Modeling of Galvanostatic Charge and Discharge of the Lithium/Polymer/Insertion Cell
Open accessThe DOI matches its Crossref record; 13 of the 13 references it cites were found in a registry or an index.
Abstract
The galvanostatic charge and discharge of a lithium anode/solid polymer separator/insertion cathode cell is modeled using concentrated solution theory. The model is general enough to include a wide range of polymeric separator materials, lithium salts, and composite insertion cathodes. Insertion of lithium into the active cathode material is simulated using superposition, thus greatly simplifying the numerical calculations. Variable physical properties are permitted in the model. The results of a simulation of the charge/discharge behavior of the system are presented. Criteria are established to assess the importance of diffusion in the solid matrix and transport in the electrolyte. Consideration is also given to various procedures for optimization of the utilization of active cathode material.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“According to their outcomes, KF output is superior to RLS [91].”
In the citing paper
“Electrochemical models are somewhat more accurate than the classical acoustic ones as being based on the description of the battery's inner chemical processes such as lithium ions diffusion of within the electrodes and the electrolyte [31].”
From Review Paper for SOC Estimation Techniques: Challenges and Future Areas for Improvement (2024) · cites this paper as [31]
Citations
Cites
(1996) · Journal of Power Sources · doi:10.1016/s0378-7753(97)81054-3 · Cited by 463
Experimental Determination of the Transport Number of Water in Nafion 117 Membrane
Fuller, T. F., & Newman, J. (1992) · Journal of The Electrochemical Society · doi:10.1149/1.2069407 · Cited by 278
Self-citationAssessment of Polymer‐Electrolyte Batteries for EV and Ambient Temperature Applications
Gauthier, M., Fauteux, D., Vassort, G., Bélanger, A., Duval, M., Ricoux, P., Chabagno, J. M., Muller, D. A., Rigaud, P., Armand, M. B., et al. (1985) · Journal of The Electrochemical Society · doi:10.1149/1.2114112 · Cited by 156
Formation of a passivating film at the lithium-PEO-LiCF3SO3 interface
Fauteux, D. (1985) · Solid State Ionics · doi:10.1016/0167-2738(85)90061-x · Cited by 134
The fabrication and performance of all solid state polymer-based rechargeable lithium cells
Hooper, A. J., & North, J. M. (1983) · Solid State Ionics · doi:10.1016/0167-2738(83)90146-7 · Cited by 124
Laminar Boundary Layer Flows with Surface Reactions
Acrivos, A., & Chambré, P. L. (1957) · Industrial & Engineering Chemistry · doi:10.1021/ie50570a037 · Cited by 100
Status of rechargeable positive electrodes for ambient temperature lithium batteries
Abraham, K. M. (1981) · Journal of Power Sources · doi:10.1016/0378-7753(81)80058-4 · Cited by 88
A Polymeric Electrolyte Rechargeable Lithium Battery
Bonino, F., Ottaviani, M., Scrosati, B., et al. (1988) · Journal of The Electrochemical Society · doi:10.1149/1.2095538 · Cited by 72
Lithium Electrode/PEO‐Based Polymer Electrolyte Interface Behavior Between 60° and 120°C
Fauteux, D. (1988) · Journal of The Electrochemical Society · doi:10.1149/1.2096244 · Cited by 64
Performance of polymer electrolyte cells at +25 to +100°C
Munshi, M. (1988) · Solid State Ionics · doi:10.1016/0167-2738(88)90244-5 · Cited by 62
Cited by
Items 401–500 of 1,016
Toward Real-Time Simulation of Physics Based Lithium-Ion Battery Models
