The influence of small amounts of KCl(s) on the high temperature corrosion of a Fe‐2.25Cr‐1Mo steel at 400 and 500°C
The DOI matches its Crossref record; 29 of the 29 references it cites were found in a registry or an index.
Abstract
This paper reports the oxidation behaviour of a low‐alloyed steel (Fe‐2.25Cr‐1Mo) in the presence of small amounts of KCl(s) at 400 and 500°C. Cleaned and polished sample coupons were exposed in a horizontal tube furnace with exposure times ranging from one hour to one week. The flue gas composition was 5% O 2 with 40% H 2 O in N 2, and 0.1 mg KCl/cm 2 was deposited on the samples prior to exposure. X‐ray diffraction (XRD) and scanning electron microscopy (SEM) with energy dispersive X‐ray (EDX) analysis were used to characterize the samples. Cross sections were prepared by means of focused ion beam (FIB) and broad ion beam (BIB). At 400°C there was a modest mass gain in the absence of KCl. In the presence of KCl, mass gain is significantly increased and a rapid attack is evident already after short exposure times. At 500°C, the mass gains in the absence of KCl were considerably higher than at 400°C, especially after 168 hours of exposure. KCl had an effect at shorter exposure times, but after one week the samples exposed with and without KCl had mass gains of comparable magnitude.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“It is anticipated from literature [15,17,20,21], that a mixed deposit chemistry will decrease the melting point of the resulting mixture.This in turn is likely to shift the bell-shaped curve for fireside corrosion damage; moving it towards lower temperatures [15,17,20,21].”
From Fireside corrosion and deposition on heat exchangers in biomass combustion systems (2023) · cites this paper as [21]
Citations
Cites
Thermochemical Data of Pure Substances
Barin, I. (1995) · doi:10.1002/9783527619825 · Cited by 4,241
A quantitative demonstration of the grain boundary diffusion mechanism for the oxidation of metals
Atkinson, A., Taylor, R. I., & Hughes, A. E. (1982) · Philosophical Magazine A · doi:10.1080/01418618208239905 · Cited by 2,540
(2006) · Electrochemistry and Corrosion Science · doi:10.1007/1-4020-7860-9_10 · Cited by 1,814
Introduction to high temperature oxidation of metals
Birks, N., & Meier, G. H. (1983) · Cited by 848
The implications of chlorine-associated corrosion on the operation of biomass-fired boilers
Nielsen, H. P., Frandsen, F. J., Dam-Johansen, K., & Baxter, L. L. (2000) · Progress in Energy and Combustion Science · doi:10.1016/s0360-1285(00)00003-4 · Cited by 785
Review of the High-Temperature Oxidation of Iron and Carbon Steels in Air or Oxygen
Chen, R. Y., & Yeun, W. Y. D. (2003) · Oxidation of Metals · doi:10.1023/a:1023685905159 · Cited by 665
Grabke, H. J., Reese, E., & Spiegel, M. (1995) · Corrosion Science · doi:10.1016/0010-938x(95)00011-8 · Cited by 537
Stott, F. H. (1982) · Corrosion Science · doi:10.1016/0010-938x(82)90037-3 · Cited by 394
Zahs, A., Spiegel, M., & Grabke, H. J. (2000) · Corrosion Science · doi:10.1016/s0010-938x(99)00142-0 · Cited by 365
High temperature corrosion of coatings and boiler steels below chlorine-containing salt deposits
Uusitalo, M. A., Vuoristo, P. M. J., & Mäntylä, T. A. (2004) · Corrosion Science · doi:10.1016/j.corsci.2003.09.026 · Cited by 260
Research works printed but not linked: 6
- Pettersson J., 2008, High Temperature Corrosion and Protection of Materials 7, Pts 1 and 2, 367
- 10.3184/096034009x464339 · doi:10.3184/096034009x464339 · Paper page
- C.Gleave J. M.Calvert D. G.Lees P. C.Rowlands in:Proceedings of the Royal Society of London Series A – Mathematical Physical and Engineering Sciences1982. London. vol. 379 no.1777.
