Modeling of Galvanostatic Charge and Discharge of the Lithium/Polymer/Insertion Cell
Open accessThe DOI matches its Crossref record; 13 of the 13 references it cites were found in a registry or an index.
Abstract
The galvanostatic charge and discharge of a lithium anode/solid polymer separator/insertion cathode cell is modeled using concentrated solution theory. The model is general enough to include a wide range of polymeric separator materials, lithium salts, and composite insertion cathodes. Insertion of lithium into the active cathode material is simulated using superposition, thus greatly simplifying the numerical calculations. Variable physical properties are permitted in the model. The results of a simulation of the charge/discharge behavior of the system are presented. Criteria are established to assess the importance of diffusion in the solid matrix and transport in the electrolyte. Consideration is also given to various procedures for optimization of the utilization of active cathode material.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“According to their outcomes, KF output is superior to RLS [91].”
In the citing paper
“Electrochemical models are somewhat more accurate than the classical acoustic ones as being based on the description of the battery's inner chemical processes such as lithium ions diffusion of within the electrodes and the electrolyte [31].”
From Review Paper for SOC Estimation Techniques: Challenges and Future Areas for Improvement (2024) · cites this paper as [31]
Citations
Cites
(1996) · Journal of Power Sources · doi:10.1016/s0378-7753(97)81054-3 · Cited by 463
Experimental Determination of the Transport Number of Water in Nafion 117 Membrane
Fuller, T. F., & Newman, J. (1992) · Journal of The Electrochemical Society · doi:10.1149/1.2069407 · Cited by 278
Self-citationAssessment of Polymer‐Electrolyte Batteries for EV and Ambient Temperature Applications
Gauthier, M., Fauteux, D., Vassort, G., Bélanger, A., Duval, M., Ricoux, P., Chabagno, J. M., Muller, D. A., Rigaud, P., Armand, M. B., et al. (1985) · Journal of The Electrochemical Society · doi:10.1149/1.2114112 · Cited by 156
Formation of a passivating film at the lithium-PEO-LiCF3SO3 interface
Fauteux, D. (1985) · Solid State Ionics · doi:10.1016/0167-2738(85)90061-x · Cited by 134
The fabrication and performance of all solid state polymer-based rechargeable lithium cells
Hooper, A. J., & North, J. M. (1983) · Solid State Ionics · doi:10.1016/0167-2738(83)90146-7 · Cited by 124
Laminar Boundary Layer Flows with Surface Reactions
Acrivos, A., & Chambré, P. L. (1957) · Industrial & Engineering Chemistry · doi:10.1021/ie50570a037 · Cited by 100
Status of rechargeable positive electrodes for ambient temperature lithium batteries
Abraham, K. M. (1981) · Journal of Power Sources · doi:10.1016/0378-7753(81)80058-4 · Cited by 88
A Polymeric Electrolyte Rechargeable Lithium Battery
Bonino, F., Ottaviani, M., Scrosati, B., et al. (1988) · Journal of The Electrochemical Society · doi:10.1149/1.2095538 · Cited by 72
Lithium Electrode/PEO‐Based Polymer Electrolyte Interface Behavior Between 60° and 120°C
Fauteux, D. (1988) · Journal of The Electrochemical Society · doi:10.1149/1.2096244 · Cited by 64
Performance of polymer electrolyte cells at +25 to +100°C
Munshi, M. (1988) · Solid State Ionics · doi:10.1016/0167-2738(88)90244-5 · Cited by 62
Cited by
Items 801–900 of 1,016
Mai, W., Yang, M. S., & Soghrati, S. (2018) · Electrochimica Acta · doi:10.1016/j.electacta.2018.10.072 · Cited by 67
Modeling framework for multiphysics-multiscale behavior of Si–C composite anode
Gao, X. Y., Lu, W., & Xu, J. (2019) · Journal of Power Sources · doi:10.1016/j.jpowsour.2019.227501 · Cited by 67
Zeng, G., Bai, Z., Huang, P., & Wang, Q. (2020) · International Journal of Energy Research · doi:10.1002/er.5125 · Cited by 69
Jiang, G., Ling, Z., Hu, Q., Liu, Z., & Huang, J. (2020) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2020.115080 · Cited by 70
Geng, Z., Chien, Y., Lacey, M. J., Thiringer, T., & Brandell, D. (2021) · Electrochimica Acta · doi:10.1016/j.electacta.2021.139727 · Cited by 76
A Single Particle model with electrolyte and side reactions for degradation of lithium-ion batteries
Planella, F. B., & Widanage, W. D. (2022) · Applied Mathematical Modelling · doi:10.1016/j.apm.2022.12.009 · Cited by 75
“The most popular ones are the DoyleFuller-Newman model (DFN) introduced in [6, 7] and Single Particle Models (SPM), which are simpler.”