Subramanian, V. R., Boovaragavan, V., & Diwakar, V. D. (2007) · Electrochemical and Solid-State Letters · doi:10.1149/1.2776128 · Cited by 134
Neutron Imaging of Lithium Concentration in LFP Pouch Cell Battery
Siegel, J. B., Lin, X., Stefanopoulou, A. G., Hussey, D. S., Jacobson, D. L., & Gorsich, D. (2011) · Journal of The Electrochemical Society · doi:10.1149/1.3566341 · Cited by 126
Model Order Reduction of 1D Diffusion Systems Via Residue Grouping
Smith, K. A., Rahn, C. D., & Wang, C. (2008) · Journal of Dynamic Systems Measurement and Control · doi:10.1115/1.2807068 · Cited by 132
Zhao, Y., Patel, Y., Zhang, T., & Offer, G. J. (2018) · Journal of The Electrochemical Society · doi:10.1149/2.0901813jes · Cited by 139
Ohm’s law for ion conduction in lithium and beyond-lithium battery electrolytes
Galluzzo, M. D., Maslyn, J. A., Shah, D. B., et al. (2019) · The Journal of Chemical Physics · doi:10.1063/1.5109684 · Cited by 128
Li, A., Yuen, A. C. Y., Wang, W., Cordeiro, I. M. D. C., Wang, C., Chen, T. B. Y., Zhang, J., Chan, Q. N., & Yeoh, G. H. (2021) · Molecules · doi:10.3390/molecules26020478 · Cited by 157
Andersson, M., Streb, M., Ko, J. Y., Klass, V. L., Klett, M., Ekström, H., Johansson, M., & Lindbergh, G. (2022) · Journal of Power Sources · doi:10.1016/j.jpowsour.2021.230859 · Cited by 142
Recent advances in model-based fault diagnosis for lithium-ion batteries: A comprehensive review
Xu, Y., Ge, X., Guo, R., & Shen, W. (2024) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2024.114922 · Cited by 145
Thermodynamically consistent modeling of elementary electrochemistry in lithium-ion batteries
Colclasure, A. M., & Kee, R. J. (2010) · Electrochimica Acta · doi:10.1016/j.electacta.2010.08.018 · Cited by 131
A three-dimensional multi-physics model for a Li-ion battery
Guo, M., Kim, G., & White, R. E. (2013) · Journal of Power Sources · doi:10.1016/j.jpowsour.2013.03.170 · Cited by 149
Guo, W., Sun, Z., Vilsen, S. B., Meng, J., & Stroe, D. I. (2022) · Journal of Energy Storage · doi:10.1016/j.est.2022.105992 · Cited by 126
“It was designed by Doyle and Newman [28,29] to simulate the whole battery behavior, covering all the essential components of lithium-ion batteries.”
MethodXiao, Y., Wen, J., Yao, L. Y., Zheng, J., Fang, Z., & Shen, Y. (2023) · Journal of Energy Storage · doi:10.1016/j.est.2023.107347 · Cited by 142
Advances in battery state estimation of battery management system in electric vehicles
Jiang, M., Li, D., Li, Z., Chen, Z., Yan, Q., Fu, L., Yu, C., Jiang, B., Wei, X., Yan, W., et al. (2024) · Journal of Power Sources · doi:10.1016/j.jpowsour.2024.234781 · Cited by 154
Goldin, G. M., Colclasure, A. M., Wiedemann, A. H., & Kee, R. J. (2012) · Electrochimica Acta · doi:10.1016/j.electacta.2011.12.119 · Cited by 144
Analysis of pulse and relaxation behavior in lithium-ion batteries
Bernardi, D. M., & Go, J. (2010) · Journal of Power Sources · doi:10.1016/j.jpowsour.2010.06.107 · Cited by 139
Hutzenlaub, T., Thiele, S., Paust, N., Spotnitz, R. M., Zengerle, R., & Walchshofer, C. F. (2013) · Electrochimica Acta · doi:10.1016/j.electacta.2013.10.103 · Cited by 129
Finite Element Thermal Model and Simulation for a Cylindrical Li-Ion Battery
Wang, Z., Ma, J., & Zhang, L. (2017) · IEEE Access · doi:10.1109/access.2017.2723436 · Cited by 126
“proposed an isothermal model for the lithium/polymer/insertion cell under the isotropic condition [14].”