- Pujilaksono B., 2009, Oxidation of Metals
- Pujilaksono B., 2009, Oxidation of Metals
- Jonsson T., 2010, Corrosion Science
Cited by
Ma, W., Wenga, T., Frandsen, F. J., Yan, B., & Chen, G. (2020) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2019.100789 · Cited by 275
Kassman, H., Liske, J., Steenari, B., & Åmand, L.-E. (2011) · Fuel Processing Technology · doi:10.1016/j.fuproc.2011.06.025 · Cited by 168
Alkali Induced High Temperature Corrosion of Stainless Steel: The Influence of NaCl, KCl and CaCl2
Karlsson, S., Pettersson, J., Johansson, L. G., & Svensson, J. E. (2012) · Oxidation of Metals · doi:10.1007/s11085-012-9293-7 · Cited by 118
Self-citationJafari, R., & Sadeghi, E. (2019) · Corrosion Science · doi:10.1016/j.corsci.2019.06.021 · Cited by 92
Jonsson, T., Folkeson, N., Svensson, J., Johansson, L.-G., & Halvarsson, M. (2011) · Corrosion Science · doi:10.1016/j.corsci.2011.03.007 · Cited by 88
Self-citationStudies on the corrosion behavior of Fe-20Cr alloy in NaCl solution spray at 600 °C
Cao, M., Liu, L., Yu, Z., Fan, L., Li, Y., & Wang, F. (2018) · Corrosion Science · doi:10.1016/j.corsci.2018.01.033 · Cited by 66
Sadeghi, E., Markocsan, N., & Joshi, S. V. (2019) · Journal of Thermal Spray Technology · doi:10.1007/s11666-019-00939-0 · Cited by 60
Corrosion of heat exchanger materials in co-combustion thermal power plants
Li, K., & Zeng, Y. (2022) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2022.112328 · Cited by 55
Meißner, T. M., Montero, X., Fähsing, D., & Galetz, M. C. (2020) · Corrosion Science · doi:10.1016/j.corsci.2019.108343 · Cited by 51
Liu, X., Hu, K., Zhang, S., Xu, T., Chen, L., Byon, E., & Liu, D. (2022) · Corrosion Science · doi:10.1016/j.corsci.2022.110351 · Cited by 51
Sulfur recirculation for increased electricity production in Waste-to-Energy plants
Andersson, S., Blomqvist, E. W., Bäfver, L., Jones, F., Davidsson, K., Froitzheim, J., Karlsson, M., Larsson, E., & Liske, J. (2014) · Waste Management · doi:10.1016/j.wasman.2013.09.002 · Cited by 45
Okoro, S. C., Montgomery, M., Frandsen, F. J., & Pantleon, K. (2014) · Energy & Fuels · doi:10.1021/ef5017335 · Cited by 44
Hu, Z., Wang, X., Adeosun, A., Ruan, R., & Tan, H. (2017) · Fuel Processing Technology · doi:10.1016/j.fuproc.2017.11.002 · Cited by 48
KCl-Induced Corrosion of the FeCrAl Alloy Kanthal ® AF at 600 °C and the Effect of H2O
Israelsson, N., Hellström, K., Svensson, J.-E., & Johansson, L.-G. (2015) · Oxidation of Metals · doi:10.1007/s11085-014-9506-3 · Cited by 46
Self-citationKCl‐induced high temperature corrosion of selected commercial alloys: Part I: chromia‐formers
Kiamehr, S., Dahl, K. V., Montgomery, M., & Somers, M. A. J. (2015) · Materials and Corrosion · doi:10.1002/maco.201408213 · Cited by 42
Pan, P., Zhou, W., Zhao, Y., Wang, Y., & Zhang, N. (2021) · Corrosion Science · doi:10.1016/j.corsci.2021.109938 · Cited by 42
Karlsson, S., Jonsson, T., Hall, J., Svensson, J.-E., & Liske, J. (2014) · Energy & Fuels · doi:10.1021/ef402127h · Cited by 41
Self-citationA microstructural investigation into the accelerated corrosion of P91 steel during biomass co-firing
O’Hagan, C. P., O’Brien, B., Leen, S. B., & Monaghan, R. F. D. (2016) · Corrosion Science · doi:10.1016/j.corsci.2016.03.028 · Cited by 38
Effect of Water Vapor on High-Temperature Corrosion under Conditions Mimicking Biomass Firing
Okoro, S. C., Montgomery, M., Frandsen, F., & Pantleon, K. (2015) · Energy & Fuels · doi:10.1021/acs.energyfuels.5b01045 · Cited by 37
Okoro, S. C., Kiamehr, S., Montgomery, M., Frandsen, F. J., & Pantleon, K. (2017) · Materials and Corrosion · doi:10.1002/maco.201609173 · Cited by 27
