Mechanical behavior of human trabecular bone after overloading
The DOI matches its Crossref record; 33 of the 33 references it cites were found in a registry or an index.
Abstract
With the etiology of osteoporotic fractures as motivation, the goal of this study was to characterize the mechanical behavior of human trabecular bone after overloading. Specifically, we quantified the reductions in modulus and strength and the development of residual deformations and determined the dependence of these parameters on the applied strain and apparent density. Forty cylindrical specimens of human L1 vertebral trabecular bone were destructively loaded in compression at 0.5% strain per second to strains of up to 3.0% and then immediately unloaded to zero stress and reloaded. (An ancillary experiment on more readily available bovine bone had been performed previously to develop this testing protocol.) In general, the reloading stress‐strain curve had a short initial nonlinear region with a tangent modulus similar to Young's modulus. This was followed by an approximately linear region spanning to 0.7% strain, with a reduced residual modulus. The reloading curve always approached the extrapolated envelope of the original loading curve. Percent modulus reduction (between Young's and residual), a quantitative measure of mechanical damage, ranged from 5.2 to 91.0% across the specimens. It increased with increasing plastic strain (r 2 = 0.97) but was not related to modulus or apparent density. Percent strength reduction, in the range of 3.6–63.8%, increased with increasing plastic strain (r 2 = 0.61) and decreasing apparent density (r 2 = 0.23). The residual strains of up to 1.05% depended strongly on applied strain (r 2 = 0.96). Statistical comparisons with previous data for bovine tibial bone lend substantial generality to these trends and provide an envelope of expected behavior for other sites. In addition to providing a basis for biomechanical analysis of the effects of damage in trabecular bone at the organ level, these findings support the concept that occasional overloads may increase the risk of fracture by substantially degrading the mechanical properties of the underlying trabecular bone.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“If a specimen is compressed beyond yield (not exceeding 5% strain), unloaded, and reloaded, permanent residual strains and a loss of stiffness (as quantified by a comparison of the slope of the unloading curve to the initial elastic modulus) and strength occur (Figure 1d) (80).”
From Bone Mechanical Properties in Healthy and Diseased States (2018) · cites this paper as [80]
Citations
Cites
Risk Factors for Hip Fracture in White Women
Cummings, S. R., Nevitt, M. C., Browner, W. S., Stone, K., Fox, K. M., Ensrud, K. E., Cauley, J., Black, D., & Vogt, T. M. (1995) · New England Journal of Medicine · doi:10.1056/nejm199503233321202 · Cited by 3,595
Cooper, C., Atkinson, E. J., MichaelO'Fallon, W., & Dr. Melton, J. L. (1992) · Journal of Bone and Mineral Research · doi:10.1002/jbmr.5650070214 · Cited by 1,528 · cited 1×
“Although not yet known, this might also apply to the spine because as many as 50% of these fractures are associated with falls (5,30), and destructive loads can also occur with heavy lifting (31).”
BackgroundIn vivo measurement of human tibial strains during vigorous activity
Burr, D. B., Milgrom, C., Fyhrie, D., Forwood, M., Nyska, M., Finestone, A., Hoshaw, S., Saiag, E., & Simkin, A. (1996) · Bone · doi:10.1016/8756-3282(96)00028-2 · Cited by 712 · cited 1×
“2% (2); however, this does not imply that strains cannot be higher in situations when the bone is loaded close to but not beyond the point of overt fracture.”
BackgroundMcCalden, R. W., McGeough, J. A., Barker, M. B., & Court-Brown, C. M. (1993) · The Journal of Bone & Joint Surgery · doi:10.2106/00004623-199308000-00009 · Cited by 709 · cited 1×
“ductile than younger bone (4,27), damages more easily than younger tissue when subjected to the same strain (6).”
BackgroundBone Microdamage and Skeletal Fragility in Osteoporotic and Stress Fractures
Burr, D. B., Forwood, M. R., Fyhrie, D. P., Martin, R. B., Schaffler, M. B., & Turner, C. H. (1997) · Journal of Bone and Mineral Research · doi:10.1359/jbmr.1997.12.1.6 · Cited by 686 · cited 2×
“Damage and repair of individual trabeculae is a normal physiologic process (3,15) that increases with age (10,14,28).”
BackgroundYield strain behavior of trabecular bone
Kopperdahl, D. L., & Keaveny, T. M. (1998) · Journal of Biomechanics · doi:10.1016/s0021-9290(98)00057-8 · Cited by 653 · cited 2×
“method has been validated Tor monotonic loading (21,23).”
BackgroundMethodSelf-citationAging of bone tissue: mechanical properties.
