A General Energy Balance for Battery Systems
Open accessThe DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index; 2 of the 20 sources its claims cite were checked for support.
Abstract
A general energy balance for battery systems has been developed. This equation is useful for estimating cell thermal characteristics. Reliable predictions of cell temperature and heat‐generation rate are required for the design and thermal management of battery systems. The temperature of a cell changes as a result of electrochemical reactions, phase changes, mixing effects, and joule heating. The equation developed incorporates these effects in a complete and general manner. Simplifications and special cases are discussed. The results of applying the energy balance to a mathematical model of the cell discharged through two different reaction mechanisms are given as examples. The examples illustrate how the energy equation may be applied to a specific system to examine the relative contributions corresponding to the terms in the equation. The examples show that the processes involved in cell heat generation may be complex and that the application of a sufficiently general energy equation is advantageous.
Overview
CoChat Summary
TL;DR
The paper derives a general energy balance for battery systems that includes mixing, phase changes, and simultaneous electrochemical reactions with composition-dependent open-circuit potentials. It applies the equation to a modeled LiAl/LiCl-KCl/FeS cell discharged by two mechanisms and to a lead-acid estimate, showing that cell heat generation can be complex and that a sufficiently general energy equation is advantageous.
Key findings
- A general energy balance is developed that includes energy contributions from mixing, phase changes, and simultaneous electrochemical reactions with composition-dependent open-circuit potentials; prior treatments were restricted to single pure-phase reactants or a single reaction without mixing effects.
- For the LiAl/FeS model, adiabatic-reversible discharge gives the same temperature at 100% depth of discharge for both mechanisms because the overall reaction is the same; slope discontinuities occur at 50% and 12% utilization for mechanisms 1 and 2, respectively. In the realistic simulations, the second reaction begins at 30% and 11% utilization for mechanisms 1 and 2, respectively.
- The mixing term is negligible in the LiAl/FeS example; at 25% utilization, the temperature decline after current interruption is only about 0.2 K. For a lead-acid cell, the estimated temperature rise after full discharge is approximately 1.6 K, or 2.9 K if 1.25 mol of PbO2 is allowed for discharge.
- The sign of the mixing effect depends on the enthalpy curve: for lead-acid, the sulfuric acid-water enthalpy curve is concave upward, so a well-insulated cell heats after current interruption; for the high-temperature LiCl-KCl cell, the curve is concave downward, so the cell cools after interruption. Neglecting mixing overestimates lead-acid operating temperature and underestimates high-temperature cell operating temperature.
Methods
- The paper derives the energy balance from the first law of thermodynamics, assuming uniform battery temperature, and presents a final general equation including reaction, heat-capacity, phase-change, mixing, electrical-work, and heat-transfer terms.
- The equation is applied to an existing one-dimensional mathematical model of the LiAl/LiCl-KCl/FeS cell with a porous LiAl negative electrode, porous FeS positive electrode, electrolyte reservoir, and separator under galvanostatic discharge, using the two reaction mechanisms in Table I.
- Appendix A estimates the lead-acid temperature rise using an assumed uniform 5 molal sulfuric acid electrolyte, with one-third of the electrolyte in the cathode and anode spaces and one-third between the electrodes; the analysis compares adiabatic-reversible profiles with model simulations and examines the relative contributions of terms.
Limitations
- The paper states that the rigorous energy balance is difficult to apply without a detailed mathematical model because instantaneous composition profiles and current fractions are required; in practice, obtaining concentration profiles and predicting current partitioning among possible reactions is difficult.
- The paper states that the analysis does not include enthalpy changes from nonfaradaic reactions; self-discharge or corrosion must be divided into anodic and cathodic components and included as an additional term. The mixing term is also difficult because it involves integrations of concentration profiles.
