A Review of Bidirectional On-Board Chargers for Electric Vehicles
Open accessThe DOI matches its Crossref record; 155 of the 159 references it cites were found in a registry or an index; 19 of the 150 sources its claims cite were checked for support.
Abstract
The fast development of electric vehicles (EVs) provides significant opportunities to further utilize clean energies in the automotive. On-board chargers (OBCs) are widely used in EVs because of their simple installation and low cost. Limited space in the vehicle and short charging time require an OBC to be power-dense and highly efficient. Moreover, the possibility for EVs to deliver power back to the grid has increased the interest in bidirectional power flow solutions in the automotive market. This paper presents a comprehensive overview and investigation on the state-of-the-art solutions of bidirectional OBCs. It reviews the current status, including architectures and configurations, smart operation modes, industry standards, major components, and commercially available products. A detailed overview of the promising topologies for bidirectional OBCs, including two-stage and single-stage structures, is provided. Future trends and challenges for topologies, wide bandgap technologies, thermal management, system integration, and wireless charging systems are also discussed in this paper.
Overview
CoChat Summary
TL;DR
This review surveys bidirectional on-board chargers (OBCs) for electric vehicles, covering architectures, operation modes, standards, components, commercial products, and promising two-stage and single-stage topologies. It finds two-stage designs dominate commercial use, while single-stage high-power bidirectional OBCs remain mostly theoretical despite higher power-density potential.
Key findings
- Bidirectional OBCs enable V2G, V2H, V2L, and V2V; current use is mainly level-2 AC charging from 3.7 kW to 22 kW, while level-3 AC reverse power flow is mostly limited to 6.6–12 kW due to battery degradation and capacity.
- Commercial examples include Texas Instruments’ 6.6 kW SiC OBC at 97% efficiency, Delta-q’s 6.6 kW unit above 96% efficiency and 2.26 kW/L, Wolfspeed’s 6.6 kW unit at 3.3 kW/L and >96.5% peak efficiency, and Current Ways’ 20 kW modular SiC OBC above 97% efficiency and 3.3 kW/L.
- Most commercial bidirectional OBCs use a two-stage structure with a totem-pole PFC front end and CLLC or DAB DC/DC stage; PFC converters commonly exceed 98% efficiency, and DC/DC converters generally exceed 98%, but high power density at high power ratings remains challenging.
- Single-stage OBCs remove the bulky DC-link capacitor and can offer higher power density and lower cost, but most are theoretical, suffer low efficiency and complex control, and no high-power commercial product has been developed to date.
Methods
- Review paper: qualitative synthesis of state-of-the-art bidirectional OBCs, including architectures, configurations, smart operation modes, industry standards, major components, and commercially available products.
- Data sources: published literature, standards documents, and posted information from six commercial examples—Texas Instruments, Delta-q, Wolfspeed, Current Ways, Valeo Siemens, and Eaton—plus discussion of BYD, Tesla, Renault, BMW, Honda, and Nissan examples.
- Main analysis: comparative review of two-stage and single-stage topologies, PFC and DC/DC converter options, wide-bandgap devices, thermal management, system integration, and wireless charging trends, supported by summary tables.
Limitations
- Paper-stated: bidirectional OBCs face additional system cost, reliability burden, low power density, high weight, and complex smart-grid architecture implementation; V2G is still early-stage and not yet applied in the industry due to battery capacity and grid infrastructure limits.
- Paper-stated: frequent charging/discharging causes battery degradation—daily 2-hour frequency regulation is reported to consume 14.3% of battery capacity, and adding peak shaving can take up to 35.6%.
- Evident from text: as a review, it does not describe a systematic literature-search or selection method, and performance comparisons rely on manufacturer-posted or literature data with missing fields, such as power density not being shared by most manufacturers; no independent experimental validation is reported.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
15 Valid · 33 Not valid · 85 Not checked · 107 Own results and interpretations
Every source the paper cites for this claim was checked and supports it.
In the paper
“The high switching frequency of high power-dense bidirectional OBCs results in potential thermal management challenges because of higher switching loss and eddy current loss [72].”
What the sources say
- Supportedcites [72] [72] K. Gupta, C. Da Silva, M. Nasr, A. Assadi, H. Matsumoto, O. Trescases, and C. H. Amon, ''Thermal management strategies for a high-frequency, bi-directional, on-board electric vehicle charger,'' in Proc. 17th IEEE Intersociety Conf. Thermal Thermomechanical Phenomena Electron. Syst. (ITherm) , San Diego, CA, USA, May 2018, pp. 935 943. - source
The Introduction states that higher switching frequency causes thermal-management challenges through higher MOSFET switching losses and considerably higher eddy-current losses in heat sinks. This directly supports the cited sentence. (LLM, conf=0.95)
hedgedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
Every source the paper cites for this claim was checked and supports it.
In the paper
“Moreover, the V2G mode can help to reduce the grid current harmonics. The battery chargers are treated as variable impedance and eliminate the harmonics issue through appropriate ltering methods [45].”
What the sources say
- Supportedcites [45] [45] Z. A. Arfeen, A. B. Khairuddin, A. Munir, M. K. Azam, M. Faisal, and M. S. B. Arif, ''En route of electric vehicles with the vehicle to grid technique in distribution networks: Status and technological review,'' Energy Storage , vol. 2, no. 2, p. e115, Apr. 2020. - source
Section 5 (VEHICLE TO GRID) lists among V2G's advantages the explicit item 'reduce current harmonics' and states 'The inclusion of V2G can give better harmonics filtration'. Section 5.4 (Harmonic filtering) supplies the second half of the sentence: EV/power chargers 'act as a variable impedance for discrete frequencies and resolves the harmonic issues with an appropriate filtering method.' Both parts of the paraphrase are stated in our copy. (LLM, conf=0.90)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Most manufacturers study the totem-pole PFC topology as the front-end stage and DAB or CLLC topologies as the back-end stage.”
