An Overview of 800 V Passenger Electric Vehicle Onboard Chargers: Challenges, Topologies, and Control
Open accessThe DOI matches its Crossref record; 60 of the 60 references it cites were found in a registry or an index.
Abstract
Ultrafast charging can help increase the adoption of battery electric vehicles (BEVs) as it solves the prime issues of range anxiety and long charging time. However, for conventional 400 V battery systems, these high charging currents can become infeasible due to cable limitations and thermal issues. Fortunately, 800 V systems can provide higher charging power capacity at lower current levels, better enabling ultrafast charging. The emerging shift to 800 V systems from 400 V systems requires careful design considerations for the on-board charger (OBC). This article fills a gap in the literature by performing a comprehensive review of state-of-the-art 800 V passenger BEV OBC topologies and control, focusing primarily on 1-phase topologies as the majority of residential charging connections are 1-phase. This article also reviews the main design challenges for 800 V OBCs and relevant industrial products, and provides a discussion of related future trends.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Citations
Cites
The state of the art of electric, hybrid, and fuel cell vehicles
Chan, C. C. (2007) · Proceedings of the IEEE · doi:10.1109/jproc.2007.892489 · Cited by 1,987 · cited 1×
“Battery electric vehicles (BEVs) are excellent alternatives to internal combustion engine vehicles due to their high efficiency, zero tailpipe emissions, and reduced reliance on fossil fuels [1], [2], [3].”
BackgroundZhao, B., Song, Q., Liu, W., & Sun, Y. (2014) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2013.2289913 · Cited by 1,886 · cited 1×
“This topology merges a dual active-bridge (DAB) [64], [65] with a series-resonant diode rectifier stage composed of diodes and the resonant tank, enabling the utilization of standard 650 V Si devices which inherently ensures optimized power processing and the appropriate output voltage distribution…”
BackgroundA Review of Three-Phase Improved Power Quality AC–DC Converters
Singh, B., Singh, B. N., Chandra, A., Al-Haddad, K., Pandey, A., & Kothari, D. P. (2004) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2004.825341 · Cited by 1,728 · cited 1×
“Furthermore, [27], [28], [29] review OBCs in general, but do not focus on the 800 V challenges.”
BackgroundPerformance characterization of a high-power dual active bridge DC-to-DC converter
Kheraluwala, M. N., Gascoigne, R. W., Divan, D. M., & Baumann, E. D. (1992) · IEEE Transactions on Industry Applications · doi:10.1109/28.175280 · Cited by 1,496
The 2018 GaN power electronics roadmap
Amano, H., Baines, Y., Beam, E., Borga, M., Bouchet, T., Chalker, P. R., Charles, M., Chen, K. J., Chowdhury, N., Chu, R., et al. (2018) · Journal of Physics D: Applied Physics · doi:10.1088/1361-6463/aaaf9d · Cited by 1,313 · cited 2×
“Commercial GaN semiconductors are currently rated from 80V-650V [51], [52], and thus 800 V OBC topologies that eliminate the need for 1200 V rated devices can benefit from GaN technology.”
BackgroundA review of single-phase improved power quality ac~dc converters
Singh, B., Singh, B. N., Chandra, A., Al-Haddad, K., Pandey, A., & Kothari, D. P. (2003) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2003.817609 · Cited by 1,297
Hannan, M. A., Hoque, M. M., Hussain, A., Yusof, Y., & Ker, P. J. (2018) · IEEE Access · doi:10.1109/access.2018.2817655 · Cited by 988 · cited 2×
“For example, a typical 800 V OBC may require a wider output voltage range such as 500-880 V [45], [46] compared to a 400 V OBC with half the number of battery cells in series, which would require an output range of 250-440 V [45], [46], [47], where the battery voltage varies within these ranges due…”
BackgroundEfficiency-Optimized High-Current Dual Active Bridge Converter for Automotive Applications
Krismer, F., & Kolar, J. W. (2012) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2011.2112312 · Cited by 747 · cited 1×
“This topology merges a dual active-bridge (DAB) [64], [65] with a series-resonant diode rectifier stage composed of diodes and the resonant tank, enabling the utilization of standard 650 V Si devices which inherently ensures optimized power processing and the appropriate output voltage distribution…”
BackgroundAn LLC Resonant DC–DC Converter for Wide Output Voltage Range Battery Charging Applications
Musavi, F., Craciun, M., Gautam, D. S., Eberle, W., & Dunford, W. G. (2013) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2013.2241792 · Cited by 498 · cited 1×
“The PFC part controls the link voltage, and the link capacitor is the primary energy storage which aids in reducing the output voltage ripple of the PFC converter [40], [41].”