Corrosion behavior of Ti60 alloy under continuous NaCl solution spraying at 600 °C
Li, R., Liu, L., Cui, Y., Liu, R., Fan, L., Cao, M., Yu, Z., Chen, Z., Wang, Q., & Wang, F. (2022) · Journal of Material Science and Technology · doi:10.1016/j.jmst.2022.01.032 · Cited by 27
Liu, H., Pour, M. S., Mellin, P., Grip, C., Yang, W., & Blasiak, W. (2014) · Energy · doi:10.1016/j.energy.2014.08.092 · Cited by 27
Sui, J., Lehmusto, J., Bergelin, M., & Hupa, L. (2019) · Corrosion Science · doi:10.1016/j.corsci.2019.04.010 · Cited by 26
Li, H., Liu, H., Huang, Y., Chen, X., Zhang, X., Li, J., Xu, L., & Yao, H. (2024) · Corrosion Science · doi:10.1016/j.corsci.2024.111933 · Cited by 26
Persdotter, A., Sattari, M., Larsson, E., Ogaz, M. A. O., Liske, J., & Jonsson, T. (2019) · Corrosion Science · doi:10.1016/j.corsci.2019.108234 · Cited by 26
Self-citationKassman, H. (2012) · Chalmers Publication Library (Chalmers University of Technology) · Cited by 26
Ssenteza, V., Eklund, J., Hanif, I., Liske, J., & Jonsson, T. (2023) · Corrosion Science · doi:10.1016/j.corsci.2022.110896 · Cited by 25
Self-citationWu, D., Liu, S., Yuan, Z., Cao, P., Wei, X., & Zhang, C. (2021) · Corrosion Science · doi:10.1016/j.corsci.2021.109689 · Cited by 25
Kiamehr, S., Dahl, K. V., Montgomery, M., & Somers, M. A. J. (2015) · Materials and Corrosion · doi:10.1002/maco.201408215 · Cited by 24
Deposit Shedding in Biomass-Fired Boilers: Shear Adhesion Strength Measurements
Laxminarayan, Y., Jensen, P. A., Wu, H., Frandsen, F. J., Sander, B., & Glarborg, P. (2017) · Energy & Fuels · doi:10.1021/acs.energyfuels.7b01312 · Cited by 23
Alipour, Y., Henderson, P., & Szakálos, P. (2013) · Materials and Corrosion · doi:10.1002/maco.201307118 · Cited by 23
The long-term corrosion behavior of fecral(Si) alloys after breakaway oxidation at 600 °C
Eklund, J., Persdotter, A., Ssenteza, V., & Jonsson, T. (2023) · Corrosion Science · doi:10.1016/j.corsci.2023.111155 · Cited by 22
Self-citationFantozzi, D., Matikainen, V., Uusitalo, M. A., Koivuluoto, H., & Vuoristo, P. M. J. (2019) · Corrosion Science · doi:10.1016/j.corsci.2019.108166 · Cited by 22
Cantatore, V., Olivas Ogaz, M. A., Liske, J., Jonsson, T., Svensson, J.-E., Johansson, L.-G., & Panas, I. (2019) · The Journal of Physical Chemistry C · doi:10.1021/acs.jpcc.9b06497 · Cited by 19
Self-citationInteractions of PbCl2 with Alkali Salts in Ash Deposits and Effects on Boiler Corrosion
Niemi, J., Kinnunen, H., Lindberg, D., & Enestam, S. H. (2018) · Energy & Fuels · doi:10.1021/acs.energyfuels.8b01722 · Cited by 20
Application of aluminum diffusion coatings to mitigate the KCl‐induced high‐temperature corrosion
Kiamehr, S., Lomholt, T. N., Dahl, K. V., Christiansen, T. L., & Somers, M. A. J. (2016) · Materials and Corrosion · doi:10.1002/maco.201609047 · Cited by 17
Breakdown mechanism of γ-Al2O3 on Ni2Al3 coatings exposed in a biomass fired power plant
Wu, D. L., Dahl, K. V., Grumsen, F. B., Christiansen, T. L., Montgomery, M., & Hald, J. (2020) · Corrosion Science · doi:10.1016/j.corsci.2020.108583 · Cited by 16
Khantisopon, K., Tharajak, J., Nawarat, P., Sanpo, N., & Ang, A. S. M. (2022) · Corrosion Science · doi:10.1016/j.corsci.2022.110470 · Cited by 16
Persdotter, A., Boll, T., & Jonsson, T. (2021) · Corrosion Science · doi:10.1016/j.corsci.2021.109779 · Cited by 16
Self-citationOkoro, S. C., Montgomery, M., Frandsen, F. J., & Pantleon, K. (2015) · Materials at High Temperatures · doi:10.1179/0960340914z.00000000081 · Cited by 14
“Subsequent formation of an unprotective Fe-rich oxide ensues.(30,31) The Cl generated from such a reaction can also diffuse through the unprotective oxide towards the oxide/alloy interface.”