MethodBattery state-of-health diagnostics during fast cycling using physics-informed deep-learning
Weddle, P. J., Kim, S., Chen, B., Yi, Z., Gasper, P. J., Colclasure, A. M., Smith, K. A., Gering, K. L., Tanim, T. R., & Dufek, E. J. (2023) · Journal of Power Sources · doi:10.1016/j.jpowsour.2023.233582 · Cited by 72
Hosseininasab, S., Momtaheni, N., Pischinger, S., Günther, M., & Bauer, L. (2023) · Journal of Energy Storage · doi:10.1016/j.est.2023.109011 · Cited by 69
Thermoelectrochemical simulations of performance and abuse in 50-Ah automotive cells
Kim, S. U., Albertus, P. S., Cook, D. J., Monroe, C. W., & Christensen, J. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2014.06.080 · Cited by 73
A Phenomenological Degradation Model for Cyclic Aging of Lithium Ion Cell Materials
Narayanrao, R., Joglekar, M. M., & Inguva, S. (2012) · Journal of The Electrochemical Society · doi:10.1149/2.013302jes · Cited by 66
Concentration measurements in lithium/polymer–electrolyte/lithium cells during cycling
Brissot, C., Rosso, M., Chazalviel, J. N., & Lascaud, S. (2001) · Journal of Power Sources · doi:10.1016/s0378-7753(00)00589-9 · Cited by 66
Zhang, Q., & White, R. E. (2007) · Journal of Power Sources · doi:10.1016/j.jpowsour.2006.12.056 · Cited by 67
Nie, Z., McCormack, P. M., Bilheux, H., Bilheux, J.-C., Robinson, J. P., Nanda, J., & Koenig, G. M. (2019) · Journal of Power Sources · doi:10.1016/j.jpowsour.2019.02.075 · Cited by 69
Wang, B.-C., Li, H., & Yang, H.-D. (2019) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2019.2914637 · Cited by 68
“The lumped thermal model is also integrated with the pseudo-two-dimensional (P2D) model [9], [10].”
MethodLi, C., Cui, N., Cui, Z., Wang, C., & Zhang, C. (2022) · Journal of Power Sources · doi:10.1016/j.jpowsour.2022.230993 · Cited by 65
Roy, H., Roy, B. N., Hasanuzzaman, M., Islam, M. S., Abdel-Khalik, A. S., Hamad, M. S., & Ahmed, S. (2022) · Sustainability · doi:10.3390/su142416684 · Cited by 93
“The operation of an LIB is in agreement with the porous electrode theory and electrochemical reaction thermodynamics, and the scientist Newman advanced the governing equations [96].”
BackgroundResultDuan, X., Li, B., Li, J., Gao, X. Y., Wang, L., & Xu, J. (2023) · Advanced Energy Materials · doi:10.1002/aenm.202203767 · Cited by 65
Analysis of the Lithium-Ion Insertion Silicon Composite Electrode/Separator/Lithium Foil Cell
Chandrasekaran, R., & Fuller, T. F. (2011) · Journal of The Electrochemical Society · doi:10.1149/1.3589301 · Cited by 66
Self-citationWu, L., Xiao, X., Wen, Y., & Zhang, J. (2016) · Journal of Power Sources · doi:10.1016/j.jpowsour.2016.10.052 · Cited by 69
Simulating Process-Product Interdependencies in Battery Production Systems
Thomitzek, M., Schmidt, O., Röder, F., Krewer, U., Herrmann, C. A., & Thiede, S. (2018) · Procedia CIRP · doi:10.1016/j.procir.2018.03.056 · Cited by 70
“Therefore, the here presented concept is fundamentally based on a process-structure-property correlation, i.e. varying process parameters may cause significant changes in electrode structure, which in turn a ff ect cell properties [13].”