BackgroundFinsterbusch, M., Danner, T., Tsai, C., Uhlenbruck, S., Latz, A., & Guillon, O. (2018) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.8b06705 · Cited by 130
Liu, X., Zhang, X., Chen, X., Zhu, G., Yan, C., Huang, J., & Peng, H. (2021) · Journal of Energy Chemistry · doi:10.1016/j.jechem.2021.12.004 · Cited by 130
Semerukhin, D. Y., Kubarkov, A. V., Sergeyev, V. G., Semenikhin, O. A., & Antipov, E. V. (2024) · Electrochimica Acta · doi:10.1016/j.electacta.2024.144092 · Cited by 134
Deep Learning in the State of Charge Estimation for Li-Ion Batteries of Electric Vehicles: A Review
Zhang, D., Zhong, C., Xu, P., & Tian, Y. (2022) · Machines · doi:10.3390/machines10100912 · Cited by 131
Zhang, L., Lyu, C., Hinds, G., Wang, L., Luo, W., Zheng, J., & Ma, K. (2014) · Journal of The Electrochemical Society · doi:10.1149/2.048405jes · Cited by 126
Safety issues of defective lithium-ion batteries: identification and risk evaluation
Jia, Y., Liu, B., Hong, Z., Yin, S., Finegan, D. P., & Xu, J. (2020) · Journal of Materials Chemistry A · doi:10.1039/d0ta04171h · Cited by 124
Lin, M., Yan, C., Meng, J., Wang, W., & Wu, J. (2022) · Energy · doi:10.1016/j.energy.2022.123829 · Cited by 123
Yan, B., Lim, C., Yin, L., et al. (2012) · Journal of The Electrochemical Society · doi:10.1149/2.024210jes · Cited by 125
Sun, T., Shen, T., Zheng, Y., Ren, D., Zhu, W., Li, J., Wang, Y., Kuang, K., Rui, X., Wang, S., et al. (2022) · Electrochimica Acta · doi:10.1016/j.electacta.2022.140701 · Cited by 134
A multi-scale approach for the stress analysis of polymeric separators in a lithium-ion battery
Xiao, X., Wu, W., & Huang, X. (2010) · Journal of Power Sources · doi:10.1016/j.jpowsour.2010.06.020 · Cited by 123
Multiscale modeling of lithium-ion battery electrodes based on nano-scale X-ray computed tomography
Kashkooli, A. G., Farhad, S., Lee, D. U., Feng, K., Litster, S., Babu, S. K., Zhu, L., & Chen, Z. (2016) · Journal of Power Sources · doi:10.1016/j.jpowsour.2015.12.134 · Cited by 128
“Generally, in traditional LIB modeling tortuosity is calculated using Bruggeman correlation [9,10,49].”
MethodFeng, X., He, X., Lu, L., & Ouyang, M. (2018) · Journal of The Electrochemical Society · doi:10.1149/2.0501802jes · Cited by 126
The polarization characteristics of lithium-ion batteries under cyclic charge and discharge
Qiu, C., He, G., Shi, W., et al. (2019) · Journal of Solid State Electrochemistry · doi:10.1007/s10008-019-04282-w · Cited by 123
Optimum fast charging of lithium-ion pouch cells based on local volume expansion criteria
Spingler, F. B., Wittmann, W., Sturm, J., Rieger, B., & Jossen, A. (2018) · Journal of Power Sources · doi:10.1016/j.jpowsour.2018.04.095 · Cited by 122
Electrochemistry-based Battery Modeling for Prognostics
Daigle, M., & S. Kulkarni, C. (2013) · Annual Conference of the PHM Society · doi:10.36001/phmconf.2013.v5i1.2252 · Cited by 119
A systematic review of thermal management techniques for electric vehicle batteries
Kharabati, S., & Saedodin, S. (2023) · Journal of Energy Storage · doi:10.1016/j.est.2023.109586 · Cited by 150
An alternating current heating method for lithium-ion batteries from subzero temperatures
Zhu, J., Sun, Z., Wei, X., & Dai, H. (2016) · International Journal of Energy Research · doi:10.1002/er.3576 · Cited by 124
“The electrode reaction current can be calculated from the BVE [38] and the over-potential of the intercalation reaction [39].”
