Microfluidic Production of Multiple Emulsions
Open accessThe DOI matches its Crossref record; 133 of the 133 references it cites were found in a registry or an index.
Abstract
Microfluidic devices are promising tools for the production of monodispersed tuneable complex emulsions. This review highlights the advantages of microfluidics for the fabrication of emulsions and presents an overview of the microfluidic emulsification methods including two-step and single-step methods for the fabrication of high-order multiple emulsions (double, triple, quadruple and quintuple) and emulsions with multiple and/or multi-distinct inner cores. The microfluidic methods for the formation of multiple emulsion drops with ultra-thin middle phase, multi-compartment jets, and Janus and ternary drops composed of two or three distinct surface regions are also presented. Different configurations of microfluidic drop makers are covered, such as co-flow, T-junctions and flow focusing (both planar and three-dimensional (3D)). Furthermore, surface modifications of microfluidic channels and different modes of droplet generation are summarized. Non-confined microfluidic geometries used for buoyancy-driven drop generation and membrane integrated microfluidics are also discussed. The review includes parallelization and drop splitting strategies for scaling up microfluidic emulsification. The productivity of a single drop maker is typically <1 mL/h; thus, more than 1000 drop makers are needed to achieve commercially relevant droplet throughputs of >1 L/h, which requires combining drop makers into twodimensional (2D) and 3D assemblies fed from a single set of inlet ports through a network of distribution and collection channels.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
The origins and the future of microfluidics
Whitesides, G. M. (2006) · Nature · doi:10.1038/nature05058 · Cited by 9,687 · cited 1×
“Using this technique, however, it is not possible to control the number of inner droplets [49,50] and to encapsulate different types of inner droplets in the same outer drop [19,51,52].”
MethodXia, Y., & Whitesides, G. M. (1998) · Annual Review of Materials Science · doi:10.1146/annurev.matsci.28.1.153 · Cited by 4,611
Poly(dimethylsiloxane) as a Material for Fabricating Microfluidic Devices
McDonald, J. C., & Whitesides, G. M. (2002) · Accounts of Chemical Research · doi:10.1021/ar010110q · Cited by 2,454 · cited 1×
“The most common devices for microfluidic production of complex droplets and microjets are coaxial assemblies of glass capillaries [55] and planar microfluidic devices [53].”
BackgroundFormation of droplets and bubbles in a microfluidic T-junction—scaling and mechanism of break-up
Garstecki, P., Fuerstman, M. J., Stone, H. A., & Whitesides, G. M. (2006) · Lab on a Chip · doi:10.1039/b510841a · Cited by 2,339 · cited 3×
“Due to excessive compressive force from the continuous phase, the dispersed phase neck is squeezed until it pinches off into drops [86,98,99], as shown in Figure 2f.”
BackgroundMethodFormation of dispersions using “flow focusing” in microchannels
Anna, S. L., Bontoux, N., & Stone, H. A. (2003) · Applied Physics Letters · doi:10.1063/1.1537519 · Cited by 2,302 · cited 1×
“Using this technique, however, it is not possible to control the number of inner droplets [49,50] and to encapsulate different types of inner droplets in the same outer drop [19,51,52].”
MethodMonodisperse Double Emulsions Generated from a Microcapillary Device
Utada, A. S., Lorenceau, E., Link, D. R., Kaplan, P. D., Stone, H. A., & Weitz, D. A. (2005) · Science · doi:10.1126/science.1109164 · Cited by 2,248 · cited 7×
“[14] has introduced a glass capillary device for the single-step generation of double emulsions.”
BackgroundInfluentialCho, S. K., Moon, H., & Kim, C.-J. (2003) · Journal of Microelectromechanical Systems · doi:10.1109/jmems.2002.807467 · Cited by 1,598
Poly(lactic acid) fiber: An overview
Gupta, B., Revagade, N., & Hilborn, J. (2007) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2007.01.005 · Cited by 1,360 · cited 1×
“Common methods used for the fabrication of microfibers are self-assembly [162], wet spinning [163], electrospinning [161,164] and electro-wet spinning [165].”
MethodPeptide-amphiphile nanofibers: A versatile scaffold for the preparation of self-assembling materials
Hartgerink, J. D., Beniash, E., & Stupp, S. I. (2002) · Proceedings of the National Academy of Sciences · doi:10.1073/pnas.072699999 · Cited by 1,240 · cited 1×
“Common methods used for the fabrication of microfibers are self-assembly [162], wet spinning [163], electrospinning [161,164] and electro-wet spinning [165].”
MethodAn electrophoretic ink for all-printed reflective electronic displays
Comiskey, B., Albert, J. D., Yoshizawa, H., & Jacobson, J. (1998) · Nature · doi:10.1038/28349 · Cited by 1,123 · cited 1×
“Emulsions are dispersion of stabilised liquids within a continuous immiscible liquid, and has long been used in a verity of applications including production of pharmaceuticals [1–3], cosmetics [4], foods [5], electronics [6], and energy-related [7–10].”
BackgroundSpinning Continuous Fibers for Nanotechnology
Dzenis, Y. (2004) · Science · doi:10.1126/science.1099074 · Cited by 1,110 · cited 1×
“Common methods used for the fabrication of microfibers are self-assembly [162], wet spinning [163], electrospinning [161,164] and electro-wet spinning [165].”
MethodControlled microfluidic interfaces
Atencia, J., & Beebe, D. J. (2005) · Nature · doi:10.1038/nature04163 · Cited by 1,006 · cited 1×
“Using this technique, however, it is not possible to control the number of inner droplets [49,50] and to encapsulate different types of inner droplets in the same outer drop [19,51,52].”
MethodDripping to Jetting Transitions in Coflowing Liquid Streams
Utada, A. S., Fernandez-Nieves, A., Stone, H. A., & Weitz, D. A. (2007) · Physical Review Letters · doi:10.1103/physrevlett.99.094502 · Cited by 965 · cited 2×
“The size of droplets in jetting mode can be calculated using Equation (2) [83]:”
BackgroundMethodElectric Control of Droplets in Microfluidic Devices
Link, D. R., Grasland‐Mongrain, E., Duri, A., Sarrazin, F., Cheng, Z., Cristobal, G., Márquez, M., & Weitz, D. A. (2006) · Angewandte Chemie International Edition · doi:10.1002/anie.200503540 · Cited by 843 · cited 4×
“Electric control of charged droplets in icrofluidic channels: (a) coalescence; (b) splitting control; (c) sorting control [179].”
