The DOI matches its Crossref record; 43 of the 43 references it cites were found in a registry or an index.
Research on the printability of hydrogels in 3D bioprinting
Open accessAbstract
As the biocompatible materials, hydrogels have been widely used in three- dimensional (3D) bioprinting/organ printing to load cell for tissue engineering. It is important to precisely control hydrogels deposition during printing the mimic organ structures. However, the printability of hydrogels about printing parameters is seldom addressed. In this paper, we systemically investigated the printability of hydrogels from printing lines (one dimensional, 1D structures) to printing lattices/films (two dimensional, 2D structures) and printing 3D structures with a special attention to the accurate printing. After a series of experiments, we discovered the relationships between the important factors such as air pressure, feedrate, or even printing distance and the printing quality of the expected structures. Dumbbell shape was observed in the lattice structures printing due to the hydrogel diffuses at the intersection. Collapses and fusion of adjacent layer would result in the error accumulation at Z direction which was an important fact that could cause printing failure. Finally, we successfully demonstrated a 3D printing hydrogel scaffold through harmonize with all the parameters. The cell viability after printing was compared with the casting and the results showed that our bioprinting method almost had no extra damage to the cells.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
3D bioprinting of tissues and organs
Murphy, S. V., & Atala, A. (2014) · Nature Biotechnology · doi:10.1038/nbt.2958 · Cited by 7,034
25th Anniversary Article: Engineering Hydrogels for Biofabrication
Malda, J., Visser, J., Melchels, F. P., Jüngst, T., Hennink, W. E., Dhert, W. J. A., Groll, J., & Hutmacher, D. W. (2013) · Advanced Materials · doi:10.1002/adma.201302042 · Cited by 1,901
Bone tissue engineering using 3D printing
Bose, S., Vahabzadeh, S., & Bandyopadhyay, A. (2013) · Materials Today · doi:10.1016/j.mattod.2013.11.017 · Cited by 1,866
Current advances and future perspectives in extrusion-based bioprinting
Ozbolat, I. T., & Hospodiuk, M. (2016) · Biomaterials · doi:10.1016/j.biomaterials.2015.10.076 · Cited by 1,572
Scaffold-free vascular tissue engineering using bioprinting
Norotte, C., Marga, F. S., Niklason, L. E., & Forgacs, G. (2009) · Biomaterials · doi:10.1016/j.biomaterials.2009.06.034 · Cited by 1,339
Organ printing: Tissue spheroids as building blocks
Mironov, V., Visconti, R. P., Kasyanov, V., Forgacs, G., Drake, C. J., & Markwald, R. R. (2009) · Biomaterials · doi:10.1016/j.biomaterials.2008.12.084 · Cited by 1,238
Printing and Prototyping of Tissues and Scaffolds
Derby, B. (2012) · Science · doi:10.1126/science.1226340 · Cited by 1,108
Fabricated: The New World of 3D Printing
Lipson, H., & Kurman, M. (2013) · Cited by 1,032
3D Bioprinting of heterogeneous aortic valve conduits with alginate/gelatin hydrogels
Duan, B., Hockaday, L. A., Kang, K. H., & Butcher, J. T. (2013) · Journal of Biomedical Materials Research Part A · doi:10.1002/jbm.a.34420 · Cited by 1,002
Mannoor, M. S., Jiang, Z., James, T., Kong, Y. L., Malatesta, K. A., Soboyejo, W. O., Verma, N., Gracias, D. H., & McAlpine, M. C. (2013) · Nano Letters · doi:10.1021/nl4007744 · Cited by 874