- The paper states that actual FeS discharge is complicated and more like a mixture of the two proposed mechanisms plus simultaneously occurring chemical reactions; the examples are model simulations. The lead-acid estimate assumes artificial concentration jumps at interfaces, and diffusion would lower the estimate; nonuniform reaction distribution in porous electrodes would make the concentration distribution nonuniform. The breakdown is presented only up to 30% utilization because oscillatory behavior begins when the second reaction starts, to be treated in a subsequent publication.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
0 Valid · 5 Not valid · 12 Not checked · 75 Own results and interpretations
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“Basing the discharge on two Farādays (1 mol PbOg) and a transference number of 0.74 for hydrogen ion, we may calculate that the concentration in the cathode space and anode space drops to 1.04 and 2.79 molal, respectively (14).”
What the sources say
- Could not verifycites [14] 14. Hans Bode, "Lead-Acid Batteries," R. J. Brodd and K. V. Kordesch, Translators, Wiley-Interscience, New York (1977). sourceExperimental — accuracy not yet measured
The available text in the book-review passage (section labeled “Notice to Members April 1 is Cut-Off Date”; page not provided) describes the book’s theoretical treatment of lead-acid batteries but does not give this calculation. Searches for the 0.74 hydrogen-ion transference number, two Faradays, and the 1.04 and 2.79 molal concentrations found no passage addressing the claimed values. (LLM, conf=0.76)
hedgedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on 5 assumptions not shown here.
- Could not verify
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“The temperature rise, after full discharge, is approximately 1.6 K.”
- Also stated in: § Estimate of the Temperature Rise in a Lead-Acid Cell Following Current Interruption · p. 8 · hedged
“Using the data available in Ref. (14) (for 298 K), we calculate the temperature rise to be about 1.6 K”
What the sources say
- Could not verifycites [14] 14. Hans Bode, "Lead-Acid Batteries," R. J. Brodd and K. V. Kordesch, Translators, Wiley-Interscience, New York (1977). sourceExperimental — accuracy not yet measured
The available passages from the book review (page not provided) describe the book’s coverage of lead-acid battery thermodynamics but give no temperature rise after full discharge. Searches for “1.6 K” and the discharge-temperature claim found no supporting passage in our copy. (LLM, conf=0.75)
hedged- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on 5 assumptions not shown here.
- Also stated in: § Estimate of the Temperature Rise in a Lead-Acid Cell Following Current Interruption · p. 8 · hedged
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Although the mixing term offers a negligible contribution to the energy balance, it is interesting to investigate the processes that determine its behavior.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The profile for the X-phase mechanism in Fig. 1 follows the adiabatic-reversible profile up to about 5% utilization because the heat-loss contribution tends to cancel the polarization heat.”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“A general energy balance for battery systems has been developed.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on 3 assumptions not shown here.
39 more claims
Create a free account to see all 92 claims and every source verdict.
- It may state two separate claims as one. 20
- Probably not a substantial claim. 33
- The quote only partly states this claim. 1
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Conclusions · p. 8
“Equation [23], written for a single cell reaction, is the energy equation most commonly used in battery applications.”
§ Discussion of Terms · p. 5
“Furthermore, Eq. [24] is the form of the energy balance that is most commonly encountered in the literature.”
Citations
Cites
The publisher hasn’t deposited this paper’s reference list.
Research works printed but not linked: 12
- [1]1. J. M. Sherfey and A. Brenner, This Journal, 105, 665 (1958).
- [3]3. H. F. Gibbard, This Journal, 125, 353 (1978).
- [2]2. S. Gross, Energy Convers., 9, 55 (1969).
- [4]4. I. A. Dibrov and V. A. Bykov, Sov. Electrochem., 13, 298 (1977).
- [6]6. L. D. Hansen and R. M. Hart, This Journal, 125, 842 (1978).
- [5]5. I. A. Dibrov and V. A. Bykov, J. Appl. Chem., 49, 2025 (1977).
- [7]7. F. B. Tudron, ibid., 128, 516 (1981).
- [9]9. W. H. Tiedemann and J. Newman, in "Battery Design and Optimization," S. Gross, Editor, pp. 23-38, The Electrochemical Society Softbound Proceedings Series, Princeton, NJ (1979).
- [8]8. D. M. Chen and H. F. Gibbard, ibid., 130, 1975 (1983).
- [10]10. Richard Pollard and John Newman, This Journal, 128, 491 (1981).
- [11]11. Richard Pollard and John Newman, ibid., 128, 502 (1981).