InfluentialPesko, D. M., Feng, Z., Sawhney, S., Newman, J., Srinivasan, V., & Balsara, N. P. (2018) · Journal of The Electrochemical Society · doi:10.1149/2.0921813jes · Cited by 68
Self-citationDynamics of Laser-Charged UAVs: A Battery Perspective
Jaafar, W., & Yanıkömeroğlu, H. (2020) · IEEE Internet of Things Journal · doi:10.1109/jiot.2020.3048087 · Cited by 65
“For instance, authors of [29] characterized the battery electro-chemically using six differential equations, while the authors in [30] proposed an electrical circuit-based model.”
MethodHua, X., Zhang, C., & Offer, G. J. (2020) · Journal of Power Sources · doi:10.1016/j.jpowsour.2020.229117 · Cited by 70
“Newman, Doyle, Fuller et al established the foundations for these physics-based model [10,11].”
Ding, S., Li, Y., Dai, H., Wang, L., & He, X. (2023) · Advanced Energy Materials · doi:10.1002/aenm.202301452 · Cited by 75
Mehta, R., & Gupta, A. K. (2023) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2023.114264 · Cited by 66
Solchenbach, S., Tacconis, C., Martin, A. G., Peters, V., Wallisch, L., Stanke, A., Hofer, J., Renz, D., Lewerich, B., Bauer, G., et al. (2024) · Energy & Environmental Science · doi:10.1039/d4ee03211j · Cited by 74
Klett, M., Svens, P. I., Tengstedt, C., Seyeux, A., Światowska, J., Lindbergh, G., & Lindström, R. W. (2014) · The Journal of Physical Chemistry C · doi:10.1021/jp509665e · Cited by 70
Numerical modeling of lithium ion battery for predicting thermal behavior in a cylindrical cell
Jeon, D. H. (2013) · Current Applied Physics · doi:10.1016/j.cap.2013.11.006 · Cited by 69
McCleary, D. A. H., Meyers, J. P., & Kim, B. (2013) · Journal of The Electrochemical Society · doi:10.1149/2.023311jes · Cited by 66
Extending lifetime of portable systems by battery scheduling
Benini, L., Castelli, G., Macii, A., et al. (2001) · doi:10.5555/367072.367151 · Cited by 64
Facile Micro Templating LiFePO4 Electrodes for High Performance Li‐Ion Batteries
Singh, D. P., Mulder, F. M., Abdelkader, A. M., & Wagemaker, M. (2013) · Advanced Energy Materials · doi:10.1002/aenm.201200704 · Cited by 71
Deng, Z., Deng, H., Yang, L., Cai, Y., & Zhao, X. (2017) · Energy · doi:10.1016/j.energy.2017.07.069 · Cited by 64
Sripad, S., & Viswanathan, V. (2017) · Journal of The Electrochemical Society · doi:10.1149/2.0671711jes · Cited by 64
Design considerations for battery-powered electronics
Pedram, M., & Wu, Q. (2003) · Proceedings - ACM IEEE Design Automation Conference · doi:10.1109/dac.1999.782166 · Cited by 64
Lv, Z., Yue, M., Ling, M., Zhang, H., Yan, J., Zheng, Q., & Li, X. (2021) · Advanced Energy Materials · doi:10.1002/aenm.202003725 · Cited by 64
Kim, J. Y., Park, J., Kang, S. H., et al. (2021) · Energy storage materials · doi:10.1016/j.ensm.2021.06.005 · Cited by 63
Qin, P., Liao, M., Mei, W., et al. (2021) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2021.117212 · Cited by 63
Samanta, A., & Williamson, S. S. (2021) · Energies · doi:10.3390/en14185960 · Cited by 65
“Doyle–Fuller–Newmann model [37,61] Pseudo-two-dimensional (P2D) model Not used for temperature estimation but several other researchers used”
MethodCharacterisation and modelling of potassium-ion batteries
Dhir, S., Cattermull, J., Jagger, B., Schart, M., Olbrich, L. F., Chen, Y., Zhao, J., Sada, K., Goodwin, A. L., & Pasta, M. (2024) · Nature Communications · doi:10.1038/s41467-024-51537-w · Cited by 80