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“To this day, there are only a few bidirectional single-stage OBCs used in the automobile industry.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“However, no commercial product has been developed to this day.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
39 more claims
Create a free account to see all 240 claims and to verify the 7 references still open.
- It may state two separate claims as one. 112
- Probably not a substantial claim. 130
- The quote only partly states this claim. 2
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The cited source doesn’t support the claim as written.
In the citing paper
“The study in [52] includes very few selected bidirectional OBCs, consisting of a report on the power density of four industrial OBCs.”
From On-Board Chargers for Electric Vehicles: A Comprehensive Performance and Efficiency Review (2024) · cites this paper as [52]
Checked by a reasoning model — may be wrong.
Experimental — accuracy not yet measured
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ TABLE 4. Bidirectional PFC summary. · p. 8
“the converter achieves up to 98.86% ef ciency at a 1.6kW power level [78].”
§ TABLE 4. Bidirectional PFC summary. · p. 8
“| | Three-phase | CRM | 85-265 | 390 | 450-1000 | 1.6 | 98.7 | >15 | GaN | >0.99 |”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ C. STANDARDS · p. 4
“the total harmonic distortion (THD) of currents should be less than 7% to comply with the Institute of Electrical and Electronics Engineers (IEEE) 519 requirements [54].”
§ 1) EMI FILTERS · p. 5
“Recommended practice and requirements for stable harmonics limitation of the voltage and current (THD<8%)”
Citations
Cites
Yilmaz, M., & Krein, P. T. (2013) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2012.2212917 · Cited by 3,118
A Review of Three-Phase Improved Power Quality AC–DC Converters
Singh, B., Singh, B. N., Chandra, A., Al-Haddad, K., Pandey, A., & Kothari, D. P. (2004) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2004.825341 · Cited by 1,728 · cited 1×
“In addition to single-phase PFC topologies, a lot of research is being undertaken on three-phase bidirectional PFC converters like the full-bridge converter [95], NPC [93], T-type [96] and matrix converter [97]–[99].”
BackgroundA review of single-phase improved power quality ac~dc converters
Singh, B., Singh, B. N., Chandra, A., Al-Haddad, K., Pandey, A., & Kothari, D. P. (2003) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2003.817609 · Cited by 1,297 · cited 1×
“For example, single-phase bidirectional full-bridge converters, and their variants are popular but suffer high power losses [85]–[87].”
BackgroundModern Trends in Inductive Power Transfer for Transportation Applications
Covic, G. A., & Boys, J. T. (2013) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2013.2264473 · Cited by 1,263 · cited 1×
“Many methods are proposed like road built-in pad [160], pad array-based coupling technique [161], and segmental track strategy [162].”
MethodReview of Commercial GaN Power Devices and GaN-Based Converter Design Challenges
Jones, E. A., Wang, F. F., & Costinett, D. (2016) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2016.2582685 · Cited by 1,259 · cited 1×
“GaN semiconductors reaches up to 650V, these devices are becoming an attractive solution for OBCs [142].”
BackgroundUsing fleets of electric-drive vehicles for grid support
Tomić, J., & Kempton, W. (2007) · Journal of Power Sources · doi:10.1016/j.jpowsour.2007.03.010 · Cited by 1,018 · cited 1×
“A variable DC-link voltage of the PFC converter can mitigate this disadvantage, but the resonant tank needs to be carefully designed to cover that wide-voltage range [125], [126].”
BackgroundSchweizer, M., & Kolar, J. W. (2013) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2012.2203151 · Cited by 1,006 · cited 14×
“[96] M. Schweizer and J. W. Kolar, ‘‘Design and implementation of a highly efficient three-level T-type converter for low-voltage applications,’’ IEEE Trans.”
BackgroundMethodInfluentialPerformance Evaluation of Bridgeless PFC Boost Rectifiers
Huber, L., Jang, Y., & Jovanovic, M. M. (2008) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2008.921107 · Cited by 865
Un-Noor, F., Padmanaban, S., Mihet-Popa, L., Mollah, M., & Hossain, E. (2017) · Energies · doi:10.3390/en10081217 · Cited by 809 · cited 1×
“However, they do not concentrate on the research and application of the bidirectional OBC [1], [13], [25], [26].”
BackgroundThe Essence of Three-Phase PFC Rectifier Systems—Part I
Kolar, J. W., & Friedli, T. (2013) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2012.2197867 · Cited by 788
Research works printed but not linked: 21
- [39] X. Gong and J. Rangaraju, ''Taking charge of electric vehicles Both in the vehicle and on the grid,'' Texas Instrum., Dallas, TX, USA, Tech. Rep. SZZY007A, Jun. 2020, pp. 1 13. -
- [35] G. Yang, E. Draugedalen, T. Sorsdahl, H. Liu, and R. Lindseth, ''Design of high ef ciency high power density 10.5 kw three phase on-boardcharger for electric/hybrid vehicles,'' in Proc. Int. Exhib. Conf. Power Electron., Intell. Motion, Renew. Energy Manage. , Nuremberg, Germany, May 2016, pp. 1 7. -
- [23] Electrical and Electronics Technical Team Roadmap , UDD, Mumbai, India, Oct. 2017. -
- [58] IEEE Standard for Interconnection and Interoperability of Distributed Energy Resources With Associated Electric Power Systems Interfaces , Standard 1547-2018, Apr. 2018. -
- [57] Auto-Delivery , document GB/T 14549-1993, Mar. 1994. -
- [56] bar IEC Webstore , document IEC 61851-1:2017, Feb. 2017. -
- [55] Power Quality Requirements for Plug-In Electric Vehicle Chargers SAE International , Standard J2894/1B (WIP), Jun. 2020. -
- [54] IEEE Recommended Practice and Requirements for Harmonic Control in Electric Power Systems , Standard 519-2014, Mar. 2014. -