- [13]13. Z. Tomczuk, S. K. Preto, and M. F. Roche, This Journal, 128, 760 (1981).
Cited by
Items 1,401–1,500 of 2,542
Murashko, K., Mityakov, A. V., Mityakov, V. Y., Sapozhnikov, S. Z., Pyrhonen, J. J., & Jokiniemi, J. K. (2019) · Journal of The Electrochemical Society · doi:10.1149/2.0711913jes · Cited by 9
Stochastic Model Predictive Controller for Battery Thermal Management of Electric Vehicles
Park, S., & Ahn, C. (2019) · IEEE Vehicle Power and Propulsion Conference (VPPC) · doi:10.1109/vppc46532.2019.8952340 · Cited by 9
Battery thermal management of electric vehicles
Shijina, S. S., Mathew, J., & Sajith, V. (2024) · Elsevier eBooks · doi:10.1016/b978-0-443-19025-4.00001-4 · Cited by 9
Study on Thermal Effect of Aluminum-Air Battery
Cai, Y., Tong, Y., Liu, Y., et al. (2023) · Nanomaterials · doi:10.3390/nano13040646 · Cited by 8
“In addition, the heat generation equation of the battery system was also proposed according to the law of energy conservation, which has been used to predict battery discharge performance at different operating temperatures [21].”
MethodA Novel Experimental Testing Setup and Calibration Procedures for Cylindrical Cell Thermal Models
Gravante, E., Idrissi, F. E., Ramesh, P., & D’Arpino, M. (2023) · IEEE Access · doi:10.1109/access.2023.3285814 · Cited by 8
“thermodynamic energy balance, has been proposed in [27]:”
BackgroundFu, P., Fang, L., Jiao, S., et al. (2023) · Energies · doi:10.3390/en16227673 · Cited by 8
“In order to simplify the calculation, according to D. Bernardi’s battery heat generation theory [21], the heat generated by the battery is mainly divided into four parts: the chemical reaction heat Q r , the polarization heat Q p , Joule heat Q j and the side reaction heat Q s .”
MethodA Combined Data-Driven and Model-Based Algorithm for Accurate Battery Thermal Runaway Warning
Chen, Q., He, Y., Fang, N., et al. (2024) · Sensors · doi:10.3390/s24154964 · Cited by 8
“To this end, we utilize the Bernardi equation to fulfill this task and develop a conversion model between battery electrical energy and thermal energy [16].”
MethodNovel AgO-based nanofluid for efficient thermal management of 21700-type lithium-ion battery
Sarchami, A., Tousi, M., Darab, M., Kiani, M., Najafi, M., & Houshfar, E. (2024) · Sustainable Energy Technologies and Assessments · doi:10.1016/j.seta.2024.103934 · Cited by 12
He, Z., Chen, Y., & He, D. (2024) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2024.124418 · Cited by 11
Xin, K., & Lee, G. (2024) · World Electric Vehicle Journal · doi:10.3390/wevj15090423 · Cited by 8
Williams, N. P., Zelent, B., Trimble, D., et al. (2024) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2024.124597 · Cited by 8
Liu, Y. C., Qi, C., & Guo, C. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.116393 · Cited by 8
Kim, D., Kw, J., Um, K., & Hong, J. (2025) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2025.127435 · Cited by 8
Lee, Y.-B., Kim, W., & Han, J. (2025) · Renewable Energy · doi:10.1016/j.renene.2025.123926 · Cited by 8
Yuan, C., Zhang, W., Zhang, L., Zhang, C., & Hu, J. (2025) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2025.127646 · Cited by 9
Wang, J., Zhang, Q., Zhang, Y., Shi, J., & Zhou, D. (2025) · Thermochimica Acta · doi:10.1016/j.tca.2025.180085 · Cited by 9
Du, K., Chen, G., Zhang, Y., Li, S., Shi, B., Zhang, T., Liu, J., Chen, F., Xie, S., & Guo, Z. (2025) · Energy storage materials · doi:10.1016/j.ensm.2025.104597 · Cited by 49
Gao, Q., Zhang, Z., & Liu, D. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.119121 · Cited by 8
Research progress on hybrid battery thermal management systems based on phase change material
Li, W., Nie, L., Zhang, X., & Zhao, J. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.119179 · Cited by 9
Rastogi, S., Sohaliya, P., & Bakli, C. (2026) · Journal of Power Sources · doi:10.1016/j.jpowsour.2026.239362 · Cited by 8
Jiang, C., Wang, J., Yang, L., et al. (2026) · International Journal of Thermal Sciences · doi:10.1016/j.ijthermalsci.2026.110903 · Cited by 8
A cost and time effective novel methodology to determine specific heat capacity of lithium-ion cells
Balkur, S., Chowdhury, N. R., Groot, J., & Thiringer, T. (2021) · Journal of Power Sources · doi:10.1016/j.jpowsour.2021.229981 · Cited by 8
Kim, M., Ham, J., Shin, D., & Cho, H. (2022) · Batteries · doi:10.3390/batteries8100195 · Cited by 7
“The equation of heat generated in a battery (Qgen) is as follows [40,41].”
