The DOI matches its Crossref record.
Three‐dimensional printed PCL‐hydroxyapatite scaffolds filled with CNT s for bone cell growth stimulation
Abstract
A three‐phase [nanocrystalline hydroxyapatite (HA), carbon nanotubes (CNT), mixed in a polymeric matrix of polycaprolactone (PCL)] composite scaffold produced by 3D printing is presented. The CNT content varied between 0 and 10 wt % in a 50 wt % PCL matrix, with HA being the balance. With the combination of three well‐known materials, these scaffolds aimed at bringing together the properties of all into a unique material to be used in tissue engineering as support for cell growth. The 3D printing technique allows producing composite scaffolds having an interconnected network of square pores in the range of 450–700 μm. The 2 wt % CNT scaffold offers the best combination of mechanical behaviour and electrical conductivity. Its compressive strength of ∼4 MPa is compatible with the trabecular bone. The composites show typical hydroxyapatite bioactivity, good cell adhesion and spreading at the scaffolds surface, this combination of properties indicating that the produced 3D, three‐phase, scaffolds are promising materials in the field of bone regenerative medicine. © 2015 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 104B: 1210–1219, 2016.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cited by
3D printing of polymer matrix composites: A review and prospective
Wang, X., Jiang, M., Zhou, Z., Gou, J., & Hui, D. (2017) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2016.11.034 · Cited by 3,325
Direct Ink Writing: A 3D Printing Technology for Diverse Materials
Saadi, M. A. S. R., Maguire, A., Pottackal, N. T., Thakur, M. S. H., Ikram, M. M., Hart, A. J., Ajayan, P. M., & Rahman, M. M. (2022) · Advanced Materials · doi:10.1002/adma.202108855 · Cited by 1,335
3D bioactive composite scaffolds for bone tissue engineering
Turnbull, G., Clarke, J., Picard, F., Riches, P., Jia, L., Han, F., Li, B., & Shu, W. (2018) · Bioactive Materials · doi:10.1016/j.bioactmat.2017.10.001 · Cited by 1,332
Binder jet 3D printing—Process parameters, materials, properties, modeling, and challenges
Mostafaei, A., Elliott, A. M., Barnes, J. E., Li, F., Tan, W., Cramer, C. L., Nandwana, P., & Chmielus, M. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2020.100707 · Cited by 1,093
Designing Biomaterials for 3D Printing
Guvendiren, M., Molde, J., Soares, R. M. D., & Kohn, J. (2016) · ACS Biomaterials Science & Engineering · doi:10.1021/acsbiomaterials.6b00121 · Cited by 732
Synthesis of hydroxyapatite for biomedical applications
Szcześ, A., Hołysz, L., & Chibowski, E. (2017) · Advances in Colloid and Interface Science · doi:10.1016/j.cis.2017.04.007 · Cited by 719
3D printing of bone tissue engineering scaffolds
Wang, C., Huang, W., Zhou, Y., He, L., He, Z., Chen, Z., He, X., Tian, S., Liao, J., Lu, B., et al. (2020) · Bioactive Materials · doi:10.1016/j.bioactmat.2020.01.004 · Cited by 661
Unagolla, J. M., & Jayasuriya, A. C. (2020) · Applied Materials Today · doi:10.1016/j.apmt.2019.100479 · Cited by 544
3D Bioprinting for Organ Regeneration
Cui, H., Nowicki, M., Fisher, J. P., & Zhang, L. G. (2017) · Advanced Healthcare Materials · doi:10.1002/adhm.201601118 · Cited by 535
3D-printed bioceramic scaffolds: From bone tissue engineering to tumor therapy.