Burstein, A. H., Reilly, D. T., & Martens, M. A. (1976) · PubMed · Cited by 614
Classification of vertebral fractures
Eastell, R., Cedel, S. L., Wahner, H. W., Riggs, B. L., & Dr. Melton, L. J. (1991) · Journal of Bone and Mineral Research · doi:10.1002/jbmr.5650060302 · Cited by 610
Aging of bone tissue: mechanical properties
Burstein, A., Reilly, D., & Martens, M. (1976) · The Journal of Bone & Joint Surgery · doi:10.2106/00004623-197658010-00015 · Cited by 569 · cited 1×
“ductile than younger bone (4,27), damages more easily than younger tissue when subjected to the same strain (6).”
BackgroundPrediction of vertebral body compressive fracture using quantitative computed tomography.
McBroom, R. J., Hayes, W. C., Edwards, W. T., Goldberg, R. P., & White, A. A. (1985) · The Journal of Bone & Joint Surgery · doi:10.2106/00004623-198567080-00010 · Cited by 432
Cited by
Bone Mechanical Properties in Healthy and Diseased States
Morgan, E. F., Unnikrisnan, G. U., & Hussein, A. I. (2018) · Annual Review of Biomedical Engineering · doi:10.1146/annurev-bioeng-062117-121139 · Cited by 1,026
“If a specimen is compressed beyond yield (not exceeding 5% strain), unloaded, and reloaded, permanent residual strains and a loss of stiffness (as quantified by a comparison of the slope of the unloading curve to the initial elastic modulus) and strength occur (Figure 1d) (80).”
Biomechanics of Trabecular Bone
Keaveny, T. M., Morgan, E. F., Niebur, G. L., & Yeh, O. C. (2001) · Annual Review of Biomedical Engineering · doi:10.1146/annurev.bioeng.3.1.307 · Cited by 801
“fashion with increasing total applied strain (89).”
InfluentialSelf-citationBiomechanics and Mechanobiology of Trabecular Bone: A Review
Oftadeh, R., Perez-Viloria, M., Villa-Camacho, J. C., Vaziri, A., & Nazarian, A. (2015) · Journal of Biomechanical Engineering · doi:10.1115/1.4029176 · Cited by 547
Effects of Bone Cement Volume and Distribution on Vertebral Stiffness After Vertebroplasty
Liebschner, M. A. K., Rosenberg, W. S., & Keaveny, T. M. (2001) · Spine · doi:10.1097/00007632-200107150-00009 · Cited by 470
“The elastic properties of the damaged trabecular bone elements were then reduced according to empirical relations developed for human vertebral trabecular bone (Figure 2) with a maximum percent reduction of 85%.(17) Trabecular bone elastic properties of elements strained below the yield point were reduced also using t…”
MethodResultSelf-citationZhou, T., Gao, B., Fan, Y., Liu, Y., Feng, S., Cong, Q., Zhang, X., Zhou, Y., Yadav, P. S., Lin, J., et al. (2020) · eLife · doi:10.7554/elife.52779 · Cited by 392
“However, abnormal loading leads to cartilage damage and osteoarthritis as well as pathological bone alterations that may result in fracture when accumulated (Astur et al., 2016; Keaveny et al., 1999).”
BackgroundDental implant induced bone remodeling and associated algorithms
Lin, D., Li, Q., Li, W., & Swain, M. (2009) · Journal of the Mechanical Behavior of Biomedical Materials · doi:10.1016/j.jmbbm.2008.11.007 · Cited by 194
Micro-CT finite element model and experimental validation of trabecular bone damage and fracture
Hambli, R. (2013) · Bone · doi:10.1016/j.bone.2013.06.028 · Cited by 136
“It has been reported by other studies that the failure process of bone is controlled by strain [2,4,17,33–35,40,41].”
BackgroundResultStandardizing compression testing for measuring the stiffness of human bone
Zhao, S., Arnold, M. C. A., Ma, S., Abel, R. L., Cobb, J. P., Hansen, U. N., & Boughton, O. R. (2018) · Bone and Joint Research · doi:10.1302/2046-3758.78.bjr-2018-0025.r1 · Cited by 151
A three-dimensional elastic plastic damage constitutive law for bone tissue
Garcia, D., Zysset, P. K., Charlebois, M., & Curnier, A. (2008) · Biomechanics and Modeling in Mechanobiology · doi:10.1007/s10237-008-0125-2 · Cited by 137
Crawford, R. P., Rosenberg, W. S., & Keaveny, T. M. (2003) · Journal of Biomechanical Engineering · doi:10.1115/1.1589772 · Cited by 121
Self-citationThurner, P. J., Erickson, B. W., Jungmann, R., Schriock, Z., Weaver, J. C., Fantner, G. E., Schitter, G., Morse, D. E., & Hansma, P. K. (2006) · Engineering Fracture Mechanics · doi:10.1016/j.engfracmech.2006.05.024 · Cited by 123
“Mechanical testing of trabecular bone is a vast experimental field [3,6,11–14,31].”
