The DOI matches its Crossref record; 15 of the 15 references it cites were found in a registry or an index.
Experimental study of frost accumulation on fan-supplied tube-fin evaporators
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“In experimental tests, frost mass is typically estimated using the humidity ratio difference between the inlet and the outlet, as demonstrated in [17] and [20].”
In the citing paper
“In addition, most experimental tests have been con ducted on horizontally assembled plates [12 -17] or fin-and-tube heat exchangers under horizontal air flow conditions [18 -21].”
In the citing paper
“The frost layer and air-side pressure drop have a strong relationship [34].”
From Experimental investigation on an air source heat pump system with a novel anti-frosting evaporator (2023) · cites this paper as [34]
In the citing paper
“Figure 5 compares the time evolution of the calculated cooling capacity (Fig. 5a) and air flow rate (Fig. 5b) with the experimental counterparts, where one can note that the model is able to follow the experimental trends quite satisfactorily, especially after the early transients (i.e., from 10 min on), where the frost formation effects are more perceptible”
From Optimal design of fan-supplied tube-fin evaporators subjected to frosting conditions aiming at minimum energy consumption (2018) · cites this paper as [26]
In the citing paper
“The model validation exercise for the frosting evaporator was carried out using data from [26].”
From Optimal design of fan-supplied tube-fin evaporators subjected to frosting conditions aiming at minimum energy consumption (2018) · cites this paper as [26]
In the citing paper
“Another real-time measuring method for the total frost accumulation is calculating with the changing of air water content at inlet and outlet air of the outdoor heat exchanger, or evaporator [127].”
From Review on the measurement and calculation of frost characteristics (2018) · cites this paper as [127]
In the citing paper
“Some experimental results showed the louver fin had the most frost accumulation amount and the greatest air pressure drop, followed the wavy and flat fins.”
From Effect of fin types of outdoor fan-supplied finned-tube heat exchanger on periodic frosting and defrosting performance of a residential air-source heat pump (2014) · cites this paper as Silva and Hermes [1]
In the citing paper
“Under certain outdoor winter conditions, frost forms on the outdoor finned-tube heat exchanger and decreases its thermal performance due to the combined effects of the increased thermal resistance and the decreased airflow rate caused by frost blocking.”
Citations
Cites
Thermal environmental engineering
(1962) · Journal of the Franklin Institute · doi:10.1016/0016-0032(62)90922-5 · Cited by 927
A study of frost growth and densification on flat surfaces
Hermes, C. J. L., Piucco, R. O., Barbosa, J. R., & Melo, C. (2009) · Experimental Thermal and Fluid Science · doi:10.1016/j.expthermflusci.2008.10.006 · Cited by 257 · cited 1×
“…frost mass. Supercooling levels (i.e., the temperature difference between the evaporator surface and the dew-point of the entering air flow, see Hermes et al., 2009) of 3.5, 5.0, 10.0 and 14.5°C were used in combination with different air flow rates and evaporator geometries (i.e., different…”
MethodInfluentialSelf-citationXia, Y., Zhong, Y., Hrnjak, P. S., & Jacobi, A. M. (2006) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2006.03.005 · Cited by 152 · cited 1×
“In a first attempt to fill this gap, Xia et al. (2006) studied the frosting, defrosting and re-frosting processes taking place on louvered-fin flat-tube heat exchangers and observed that the overall heat transfer coefficient decreases due to the reduction in the air flow rate and also to the…”
BackgroundEffect of surface treatments on the frosting/defrosting behavior of a fin-tube heat exchanger
Jhee, S., Lee, K.-S., & Kim, W.-S. (2002) · International Journal of Refrigeration · doi:10.1016/s0140-7007(02)00008-7 · Cited by 149
