Student or educator? Sign up with your school email and get 6 months of Pro free.
CoChat

The DOI matches its Crossref record; 36 of the 38 references it cites were found in a registry or an index; 23 of the 62 sources its claims cite were checked for support.

Evaluation and multi-criteria optimization of surface roughness, deviation from dimensional accuracy and roundness error in drilling CFRP/Ti6Al4 stacks

Open access
Motorcu, Ali, Ekici, Ergün · 2022 · FME Transactions

Abstract

In this study, machinability tests were carried out to investigate the effects of control factors (cutting tool geometry, cutting speed, and feed rate) on the surface roughness (Ra), deviation from dimensional accuracy (Da_dev), roundness error (Re) in drilling CFRP/Ti6Al4V mixed metallic stack and to determine the optimum levels of drilling parameters. The effects of each control factor and their interactions on three quality characteristics were analyzed, and their levels were single-objectively optimized for each component material by the Taguchi method. The material has components (CFRP and Ti6Al4V) with essentially different properties (mechanical, physical, machinability). Single-objective optimization has limited usability as the drilling must be performed in one through both layers. Therefore, in an additional step, the optimum levels of the control factors were determined by optimizing multi-objective with the Additive Ratio Assessment (ARAS) method. Higher Ra, Da_dev, and Re values were obtained on the CFRP component compared to the Ti6Al4V component. The CFRP/Ti6Al4V stack should be drilled with a nano fire coated carbide drill (T3) at medium cutting speed and high feed rate to achieve minimum Ra, Da_dev, and Re values in one go.

Overview

CoChat Summary

TL;DR

This study drilled CFRP/Ti6Al4V stacks with three coated carbide drill geometries under dry conditions and optimized surface roughness, dimensional deviation, and roundness error using Taguchi and ARAS. The ARAS optimum was experiment no. 24: T3 (5514-RT100U) drill, 21.0 m/min cutting speed, and 0.078 mm/rev feed rate.

Key findings

  • CFRP holes were much rougher and less accurate than Ti6Al4V holes: mean Ra was 0.751 µm for Ti6Al4V vs. 5.560 µm for CFRP (641.67% larger); mean Da_dev was 0.047370 mm vs. 0.749249 mm (1481.70% larger); mean Re was 0.008322 mm vs. 0.075769 mm (810.47% larger).
  • Single-objective Taguchi optima differed by component: for Ra_Ti6Al4V, Tg1Vc3f1 (T1, 29 m/min, 0.040 mm/rev); for Ra_CFRP, Tg3Vc3f1 (T3, 29 m/min, 0.040 mm/rev); for Da_dev_Ti6Al4V, Tg2Vc1f1 (T2, 15 m/min, 0.040 mm/rev); for Da_dev_CFRP, Tg3Vc3f1; for Re_Ti6Al4V, Tg1Vc1f2 (T1, 15 m/min, 0.056 mm/rev); for Re_CFRP, Tg3Vc1f3 (T3, 15 m/min, 0.078 mm/rev).
  • Multi-objective ARAS ranked experiment no. 24 first, with T3 (5514-RT100U), Vc=21.0 m/min, f=0.078 mm/rev, at 77.16% closeness to optimal; experiment no. 3 ranked last at 33.69%.
  • ANOVA for Ki showed the largest contributions from Tg*Vc (21.43%) and feed rate (21.08%); the text also states feed rate was the most effective drilling parameter on Ki.

Methods

  • Dry drilling tests were performed on a CFRP/Ti6Al4V stack consisting of 5 mm Ti6Al4V and 5 mm CFRP (64% fiber, 36% resin), using the Ti6Al4V → CFRP strategy, 6 mm diameter coated carbide drills T1/T2/T3 with 140° point angle, and a new drill for each hole.
  • Taguchi L27(3^3) design was used with control factors: cutting tool geometry (T1, T2, T3), cutting speed (15, 21, 29 m/min), and feed rate (0.040, 0.056, 0.0784 mm/rev); S/N ratios used “smaller is better,” and ANOVA was at 95% confidence.
  • Ra was measured with a Mitutoyo Surftest 201 (5 measurements per hole, λc=2.5 mm); Da_dev and Re were measured on a CMM at 1.5, 3, 6.5, and 8 mm depths using 10 points at 36° intervals, with 6 measurements per component; ARAS weights were derived from Taguchi S/N response differences.

Limitations

  • The paper states future work should include cooling methods, tool wear, and material removal mechanics, which were not part of this study.
  • Evident from the text: drilling was performed without coolant, each hole used a new drill, and only one hole was drilled per condition, so progressive tool wear and thermal effects were not evaluated; the authors also note the total drilled thickness did not exceed 10 mm and chip volume was very small.

Model-written summary. Check it against the paper before relying on it.

Integrity signals

Registry

Crossref · 10.5937/fme2203441m

Cites

36 of 36 references verified0 citation errors · 0 not checkable

Statistics

Nothing to recompute.