BackgroundMethodInfluentialDesigner emulsions using microfluidics
Shah, R. K., Shum, H. C., Rowat, A. C., Lee, D., Agresti, J. J., Utada, A. S., Chu, L.-Y., Kim, J.-W., Fernandez-Nieves, A., Martinez, C. J., et al. (2008) · Materials Today · doi:10.1016/s1369-7021(08)70053-1 · Cited by 766 · cited 3×
“A significant advantage of glass capillaries is the straightforward control over their wettability by a surface reaction with an appropriate silane coupling agent [55].”
BackgroundControllable Monodisperse Multiple Emulsions
Chu, L., Utada, A. S., Shah, R. K., Kim, J., & Weitz, D. A. (2007) · Angewandte Chemie International Edition · doi:10.1002/anie.200701358 · Cited by 747 · cited 6×
“Double emulsions were generated in two emulsification steps using two co-flow drop makers [54].”
BackgroundMethodInfluentialTransition from squeezing to dripping in a microfluidic T-shaped junction
DE MENECH, M., GARSTECKI, P., JOUSSE, F., & STONE, H. A. (2008) · Journal of Fluid Mechanics · doi:10.1017/s002211200700910x · Cited by 728 · cited 1×
“Due to excessive compressive force from the continuous phase, the dispersed phase neck is squeezed until it pinches off into drops [86,98,99], as shown in Figure 2f.”
BackgroundNisisako, T., Torii, T., Takahashi, T., & Takizawa, Y. (2006) · Advanced Materials · doi:10.1002/adma.200502431 · Cited by 724 · cited 8×
“The two dispersed phases could be a photopolymerizable phase and a nonotopolymerizable phase (silicon oil) [155], two ifferently coloured m omer streams containing whit and black pigments [152,156], two pre-polymer solutions with and without fluorescently labelled molecules [64], nd two pre-polymer streams with and wi…”
BackgroundMethodInfluentialMonodisperse Emulsion Generation via Drop Break Off in a Coflowing Stream
Umbanhowar, P. B., Prasad, V., & Weitz, D. A. (2000) · Langmuir · doi:10.1021/la990101e · Cited by 693 · cited 1×
“Using this technique, however, it is not possible to control the number of inner droplets [49,50] and to encapsulate different types of inner droplets in the same outer drop [19,51,52].”
MethodNie, Z., Li, W., Seo, M., Xu, S., & Kumacheva, E. (2006) · Journal of the American Chemical Society · doi:10.1021/ja060882n · Cited by 689 · cited 3×
“Janus droplets produced in microfluidic devices are used as templates for the production of Janus particles that contain two sides with different properties [17,152,153].”
BackgroundMethodOkushima, S., Nisisako, T., Torii, T., & Higuchi, T. (2004) · Langmuir · doi:10.1021/la0480336 · Cited by 656 · cited 12×
“A series of two T-junctions [52,70,110], two flow-focusing units [76,111,112], two cross junctions [113–115], ad one T-junction combi ed with one flo -focusing”
BackgroundMethodInfluentialDrop formation in a co-flowing ambient fluid
Cramer, C., Fischer, P., & Windhab, E. J. (2004) · Chemical Engineering Science · doi:10.1016/j.ces.2004.04.006 · Cited by 538 · cited 2×
“In the co-flow geometry, the dispersed phase is delivered through the tapered injection tube and the continuous phase is introduced from the same direction through the coaxial area between the square capillary and the injection capillary tube [135,136].”
BackgroundMethodPolymer Particles with Various Shapes and Morphologies Produced in Continuous Microfluidic Reactors
Nie, Z., Xu, S., Seo, M., Lewis, P. C., & Kumacheva, E. (2005) · Journal of the American Chemical Society · doi:10.1021/ja042494w · Cited by 531 · cited 4×
“Schematic of production of double emulsion droplets in microfluidic flow focusing planar device with co-flow flow focusing geometry [118].”
MethodInfluentialMultiphase flow microfluidics for the production of single or multiple emulsions for drug delivery
Zhao, C.-X. (2013) · Advanced Drug Delivery Reviews · doi:10.1016/j.addr.2013.05.009 · Cited by 451 · cited 1×
“A common method is using oxygen plasma to oxidize the PDMS surface [73], but the surface hydrophobicity is restored after several minutes to several hours [74], which makes PDMS devices difficult to use for applications that require stable hydrophilic surface property.”
MethodDynamically reconfigurable complex emulsions via tunable interfacial tensions
Zarzar, L. D., Sresht, V., Sletten, E. M., Kalow, J. A., Blankschtein, D., & Swager, T. M. (2015) · Nature · doi:10.1038/nature14168 · Cited by 430 · cited 2×
“and can be prepared using various immiscible sets of oils [62], s ch as fluorocarbon and hydrocarbon oils.”
BackgroundNisisako, T., & Torii, T. (2008) · Lab Chip · doi:10.1039/b713141k · Cited by 415 · cited 2×
“Possible scaling-up approaches are parallelization of drop makers [199,200] and/or drop splitting [201–204].”
BackgroundDripping and jetting in microfluidic multiphase flows applied to particle and fibre synthesis
Nunes, J. K., Tsai, S. S. H., Wan, J., & Stone, H. A. (2013) · Journal of Physics D: Applied Physics · doi:10.1088/0022-3727/46/11/114002 · Cited by 406
Design of microencapsulated chitosan microspheres for colonic drug delivery
Lorenzo-Lamosa, M. L., Remuñán-López, C., Vila-Jato, J. L., & Alonso, M. J. (1998) · Journal of Controlled Release · doi:10.1016/s0168-3659(97)00203-4 · Cited by 402
Multiple emulsions for food use
Muschiolik, G. (2007) · Current Opinion in Colloid & Interface Science · doi:10.1016/j.cocis.2007.07.006 · Cited by 377 · cited 2×
“from the large production scales which make them applicable in some industries such as food and cosmetic where t e drop size uniformity is not critical [40,41].”
BackgroundProduction of uniform droplets using membrane, microchannel and microfluidic emulsification devices
Vladisavljević, G. T., Kobayashi, I., & Nakajima, M. (2012) · Microfluidics and Nanofluidics · doi:10.1007/s10404-012-0948-0 · Cited by 374
Self-citationMicrofluidic Production of Biopolymer Microcapsules with Controlled Morphology
Zhang, H., Tumarkin, E., Peerani, R., Nie, Z., Sullan, R. M. A., Walker, G. C., & Kumacheva, E. (2006) · Journal of the American Chemical Society · doi:10.1021/ja0635682 · Cited by 374 · cited 1×
“The same device was used by Zhang and co-workers [119] for the production of hydrogel capsules.”