Seker, D., Karatas, H., & Egrican, N. (2004) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2003.12.003 · Cited by 147
Fin spacing optimization of a fin-tube heat exchanger under frosting conditions
Yang, D.-K., Lee, K.-S., & Song, S. (2006) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2006.01.016 · Cited by 81
Zhang, P., & Hrnjak, P. S. (2009) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2008.11.006 · Cited by 75
Fan supplied heat exchanger fin performance under frosting conditions
Chen, H., Thomas, L., & Besant, R. W. (2003) · International Journal of Refrigeration · doi:10.1016/s0140-7007(02)00011-7 · Cited by 59
Lenic, K., Trp, A., & Frankovic, B. (2009) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2008.12.030 · Cited by 38
Bejan, A., Vargas, J. V. C., & Lim, J. S. (1994) · International Journal of Heat and Mass Transfer · doi:10.1016/0017-9310(94)90087-6 · Cited by 33
Research works printed but not linked: 4
- Stoecker, 1957, How frost formation on coils affects refrigeration systems, Refrigerating Engineering, 65
- Kondepudi, 1987, The effect of frost growth on extended surface heat exchanger performance: a review, ASHRAE Transactions, 93, 258
- Rite, 1991, The effect of frost accumulation on the performance of domestic refrigerator-freezer finned-tube evaporator coils, ASHRAE Transactions, 97, 428
- Ogawa, 1993, Performance improvement of plate fin-and-tube heat exchangers under frosting conditions, ASHRAE Transactions, 99, 762
Cited by
Sorted by citations
Review on improvement for air source heat pump units during frosting and defrosting
Song, M., Deng, S., Dang, C., Mao, N., & Wang, Z. (2018) · Applied Energy · doi:10.1016/j.apenergy.2017.12.022 · Cited by 384
Review on the measurement and calculation of frost characteristics
Song, M., & Dang, C. (2018) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2018.03.094 · Cited by 212
Frosting characteristics on hydrophobic and superhydrophobic surfaces: A review
Kim, M.-H., Kim, H., Lee, K.-S., & Kim, D. R. (2017) · Energy Conversion and Management · doi:10.1016/j.enconman.2017.01.067 · Cited by 171
Tang, J., Gong, G., Su, H., Wu, F., & Herman, Č. (2016) · Applied Energy · doi:10.1016/j.apenergy.2016.02.042 · Cited by 122
State-of-the-art review of frost deposition on flat surfaces
Léoni, A., Mondot, M., Durier, F., Revellin, R., & Haberschill, P. (2016) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2016.04.004 · Cited by 103
Huang, D., Ri-Jing, Z., Liu, Y., & Yi, D.-B. (2014) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2013.11.052 · Cited by 99
Song, M., Mao, N., Xu, Y.-J., & Deng, S. (2019) · Thermal Science and Engineering Progress · doi:10.1016/j.tsep.2019.03.002 · Cited by 85
Continuous heating of an air-source heat pump during defrosting and improvement of energy efficiency
Jang, J. Y., Bae, H. H., Lee, S. J., & Ha, M. Y. (2013) · Applied Energy · doi:10.1016/j.apenergy.2013.04.030 · Cited by 92
Wang, W., Xiao, J., Feng, Y., Guo, Q., & Wang, L.-C. (2013) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2012.06.019 · Cited by 83
Bacellar, D., Aute, V., Huang, Z., & Radermacher, R. (2017) · Science and Technology for the Built Environment · doi:10.1080/23744731.2017.1333877 · Cited by 75
Influence of Outdoor Air Conditions on the Air Source Heat Pumps Performance
Vocale, P., Morini, G. L., & Spiga, M. (2014) · Energy Procedia · doi:10.1016/j.egypro.2014.01.070 · Cited by 85
Experimental study of frost formation on cold surfaces with various fin layouts
Wu, X., Hu, S., & Chu, F. (2016) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2015.11.045 · Cited by 72
First-principles modeling of frost accumulation on fan-supplied tube-fin evaporators
da Silva, D. L., Hermes, C. J. L., & Melo, C. (2011) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2011.04.029 · Cited by 70
Self-citationKnabben, F. T., Hermes, C. J. L., & Melo, C. (2011) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2011.07.006 · Cited by 67
Self-citationZhang, L., Jiang, Y., Dong, J., Yao, Y., & Deng, S. (2019) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2018.09.016 · Cited by 65