BackgroundA Study on the Effect of Porosity and Particles Size Distribution on Li-Ion Battery Performance
Taleghani, S. T., Marcos, B., Zaghib, K., et al. (2017) · Journal of The Electrochemical Society · doi:10.1149/2.0211711jes · Cited by 121
Wu, B., & Lu, W. D. (2017) · Journal of Power Sources · doi:10.1016/j.jpowsour.2017.05.115 · Cited by 120
Application of artificial neural networks in design of lithium-ion batteries
Wu, B., Han, S., Shin, K. G., & Lu, W. (2018) · Journal of Power Sources · doi:10.1016/j.jpowsour.2018.05.040 · Cited by 120
Visualizing the Carbon Binder Phase of Battery Electrodes in Three Dimensions
Daemi, S. R., Tan, C., Volkenandt, T., Cooper, S. J., Palacios-Padros, A., Cookson, J., Brett, D. J. L., & Shearing, P. R. (2018) · ACS Applied Energy Materials · doi:10.1021/acsaem.8b00501 · Cited by 122
Charging Optimization for Li-Ion Battery in Electric Vehicles: A Review
Chen, C., Wei, Z., & Knoll, A. (2021) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2021.3135525 · Cited by 137
“Newman’s group [55] based on the porous electrode theory.”
BackgroundLin, M., Yan, C., Wang, W., Dong, G., Meng, J., & Wu, J. (2023) · Energy · doi:10.1016/j.energy.2023.127675 · Cited by 134
Dees, D. W., Gunen, E., Abraham, D. P., Jansen, A. N., & Prakash, J. (2008) · Journal of The Electrochemical Society · doi:10.1149/1.2939211 · Cited by 121
Effect of Anode Film Resistance on the Charge/Discharge Capacity of a Lithium-Ion Battery
Christensen, J., & Newman, J. (2003) · Journal of The Electrochemical Society · doi:10.1149/1.1612501 · Cited by 121
Self-citationA SEI Modeling Approach Distinguishing between Capacity and Power Fade
Kindermann, F. M., Keil, J., Frank, A., & Jossen, A. (2017) · Journal of The Electrochemical Society · doi:10.1149/2.0321712jes · Cited by 140
Deng, Z., Yang, L., Deng, H., Cai, Y., & Li, D. (2017) · Energy · doi:10.1016/j.energy.2017.10.097 · Cited by 123
Optimal cell tab design and cooling strategy for cylindrical lithium-ion batteries
Shen, L., Kirkaldy, N., Zhang, C., Gopalakrishnan, K., Amietszajew, T., Diaz, L. B., Barreras, J. V., Shams, M., Hua, X., Patel, Y., et al. (2021) · Journal of Power Sources · doi:10.1016/j.jpowsour.2021.229594 · Cited by 119
“A cell-level pseudo two-dimensional (P2D) physics-based model [29–32] is computationally intensive.”
BackgroundHigh rate discharge capability of single particle electrode of LiCoO2
Dokko, K., Nakata, N., & Kanamura, K. (2008) · Journal of Power Sources · doi:10.1016/j.jpowsour.2008.07.081 · Cited by 120
A Hybrid Ensemble Deep Learning Approach for Early Prediction of Battery Remaining Useful Life
Xu, Q., Wu, M., Khoo, E., Chen, Z., & Li, X. (2023) · IEEE/CAA Journal of Automatica Sinica · doi:10.1109/jas.2023.123024 · Cited by 119
“Physics-based approaches such as the single particle model (SPM) [8], [9] and pseudo-two-dimensional (P2D) model [10], [11], [12], [13], [14] are based on the electrochemical principles underlying LIBs and can simulate a battery’s current and voltage characteristics from kinetics and transport equations.”