MethodMicrofluidic synthesis of advanced microparticles for encapsulation and controlled release
Duncanson, W. J., Lin, T., Abate, A. R., Seiffert, S., Shah, R. K., & Weitz, D. A. (2012) · Lab on a Chip · doi:10.1039/c2lc21164e · Cited by 370 · cited 1×
“The three-dimensional (3-D) geometry of the glass capillary devices offers a controlled production of double emulsions [61,130].”
BackgroundAn Axisymmetric Flow‐Focusing Microfluidic Device
Takeuchi, S., Garstecki, P., Weibel, D. B., & Whitesides, G. M. (2005) · Advanced Materials · doi:10.1002/adma.200401738 · Cited by 370 · cited 2×
“This is important to protect the fragile shell in the early interfacial polymerization stage from being disrupted [126] and for preventing wetting of the channels by the middle phase.”
BackgroundDouble Emulsion Templated Monodisperse Phospholipid Vesicles
Shum, H. C., Lee, D., Yoon, I., Kodger, T., & Weitz, D. A. (2008) · Langmuir · doi:10.1021/la801833a · Cited by 362 · cited 2×
“To make W/O/W emulsion, a water-soluble surfactant such as polyvinyl alcohol (PVA) [101,115,124], sodium dodecyl sulfate (SDS) [70,81,118], Pluronic [8,61] or Tween [9,127] is added in the outer aqueous phase and an oil-soluble surfactant is added in the middle oil phase, such as phospholipids [132], di-block copolyme…”
MethodDripping, Jetting, Drops, and Wetting: The Magic of Microfluidics
Utada, A. S., Chu, L.-Y., Fernandez-Nieves, A., Link, D. R., Holtze, C., & Weitz, D. A. (2007) · MRS Bulletin · doi:10.1557/mrs2007.145 · Cited by 358 · cited 2×
“There are two types of jetting, narrowing and widening [95].”
BackgroundNovel microreactors for functional polymer beads
Nisisako, T., Torii, T., & Higuchi, T. (2004) · Chemical Engineering Journal · doi:10.1016/j.cej.2003.11.019 · Cited by 346 · cited 3×
“The two dispersed phases could be a photopolymerizable phase and a nonphotopolymerizable phase (silicon oil) [155], two differently coloured monomer streams containing white and black pigments [152,156], two pre-polymer solutions with and without fluorescently labelled molecules [64], and two pre-polymer streams with…”
BackgroundControlled formulation of monodisperse double emulsions in a multiple-phase microfluidic system
Nisisako, T., Okushima, S., & Torii, T. (2005) · Soft Matter · doi:10.1039/b501972a · Cited by 335 · cited 13×
“A series of two T-junctions [52,70,110], two flow-focusing units [76,111,112], two cross junctions [113–115], ad one T-junction combi ed with one flo -focusing”
BackgroundMethodInfluentialPaik, P., Pamula, V. K., Pollack, M. G., & Fair, R. B. (2003) · Lab on a Chip · doi:10.1039/b210825a · Cited by 327
Putting Electrowetting to Work
Wheeler, A. R. (2008) · Science · doi:10.1126/science.1165719 · Cited by 315
Industrial lab-on-a-chip: Design, applications and scale-up for drug discovery and delivery
Vladisavljević, G. T., Khalid, N., Neves, M. A., Kuroiwa, T., Nakajima, M., Uemura, K., Ichikawa, S., & Kobayashi, I. (2013) · Advanced Drug Delivery Reviews · doi:10.1016/j.addr.2013.07.017 · Cited by 313
Self-citationDroplet‐Based Microreactors for the Synthesis of Magnetic Iron Oxide Nanoparticles
Frenz, L., El Harrak, A., Pauly, M., Bégin‐Colin, S., Griffiths, A. D., & Baret, J. (2008) · Angewandte Chemie International Edition · doi:10.1002/anie.200801360 · Cited by 313
Dual Nature of Improper Ferroelectricity in a Magnetoelectric Multiferroic
Picozzi, S., Yamauchi, K., Sanyal, B., Sergienko, I. A., & Dagotto, E. (2007) · Physical Review Letters · doi:10.1103/physrevlett.99.227201 · Cited by 311 · cited 2×
“In the co-flow geometry, the dispersed phase is delivered through the tapered injection tube and the continuous phase is introduced from the same direction through the coaxial area between the square capillary and the injection capillary tube [135,136].”
BackgroundMethodHigh‐Order Multiple Emulsions Formed in Poly(dimethylsiloxane) Microfluidics
Abate, A. R., & Weitz, D. A. (2009) · Small · doi:10.1002/smll.200900569 · Cited by 311 · cited 4×
“(a) Double emulsion; (b) Triple emulsion; (c) Quadruple emulsion [15]; (d) Quintuple emulsion [15]; (e) Janus drop [64]; (f) Ternary drop [16,17]; (g) Janus core; (h) Janus shell [65]; (i) Drop with controlled number of inner drops [54]; (j) Drop with controlled number of distinct inner drops [66]; (k) High-order emul…”
BackgroundMethodInfluentialFabrication of Monodisperse Gel Shells and Functional Microgels in Microfluidic Devices
Kim, J., Utada, A. S., Fernández‐Nieves, A., Hu, Z., & Weitz, D. A. (2007) · Angewandte Chemie International Edition · doi:10.1002/anie.200604206 · Cited by 307 · cited 1×
“The generated double emulsion drops were also used as templates for fabrication of termoresponsive poly(N-isopropylacrylamide) microshells [139] and non-spherical giant vesicles (colloidosomes and polymersomes) with multiple compartments [101].”
MethodDatta, S. S., Abbaspourrad, A., Amstad, E., Fan, J., Kim, S., Romanowsky, M. B., Shum, H. C., Sun, B., Utada, A. S., Windbergs, M., et al. (2014) · Advanced Materials · doi:10.1002/adma.201305119 · Cited by 302 · cited 2×
“Micron-sized double emulsions drops with ultra-thin shells are very useful templates for the preparation of functional vesicles and capsules with solid shells [142].”