BackgroundBiomechanical consequences of an isolated overload on the human vertebral body
Kopperdahl, D. L., Pearlman, J. L., & Keaveny, T. M. (2000) · Journal of Orthopaedic Research · doi:10.1002/jor.1100180502 · Cited by 120
Self-citationCompressive fatigue behavior of human vertebral trabecular bone
Rapillard, L., Charlebois, M., & Zysset, P. K. (2006) · Journal of Biomechanics · doi:10.1016/j.jbiomech.2005.04.033 · Cited by 113
“This asymptomatic characteristic suggests that repetitive loading lower than ultimate loads, associated with low bone mass and microarchitectural deterioration, may be causing these fractures (Keaveny et al., 1999; Kopperdahl et al., 2000).”
BackgroundNonlinear Behavior of Trabecular Bone at Small Strains
Morgan, E. F., Yeh, O. C., Chang, W. C., & Keaveny, T. M. (2001) · Journal of Biomechanical Engineering · doi:10.1115/1.1338122 · Cited by 107
Self-citationMicrodamage Accumulation in Bovine Trabecular Bone in Uniaxial Compression
Moore, T. L. A., & Gibson, L. J. (2002) · Journal of Biomechanical Engineering · doi:10.1115/1.1428745 · Cited by 103
Verhulp, E. E., van Rietbergen, B., Müller, R., & Huiskes, R. (2008) · Journal of Biomechanics · doi:10.1016/j.jbiomech.2008.02.032 · Cited by 102
“In particular the softening behavior, typically seen in compression experiments of trabecular bone specimens (Røhl et al., 1991; Fyhrie and Schaffler, 1994; Keaveny et al., 1999), was not reproduced.”
BackgroundRelative roles of microdamage and microfracture in the mechanical behavior of trabecular bone
Yeh, O. C., & Keaveny, T. M. (2001) · Journal of Orthopaedic Research · doi:10.1016/s0736-0266(01)00053-5 · Cited by 93
Self-citationLambers, F. M., Bouman, A. R., Rimnac, C. M., & Hernandez, C. J. (2013) · PLoS ONE · doi:10.1371/journal.pone.0083662 · Cited by 86
“Only 51% of all vertebral fractures are associated with a discrete loading event, suggesting that many vertebral fractures are the result of tissue damage caused by multiple loading events over time [3,4].”
BackgroundMechanical Loading: Bone Remodeling and Cartilage Maintenance
Yokota, H., Leong, D. J., & Sun, H. B. (2011) · Current Osteoporosis Reports · doi:10.1007/s11914-011-0067-y · Cited by 95
“Mechanical loading affects bone remodeling in an intensitydependent manner (Table 1). A lack of mechanical stimulation, as seen in bedridden patients or astronauts during spaceflight, leads to rapid loss of bone mass [1, 2], whereas mechanical overloading can cause bone fractures [ 3 , 4]. During growth, moderate exer…”
Hambli, R., Bettamer, A., & Allaoui, S. (2011) · Medical Engineering & Physics · doi:10.1016/j.medengphy.2011.07.011 · Cited by 89
Damage accumulation in vertebral trabecular bone depends on loading mode and direction
Wolfram, U., Wilke, H., & Zysset, P. K. (2011) · Journal of Biomechanics · doi:10.1016/j.jbiomech.2011.01.018 · Cited by 84
Hambli, R. (2012) · Medical & Biological Engineering & Computing · doi:10.1007/s11517-012-0986-5 · Cited by 84
“Several studies showed that bone exhibits a quasi-brittle material behavior [5, 14, 16, 32-34, 62] or brittle behavior [31, 43, 68, 88] depending mainly on the deformation rate applied and the bone properties.”
BackgroundHambli, R., & Allaoui, S. (2013) · Annals of Biomedical Engineering · doi:10.1007/s10439-013-0864-9 · Cited by 85
Verhulp, E. E., van Rietbergen, B., Müller, R., & Huiskes, R. (2008) · Computer Methods in Biomechanics & Biomedical Engineering · doi:10.1080/10255840701848756 · Cited by 79
“load-displacement curve seen during compression of trabecular bone specimens (Røhl et al. 1991; Fyhrie and Schaffler 1994; Keaveny et al. 1999).”
BackgroundKelly, N., & McGarry, P. (2011) · Journal of the mechanical behavior of biomedical materials/Journal of mechanical behavior of biomedical materials · doi:10.1016/j.jmbbm.2011.11.013 · Cited by 88
“Previous studies investigating non-linear trabecular bone mechanics have uncovered viscoelastic, damage and elasto-plastic behaviour (Linde, 1994; Keaveny et al., 1999; Moore and Gibson, 2002a).”