BackgroundShenoy, P. S., Kim, K. A., Johnson, B. B., & Krein, P. T. (2013) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2012.2211082 · Cited by 460 · cited 1×
“Reference [61] proposes a low cost and modular onboard charger DC/DC topology incorporating differential power processing [60], [62], [63] for high efficiency and power density, as shown in Fig.”
800-V Electric Vehicle Powertrains: Review and Analysis of Benefits, Challenges, and Future Trends
Aghabali, I., Bauman, J., Kollmeyer, P. J., Wang, Y., Bilgin, B., & Emadi, A. (2021) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2020.3044938 · Cited by 434 · cited 2×
“These topologies may be modified for an 800 V BEV by doubling the transformer turns ratio [25], though this will increase the transformer core size, cost, and conduction losses [57], [58].”
BackgroundSelf-citationEvaluation and Application of 600 V GaN HEMT in Cascode Structure
Huang, X., Liu, Z., Li, Q., & Lee, F. C. (2014) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2013.2276127 · Cited by 415 · cited 1×
“Wide bandgap (WBG) devices, such as gallium nitride (GaN) and silicon carbide (SiC), are popular choices for OBCs due to diminished reverse recovery charge and increased electron mobility, leading to higher switching frequencies [49], [50].”
BackgroundMusavi, F., Eberle, W., & Dunford, W. G. (2011) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2011.2156753 · Cited by 376 · cited 1×
“The special feature of this control strategy is its ability to eliminate crossover distortion [59] which are present in [60].”
BackgroundGrid-Connected Integrated Battery Chargers in Vehicle Applications: Review and New Solution
Haghbin, S., Lundmark, S., Alakula, M., & Carlson, O. (2013) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2012.2187414 · Cited by 345 · cited 1×
“Furthermore, [27], [28], [29] review OBCs in general, but do not focus on the 800 V challenges.”
BackgroundJung, C. (2017) · IEEE Electrification Magazine · doi:10.1109/mele.2016.2644560 · Cited by 312
An Automotive Onboard 3.3-kW Battery Charger for PHEV Application
Gautam, D. S., Musavi, F., Edington, M., Eberle, W., & Dunford, W. G. (2012) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2012.2210259 · Cited by 274 · cited 1×
“The PFC part controls the link voltage, and the link capacitor is the primary energy storage which aids in reducing the output voltage ripple of the PFC converter [40], [41].”
BackgroundLee, J.-Y., Jeong, Y.-S., & Han, B.-M. (2011) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2010.2076311 · Cited by 270 · cited 1×
“Common choices for the isolated DC/DC converter are the LLC converter with full bridge rectifier (with soft switching capability over a wide voltage range) and the phase-shifted full-bridge (PSFB) converter [38], [39].”
BackgroundDickerman, L., & Harrison, J. (2010) · IEEE Power and Energy Magazine · doi:10.1109/mpe.2009.935553 · Cited by 231 · cited 1×
“Battery electric vehicles (BEVs) are excellent alternatives to internal combustion engine vehicles due to their high efficiency, zero tailpipe emissions, and reduced reliance on fossil fuels [1], [2], [3].”
BackgroundA Wide-Range High-Voltage-Gain Bidirectional DC–DC Converter for V2G and G2V Hybrid EV Charger
Heydari-doostabad, H., & O'Donnell, T. (2022) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2021.3084181 · Cited by 196
Performance of Power-Limited Differential Power Processing Architectures in Mismatched PV Systems
Olalla, C., Deline, C., Clement, D., Levron, Y., Rodriguez, M., & Maksimovic, D. (2015) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2014.2312980 · Cited by 180 · cited 2×
“Reference [61] proposes a low cost and modular onboard charger DC/DC topology incorporating differential power processing [60], [62], [63] for high efficiency and power density, as shown in Fig.”