BackgroundElectrocoalescence of drops synchronized by size-dependent flow in microfluidic channels
Ahn, K., Agresti, J., Chong, H., Marquez, M., & Weitz, D. A. (2006) · Applied Physics Letters · doi:10.1063/1.2218058 · Cited by 300
High throughput production of single core double emulsions in a parallelized microfluidic device
Romanowsky, M. B., Abate, A. R., Rotem, A., Holtze, C., & Weitz, D. A. (2012) · Lab on a Chip · doi:10.1039/c2lc21033a · Cited by 292 · cited 3×
“[60] fabricated a parallelized system incorporating up to 15 double drop makers in a 2D or 3D array network, capable of producing over 1 kg per day of core/shell drops using one-step emulsification method and with droplet size variation less than 6%.”
BackgroundMethodNovel cosmetic delivery systems: an application update
Patravale, V. B., & Mandawgade, S. D. (2008) · International Journal of Cosmetic Science · doi:10.1111/j.1468-2494.2008.00416.x · Cited by 280
Multicompartment Polymersomes from Double Emulsions
Shum, H. C., Zhao, Y., Kim, S., & Weitz, D. A. (2011) · Angewandte Chemie International Edition · doi:10.1002/anie.201006023 · Cited by 280 · cited 4×
“The generated double emulsions were used for the preparation of multi-compartment polymersomes [121] and solid lipid capsules [143].”
MethodInfluentialMicrofluidic Assembly of Homogeneous and Janus Colloid-Filled Hydrogel Granules
Shepherd, R. F., Conrad, J. C., Rhodes, S. K., Link, D. R., Marquez, M., Weitz, D. A., & Lewis, J. A. (2006) · Langmuir · doi:10.1021/la060759+ · Cited by 273 · cited 1×
“Janus droplets produced in microfluidic devices are used as templates for the production of Janus particles that contain two sides with different properties [17,152,153].”
MethodMicrofluidic Generation of Multifunctional Quantum Dot Barcode Particles
Zhao, Y., Shum, H. C., Chen, H., Adams, L. L. A., Gu, Z., & Weitz, D. A. (2011) · Journal of the American Chemical Society · doi:10.1021/ja200729w · Cited by 264 · cited 2×
“Double emulsions with two separate inner drops composed of quantum dots (QD)-tagged ethoxylated trimethylolpropane triacrylate (ETPTA) and ferric oxide containing ETPTA were produced using a double-bore injection capillary [146].”
BackgroundMethodMicrofluidic consecutive flow-focusing droplet generators
Seo, M., Paquet, C., Nie, Z., Xu, S., & Kumacheva, E. (2007) · Soft Matter · doi:10.1039/b700687j · Cited by 263 · cited 9×
“A series of two T-junctions [52,70,110], two flow-focusing units [76,111,112], two cross junctions [113–115], ad one T-junction combi ed with one flo -focusing”
BackgroundMethodInfluentialDouble-emulsion drops with ultra-thin shells for capsule templates
Kim, S.-H., Kim, J. W., Cho, J.-C., & Weitz, D. A. (2011) · Lab Chip · doi:10.1039/c1lc20434c · Cited by 259 · cited 4×
“Glass capillary evice with wo coaxial injection capillaries was used for the formation of core/shell drops with ultrathin shells [31], Figure 16.”
BackgroundMethodInfluentialMultiple Polymersomes for Programmed Release of Multiple Components
Kim, S.-H., Shum, H. C., Kim, J. W., Cho, J.-C., & Weitz, D. A. (2011) · Journal of the American Chemical Society · doi:10.1021/ja205687k · Cited by 250 · cited 2×
“The inner drops then merge to form gas bubbles inside the outer drops [147].”
BackgroundOn the stability of ascorbic acid in emulsified systems for topical and cosmetic use
Gallarate, M., Carlotti, M. E., Trotta, M., & Bovo, S. (1999) · International Journal of Pharmaceutics · doi:10.1016/s0378-5173(99)00228-8 · Cited by 249 · cited 1×
“Emulsions are dispersion of stabilised liquids within a continuous immiscible liquid, and has long been used in a verity of applications including production of pharmaceuticals [1–3], cosmetics [4], foods [5], electronics [6], and energy-related [7–10].”
BackgroundMicrofluidic production of multiple emulsions and functional microcapsules
Lee, T. Y., Choi, T. M., Shim, T. S., Frijns, R. A. M., & Kim, S.-H. (2016) · Lab on a Chip · doi:10.1039/c6lc00809g · Cited by 247
Formation of simple and compound drops in microfluidic devices
Zhou, C., Yue, P., & Feng, J. J. (2006) · Physics of Fluids · doi:10.1063/1.2353116 · Cited by 244
“On the Fly” Continuous Generation of Alginate Fibers Using a Microfluidic Device
Shin, S.-J., Park, J.-Y., Lee, J.-Y., Park, H., Park, Y.-D., Lee, K.-B., Whang, C.-M., & Lee, S.-H. (2007) · Langmuir · doi:10.1021/la700818q · Cited by 239 · cited 1×
“Microfluidic strategies provide an easy and cheap alternative for making uniform microfibers with higher tensile strength than other methods [166,167].”
BackgroundControllable microfluidic production of multicomponent multiple emulsions
Wang, W., Xie, R., Ju, X.-J., Luo, T., Liu, L., Weitz, D. A., & Chu, L.-Y. (2011) · Lab on a Chip · doi:10.1039/c1lc20065h · Cited by 232 · cited 6×
“The generated quintuple-component O/W/O/W triple emulsion consists of the red and white innermost oil droplets of F1-1 and F1-2, dispersed in an aqueous phase, which is a mixture of F2-1, F2-2, and F2-c phases, surrounded by an oil layer of F3-M and the whole drop is dispersed in the continuous aqueous phase (F4-M).”
BackgroundMethodInfluentialBauer, W.-A. C., Fischlechner, M., Abell, C., & Huck, W. T. S. (2010) · Lab on a Chip · doi:10.1039/c004046k · Cited by 227 · cited 1×
“PDMS devices with two flow focusing drop makers were used to prepare O/W/O [120,121], O/O/W [122], W/W/O [123] and W/O/W double emulsions in two emulsification steps [115,124,125].”