Tian, A., Dong, K., Yang, X., Wang, Y., He, L., Gao, Y., & Jiang, J. (2024) · Applied Energy · doi:10.1016/j.apenergy.2024.124748 · Cited by 66
Miehé, C., Mauthe, S., & Ulmer, H. (2014) · International Journal for Numerical Methods in Engineering · doi:10.1002/nme.4700 · Cited by 63
A novel phenomenological multi-physics model of Li-ion battery cells
Oh, K., Samad, N. A., Kim, Y., Siegel, J. B., Stefanopoulou, A. G., & Epureanu, B. I. (2016) · Journal of Power Sources · doi:10.1016/j.jpowsour.2016.07.019 · Cited by 66
On Leakage Current Measured at High Cell Voltages in Lithium-Ion Batteries
Vadivel, N. R., Ha, S., He, M., et al. (2017) · Journal of The Electrochemical Society · doi:10.1149/2.1341702jes · Cited by 63
Estimation of Li-ion Battery State of Health based on Multilayer Perceptron: as an EV Application
Kim, J., Yu, J., Kim, M., Kim, K., & Han, S. (2018) · IFAC-PapersOnLine · doi:10.1016/j.ifacol.2018.11.734 · Cited by 74
Richardson, G. W., Korotkin, I., Ranom, R., Castle, M., & Foster, J. M. (2020) · Electrochimica Acta · doi:10.1016/j.electacta.2020.135862 · Cited by 68
“The current work is focussed on electrode scale modelling of LIBs and is based on the approach developed by Newman and his co-workers in the mid 90’s and early 2000’s [10, 11, 17, 35] which is often referred to as porous electrode theory (PET).”
Yu, M., Li, Y., Podlubný, I., Gong, F., Sun, Y., Zhang, Q., Shang, Y., Duan, B., & Zhang, C. (2020) · Journal of Advanced Research · doi:10.1016/j.jare.2020.06.003 · Cited by 67
Parameter estimation of an electrochemistry-based lithium-ion battery model
Masoudi, R., Uchida, T. K., & McPhee, J. (2015) · Journal of Power Sources · doi:10.1016/j.jpowsour.2015.04.154 · Cited by 65
“Variations of lithium ion concentration in the solid phase can be expressed using Fick's laws of diffusion [17,22], assuming cs,k1⁄4 cs,k(x,r,t):”
BackgroundMethodMao, Z., Farkhondeh, M., Pritzker, M. D., Fowler, M. W., & Chen, Z. (2016) · Electrochimica Acta · doi:10.1016/j.electacta.2016.11.169 · Cited by 64
“To simulate the potential response of the NMC-LMO blended electrode to the intermittent galvanostatic pulses in the GITT experiments, the multi-particle mathematical model presented previously is implemented to describe the lithiation/delithiation dynamics at the particle and electrode scales [22,23].”
MethodA state of health estimation method for electric vehicle Li-ion batteries using GA-PSO-SVR
Zhi, Y., Wang, H., & Wang, L. (2022) · Complex & Intelligent Systems · doi:10.1007/s40747-021-00639-9 · Cited by 73
Zhao, Y., Kumtepeli, V., Ludwig, S., & Jossen, A. (2022) · Journal of Power Sources · doi:10.1016/j.jpowsour.2022.231250 · Cited by 67
BattX: An equivalent circuit model for lithium-ion batteries over broad current ranges
Biju, N., & Fang, H. (2023) · Applied Energy · doi:10.1016/j.apenergy.2023.120905 · Cited by 71
Williams, D., Copley, R. J., Bugryniec, P. J., Dwyer-Joyce, R. S., & Brown, S. (2023) · Journal of Power Sources · doi:10.1016/j.jpowsour.2023.233777 · Cited by 65
Bashash, S., & Fathy, H. K. (2014) · IEEE Transactions on Intelligent Transportation Systems · doi:10.1109/tits.2014.2308283 · Cited by 65
A Battery-Aware Scheme for Routing in Wireless Ad Hoc Networks
Ma, C., & Yang, Y. (2011) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2011.2166093 · Cited by 62
“A higher load electrical current I results in a higher concentration gradient and, thus, a lower concentration of active species at the electrode surface [11].”