Verification

Claims the paper makes

9 Valid · 2 Not valid · 12 Not checked · 64 Own results and interpretations

42 more claims

Create a free account to see all 87 claims and every source verdict.

See all claims — free account
  • It may state two separate claims as one. 30
  • Probably not a substantial claim. 14
  • The quote only partly states this claim. 1

Create a free account to see these claims.

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

Each contradiction between two passages listed here was confirmed by an independent check.

2 of 2

Citations

Cites

Research works printed but not linked: 8

  1. Xu, J., An, Q., Ming, W. and Chen, M.: A study on the effects of cutting-sequence strategies in drilling CFRP/Ti, in: Proceedings of The Advances in Abrasive Technology XX: 20th International Symposium on Advances in Abrasive Technology, 03-03.12.2017, Okinawa, pp.364-369;
  2. Motorcu, A.R. and Ekici, E.: CFRP/Ti6Al4V yığınların kademeli matkapla delinmesinde CFRP'de minimum delaminasyon faktörü için kontrol faktörlerinin optimizasyonu, in: Proceedings of The 5. International Conference on Material Science and Technology (IMSTEC 2020), 16-18.10.2020, Nevşehir, pp.133-139;
  3. Motorcu, A.R. and Ekici, E.: CFRP/Ti6Al4V yığının farklı geometrili takımlarla delinmesinde minimum delaminasyon oluşumu için proses parametrelerinin çok amaçlı optimizasyonu. in: Proceedings of The 5th International Congress On Engineering and Technology Management, 24-25.04.2021, İstanbul, pp.219-231;
  4. Prasanth, R., Prabukarthi, A., Kumar, M.S., Krishnaraj, V. and Rajamani, R.: identification of drill position in CFRP/Titanium alloy stacks using acoustic emission signals, in: Proceedings of the International Conference on Advances in Materials, Manufacturing and Applications (AMMA 2015), 09-11.04.2015, Trichy, pp.1174-1181;
  5. Ekici, E. and Motorcu A. R.: CFRP/Ti6Al4V metalik yığının delinmesinde kesme parametreleri ve delme stratejisinin yüzey pürüzlülüğüne etkisi, in: Proceedings of the 9th International Congress On Engineering, Architecture and Design, İstanbul, Türkiye, 14-16.05.2022, pp.190-197;
  6. Zhang, C., Jia, Z., Wang, F., Zhang, B., Bi, G. and Yin, J.: Design of A New One-Shot Tool with Double Margins Structure in Drilling Titanium/Composite Stacks, in: Proceedings of the 21st International Conference on Composite Materials, 20-25.08.2017, Xi'an, pp.1-8;
  7. Akhil, P.V., Krishnaraj, V., Prabukarthi, A., Kumar, M.S. and Elangovan, S.: Study of tool condition monitoring during drilling of CFRP/Ti stacks under dry and wet conditions, in: Proceedings of the International Conference on Advances in Materials, Manufacturing and Applications (AMMA 2015), 09-11.04.2015, Trichy, pp.839-834;
  8. Paramasivam, S.S.S.S., Kumaran, D. and Natarajan, H.: Taguchi Additive Ratio Assessment (ARAS) method in multi-criteria decision making: A case study for treated drill tools performance. Int. J. Mod. Manuf., Vol.12, No.1, pp.114-124, 2020;

Cited by

See all 12

Metadata

Authors
Motorcu, A., & Ekici, E.
Affiliations
Çanakkale Onsekiz Mart Üniversitesi (TR)
Venue
FME Transactions
Published
2022
Volume
50
Issue
3
Pages
441-460
ISSN
  • 1451-2092 (ISSN-L)
  • 2406-128X
OpenAlex
W4297923018
Cited by
12
References
38
Citations by year
2026: 4 · 2025: 1 · 2024: 5 · 2023: 2
FWCI
0.75
Type
journal article
Language
en
Open access
Locations
  • FME Transaction (publishedVersion, cc-by)
  • Çanakkale Onsekiz Mart University AVESIS (submittedVersion)
  • Çanakkale Onsekiz Mart University Institutional Repository (submittedVersion, cc-by-nc-nd)
  • DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
Funders
Çanakkale Onsekiz Mart Üniversitesi
Topics
  • Physical Sciences › Engineering › Mechanical Engineering › Advanced machining processes and optimization
  • Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Advanced Machining and Optimization Techniques
  • Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Engineering Technology and Methodologies
Keywords
drilling, carbon fiber reinforced polymer, titanium alloys, machinability, surface roughness, dimensional accuracy, roundness error, multi-objective optimization, Taguchi method, ARAS method, tool geometry, cutting speed, feed rate, hybrid composites

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

The claim verdicts this report counts are experimental: their accuracy is not yet measured.

A language model drew the claims from the paper on 2026-09-28, under version 3 of the claim definition (prompt extract-v3).

A second model labelled each claim on 2026-09-28 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).

Cited sources are checked with a language model’s help (gpt-6-sol).

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.