BackgroundLiu, F., Bao, R., Cheng, X., & Wu, Q. (2023) · Energy Science & Engineering · doi:10.1002/ese3.1418 · Cited by 8
Zhuang, X., Zhang, A., Wang, B., & Wang, J. (2023) · Journal of Thermal Stresses · doi:10.1080/01495739.2023.2270001 · Cited by 7
“In this study, the heat generation equation per unit volume developed by Bernardi et al. [35] is adopted: where I , V , U oc and U are the current, total volume of the battery, open-circuit potential and working voltage, respectively.”
MethodDetailed Thermal Characterization on a 48V Lithium-Ion Battery Pack during Charge-Discharge Cycles
Carlucci, A. P., Darvish, H., & Laforgia, D. (2023) · SAE technical papers on CD-ROM/SAE technical paper series · doi:10.4271/2023-32-0135 · Cited by 8
“(1) is generated during either the reversible ( 𝑄 𝑟𝑒𝑣 ) or the irreversible ( 𝑄 𝑖𝑟𝑟 ) processes taking place in Li-ion batteries [36,38-40].”
Lu, Y., Han, X., Li, Y., Li, X., & Ouyang, M. (2024) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2024.3427049 · Cited by 10
“Bernardi’s theory [37] is adopted and the model is formulated as: where Q gen is the heat generation and Q loss is the convective heat exchange with the environment. h represents the heat transfer coefficient and A is the surface area of the cell.”
MethodXu, Y., Zhang, Y., Zeng, M., Huang, X., & Wang, Z. (2024) · Electrochemistry Communications · doi:10.1016/j.elecom.2024.107776 · Cited by 10
Optimal charging of a Li-ion cell: A hybrid Model Predictive Control approach
Torchio, M., Magni, L., Braatz, R. D., et al. (2016) · Proceedings of the IEEE Conference on Decision & Control, including the Symposium on Adaptive Processes · doi:10.1109/cdc.2016.7798883 · Cited by 8
“When designing an ABMS, an accurate model of the thermal behaviour is important for allowing a reduction of safety risks and possible damage, and, in extreme cases, avoidance of thermal runaways [14], [15].”
MethodLi, X., & Rui, X. (2018) · IFAC-PapersOnLine · doi:10.1016/j.ifacol.2018.10.046 · Cited by 8
Kleiner, J., Komsiyska, L., Elger, G., & Endisch, C. (2019) · International Workshop on Thermal Investigations of ICs and Systems · doi:10.1109/therminic.2019.8923604 · Cited by 9
“Subsequently, equation (4) is used for calculating the time-dependent heat generation in a lithium-ion system [8]:”
BackgroundA Novel Loop Heat Pipe Based Cooling System for Battery Packs in Electric Vehicles
Bernagozzi, M., Georgoulas, A. N., Miché, N., et al. (2020) · IEEE Transportation Electrification Conference & Expo (ITEC) · doi:10.1109/itec48692.2020.9161607 · Cited by 8
Murashko, K., Li, D., Danilov, D. L., Notten, P. H. L., Pyrhonen, J. J., & Jokiniemi, J. K. (2021) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/abd832 · Cited by 8
Li, J., Lei, F., Zhu, W., Qiu, Z., & Wu, H. (2021) · Structural and Multidisciplinary Optimization · doi:10.1007/s00158-021-03042-7 · Cited by 10
“1 3 heat generation can be calculated based on Bernadi equation (Bernardi et al. 1985), as shown in Eq.”
