CoChat

The Pursuit of Shortwave Infrared-Emitting Nanoparticles with Bright Fluorescence through Molecular Design and Excited-State Engineering of Molecular Aggregates

Open access
Piwoński, Hubert, Nozue, Shuho, Habuchi, Satoshi · 2022 · ACS Nanoscience Au

The DOI matches its Crossref record; 230 of the 230 references it cites were found in a registry or an index; 100 of the 279 sources its claims cite were checked for support.

Abstract

Shortwave infrared (SWIR) fluorescence detection gradually becomes a pivotal real-time imaging modality, allowing one to elucidate biological complexity in deep tissues with subcellular resolution. The key challenge for the further growth of this imaging modality is the design of new brighter biocompatible fluorescent probes. This review summarizes the recent progress in the development of organic-based nanomaterials with an emphasis on new strategies that extend the fluorescence wavelength from the near-infrared to the SWIR spectral range and amplify the fluorescence brightness. We first introduce the most representative molecular design strategies to obtain near-infrared-SWIR wavelength fluorescence emission from small organic molecules. We then discuss how the formation of nanoparticles based on small organic molecules contributes to the improvement of fluorescence brightness and the shift of fluorescence to SWIR, with a special emphasis on the excited-state engineering of molecular probes in an aggregate state and spatial packing of the molecules in nanoparticles. We build our discussion based on a historical perspective on the photophysics of molecular aggregates. We extend this discussion to nanoparticles made of conjugated polymers and discuss how fluorescence characteristics could be improved by molecular design and chain conformation of the polymer molecules in nanoparticles. We conclude the article with future directions necessary to expand this imaging modality to wider bioimaging applications including single-particle deep tissue imaging. Issues related to the characterization of SWIR fluorophores, including fluorescence quantum yield unification, are also mentioned.

Overview

CoChat Summary

TL;DR

This review argues that organic NIR/SWIR fluorophores can be made brighter through molecular design and excited-state engineering of molecular aggregates, especially by controlling J-aggregation, AIE/RACI/RADS, TICT suppression, counterion isolation, and conjugated-polymer chain conformation. It concludes that achieving bright organic SWIR emission above 1200 nm remains difficult because of the energy-gap law and low fluorescence quantum yields.

Key findings

  • SWIR (1000–1700 nm) imaging benefits from reduced tissue absorption and scattering compared with visible/NIR, but organic SWIR probes are limited by low Φfl; the energy-gap law causes nonradiative internal conversion to increase as emission shifts to longer wavelengths.
  • Molecular design strategies include polymethine dyes, donor–acceptor (D–A) systems, D-A-D dyes with BBT/BODIPY/squaraine acceptors, and A-D-A compounds; extending a polymethine chain by one vinylene unit gives nearly a 100 nm bathochromic shift, while water can reduce polymethine Φfl by up to threefold.
  • Aggregate and nanoparticle strategies can preserve or amplify brightness: J-aggregates can red-shift absorption/emission and narrow spectra; CzBTCz J-aggregate nanoparticles were 3.5 nm with fwhm = 27 nm and near-unity Φfl = 0.95; TT3-oCB showed fivefold brighter fluorescence in the aggregate state; THPP showed a 150-fold Φfl enhancement in nonpolar solvent and red-shifted emission to 1006 nm.
  • Pdots and dye-grafted conjugated polymers are promising for SWIR brightness: PSN Pdots enabled single-particle imaging through millimeter-thick tissue phantoms, and sub-nanosecond time-gated detection improved signal-to-background ratio by 29×; the review calls for new organic fluorophores with peak emission >1200 nm and decent Φfl.

Methods

  • Review article synthesizing literature on NIR/SWIR organic fluorophores, molecular aggregates, organic nanoparticles, and conjugated polymer nanoparticles (Pdots), with emphasis on photophysics and excited-state engineering.
  • Discusses historical molecular-aggregate photophysics, J-/H-/X-aggregate models, AIE/RIM/RACI/RADS, TICT, counterion-guided assembly, and conjugated-polymer chain conformation.
  • Performed a Φfl unification using reestablished fluorescence standards and constructed wavelength-dependent Φfl and fluorescence brightness (ε × Φfl) distributions for reported NIR/SWIR organic fluorophores (Figure 17).

Limitations

  • Stated: the energy-gap law limits bright organic emission above 1200 nm; currently only a handful of organic fluorophores show peak emission above 1200 nm with decent Φfl, and many J-aggregates, especially polymethine-based ones, have relatively low Φfl in aqueous environments.
  • Stated: characterization issues remain, including the need for fluorescence quantum yield unification in the SWIR region; hybrid organic–inorganic nanocomposites face complexity, reproducibility, and biocompatibility challenges.
  • Evident from the text: as a review, it does not report a systematic literature-search or inclusion protocol, and its conclusions rely on synthesis of prior studies rather than new primary experiments.

Model-written summary. Check it against the paper before relying on it.

Integrity signals

Registry

Crossref · 10.1021/acsnanoscienceau.1c00038

Cites

230 of 230 references verified0 citation errors · 0 not checkable

Statistics

Nothing to recompute.