BackgroundA Computationally Efficient Approach for Optimizing Lithium-Ion Battery Charging
Liu, J., Li, G., & Fathy, H. K. (2015) · Journal of Dynamic Systems Measurement and Control · doi:10.1115/1.4032066 · Cited by 62
A method for SOC estimation based on simplified mechanistic model for LiFePO4 battery
Li, J., Lai, Q., Wang, L., Lyu, C., & Wang, H. (2016) · Energy · doi:10.1016/j.energy.2016.08.080 · Cited by 63
Optimising lithium-ion cell design for plug-in hybrid and battery electric vehicles
Campbell, I. D., Gopalakrishnan, K., Marinescu, M., Torchio, M., Offer, G. J., & Raimondo, D. (2019) · Journal of Energy Storage · doi:10.1016/j.est.2019.01.006 · Cited by 61
Tran, N. T., Farrell, T., Vilathgamuwa, D. M., Choi, S. S., & Li, Y. (2019) · Journal of The Electrochemical Society · doi:10.1149/2.1241913jes · Cited by 65
Duh, Y., Liu, X., Jiang, X., Kao, C., Gong, L., & Shi, R. (2020) · Journal of Energy Storage · doi:10.1016/j.est.2020.101422 · Cited by 65
An algorithm for state of charge estimation based on a single-particle model
Ren, L., Zhu, G., Kang, J., Wang, J. V., Luo, B., Chen, C., & Xiang, K. (2021) · Journal of Energy Storage · doi:10.1016/j.est.2021.102644 · Cited by 64
Berliner, M. D., Cogswell, D. A., Bazant, M. Z., & Braatz, R. D. (2021) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/ac201c · Cited by 71
Enhanced Lithium-ion battery model considering critical surface charge behavior
Xiong, R., Huang, J., Duan, Y., & Shen, W. (2022) · Applied Energy · doi:10.1016/j.apenergy.2022.118915 · Cited by 62
Saqli, K., Bouchareb, H., M’Sirdi, N. K., & Bentaie, M. O. (2023) · Journal of Energy Storage · doi:10.1016/j.est.2023.107072 · Cited by 67
How to enable large format 4680 cylindrical lithium-ion batteries
Shen, L., Marzook, M. W., Zhang, C., et al. (2023) · Applied Energy · doi:10.1016/j.apenergy.2023.121548 · Cited by 61
Zhang, R., Xiao, Z., Lin, Z., Yan, X., He, Z., Jiang, H., Yang, Z., Jia, X., & Wei, F. (2023) · Nano-Micro Letters · doi:10.1007/s40820-023-01267-3 · Cited by 67
“The overpotential can be decided using the classical Butler–Volmer equation, which is related to the interfacial current I [27–29]: here j 0 denotes the exchange current density, A denotes the electrode area, 𝛼 denotes the charge transfer coefficient that describes the potential landscape at the…”
BackgroundState estimation of lithium-ion battery for shipboard applications: Key challenges and future trends
Kong, L., Luo, Y., Fang, S., Niu, T., Chen, G., Yang, L., & Liao, R. (2024) · Green Energy and Intelligent Transportation · doi:10.1016/j.geits.2024.100192 · Cited by 75
Wang, J., Meng, J., Peng, Q., Liu, T., & Peng, J. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2024.111473 · Cited by 66
Mathematical model of lithium-ion batteries with blended-electrode system
Jung, S. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2014.04.072 · Cited by 62
An Efficient Parallelizable 3D Thermoelectrochemical Model of a Li-Ion Cell
Christensen, J., Cook, D. J., & Albertus, P. S. (2013) · Journal of The Electrochemical Society · doi:10.1149/2.086311jes · Cited by 69
A Boundary Condition for Porous Electrodes
Subramanian, V. R., Tapriyal, D., & White, R. E. (2004) · Electrochemical and Solid-State Letters · doi:10.1149/1.1773751 · Cited by 61
Simulation and Measurement of Local Potentials of Modified Commercial Cylindrical Cells
Erhard, S. V., Osswald, P. J., Wilhelm, J., Rheinfeld, A., Kosch, S., & Jossen, A. (2015) · Journal of The Electrochemical Society · doi:10.1149/2.0431514jes · Cited by 62
Allam, A., & Onori, S. (2018) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2018.2793194 · Cited by 64
Battery Adaptive Observer for a Single-Particle Model With Intercalation-Induced Stress
Zhang, D., Dey, S., Couto, L. D., & Moura, S. J. (2019) · IEEE Transactions on Control Systems Technology · doi:10.1109/tcst.2019.2910797 · Cited by 62
“Doyle–Fuller–Newman model [4]), Li-ion transports in the solid and electrolyte phases.”
