461-482, 2016. - sourceExperimental — accuracy not yet measured
Section 3.4.2 (page unavailable) reports roundness errors for both CFRP and Ti holes, including values of about 5–10 μm at low feed rates. It does not give an average CFRP-to-Ti roundness-error comparison or the claimed 810.47% difference; searches for that percentage and for a comparative average found no supporting passage. (LLM, conf=0.72)
- Not matchedcites [9] [9] Ekici, E. and Motorcu A. R.: CFRP/Ti6Al4V metalik y ı ğ ı n ı n delinmesinde kesme parametreleri ve delme stratejisinin yüzey pürüzlülü ğ üne etkisi, in: Proceedings of the 9th International Congress On Engineering, Architecture and Design , İ stanbul, Türkiye, 14-16.05.2022, pp.190-197. -
Its entry has no title and year that we can search by.
- Not checked — no full text of the sourcecites [17] [17] Xu, J., Ji, M., Chen, M. and El Mansori, M.: Experimental investigation on drilling machinability and hole quality of CFRP/Ti6Al4V stacks under different cooling conditions, Int. J. Adv. Manuf., Vol.109, No. 5, pp. 1527-1539, 2020. - source
- Not matchedcites [19] [19] Akhil, P.V., Krishnaraj, V., Prabukarthi, A., Kumar, M.S. and Elangovan, S.: Study of tool condition monitoring during drilling of CFRP/Ti stacks under dry and wet conditions, in: Proceedings of the International Conference on Advances in Materials, Manufacturing and Applications (AMMA 2015) , 09-11.04.2015, Trichy, pp.839-834. -
Its entry has no title and year that we can search by.
- Not checked — no full text of the sourcecites [20] [20] An, Q., Dang, J., Li, J., Wang, C. and Chen, M.: Investigation on the cutting responses of CFRP/Ti stacks: With special emphasis on the effects of drilling sequences, Compos. Struct., Vol. 253, pp.112794, 2020. - source
- Could not verifycites [23] [23] Xu, J., El Mansori, M., Chen, M. and Ren, F.: Orthogonal cutting mechanisms of CFRP/Ti6Al4V stacks, Int. J. Adv. Manuf., Vol. 103, No. 9-12, pp. 3831-3851, 2019. - sourceExperimental — accuracy not yet measured
The Introduction discusses the difficulty of drilling CFRP/Ti6Al4V stacks, but gives no roundness-error comparison. Section 3.5 compares surface roughness after orthogonal cutting, a different measure; searches for roundness error and 810.47% found no supporting passage in our copy. Page numbers were not available. (LLM, conf=0.76)
- Not checked — no full text of the sourcecites [38] [38] Y ı ld ı r ı m, B.F.: Çok kriterli karar verme problemlerinde ARAS yöntemi, Kafkas Üniversitesi İ ktisadi ve İ dari Bilimler Fakültesi Dergisi, Vol. 6, No. 9, pp. 285-296, 2015. - source
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Not matched
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“On the other hand, unlike the CFRP layers, the average surface roughness values of the Ti layer remain relatively more consistent [8, 10, 12, 18, 24, 39, 40].”
What the sources say
- Supportedcites [8] [8] Xu, J. and El Mansori, M.: Experimental study on drilling mechanisms and strategies of hybrid CFRP/Ti stacks, Compos. Struct., Vol. 157, pp. 461-482, 2016. - source
Section 3.4.1 reports narrower ranges of average roughness (Ra) for Ti than for CFRP under the same CFRP→Ti drilling sequence. It also reports a narrower Ti range under the Ti→CFRP sequence, supporting the relative comparison. Page numbers are not supplied in our copy. (LLM, conf=0.88)
- Not checked — no full text of the sourcecites [10] [10] Xu, J., Zhou, L., Chen, M. and Ren, F.: Experimental study on mechanical drilling of carbon/epoxy composite-Ti6Al4V stacks, Mater. Manuf. Process. Vol. 34, No.7, pp.715-725, 2019. - source
- Supportedcites [12] [12] Kim, D., Swan, S.R., He, B., Khominich, V., Bell, E., Lee, S.W. and Kim, T.G.: A study on the machinability of advanced arc PVD AlCrN-coated tungsten carbide tools in drilling of CFRP/titanium alloy stacks, Carbon. Lett., Vol. 31, No. 3, pp. 497-507, 2021. - source
Section 3.3.3 (Hole quality parameters) states that, unlike the CFRP layers, the Ti layer’s average Ra values were relatively consistent over 144 holes. This directly supports the attributed comparison within the study’s drilling conditions. (LLM, conf=0.95)