Figures

Figure 1 NIR/SWIR emitting small-organic-molecule fluorescent probes based on polymethine dyes. General structure of polymethine dyes together with examples of the molecules that belong to this category. The numbers in red show peak fluorescence wavelengths of each molecule observed in an aqueous environment. The numbers in the brackets indicate the reference numbers for each molecule.
Figure 1 NIR/SWIR emitting small-organic-molecule fluorescent probes based on polymethine dyes. General structure of polymethine dyes together with examples of the molecules that belong to this category. The numbers in red show peak fluorescence wavelengths of each molecule observed in an aqueous environment. The numbers in the brackets indicate the reference numbers for each molecule.CC BY · PubMed Central
Figure 2 NIR/SWIR emitting small-organic-molecule fluorescent probes based on donor–acceptor systems. General structure of donor–acceptor dyes together with examples of the molecules that belong to this category. The numbers in red show peak fluorescence wavelengths of each molecule observed in an aqueous environment. The numbers in the brackets indicate the reference numbers for each molecule.
Figure 2 NIR/SWIR emitting small-organic-molecule fluorescent probes based on donor–acceptor systems. General structure of donor–acceptor dyes together with examples of the molecules that belong to this category. The numbers in red show peak fluorescence wavelengths of each molecule observed in an aqueous environment. The numbers in the brackets indicate the reference numbers for each molecule.CC BY · PubMed Central
Figure 3 Exciton splitting diagram for aggregates with J-aggregate, H-aggregate, X-aggregate, and AIE configurations. Reproduced with permission from ref (88), copyright 2018 Wiley-VCH Verlag GmbH & Co.
Figure 3 Exciton splitting diagram for aggregates with J-aggregate, H-aggregate, X-aggregate, and AIE configurations. Reproduced with permission from ref (88), copyright 2018 Wiley-VCH Verlag GmbH & Co.CC BY · PubMed Central
Figure 4 Fluorescent J-aggregate nanoparticles by encapsulating in nanostructures. (a) Schematic illustration to show the fabrication process of IR825@PEI–PEG/DOX (top). Absorption spectra of IR825@PEI–PEG (black) and IR825 in PEGylated micelles (red) (left). Transmission electron microscopy image of IR825@PEI–PEG. (b) Chemical structures of PCP-BDP1, PCP-BDP2, Ph-BDP1, and Ph-BDP2 (left). Fluorescence spectra of PCP-BDP2 in diluted dichloromethane (DCM) solution (10 μM) (black line, “M” refers to monomer), THF–water binary solvents (10 μM, 1:9, v/v) (red line, J1-band), and the crystalline powder (blue line, J2-band) (right). (c) Schematic illustration describing the stabilization of IR-140 J-aggregates in hollow mesoporous silica nanoparticles (HMSNs) to result in biocompatible SWIR-emissive contrast agents (left). Absorption spectra of the IR-140 monomer and J-aggregates in HMSNs (right). A washing step facilitates the J-aggregates formation. (d) Schematic illustration of the preparation of titanium plates coated with a silica layer encapsulated by SWIR emitting J-aggregates (MSTPs-FDJ@PAA). (e) Chemical structure of SQP (top). Absorption (black) and fluorescence (red) spectra of SQP in THF (left). Absorption spectra of SQP-NPs-NPs in THF (SQP-NPs(H)) and in DCM (SQP-NPs(J)) (right). (a) Reproduced with permission from ref (111), copyright 2015 Elsevier Ltd. (b) Reproduced with permission from ref (118), under CC BY 4.0. (c) Reproduced with permission from ref (114), copyright 2019 American Chemical Society. (d) Reproduced with permission from ref (115), copyright 2021 Wiley-VCH GmbH. (e) Reproduced with permission from ref (116), copyright 2018 The Royal Society of Chemistry.
Figure 4 Fluorescent J-aggregate nanoparticles by encapsulating in nanostructures. (a) Schematic illustration to show the fabrication process of IR825@PEI–PEG/DOX (top). Absorption spectra of IR825@PEI–PEG (black) and IR825 in PEGylated micelles (red) (left). Transmission electron microscopy image of IR825@PEI–PEG. (b) Chemical structures of PCP-BDP1, PCP-BDP2, Ph-BDP1, and Ph-BDP2 (left). Fluorescence spectra of PCP-BDP2 in diluted dichloromethane (DCM) solution (10 μM) (black line, “M” refers to monomer), THF–water binary solvents (10 μM, 1:9, v/v) (red line, J1-band), and the crystalline powder (blue line, J2-band) (right). (c) Schematic illustration describing the stabilization of IR-140 J-aggregates in hollow mesoporous silica nanoparticles (HMSNs) to result in biocompatible SWIR-emissive contrast agents (left). Absorption spectra of the IR-140 monomer and J-aggregates in HMSNs (right). A washing step facilitates the J-aggregates formation. (d) Schematic illustration of the preparation of titanium plates coated with a silica layer encapsulated by SWIR emitting J-aggregates (MSTPs-FDJ@PAA). (e) Chemical structure of SQP (top). Absorption (black) and fluorescence (red) spectra of SQP in THF (left). Absorption spectra of SQP-NPs-NPs in THF (SQP-NPs(H)) and in DCM (SQP-NPs(J)) (right). (a) Reproduced with permission from ref (111), copyright 2015 Elsevier Ltd. (b) Reproduced with permission from ref (118), under CC BY 4.0. (c) Reproduced with permission from ref (114), copyright 2019 American Chemical Society. (d) Reproduced with permission from ref (115), copyright 2021 Wiley-VCH GmbH. (e) Reproduced with permission from ref (116), copyright 2018 The Royal Society of Chemistry.CC BY · PubMed Central