- [73] A. Goswami, ''Thermal management of on-board chargers in E-vehicles,'' Electron. Cooling , Aug. 2017. -
- [71] On Board Charger (OBC) LLC Converter , document TND6318/D, Sep. 2019. -
- [70] D. Giacomini, ''An overview and comparison of on board chargers topologies, semiconductors choices and synchronous recti cation advantages in automotive applications,'' In neon Italy s.r.l. ATV Group, Padua, Italy, Tech. Rep., May 2017, pp. 1 23. -
- [78] TIDM-1007 High Ef ciency GaN CCM Totem Pole Bridgeless Power Factor Correction (PFC) Reference Design , Taxes Instruments, Bengaluru, India, Mar. 2020. -
- [61] Electrically Propelled Vehicles , document ISO 6469-1:2019, Apr. 2019. -
- [63] S.-O. Plugs, ''Vehicle connectors and vehicle inlets conductive charging of electric vehicles Part 1, 2, 3,'' IEC Standard , vol. 62196, pp. 1 176, Jun. 2014. -
- [64] P. Contact, ''Charging technology for E-mobility Product overview 2017,'' Inspiring Innov. , vol. 2, pp. 1 56, Dec. 2014. <!-- image --> IEEEAccess" -
- [68] B. Johnson, ''Power factor correction design for on-board chargers in electric vehicles,'' Texas Instrum., Dallas, TX, USA, Tech. Rep. SLUA896, Jun. 2018, pp. 1 17. -
- 2019, Infineon
- [103] On Board Charger (OBC) Three-Phase PFC Converter , ON Semiconductor, Phoenix, AZ, USA, Mar. 2020. -
- [81] 6.6 kw High Power Density Bi-Directional EV on-Board Charger , Cree Power Applications, Durham, CA, USA, Jan. 2020. -
- 2013, On-Board Charger Specifications Eaton
- [119] TIDA-010054 Bi-Directional, Dual Active Bridge Reference Design for Level 3 Electric Vehicle Charging Stations , Texas Instrum., Dallas, TX, USA, Jun. 2019. -
Cited by
Items 101–200 of 379
Lee, J., Le, T.-T., Kim, H., & Choi, S. (2025) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2024.3525104 · Cited by 11
Xiong, F. B., Wu, P., Yang, H., Zhang, K., & Yan, D. (2023) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2023.3306869 · Cited by 10
Emamalipour, R., & Lam, J. C. W. (2022) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2022.3151561 · Cited by 9
“Table I provides a summary of the high-frequency high voltage conversion ratio dc–dc converters discussed in the literature [17]–[19].”
BackgroundIsolated AC/DC converter used in EV/PHEV battery charger from household AC outlet
Endo, D., Matsumori, H., Kosaka, T., et al. (2022) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce50734.2022.9948094 · Cited by 9
“A typical battery charger is consisted of a PFC converter for power factor correction and an isolated DC/DC converter for output voltage control [5], as shown in Fig.”
MethodReali, A., Alemanno, A., Ronchi, F., Rossi, C., & Florian, C. (2024) · Micromachines · doi:10.3390/mi15121470 · Cited by 11
“High efficiency and high power density requirements imposed by automotive players are leading power electronics designers to the implementation of an increasingly high switching frequency [27].”
de Oliveira, R. N. M., de Araújo, J. W. M., Barreto, L. H. S. C., Honório, D. D. A., & Oliveira, D. S. (2025) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2025.3544514 · Cited by 9
“Themost established solutions for conventional level 2 and level 3 charger topologies have two stages: an ac–dc converter ;andthedc–dcstage withgalvanicisolationathighfrequencyandcontrolledpower flowtothebatterypack[5],[6].”
Kougioulis, I., Vannini, A., Pal, A., Wheeler, P. W., & Ahmed, M. R. (2023) · European Conference on Power Electronics and Applications · doi:10.23919/epe23ecceeurope58414.2023.10264329 · Cited by 8
“and as a result, high-frequency (HF) power transformers are an inseparable part of the EV on-board charger [4].”
BackgroundDual Active Half Bridge Converter with Integrated Active Power Decoupling for On-Board EV Charger
Laturkar, A., Deshmukh, N., & Anand, S. (2022) · IEEE International Conference on Power Electronics, Smart Grid, and Renewable Energy (PESGRE) · doi:10.1109/pesgre52268.2022.9715900 · Cited by 8
Buberger, J., Hohenegger, M., Estaller, J., Wiedenmann, A., Grupp, W., Bliemetsrieder, W., Kuder, M., Lesnicar, A., & Weyh, T. (2023) · Electricity · doi:10.3390/electricity4020011 · Cited by 10
Asymmetric Resonant Tank Design for a Bidirectional CLLC Resonant Converter in G2V and V2G Operation
Ditze, S., Ehrlich, S., Happel, D., & Roßkopf, A. (2023) · Conference proceedings/Conference proceedings - IEEE Applied Power Electronics Conference and Exposition · doi:10.1109/apec43580.2023.10131351 · Cited by 10
“These need to be highly efficient in the mandatory charging mode (G2V), but at the same time offer the possibility to feed energy from the vehicle battery back into the mains (V2G) or to supply the vehicle owner's home with energy (V2H) [4][5].”
BackgroundKozielski, K., Mudiyanselage, G. A., Narimani, M., & Emadi, A. (2025) · IEEE Open Journal of Power Electronics · doi:10.1109/ojpel.2025.3587080 · Cited by 12
“In EVs this is often facilitated through a liquid cooled cold plate [132].”
Self-citationPanhwar, I. H., Mekhilef, S., Seyedmahmoudian, M., et al. (2025) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2025.3602832 · Cited by 7
“Efficient bidirectional EV charging systems are essential to support both grid-to-vehicle (G2V) and vehicle-to-grid (V2G) modes of operation [2], [3].”
Tiwari, H., Ghosh, A., Banerjee, S., Mazumdar, D., Sain, C., Ahmad, F., & Ustun, T. S. (2024) · Frontiers in Energy Research · doi:10.3389/fenrg.2024.1440258 · Cited by 8
A Dual Active Bridge-Based Converter for Electric Vehicle Integration in Hybrid Microgrids
Sora, J., & Serban, I. (2024) · International Conference and Exposition on Electrical and Power Engineering (EPE) · doi:10.1109/epei63510.2024.10758098 · Cited by 8
“A review of the isolated DC-DC converter topologies is presented in [6] and the paper highlights that the dual active bridge (DAB) converter is the most commonly used topology for EV charging systems.”