MethodRobust scalable high throughput production of monodisperse drops
Amstad, E., Chemama, M., Eggersdorfer, M., Arriaga, L. R., Brenner, M. P., & Weitz, D. A. (2016) · Lab on a Chip · doi:10.1039/c6lc01075j · Cited by 227
Mastrobattista, E., Taly, V., Chanudet, E., Treacy, P., Kelly, B. T., & Griffiths, A. D. (2005) · Chemistry & Biology · doi:10.1016/j.chembiol.2005.09.016 · Cited by 222
Encapsulated liquid sorbents for carbon dioxide capture
Vericella, J. J., Baker, S. E., Stolaroff, J. K., Duoss, E. B., Hardin, J. O., Lewicki, J., Glogowski, E., Floyd, W. C., Valdez, C. A., Smith, W. L., et al. (2015) · Nature Communications · doi:10.1038/ncomms7124 · Cited by 213 · cited 2×
“To make W/O/W emulsion, a water-soluble surfactant such as polyvinyl alcohol (PVA) [101,115,124], sodium dodecyl sulfate (SDS) [70,81,118], Pluronic [8,61] or Tween [9,127] is added in the outer aqueous phase and an oil-soluble surfactant is added in the middle oil phase, such as phospholipids [132], di-block copolyme…”
MethodLagus, T. P., & Edd, J. F. (2013) · Journal of Physics D: Applied Physics · doi:10.1088/0022-3727/46/11/114005 · Cited by 213 · cited 1×
“The drop formation mechanism in each regime is different and governed by interaction of several forces, such as interfacial, viscous, inertial and gravitational [93].”
BackgroundSmart Microgel Capsules from Macromolecular Precursors
Seiffert, S., Thiele, J., Abate, A. R., & Weitz, D. A. (2010) · Journal of the American Chemical Society · doi:10.1021/ja102156h · Cited by 206
Miniaturizing chemistry and biology in microdroplets
Kelly, B. T., Baret, J.-C., Taly, V., & Griffiths, A. D. (2007) · Chemical Communications · doi:10.1039/b616252e · Cited by 197 · cited 1×
“Electric control of droplets in microfluidic channels is a robust approach that can be used to actively control droplet splitting [179–184], merging [179,184–191], and sorting [179,192], which are of great interest in droplet-reaction systems, high-throughput screening, and combinatorial chemistry.”
MethodControllable Preparation of Monodisperse O/W and W/O Emulsions in the Same Microfluidic Device
Xu, J. H., Li, S. W., Tan, J., Wang, Y. J., & Luo, G. S. (2006) · Langmuir · doi:10.1021/la0605743 · Cited by 196
Grigoriev, D. O., Букреева, Т. В., Möhwald, H., & Shchukin, D. G. (2007) · Langmuir · doi:10.1021/la702873f · Cited by 189
Recent advances in microfluidic production of Janus droplets and particles
Nisisako, T. (2016) · Current Opinion in Colloid & Interface Science · doi:10.1016/j.cocis.2016.05.003 · Cited by 177 · cited 2×
“Typically, a Y-shaped channel was used to form a two-phase flow of two miscible dispersed phases, which then entered the sheath flow of the continuous phase in the downstream cross-junction to form biphasic Janus drops, Figure 27 [154].”
MethodNisisako, T., Ando, T., & Hatsuzawa, T. (2012) · Lab on a Chip · doi:10.1039/c2lc40245a · Cited by 172 · cited 1×
“The fluids from vertical, radially arranged, inlet channels are supplied to individual drop makers through coaxial annular channels fabricated on the chip surface [197].”
BackgroundFaster multiple emulsification with drop splitting
Abate, A. R., & Weitz, D. A. (2011) · Lab on a Chip · doi:10.1039/c0lc00706d · Cited by 168 · cited 1×
“Small multiple emulsion droplets were generated at a faster rate by splitting large multiple emulsion drops into two identical drops which were further divided in a series of even smaller drops using Y-shaped channels [201].”
BackgroundEquilibrium and Nonequilibrium States in Microfluidic Double Emulsions
Pannacci, N., Bruus, H., Bartolo, D., Etchart, I., Lockhart, T., Hennequin, Y., Willaime, H., & Tabeling, P. (2008) · Physical Review Letters · doi:10.1103/physrevlett.101.164502 · Cited by 160 · cited 1×
“PDMS devices with two flow focusing drop makers were used to prepare O/W/O [120,121], O/O/W [122], W/W/O [123] and W/O/W double emulsions in two emulsification steps [115,124,125].”
MethodMultiple modular microfluidic (M3) reactors for the synthesis of polymer particles
Li, W., Greener, J., Voicu, D., & Kumacheva, E. (2009) · Lab on a Chip · doi:10.1039/b906626h · Cited by 159 · cited 1×
“The most common geometries of distribution channel network are ladder-like [200,205] and tree-like branched geometry [206,207].”
BackgroundCheng, Y., Yu, Y., Fu, F., Wang, J., Shang, L., Gu, Z., & Zhao, Y. (2016) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.5b11445 · Cited by 158 · cited 1×
“Janus microfibers with different number of hallow channels were fabricated by generating multiple laminar flows using multi-bore capillary microfluidics [175].”
MethodLi, F., Wang, X., & Wu, D. (2015) · Energy Conversion and Management · doi:10.1016/j.enconman.2015.10.026 · Cited by 158
One‐Step Emulsification of Multiple Concentric Shells with Capillary Microfluidic Devices
Kim, S., & Weitz, D. A. (2011) · Angewandte Chemie International Edition · doi:10.1002/anie.201102946 · Cited by 158 · cited 5×
“One additional small capillary (not shown here) is placed between the injection and outer capillary [151].”
BackgroundMethodInfluentialConchouso, D., Castro, D., Khan, S. A., & Foulds, I. G. (2014) · Lab on a Chip · doi:10.1039/c4lc00379a · Cited by 157 · cited 1×
“The most common geometries of distribution channel network are ladder-like [200,205] and tree-like branched geometry [206,207].”
BackgroundMultifunctional photonic crystal barcodes from microfluidics
Zhao, Y., Xie, Z., Gu, H., Jin, L., Zhao, X., Wang, B., & Gu, Z. (2012) · NPG Asia Materials · doi:10.1038/am.2012.46 · Cited by 155 · cited 3×
“The injection tube has five bores, which allows four different oil phases indicated in different colours and one aqueous phase in the middle to be injected separately [66].”