Figure 5 Fluorescent J-aggregate nanoparticles without encapsulation. (a) Chemical structure of the CzBTCz molecule (top left). Absorption (solid lines) and fluorescence (dashed lines) spectra of CzBTCz in THF (red lines) and CzBTCz nanoparticles dispersed in water (blue lines) (top middle). Fluorescence decays obtained for CzBTCz in THF (red) and the CzBTCz nanoparticles dispersed in water (blue) (top right). Fluorescence brightness per unit volume calculated for Qdots 545 (QD545), Qdots 605 (QD605), Qdots 655 (QD655), (CzBT)n polymer dots (Pdots), and CzBTCz Jdots (Jdots) under the one-photon excitation condition (bottom left). Fluorescence images of the CzBTCz Jdots captured at time point 0 and 3600 s of continuous illumination109 (bottom middle). High-resolution TEM image of a single CzBTCz nanoparticle with corresponding fast Fourier transform (FFT) image of the region marked with a white box (bottom right). (b) Structural details (top) and fluorescent properties of aryl-substituted BODIPY dye, BDP1 (bottom). Molecular packing diagrams of BDP1 at room temperature extracted from single-crystal XRD data. Normalized photoluminescence spectra of BDP1 in solution (green curve) and microcrystalline powder state (red and gray curves).126 (c) Pictorial representation of the putative exciton migration and trapping model.125 (a) Reproduced with permission from ref (109), copyright 2021 American Chemical Society. (b) Reproduced with permission from ref (126), under CC BY 4.0. (c) Reproduced with permission from ref (125), copyright 2019 Wiley-VCH Verlag GmbH & Co.
Figure 5 Fluorescent J-aggregate nanoparticles without encapsulation. (a) Chemical structure of the CzBTCz molecule (top left). Absorption (solid lines) and fluorescence (dashed lines) spectra of CzBTCz in THF (red lines) and CzBTCz nanoparticles dispersed in water (blue lines) (top middle). Fluorescence decays obtained for CzBTCz in THF (red) and the CzBTCz nanoparticles dispersed in water (blue) (top right). Fluorescence brightness per unit volume calculated for Qdots 545 (QD545), Qdots 605 (QD605), Qdots 655 (QD655), (CzBT)n polymer dots (Pdots), and CzBTCz Jdots (Jdots) under the one-photon excitation condition (bottom left). Fluorescence images of the CzBTCz Jdots captured at time point 0 and 3600 s of continuous illumination109 (bottom middle). High-resolution TEM image of a single CzBTCz nanoparticle with corresponding fast Fourier transform (FFT) image of the region marked with a white box (bottom right). (b) Structural details (top) and fluorescent properties of aryl-substituted BODIPY dye, BDP1 (bottom). Molecular packing diagrams of BDP1 at room temperature extracted from single-crystal XRD data. Normalized photoluminescence spectra of BDP1 in solution (green curve) and microcrystalline powder state (red and gray curves).126 (c) Pictorial representation of the putative exciton migration and trapping model.125 (a) Reproduced with permission from ref (109), copyright 2021 American Chemical Society. (b) Reproduced with permission from ref (126), under CC BY 4.0. (c) Reproduced with permission from ref (125), copyright 2019 Wiley-VCH Verlag GmbH & Co.CC BY · PubMed Central
Figure 6 Conformational rigidification and fluorescence enhancement. Current models applied to explain observed fluorescence enhanced in aggregated states of π-conjugated materials; SLE: solid state luminescence enhancement (intramolecular vs intermolecular contributions and radiative vs nonradiative contributions),137 RIM: restriction of intramolecular motion,133 RACI: restricted access to a conical intersection,136 and RADS: restriction of access to a dark state.142 Reproduced with permission from refs (133, 136, 137), and (142), copyright 2016 The Royal Society of Chemistry, 2017 American Chemical Society, 2020 Elsevier Ltd., and 2019 Wiley-VCH Verlag GmbH & Co.
Figure 6 Conformational rigidification and fluorescence enhancement. Current models applied to explain observed fluorescence enhanced in aggregated states of π-conjugated materials; SLE: solid state luminescence enhancement (intramolecular vs intermolecular contributions and radiative vs nonradiative contributions),137 RIM: restriction of intramolecular motion,133 RACI: restricted access to a conical intersection,136 and RADS: restriction of access to a dark state.142 Reproduced with permission from refs (133, 136, 137), and (142), copyright 2016 The Royal Society of Chemistry, 2017 American Chemical Society, 2020 Elsevier Ltd., and 2019 Wiley-VCH Verlag GmbH & Co.CC BY · PubMed Central
Figure 7 Fluorescence enhancement in small-organic molecule-based fluorescent nanoparticles through conformational rigidification. (a) Chemical structure of cyano-substituted stilbenic dye, 1-cyano-trans-1,2-bis(4′-methylbiphenyl)-ethylene (CN-MBE) (top). Fluorescence spectra of CN-MBE in THF solution and NP suspensions (80 vol % water in THF) (bottom).96 (b) Schematic illustration of the chemical structure of a D-A-D-type molecule, TT3-oCB, and its intramolecular motions in a solution phase, which are suppressed in the aggregation state.61 (c) Molecular structures of the non-, mono-, and di-TPE substituted perylene bisimides with optimal structures of DBuBrPBI, N,N′-dibutyl-1-(4-(1,2,2-triphenyl)vinyl)phenylperylene-3,4:9,10-tetracarboxylic acid bisimide (DBuTPEPBI), and DBuDTPEPBI calculated by the semiempirical AM1 method (top). The photographs display the solution cast films of perylene bisimides shown above taken under daylight (bottom, left columns) and 365 nm UV light (bottom, right columns). Variation in Φfl of DBuTPEPBI and DBuDTPEPBI in hexane/DCM mixtures with varied hexane fraction (right). The insets show fluorescence images (taken under 365 nm UV light) of the corresponding mixtures.144 (d) Schematic illustration describing different aggregation extent of THPP in the nanoemulsion, micelle, and solid (top). Chemical structure of THPP (middle left). Normalized fluorescence spectra of THPP nanoemulsion, THPP micelle, and THPP solid (middle right). Absorption spectra of THPP in THF and THF/water = 1:9 (v/v) solution (bottom left). Fluorescence spectra of THPP in different ratios of THF/water solutions (bottom right).152 (a) Reproduced with permission from ref (96), copyright 2011 American Chemical Society. (b) Reproduced with permission from ref (61), copyright 2020 American Chemical Society. (c) Reproduced with permission from ref (144), copyright 2012 The Royal Society of Chemistry. (d) Reproduced with permission from ref (152), copyright 2020 Wiley-VCH Verlag GmbH & Co.