BackgroundAn Electrolytic Capacitorless Bidirectional EV Charger for V2G and V2H Applications
Kwon, M., & Choi, S. (2017) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2016.2630711 · Cited by 177 · cited 2×
“Most OBC designs focus on grid-to-vehicle (G2V) charging, but it can be beneficial to have flexible charging options such as vehicle-to-grid (V2G), vehicle-to-home (V2H), and vehicle-to-vehicle (V2V) [89], [90].”
BackgroundOn-Board Chargers for High-Voltage Electric Vehicle Powertrains: Future Trends and Challenges
Pradhan, R., Keshmiri, N., & Emadi, A. (2023) · IEEE Open Journal of Power Electronics · doi:10.1109/ojpel.2023.3251992 · Cited by 142 · cited 1×
“…[25], which provides a comprehensive analysis of how all major powertrain components will change in an 800 V BEV compared to a 400 V BEV, and [26], which provides an overview of 800 V BEV charging, including charging infrastructure and regulatory standards, where the OBC discussion focuses…”
BackgroundA critical review of electric vehicle charging using solar photovoltaic
Bhatti, A. R., Salam, Z., Aziz, M. J. A., & Yee, K. P. (2015) · International Journal of Energy Research · doi:10.1002/er.3472 · Cited by 136 · cited 1×
“BEVs are usually equipped with two charging outlets: one for standard (OBC) Level 1 and Level 2 charging with a low current connection, and another for fast (offboard) Level 3 DC charging with a high current connection [30], [31], [32].”
BackgroundA High Power Density Wide Range DC–DC Converter for Universal Electric Vehicle Charging
Mukherjee, S., Ruiz, J. M., & Barbosa, P. (2023) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2022.3217092 · Cited by 133 · cited 5×
“9 shows an LCL-T isolated DC/DC converter for onboard charging with reduced capacitor RMS current stress, which focuses on efficiency improvement for 800 V charging [49].”
BackgroundMethodInfluentialDifferential Power Processing for DC Systems
Shenoy, P. S., & Krein, P. T. (2012) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2012.2214402 · Cited by 116 · cited 1×
“Reference [61] proposes a low cost and modular onboard charger DC/DC topology incorporating differential power processing [60], [62], [63] for high efficiency and power density, as shown in Fig.”
Soft Switching Multiphase Interleaved Boost Converter With High Voltage Gain for EV Applications
Ahmed, N. A., Alajmi, B. N., Abdelsalam, I., & Marei, M. I. (2022) · IEEE Access · doi:10.1109/access.2022.3157050 · Cited by 96 · cited 4×
“Reference [33] proposed a non-isolated structure which might have the disadvantage of leakage current, however, this converter attains wide soft switching range and lower current ripple.”
BackgroundMethodInfluentialDutta, S., Gangavarapu, S., Rathore, A. K., Singh, R. K., Mishra, S. K., & Khadkikar, V. (2022) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2022.3148969 · Cited by 91 · cited 2×
“Recent research is moving towards single-stage topologies [34], [35], [36], [88] as the DC link capacitor is a heavy component which adds to the weight of the system and affects the power density.”
BackgroundSelf-citationA High Efficiency High Density DC/DC Converter for Battery Charger Applications
Jin, F., Nabih, A., Chen, C., Chen, X., Li, Q., & Lee, F. C. (2021) · 2021 IEEE Applied Power Electronics Conference and Exposition (APEC) · doi:10.1109/apec42165.2021.9487108 · Cited by 89
New Perspectives for Vehicle-to-Vehicle (V2V) Power Transfer
Sousa, T. J. C., Monteiro, V., Fernandes, J. C. A., Couto, C., Melendez, A. A. N., & Afonso, J. L. (2018) · IECON 2018 - 44th Annual Conference of the IEEE Industrial Electronics Society · doi:10.1109/iecon.2018.8591209 · Cited by 79 · cited 1×
“Recent research is moving towards single-stage topologies [34], [35], [36], [88] as the DC link capacitor is a heavy component which adds to the weight of the system and affects the power density.”
BackgroundAn Analysis of Consumer Incentives in Support of Electric Vehicle Uptake: An Australian Case Study
Broadbent, G. H., Metternicht, G. I., & Drozdzewski, D. (2019) · World Electric Vehicle Journal · doi:10.3390/wevj10010011 · Cited by 71 · cited 1×
“However, there are still some practical challenges impeding increased BEV adoption, such as cost, long charging times, and limited driving ranges [6].”