Deepti, T., Deepa, K., Stonier, A. A., Peter, G., Anoop, A., Shahila, D. F. D., Ganji, V., & Jha, A. (2025) · IET Circuits Devices & Systems · doi:10.1049/cds2/3536991 · Cited by 10
“To enhance system ef fi ciency, diode bridges are employed at both the input stage and the secondary side postisolation [30].”
Multi-Objective Optimization of Bi-directional On-Board Chargers Based on 650V GaN Power Transistors
Bay, O., Hosseinabadi, F., Chakraborty, S., Baghdadi, M. E., & Hegazy, O. (2022) · Annual Conference of the IEEE Industrial Electronics Society (IECON) · doi:10.1109/iecon49645.2022.9968522 · Cited by 10
“However, the performance of Si-based OBCs is limited due to their material characteristics and further development of Sibased semiconductors is not possible.”
BackgroundInfluentialKomeda, S., Takuma, S., & Ohnuma, Y. (2023) · IEEJ Journal of Industry Applications · doi:10.1541/ieejjia.22007817 · Cited by 7
Single-Stage Bidirectional PFC Based Plug-in G2V EV Charger
Patel, N., Lopes, L. A. C., & Rathore, A. K. (2022) · IEEE International Conference on Power Electronics, Drives and Energy Systems · doi:10.1109/pedes56012.2022.10080548 · Cited by 10
“1(b), the single-phase V2G enabled plug-in EV charger configurations is discussed at various geographical area including North America, Europe and AsiaPacific regions [5].”
BackgroundKanthi Mathew, K., & Abraham, D. M. (2023) · Electric Power Components and Systems · doi:10.1080/15325008.2023.2199736 · Cited by 7
High‐Performance Single‐Phase Bi‐Directional Novel On‐Board Charger for Electric Vehicles
Ali, M. I., Mandal, R., & Kumar, A. (2024) · Energy Storage · doi:10.1002/est2.70014 · Cited by 6
“These manufacturers include Texas Instruments, delta-q, Wolf Speed, Current Ways, Valeo Siemens and Eaton, and so forth [6].”
Gupta, J., & Singh, B. (2025) · IEEE Transactions on Consumer Electronics · doi:10.1109/tce.2025.3550197 · Cited by 7
“Besides AC-DC stage as back-end stage of conventional two stage unidirectional/bidirectional chargers, is usually implemented based on transformer-based DC-DC converters [4], [5], [14], [18], [32], [33], [34], [35], [36], [37].”
InfluentialA reconfigurable battery system for a Tesla Model Y: Package and efficiency analysis
Wiedenmann, A., Estaller, J., Buberger, J., Grupp, W., Kuder, M., Neve, A., & Weyh, T. (2025) · eTransportation · doi:10.1016/j.etran.2025.100464 · Cited by 8
Komeda, S., Takuma, S., Ohnuma, Y., Gondo, R., Maezaki, D., & Taguchi, N. (2023) · IEEJ Journal of Industry Applications · doi:10.1541/ieejjia.22004964 · Cited by 6
Yuan, J., Poorfakhraei, A., Zhang, Y., Fang, G., & Emadi, A. (2024) · IEEE Journal of Emerging and Selected Topics in Industrial Electronics · doi:10.1109/jestie.2024.3495665 · Cited by 6
“First, PFC and dc voltage regulation need to be achieved simultaneously in the single ac/dc converter, which adds control complication [9].”
Self-citationKarneddi, H., Ronanki, D., & Rodríguez, J. (2025) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2025.3561869 · Cited by 7
“These chargers convert EVs into decentralized energy sources and can supply stored energy back to the grid through the V2G functionality, which is particularly useful during peak demand periods [6], [7], [8].”
Cuma, M. U., & Savrun, M. M. (2021) · Çukurova Üniversitesi Mühendislik Fakültesi Dergisi · doi:10.21605/cukurovaumfd.1048344 · Cited by 6
“In addition, the topology is able to reconfigure by bypassing one leg in order to operate as an Hbridge inverter to supply other loads [20].”
BackgroundKomeda, S., Takuma, S., & Ohnuma, Y. (2022) · International Power Electronics Conference (IPEC) · doi:10.23919/ipec-himeji2022-ecce53331.2022.9806911 · Cited by 6
“Introduction Isolated ac-dc converters are applied as an on-board battery charger in electric vehicles (EVs) applications [1].”
BackgroundA Novel Buck-Boost Derived PFC Converter for EV Charging
Kumar, G. K. N., Verma, A. K., & Mathuria, K. (2022) · Annual Conference of the IEEE Industrial Electronics Society (IECON) · doi:10.1109/iecon49645.2022.9969116 · Cited by 7
Performance Evaluation of an RL-Aided DAB-Based EV Charger Control
Mahazabeen, M., Abianeh, A. J., Ebrahimi, S., & Ferdowsi, F. (2022) · North American Power Symposium (NAPS) · doi:10.1109/naps56150.2022.10012228 · Cited by 8
“the EV industry due to their cost efficiency and simple hardware configuration comparing to the off-board chargers [5] [6].”
BackgroundANN Based Three Phase Full Bridge Bidirectional Charger in V2G-G2V Mode for EV Charging Application
Dixit, A., Swarnkar, P., & Nema, R. (2023) · IEEE International Conference on Renewable Energy and Sustainable E-Mobility (RESEM) · doi:10.1109/resem57584.2023.10236155 · Cited by 6
“The AC-DC controller performs the task of taking care of reactive power [25].”
BackgroundNew 600V GaN Single-Stage Isolated Bidirectional 400V Input Three-Phase PFC Rectifier
Menzi, D., Kolar, J. W., Sarnago, H., Lucía, Ó., & Huber, J. (2023) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce53617.2023.10362864 · Cited by 13
“…400 V three-phase mains (565 V peak value of the line-to-line voltages) are two-stage systems that comprise a PFC ac-dc rectifier front-end and an isolated dc-dc converter with a high-frequency (HF) transformer; typical applications are, e.g., EV chargers [1] or datacenter power supplies [2].”