BackgroundAbu-warda, N., López, A. J., Pedraza, F., & Utrilla, M. V. (2020) · Materials and Corrosion · doi:10.1002/maco.202012139 · Cited by 16
The effect of Cl, Br, and F on high-temperature corrosion of heat-transfer alloys
Eriksson, J.-E., Lehmusto, J., Dirbeba, M., Silvander, L., Lindberg, D., & Hupa, L. (2023) · Fuel · doi:10.1016/j.fuel.2023.128516 · Cited by 15
Zhang, H., Yang, L., Zhang, X., Wang, Q., Wu, J., Liu, Z., Zeng, C., & Zhu, S. (2022) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2022.12.152 · Cited by 15
Meißner, T. M., Grégoire, B., Montero, X., Miller, E., Maier, J., & Galetz, M. C. (2020) · Energy & Fuels · doi:10.1021/acs.energyfuels.0c01474 · Cited by 15
Ogaz, M. A. O., Eklund, J., Persdotter, A., Sattari, M., Liske, J., Svensson, J., & Jonsson, T. (2018) · Oxidation of Metals · doi:10.1007/s11085-018-9881-2 · Cited by 15
Self-citationPorosity-Based Corrosion Model for Alkali Halide Ash Deposits during Biomass Co-firing
O’Hagan, C. P., O’Brien, B., Griffin, F., Hooper, B., Leen, S. B., & Monaghan, R. F. D. (2015) · Energy & Fuels · doi:10.1021/ef502275j · Cited by 14
A Comparative Study of the Initial Corrosion of KCl and PbCl2 on a Low-Alloyed Steel
Larsson, E., Gruber, H., Hellström, K., Jonsson, T., Liske, J., & Svensson, J. E. (2017) · Oxidation of Metals · doi:10.1007/s11085-017-9765-x · Cited by 14
Self-citationWu, D., Zheng, J., Liu, S., Wu, H., Wei, X., & Zhang, C. (2022) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2022.07.170 · Cited by 13
Microstructural investigations of Ni and Ni2Al3 coatings exposed in biomass power plants
Wu, D., Dahl, K. V., Christiansen, T. L., Montgomery, M., & Hald, J. K. (2017) · Materials at High Temperatures · doi:10.1080/09603409.2017.1389382 · Cited by 13
Effect of microstructure on KCl corrosion attack of modified AISI 310 steel
Malede, Y. C., Montgomery, M., Dahl, K. V., & Hald, J. K. (2017) · Materials at High Temperatures · doi:10.1080/09603409.2017.1389381 · Cited by 12
The Influence of KCl and HCl on the High-Temperature Oxidation of a Fe-2.25Cr-1Mo Steel at 400 °C
Larsson, E., Liske, J., Persdotter, A., Jonsson, T., Svensson, J., & Johansson, L.-G. (2019) · Oxidation of Metals · doi:10.1007/s11085-019-09943-9 · Cited by 12
“25Cr-1Mo steel to O2 and H2O at 400 °C in the presence of KCl was reported to result in high corrosion rates accompanied by KCl consumption and chlorination of the alloy [17, 18].”