BackgroundBojairami, I. E., El-Monajjed, K., & Driscoll, M. (2020) · Scientific Reports · doi:10.1038/s41598-020-77469-1 · Cited by 80
Viscoelastic behaviour and failure of bovine cancellous bone under constant strain rate
Guedes, R. M., Simöes, J. A., & Morais, J. J. L. (2004) · Journal of Biomechanics · doi:10.1016/j.jbiomech.2004.11.005 · Cited by 76
Material heterogeneity in cancellous bone promotes deformation recovery after mechanical failure
Torres, A. M., Matheny, J. B., Keaveny, T. M., Taylor, D., Rimnac, C. M., & Hernandez, C. J. (2016) · Proceedings of the National Academy of Sciences · doi:10.1073/pnas.1520539113 · Cited by 64
Self-citationTang, S. Y., & Vashishth, D. (2007) · Bone · doi:10.1016/j.bone.2006.10.031 · Cited by 59
“In the context of mechanical modulus reduction, also known as damage fraction, (D=1- 1Eeffective/E), many definitions have been proposed for the “effective modulus” term (Eeffective), including a reloading modulus [29], loading-unloading intersection modulus [3], a “perfect damage” modulus [31,32], a stress-divided-by…”
BackgroundDamage in trabecular bone at small strains
Morgan, E., Yeh, O., & Keaveny, T. (2005) · European Journal of Morphology · doi:10.1080/09243860500095273 · Cited by 59
Self-citationQuantitative relationships between microdamage and cancellous bone strength and stiffness
Hernandez, C. J., Lambers, F. M., Widjaja, J., Chapa, C., & Rimnac, C. M. (2014) · Bone · doi:10.1016/j.bone.2014.05.023 · Cited by 55
“The previous study in vertebral cancellous bone [22], however, used a definition of percent reduction in Young’s modulus based on a different portion of the reload curve explaining the larger percent reduction reported.”
InfluentialThe Biomechanical Effect of Vertebroplasty on the Adjacent Vertebral Body: A Finite Element Study
Wilcox, R. K. (2006) · Proceedings of the Institution of Mechanical Engineers Part H Journal of Engineering in Medicine · doi:10.1243/09544119h00305 · Cited by 56
A Review on Recent Advances in the Constitutive Modeling of Bone Tissue
Pahr, D. H., & Reisinger, A. (2020) · Current Osteoporosis Reports · doi:10.1007/s11914-020-00631-1 · Cited by 57
Hambli, R., & Thurner, P. J. (2013) · Journal of the mechanical behavior of biomedical materials/Journal of mechanical behavior of biomedical materials · doi:10.1016/j.jmbbm.2013.07.005 · Cited by 51
“In addition, numerous studies showed that damage threshold strains and stresses of trabecular and cortical bone tissue are different in tension and compression (Reilly and Burstein, 1975; Currey, 1990; Kotha and Guzelsu, 2003; Keaveny et al., 1994, 1999, 2001).”
BackgroundResultInfluentialLespessailles, É., Hambli, R., & Ferrari, S. (2016) · BoneKEy Reports · doi:10.1038/bonekey.2016.59 · Cited by 51
“However, failure behavior of bone is non-linear by nature as reported by several authors.(40,57,60) Realistic prediction of bone fracture pattern, fracture force and ultimate apparent stress at fracture requires the simulation of the initiation and subsequent progressive propagation of damage within the bone that take…”
BackgroundYeni, Y. N., Hou, F. J., Ciarelli, T. E., Vashishth, D., & Fyhrie, D. P. (2003) · Annals of Biomedical Engineering · doi:10.1114/1.1569264 · Cited by 52
Baroud, G., Nemes, J. A., Ferguson, S. J., & Steffen, T. (2003) · Computer Methods in Biomechanics & Biomedical Engineering · doi:10.1080/1025584031000095746 · Cited by 48
“The time dependency of the viscoelastic model will help to understand potential accumulative damage in bone trabeculae under dynamic loading better, as it has been reported to be characteristic of vertebral cancellous bone [16].”
BackgroundMcNamara, I., Deshpande, S. S., & Porteous, M. J. (2010) · Journal of Bone and Joint Surgery - British Volume · doi:10.1302/0301-620x.92b5.23044 · Cited by 43
Determinants of bone damage: An ex-vivo study on porcine vertebrae
Mirzaali, M. J., Libonati, F., Ferrario, D., Rinaudo, L., Messina, C., Ulivieri, F. M., Cesana, B. M., Strano, M., & Vergani, L. M. (2018) · PLoS ONE · doi:10.1371/journal.pone.0202210 · Cited by 39
Parkesh, R., Lee, T. C., & Gunnlaugsson, T. (2009) · Tetrahedron Letters · doi:10.1016/j.tetlet.2009.04.115 · Cited by 39
Density and architecture have greater effects on the toughness of trabecular bone than damage
Garrison, J. G., Slaboch, C. L., & Niebur, G. L. (2009) · Bone · doi:10.1016/j.bone.2008.12.030 · Cited by 40
“In human trabecular bone, the relative strength reduction was greater for specimens with lower apparent densities [14].”