BackgroundA 5kW Bidirectional Isolated On-Board EV Battery Charger Using Hybrid PFC/Inverter
Dabbagh, A. H., Arvani, H., & Afjei, E. S. (2022) · Iranian Conference on Electrical Engineering · doi:10.1109/icee55646.2022.9827002 · Cited by 8
An On-Board Charging System for Light EVs with G2V and V2G Power Transfer Capability
Gupta, J., & Singh, B. (2022) · IEEE IAS Global Conference on Emerging Technologies (GlobConET) · doi:10.1109/globconet53749.2022.9872502 · Cited by 6
“It is noteworthy that, the onboard chargers (OBC) have wider acceptability among automotive industries and EVs users, as they provide convenience to the vehicle user to charge their vehicles directly through AC supply systems and ensure low cost of implementation to the automotive industries [4].”
BackgroundZhang, C., Jasni, J., Radzi, M. A. M., Azis, N. B., & He, X. (2023) · Ionics · doi:10.1007/s11581-023-05062-3 · Cited by 7
Integrated Magnetic Choke Solutions for Compact Passive Electromagnetic Interference Filters
Dwiza, B., Singh, S., Gorla, N. B. Y., et al. (2025) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2025.3570156 · Cited by 5
“T HE dc–dc switched-mode power converters have always been a crucial part of power conversion systems [1], [2], [3], [4].”
A User-Centric Game for Balancing V2G Benefits With Battery Degradation of Electric Vehicles
Mallick, A., Pantazis, G., Esfahani, P. M., & Grammatico, S. (2025) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2025.3593837 · Cited by 8
“For this purpose, we choose a level-2 three-phase on-board charger of power rating 22 kW, which Eaton and other major manufacturers currently manufacture [28].”
ZVS Turn-on integrated Triangular Current Mode Three-phase PFC for EV On-board Chargers
Sun, J. L., Wu, Y., Soeiro, T. B., Qin, Z., & Bauer, P. (2022) · International Power Electronics and Motion Control Conference (EPE-PEMC) · doi:10.1109/pemc51159.2022.9962857 · Cited by 5
Menzi, D., Weihe, S., Anderson, J. A., Kasper, M., Huber, J., & Kolar, J. W. (2023) · IEEE ... Workshop on Control and Modeling for Power Electronics · doi:10.1109/compel52896.2023.10221163 · Cited by 5
“OBCs are required to feature high efficiency, high gravimetric and volumetric power densities [2], as well as bidirectional power flow capability for feeding power back to the grid in vehicle-to-grid (V2G) applications [2], [3].”
BackgroundBhati, N., & Kalla, U. K. (2021) · IEEE International Conference on Smart Technologies for Power, Energy and Control (STPEC) · doi:10.1109/stpec52385.2021.9718738 · Cited by 6
Jerez, A. L. P., Mori, M. F., Flexer, V., et al. (2022) · Materials · doi:10.3390/ma15248856 · Cited by 5
“The gradual replacement of internal combustion engine vehicles with cleaner means of transportation, such as electric vehicles, is another crucial step for our society [2,3].”
BackgroundA Turn-Ratio-Changing Half-Bridge CLLC DC–DC Bidirectional Battery Charger Using a GaN HEMT
Shieh, Y.-T., Wu, C.-C., Jeng, S.-L., Liu, C.-Y., Hsieh, S.-Y., Haung, C.-C., Shieh, W.-Y., Chieng, W.-H., & Chang, E. Y. (2023) · Energies · doi:10.3390/en16165928 · Cited by 5
Solar Photovoltaic Charging of Electric Vehicle and V2G for Indian Electricity Demand Scenario
Suraj, S., Manjarekar, N. S., & Barik, S. (2023) · Lecture notes in electrical engineering · doi:10.1007/978-981-99-6151-1_12 · Cited by 5
Funatsu, S., Matsumori, H., Kosaka, T., et al. (2023) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce53617.2023.10362905 · Cited by 5
EV Battery Charging Converters with Wide Output DC Voltage Range
Nadeem, M. M., Blinov, A., & Vinnikov, D. (2023) · IEEE International Scientific Conference on Power and Electrical Engineering of Riga Technical University (RTUCON) · doi:10.1109/rtucon60080.2023.10412960 · Cited by 6
“This function is necessary to provide a controllable DC voltage and meet the harmonic requirements of the grid [15].”
BackgroundAbdel-Wahed, A. T., Abdel-Khalik, A. S., Hamad, M. S., Massoud, A. M., & Ahmed, S. (2024) · International Conference on Smart Grid and Renewable Energy (SGRE) · doi:10.1109/sgre59715.2024.10428879 · Cited by 5
“This step is chief to reduce greenhouse gas emissions, the leading cause of pollution, as EVs use clean energy [1].”
BackgroundPanhwar, I. H., Mekhilef, S., Seyedmahmoudian, M., et al. (2025) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2025.3567490 · Cited by 5
“The EV chargers are designed to operate in unidirectional and bidirectional power flow modes [5].”
Converter Topology Comparison for a Two-Stage Level-2 Onboard Charger in 800-V EV Powertrains
Pradhan, R., Narimani, M., & Emadi, A. (2022) · Annual Conference of the IEEE Industrial Electronics Society (IECON) · doi:10.1109/iecon49645.2022.9968504 · Cited by 5
Self-citationQayamuddin, M., Sarwar, M., Siddiqui, A. S., Haque, A., & Warsi, N. A. (2023) · Energy Storage · doi:10.1002/est2.463 · Cited by 6
Optimized control strategy of totem-pole PFC converter based on two-stage charger
Zhu, X., Wu, Y. F., Tan, J., Chen, C., Xue, G., Xu, Z., Niu, W., & Sun, J. (2024) · Journal of Physics Conference Series · doi:10.1088/1742-6596/2683/1/012028 · Cited by 5
A Review of Three Phase AC-DC Power Factor Correction Converters for Electric Vehicle Fast Charging
Mollahasanoğlu, M., & Okumuş, H. İ. (2022) · European Journal of Science and Technology · doi:10.31590/ejosat.1041081 · Cited by 6
“On-board chargers are slow because they operate at lower currents (Metwly et al., 2020; Sam et al., 2021; Yuan et al., 2021).”