Figure 7 Fluorescence enhancement in small-organic molecule-based fluorescent nanoparticles through conformational rigidification. (a) Chemical structure of cyano-substituted stilbenic dye, 1-cyano-trans-1,2-bis(4′-methylbiphenyl)-ethylene (CN-MBE) (top). Fluorescence spectra of CN-MBE in THF solution and NP suspensions (80 vol % water in THF) (bottom).96 (b) Schematic illustration of the chemical structure of a D-A-D-type molecule, TT3-oCB, and its intramolecular motions in a solution phase, which are suppressed in the aggregation state.61 (c) Molecular structures of the non-, mono-, and di-TPE substituted perylene bisimides with optimal structures of DBuBrPBI, N,N′-dibutyl-1-(4-(1,2,2-triphenyl)vinyl)phenylperylene-3,4:9,10-tetracarboxylic acid bisimide (DBuTPEPBI), and DBuDTPEPBI calculated by the semiempirical AM1 method (top). The photographs display the solution cast films of perylene bisimides shown above taken under daylight (bottom, left columns) and 365 nm UV light (bottom, right columns). Variation in Φfl of DBuTPEPBI and DBuDTPEPBI in hexane/DCM mixtures with varied hexane fraction (right). The insets show fluorescence images (taken under 365 nm UV light) of the corresponding mixtures.144 (d) Schematic illustration describing different aggregation extent of THPP in the nanoemulsion, micelle, and solid (top). Chemical structure of THPP (middle left). Normalized fluorescence spectra of THPP nanoemulsion, THPP micelle, and THPP solid (middle right). Absorption spectra of THPP in THF and THF/water = 1:9 (v/v) solution (bottom left). Fluorescence spectra of THPP in different ratios of THF/water solutions (bottom right).152 (a) Reproduced with permission from ref (96), copyright 2011 American Chemical Society. (b) Reproduced with permission from ref (61), copyright 2020 American Chemical Society. (c) Reproduced with permission from ref (144), copyright 2012 The Royal Society of Chemistry. (d) Reproduced with permission from ref (152), copyright 2020 Wiley-VCH Verlag GmbH & Co.CC BY · PubMed Central
Figure 8 Counterion-guided small organic nanoparticles. (a) Schematic illustration of the self-assembly process and the structure of SMILES materials (top). The cyanostar anion receptor (CS) that binds to the PF6 ion in a 2-to-1 anionic complex spatially and electronically isolates lipophilic rhodamine R12 dyes. The successful formation of SMILES NPs was indicated by a red-transparent and highly fluorescent aqueous solution, which is in contrast to the nonfluorescent control sample without cyanostar (bottom left). The Cryo-TEM micrograph SMILES NPs showing spherical morphology and broad size distribution (25 ± 8 nm) (bottom right).158 (b) Chemical structures of the donor dye, rhodamine B octadecyl ester (R18), its counterion, tetrakis(pentafluorophenyl)borate (F5-TPB), and the acceptor dye, Cy5 dye (DiD) (top left). Schematic representation of the giant light-harvesting nanoantenna (bottom left) inside polymer NPs (right). Short-range ordering of R18 cations (green) by the F5-TPB counterion (blue) inside the PMMA-MA matrix prevents dye aggregation at short interfluorophore distances, promoting ultrafast EET with subsequent FRET to a single acceptor molecule (red).154 (c) Bright fluorescent NPs with varied fluorescence wavelengths were obtained by a high-density loading of cationic cyanine dyes (left) and their counterions (rigth) into polymer NPs.155 (a) Reproduced with permission from ref (158), copyright 2021 Wiley-VCH Verlag GmbH & Co. (b) Reproduced with permission from ref (154), copyright 2017 Macmillan Publishers Ltd., part of Springer Nature. (c) Reproduced with permission from ref (155), copyright 2017 Wiley-VCH Verlag GmbH & Co.
Figure 8 Counterion-guided small organic nanoparticles. (a) Schematic illustration of the self-assembly process and the structure of SMILES materials (top). The cyanostar anion receptor (CS) that binds to the PF6 ion in a 2-to-1 anionic complex spatially and electronically isolates lipophilic rhodamine R12 dyes. The successful formation of SMILES NPs was indicated by a red-transparent and highly fluorescent aqueous solution, which is in contrast to the nonfluorescent control sample without cyanostar (bottom left). The Cryo-TEM micrograph SMILES NPs showing spherical morphology and broad size distribution (25 ± 8 nm) (bottom right).158 (b) Chemical structures of the donor dye, rhodamine B octadecyl ester (R18), its counterion, tetrakis(pentafluorophenyl)borate (F5-TPB), and the acceptor dye, Cy5 dye (DiD) (top left). Schematic representation of the giant light-harvesting nanoantenna (bottom left) inside polymer NPs (right). Short-range ordering of R18 cations (green) by the F5-TPB counterion (blue) inside the PMMA-MA matrix prevents dye aggregation at short interfluorophore distances, promoting ultrafast EET with subsequent FRET to a single acceptor molecule (red).154 (c) Bright fluorescent NPs with varied fluorescence wavelengths were obtained by a high-density loading of cationic cyanine dyes (left) and their counterions (rigth) into polymer NPs.155 (a) Reproduced with permission from ref (158), copyright 2021 Wiley-VCH Verlag GmbH & Co. (b) Reproduced with permission from ref (154), copyright 2017 Macmillan Publishers Ltd., part of Springer Nature. (c) Reproduced with permission from ref (155), copyright 2017 Wiley-VCH Verlag GmbH & Co.CC BY · PubMed Central