- Not checked — no full text of the sourcecites [18] [18] Xu, J., Ji, M., Chen, M. and Ren, F.: Investigation of minimum quantity lubrication effects in drilling CFRP/Ti6Al4V stacks, Mater. Manuf. Process., Vol. 34, No.12, pp.1401-1410, 2019. - source
- Could not verifycites [24] [24] Alonso, U., Calamaz, M., Girot, F. and Iriondo, E.: Influence of flute number and stepped bit geometry when drilling CFRP/Ti6Al4V stacks. J. Manuf. Process. Vol. 39, pp. 356-370, 2019. - sourceExperimental — accuracy not yet measured
Section 3.3 says the paper compares surface roughness, but the passages retrieved for 'average surface roughness' and related terms give no roughness values or comparison of their consistency in CFRP and Ti. Section 3.3.1 discusses hole diameter instead, which cannot establish the claimed roughness pattern. (LLM, conf=0.72)
- Not checked — no full text of the sourcecites [39] [39] Ji, M., Xu, J., Chen, M. and Mansori, M.E.: Effects of different cooling methods on the specific energy consumption when drilling CFRP/Ti6Al4V stacks, Procedia Manuf, Vol. 43, pp. 95-102, 2020. - source
- Partly supportedcites [40] [40] Xu, J., El Mansori, M., Voisin, J., Chen, M. and Ren, F.: On the interpretation of drilling CFRP/Ti6Al4V stacks using the orthogonal cutting method: Chip removal mode and subsurface damage formation, J. Manuf. Process., Vol. 44, pp. 435-447, 2019. - sourceExperimental — accuracy not yet measured
Section 3.3.3 (page unavailable) says Ti hole surfaces are smoother than CFRP surfaces, which supports the comparison in general. It does not report average roughness values or establish that Ti roughness remains more consistent; it also says higher feed rates intensify marks and grooves on Ti surfaces. (LLM, conf=0.82)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
42 more claims
Create a free account to see all 87 claims and every source verdict.
- It may state two separate claims as one. 30
- Probably not a substantial claim. 14
- The quote only partly states this claim. 1
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
§ 4. CONCLUSIONS
“Optimal machining conditions were determined as T3(5514-RT100U) coded tool, Vc =15m/min cutting speed, and f =0.078mm/rev feed rate to obtain minimum Ra surface roughness value in CFRP component.”
§ 4. CONCLUSIONS
“Optimal machining conditions were determined as T3(5514-RT100U) coded tool, Vc =29m/min cutting speed, and f =0.040mm/rev feed rate to obtain minimum Ra surface roughness value in CFRP component.”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Deviation from Dimensional Accuracy ( Da\_dev )
“Da\_dev values were measured in 0.0277366-0.047370 mm for Ti6Al4V Ti alloy”
§ Surface Roughness ( Ra )
“| 22 | T3 (5514-RT100U) | 21 | 0.040 | 0.475 5.095 | 0.142162”
Citations
Cites
Hole quality assessment following drilling of metallic-composite stacks
Shyha, I. S., Soo, S. L., Aspinwall, D. K., Bradley, S., Perry, R., Harden, P., & Dawson, S. (2011) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2011.04.007 · Cited by 192 · cited 1×
“analyzed hole quality/integrity after drilling titanium/CFRP/aluminum stacks under flood coolant and spray mist environments [29].”
BackgroundExperimental study on drilling mechanisms and strategies of hybrid CFRP/Ti stacks
Xu, J., & El Mansori, M. (2016) · Composite Structures · doi:10.1016/j.compstruct.2016.07.025 · Cited by 162 · cited 9×
“In contrast, the CFRP/Ti drilling strategy only reduced induced delamination [8].”
BackgroundMethodResultInfluentialXu, J., Li, C., Chen, M., Mansori, M. E., & Davim, J. P. (2019) · Composite Structures · doi:10.1016/j.compstruct.2019.111708 · Cited by 128 · cited 1×
“, it was determined that drilling from Ti to CFRP leads to higher shear temperatures of the composite, decreases the stacking thrust forces, improves the composite surface morphologies, and reduces the exit titanium burr heights [22].”
BackgroundIsbilir, O., & Ghassemieh, E. (2013) · Machining Science and Technology · doi:10.1080/10910344.2013.806098 · Cited by 107 · cited 6×
“Considering these values, the Ra values of CFRP are many times higher than Ti6Al4V [13].”