MethodA New Method to Model the Thickness Change of a Commercial Pouch Cell during Discharge
Rieger, B., Erhard, S. V., Rumpf, K., & Jossen, A. (2016) · Journal of The Electrochemical Society · doi:10.1149/2.0441608jes · Cited by 126
Smith, K. C. (2017) · Electrochimica Acta · doi:10.1016/j.electacta.2017.02.006 · Cited by 124
Heat and mass transfer modeling and assessment of a new battery cooling system
Al‐Zareer, M., Dinçer, İ., & Rosen, M. A. (2018) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2018.04.157 · Cited by 121
Zhang, M., Chouchane, M., Shojaee, S. A., Winiarski, B., Liu, Z., Li, L., Pelapur, R., Shodiev, A., Yao, W., Doux, J., et al. (2022) · Joule · doi:10.1016/j.joule.2022.12.001 · Cited by 122
Li, R., Kirkaldy, N., Oehler, F. F., Marinescu, M., Offer, G. J., & O’Kane, S. E. J. (2025) · Nature Communications · doi:10.1038/s41467-025-57968-3 · Cited by 170
Morasch, R., Landesfeind, J., Suthar, B., & Gasteiger, H. A. (2018) · Journal of The Electrochemical Society · doi:10.1149/2.1021814jes · Cited by 123
Research progress in fault detection of battery systems: A review
Shang, Y., Wang, S., Tang, N., Fu, Y., & Wang, K. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2024.113079 · Cited by 126
Zhao, S., Duncan, S. R., & Howey, D. A. (2017) · IEEE Transactions on Control Systems Technology · doi:10.1109/tcst.2016.2542115 · Cited by 116
“On the other hand, electrochemical models such as the pseudo-2-D (P2D) model [3] are derived from electrochemical principles and usually characterized by partial differential equations coupled with algebraic”
MethodBattery discharge characteristics of wireless sensor nodes: an experimental analysis
Park, C., Lahiri, K., & Raghunathan, A. (2005) · doi:10.1109/sahcn.2005.1557096 · Cited by 117
“For our studies we use an experimental test-bed comprising MICA2 hardware [3], commercial lithium-coin batteries [4] and a combination of several techniques for battery discharge analysis, including measurements on actual batteries, an accurately calibrated version of the low-level battery simulator Dualfoil [ 5 ], an…”
BackgroundMethodInfluentialA modeling and experimental study of capacity fade for lithium-ion batteries
Carnovale, A., & Li, X. (2020) · Energy and AI · doi:10.1016/j.egyai.2020.100032 · Cited by 124
Predicting battery end of life from solar off-grid system field data using machine learning
Aitio, A., & Howey, D. A. (2021) · Joule · doi:10.1016/j.joule.2021.11.006 · Cited by 116
Lee, B., Yoon, J., Jung, C., Kim, D. Y., Jeon, S., Kim, K., Park, J., Park, H. S., Lee, K. H., Kang, Y., et al. (2016) · ACS Nano · doi:10.1021/acsnano.5b07674 · Cited by 116
A novel approach for performance improvement of liquid to vapor based battery cooling systems
Al‐Zareer, M., Dinçer, İ., & Rosen, M. A. (2019) · Energy Conversion and Management · doi:10.1016/j.enconman.2019.02.063 · Cited by 115
Theory and Applications of Macroscale Models in Porous Media
Battiato, I., Ferrero, P. T., Malley, D. O., Miller, C. T., Takhar, P. S., Valdés‐Parada, F. J., & Wood, B. D. (2019) · Transport in Porous Media · doi:10.1007/s11242-019-01282-2 · Cited by 124