Cited by
3D bioprinting for biomedical devices and tissue engineering: A review of recent trends and advances
Derakhshanfar, S., Mbeleck, R., Xu, K., Zhang, X., Zhong, W., & Xing, M. (2018) · Bioactive Materials · doi:10.1016/j.bioactmat.2017.11.008 · Cited by 1,027
3D printing of hydrogels: Rational design strategies and emerging biomedical applications
Li, J., Wu, C., Chu, P. K., & Gelinsky, M. (2020) · Materials Science and Engineering: R: Reports · doi:10.1016/j.mser.2020.100543 · Cited by 862
Review of alginate-based hydrogel bioprinting for application in tissue engineering
Rastogi, P., & Kandasubramanian, B. (2019) · Biofabrication · doi:10.1088/1758-5090/ab331e · Cited by 564
Engineering and Functionalization of Gelatin Biomaterials: From Cell Culture to Medical Applications
Bello, A. B., Kim, D., Kim, D., Park, H., & Lee, S.-H. (2020) · Tissue Engineering Part B: Reviews · doi:10.1089/ten.teb.2019.0256 · Cited by 545
Liu, Z., Bhandari, B., Prakash, S., Mantihal, S., & Zhang, M. (2019) · Food Hydrocolloids · doi:10.1016/j.foodhyd.2018.08.026 · Cited by 530
‘Printability' of Candidate Biomaterials for Extrusion Based 3D Printing: State‐of‐the‐Art
Kyle, S., Jessop, Z. M., Al‐Sabah, A., & Whitaker, I. S. (2017) · Advanced Healthcare Materials · doi:10.1002/adhm.201700264 · Cited by 495
An Introduction to 3D Bioprinting: Possibilities, Challenges and Future Aspects
Kačarević, Ž. P., Rider, P. M., Alkildani, S., Retnasingh, S., Smeets, R., Jung, O., Ivanišević, Z., & Barbeck, M. (2018) · Materials · doi:10.3390/ma11112199 · Cited by 479
Assessing bioink shape fidelity to aid material development in 3D bioprinting
Ribeiro, A., Blokzijl, M. M., Levato, R., Visser, C. W., Castilho, M., Hennink, W. E., Vermonden, T., & Malda, J. (2017) · Biofabrication · doi:10.1088/1758-5090/aa90e2 · Cited by 448
3D Bioprinting: from Benches to Translational Applications
Heinrich, M. A., Liu, W., Jimenez, A., Yang, J., Akpek, A., Liu, X., Pi, Q., Mu, X., Hu, N., Schiffelers, R. M., et al. (2019) · Small · doi:10.1002/smll.201805510 · Cited by 437
Assessment methodologies for extrusion-based bioink printability
Gillispie, G., Prim, P., Copus, J., Fisher, J., Mikos, A. G., Yoo, J. J., Atala, A., & Lee, S. J. (2020) · Biofabrication · doi:10.1088/1758-5090/ab6f0d · Cited by 426
Crosslinking Strategies for 3D Bioprinting of Polymeric Hydrogels
GhavamiNejad, A., Ashammakhi, N., Wu, X. Y., & Khademhosseini, A. (2020) · Small · doi:10.1002/smll.202002931 · Cited by 400
Aqueous Two‐Phase Emulsion Bioink‐Enabled 3D Bioprinting of Porous Hydrogels
Ying, G., Jiang, N., Maharjan, S., Yin, Y., Chai, R., Cao, X., Yang, J., Miri, A. K., Hassan, S., & Zhang, Y. S. (2018) · Advanced Materials · doi:10.1002/adma.201805460 · Cited by 377
Shear-Thinning and Thermo-Reversible Nanoengineered Inks for 3D Bioprinting
Wilson, S. A., Cross, L. M., Peak, C. W., & Gaharwar, A. K. (2017) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.7b13602 · Cited by 369
3D Printability of Alginate-Carboxymethyl Cellulose Hydrogel
Habib, A., Sathish, V., Mallik, S., & Khoda, B. (2018) · Materials · doi:10.3390/ma11030454 · Cited by 330
3D printing with cellulose materials
Wang, Q., Sun, J., Yao, Q., Ji, C., Liu, J., & Zhu, Q. (2018) · Cellulose · doi:10.1007/s10570-018-1888-y · Cited by 324