BackgroundEvolution of Vertebroplasty: A Biomechanical Perspective
Sun, K., & Liebschner, M. A. K. (2003) · Annals of Biomedical Engineering · doi:10.1023/b:abme.0000007793.49771.6d · Cited by 37
Trabecular Architecture and Vertebral Fragility in Osteoporosis
Fields, A. J., & Keaveny, T. M. (2012) · Current Osteoporosis Reports · doi:10.1007/s11914-012-0097-0 · Cited by 37
“nated by the magnitude of the applied loading to the bone, being mostly independent of density and architecture for any given value of applied strain [46].”
BackgroundSelf-citationTrabecular bone strain changes associated with subchondral stiffening of the proximal tibia
McKinley, T. O., & Bay, B. K. (2003) · Journal of Biomechanics · doi:10.1016/s0021-9290(02)00386-x · Cited by 34
“Alternatively, significant increases in strain in the trabecular bone surrounding a stiffened segment could weaken local trabecula (Keaveny et al., 1999; Wachtel and Keaveny, 1997) leading to local trabecular fractures.”
BackgroundWerner, B., Ovesy, M., & Zysset, P. K. (2019) · International Journal for Numerical Methods in Biomedical Engineering · doi:10.1002/cnm.3188 · Cited by 32
Metzner, F., Neupetsch, C., Fischer, J.-P., Drossel, W. G., Heyde, C.-E., & Schleifenbaum, S. (2021) · Scientific Reports · doi:10.1038/s41598-021-92685-z · Cited by 33
Fractures of the proximal femur: correlates of radiological evidence of osteoporosis
Patel, S. H., & Murphy, K. (2006) · Skeletal Radiology · doi:10.1007/s00256-005-0065-1 · Cited by 41
Slyfield, C. R., Tkachenko, E. V., Fischer, S. E., Ehlert, K. M., Yi, I. H., Jekir, M. G., OʼBrien, R. G., Keaveny, T. M., & Hernandez, C. J. (2012) · Bone · doi:10.1016/j.bone.2012.02.636 · Cited by 32
“It has been shown that cancellous bone submitted to a compressive overload experiences large reductions in Young’s modulus upon reloading, presumably as a result of microdamage caused during the overload [19, 21].”
BackgroundSelf-citationTowards patient‐specific material modeling of trabecular bone post‐yield behavior
Carretta, R., Lorenzetti, S., & Müller, R. (2012) · International Journal for Numerical Methods in Biomedical Engineering · doi:10.1002/cnm.2516 · Cited by 34
“At zero plastic strain, which is within the elastic field, modulus reduction was observed [85].”
BackgroundLocalized Damage in Vertebral Bone Is Most Detrimental in Regions of High Strain Energy Density
Kopperdahl, D. L., Roberts, A. D., & Keaveny, T. M. (1999) · Journal of Biomechanical Engineering · doi:10.1115/1.2800864 · Cited by 35
Self-citationShear strength and toughness of trabecular bone are more sensitive to density than damage
Garrison, J. G., Gargac, J. A., & Niebur, G. L. (2011) · Journal of Biomechanics · doi:10.1016/j.jbiomech.2011.09.002 · Cited by 32
“The progressively higher modulus reductions as a function of the compressive strain magnitude complement previous studies (Keaveny et al., 1999; Arthur Moore and Gibson, 2002), although the modulus reductions we measured are lower, because we measured the reloading modulus rather than using the secant modulus to quant…”
BackgroundModeling Modulus Reduction in Bovine Trabecular Bone Damaged in Compression
Moore, T. L. A., & Gibson, L. J. (2001) · Journal of Biomechanical Engineering · doi:10.1115/1.1407828 · Cited by 34
Effect of pelvis impact angle on stresses at the femoral neck during falls
Choi, W. J., & Robinovitch, S. N. (2018) · Journal of Biomechanics · doi:10.1016/j.jbiomech.2018.04.015 · Cited by 29
A computational insight on damage-based constitutive modelling in femur mechanics
Gaziano, P., Falcinelli, C., & Vairo, G. (2022) · European Journal of Mechanics - A/Solids · doi:10.1016/j.euromechsol.2022.104538 · Cited by 28
Sun, H. B., Zhao, L., Tanaka, S., & Yokota, H. (2011) · Connective Tissue Research · doi:10.3109/03008207.2011.628765 · Cited by 28
“A lack of mechanical stimulation, as seen in bedridden patients or astronauts during spaceflight, leads to rapid loss of bone mass [2], while mechanical overloading causes bone fractures [3].”
Karali, A., Kao, A. P., Zekonyte, J., Blunn, G. W., & Tozzi, G. (2020) · Journal of the mechanical behavior of biomedical materials/Journal of mechanical behavior of biomedical materials · doi:10.1016/j.jmbbm.2020.104298 · Cited by 27
Lim, K., & Choi, W. J. (2019) · Journal of Biomechanics · doi:10.1016/j.jbiomech.2019.06.002 · Cited by 26
Mohamad, N.-V., Zulkepli, M. A. A. C., Theseira, K. M., Zulkifli, N., Shahrom, N. Q., Ridzuan, N. A. M., Jamil, N. A., Soelaiman, I. N., & Chin, K. (2018) · International Journal of Medical Sciences · doi:10.7150/ijms.22732 · Cited by 25
“Stress is the strength of the bone tissue under a given loading condition, whereas strain represents ductility of the bone [34].”