Figure 9 Molecular design strategy for obtaining Pdots with bright fluorescence. (a) Controlling the fluorescence brightness of Pdots in the SWIR range by varied lengths of thiophene units. Chemical structures of the conjugated polymers thienothiophene-thiophene (TT-T), thienothiophene-bithiophene (TT-2T), and thienothiophene-terthiophene (TT-3T) (left). Red region represents the quinoid polymer backbones, and the blue region represents the electron-withdrawing carboxylic acid dodecyl ester group. Absorption spectra and fluorescence emission spectra of the three conjugated polymers at the same concentration in THF (right).173 (b) Molecular design and fluorination of CPs. Schematic illustration describing a nanoscale fluorous effect to maintain the hydrophobic interior and minimize the structural distortion of CPs in Pdots (top). The fluorination red shifts the optical spectra and enhances the fluorescence quantum yield (bottom).178 (c) Double-acceptor CPs. Synthetic route and chemical structures of three double-acceptor conjugated polymers.179 (d) Improved fluorescence brightness by controlling intramolecular vibrational relaxation. Synthetic routes of CPs and OSPs, with various doping ratios of DDB (left). Schematic diagram of the OSPs with different doping ratios of DDB, indicating a gradually enhanced SWIR fluorescence of OSPs with the increasing doping ratio of DDB (right).180 (a) Reproduced with permission from ref (173), copyright 2019 American Chemical Society. (b) Reproduced with permission from ref (178), copyright 2020 Wiley-VCH Verlag GmbH & Co. (c) Adopted with permission from ref (179), copyright 2021 The Royal Society of Chemistry. (d) Reproduced with permission from ref (180), copyright 2021 Wiley-VCH GmbH.
Figure 9 Molecular design strategy for obtaining Pdots with bright fluorescence. (a) Controlling the fluorescence brightness of Pdots in the SWIR range by varied lengths of thiophene units. Chemical structures of the conjugated polymers thienothiophene-thiophene (TT-T), thienothiophene-bithiophene (TT-2T), and thienothiophene-terthiophene (TT-3T) (left). Red region represents the quinoid polymer backbones, and the blue region represents the electron-withdrawing carboxylic acid dodecyl ester group. Absorption spectra and fluorescence emission spectra of the three conjugated polymers at the same concentration in THF (right).173 (b) Molecular design and fluorination of CPs. Schematic illustration describing a nanoscale fluorous effect to maintain the hydrophobic interior and minimize the structural distortion of CPs in Pdots (top). The fluorination red shifts the optical spectra and enhances the fluorescence quantum yield (bottom).178 (c) Double-acceptor CPs. Synthetic route and chemical structures of three double-acceptor conjugated polymers.179 (d) Improved fluorescence brightness by controlling intramolecular vibrational relaxation. Synthetic routes of CPs and OSPs, with various doping ratios of DDB (left). Schematic diagram of the OSPs with different doping ratios of DDB, indicating a gradually enhanced SWIR fluorescence of OSPs with the increasing doping ratio of DDB (right).180 (a) Reproduced with permission from ref (173), copyright 2019 American Chemical Society. (b) Reproduced with permission from ref (178), copyright 2020 Wiley-VCH Verlag GmbH & Co. (c) Adopted with permission from ref (179), copyright 2021 The Royal Society of Chemistry. (d) Reproduced with permission from ref (180), copyright 2021 Wiley-VCH GmbH.CC BY · PubMed Central
Figure 10 Improved fluorescence brightness of Pdots by introducing a twist in the polymer backbone. (a) Chemical structure of the CzBT CP. (b) Chemical structures of Cz-based D–A-type CPs with varied acceptor moieties (BT, DTBT, DPP, isoindigo, ND, and BBT). These polymers adopt a twisted conformation due to the steric hindrance between the donor and acceptor moieties caused by their bent shape. (c) Schematic illustration of the conformational state of the twisted polymer chains in solution and in Pdots.181 (d) Chemical structures of polyfluorene (PF)-based DA-type CPs that adopt a linear and planar shape (PSN and PSeN). (e) Φfl values of the Cz-based (blue) and PF-based (red) CPs in THF (open circles) and the Pdots dispersed in water (filled circles) plotted against their peak fluorescence wavelengths. Arrows highlight the change in Φfl and peak fluorescence wavelength upon the Pdots formation.182 (b, d, e) Reproduced with permission from ref (182), copyright 2020 American Chemical Society. (c) Reproduced with permission from refs (181 and 182) under CC BY 4.0 and copyright 2020 American Chemical Society.