BackgroundLithium-Ion Battery Lifetime Extension With Positive Pulsed Current Charging
Huang, X., Meng, J., Liu, W., Ru, F., Duan, C., Xu, X., Stroe, D., & Teodorescu, R. (2023) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2023.3250850 · Cited by 66 · cited 2×
“…generally has excess capacity at night [17], advantageous for the vehicle’s battery lifetime because it can be shortened by excessive fast-charging events [18], and advantageous for the environment as the grid often has a lower carbon intensity overnight compared to peak load hours of the day [19].”
BackgroundAnalysis of a Multilevel Dual Active Bridge (ML-DAB) DC-DC Converter Using Symmetric Modulation
Moonem, M. A., Pechacek, C., Hernandez, R., & Krishnaswami, H. (2015) · Electronics · doi:10.3390/electronics4020239 · Cited by 66
Mobarak, M. H., & Bauman, J. (2019) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2019.2946063 · Cited by 65 · cited 1×
“This is advantageous for the grid because it generally has excess capacity at night [17], advantageous for the vehicle’s battery lifetime because it can be shortened by excessive fast-charging events [18], and advantageous for the environment as the grid often has a lower carbon intensity overnight…”
BackgroundSelf-citationNew Combined OBC and LDC System for Electric Vehicles With 800 V Battery
Lee, D.-W., Lee, B.-S., Ahn, J.-H., Kim, J., & Kim, J.-K. (2022) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2022.3148730 · Cited by 64 · cited 4×
“Reference [69] uses a single multiwinding transformer to connect the sec-ondaries of both OBC and APM, meaning it can charge the high voltage and low voltage battery at the same time.”
BackgroundMethodInfluentialReliability issues of GaN based high voltage power devices
Wuerfl, J., Treidel, E. B., Brunner, F., Cho, E.-M., Hilt, O., Ivo, P., Knauer, A., Kurpas, P., Lossy, R., Schulz, M., et al. (2011) · Microelectronics Reliability · doi:10.1016/j.microrel.2011.07.017 · Cited by 62 · cited 1×
“To aid in this direction, higher power rated GaN devices would reduce the need for paralleling, and further improvements should be made on reliability issues so that they are more robust for high power application [85].”
BackgroundLow Voltage Charging Technique for Electric Vehicles With 800 V Battery
Kim, J., Lee, B.-S., Kwon, D.-H., Lee, D.-W., & Kim, J.-K. (2021) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2021.3109526 · Cited by 60 · cited 5×
“Reference [2] used a 400 V optimized OBC to charge 800 V batteries using a battery selection circuit.”
BackgroundMethodInfluentialState-of-art of Metamaterials with Negative Poisson’s Ratio
Yu, J. (2018) · Journal of Mechanical Engineering · doi:10.3901/jme.2018.13.001 · Cited by 50
Cesiel, D., & Zhu, C. (2017) · IEEE Electrification Magazine · doi:10.1109/mele.2016.2644265 · Cited by 44 · cited 5×
“OBC topology for GM’s chevrolet volt [47]. thus far limited to 650 V [51], [52].”
BackgroundMethodInfluentialLeakage Current Issue of Non-Isolated Integrated Chargers for Electric Vehicles
Zhang, Y., Yang, G., He, X., Elshaer, M., Perdikakis, W., Li, H., Yao, C., Wang, J., Zou, K., Xu, Z., et al. (2018) · 2018 IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce.2018.8558133 · Cited by 41 · cited 1×
“In either case, the battery and AC grid are usually isolated to avoid the common mode leakage current [37].”
BackgroundSingle-Stage EV On-Board Charger with Single- and Three-Phase Grid Compatibility
Kim, H., Park, J., Kim, S., Hakim, R. M., Kieu, H.-P., & Choi, S. (2021) · Conference proceedings/Conference proceedings - IEEE Applied Power Electronics Conference and Exposition · doi:10.1109/apec42165.2021.9487195 · Cited by 34 · cited 4×
“A modular single-stage electrolytic capacitor-less 3-phase OBC which can work with 1-phase grids as well is proposed in [77].”