Ma, H., Feng, C., Chang, J., & Wu, C. (2018) · Acta Biomaterialia · doi:10.1016/j.actbio.2018.08.026 · Cited by 512
Nanoparticles in tissue engineering: applications, challenges and prospects
Hasan, A., Morshed, M., Memic, A., Hassan, S., Webster, T., & Marei, H. (2018) · International Journal of Nanomedicine · doi:10.2147/ijn.s153758 · Cited by 496
Carbon nanotubes: a novel material for multifaceted applications in human healthcare
Kumar, S., Rani, R., Dilbaghi, N., Tankeshwar, K., & Kim, K.-H. (2017) · Chemical Society Reviews · doi:10.1039/c6cs00517a · Cited by 397
Arif, Z. U., Khalid, M. Y., Noroozi, R., Sadeghianmaryan, A., Jalalvand, M., & Hossain, M. (2022) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2022.07.140 · Cited by 395
Four-dimensional bioprinting: Current developments and applications in bone tissue engineering
Wan, Z., Zhang, P., Liu, Y., Lv, L., & Zhou, Y. (2020) · Acta Biomaterialia · doi:10.1016/j.actbio.2019.10.038 · Cited by 368
Natural and Synthetic Polymers for Bone Scaffolds Optimization
Donnaloja, F., Jacchetti, E., Soncini, M., & Raimondi, M. T. (2020) · Polymers · doi:10.3390/polym12040905 · Cited by 324
Yang, Y., Chen, Z., Song, X., Zhang, Z., Zhang, J., Shung, K. K., Zhou, Q., & Chen, Y. (2017) · Advanced Materials · doi:10.1002/adma.201605750 · Cited by 316
An Overview on Materials and Techniques in 3D Bioprinting Toward Biomedical Application
Vanaei, S., Parizi, M. S., Vanaei, S., Salemizadehparizi, F., & Vanaei, H. R. (2021) · Engineered Regeneration · doi:10.1016/j.engreg.2020.12.001 · Cited by 308
3D printing: an emerging tool for novel microfluidics and lab-on-a-chip applications
Yazdi, A. A., Popma, A., Wong, W., Nguyen, T., Pan, Y., & Xu, J. (2016) · Microfluidics and Nanofluidics · doi:10.1007/s10404-016-1715-4 · Cited by 307
Binder jetting of ceramics: Powders, binders, printing parameters, equipment, and post-treatment
Lv, X., Ye, F., Cheng, L., Fan, S., & Liu, Y. (2019) · Ceramics International · doi:10.1016/j.ceramint.2019.04.012 · Cited by 302
Machine Learning‐Driven Biomaterials Evolution
Suwardi, A., Wang, F., Xue, K., Han, M., Teo, P., Wang, P., Wang, S., Liu, Y., Ye, E., Li, Z., et al. (2022) · Advanced Materials · doi:10.1002/adma.202102703 · Cited by 299
Additive manufacturing of ceramics: Advances, challenges, and outlook
Dadkhah, M., Tulliani, J.-M., Saboori, A., & Iuliano, L. (2023) · Journal of the European Ceramic Society · doi:10.1016/j.jeurceramsoc.2023.07.033 · Cited by 272
Wang, Y., Wang, J., Gao, R., Liu, X., Feng, Z., Zhang, C., Huang, P., Dong, A., Kong, D., & Wang, W. (2022) · Biomaterials · doi:10.1016/j.biomaterials.2022.121538 · Cited by 268
Kumar, A., Kargozar, S., Baino, F., & Han, S. S. (2019) · Frontiers in Materials · doi:10.3389/fmats.2019.00313 · Cited by 189
Design, printing, and engineering of regenerative biomaterials for personalized bone healthcare
Jia, Z., Xu, X., Zhu, D., & Zheng, Y. (2023) · Progress in Materials Science · doi:10.1016/j.pmatsci.2023.101072 · Cited by 176
3D printing PCL/nHA bone scaffolds: exploring the influence of material synthesis techniques
Zimmerling, A., Yazdanpanah, Z., Cooper, D. M. L., Johnston, J. D., & Chen, X. (2021) · Biomaterials Research · doi:10.1186/s40824-021-00204-y · Cited by 151
Ebrahimi, Z., Irani, S., Ardeshirylajimi, A., & Seyedjafari, E. (2022) · Scientific Reports · doi:10.1038/s41598-022-15602-y · Cited by 141
Cao, Y., Jiang, J., Jiang, Y., Li, Z., Hou, J., & Li, Q. (2022) · Polymers for Advanced Technologies · doi:10.1002/pat.5528 · Cited by 25
Metadata
- Authors
- Gonçalves, E. M., Oliveira, F. J., Silva, R. F., Neto, M. A., Fernandes, M. H., Amaral, M., Vallet‐Regí, M., & Vila, M.
- Venue
- Journal of Biomedical Materials Research Part B: Applied Biomaterials
- Publisher
- Wiley
- Published
- 2015-06-19
- Volume
- 104
- Issue
- 6
- Pages
- 1210-1219
- ISSN
- 1552-4973 (ISSN-L)
- 1552-4981
- OpenAlex
- W1552151947
- Cited by
- 221
- References
- 0
- FWCI
- 6.76
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.