BackgroundMethodRose, R. D., Zelikin, A. N., Johnston, A. P. R., Sexton, A. L., Chong, S., Cortez‐Jugo, C., Mulholland, W. J., Caruso, F., & Kent, S. J. (2008) · Advanced Materials · doi:10.1002/adma.200801826 · Cited by 154
Microfluidic fabrication of water-in-water (w/w) jets and emulsions
Shum, H. C., Varnell, J. A., & Weitz, D. A. (2012) · Biomicrofluidics · doi:10.1063/1.3670365 · Cited by 150
Kilo-scale droplet generation in three-dimensional monolithic elastomer device (3D MED)
Jeong, H., Yelleswarapu, V. R., Yadavali, S., Issadore, D., & Lee, D. (2015) · Lab on a Chip · doi:10.1039/c5lc01025j · Cited by 149 · cited 2×
“Possible scaling-up approaches are parallelization of drop makers [199,200] and/or drop splitting [201–204].”
BackgroundMicrofluidics-Produced Collagen Fibers Show Extraordinary Mechanical Properties
Haynl, C., Hofmann, E., Pawar, K., Förster, S., & Scheibel, T. (2016) · Nano Letters · doi:10.1021/acs.nanolett.6b02828 · Cited by 146 · cited 1×
“Collagen microfibers were fabricated using a PDMS microfluidic chip with a cross junction [174].”
MethodGong, X., Peng, S., Wen, W., Sheng, P., & Li, W. (2008) · Advanced Functional Materials · doi:10.1002/adfm.200801315 · Cited by 131 · cited 1×
“The same device was used to generate core/shell drops consisting of aqueous aspirin solution in the core and aqueous solution of high molecular weight chitosan loaded with F3O4 nanoparticles in the shell [117].”
MethodLarge-scale droplet production in microfluidic devices—an industrial perspective
Holtze, C. (2013) · Journal of Physics D: Applied Physics · doi:10.1088/0022-3727/46/11/114008 · Cited by 127 · cited 1×
“The scale up the drop production, many drop makers should be joined together with the least possible number of pumps/pressure vessels and a suitable network of distribution and collection channels [194].”
BackgroundSingle step emulsification for the generation of multi-component double emulsions
Adams, L., Kodger, T. E., Kim, S., Shum, H. C., Franke, T., & Weitz, D. A. (2012) · Soft Matter · doi:10.1039/c2sm25953b · Cited by 127 · cited 6×
“The hydrophobic treatment can be achieved by dipping the capillary into 5% (v/v) OTMS solution in toluene [78] and evaporating the solvent or by exposing the capillary to OTMS vapour inside the oven at 130 ◦C for 15 min [79].”
BackgroundMethodInfluentialKim, H. K., & Park, T. G. (2004) · Journal of Controlled Release · doi:10.1016/j.jconrel.2004.04.020 · Cited by 120
He, X., Wang, W., Liu, Y.-M., Jiang, M., Wu, F., Deng, K., Liu, Z., Ju, X., Xie, R., & Chu, L. (2015) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.5b05075 · Cited by 113
Thiele, J., Abate, A. R., Shum, H. C., Bachtler, S., Förster, S., & Weitz, D. A. (2010) · Small · doi:10.1002/smll.201000798 · Cited by 110 · cited 8×
“Drop maker arrays based on cross j nction flo focusing geometry used to produce double emulsion droplets using two separate inlets for the iddle phase [115].”
BackgroundMethodInfluentialZhang, M., Wang, W., Xie, R., Ju, X., Liu, L., Gu, Y.-Y., & Chu, L. (2013) · Soft Matter · doi:10.1039/c3sm00066d · Cited by 107
Recent developments in scale-up of microfluidic emulsion generation via parallelization
Jeong, H., Issadore, D., & Lee, D. (2016) · Korean Journal of Chemical Engineering · doi:10.1007/s11814-016-0041-6 · Cited by 106 · cited 1×
“, only one inlet port is used to deliver one type of fluid to all drop makers [203].”
MethodScaling the drop size in coflow experiments
Castro-Hernández, E., Gundabala, V. R., Fernández‐Nieves, A., & Gordillo, J. M. (2009) · New Journal of Physics · doi:10.1088/1367-2630/11/7/075021 · Cited by 103 · cited 1×
“The widening shape of the inertial-driven jet is associated to the shearing force exerted by the outer phase which tends to decelerate the jet [97].”
BackgroundPessi, J., Santos, H. A., Miroshnyk, I., JoukoYliruusi, Weitz, D. A., & Mirza, S. (2014) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2014.06.012 · Cited by 101
Huang, S., Tan, W.-H., Tseng, F., & Takeuchi, S. (2006) · Journal of Micromechanics and Microengineering · doi:10.1088/0960-1317/16/11/013 · Cited by 98 · cited 2×
“To make W/O/W emulsion, a water-soluble surfactant such as polyvinyl alcohol (PVA) [101,115,124], sodium dodecyl sulfate (SDS) [70,81,118], Pluronic [8,61] or Tween [9,127] is added in the outer aqueous phase and an oil-soluble surfactant is added in the middle oil phase, such as phospholipids [132], di-block copolyme…”
MethodEmulsion-based techniques for encapsulation in biomedicine, food and personal care
Kakran, M., & Antipina, M. N. (2014) · Current Opinion in Pharmacology · doi:10.1016/j.coph.2014.09.003 · Cited by 95 · cited 1×
“Bulk mixing is associated with random shear distribution, and leads to the broad droplet size distribution in each step [38,39].”
BackgroundRecent advances in multiple emulsions and their application as templates
Silva, B. F. B., Rodríguez‐Abreu, C., & Vilanova, N. (2016) · Current Opinion in Colloid & Interface Science · doi:10.1016/j.cocis.2016.07.006 · Cited by 95
Ekanem, E. E., Nabavi, S. A., Vladisavljević, G. T., & Gu, S. (2015) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.5b06943 · Cited by 93 · cited 5×
“The hydrophobic treatment can be achieved by dipping the capillary into 5% (v/v) OTMS solution in toluene [78] and evaporating the solvent or by exposing the capillary to OTMS vapour inside the oven at 130 ◦C for 15 min [79].”
BackgroundMethodInfluentialSelf-citationLin, Y., Huang, K., Yang, C., Wang, C., Yang, Y., Hsu, H., Liao, Y.-J., & Tsai, C. (2012) · PLoS ONE · doi:10.1371/journal.pone.0033184 · Cited by 87 · cited 2×
“Planar flow focusing devices [168–170] and glass capillary devices [170–173] have been used for the production of microfibers, such as alginate microfibers for the controlled release of drug in response to magnetic field and for cell culture [169] (Figure 29).”