Effect of frost morphology on the thermal-hydraulic performance of fan-supplied tube-fin evaporators
da Silva, D. L., Melo, C., & Hermes, C. J. L. (2017) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2016.09.165 · Cited by 58
Self-citationZhang, L., Jiang, Y., Dong, J., Yao, Y., & Deng, S. (2018) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2017.12.047 · Cited by 56
Ma, L., Sun, Y., Wang, F., Wang, M., Zhang, S., & Wang, Z. (2025) · Applied Energy · doi:10.1016/j.apenergy.2024.124358 · Cited by 54
Song, M., Fan, C., Mao, N., & Xu, Y. (2018) · Energy and Buildings · doi:10.1016/j.enbuild.2018.08.027 · Cited by 51
Transient model of a vertical freezer with door openings and defrost effects
Mastrullo, R., Mauro, A. W., Menna, L., Palma, A., & Vanoli, G. (2014) · Applied Energy · doi:10.1016/j.apenergy.2014.01.069 · Cited by 45
Liu, X., Yu, J., & Yan, G. (2020) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2019.114634 · Cited by 47
Song, M., Wang, Z.-H., Mao, N., Dong, J.-K., & Zhang, H.-R. (2019) · Sustainable cities and society · doi:10.1016/j.scs.2019.101461 · Cited by 43
Klingebiel, J., Salamon, M., Bogdanov, P., Venzik, V., Vering, C., & Müller, D. (2023) · Energy and Buildings · doi:10.1016/j.enbuild.2023.113397 · Cited by 32
Zhang, L., Jiang, Y., Dong, J., Yao, Y., & Deng, S. (2019) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2019.114063 · Cited by 40
Zhang, L., Song, M., Mao, N., & Dong, J. (2022) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2021.122192 · Cited by 38
Kim, J., Jeon, J., Kim, D. R., & Lee, K.-S. (2018) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2018.06.023 · Cited by 35
Frosting in heat pump evaporators part A: experimental investigation
Reichl, C., Sandström, C., Hochwallner, F., Linhardt, F., Popovac, M., & Emhofer, J. (2021) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2021.117487 · Cited by 34
Simulation of a multi-source hybrid heat pump system with seasonal thermal storage in cold regions
Han, Z., Qu, L., Ma, X., Song, X., & Ma, C. (2017) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2017.01.057 · Cited by 33
Research on defrost free air-source heat pump with surface stripe concavo-convex fins
Yajima, T., OHKUBO, H., & Seki, M. (2020) · Energy and Buildings · doi:10.1016/j.enbuild.2020.110568 · Cited by 32
Optical investigation of cryogenic frost formation under forced convection
Jeong, H., Byun, S., Kim, D. R., & Lee, K.-S. (2022) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2021.117887 · Cited by 32
A Critical Literature Review of Defrost Technologies for Heat Pumps and Refrigeration Systems
Nawaz, K., Elatar, A., & Fricke, B. A. (2018) · doi:10.2172/1474464 · Cited by 31
Eguiarte, O., Garrido-Marijuán, A., de Agustín-Camacho, P., del Portillo, L. A., & Romero-Amorrortu, A. (2020) · Energies · doi:10.3390/en13153939 · Cited by 30
Experimental investigation on an air source heat pump system with a novel anti-frosting evaporator
Yu, S., Su, Y., Cai, W., & Qiu, G. (2023) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2022.119910 · Cited by 29
Sarmiento, A. P., de Sá Sarmiento, F. I. P., Shooshtari, A., & Ohadi, M. (2024) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2024.123680 · Cited by 29
Evaporator Frosting in Refrigerating Appliances: Fundamentals and Applications
Hermes, C. J. L., Boeng, J., Silva, D. L. D., Knabben, F. T., & Sommers, A. D. (2021) · Energies · doi:10.3390/en14185991 · Cited by 31
Self-citationZhao, R., Huang, D., Peng, X., & Yang, H. (2018) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2018.12.003 · Cited by 26
Real-time frost porosity detection using capacitance sensing approach
Shen, Y., & Wang, X.-F. (2019) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2019.02.060 · Cited by 26
Simulation study on performance of a dual-source hybrid heat pump unit with alternative refrigerants
Bai, C., Han, Z.-W., Wei, H.-T., Ju, X., Meng, X., & Fu, Q. (2020) · Energy and Built Environment · doi:10.1016/j.enbenv.2019.08.004 · Cited by 24
Effect of heat transfer area distribution on frosting performance of refrigerator evaporator