BackgroundResultInfluentialSelf-citationCorrosion of Heat-Transfer Materials Induced by KCl, HCl, and O2 Under Chemical-Looping Conditions
Eriksson, J.-E., Lehmusto, J., Silvander, L., Lindberg, D. M., Zevenhoven, M., Yrjas, P., Brink, A., Hupa, M. M., & Hupa, L. (2024) · High Temperature Corrosion of Materials · doi:10.1007/s11085-024-10250-1 · Cited by 11
Mori, G., Vidic, K., Bucher, E., Yasir, M., Hornauer, D., Nachtnebel, M., Fitzek, H., & Schroettner, H. (2019) · Materials and Corrosion · doi:10.1002/maco.201810451 · Cited by 11
A comparative evaluation of waste wood and herbaceous biomass fireside corrosion behaviours
Sanusi, T., Sumner, J., & Simms, N. J. (2022) · Fuel · doi:10.1016/j.fuel.2022.124070 · Cited by 10
Yazıcı, A., Zeybek, M. S., & Kahraman, F. (2023) · Materials Testing · doi:10.1515/mt-2022-0362 · Cited by 9
KCl‐induced corrosion of Ni‐based alloys containing 35–45 wt% Cr
Malede, Y. C., Simon, J. P., Jonsson, T., Montgomery, M., Dahl, K. V., & Hald, J. (2019) · Materials and Corrosion · doi:10.1002/maco.201810658 · Cited by 8
Self-citationHooshyar, H. (2016) · Chalmers Publication Library (Chalmers University of Technology) · Cited by 9
Fireside corrosion and deposition on heat exchangers in biomass combustion systems
Mori, S., Sanusi, T., Simms, N., & Sumner, J. (2023) · Materials at High Temperatures · doi:10.1080/09603409.2022.2138007 · Cited by 8
“It is anticipated from literature [15,17,20,21], that a mixed deposit chemistry will decrease the melting”
BackgroundSahadevan, P., Selvan, C. P., Chandrashekarappa, M. P. G., & Bhaumik, A. (2023) · Archives of Foundry Engineering · doi:10.24425/afe.2023.146685 · Cited by 8
“Iron and its alloys (in particular low alloyed steels) are more susceptible to corrosion and often available at relatively low cost [11].”
BackgroundLindmark, H., Jonsson, T., & Liske, J. (2024) · Corrosion Science · doi:10.1016/j.corsci.2024.111843 · Cited by 8
Self-citationMa, W., Zeng, S., & Wenga, T. (2024) · Corrosion Science · doi:10.1016/j.corsci.2024.112128 · Cited by 8
Comparison between oxidation of Fe–Cr–Al sputter coatings in air and air–HCl environments at 550°C
Orlicka, D., Simms, N. J., Hussain, T., & Nicholls, J. R. (2015) · Materials at High Temperatures · doi:10.1179/0960340914z.00000000095 · Cited by 8
“Unfortunately, it is also true that higher fireside corrosion rates exist in plants co-firing high levels of biomass with coal, than in conventional fossil fuel power plants.(1,2,4,5) The biomass combustion environment is rich in gaseous HCl, alkali metals, calcium, oxygen, CO2 and water vapour, but the SOx content is…”
BackgroundChange of Oxidation Mechanisms by Laser Chemical Machined Rim Zone Modifications of 42CrMo4 Steel
Schupp, A., Pütz, R. D., Beyß, O., Beste, L.-H., Radel, T., & Zander, D. (2021) · Materials · doi:10.3390/ma14143910 · Cited by 7
Larsson, E. (2017) · Chalmers Research (Chalmers University of Technology) · Cited by 7
Mortazavi, N., Intiso, L., Israelsson, N., Johansson, L., & Halvarsson, M. (2015) · CORROSION · doi:10.5006/1874 · Cited by 7
Self-citationJafarikhorami, H. (2021) · Journal of Composites and Compounds · doi:10.52547/jcc.3.2.3 · Cited by 6
The potential of SO2 for reducing corrosion in WtE plants
Hunsinger, H., & Andersson, S. (2014) · Journal of Material Cycles and Waste Management · doi:10.1007/s10163-014-0271-9 · Cited by 6
Reducing High Temperature Corrosion when Burning Waste by Adding Digested Sewage Sludge
Karlsson, S., Åmand, L.-E., & Pettersson, J. (2011) · Chalmers Publication Library (Chalmers University of Technology) · Cited by 6
Wu, D., Wu, H., Yuan, Z., Zheng, J., Wei, X., & Zhang, C. (2022) · Journal of Thermal Spray Technology · doi:10.1007/s11666-022-01451-8 · Cited by 6
Effect of High-Temperature Corrosion on the Service Life of P91 Piping in Biomass Co-firing
O’Hagan, C. P., Barrett, R. A., Leen, S. B., & Monaghan, R. F. D. (2016) · Journal of Pressure Vessel Technology · doi:10.1115/1.4032648 · Cited by 6
Karlsson, S. (2015) · Chalmers Research (Chalmers University of Technology) · Cited by 6
Effect of temperature on corrosion of furnace walls in a waste wood fired boiler
Alipour, Y., Henderson, P., & Szakálos, P. (2015) · Materials at High Temperatures · doi:10.1179/0960340914z.000000000100 · Cited by 5
“A number of laboratory studies have shown that KCl is very corrosive.(4,28,29) Therefore, it was possible to correlate this high corrosion rate with the chemical composition of the deposit.”