BackgroundMethodInfluentialInterleaved Isolated Single-Phase PFC Converter Module for Three-Phase EV Charger
Choi, S.-W., Oh, S.-T., Kim, M., Lee, I.-O., & Lee, J. (2020) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2020.2980878 · Cited by 33 · cited 3×
“However, its transformer-less design may raise safety concerns due to potential leakage current, though active suppression techniques can be employed [76].”
BackgroundAnalysis of Auxiliary Power Unit and Charging for an 800V Electric Vehicle
Aghabali, I., Bauman, J., & Emadi, A. (2019) · IEEE Transportation Electrification Conference and Expo · doi:10.1109/itec.2019.8790562 · Cited by 32 · cited 5×
“The novel single-stage topologies aim to reduce switch count as well as component count in general to improve the power density and reliability of the OBC [53], [71].”
BackgroundMethodInfluentialSelf-citationAbbasi, M., Kanathipan, K., & Lam, J. C. W. (2022) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2022.3163663 · Cited by 32 · cited 8×
“3 has been proposed in [35] for 800 V BEVs considering high voltage gain and high voltage across each switch in the charger circuit.”
BackgroundMethodResultInfluentialA Single-Stage High-Frequency-Link Modular Three-Phase $LLC$ AC–DC Converter
Mishima, T., & Mitsui, S. (2021) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2021.3111003 · Cited by 31 · cited 2×
“The LLC-based topology proposed in [74] does not use a DC link, improving the power density and making it cost effective.”
BackgroundA High-Efficiency High-Power-Density SiC-Based Portable Charger for Electric Vehicles
Ditze, S., Ehrlich, S., Weitz, N., Sauer, M., Aßmus, F., Sacher, A., Joffe, C., Sessler, C., & Meißner, P. (2022) · Electronics · doi:10.3390/electronics11121818 · Cited by 25 · cited 1×
“Reference [79] proposes a 3-phase topology where the Vienna converter is used for the PFC stage and an LLC resonant converter is used for the isolated DC-DC stage.”
MethodSingle-Phase Bridgeless Converter for On-Board EV Charger With Flexible Charging Capabilities
Dutta, S., Rathore, A. K., & Khadkikar, V. (2023) · IEEE Journal of Emerging and Selected Topics in Industrial Electronics · doi:10.1109/jestie.2023.3270107 · Cited by 25 · cited 1×
“Also, V2V charging can help combat range anxiety because it allows the sharing of energy from one BEV to another [93], [94], making the BEV into a portable power source.”
BackgroundSelf-citationAbbasi, M., & Lam, J. C. W. (2020) · Conference proceedings/Conference proceedings - IEEE Applied Power Electronics Conference and Exposition · doi:10.1109/apec39645.2020.9124294 · Cited by 24
Sarnago, H., Lucía, Ó., Pérez‐Jiménez, R., & Gaona, P. (2021) · Conference proceedings/Conference proceedings - IEEE Applied Power Electronics Conference and Exposition · doi:10.1109/apec42165.2021.9487272 · Cited by 17 · cited 7×
“Reference [61] proposes a low cost and modular onboard charger DC/DC topology incorporating differential power processing [60], [62], [63] for high efficiency and power density, as shown in Fig.”
BackgroundMethodInfluentialAn 800V End to End SiC Powertrain to Accommodate Extremely Fast Charging
Deb, N., & Singh, R. G. (2023) · Journal of Energy and Power Technology · doi:10.21926/jept.2301007 · Cited by 12 · cited 1×
“By doubling the battery nominal voltage to around 800 V, charging currents are halved, opening up opportunities for much higher charging levels [8].”
BackgroundA comparison of on-board chargers for electric vehicles with variable DC-link voltage
Bolte, S., Speerschneider, A., Fröhleke, N., et al. (2015) · IEEE International Conference on Smart Energy Grid Engineering (SEGE) · doi:10.1109/sege.2015.7324598 · Cited by 12 · cited 1×
“The PFC converter regulates the voltage at the DC-link which allows the LLC converter to operate at constant resonant frequency, resulting in high efficiency [70] due to soft switching.”
BackgroundTransformerless Onboard Charger for Electric Vehicles with 800 V Power System
Langmaack, N., Tareilus, G., Bremer, G., et al. (2019) · IEEE International Conference on Power Electronics and Drive Systems (PEDS) · doi:10.1109/peds44367.2019.8998923 · Cited by 12 · cited 2×
“Reference [78] proposed a transformer-less topology with bidirectional charging capabilities, however, it uses complicated vector control for its operation.”