“Homogenization theory has been applied to a large variety of problems in physics, engineering, environmental sciences, since its first elaboration and application to the study of composite materials in the 1970 and 1980s. The theoretical foundations of the approach were first developed in two seminal papers by Spagnol…”
BackgroundLi, F., Zuo, W., Zhou, K., Li, Q., Huang, Y., & Zhang, G. (2023) · Energy · doi:10.1016/j.energy.2023.130025 · Cited by 132
Advances and challenges in thermal runaway modeling of lithium-ion batteries
Wang, G., Ping, P., Kong, D., Peng, R., He, X., Zhang, Y., Dai, X., & Wen, J. X. (2024) · The Innovation · doi:10.1016/j.xinn.2024.100624 · Cited by 228
“The widely used pseudo-two-dimensional model, pioneered by Newman ’ s group, 125 applies concentrated solution theory and porous electrode theory, with subsequent simpli fi cations including the porous electrode model with polynomial approximation and the single-particle model (see supplemental…”
Modeling and Optimal Operation of Distributed Battery Storage in Low Voltage Grids
Fortenbacher, P., Mathieu, J. L., & Andersson, G. (2017) · IEEE Transactions on Power Systems · doi:10.1109/tpwrs.2017.2682339 · Cited by 118
“To study the RT controller, we simulate its performance on a sunny day and use the DUALFOIL electrochemical battery model [41] in place of a real battery system.”
MethodKhan, N., Ooi, C. A., Alturki, A., Amir, M., Shreasth, S., & Alharbi, T. (2024) · Energy Reports · doi:10.1016/j.egyr.2024.04.041 · Cited by 142
Mechanical Deformation of a Lithium-Metal Anode Due to a Very Stiff Separator
Ferrese, A., & Newman, J. (2014) · Journal of The Electrochemical Society · doi:10.1149/2.0911409jes · Cited by 117
Self-citationIn-Situ Measurement of Current Distribution in a Li-Ion Cell
Zhang, G., Shaffer, C. E., Wang, C., & Rahn, C. D. (2013) · Journal of The Electrochemical Society · doi:10.1149/2.046304jes · Cited by 115
On Graded Electrode Porosity as a Design Tool for Improving the Energy Density of Batteries
Dai, Y., & Srinivasan, V. (2015) · Journal of The Electrochemical Society · doi:10.1149/2.0301603jes · Cited by 123
Metal‐Ion Coupled Electron Transfer Kinetics in Intercalation‐Based Transition Metal Oxides
Nikitina, V. A., Vassiliev, S. Y., & Stevenson, K. J. (2020) · Advanced Energy Materials · doi:10.1002/aenm.201903933 · Cited by 120
An improved single particle model for lithium-ion batteries based on main stress factor compensation
Tian, J., Wang, Y., & Chen, Z. (2020) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2020.123456 · Cited by 133
Quadruple the rate capability of high-energy batteries through a porous current collector design
Ye, Y., Xu, R., Huang, W., Ai, H., Zhang, W., Affeld, J. O., Cui, A., Liu, F., Gao, X., Chen, Z., et al. (2024) · Nature Energy · doi:10.1038/s41560-024-01473-2 · Cited by 144
Effect of Porosity, Thickness and Tortuosity on Capacity Fade of Anode
Suthar, B., Northrop, P. W. C., Rife, D., & Subramanian, V. R. (2015) · Journal of The Electrochemical Society · doi:10.1149/2.0061509jes · Cited by 127