MethodAvoiding Thermal Issues During Fast Charging Starting with Proper Cell Selection Criteria
Gonzalez-Aguirre, E., Gastelurrutia, J., Patil, M. S., & del Portillo, L. A. (2021) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/ac3348 · Cited by 8
Huynh, V.-T., Chang, K., & Lee, S.-W. (2021) · Energies · doi:10.3390/en14248386 · Cited by 8
Naik, I. C., & Nandgaonkar, M. R. (2021) · Energy Technology · doi:10.1002/ente.202100774 · Cited by 8
Module-Level Modelling Approach for a Cloudbased Digital Twin Platform for Li-Ion Batteries
Lizaso-Eguileta, O., Martinez-Laserna, E., Rivas, M., Miguel, E., Iraola, U., & Cantero, I. (2021) · IEEE Vehicle Power and Propulsion Conference (VPPC) · doi:10.1109/vppc53923.2021.9699271 · Cited by 12
Thermal Modeling and Prediction of The Lithium-ion Battery Based on Driving Behavior
Wang, T., Liu, X., Qin, D., & Duan, Y. (2022) · Energies · doi:10.3390/en15239088 · Cited by 15
Kim, D., Abdallahh, S., Bosi, G., & Hales, A. (2023) · World Electric Vehicle Journal · doi:10.3390/wevj14010015 · Cited by 12
In-situ measurement of the heat generation of LiFePO4 and Li(Ni1/3Co1/3Mn1/3)O2 batteries
Liu, S., Lu, S., Fu, Y., et al. (2023) · Journal of Power Sources · doi:10.1016/j.jpowsour.2023.233187 · Cited by 8
Tang, Z., Ji, Y., Sun, R., et al. (2023) · Energy Technology · doi:10.1002/ente.202300631 · Cited by 8
Thermal Characterization of a Li-ion Battery Module Cooled through Aluminum Heat-Sink Plates
Teng, H., Ma, Y., Yeow, K. F., et al. (2011) · SAE International Journal of Passenger Cars - Mechanical Systems · doi:10.4271/2011-01-2248 · Cited by 8
Tang, Y., Ming, J., Cheng, Y., et al. (2013) · Acta Physica Sinica · doi:10.7498/aps.62.158201 · Cited by 8
Modular energy efficient and solid-state Battery Thermal Management System
Alaoui, C. (2017) · International Conference on Wireless Technologies, Embedded and Intelligent Systems (WITS) · doi:10.1109/wits.2017.7934608 · Cited by 8
Investigations on the reversible heat generation rates of blended Li-insertion electrodes
Liebmann, T., Heubner, C., Schneider, M., et al. (2018) · Journal of Solid State Electrochemistry · doi:10.1007/s10008-018-4127-4 · Cited by 8
Design and test of a battery pack simulator
van Sterkenburg, S., Fleuren, T., Veenhuizen, B., et al. (2013) · doi:10.1109/evs.2013.6914804 · Cited by 8
“The thermal model of the battery pack is based on the thermal heat conductance between the cells mutually and from the cells to the environment [2], [3], [4].”
BackgroundAcharya, S., Khan, R., & Agarwal, P. K. (2023) · ASME Journal of Heat and Mass Transfer · doi:10.1115/1.4062759 · Cited by 7
An Input-to-State Safety Approach Toward Thermal Fault-Tolerant Battery Cells
Vyas, S. D., Roy, T., & Dey, S. (2024) · IEEE Transactions on Control Systems Technology · doi:10.1109/tcst.2023.3345130 · Cited by 7
“The modeling equations are given by Then, we adopt the following heat generation model proposed in [31]: where ( d OCV / dT ) is the entropic heat coefficient.”