BackgroundSousa, T. J. C., Machado, L., Pedrosa, D., et al. (2020) · IEEE International Conference on Compatibility, Power Electronics and Power Engineering · doi:10.1109/cpe-powereng48600.2020.9161697 · Cited by 12 · cited 1×
“SiC semiconductors have better gate oxide reliability, are easy to use, and are robust with excellent voltage blocking capabilities [87].”
BackgroundGaN and SiC Based 500kHz Resonant Bidirectional DC/DC Design for 800V OBCM Application
Jia, M., Sun, H., Cai, J., Zhang, H., Zhou, Z., & Chen, J. (2024) · 2024 IEEE Applied Power Electronics Conference and Exposition (APEC) · doi:10.1109/apec48139.2024.10509331 · Cited by 7 · cited 2×
“A bidirectional isolated DC-DC converter based on the resonant DAB topology is developed in [72] for 800 V onboard charging, and is shown in Fig.”
BackgroundMethodHigh Efficiency GaN-based Non-isolated Electric Vehicle On-board Charger with Active Filtering
Dong, A., Sadeghpour, D., & Bauman, J. (2022) · IEEE Transportation Electrification Conference and Expo · doi:10.1109/itec53557.2022.9813849 · Cited by 6 · cited 1×
“However, this is a non-isolated design, which may raise safety concerns due to leakage current [75].”
BackgroundSelf-citationOutlook for Electric Vehicles and Implications for the Oil Market
Latulippe, É., & Mo, K. (2021) · Staff Analytical Notes · doi:10.34989/san-2019-19 · Cited by 5
Converter Topology Comparison for a Two-Stage Level-2 Onboard Charger in 800-V EV Powertrains
Pradhan, R., Narimani, M., & Emadi, A. (2022) · Annual Conference of the IEEE Industrial Electronics Society (IECON) · doi:10.1109/iecon49645.2022.9968504 · Cited by 5 · cited 9×
“A 11.5 kW simulated model is built using SiC MOSFETs in [67], which achieves a highest average simulated efficiency of 96.12% for IPOP-DAB and 96.22% for IPOS-DAB.”
BackgroundMethodInfluentialSingle-Phase Bridgeless Cuk-Derived DC-DC Converter for Vehicle-to-Vehicle Charge Transfer
Dutta, S., Rathore, A. K., Khadkikar, V., & Zeineldin, H. H. (2021) · IEEE Transportation Electrification Conference (ITEC-India) · doi:10.1109/itec-india53713.2021.9932524 · Cited by 5 · cited 1×
“Also, V2V charging can help combat range anxiety because it allows the sharing of energy from one BEV to another [93], [94], making the BEV into a portable power source.”
BackgroundSelf-citationA new AC charging system with orderly charging for electric vehicles
Xiaoping, J. (2013) · International Conference on Power Electronics Systems and Applications · doi:10.1109/pesa.2013.6828230 · Cited by 3
A SiC Based High Efficiency 22kW Bi-directional EV On-Board Charger
Chen, W., Xie, H., Liu, Y., Hu, Z., & Shao, J. (2021) · Cited by 2
Research works printed but not linked: 37
- 2023, Global Electric Car Sales Rose 31% in 2023—Rho Motion | Reuters
- Voelcker, 2016, Porsches 800-Volt Fast Charging for Electric Cars: Why It Matters
- Reber, 2016, E-Power: New Possibilities With 800-Volt Charging
- 2024, Porsche Charging All-electric Porsche Models Quickly and Easily—Porsche USA
- 2024, Aston Martin to Display Rapide E At Fully Charged Live
- 2024, Hyundai IONIQ 5 Charging Time, Range, and Cost | EVBox
- 2023, Genesis G80 Electrified Luxury
- 2024, Audi E-Tron GT RS
- 2022, Kia EV6 U.S. Specs Compared: Battery, Range, Price And More
- 2020, High Power Charging; Fast Charging Just Got Faster
- Clark, 2009, Real-Time ’CO2 Intensity’ Site Makes the Case for Midnight Dishwashing
- 2024, North American Voltage Ranges
- Locke, 2023, Single Phase vs. Three Phase Power: North American Edition
- 2021, Single and 3-Phase Charging—The Difference
- 2023, Higher Voltage Packs