Baba, N., Yoshida, H., Nagaoka, M., Okuda, C., & Kawauchi, S. (2013) · Journal of Power Sources · doi:10.1016/j.jpowsour.2013.11.111 · Cited by 111
Intercalation Kinetics in Multiphase-Layered Materials
Smith, R. B., Khoo, E., & Bazant, M. Z. (2017) · The Journal of Physical Chemistry C · doi:10.1021/acs.jpcc.7b00185 · Cited by 120
Kindermann, F. M., Noel, A., Erhard, S. V., & Jossen, A. (2015) · Electrochimica Acta · doi:10.1016/j.electacta.2015.10.108 · Cited by 119
Ultrafast charging of energy-dense lithium-ion batteries for urban air mobility
Liu, T., Yang, X., Ge, S., Leng, Y., & Wang, C. (2021) · eTransportation · doi:10.1016/j.etran.2021.100103 · Cited by 121
Saxena, S., Ward, L. T., Kubal, J., Lu, W., Babinec, S., & Paulson, N. H. (2022) · Journal of Power Sources · doi:10.1016/j.jpowsour.2022.231736 · Cited by 112
A review of stochastic battery models and health management
Tao, L., Ma, J., Cheng, Y., Noktehdan, A., Chong, J., & Lü, C. (2017) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2017.05.127 · Cited by 120
Lagadec, M. F., Zahn, R., Müller, S., & Wood, V. C. (2018) · Energy & Environmental Science · doi:10.1039/c8ee00875b · Cited by 114
A scaling law to determine phase morphologies during ion intercalation
Fraggedakis, D., Nadkarni, N., Gao, T., Zhou, T., Zhang, Y. A., Yu, H., Stephens, R., Shao‐Horn, Y., & Bazant, M. Z. (2020) · Energy & Environmental Science · doi:10.1039/d0ee00653j · Cited by 106
He, T., Zhang, T., Wang, Z., & Cai, Q. (2022) · Applied Energy · doi:10.1016/j.apenergy.2022.118797 · Cited by 111
Modeling Internal Shorting Process in Large-Format Li-Ion Cells
Zhao, W., Luo, G., & Wang, C.-Y. (2015) · Journal of The Electrochemical Society · doi:10.1149/2.1031507jes · Cited by 116
Al-janabi, A., Kavgic, M., Mohammadzadeh, A., et al. (2018) · Journal of Building Engineering · doi:10.1016/j.jobe.2018.12.022 · Cited by 109
Modeling of thermal runaway propagation of NMC battery packs after fast charging operation
Wang, W., He, T., He, S., You, T., & Khan, F. I. (2021) · Process Safety and Environmental Protection · doi:10.1016/j.psep.2021.08.006 · Cited by 108
Kim, J., Chun, H., Baek, J., & Han, S. (2021) · Journal of Energy Storage · doi:10.1016/j.est.2021.103571 · Cited by 109
Quantifying the factors limiting rate performance in battery electrodes
Tian, R., Park, S., King, P. J., et al. (n.d.) · RePEc: Research Papers in Economics · Cited by 109
Xu, X., & He, R. (2013) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2013.08.057 · Cited by 107
Lithium-ion battery life prognostic health management system using particle filtering framework
Dalal, M., Ma, J., & He, D. (2011) · Proceedings of the Institution of Mechanical Engineers, Part O: Journal of Risk and Reliability · doi:10.1177/1748006xjrr342 · Cited by 108
State of Health Estimation Methods for Lithium-Ion Batteries
Nuroldayeva, G., Serik, Y., Adair, D., Uzakbaiuly, B., & Bakenov, Z. (2023) · International Journal of Energy Research · doi:10.1155/2023/4297545 · Cited by 137
“This approach is abbreviated as the DFN model (Doyle-Fuller-Newman) [75, 76].”