MethodFang, Y., Wang, Z., Wang, N., et al. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2024.113061 · Cited by 7
A new bottom and radial coupled heat dissipation model for battery thermal management system
Zhang, Y., Wang, Z., Zou, S., et al. (2024) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2024.124794 · Cited by 7
Pan, X., Xu, C., Sun, X., Shi, J., Zhou, Z., & Liu, Y. (2024) · PLoS ONE · doi:10.1371/journal.pone.0313594 · Cited by 7
Wang, Y., Zhang, Y., Zhang, M., Wang, J., & Ma, T. (2025) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2025.125479 · Cited by 8
Liu, Z., Zhou, Y., Zhang, Y., Li, J., & Liu, S. (2025) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2025.125647 · Cited by 6
Jiang, W., Lyu, P., Liu, X., et al. (2025) · International Communications in Heat and Mass Transfer · doi:10.1016/j.icheatmasstransfer.2025.108656 · Cited by 7
Gao, T., Wang, J., Sha, H., et al. (2025) · Energies · doi:10.3390/en18041011 · Cited by 7
Thermally conductive phase change electrodes for in situ thermal management of lithium-ion batteries
Wang, L., Li, S.-Z., Liu, W., Jiang, N., Song, Y., Bai, L., Wang, Y., Yin, B., Yang, J., & Yang, W. M. (2025) · Journal of Materials Chemistry A · doi:10.1039/d4ta08893j · Cited by 9
Yu, M., Meng, S., Wei, R., et al. (2025) · Measurement · doi:10.1016/j.measurement.2025.117548 · Cited by 7
Wang, J., Chen, B., Fen, L., et al. (2025) · International Communications in Heat and Mass Transfer · doi:10.1016/j.icheatmasstransfer.2025.109306 · Cited by 7
Saudi, M. K., Hassan, H., Khalil, A. S. G., & Emam, M. (2025) · International Journal of Thermal Sciences · doi:10.1016/j.ijthermalsci.2025.110193 · Cited by 8
Study on the flexibility of forced convection immersion cooling lithium-ion batteries
He, K., Liu, Q., He, H., et al. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.117910 · Cited by 7
Shehabaz, S. M., Gugulothu, S. K., Muthyala, R., Vishnu, P., Buliraju, P., & Sailaja, G. (2025) · Journal of Thermal Science and Engineering Applications · doi:10.1115/1.4069841 · Cited by 10
Niu, Z.-H., Pang, K., Pang, B.-B., et al. (2025) · Scientific Reports · doi:10.1038/s41598-025-19098-0 · Cited by 7
Reiter, A., Schütte, M., Rosenmüller, C., Stroebl, F., Lehner, S., Sauer, D. U., & Bohlen, O. S. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.118897 · Cited by 12
Du, X., Wang, Z., Bao, R., et al. (2025) · International Journal of Heat and Fluid Flow · doi:10.1016/j.ijheatfluidflow.2025.110117 · Cited by 7
Jia, Y., Liu, S., Zhao, D., Luo, Y., & Wang, J. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.119224 · Cited by 7
Zhao, L., Wang, J., Zheng, M., et al. (2025) · International Journal of Heat and Fluid Flow · doi:10.1016/j.ijheatfluidflow.2025.110181 · Cited by 7
Xiao, Y., Liu, S., Hu, X., Gao, Z., Rong, C., Li, W., Song, Y., & Zhang, H. (2026) · Journal of Energy Storage · doi:10.1016/j.est.2026.120775 · Cited by 9
Zhang, D., Zhang, J., & Zheng, Y. (2026) · Journal of Energy Storage · doi:10.1016/j.est.2026.121038 · Cited by 8
Wang, X., Yin, R., & Peng, Q. (2026) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2026.130611 · Cited by 9
Yan, W.-M., Chien, B.-S., Li, C.-H., et al. (2026) · International Journal of Thermal Sciences · doi:10.1016/j.ijthermalsci.2026.110870 · Cited by 7
Multi-Scenario Digital Modeling and Simulation of Lithium-Ion Batteries
Li, W., Bao, Z., Wang, D., Wang, Y., Yu, Y., Li, H., Du, Q., Jin, Z., & Jiao, K. (2026) · Electrochemical Energy Reviews · doi:10.1007/s41918-026-00284-1 · Cited by 12
Equalization of battery cycle life through flexible distribution of energy and storage resources
Khasawneh, H. J., & Illindala, M. S. (2014) · IEEE/IAS Industrial and Commercial Power Systems Technical Conference · doi:10.1109/icps.2014.6839172 · Cited by 7
Karatas, O. B., & SÖKMEN, K. F. (2022) · Journal of Energy Storage · doi:10.1016/j.est.2022.105705 · Cited by 8
Nahidi, S., Gavzan, I. J., Saedodin, S., et al. (2022) · Journal of the Brazilian Society of Mechanical Sciences and Engineering · doi:10.1007/s40430-022-03923-y · Cited by 7
“Since the measurement of void fraction (ε) of gas bubbles in electrolyte and the Rbubble directly in the experimental studies is very challenging and has many errors, in this study, like other experimental studies [16, 17, 23], the relation (1) is used to determine (ε) of gas bubbles in electrolytes.”