BackgroundBattery state of health monitoring by estimation of the number of cyclable Li-ions
Zhou, X., Stein, J. L., & Ersal, T. (2017) · Control Engineering Practice · doi:10.1016/j.conengprac.2017.05.009 · Cited by 60
Sorouri, H., Oshnoei, A., Che, Y., & Teodorescu, R. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2024.113604 · Cited by 62
Modelling of redox flow battery electrode processes at a range of length scales: a review
Chakrabarti, B. K., Kalamaras, E., Singh, A. K., Bertei, A., Rubio‐García, J., Yufit, V., Tenny, K. M., Wu, B., Tariq, F., Hajimolana, Y. S., et al. (2020) · Sustainable Energy & Fuels · doi:10.1039/d0se00667j · Cited by 70
A comparison between physics-based Li-ion battery models
Ali, H. A. A., Raijmakers, L. H. J., Chayambuka, K., Danilov, D. L., Notten, P. H. L., & Eichel, R. (2024) · Electrochimica Acta · doi:10.1016/j.electacta.2024.144360 · Cited by 81
Modeling of nano-structured cathodes for improved lithium-sulfur batteries
Danner, T., Zhu, G., Hofmann, A. F., et al. (2015) · Electrochimica Acta · doi:10.1016/j.electacta.2015.09.143 · Cited by 60
Direct measurement of lithium transport in graphite electrodes using neutrons
Owejan, J. P., Gagliardo, J. J., Harris, S. J., et al. (2012) · Electrochimica Acta · doi:10.1016/j.electacta.2012.01.047 · Cited by 60
Effect of Relaxation Periods over Cycling Performance of a Li-Ion Battery
Rashid, M. M., & Gupta, A. K. (2015) · Journal of The Electrochemical Society · doi:10.1149/2.0201502jes · Cited by 63
A multiphysics microstructure-resolved model for silicon anode lithium-ion batteries
Wang, M., Xiao, X., & Huang, X. (2017) · Journal of Power Sources · doi:10.1016/j.jpowsour.2017.02.037 · Cited by 60
Simulation-Supported Analysis of Calendering Impacts on the Performance of Lithium-Ion-Batteries
Lenze, G., Röder, F., Bockholt, H., Haselrieder, W., Kwade, A., & Krewer, U. (2017) · Journal of The Electrochemical Society · doi:10.1149/2.1141706jes · Cited by 68
Pozzi, A., Ciaramella, G., Volkwein, S., & Raimondo, D. M. (2018) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.8b04580 · Cited by 67
Vora, A. P., Jin, X., Hoshing, V., Saha, T., Shaver, G. M., Varigonda, S., Wasynczuk, O., & Tyner, W. E. (2017) · Applied Energy · doi:10.1016/j.apenergy.2017.05.090 · Cited by 61
Min, J., Gubow, L. M., Hargrave, R. J., Siegel, J. B., & Li, Y. (2023) · Energy & Environmental Science · doi:10.1039/d3ee00953j · Cited by 59
Ji, G., He, L., Wu, T., & Cui, G. (2024) · Applied Energy · doi:10.1016/j.apenergy.2024.124538 · Cited by 76
Gol, A. D., Dermenci, K. B., Farkas, L., & Berecibar, M. (2024) · Advanced Energy Materials · doi:10.1002/aenm.202403255 · Cited by 63
Barai, P., Smith, K. A., Chen, C., Kim, G., & Mukherjee, P. P. (2015) · Journal of The Electrochemical Society · doi:10.1149/2.0241509jes · Cited by 63
Phase Separation Dynamics in Isotropic Ion-Intercalation Particles
Zeng, Y., & Bazant, M. Z. (2014) · SIAM Journal on Applied Mathematics · doi:10.1137/130937548 · Cited by 76
Solute-volume effects in electrolyte transport
Liu, J., & Monroe, C. W. (2014) · Electrochimica Acta · doi:10.1016/j.electacta.2014.05.009 · Cited by 58
“assumed explicitly that (d ln c0/d ln c)T,p ≈ 0, stating that the solvent concentration depended weakly on the electrolyte concentration in the system they considered [29,30].”