Soy Protein: Molecular Structure Revisited and Recent Advances in Processing Technologies
Sui, X., Zhang, T., & Jiang, L. (2021) · Annual Review of Food Science and Technology · doi:10.1146/annurev-food-062220-104405 · Cited by 318
Current Biomedical Applications of 3D Printing and Additive Manufacturing
Ahangar, P., Cooke, M. E., Weber, M. H., & Rosenzweig, D. H. (2019) · Applied Sciences · doi:10.3390/app9081713 · Cited by 309
Digitally Tunable Microfluidic Bioprinting of Multilayered Cannular Tissues
Pi, Q., Maharjan, S., Yan, X., Liu, X., Singh, B., van Genderen, A. M., Robledo‐Padilla, F., Parra‐Saldivar, R., Hu, N., Jia, W., et al. (2018) · Advanced Materials · doi:10.1002/adma.201706913 · Cited by 305
Structured Macroporous Hydrogels: Progress, Challenges, and Opportunities
De France, K. J., Xu, F., & Hoare, T. (2018) · Advanced Healthcare Materials · doi:10.1002/adhm.201700927 · Cited by 279
Printability–A key issue in extrusion-based bioprinting
Naghieh, S., & Chen, X. (2021) · Journal of Pharmaceutical Analysis · doi:10.1016/j.jpha.2021.02.001 · Cited by 270
Polymeric Systems for Bioprinting
Bedell, M. L., Navara, A. M., Du, Y., Zhang, S., & Mikos, A. G. (2020) · Chemical Reviews · doi:10.1021/acs.chemrev.9b00834 · Cited by 258
Physical and Chemical Factors Influencing the Printability of Hydrogel-based Extrusion Bioinks
Lee, S. C., Gillispie, G., Prim, P., & Lee, S. J. (2020) · Chemical Reviews · doi:10.1021/acs.chemrev.0c00015 · Cited by 255
Bom, S., Ribeiro, R., Ribeiro, H. M., Santos, C., & Marto, J. (2022) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2022.121506 · Cited by 230
3D bioprinting of structural proteins
Włodarczyk-Biegun, M. K., & del Campo, A. (2017) · Biomaterials · doi:10.1016/j.biomaterials.2017.04.019 · Cited by 185
Polysaccharide matrices used in 3D in vitro cell culture systems
Diekjürgen, D., & Grainger, D. W. (2017) · Biomaterials · doi:10.1016/j.biomaterials.2017.06.020 · Cited by 125
Stepanovska, J., Supova, M., Hanzalek, K., Broz, A., & Matejka, R. (2021) · Biomedicines · doi:10.3390/biomedicines9091137 · Cited by 112
Vancauwenberghe, V., Verboven, P., Lammertyn, J., & Nicolaï, B. (2018) · Journal of Food Engineering · doi:10.1016/j.jfoodeng.2018.01.008 · Cited by 96
4D printing of polyurethane paint-based composites
Su, J.-W., Gao, W., Trinh, K., Kenderes, S. M., Tekin Pulatsu, E., Zhang, C., Whittington, A., Lin, M., & Lin, J. (2019) · International Journal of Smart and Nano Materials · doi:10.1080/19475411.2019.1618409 · Cited by 81
Constructing biomimetic liver models through biomaterials and vasculature engineering
Lv, W., Zhou, H., Aazmi, A., Yu, M., Xu, X., Yang, H., Huang, Y. Y. S., & Ma, L. (2022) · Regenerative Biomaterials · doi:10.1093/rb/rbac079 · Cited by 45
Modeling a dynamic printability window on polysaccharide blend inks for extrusion bioprinting
Perin, F., Spessot, E., Famà, A., Bucciarelli, A., Callone, E., Mota, C., Motta, A., & Maniglio, D. (2023) · ACS Biomaterials Science & Engineering · doi:10.1021/acsbiomaterials.2c01143 · Cited by 33
Metadata
- Authors
- He, Y., Yang, F., Zhao, H., Gao, Q., Xia, B., & Fu, J.
- Venue
- Scientific Reports
- Published
- 2016-07-20
- Volume
- 6
- Issue
- 1
- Pages
- 29977-29977
- ISSN
- 2045-2322 (ISSN-L)
- OpenAlex
- W2488863215
- Cited by
- 654
- References
- 43
- FWCI
- 27.97
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.