MethodGu, J., Xu, R., Chen, B., & Zhou, J. (2023) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/accaac · Cited by 7
Jeon, H., Hong, S., Yun, J., & Han, J. (2023) · Energies · doi:10.3390/en16237860 · Cited by 11
Bai, J., Rui, W., & Chen, H. (2024) · Journal of Energy Engineering · doi:10.1061/jleed9.eyeng-5237 · Cited by 7
Frank, A., Durdel, A., Scheller, M., Sturm, J., & Jossen, A. (2024) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/ad5d1d · Cited by 7
Tahirağaoğlu, B., Sevilgen, G., & Hamut, H. S. (2024) · Case Studies in Thermal Engineering · doi:10.1016/j.csite.2024.105169 · Cited by 7
Bai, X., Jin, H., Duan, C., et al. (2024) · Thermal Science and Engineering Progress · doi:10.1016/j.tsep.2024.102920 · Cited by 7
Park, S., Lee, H., Park, C., & Kim, C. (2024) · Heliyon · doi:10.1016/j.heliyon.2024.e39220 · Cited by 8
Amuta, O., Yao, J., Droese, D., & Kowal, J. (2025) · Batteries · doi:10.3390/batteries11060208 · Cited by 7
“In addition, the chemical composition of the anode and cathode affects the rate of reversible heat generated in the LIB, which varies with the state of charge (SOC) [22,26–28].”
Modeling of Lithium Ion Batteries Employing Grand Canonical Monte Carlo and Multiscale Simulation
Kar, P., & Harinipriya, S. (2014) · Journal of The Electrochemical Society · doi:10.1149/2.021405jes · Cited by 7
Tian, N., & Fang, H. (2017) · Proceedings of the ... American Control Conference/Proceedings of the American Control Conference · doi:10.23919/acc.2017.7963068 · Cited by 7
Comprehensive determination of heat generation and thermal modelling of a hybrid capacitor
Miller, M., Baltes, N. T. M., Rabenecker, P. M., Hagen, M., & Tübke, J. (2019) · Journal of Power Sources · doi:10.1016/j.jpowsour.2019.226752 · Cited by 7
Simulation of thermal characteristics of lithium batteries for electric vehicles
Zhang, L. W., & Yu, Y. (2019) · IOP Conference Series Materials Science and Engineering · doi:10.1088/1757-899x/657/1/012036 · Cited by 9
“D Bernard’s heat generation model is commonly used to calculate the heat generation rate of batteries [7], expressed as:”
MethodJung, T.-J., Lee, H., Park, S. H., et al. (2022) · Journal of Power Sources · doi:10.1016/j.jpowsour.2022.231240 · Cited by 7
Ajour, M. N., Daqrouq, K. O., & Karimipour, A. (2022) · Journal of Energy Storage · doi:10.1016/j.est.2022.104383 · Cited by 7
RetractedAkkurt, N. (2022) · Journal of Power Sources · doi:10.1016/j.jpowsour.2022.231606 · Cited by 7
Thermo-Mechano-Electrochemical Analysis in Cylindrical Electrode Particles of Lithium-Ion Battery
Li, J., Liu, Y., & Wang, B. (2022) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/ac7979 · Cited by 7
Kumar, M., Sengupta, A., Gupta, K., Chakraborty, J., & Das, P. K. (2022) · Journal of Materials Science · doi:10.1007/s10853-022-07624-8 · Cited by 9
Thermal Analysis of Lithium Ion Battery Pack with Different Cooling Media
Pushkar, K., Napa, N., Madichetty, S., et al. (2022) · SAE technical papers on CD-ROM/SAE technical paper series · doi:10.4271/2022-28-0043 · Cited by 7
Wang, J., Ruan, L., & Li, R. (2022) · Energies · doi:10.3390/en15217897 · Cited by 8
Yan, H., Wang, Y., Wang, H., Li, Y., Lu, L., Du, J., Feng, X., Zhang, X., Li, D., & Feng, S. (2023) · Numerical Heat Transfer Part A Applications · doi:10.1080/10407782.2023.2178987 · Cited by 8
“[38] proposed a heat production rate model, which is the most commonly used computational model for estimating the heat production of cells.”