BackgroundLehmusto, J., Olin, M., Viljanen, J., Kalliokoski, J., Mylläri, F., Toivonen, J., Maso, M. D., & Hupa, L. (2019) · Materials and Corrosion · doi:10.1002/maco.201910964 · Cited by 5
Andersson, S., Paz, M. D., Phother-Simon, J., & Jonsson, T. (2018) · Detritus · doi:10.31025/2611-4135/2019.13784 · Cited by 5
Self-citationOgaz, M. A. O. (2019) · Chalmers Research (Chalmers University of Technology) · Cited by 5
Initial corrosion attack of 304L and T22 in 2 MW biomass gasifier: a microstructural investigation
Hooshyar, H., Liske, J., Johansson, L., Seemann, M. C., & Jonsson, T. (2015) · Materials at High Temperatures · doi:10.1179/0960340914z.000000000101 · Cited by 5
Self-citationFurnace Wall Corrosion in a Wood-fired Boiler
Alipour, Y. (2015) · DiVA (Digitala Vetenskapliga Arkivet) · Cited by 5
The initial effect of KCl deposit on alumina scales characterized by ToF‐SIMS and AES
Engkvist, J., Israelsson, N., & Bexell, U. (2012) · Surface and Interface Analysis · doi:10.1002/sia.5081 · Cited by 4
Changes in chlorine content over time – Probe deposit sampling in a Finnish kraft recovery boiler
Balint, R., Engblom, M., Vainio, E., Laurén, T., Niemi, J., Rautala, J., Saarinen, T., Hupa, M. M., & Hupa, L. (2023) · Fuel · doi:10.1016/j.fuel.2023.127599 · Cited by 4
Okoro, S. C., Nießen, F., Villa, M., Apel, D., Montgomery, M., Frandsen, F., & Pantleon, K. (2016) · Metallography Microstructure and Analysis · doi:10.1007/s13632-016-0325-6 · Cited by 4
Li, Y., Li, Y., Zhang, Y., Li, J., Xu, J., Li, M., & Zhao, G. (2024) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2024.177593 · Cited by 3
Usman, A., Isern, L., Nicholls, J. R., Cordero-Cabrera, M. C., & Syed, A. U. (2025) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-025-11630-7 · Cited by 3
Phother-Simon, J. (2019) · Chalmers Research (Chalmers University of Technology) · Cited by 3
Hamdy, E., Pochi, A., & Geers, C. (2023) · Engineering Failure Analysis · doi:10.1016/j.engfailanal.2023.107332 · Cited by 3
Zhou, H., Xia, Z. D., Li, Z., & Guo, F. (2013) · Materials and Corrosion · doi:10.1002/maco.201206972 · Cited by 3
Enhanced sylvite flotation performance through ethanol-assisted interface regulation
Yuan, Y., Zhang, W., Huang, Y., Yi, H., Song, S., Liu, Q., Sun, C., Li, S., & Jia, F. (2025) · Minerals Engineering · doi:10.1016/j.mineng.2025.109927 · Cited by 2
Effects of the Different Solid Deposits on the Corrosion Behavior of Pure Fe in Water Vapor at 500°C
Tang, Y., Shen, X., Liu, Z., & Li, Y. (2020) · Scanning · doi:10.1155/2020/6280725 · Cited by 2
“[7] proposed a new mechanism as follows.”
Fireside performance of different coatings in biomass power plant
Mori, S., Pidcock, A., Sumner, J., Simms, N. J., & Oakey, J. E. (2023) · Materials at High Temperatures · doi:10.1080/09603409.2023.2188351 · Cited by 2
“Another behaviour observed in the literature [39] is also the formation of Fe-Cl complex, which could have helped the diffusion of Fe from the alloy to form Fe-rich oxide at the gas–scale interface.”