BackgroundMaslov, L. B., Borovkov, A. I., Maslova, I., Soloviev, D., Zhmaylo, M., & Тарасенко, Ф. (2021) · Materials · doi:10.3390/ma14227066 · Cited by 24
Structural strength of cancellous specimens from bovine femur under cyclic compression
Endo, K., Yamada, S., Masahiro Todoh, A., Takahata, M., Iwasaki, N., & TADANO, S. (2016) · PeerJ · doi:10.7717/peerj.1562 · Cited by 30
Finite Element Modeling of Trabecular Bone Damage
Kosmopoulos, V., & Keller, T. S. (2003) · Computer Methods in Biomechanics & Biomedical Engineering · doi:10.1080/1025584031000149089 · Cited by 24
“Vertebral trabecular bone is a highly loaded structure and when overloaded may be damaged resulting in reduced modulus and strength [10,11].”
BackgroundZhang, N., Magland, J. F., Rajapakse, C. S., Bhagat, Y. A., & Wehrli, F. W. (2013) · Medical Physics · doi:10.1118/1.4802085 · Cited by 23
Ayagara, A. R., Langlet, A., & Hambli, R. (2019) · Journal of the mechanical behavior of biomedical materials/Journal of mechanical behavior of biomedical materials · doi:10.1016/j.jmbbm.2019.05.031 · Cited by 22
Collagen glycation and its role in fracture properties of bone.
Vashishth, D. (2005) · PubMed · Cited by 22
Fatigue-caused damage in trabecular bone from clinical, morphological and mechanical perspectives
Mirzaali, M. J., Libonati, F., Böhm, C., Rinaudo, L., Cesana, B. M., Ulivieri, F. M., & Vergani, L. M. (2019) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2019.105451 · Cited by 24
Kennedy, O. D., Brennan, O., Mahony, N. J., Rackard, S. M., O’Brien, F. J., Taylor, D. M., & Lee, C. T. (2008) · Spine · doi:10.1097/brs.0b013e318186b292 · Cited by 24
“Specimens were then unloaded to 200 N and held for 1 minute to minimize viscoelastic creep and to reach a steady-state displacement.(24,25) They were then reloaded, under the same conditions, to 10% strain.”
MethodInfluence of Orthogonal Overload on Human Vertebral Trabecular Bone Mechanical Properties
Badiei, A., Bottema, M. J., & Fazzalari, N. L. (2007) · Journal of Bone and Mineral Research · doi:10.1359/jbmr.070706 · Cited by 21
“These findings are supported by the work of Fyhrie and Schaffler((5)) and others.((2,7,8,32,33)) Fyhrie and Schaffler took”
BackgroundResultInfluential2D and 3D numerical models to evaluate trabecular bone damage
Buccino, F., Colombo, C., Duarte, D. H. L., Rinaudo, L., Ulivieri, F. M., & Vergani, L. M. (2021) · Medical & Biological Engineering & Computing · doi:10.1007/s11517-021-02422-x · Cited by 20
Sensitivity of Vertebral Compressive Strength to Endplate Loading Distribution
Buckley, J. M., Leang, D. C., & Keaveny, T. M. (2006) · Journal of Biomechanical Engineering · doi:10.1115/1.2241637 · Cited by 20
Self-citationAlterations in damage processes in dense cancellous bone following gamma-radiation sterilization
Dux, S. J., Ramsey, D. S., Chu, E. H., Rimnac, C. M., & Hernandez, C. J. (2010) · Journal of Biomechanics · doi:10.1016/j.jbiomech.2010.01.042 · Cited by 20
“(Keaveny et al., 1999).”
ResultA 1D elastic plastic damage constitutive law for bone tissue
García, D., Zysset, P. K., Charlebois, M., & Curnier, A. (2009) · Archive of Applied Mechanics · doi:10.1007/s00419-009-0382-2 · Cited by 22
“On the one hand, the general damage model proposed by [20] did not predict a linear damaged reloading curve collinear with the origin as many tensile and compressive experiments on compact and trabecular bone have shown [7, 10 ,11] (i.e.”