BackgroundLi, Z., Jiao, X., Zha, M., Yang, C., & Yang, L. (2023) · Applied Sciences · doi:10.3390/app13053032 · Cited by 9
“Therefore, the total heat generated by the battery Q is composed of joule heat and reaction heat, which can be expressed as [28]”
BackgroundHuang, Z., Wang, H., Yang, T., Liu, S., Li, H., Chen, J., & Wu, S. (2023) · Journal of Energy Storage · doi:10.1016/j.est.2023.107379 · Cited by 6
Comparative analysis of cooling effect of battery module cooling plate structures
Fang, H., Xu, J., Lu, Y., et al. (2023) · Thermal Science · doi:10.2298/tsci230520166f · Cited by 7
“The fluid state is determined by the Reynolds[18]number, ρ is Fluid density; V is Fluid velocity; L is Characteristic length (such as the diameter of a circular pipe, length of a flat plate, etc.”
BackgroundInfluentialLiu, L., Dong, S., Nan, B., & Lu, K. (2023) · IET Renewable Power Generation · doi:10.1049/rpg2.12823 · Cited by 7
Xing, S., Khudyshkina, A. D., Rauska, U., Butzelaar, A. J., Voll, D., Théato, P., Tübke, J., & Jeschull, F. (2024) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/ad3b72 · Cited by 7
Metadata
- Authors
- Bernardi, D., Pawlikowski, E., & Newman, J.
- Affiliations
- University of California, Berkeley (US)
- ORCID
- Newman, J.
- Venue
- Journal of The Electrochemical Society
- Publisher
- The Electrochemical Society
- Published
- 1985-01-01
- Volume
- 132
- Issue
- 1
- Pages
- 5-12
- ISSN
- 0013-4651 (ISSN-L)
- 1945-7111
- OpenAlex
- W2023385933
- Cited by
- 2,548
- References
- 0
- Citations by year
- 2026: 383 · 2025: 387 · 2024: 339 · 2023: 265 · 2022: 238 · 2021: 167 · 2020: 147 · 2019: 106 · 2018: 74 · 2017: 89 · 2016: 42 · 2015: 53 · 2014: 75 · 2013: 51 · 2012: 31
- FWCI
- 0.00
- Type
- journal article
- Language
- en
- Open access
- bronze
- doi.org
- Licence
- iopscience.iop.org/page/copyright (vor, 12758 d)
- iopscience.iop.org/info/page/text-and-data-mining (tdm, 12758 d)
- Locations
- Journal of The Electrochemical Society (publishedVersion)
- Topics
- Physical Sciences › Engineering › Automotive Engineering › Battery Modeling and Management
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Advancements in Battery Materials
- Physical Sciences › Chemistry › Electrochemistry › Molten salt chemistry and electrochemical processes
- Keywords
- heat generation rate, Joule heating, phase transitions, mixing effects, electrochemical reactions, battery thermal management, battery modeling
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.