From Present Innovations to Future Potential: The Promising Journey of Lithium-Ion Batteries
Parvizi, P., Jalilian, M., Amidi, A. M., Zangeneh, M. R., & Riba, J. (2025) · Micromachines · doi:10.3390/mi16020194 · Cited by 137
Amiribavandpour, P., Shen, W., Mu, D., & Kapoor, A. (2015) · Journal of Power Sources · doi:10.1016/j.jpowsour.2015.03.022 · Cited by 105
Dynamics and morphology of solid electrolyte interphase (SEI)
Single, F., Horstmann, B., & Latz, A. (2016) · Physical Chemistry Chemical Physics · doi:10.1039/c6cp02816k · Cited by 117
Mesoscale modeling in electrochemical devices—A critical perspective
Ryan, E. M., & Mukherjee, P. P. (2018) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2018.11.002 · Cited by 111
Theory of Impedance Spectroscopy for Lithium Batteries
Single, F., Horstmann, B., & Latz, A. (2019) · The Journal of Physical Chemistry C · doi:10.1021/acs.jpcc.9b07389 · Cited by 111
Lu, X., Zhang, X., Tan, C., Heenan, T. M. M., Lagnoni, M., O’Regan, K. B., Daemi, S. R., Bertei, A., Jones, H. G., Hinds, G., et al. (2021) · Energy & Environmental Science · doi:10.1039/d1ee01388b · Cited by 107
Ragone plots revisited: A review of methodology and application across energy storage technologies
Beyers, I., Bensmann, A., & Hanke‐Rauschenbach, R. (2023) · Journal of Energy Storage · doi:10.1016/j.est.2023.109097 · Cited by 119
Stetzel, K. D., Aldrich, L. L., Trimboli, M. S., & Plett, G. L. (2015) · Journal of Power Sources · doi:10.1016/j.jpowsour.2014.11.135 · Cited by 106
Liu, G., Ouyang, M., Lu, L., Li, J., & Hua, J. (2015) · Applied Energy · doi:10.1016/j.apenergy.2015.03.110 · Cited by 109
“There exist a number of studies on lithium-ion battery models [32–35], in which the equivalent circuit model (ECM) is widely used in onboard state estimation cases and implemented here for its low complexity.”
BackgroundLin, C. W., Tang, A., & Xing, J. (2017) · Applied Energy · doi:10.1016/j.apenergy.2017.05.109 · Cited by 110
Atkins, D., Ayerbe, E., Benayad, A., Capone, F. G., Capria, E., Castelli, I. E., Cekić-Lasković, I., Aylagas, R. C., Dudy, L., Edström, K., et al. (2021) · Advanced Energy Materials · doi:10.1002/aenm.202102687 · Cited by 117
Metadata
- Authors
- Doyle, M., Fuller, T. F., & Newman, J.
- Affiliations
- Lawrence Berkeley National Laboratory (US)
- Venue
- Journal of The Electrochemical Society
- Publisher
- The Electrochemical Society
- Published
- 1993-06-01
- Volume
- 140
- Issue
- 6
- Pages
- 1526-1533
- ISSN
- 0013-4651 (ISSN-L)
- 1945-7111
- OpenAlex
- W2113449668
- Cited by
- 4,328
- References
- 13
- Citations by year
- 2026: 466 · 2025: 496 · 2024: 401 · 2023: 374 · 2022: 303 · 2021: 306 · 2020: 288 · 2019: 212 · 2018: 190 · 2017: 183 · 2016: 165 · 2015: 150 · 2014: 150 · 2013: 144 · 2012: 109
- FWCI
- 6.42
- Type
- journal article
- Language
- en
- Open access
- bronze
- doi.org
- Licence
- iopscience.iop.org/page/copyright (vor, 9685 d)
- iopscience.iop.org/info/page/text-and-data-mining (tdm, 9685 d)
- Locations
- Journal of The Electrochemical Society (publishedVersion)
- Funders
- U.S. Department of Energy
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Advancements in Battery Materials
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Advanced Battery Materials and Technologies
- Physical Sciences › Engineering › Automotive Engineering › Battery Modeling and Management
- Keywords
- lithium batteries, solid polymer electrolytes, concentrated solution theory, lithium metal anode, superposition method, electrolyte transport, composite cathode, lithium salts
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.