BackgroundFlyback Converters for Electric Vehicle Applications- A Review
Bose, A., & Sekhar, P. C. (2025) · IEEE International Conference on Industrial Electronics: Developments & Applications (ICIDeA) · doi:10.1109/icidea64800.2025.10963090 · Cited by 4
“These chargers are limited by the size, control complexity, and poor efficiency, concerning low powered EVs [18], [19].”
Sekar, S., Tiwana, A. S., & Singh, K. (2025) · Green Energy and Intelligent Transportation · doi:10.1016/j.geits.2025.100333 · Cited by 8
Ruttala, S., Nakka, J., Kumar, B., & Naresh, S. V. K. (2026) · IEEE Access · doi:10.1109/access.2026.3664945 · Cited by 9
“Three-phase bidirectional onboard chargers offer a promising alternative by enabling higher power transfer, improved efficiency, and better power quality [92].”
Miah, M. S., Shah, R., Aslam, M. U., Amjady, N., Walker, S. L., Terzija, V. V., Dehghan, S., & Mithulananthan, N. (2026) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2026.116858 · Cited by 5
Yuan, Z., Chen, P., Wu, Z., Li, H., Yang, Z., Zhao, S., Yu, Z., Ding, L., Wang, L., & Huo, W. (2023) · IEEE International Electrical and Energy Conference (CIEEC) · doi:10.1109/cieec58067.2023.10166724 · Cited by 4
Software-Based Power Sharing Control in Parallel Dual-Output Phase-Shift Full-Bridge Converters
Pittala, L. K., Geng, J., Baldisserri, S., Mandrioli, R., Ricco, M., & Grandi, G. (2024) · IEEE International Conference on Compatibility, Power Electronics and Power Engineering · doi:10.1109/cpe-powereng60842.2024.10604390 · Cited by 6
“Unlike traditional unidirectional converters, bidirectional converters, specifically isolated DC/DC converters, offer flexibility for various applications such as electric vehicles, smart grids, uninterruptible power supplies, aerospace, smart transformer, and renewable energy systems [2]–[7].”
BackgroundYao, Y., La, Y., Shen, S., et al. (2024) · Energies · doi:10.3390/en17174507 · Cited by 4
Magnetically Coupled Interleaved Buck Integrated On-Board Charger for Light Electric Vehicles
Afriyie, D., Khan, A. A., & Iqbal, M. T. (2025) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2025.3581482 · Cited by 4
“Although reliable power supply methods have been developed, the availability of efficient and cost-effective chargers hinders the full adoption of EVs [6], [7], [8].”
Alshammari, M. S., & Duffy, M. C. (2023) · IEEE Access · doi:10.1109/access.2023.3243131 · Cited by 5
“grid from the used on board battery charger of EVs [6], [7].”
MethodGaN-based Multiport Resonant Converter for Automotive Applications
Groon, F., Pereira, T., Beiranvand, H., Schikowski, S., Metschies, D., & Liserre, M. (2023) · Conference proceedings/Conference proceedings - IEEE Applied Power Electronics Conference and Exposition · doi:10.1109/apec43580.2023.10131146 · Cited by 4
“The EVs performance and range are a function of power converter, battery pack efficiency, volume and weight [1].”
BackgroundThe ENERGY ECS Project: Smart and Secure Energy Solutions for Future Mobility
Romani, A., Crescentini, M., Rusu, C., Staaf, H., Ambrosio, M., Chiaberge, M., Piacibello, A., Pirola, M., Giliberti, G., Cappelluti, F., et al. (2023) · AEIT International Conference of Electrical and Electronic Technologies for Automotive (AEIT AUTOMOTIVE) · doi:10.23919/aeitautomotive58986.2023.10217190 · Cited by 6
“The OBC requirements in terms of efficiency, power handling and size (that strongly affects the design of the cooling systems) are above the current state of the art of commercial products and literature solutions [17][18].”
BackgroundKwak, B. (2023) · Energy and Power Engineering · doi:10.4236/epe.2023.1510019 · Cited by 4
Jia, P., Xie, J., Liu, M., Zhang, Y., Xing, Y., & Qiu, K. (2024) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2024.3451497 · Cited by 4
“I SOLATED dc/dc converters have been widely applied in on board charger (OBC), energy storage systems (ESSs), new energy generation systems, and aerospace applications, etc. [1], [2].”
BackgroundPhase-shifted Dual Active Bridge Converter Based EV Charger Architecture with G2V and V2G Modes
Kulkarni, S., & Thale, S. (2024) · IEEE International Conference on Electronics, Computing and Communication Technologies (CONECCT) · doi:10.1109/conecct62155.2024.10677167 · Cited by 5
“Safayatullah et al. [6] provided a review of converter topologies for fast charging of EVs, while [7] reviewed bi-directional on-board chargers (OBC).”
BackgroundMethodNayak, G., & Dasgupta, A. (2024) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2024.3477474 · Cited by 5
“In recent literature, this topology has been presented as a single-stage as well as a two-stage unit based on the control objectives [6].”