BackgroundMethodFormation of Droplets and Bubbles in Microfluidic Systems
Garstecki, P. (2010) · NATO science for peace and security series. A, Chemistry and biology · doi:10.1007/978-90-481-9029-4_9 · Cited by 87
Lee, D., & Yang, S. H. (2011) · Sensors and Actuators B Chemical · doi:10.1016/j.snb.2011.12.017 · Cited by 86 · cited 1×
“This modification of the PDMS surface was found to be stable for 28 days [75].”
BackgroundNovel Parallel Integration of Microfluidic Device Network for Emulsion Formation
Tetradis-Meris, G., Rossetti, D., de Torres, C. P., Cao, R., Lian, G., & Janes, R. (2009) · Industrial & Engineering Chemistry Research · doi:10.1021/ie900165b · Cited by 81 · cited 2×
“Furthermore, the tree structure is more affected by the variations in the size of the channels where a defect in one inlet or outlet will break the symmetry of the whole branch [195].”
BackgroundPatterning microfluidic device wettability with spatially-controlled plasma oxidation
Kim, S., Sukovich, D. J., & Abate, A. R. (2015) · Lab on a Chip · doi:10.1039/c5lc00626k · Cited by 80 · cited 2×
“A common method is using oxygen plasma to oxidize the PDMS surface [73], but the surface hydrophobicity is restored after several minutes to several hours [74], which makes PDMS devices difficult to use for applications that require stable hydrophilic surface property.”
MethodDouble emulsions from a capillary array injection microfluidic device
Shang, L., Cheng, Y., Wang, J., Ding, H., Rong, F., Zhao, Y., & Gu, Z. (2014) · Lab on a Chip · doi:10.1039/c4lc00698d · Cited by 74 · cited 3×
“W/O/W drops with shells thinner than 1 μm were produced using a flow focusing PDMS device with two junctions with different channel depths [143,144], Figure 15.”
BackgroundMethodOthman, R., Vladisavljević, G. T., & Nagy, Z. K. (2015) · Chemical Engineering Science · doi:10.1016/j.ces.2015.06.025 · Cited by 74 · cited 5×
“The hydrophobic treatment can be achieved by dipping the capillary into 5% (v/v) OTMS solution in toluene [78] and evaporating the solvent or by exposing the capillary to OTMS vapour inside the oven at 130 ◦C for 15 min [79].”
BackgroundMethodInfluentialSelf-citationHybrid soft-lithography/laser machined microchips for the parallel generation of droplets
Muluneh, M., & Issadore, D. (2013) · Lab on a Chip · doi:10.1039/c3lc50979f · Cited by 74 · cited 1×
“The most common geometries of distribution channel network are ladder-like [200,205] and tree-like branched geometry [206,207].”
BackgroundCeramic microparticles and capsules via microfluidic processing of a preceramic polymer
Ye, C., Chen, A., Colombo, P., & Martinez, C. J. (2010) · Journal of The Royal Society Interface · doi:10.1098/rsif.2010.0133.focus · Cited by 74
Herranz‐Blanco, B., Ginestar, E., Zhang, H., Hirvonen, J. J., & Santos, H. A. (2016) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2016.11.024 · Cited by 71
Microencapsulation of advanced solvents for carbon capture
Stolaroff, J. K., Ye, C., Oakdale, J. S., Baker, S. E., Smith, W. L., Nguyen, D. T., Spadaccini, C. M., & Aines, R. D. (2016) · Faraday Discussions · doi:10.1039/c6fd00049e · Cited by 69 · cited 1×
“The generated double emulsion drops can be used for encapsulation of carbon dioxide absorbents [137].”
MethodPlanar microfluidic drop splitting and merging
Collignon, S., Friend, J. R., & Yeo, L. Y. (2015) · Lab on a Chip · doi:10.1039/c4lc01453g · Cited by 69
Microfluidic generation of hollow Ca-alginate microfibers
Meng, Z., Wang, W., Xie, R., Ju, X., Liu, Z., & Chu, L. (2016) · Lab on a Chip · doi:10.1039/c6lc00640j · Cited by 68 · cited 2×
“A similar flow configuration was applied to produce a coaxial jet composed of four aqueous solutions (W1, W2, W3 and W4), that served as a template for hollow Ca-alginate microfibers [150].”
MethodDavies, R. T., Kim, D., & Park, J. (2012) · Journal of Micromechanics and Microengineering · doi:10.1088/0960-1317/22/5/055003 · Cited by 68
Controllable microfluidic strategies for fabricating microparticles using emulsions as templates
Zhang, M., Wang, W., Xie, R., Ju, X., Liu, Z., Lu, J., Chen, Q., & Chu, L. (2015) · Particuology · doi:10.1016/j.partic.2015.08.001 · Cited by 68 · cited 3×
“Different functional ingredients can be added independently and individually into both the inner and outer drops [56] during or after drop generation.”
BackgroundEisinaitė, V., Juraite, D., Schroën, K. G. P. H., & Leskauskaitė, D. (2016) · Food Chemistry · doi:10.1016/j.foodchem.2016.03.046 · Cited by 66
On-chip development of hydrogel microfibers from round to square/ribbon shape
Bai, Z., Reyes, J. M. M., Montazami, R., & Hashemi, N. N. (2014) · Journal of Materials Chemistry A · doi:10.1039/c3ta14573e · Cited by 65 · cited 1×
“Microfluidic strategies provide an easy and cheap alternative for making uniform microfibers with higher tensile strength than other methods [166,167].”
BackgroundKoga, K., Takarada, N., & Takada, K. (2009) · European Journal of Pharmaceutics and Biopharmaceutics · doi:10.1016/j.ejpb.2009.09.004 · Cited by 64
Computations of breakup modes in laminar compound liquid jets in a coflowing fluid
Vu, T. V., Homma, S., Tryggvason, G., Wells, J. C., & Takakura, H. (2012) · International Journal of Multiphase Flow · doi:10.1016/j.ijmultiphaseflow.2012.10.004 · Cited by 63 · cited 1×
“In addition, an increase in the interfacial tension favours the dripping mode; thus, a reduction in concentration of the stabilisers can supress the jetting modes [102,104,105].”
BackgroundFibrous poly(chitosan-g-dl-lactic acid) scaffolds prepared via electro-wet-spinning
Wan, Y., Cao, X., Zhang, S., Wang, S., & Wu, Q. (2008) · Acta Biomaterialia · doi:10.1016/j.actbio.2008.01.001 · Cited by 57 · cited 1×
“Common methods used for the fabrication of microfibers are self-assembly [162], wet spinning [163], electrospinning [161,164] and electro-wet spinning [165].”