Pegallapati, A. S., & Ramgopal, M. (2021) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2021.121317 · Cited by 26
Abbas, S., & Park, C. (2021) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2020.120883 · Cited by 25
Flat tube heat exchangers: Experimental analysis of frosting and water retention
Westhaeuser, J., Brauchle, L., Albrecht, J.-C., Tegethoff, W., Lemke, N., & Koehler, J. (2023) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2022.119319 · Cited by 24
Liu, S., Bai, X.-S., Deng, S., Zhang, L., & Wei, M. (2023) · Energy and Buildings · doi:10.1016/j.enbuild.2023.113049 · Cited by 22
Optimal defrost cycle for air coolers revisited: A study of fan-supplied tube-fin evaporators
da Silva, D. L., & Hermes, C. J. L. (2018) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2018.02.009 · Cited by 22
Self-citationExperimental study of the characteristic of frosting on low-temperature air cooler
Haijie, Q., Li, W., Bo, D., Zhihai, Z., & Weiying, Z. (2014) · Experimental Thermal and Fluid Science · doi:10.1016/j.expthermflusci.2014.02.021 · Cited by 22
Zhu, Z., Dou, W., Dai, B., Shan, X., & Shen, J. (2023) · Case Studies in Thermal Engineering · doi:10.1016/j.csite.2023.102922 · Cited by 21
Power optimization for defrosting heaters in household refrigerators to reduce energy consumption
Jeong, H., Byun, S., Kim, D. R., & Lee, K.-S. (2021) · Energy Conversion and Management · doi:10.1016/j.enconman.2021.114127 · Cited by 20
Control strategies for defrost and evaporator fans operation in walk-in freezers
Maldonado, J., Zsembinszki, G., de Gracia, Á., Moreno, P., Albets, X., Gonzalez, M., & Cabeza, L. (2018) · International journal of refrigeration · doi:10.1016/j.ijrefrig.2018.05.025 · Cited by 20
Ribeiro, R. S., & Hermes, C. J. L. (2014) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2014.05.012 · Cited by 19
Self-citationKlingebiel, J., Höges, C., Göbel, S., Bannmüller, P., Boelsen, T., Venzik, V., Vering, C., & Müller, D. (2025) · Energy · doi:10.1016/j.energy.2025.135871 · Cited by 17
An experimental study on a novel defrosting method for cold room
Abdulla, M. O. A., Deniz, E., Karagöz, M., & Gürüf, G. (2021) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2021.116573 · Cited by 17
Frost detection method on evaporator in vapour compression systems
Maldonado, J., de Gracia, Á., Zsembinszki, G., Moreno, P., Albets, X., Gonzalez, M., & Cabeza, L. (2020) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2019.10.023 · Cited by 15
Analysis of the heat transfer area distribution in a frosted plain fin-and-tube geometry
Morales-Fuentes, A., Chapa-Contreras, O. M., Méndez-Díaz, S., & Belman-Flores, J. (2017) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2017.01.016 · Cited by 15
Liao, C., Zeng, L., Long, J., & Yongga, A. (2022) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2022.119684 · Cited by 15
Control-oriented hybrid model of a small-scale refrigerated truck chamber
Fallmann, M., Poks, A., & Kozek, M. (2022) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2022.119719 · Cited by 15
Xing, H., Fan, W., Qu, M.-L., Chen, J.-B., & Chen, Q.-H. (2014) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2014.03.011 · Cited by 14
Liu, S., Bai, X., Deng, S., Zhang, L., & Wei, M. (2022) · Journal of Building Engineering · doi:10.1016/j.jobe.2022.104990 · Cited by 15
Klingebiel, J., Höges, C., Horst, J., Nießen, O., Venzik, V., Vering, C., & Müller, D. (2025) · Applied Energy · doi:10.1016/j.apenergy.2025.126400 · Cited by 14
Image recognition method for frost sensing applications
Aguiar, M., Gaspar, P., & da Silva, P. D. (2022) · Energy Reports · doi:10.1016/j.egyr.2022.01.049 · Cited by 13
Gendebien, S., Parthoens, A., & Lemort, V. (2019) · Energy and Buildings · doi:10.1016/j.enbuild.2018.12.039 · Cited by 15
Effects of inclination on the frosting process on cold surface of copper heat exchanger
Chen, A., Meng, Y., Liu, B., Li, Y., & Miao, Z. (2021) · Energy and Buildings · doi:10.1016/j.enbuild.2020.110628 · Cited by 14