BackgroundSsenteza, V., Olausson, M. D. P., Eklund, J., Nockert, J., Liske, J., & Jonsson, T. (2025) · Energy & Fuels · doi:10.1021/acs.energyfuels.4c04806 · Cited by 1
Self-citationFailure analysis on superheater tubes of waste heat boiler in acrylic acid and ester unit
Chen, H., Huang, Y., Li, Y., Li, Y., Feng, Z., Nong, J., Guan, C., & Zhang, X. (2025) · Engineering Failure Analysis · doi:10.1016/j.engfailanal.2025.109868 · Cited by 1
Effect of KCl on high‐temperature corrosion of low‐alloyed steel under low oxygen partial pressure
Núñez, A. M., & Norling, R. (2024) · Materials and Corrosion · doi:10.1002/maco.202414314 · Cited by 1
Chen, W., Liu, L., Cui, Y., Liu, R., Ke, P., & Wang, F. (2026) · npj Materials Degradation · doi:10.1038/s41529-026-00743-6 · Cited by 1
NaCl- and CaCl2-Induced High Temperature Corrosion of Automotive Exhaust Components
Vidic, K., Mori, G., Yasir, M., & Knoll, D. (2018) · NACE CORROSION Conference · doi:10.5006/c2018-11303 · Cited by 1
Beyond Breakaway Corrosion: Secondary Corrosion Protection of Iron-based Alloys
Persdotter, A. (2020) · Chalmers Research (Chalmers University of Technology) · Cited by 1
High Temperature Corrosion of Stainless Steels - The Effects of Chloride Salts and SO2(g)
Karlsson, S. (2011) · Chalmers Publication Library (Chalmers University of Technology) · Cited by 1
Experimental and numerical characterisation of materials for biomass co-firing
O’Hagan, C. P. (2017) · Arrow@dit (Dublin Institute of Technology) · doi:10.13025/16702 · Cited by 1
The role and corrosivity of lead in recycled wood combustion
Kinnunen, H. (2019) · Doria (University of Helsinki) · Cited by 1
Talus, A. (2016) · Chalmers Research (Chalmers University of Technology)
Deposition Properties of Biomass Fly Ash
Laxminarayan, Y., Jensen, P. A., Wang, G., Wu, H., Sander, B., Frandsen, F., & Glarborg, P. (2018) · Technical University of Denmark, DTU Orbit (Technical University of Denmark, DTU) · doi:10.5071/26theubce2018-2ao.8.2
Effects of Temperature Gradient on Ash Deposit Aging and Heat Exchanger Corrosion
Niemi, J. (2019) · Doria (University of Helsinki)
Metadata
- Authors
- Folkeson, N., Jonsson, T., Halvarsson, M., Johansson, L. ‐., & Svensson, J. ‐.
- Affiliations
- Chalmers University of Technology (SE)
- Corresponding author
- Jonsson, T.
- Venue
- Materials and Corrosion
- Publisher
- Wiley
- Published
- 2010-12-23
- Volume
- 62
- Issue
- 7
- Pages
- 606-615
- ISSN
- 0043-2822 (ISSN-L)
- 0947-5117
- 1521-4176
- OpenAlex
- W2073148583
- Cited by
- 93
- References
- 29
- Citations by year
- 2026: 2 · 2025: 5 · 2024: 7 · 2023: 7 · 2022: 11 · 2021: 5 · 2020: 4 · 2019: 14 · 2018: 5 · 2017: 5 · 2016: 5 · 2015: 10 · 2014: 5 · 2013: 3 · 2012: 2
- FWCI
- 5.02
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Materials and Corrosion (publishedVersion)
- Chalmers Research (Chalmers University of Technology) (submittedVersion)
- Topics
- Physical Sciences › Materials Science › Surfaces, Coatings and Films › High-Temperature Coating Behaviors
- Physical Sciences › Engineering › Mechanical Engineering › High Temperature Alloys and Creep
- Physical Sciences › Materials Science › Materials Chemistry › Material Properties and Failure Mechanisms
- Keywords
- high-temperature corrosion, potassium chloride, chloride-induced corrosion, low-alloy steel, oxidation, mass gain, flue gas, water vapor, temperature dependence
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.