Joy, A. V., Kangappadan, E. T., Prasad, A., Nandakishore, K. S., & Ismail, T. (2024) · International Conference on Advancement in Renewable Energy and Intelligent Systems (AREIS) · doi:10.1109/areis62559.2024.10893645 · Cited by 4
A SiC-Based Hybrid PFC-Inverter for On-board EV Chargers
Dabbagh, A. H., Arvani, H., Gholizadeh, H., & Afjei, E. S. (2022) · Power Electronics, Drive Systems, and Technologies Conference (PEDSTC) · doi:10.1109/pedstc53976.2022.9767296 · Cited by 6
Venkateshwarlu, S., Arandhakar, S., & Kumar, K. S. (2024) · E3S Web of Conferences · doi:10.1051/e3sconf/202447201021 · Cited by 7
Unbalanced Charging Operation for Dual-Channel Electric-Drive-Reutilized Onboard Charger
Cheng, X., Yu, F. Y., Liu, A., & Yin, Q. (2024) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2024.3407871 · Cited by 4
“In order to promote the usage, onboard chargers have been actively developed to feed EVs without regard for geographical limitations, providing a convenient charging option [2].”
Varun, S., & Bhongade, S. (2022) · Engergy systems in electrical engineering · doi:10.1007/978-981-19-0979-5_30 · Cited by 4
Thermal simulation of a 7kW interleaved module for fast automotive charger
Anoldo, L., Piccione, G. G., Mauromicale, G., Sitta, A., Fazio, E., Calabretta, M., Lionetto, A., Messina, A. A., Guardo, M. D., & Patanè, S. (2021) · IEEE International Conference on Environment and Electrical Engineering and IEEE Industrial and Commercial Power Systems Europe (EEEIC / I&CPS Europe) · doi:10.1109/eeeic/icpseurope51590.2021.9584683 · Cited by 4
Funatsu, S., Matsumori, H., Kosaka, T., Matsui, N., Nakamura, K., Takahashi, M., Taguchi, S., & Saha, S. (2025) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2025.3600210 · Cited by 3
“1 and 2 respectively [7], [8], [9], [10], [11], [12], [13].”
Prabhakar, S., Chakraborty, S., Deshmukh, N., & Anand, S. (2025) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2025.3606336 · Cited by 3
“Techniques such as adopting high battery voltages, utilizing wide bandgap (WBG) devices, optimizing magnetic designs, and implementing advanced thermal management strategies have been widely employed to develop compact and cost-effective OBCs [3], [4], [5], [6], [7], [8], [9].”
Are electric vehicles a viable alternative to home batteries? An Australian case study
Geach, C. R., Aldaadi, M., & Verbič, G. (2026) · Journal of Energy Storage · doi:10.1016/j.est.2026.120721 · Cited by 3
Gang, Z., Wu, Y., Xu, J., & Soeiro, T. B. (2024) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2024.3395706 · Cited by 5
“High efficiencyhasbeenobservedinthetwo-levelVSCutilizing GaNorSiC MOSFET switches while operating at hard-switching pulsewidth modulation (PWM) with a fixed switching frequency set above the audible frequency range [2], [6].”
BackgroundComparative Analysis of Permanent Magnet Synchronous Motor Drive Controllers for Electric Vehicles
Priya, B., & Kaur, R. (2024) · IEEE International Conference on Electronics, Computing and Communication Technologies (CONECCT) · doi:10.1109/conecct62155.2024.10677258 · Cited by 3
Derakhshan, S., & Lam, J. C. W. (2025) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2025.3552505 · Cited by 6
“In addition, single-stage designs require sophisticated optimization across a wide range of specifications [5], [6].”
InfluentialReview on Advancements in Bidirectional On-Board Chargers for Electric Vehicles
Prajapati, R. K., & Kumar, R. (2024) · IEEE Power India International Conference · doi:10.1109/piicon63519.2024.10995219 · Cited by 4
“Table 4 indicates that while most commercially available PFC converters approach 99% efficiency, achieving high power density at elevated power ratings remains challenging [27].”
An Isolation Circuit based Charging and Discharging Model of On-Board Charger in Electric Vehicle
Podamekala, V. K., & Sandeep, V. (2022) · IEEE International Conference on Sustainable Energy and Future Electric Transportation (SEFET) · doi:10.1109/sefet55524.2022.9909244 · Cited by 3
“Onboard and offboard chargers are the different sorts of battery chargers [3-5].”
BackgroundActive Power Decoupling Strategy for Single Phase AC Charging Using a Dual Inverter Drive
Perera, C., Pathmanathan, M., Viana, C. C. D., & Lehn, P. W. (2023) · Conference proceedings/Conference proceedings - IEEE Applied Power Electronics Conference and Exposition · doi:10.1109/apec43580.2023.10131375 · Cited by 3
“However, single stage OBCs [6]-[10] are still mainly limited to academic research [5].”
BackgroundA., A. F. P., Ramchand, R., & Nair, H. S. (2023) · International Conference on Power, Instrumentation, Control and Computing (PICC) · doi:10.1109/picc57976.2023.10142639 · Cited by 5
“Design and control are simple with better efficiency and lesser devices [8].”
BackgroundInfluentialA Single-/Three-phase Compatible V2G Bidirectional On-Board Charger with Reconfigurable Structure
Chan, Y. P., Li, Q., Ponnuvelu, B., & Li, R. T.-H. (2023) · International Conference on Power Electronics and ECCE Asia (ICPE-ECCE Asia) · doi:10.23919/icpe2023-ecceasia54778.2023.10213747 · Cited by 3
Kiffe, A., & Hoffstadt, T. (2023) · European Conference on Power Electronics and Applications · doi:10.23919/epe23ecceeurope58414.2023.10264254 · Cited by 3
Clavero, L., Gaona, D. E., & Wijekoon, T. (2023) · Annual Conference of the IEEE Industrial Electronics Society (IECON) · doi:10.1109/iecon51785.2023.10312576 · Cited by 3
“In this context, single stage AC/DC converters are becoming increasingly popular due to the promise of compact size achieved by the reduction of components, and the elimination of required dc link electrolytic capacitors, which can improve reliability [2].”
BackgroundDesign and Implementation of CLLLC Bidirectional Converter with Wide Voltage Range on Low Side
Li, J., Lee, W.-H., Chen, J.-F., & Liang, T. (2023) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce53617.2023.10362785 · Cited by 3
“A comparison of EV charging levels is listed in TABLE I [7], [8].”