BackgroundResultInfluentialAn, Q., Dang, J., Li, J., Wang, C., & Chen, M. (2020) · Composite Structures · doi:10.1016/j.compstruct.2020.112794 · Cited by 95 · cited 6×
“It is understood from Table 3 that the mean deviation from dimensional accuracy calculated for CFRP is higher than the mean deviation from dimensional accuracy calculated for Ti6Al4V Ti alloy [7, 8, 10, 18-21, 42].”
BackgroundMethodInfluentialExperimental study on mechanical drilling of carbon/epoxy composite-Ti6Al4V stacks
Xu, J., Zhou, L., Chen, M., & Ren, F. (2019) · Materials and Manufacturing Processes · doi:10.1080/10426914.2019.1594275 · Cited by 80
Investigation of minimum quantity lubrication effects in drilling CFRP/Ti6Al4V stacks
Xu, J., Ji, M., Chen, M., & Ren, F. (2019) · Materials and Manufacturing Processes · doi:10.1080/10426914.2019.1661431 · Cited by 73
Wei, Y., An, Q., Ming, W., & Chen, M. (2016) · Advances in Mechanical Engineering · doi:10.1177/1687814016670281 · Cited by 67 · cited 2×
“In the ARAS method, there is a row consisting of the optimal values of each criterion in the initial decision matrix [32-38].”
MethodXu, J., Ji, M., Chen, M., & El Mansori, M. (2020) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-020-05742-8 · Cited by 63 · cited 4×
“47% larger on average than the Ti6Al4V alloy [6-9, 17, 19, 20, 23, 38].”
BackgroundInfluentialÇOK KRİTERLİ KARAR VERME PROBLEMLERİNDE ARAS YÖNTEMİ
Yıldırım, B. F. (2015) · Kafkas Üniversitesi İktisadi ve İdari Bilimler Fakültesi Dergisi · doi:10.18025/kauiibf.65151 · Cited by 59 · cited 9×
“This equation xij represents the performance value of the ith alternative in the jth criterion and x0j the optimal value of the jth criterion [38].”
BackgroundMethodInfluential
Research works printed but not linked: 8
- [3] Xu, J., An, Q., Ming, W. and Chen, M.: A study on the effects of cutting-sequence strategies in drilling CFRP/Ti, in: Proceedings of The Advances in Abrasive Technology XX: 20th International Symposium on Advances in Abrasive Technology , 03-03.12.2017, Okinawa, pp.364-369. -
- [4] Motorcu, A.R. and Ekici, E.: CFRP/Ti6Al4V y ı ğ ı nlar ı n kademeli matkapla delinmesinde CFRP'de minimum delaminasyon faktörü için kontrol faktörlerinin optimizasyonu, in: Proceedings of The 5. International Conference on Material Science and Technology (IMSTEC 2020) , 16-18.10.2020, Nev ş ehir, pp.133-139. -
- [5] Motorcu, A.R. and Ekici, E.: CFRP/Ti6Al4V y ı ğ ı n ı n farkl ı geometrili tak ı mlarla delinmesinde minimum delaminasyon olu ş umu için proses parametrelerinin çok amaçl ı optimizasyonu . in: Proceedings of The 5th International Congress On Engineering and Technology Management , 2425.04.2021, İ stanbul, pp.219-231. -
- [6] Prasanth, R., Prabukarthi, A., Kumar, M.S., Krishnaraj, V. and Rajamani, R.: identification of drill position in CFRP/Titanium alloy stacks using acoustic emission signals, in: Proceedings of the International Conference on Advances in Materials, Manufacturing and Applications (AMMA 2015) , 09-11.04.2015, Trichy, pp.11741181. -
- [9] Ekici, E. and Motorcu A. R.: CFRP/Ti6Al4V metalik y ı ğ ı n ı n delinmesinde kesme parametreleri ve delme stratejisinin yüzey pürüzlülü ğ üne etkisi, in: Proceedings of the 9th International Congress On Engineering, Architecture and Design , İ stanbul, Türkiye, 14-16.05.2022, pp.190-197. -
- [14] Zhang, C., Jia, Z., Wang, F., Zhang, B., Bi, G. and Yin, J.: Design of A New One-Shot Tool with Double Margins Structure in Drilling Titanium/Composite Stacks, in: Proceedings of the 21st International Conference on Composite Materials , 20-25.08.2017, Xi'an, pp.1-8. -
- [19] Akhil, P.V., Krishnaraj, V., Prabukarthi, A., Kumar, M.S. and Elangovan, S.: Study of tool condition monitoring during drilling of CFRP/Ti stacks under dry and wet conditions, in: Proceedings of the International Conference on Advances in Materials, Manufacturing and Applications (AMMA 2015) , 09-11.04.2015, Trichy, pp.839-834. -
- [37] Paramasivam, S.S.S.S., Kumaran, D. and Natarajan, H.: Taguchi Additive Ratio Assessment (ARAS) method in multi-criteria decision making: A case study for treated drill tools performance. Int. J. Mod. Manuf., Vol.12, No.1, pp.114-124, 2020. -
Cited by
ABBED, K., Kribes, N., Yallese, M. A., Chihaoui, S., & Boutabba, S. (2023) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-023-11775-6 · Cited by 25
“[30] evaluated and optimized the surface roughness, deviation from dimensional accuracy, and roundness error when drilling CFRP/Ti6Al4.”