Figure 10 Improved fluorescence brightness of Pdots by introducing a twist in the polymer backbone. (a) Chemical structure of the CzBT CP. (b) Chemical structures of Cz-based D–A-type CPs with varied acceptor moieties (BT, DTBT, DPP, isoindigo, ND, and BBT). These polymers adopt a twisted conformation due to the steric hindrance between the donor and acceptor moieties caused by their bent shape. (c) Schematic illustration of the conformational state of the twisted polymer chains in solution and in Pdots.181 (d) Chemical structures of polyfluorene (PF)-based DA-type CPs that adopt a linear and planar shape (PSN and PSeN). (e) Φfl values of the Cz-based (blue) and PF-based (red) CPs in THF (open circles) and the Pdots dispersed in water (filled circles) plotted against their peak fluorescence wavelengths. Arrows highlight the change in Φfl and peak fluorescence wavelength upon the Pdots formation.182 (b, d, e) Reproduced with permission from ref (182), copyright 2020 American Chemical Society. (c) Reproduced with permission from refs (181 and 182) under CC BY 4.0 and copyright 2020 American Chemical Society.CC BY · PubMed Central
Figure 11 Improved fluorescence brightness of Pdots by introducing a planar-twist conformation in polymer backbone. Chemical structures of pNIR-1, pNIR-2, pNIR-3, and pNIR-4 polymers and their respective ground-state geometries with the distinct dihedral angles (left). Absorption and fluorescence spectra of the polymers in THF (center). Fluorescence intensity variation of the polymers in THF/H2O mixtures with varied water fraction (right). Reproduced with permission from 183, copyright 2020 American Chemical Society.
Figure 11 Improved fluorescence brightness of Pdots by introducing a planar-twist conformation in polymer backbone. Chemical structures of pNIR-1, pNIR-2, pNIR-3, and pNIR-4 polymers and their respective ground-state geometries with the distinct dihedral angles (left). Absorption and fluorescence spectra of the polymers in THF (center). Fluorescence intensity variation of the polymers in THF/H2O mixtures with varied water fraction (right). Reproduced with permission from 183, copyright 2020 American Chemical Society.CC BY · PubMed Central
Figure 12 Improved fluorescence brightness of Pdots by antiaggregation-caused quenching and aggregation-induced emission. (a) Competition between the AIE and ACQ effects (top). The AIE polymer PBT demonstrated a remarkable increase in fluorescence intensity (QY increased from 9% in solution to 23% in Pdots). In contrast, the PTBT polymer displayed an intense ACQ effect, which resulted in low fluorescence emission after Pdot formation. Absorption and fluorescence spectra of the polymers PBT, PTBT, and PHTBT in THF (bottom left). Fluorescence intensity changes of PBT, PTBT, and PHTBT in THF/water mixtures with different water fractions (bottom right).187 (b) Chemical structures of three CPs with different donors; PF, dominated by the ACQ effect, TPE, AIE active fluorogen, and Pttc, a rigid three-dimensional moiety for anti-ACQ effect (top). Fluorescence intensities of the three CPs in mixed solvents of THF/water (water fraction, v/v%) (bottom).186 (c) Molecular structure of the PBPTV polymer. The inset shows bright-field and NIR-II fluorescence images of solid PBPTV (top). Fluorescence intensities of the CP in DCM/hexane mixtures with the change in the volume fractions of hexane (bottom).184 (a) Reproduced with permission from ref (187), copyright 2019 American Chemical Society. (b) Reproduced with permission from ref (186), copyright 2019 The Royal Society of Chemistry. (c) Reproduced with permission from ref (184), copyright 2020 American Chemical Society.
Figure 12 Improved fluorescence brightness of Pdots by antiaggregation-caused quenching and aggregation-induced emission. (a) Competition between the AIE and ACQ effects (top). The AIE polymer PBT demonstrated a remarkable increase in fluorescence intensity (QY increased from 9% in solution to 23% in Pdots). In contrast, the PTBT polymer displayed an intense ACQ effect, which resulted in low fluorescence emission after Pdot formation. Absorption and fluorescence spectra of the polymers PBT, PTBT, and PHTBT in THF (bottom left). Fluorescence intensity changes of PBT, PTBT, and PHTBT in THF/water mixtures with different water fractions (bottom right).187 (b) Chemical structures of three CPs with different donors; PF, dominated by the ACQ effect, TPE, AIE active fluorogen, and Pttc, a rigid three-dimensional moiety for anti-ACQ effect (top). Fluorescence intensities of the three CPs in mixed solvents of THF/water (water fraction, v/v%) (bottom).186 (c) Molecular structure of the PBPTV polymer. The inset shows bright-field and NIR-II fluorescence images of solid PBPTV (top). Fluorescence intensities of the CP in DCM/hexane mixtures with the change in the volume fractions of hexane (bottom).184 (a) Reproduced with permission from ref (187), copyright 2019 American Chemical Society. (b) Reproduced with permission from ref (186), copyright 2019 The Royal Society of Chemistry. (c) Reproduced with permission from ref (184), copyright 2020 American Chemical Society.CC BY · PubMed Central
Figure 13 Improved fluorescence brightness of Pdots by incorporating fluorescent dyes into conjugated polymers. (a) Chemical structure and schematic illustration of cascade energy transfer in multicolor narrow emissive Pdots based on BODIPY units (top). Diagram of bioconjugation for specific cellular targeting (bottom).191 (b) Chemical structures of CPs conjugated to a polymethine dye. Three types of SWIR fluorescent polymethine dyes (NIR1125, NIR1270, and NIR1380) were used for conjugation.195 (c) Structure of the conjugated polymer backbone incorporating a porphyrin unit emitting in NIR (top). Schematic illustration of the preparation of NIR800 Pdots for a bioimaging application (bottom).193 (a) Adopted with permission from ref (191), copyright 2013 American Chemical Society. (b) Reproduced with permission from ref (195), copyright 2020 Wiley-VCH Verlag GmbH & Co. (c) Reproduced with permission from ref (193), copyright 2017 The Royal Society of Chemistry.