MethodSimple and reusable off-the-shelf microfluidic devices for the versatile generation of droplets
Li, T., Zhao, L. Q., Liu, W., Xu, J., & Wang, J. (2016) · Lab on a Chip · doi:10.1039/c6lc00967k · Cited by 51 · cited 2×
“Recently, a reusable and low cost microfluidic device based on the assembly of commercial dispensing needles, mini-cross links and tree-links was introduced [141].”
BackgroundMethodMultiphase flow in lab on chip devices: A real tool for the future?
Shui, L., Pennathur, S., Eijkel, J. C. T., & van den Berg, A. (2008) · Lab on a Chip · doi:10.1039/b808974b · Cited by 48 · cited 1×
“, the drop diameter, is in the micrometre range (less than 1 mm) [94,95].”
BackgroundMicrofluidic wet-spinning of alginate microfibers: a theoretical analysis of fiber formation
Bonhomme, O., Leng, J., & Colin, A. (2012) · Soft Matter · doi:10.1039/c2sm25552a · Cited by 47
Park, D. Y., Mun, C. H., Kang, E., No, D. Y., Ju, J., & Lee, S. H. (2014) · Biofabrication · doi:10.1088/1758-5082/6/2/024108 · Cited by 44 · cited 1×
“[176], published by Institute of Physics, 2014.”
Semipermeable Elastic Microcapsules for Gas Capture and Sensing
Nabavi, S. A., Vladisavljević, G. T., Gu, S., & Manovic, V. M. (2016) · Langmuir · doi:10.1021/acs.langmuir.6b02420 · Cited by 42 · cited 2×
“To make W/O/W emulsion, a water-soluble surfactant such as polyvinyl alcohol (PVA) [101,115,124], sodium dodecyl sulfate (SDS) [70,81,118], Pluronic [8,61] or Tween [9,127] is added in the outer aqueous phase and an oil-soluble surfactant is added in the middle oil phase, such as phospholipids [132], di-block copolyme…”
MethodSelf-citationA 3D-printed microcapillary assembly for facile double emulsion generation
Martino, C., Berger, S., Wootton, R. C. R., & deMello, A. J. (2014) · Lab on a Chip · doi:10.1039/c4lc00992d · Cited by 41
Vesicle budding from polymersomes templated by microfluidically prepared double emulsions
Thiele, J., Chokkalingam, V., Ma, S., Wilson, D. A., & Huck, W. T. S. (2013) · Materials Horizons · doi:10.1039/c3mh00043e · Cited by 39 · cited 2×
“PDMS devices with two flow focusing drop makers were used to prepare O/W/O [120,121], O/O/W [122], W/W/O [123] and W/O/W double emulsions in two emulsification steps [115,124,125].”
MethodNabavi, S. A., Vladisavljević, G. T., Eguagie, E. M., Li, B., Georgiadou, S., & Manovic, V. M. (2016) · Chemical Engineering Journal · doi:10.1016/j.cej.2016.07.054 · Cited by 37
Self-citationAssembly of emulsion droplets into fibers by microfluidic wet spinning
Bell, R. V., Parkins, C. C., Young, R. A., Preuss, C. M., Stevens, M. M., & Bon, S. A. F. (2015) · Journal of Materials Chemistry A · doi:10.1039/c5ta08917d · Cited by 34
Akamatsu, K., Kanasugi, S., Nakao, S., et al. (2015) · Langmuir · doi:10.1021/acs.langmuir.5b01514 · Cited by 32 · cited 3×
“The membrane is placed between the two Luer–Stub adapters [178].”
BackgroundMethodInfluentialLong-term in vitro study of paclitaxel-eluting bioresorbable core/shell fiber structures
Kraitzer, A., Ofek, L., Schreiber, R., & Zilberman, M. (2007) · Journal of Controlled Release · doi:10.1016/j.jconrel.2007.11.011 · Cited by 30 · cited 1×
“Microfibers can act as high surface area micro-carriers for obtaining the controlled zero-order release profile of water soluble drugs with low efficiency of encapsulation [160,161].”
BackgroundTrujillo-Cayado, L. A., Santos, J., Alfaro, M. C., et al. (2016) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.6b01320 · Cited by 29
Flexible Asymmetric Encapsulation for Dehydration‐Responsive Hybrid Microfibers
Chaurasia, A. S., & Sajjadi, S. (2016) · Small · doi:10.1002/smll.201600465 · Cited by 29
Millimetric core–shell drops via buoyancy assisted non-confined microfluidics
Chaurasia, A. S., & Sajjadi, S. (2015) · Chemical Engineering Science · doi:10.1016/j.ces.2015.02.028 · Cited by 25 · cited 3×
“Both tips had the same vertical position for fabricating core/shell drops, whereas the inner tip was kept behind the outer tip for double emulsion drops with multiple inner drops [140].”
BackgroundMethodMicrofluidic production of hyaluronic acid derivative microfibers to control drug release
Agnello, S., Gasperini, L., Reis, R. L., Mano, J. F., Pitarresi, G. L., Palumbo, F. S., & Giammona, G. (2016) · Materials Letters · doi:10.1016/j.matlet.2016.07.014 · Cited by 23
Byun, A., Shim, J., Han, S. W., Kim, B., Chae, P. S., Shin, H. S., & Kim, J. W. (2015) · Chemical Communications · doi:10.1039/c5cc04547a · Cited by 23 · cited 1×
“O/W/O double emulsions are also formed using the same device with the opposite capillary surface treatment [138].”
MethodNaito, T., Nakamura, M., Kaji, N., Kubo, T., Baba, Y., & Otsuka, K. (2016) · Micromachines · doi:10.3390/mi7050082 · Cited by 12
Cited by
Moragues, T., Arguijo, D., Beneyton, T., Modavi, C., Simutis, K., Abate, A. R., Baret, J.-C., deMello, A. J., Densmore, D., & Griffiths, A. D. (2023) · Nature Reviews Methods Primers · doi:10.1038/s43586-023-00212-3 · Cited by 316
Metadata
- Authors
- Vladisavljević, G., Al Nuumani, R., & Nabavi, S.
- Venue
- Micromachines
- Publisher
- MDPI AG
- Published
- 2017-03-02
- Volume
- 8
- Issue
- 3
- Pages
- 75
- ISSN
- 2072-666X (ISSN-L)
- OpenAlex
- W2592233253
- Cited by
- 170
- References
- 133
- FWCI
- 5.94
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.