MethodFedai, Y. (2023) · Processes · doi:10.3390/pr11102872 · Cited by 20
Yin, J., Wang, X., Zhou, Q., et al. (2025) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2025.03.069 · Cited by 19
Chtioui, A., Ouballouch, A., & Mouchtachi, A. (2024) · FME Transaction · doi:10.5937/fme2404616c · Cited by 6
Pramod, R., Veeresh, K., & Basavarajappa, S. (2024) · FME Transaction · doi:10.5937/fme2404573p · Cited by 6
Mathiyazhagan, V., & Meena, A. (2024) · Proceedings of the Institution of Mechanical Engineers Part B Journal of Engineering Manufacture · doi:10.1177/09544054241249780 · Cited by 3
Detection and evaluation of hole making delamination damage in CFRP based on RGHT
Nie, P. C., Peng, X., Yang, C., et al. (2024) · Journal of Reinforced Plastics and Composites · doi:10.1177/07316844241240514 · Cited by 2
“1,2 Typically, CFRP components are formed and subsequently assembled with other fasteners using rivets or bolted connections, making holemaking the most prevalent secondary machining method.”
Baraheni, M., Karkhaneh, M., Bagheri, E. A., et al. (2026) · Engineering Applications of Artificial Intelligence · doi:10.1016/j.engappai.2026.113732 · Cited by 2
Sztankovics, I., & Rodić, D. (2026) · FME Transaction · doi:10.5937/fme2601039s · Cited by 1
Karolczak, P., & Kowalski, M. (2024) · FME Transaction · doi:10.5937/fme2404590k
AbouHawa, M., Eisa, A., Fattouh, M., et al. (2026) · REVIEWS ON ADVANCED MATERIALS SCIENCE · doi:10.1515/rams-2025-0256
“The dimensional deviation ( D dev ) is de fi ned as the absolute value of the di ff erence between the desired diameter value (software diameter) and the measured diameter value [47] as detailed in Eq.”
Chtioui, A., Ouballouch, A., & Mouchtachi, A. (2026) · FME Transaction · doi:10.5937/fme2603498c
“Therefore the quality of machined parts is adversely affected, resulting in limitation in surface roughness, dimensional accuracy and geometric tolerances [18,19], which are critical for components with stringent functional requirements.”
Metadata
- Authors
- Motorcu, A., & Ekici, E.
- Affiliations
- Çanakkale Onsekiz Mart Üniversitesi (TR)
- ORCID
- Motorcu, Ali
- Venue
- FME Transactions
- Published
- 2022
- Volume
- 50
- Issue
- 3
- Pages
- 441-460
- ISSN
- 1451-2092 (ISSN-L)
- 2406-128X
- OpenAlex
- W4297923018
- Cited by
- 12
- References
- 38
- Citations by year
- 2026: 4 · 2025: 1 · 2024: 5 · 2023: 2
- FWCI
- 0.75
- Type
- journal article
- Language
- en
- Open access
- diamond
- doi.org
- Locations
- FME Transaction (publishedVersion, cc-by)
- Çanakkale Onsekiz Mart University AVESIS (submittedVersion)
- Çanakkale Onsekiz Mart University Institutional Repository (submittedVersion, cc-by-nc-nd)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Funders
- Çanakkale Onsekiz Mart Üniversitesi
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Advanced machining processes and optimization
- Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Advanced Machining and Optimization Techniques
- Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Engineering Technology and Methodologies
- Keywords
- drilling, carbon fiber reinforced polymer, titanium alloys, machinability, surface roughness, dimensional accuracy, roundness error, multi-objective optimization, Taguchi method, ARAS method, tool geometry, cutting speed, feed rate, hybrid composites
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-09-28, under version 3 of the claim definition (prompt extract-v3).
A second model labelled each claim on 2026-09-28 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.