BackgroundZeng, Y., Albertus, P. S., Klein, R., Chaturvedi, N. A., Kojić, A., Bazant, M. Z., & Christensen, J. (2013) · Journal of The Electrochemical Society · doi:10.1149/2.102309jes · Cited by 60
Optimal Control of Film Growth in Lithium-Ion Battery Packs via Relay Switches
Moura, S. J., Forman, J. C., Bashash, S., Stein, J. L., & Fathy, H. K. (2010) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2010.2087294 · Cited by 64
“Since these variables vary with respect to space (across the electrodes and separator) and time, they are determined by solving the coupled partial differential equations and algebraic constraints representing the concentration and potential distributions in the solid and solution of the anode, cathode, and separator…”
BackgroundMethodElectrochemical modelling of Li-ion battery pack with constant voltage cycling
Ashwin, T. R., McGordon, A., & Jennings, P. A. (2016) · Journal of Power Sources · doi:10.1016/j.jpowsour.2016.11.092 · Cited by 58
Liang, J., Gan, Y., Song, W., Tan, M., & Li, Y. (2020) · Journal of Energy Storage · doi:10.1016/j.est.2020.101307 · Cited by 59
A Mathematical Model for the Soluble Lead-Acid Flow Battery
Shah, A. A., Li, X., Wills, R. G. A., & Walsh, F. C. (2010) · Journal of The Electrochemical Society · doi:10.1149/1.3328520 · Cited by 68
Battery lifetime prediction for energy-aware computing
Rakhmatov, D. N., Vrudhula, S. B. K., & Wallach, D. A. (2002) · International Symposium on Low Power Electronics and Design (ISLPED) · doi:10.1145/566408.566449 · Cited by 61
Multiscale Lithium-Battery Modeling from Materials to Cells
Li, G., & Monroe, C. W. (2020) · Annual Review of Chemical and Biomolecular Engineering · doi:10.1146/annurev-chembioeng-012120-083016 · Cited by 61
Drees, R., Lienesch, F., & Kurrat, M. (2021) · Journal of Energy Storage · doi:10.1016/j.est.2021.102345 · Cited by 65
Lithium-ion battery physics and statistics-based state of health model
Crawford, A., Choi, D., Balducci, P., Subramanian, V. R., & Viswanathan, V. (2021) · Journal of Power Sources · doi:10.1016/j.jpowsour.2021.230032 · Cited by 63
“7 A m 2 [1,17,52] Converted to kinetic rate constant”
BackgroundMethodA decomposed electrode model for real-time anode potential observation of lithium-ion batteries
Lu, Y., Han, X., Chu, Z., Feng, X., Qin, Y., Ouyang, M., & Lu, L. (2021) · Journal of Power Sources · doi:10.1016/j.jpowsour.2021.230529 · Cited by 62
Metadata
- Authors
- Doyle, M., Fuller, T. F., & Newman, J.
- Affiliations
- Lawrence Berkeley National Laboratory (US)
- Venue
- Journal of The Electrochemical Society
- Publisher
- The Electrochemical Society
- Published
- 1993-06-01
- Volume
- 140
- Issue
- 6
- Pages
- 1526-1533
- ISSN
- 0013-4651 (ISSN-L)
- 1945-7111
- OpenAlex
- W2113449668
- Cited by
- 4,328
- References
- 13
- Citations by year
- 2026: 466 · 2025: 496 · 2024: 401 · 2023: 374 · 2022: 303 · 2021: 306 · 2020: 288 · 2019: 212 · 2018: 190 · 2017: 183 · 2016: 165 · 2015: 150 · 2014: 150 · 2013: 144 · 2012: 109
- FWCI
- 6.42
- Type
- journal article
- Language
- en
- Open access
- bronze
- doi.org
- Licence
- iopscience.iop.org/page/copyright (vor, 9685 d)
- iopscience.iop.org/info/page/text-and-data-mining (tdm, 9685 d)
- Locations
- Journal of The Electrochemical Society (publishedVersion)
- Funders
- U.S. Department of Energy
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Advancements in Battery Materials
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Advanced Battery Materials and Technologies
- Physical Sciences › Engineering › Automotive Engineering › Battery Modeling and Management
- Keywords
- lithium batteries, solid polymer electrolytes, concentrated solution theory, lithium metal anode, superposition method, electrolyte transport, composite cathode, lithium salts
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.