BackgroundA new Interleaved Full-Bridge Converter for AC battery
Anh, D. T., Le, Q. N., Nguyen, T. L., et al. (2023) · International Conference on Control, Automation and Information Sciences (ICCAIS) · doi:10.1109/iccais59597.2023.10382330 · Cited by 3
“For example, a home in the US, the country with the highest capacity of SLBs, could only supply the single-phase grid for the power rate from 0 to 7kW [5].”
BackgroundChothani, N. (2024) · International Conference on Integrated Circuits and Communication Systems (ICICACS) · doi:10.1109/icicacs60521.2024.10498508 · Cited by 3
“Different challenges on different topologies based on thermal effect, wide band gap systems, and futuristic systems like wireless charging are also discussed sharply based on different topologies [5].”
BackgroundOptimized EV On-Board Charging Power Converter Using Hybrid DCX-DAB Topology
Sarnago, H., & Lucía, Ó. (2024) · Conference proceedings/Conference proceedings - IEEE Applied Power Electronics Conference and Exposition · doi:10.1109/apec48139.2024.10509177 · Cited by 4
“On-board chargers (OBCs) [3-6] are essential to ensure fast and efficient charge regardless the grid voltage, number of grid phases or the battery charge status. electrical safety, while bidirectional capability is also necessary to supply home loads and serve as a home power hub.”
BackgroundOn-Board AC Charging Topology Integrated with Electric Vehicle Motor Drive System
Azam, M. K. M. B., Ahmed, A., Islam, M. M., Dristy, A. H., Siddiquee, A., Sozer, Y., & Kisacikoglu, M. C. (2024) · Conference proceedings/Conference proceedings - IEEE Applied Power Electronics Conference and Exposition · doi:10.1109/apec48139.2024.10509402 · Cited by 7
“In today's transportation world, Electric Vehicles (EVs) stand for a cleaner, greener future by reducing our dependence on fossil fuels [1-2].”
BackgroundIntegrated on-board electric vehicle battery charger with multifunctional features
Gupta, J., Maurya, R., & Arya, S. R. (2024) · Australian Journal of Electrical & Electronics Engineering · doi:10.1080/1448837x.2024.2350838 · Cited by 4
Mustafa, U., Kougioulis, I., Watson, A. J., Wheeler, P. W., & Ahmed, M. R. (2024) · IEEE Transportation Electrification Conference and Expo · doi:10.1109/itec60657.2024.10598844 · Cited by 4
“The typical onboard charger is rated at 6.6kW which takes 6-10 hours to charge a vehicle fully [2] [3].”
BackgroundDesign and Simulation of a 10 kW Bidirectional EV Fast Charger Based on V2G Technology
Yang, R., & Yang, F. (2024) · IEEE Transportation Electrification Conference and Expo, Asia-Pacific (ITEC Asia-Pacific) · doi:10.1109/itecasia-pacific63159.2024.10738656 · Cited by 3
The Coordinated Control Strategy of Cascaded Voltage-Source Converter
Shen, H., Kuang, Q., Chen, K., Sun, X., & Guan, K. (2025) · Electronics · doi:10.3390/electronics14030576 · Cited by 3
Sora, J., & Serban, I. (2025) · doi:10.1109/optim-acemp62776.2025.11075280 · Cited by 3
“Dual active bridge (DAB) converters have gained traction in EV charging applications due to galvanic isolation, bidirectional power flow capabilities, and high power density [2].”
Boost Operation of a Dual-Active-Bridge AC-DC Converter with an Active Energy Buffer
Komeda, S., Takuma, S., & Ohnuma, Y. (2022) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce50734.2022.9948064 · Cited by 3
“Nowadays, a battery charger on electric vehicle (EVs) is one of the attractive application of an isolated ac-dc converters [1], [2].”
BackgroundCircuit Configuration of a Reduced Count Modular Multi-Level Inverter
Zare, H., & Asgharpour‐Alamdari, H. (2021) · International Journal of Electronics · doi:10.1080/00207217.2021.1966670 · Cited by 5
“These applications include: electric-vehicles (Yuan et al., 2021) Active Filters (AF) (Hoon et al.”
BackgroundGuo, Z., Kobayashi, T., & Kinoshita, T. (2024) · International Conference on Renewable Energy Research and Applications (ICRERA) · doi:10.1109/icrera62673.2024.10815584 · Cited by 2
Jena, P., Maurya, V. P., Singh, R. K., & Lal, V. N. (2024) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce55643.2024.10861084 · Cited by 2
Tintu George, T., & Sahayadhas, A. (2025) · doi:10.1109/areev64307.2025.10925198 · Cited by 2
“In reference [5], a system for the dynamic regulation of power in battery chargers is introduced, which adjusts the charging current for batteries.”
Single Phase Fast EV Charger Based on Grid Connected Quasi Z-Source Inverter
Zarbil, M. S., Patra, S., & Khadem, S. (2024) · International Conference on Smart Power & Internet Energy Systems (SPIES) · doi:10.1109/spies63782.2024.10982843 · Cited by 3
Metadata
- Authors
- Yuan, J., Dorn-Gomba, L., Callegaro, A. D., Reimers, J., & Emadi, A.
- Affiliations
- McMaster University (CA)
- Venue
- IEEE Access
- Published
- 2021
- Volume
- 9
- Pages
- 51501-51518
- ISSN
- 2169-3536 (ISSN-L)
- OpenAlex
- W3147908447
- Cited by
- 390
- References
- 159
- Citations by year
- 2026: 48 · 2025: 94 · 2024: 100 · 2023: 83 · 2022: 49 · 2021: 16
- FWCI
- 18.20
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Locations
- IEEE Access (publishedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Advanced DC-DC Converters
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Wireless Power Transfer Systems
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Electric Vehicles and Infrastructure
- Keywords
- electric vehicles, bidirectional power flow, power electronics topology, two-stage converter, single-stage converter, wide bandgap semiconductors, thermal management, wireless charging, charging efficiency, power density
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol and qwen3.8-omni-flash).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.