- Paulraj, 2021, Charging Basics 102: Electric Vehicle Charging Levels, Modes and Types Explained: North America Vs. Europe Charging Cables and Plug Types
- 2024, Design Guide
- 2019, Power Quality Requirements for Plug-In Electric Vehicle Chargers—Part 1: Requirements
- 2018, Electromagnetic Compatibility (EMC)—Part 3–2: Limits—Limits for Harmonic Current Emissions
- 2022, CREE SiC MOSFET Gen2 40mOhm Datasheet
- 2023, GaN Systems 800V 11kW OBC Reference Design—Key Insights
- 10.30420/565822004 · doi:10.30420/565822004
- 2024, On-board Charger
- 2024, Power Electronics
- 2016, Transformer Losses
- 2022, Putting Energy Efficient Transformr Procurement Into Practice: A Guide to Using Total Cost of Ownership When Purchasing Distribution Transformers
- 2023, GaN Systems Unveils Revolutionary New GaN-Based 800V On-Board Charger (OBC) Reference Design
- 2024, On-Board Chargers—Catalogue
- 2023, On-Board Charger—LG Magna E-Powertrain
- 2024, EV High Voltage On-Board Charger
- 2024, 11kW 3-in-1 On Board Charging System(High-Voltage) | Huawei Digital Power
- 2024, Transphorm GaN Power FET Portfolio
- 2024, The Many Benefits of V2G Charging
- 2023, What Is Bidirectional Charging?
- 10.1109/TIE.2021.3084181 · DOI · Paper page
- Gitlin, 2023, General Motors Will Add Bidirectional Charging To Its Ultium-based EVs
- 2023, Site Maintenance
Cited by
Kumar, M., Kumar, A., Soomro, A. M., Baloch, M. H., Chaudhary, S. T., & Shaikh, M. A. (2024) · World Electric Vehicle Journal · doi:10.3390/wevj15110523 · Cited by 16
GaN Electric Vehicle Systems—A Comparative Review
Ayomide, A. I., Bhattacharya, I., Ezugwu, E. O., & Dhason, M. V. A. (2025) · Energies · doi:10.3390/en18226020 · Cited by 13
Lee, P., Han, D., & Kim, J. (2025) · Journal of Power Electronics · doi:10.1007/s43236-025-01012-6 · Cited by 5
“In addition, battery systems for electric vehicles are evolving from 400 V systems to 800 V systems [5–7].”
Tubburee, O., Photong, C., Angkawisittpan, N., Ek-iam, K., & Sa-ngiamvibool, W. (2025) · Engineering Technology & Applied Science Research · doi:10.48084/etasr.12947 · Cited by 5
“Fast charging, especially using Direct Current (DC) systems, is important as it significantly reduces the charging time and improves the energy efficiency [2, 3], with the operating voltage increasing from 600 V to 800 V [4].”
Setlhaolo, D., & Bayoumi, E. H. E. (2025) · International Transactions on Electrical Energy Systems · doi:10.1155/etep/6696258 · Cited by 5
“As a result, the expansion of ultra-fast charging technology is supporting the role of higher voltage architectures, such as the 800 V systems present in modern EVs such as the Porsche Taycan and Hyundai Ioniq 5 [77, 78].”
Metadata
- Authors
- Dutta, S., & Bauman, J.
- Affiliations
- McMaster University (CA)
- Venue
- IEEE Access
- Published
- 2024
- Volume
- 12
- Pages
- 105850-105864
- ISSN
- 2169-3536 (ISSN-L)
- OpenAlex
- W4401070335
- Cited by
- 37
- References
- 60
- Citations by year
- 2026: 19 · 2025: 15 · 2024: 3
- FWCI
- 3.81
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Locations
- IEEE Access (publishedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Funders
- Natural Sciences and Engineering Research Council of Canada
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Advanced DC-DC Converters
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Electric Vehicles and Infrastructure
- Physical Sciences › Engineering › Automotive Engineering › Electric and Hybrid Vehicle Technologies
- Keywords
- battery electric vehicles, ultrafast charging, single-phase charging, residential charging, thermal management
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.