Babadi, M. N., Cho, Y., Kang, S., & Yeom, E. (2025) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2025.127293 · Cited by 13
Fei, W., Zhao, R., Xu, W., Huang, D., & Qu, Z. (2021) · Energies · doi:10.3390/en14092646 · Cited by 13
Heidinger, G. G., do Nascimento, S. M., Gaspar, P. D., & da Silva, P. D. (2018) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2018.04.038 · Cited by 13
Literature Review of Frost Formation Phenomena on Domestic Refrigerators Evaporators
Krasota, D., Błasiak, P., & Kolasiński, P. (2023) · Energies · doi:10.3390/en16072945 · Cited by 13
Capacitive sensing of frost growth dynamics on aluminum surfaces with different wettabilities
Inanlu, M., Gurumukhi, Y., Kabirzadeh, P., Anand, R., Khodakarami, S., Viswanathan, V., Stillwell, A., & Miljković, N. (2024) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2024.125377 · Cited by 10
Oliveira, A. V. D. S., Stemmelen, D., Leclerc, S., Glantz, T., Labergue, A., Repetto, G., & Gradeck, M. (2021) · Experimental Thermal and Fluid Science · doi:10.1016/j.expthermflusci.2021.110383 · Cited by 12
Harrington, L., Aye, L., & Fuller, B. (2017) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2017.12.002 · Cited by 12
Model-based estimation of cold room temperatures in a supermarket refrigeration system
O’Neill, Z. D., & Narayanan, S. (2014) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2014.08.038 · Cited by 11
Ambient virtual sensor based defrost control for single compartment refrigerators
Vitor, M. F., Silveira, A. D. S., & Flesch, R. C. C. (2019) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2019.114652 · Cited by 11
Thermal performance of peripheral-finned tube evaporators under frosting
Timmermann, M., Kaviany, M., & Barbosa, J. (2018) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2017.09.008 · Cited by 12
Passarelli, A. F., Merlo, U., Pelella, F., Viscito, L., Filippini, S., & Mauro, A. W. (2025) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2025.128790 · Cited by 9
Citarella, B., Viscito, L., Mochizuki, K., & Mauro, A. W. (2022) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2022.118796 · Cited by 9
Ghaddar, D., Boyina, K., Chettiar, K., Hoque, M. J., Baker, M., Bhalerao, P., Reagen, S., & Miljković, N. (2023) · Applied Physics Letters · doi:10.1063/5.0157647 · Cited by 10
Juhola, V., Mikkola, V., Inkeri, E., Kabelac, S., & Tynjälä, T. (2025) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2025.127396 · Cited by 9
Wang, J., Wang, J., Xie, L., Peng, F., & Shi, L. (2024) · International Communications in Heat and Mass Transfer · doi:10.1016/j.icheatmasstransfer.2024.107415 · Cited by 9
Time scaling of frost accretion and the square-root-of-time rule
Hermes, C., Sommers, A., & Barbosa, J. (2019) · International Communications in Heat and Mass Transfer · doi:10.1016/j.icheatmasstransfer.2019.104281 · Cited by 8
Self-citationRohani, H., & Woo, P. C. (2023) · International Communications in Heat and Mass Transfer · doi:10.1016/j.icheatmasstransfer.2023.106992 · Cited by 8
Investigation on thermal-hydraulic performance of outdoor heat exchanger in air sources heat pump
Fang, Z., Li, L., Cheng, Y. C., Wang, P., & Oladokun, M. O. (2017) · Experimental Thermal and Fluid Science · doi:10.1016/j.expthermflusci.2017.01.008 · Cited by 7
Aguiar, M., Gaspar, P., & Silva, P. D. (2023) · Italian National Conference on Sensors · doi:10.3390/s23115253 · Cited by 4
Medium materials for improving frost detection on a resistive sensor
Aguiar, M., Gaspar, P., Silva, P. D., Silva, A. P., & Martinez, A. M. (2020) · Energy Reports · doi:10.1016/j.egyr.2020.11.258 · Cited by 7
Mahdavi, M., & Yaghoubi, M. A. (2011) · Heat Transfer-Asian Research · doi:10.1002/htj.20397 · Cited by 6
Quick estimation of frost growth on cold fins through thermal network analysis
Kim, S., & Lee, S.-Y. (2014) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2014.07.015 · Cited by 6
Chen, M., Ge, X., Zheng, H., Song, M., Sheng, W., Chen, X., Fu, D., & Dang, C. (2025) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2025.127205 · Cited by 6
Experimental study about frost formation and growth in the evaporator of an air-to-water heat pump