BackgroundA Phenomenological Model for Predicting Fatigue Life in Bovine Trabecular Bone
Ganguly, P., Moore, T. L. A., & Gibson, L. J. (2004) · Journal of Biomechanical Engineering · doi:10.1115/1.1762893 · Cited by 21
Frazer, L. L., Santschi, E. M., & Fischer, K. J. (2018) · Veterinary Surgery · doi:10.1111/vsu.13139 · Cited by 18
Li, S., Kim, Y.-W., Choi, M.-S., & Nam, T.-H. (2019) · Intermetallics · doi:10.1016/j.intermet.2019.106631 · Cited by 18
Development of a crushable foam model for human trabecular bone
Soltanihafshejani, N., Bitter, T., Janssen, D. W., & Verdonschot, N. J. J. (2021) · Medical Engineering & Physics · doi:10.1016/j.medengphy.2021.08.009 · Cited by 21
“[6, 20-22] performed comprehensive studies on the prediction of post-failure behavior of bone in uniaxial configurations.”
BackgroundThe Mechanical Properties of Bone
Fyhrie, D. P. (2010) · Elsevier eBooks · doi:10.1016/b978-0-12-374602-3.00005-5 · Cited by 21
Khorshidparast, S., Akhlaghi, P., Rouhi, G., & Barikani, H. (2022) · Journal of the mechanical behavior of biomedical materials/Journal of mechanical behavior of biomedical materials · doi:10.1016/j.jmbbm.2022.105566 · Cited by 17
Bettamer, A., Hambli, R., Allaoui, S., & Almhdie-Imjabbar, A. (2015) · Computer Methods in Biomechanics and Biomedical Engineering Imaging & Visualization · doi:10.1080/21681163.2015.1079505 · Cited by 17
“Numerous studies showed that the damage threshold strains and stresses of trabecular and cortical bone tissue are different in tension and compression (Reilly & Burstein 1974, 1975; Currey 1990; Keaveny et al. 1994, 1999, 2001; Kotha & Guzelsu 2003; Wolfram et al. 2011).”
BackgroundNon-linear viscoelastic constitutive model for bovine cortical bone tissue
Pawlikowski, M., & Barcz, K. (2016) · Journal of Applied Biomedicine · doi:10.1016/j.bbe.2016.03.005 · Cited by 16
Biomechanics of Vertebral Bone
Keaveny, T. M., & Buckley, J. M. (2006) · Elsevier eBooks · doi:10.1016/b978-012369390-7/50005-8 · Cited by 20
Self-citationElsayed, S., Ahmed, Y., El-Anwar, M. I., Elddamony, E., & Ashraf, R. (2025) · BMC Oral Health · doi:10.1186/s12903-025-05440-5 · Cited by 16
“Knowing that spongy bone tension and compression yield strengths are in the range of 1.75 MPa and 2.25 MPa respectively [57–59].”
InfluentialBiomechanical aspects of bone repair
Lacroix, D. (2019) · Elsevier eBooks · doi:10.1016/b978-0-08-102451-5.00003-2 · Cited by 22
The Effect of Damage on the Viscoelastic Behavior of Human Vertebral Trabecular Bone
Bredbenner, T. L., & Davy, D. T. (2006) · Journal of Biomechanical Engineering · doi:10.1115/1.2205370 · Cited by 16
Mechanical properties of whole-body human bones: a review
Verma, S., Singh, G., Choudhary, A., Hussain, S., & Chanda, A. (2026) · Materials Research Express · doi:10.1088/2053-1591/ae45f3 · Cited by 14
Hernandez, C. J. (2016) · Springer eBooks · doi:10.1007/978-1-4939-3305-1_2 · Cited by 14
From Tension to Compression: Asymmetric Mechanical Behaviour of Trabecular Bone’s Organic Phase
Xie, S., Wallace, R. J., Callanan, A., & Pankaj, P. (2018) · Annals of Biomedical Engineering · doi:10.1007/s10439-018-2009-7 · Cited by 15
Woo, D. G., Won, Y., Kim, H. S., & Lim, D. (2007) · Journal of Mechanical Science and Technology · doi:10.1007/bf03026963 · Cited by 14
“Keaveny et al. (1999) studied the mechanical characteristics of human trabecular bone after over loading.”
BackgroundTrabecular Bone Strain Changes Associated With Subchondral Bone Defects of the Tibial Plateau
Brown, A. N., McKinley, T. O., & Bay, B. K. (2002) · Journal of Orthopaedic Trauma · doi:10.1097/00005131-200210000-00005 · Cited by 13
“Trabecular bone is weakened when subjected to excessive strain (14,26).”
BackgroundEffect of including damage at the tissue level in the nonlinear homogenisation of trabecular bone
Levrero-Florencio, F., Manda, K., Margetts, L., & Pankaj, P. (2017) · Biomechanics and Modeling in Mechanobiology · doi:10.1007/s10237-017-0913-7 · Cited by 15
“Damage behaviour of bone at different scales has been studied and modelled in several studies (Keaveny et al. 1999; Schwiedrzik and Zysset 2013; Garcia et al. 2009).”