Figure 13 Improved fluorescence brightness of Pdots by incorporating fluorescent dyes into conjugated polymers. (a) Chemical structure and schematic illustration of cascade energy transfer in multicolor narrow emissive Pdots based on BODIPY units (top). Diagram of bioconjugation for specific cellular targeting (bottom).191 (b) Chemical structures of CPs conjugated to a polymethine dye. Three types of SWIR fluorescent polymethine dyes (NIR1125, NIR1270, and NIR1380) were used for conjugation.195 (c) Structure of the conjugated polymer backbone incorporating a porphyrin unit emitting in NIR (top). Schematic illustration of the preparation of NIR800 Pdots for a bioimaging application (bottom).193 (a) Adopted with permission from ref (191), copyright 2013 American Chemical Society. (b) Reproduced with permission from ref (195), copyright 2020 Wiley-VCH Verlag GmbH & Co. (c) Reproduced with permission from ref (193), copyright 2017 The Royal Society of Chemistry.CC BY · PubMed Central
Figure 14 Single-particle SWIR imaging with Pdots (a) Steady-state absorption (solid lines) and fluorescence (dashed lines) spectra of PSN Pdots with three different sizes dispersed in water. (b) Schematic illustration describing the experimental configuration of single-particle fluorescence imaging of the PSN Pdots through tissue phantoms. (c) Fluorescence images of individual PSN Pdots deposited onto the tissue phantoms with varied thickness, as captured by the visible/NIR-I detector (left) and the SWIR detector (right).215 Reproduced with permission from ref (215), copyright 2020 American Chemical Society.
Figure 14 Single-particle SWIR imaging with Pdots (a) Steady-state absorption (solid lines) and fluorescence (dashed lines) spectra of PSN Pdots with three different sizes dispersed in water. (b) Schematic illustration describing the experimental configuration of single-particle fluorescence imaging of the PSN Pdots through tissue phantoms. (c) Fluorescence images of individual PSN Pdots deposited onto the tissue phantoms with varied thickness, as captured by the visible/NIR-I detector (left) and the SWIR detector (right).215 Reproduced with permission from ref (215), copyright 2020 American Chemical Society.CC BY · PubMed Central
Figure 15 Fluorescence intensity saturation in single-particle SWIR fluorescence imaging. Excitation power dependence of the fluorescence intensity obtained for individual (a) PbS QDs (QDs), (b) 3.6 nm BBT Pdots (B3.6), (c) IR-E1050 dye-doped NPs (IRNPs), (d) 3.5 nm PSN Pdots (P3.5), (e) 14.3 nm PSN Pdots (P14.3), and (f) 31.9 nm PSN Pdots (P31.9) deposited onto a glass coverslip. The solid lines show fitting of the data to a two-state model. (g) Saturation intensities and (h) maximum fluorescence count rates obtained for the SWIR-emitting fluorophores determined by fitting the excitation power-dependent fluorescence intensity displayed in (a–f).215 Reproduced with permission from ref (215), copyright 2020 American Chemical Society.
Figure 15 Fluorescence intensity saturation in single-particle SWIR fluorescence imaging. Excitation power dependence of the fluorescence intensity obtained for individual (a) PbS QDs (QDs), (b) 3.6 nm BBT Pdots (B3.6), (c) IR-E1050 dye-doped NPs (IRNPs), (d) 3.5 nm PSN Pdots (P3.5), (e) 14.3 nm PSN Pdots (P14.3), and (f) 31.9 nm PSN Pdots (P31.9) deposited onto a glass coverslip. The solid lines show fitting of the data to a two-state model. (g) Saturation intensities and (h) maximum fluorescence count rates obtained for the SWIR-emitting fluorophores determined by fitting the excitation power-dependent fluorescence intensity displayed in (a–f).215 Reproduced with permission from ref (215), copyright 2020 American Chemical Society.CC BY · PubMed Central
Figure 16 Single-particle time-gated SWIR fluorescence imaging. (a) Schematic illustration describing the basic principle of time-gated detection. (b, c) Fluorescence decay curves of the (b) NPs doped with IR-E1050 dye and (c) PSN Pdots (red) with the instrument response function (green). The gray-shaded regions correspond to the applied time delay of the detection. The blue arrows show the applied time gate of the detection. Fluorescence images of individual (d) PSN Pdots deposited onto a 40-μm-thick tissue phantom captured at varied time gates with signal-to-background ratios at applied time gate depicted.215 Reproduced with permission from ref (215), copyright 2020 American Chemical Society.
Figure 16 Single-particle time-gated SWIR fluorescence imaging. (a) Schematic illustration describing the basic principle of time-gated detection. (b, c) Fluorescence decay curves of the (b) NPs doped with IR-E1050 dye and (c) PSN Pdots (red) with the instrument response function (green). The gray-shaded regions correspond to the applied time delay of the detection. The blue arrows show the applied time gate of the detection. Fluorescence images of individual (d) PSN Pdots deposited onto a 40-μm-thick tissue phantom captured at varied time gates with signal-to-background ratios at applied time gate depicted.215 Reproduced with permission from ref (215), copyright 2020 American Chemical Society.CC BY · PubMed Central
Figure 17 Fluorescence brightness of NIR/SWIR emitting organic fluorophores. Experimentally observed (a) Φfl and (b) fluorescence brightness (ε × Φfl) as a function of the peak fluorescence wavelength of different classes of NIR/SWIR emitting organic fluorophores.
Figure 17 Fluorescence brightness of NIR/SWIR emitting organic fluorophores. Experimentally observed (a) Φfl and (b) fluorescence brightness (ε × Φfl) as a function of the peak fluorescence wavelength of different classes of NIR/SWIR emitting organic fluorophores.CC BY · PubMed Central