Gallén, D. A., Marchante-Avellaneda, J., Hassan, A. H., & Navarro-Peris, E. (2025) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2025.08.013 · Cited by 5
İpek, M., & Dinçer, İ. (2023) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2023.06.004 · Cited by 5
Li, J., Long, J., Tan, X., & Zhang, R. (2024) · Advances in Building Energy Research · doi:10.1080/17512549.2024.2365944 · Cited by 5
Zhao, R., Huang, D., Peng, X., & Yang, H. (2019) · Science and Technology for the Built Environment · doi:10.1080/23744731.2019.1665445 · Cited by 5
Frost Formation on Fan-Supplied Tube-Fin Evaporators: A Visual and Numerical Analysis
Silva, D. L. D. (2012) · Purdue e-Pubs (Purdue University System) · Cited by 5
Boeng, J., & Stahelin, R. (2025) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2025.127327 · Cited by 6
İpek, M., & Dinçer, İ. (2024) · Thermal Science and Engineering Progress · doi:10.1016/j.tsep.2024.102665 · Cited by 4
Braun, L., Reis, R. G., Nascimento, C. A. R., Silveira, A. S., & Hermes, C. J. L. (2025) · Thermo · doi:10.3390/thermo5030032 · Cited by 4
Self-citationA sustainable defrosting technology for air source heat pump systems
Zhang, L., Wu, L., Jiang, J., Song, M., Zhang, X., Shao, K., Han, S., & Jiang, Y. (2025) · Elsevier eBooks · doi:10.1016/b978-0-443-15495-9.00010-1 · Cited by 2
Moerman, F. T., & Fikiin, K. A. (2015) · Advances in mechatronics and mechanical engineering (AMME) book series · doi:10.4018/978-1-4666-8398-3.ch014 · Cited by 2
Moerman, F. T., & Fikiin, K. A. (2015) · Advances in mechatronics and mechanical engineering (AMME) book series · doi:10.4018/978-1-4666-8398-3.ch018 · Cited by 2
de Aguiar, M. L., Gaspar, P. D., & da Silva, P. D. (2024) · Sensors · doi:10.3390/s24248193 · Cited by 2
Frost Measuring and Prediction Systems for Demand Defrost Control
de Aguiar, M. L., Gaspar, P., & da Silva, P. D. (2019) · Novel Technologies and Systems for Food Preservation · doi:10.4018/978-1-5225-7894-9.ch002 · Cited by 3
Frost Measurement Sensors for Demand Defrost Control Systems: Purposed Applications in Evaporators
de Aguiar, M. L., Gaspar, P., & da Silva, P. D. (2019) · Transactions on Engineering Technologies · doi:10.1007/978-981-32-9531-5_12
Leoni, A. (2017) · theses.fr (ABES) · doi:10.70675/f052b4afz1f26z4ed9zbeaez6d56015b3f69 · Cited by 2
Ribeiro, R. S., da Silva, D. L., & Hermes, C. J. L. (2018) · Journal of the Brazilian Society of Mechanical Sciences and Engineering · doi:10.1007/s40430-018-1401-4 · Cited by 1
Self-citationThermoelectric-Powered Remote Sensor for Frost Detection
de Aguiar, M. L., Gaspar, P., & da Silva, P. D. (2024) · Electronics · doi:10.3390/electronics13142683 · Cited by 1
Metadata
- Authors
- da Silva, D. L., Hermes, C. J. L., & Melo, C.
- Affiliations
- Universidade Federal do Paraná (BR)
- Universidade Federal de Santa Catarina (BR)
- Corresponding author
- Hermes, Christian J.L.
- ORCID
- Melo, Claudio
- Venue
- Applied Thermal Engineering
- Publisher
- Elsevier BV
- Published
- 2011-05
- Volume
- 31
- Issue
- 6-7
- Pages
- 1013-1020
- ISSN
- 1359-4311 (ISSN-L)
- OpenAlex
- W2079477035
- Cited by
- 118
- References
- 15
- Citations by year
- 2026: 5 · 2025: 13 · 2024: 11 · 2023: 10 · 2022: 8 · 2021: 10 · 2020: 4 · 2019: 14 · 2018: 10 · 2017: 10 · 2016: 4 · 2015: 3 · 2014: 9 · 2013: 2 · 2012: 2
- FWCI
- 4.26
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Applied Thermal Engineering (publishedVersion)
- Purdue e-Pubs (Purdue University System) (submittedVersion)
- Funders
- Conselho Nacional de Desenvolvimento Científico e Tecnológico
- Embraco
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Refrigeration and Air Conditioning Technologies
- Physical Sciences › Engineering › Mechanical Engineering › Heat Transfer and Optimization
- Physical Sciences › Engineering › Aerospace Engineering › Icing and De-icing Technologies
- Keywords
- frost accumulation, fan characteristics, wavy fins, louvered fins, supercooling, air-side pressure drop, cooling capacity, compact heat exchangers
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