ResultBone Response to Mechanical Loads
Ramaswamy, G., Bidez, M. W., & Misch, C. E. (2014) · Elsevier eBooks · doi:10.1016/b978-0-323-07845-0.00006-3 · Cited by 15
Biomechanical properties of the bone during implant placement
Nagy, Á. L., Tóth, Z., Tarjányi, T., Práger, N. T., & Baráth, Z. (2021) · BMC Oral Health · doi:10.1186/s12903-021-01442-1 · Cited by 12
Tsouknidas, A., Maliaris, G., Savvakis, S., & Michailidis, N. (2013) · Computer Methods in Biomechanics & Biomedical Engineering · doi:10.1080/10255842.2013.849342 · Cited by 12
“It is noteworthy that the introduced stress–strain approach is the only approach indicating a post-yield descent of the load–displacement curve (see Figure 7) which is typical for trabecular bone samples (Keaveny et al. 1999).”
BackgroundEffects of damage on the orthotropic material symmetry of bovine tibial trabecular bone
Liu, X., Wang, X., & Niebur, G. L. (2003) · Journal of Biomechanics · doi:10.1016/s0021-9290(03)00217-3 · Cited by 13
Initial anisotropy in demineralized bovine cortical bone in compressive cyclic loading–unloading
Novitskaya, E. E., Lee, S., Lubarda, V. A., & McKittrick, J. M. (2012) · Materials Science and Engineering C · doi:10.1016/j.msec.2012.11.006 · Cited by 12
Equine subchondral lucencies: Knowledge from the medial femoral condyle
Santschi, E. M. (2024) · Veterinary Surgery · doi:10.1111/vsu.14062 · Cited by 11
Biomechanical aspects of bone repair
Lacroix, D. (2009) · Elsevier eBooks · doi:10.1533/9781845696610.1.106 · Cited by 16
3D finite element simulation of human proximal femoral fracture under quasi-static load
Hambli, R. (2013) · Advances in Biomechanics and Applications · doi:10.12989/aba.2013.1.1.001 · Cited by 11
“…finite element simulation of human proximal femoral fracture under quasi-static load suggesting that it exhibits a quasi-brittle material behaviour (Reilly and Burstein 1975, Keaveny et al. 1999, Currey 2002, Kaneko et al.2003, Kotha and Guzelsu 2003, Bayraktar et al. 2004).”
BackgroundMethodTime-dependent damage accumulation under stress relaxation testing of bovine trabecular bone
Nagaraja, S., BALL, M., & Guldberg, R. E. (2006) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2006.09.019 · Cited by 13
Post-yield relaxation behavior of bovine cancellous bone
Burgers, T. A., Lakes, R. S., García-Rodríguez, S., Piller, G. R., & Ploeg, H.-L. (2009) · Journal of Biomechanics · doi:10.1016/j.jbiomech.2009.08.005 · Cited by 10
Schulte, F. A., Marques, F. C., Griesbach, J. K., Weigt, C., von Salis‐Soglio, M., Lambers, F. M., Kreutz, C., Kneissel, M., Richards, P. J., Kuhn, G. A., et al. (2026) · Nature Communications · doi:10.1038/s41467-026-70309-2 · Cited by 11
Metadata
- Authors
- Keaveny, T. M., Wachtel, E. F., & Kopperdahl, D. L.
- Affiliations
- University of California, San Francisco (US)
- University of California, Berkeley (US)
- Corresponding author
- Keaveny, Tony M.
- Venue
- Journal of Orthopaedic Research
- Publisher
- Wiley
- Published
- 1999-05
- Volume
- 17
- Issue
- 3
- Pages
- 346-353
- ISSN
- 0736-0266 (ISSN-L)
- 1554-527X
- OpenAlex
- W2165456908
- Cited by
- 155
- References
- 33
- Citations by year
- 2026: 3 · 2025: 3 · 2024: 3 · 2023: 6 · 2022: 2 · 2021: 9 · 2020: 11 · 2019: 6 · 2018: 10 · 2017: 5 · 2016: 5 · 2015: 3 · 2014: 6 · 2013: 8 · 2012: 7
- FWCI
- 5.22
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Journal of Orthopaedic Research® (publishedVersion)
- PubMed (publishedVersion)
- Funders
- National Institute of Arthritis and Musculoskeletal and Skin Diseases (AR41481)
- Topics
- Health Sciences › Medicine › Orthopedics and Sports Medicine › Bone health and osteoporosis research
- Health Sciences › Medicine › Orthopedics and Sports Medicine › Bone fractures and treatments
- Physical Sciences › Engineering › Biomedical Engineering › Elasticity and Material Modeling
- Keywords
- trabecular bone, mechanical overload, osteoporotic fractures, modulus reduction, strength degradation, residual strain, plastic strain, apparent bone density, compressive loading, vertebral bone, mechanical damage, bone biomechanics
- MeSH terms
- Adult, Aged, Aged, 80 and over, Animals, Biomechanical Phenomena, Elasticity, Female, Humans, Lumbar Vertebrae, Male, Middle Aged, Pressure, Stress, Mechanical
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.