Verification

Claims the paper makes

82 Valid · 7 Not valid · 126 Not checked · 63 Own results and interpretations

170 more claims · 50 with their cited sources checked

Create a free account to see all 278 claims and to verify the 4 references still open.

See all claims — free account
  • Probably not a substantial claim. 39
  • It may state two separate claims as one. 72
  • The quote only partly states this claim. 1

Create a free account to see these claims.

Citations

Cites

Show all 230 references

Research works printed but not linked: 2

  1. Habuchi S.; Fujita H.; Michinobu T.; Vacha M. Twist Angle Plays an Important Role in Photophysical Properties of a Donor–Acceptor-Type Conjugated Polymer: A Combined Ensemble and Single-Molecule Study. J. Phys. Chem. B 2011, 115 (49), 14404– 14415. 10.1021/jp209405k. 22044438 · DOI · Paper page
  2. Liu M.-H.; Zhang Z.; Yang Y.-C.; Chan Y.-H. Polymethine-Based Semiconducting Polymer Dots with Narrow-Band Emission and Absorption/Emission Maxima at NIR-II for Bioimaging. Angew. Chem., Int. Ed. 2021, 60 (2), 983– 989. 10.1002/anie.202011914. 32990356 · DOI · Paper page

Cited by

See all 39

Metadata

Authors
Piwoński, H., Nozue, S., & Habuchi, S.
Affiliations
King Abdullah University of Science and Technology (SA)
Corresponding author
  • Piwoński, Hubert
  • Habuchi, Satoshi
Venue
ACS Nanoscience Au
Published
2022-02-21
Volume
2
Issue
4
Pages
253-283
ISSN
2694-2496 (ISSN-L)
OpenAlex
W4213045763
Cited by
39
References
230
Citations by year
2026: 7 · 2025: 13 · 2024: 9 · 2023: 9 · 2022: 1
FWCI
0.52
Type
journal article
Language
en
Open access
Locations
  • ACS Nanoscience Au (publishedVersion, cc-by)
  • PubMed Central (publishedVersion, cc-by)
  • PubMed (publishedVersion)
  • King Abdullah University of Science and Technology Repository (King Abdullah University of Science and Technology) (submittedVersion, cc-by)
Funders
King Abdullah University of Science and Technology (OSR-CRG2020-4390)
Topics
  • Physical Sciences › Materials Science › Materials Chemistry › Luminescence and Fluorescent Materials
  • Physical Sciences › Chemistry › Spectroscopy › Molecular Sensors and Ion Detection
  • Physical Sciences › Chemistry › Physical and Theoretical Chemistry › Photochemistry and Electron Transfer Studies
Keywords
organic nanoparticles, molecular aggregates, fluorescence intensity, molecular design, conjugated polymers, polymeric nanoparticles, chain conformation, deep tissue imaging, single-particle imaging, fluorescence quantum yield

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

The claim verdicts this report counts are experimental: their accuracy is not yet measured.

A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).

A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).

Cited sources are checked with a language model’s help (gpt-6-sol).

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.