Synthesis and Biological Application of Polylactic Acid
Open accessThe DOI matches its Crossref record; 140 of the 140 references it cites were found in a registry or an index; 9 of the 125 sources its claims cite were checked for support.
Abstract
Over the past few decades, with the development of science and technology, the field of biomedicine has rapidly developed, especially with respect to biomedical materials. Low toxicity and good biocompatibility have always been key targets in the development and application of biomedical materials. As a degradable and environmentally friendly polymer, polylactic acid, also known as polylactide, is favored by researchers and has been used as a commercial material in various studies. Lactic acid, as a synthetic raw material of polylactic acid, can only be obtained by sugar fermentation. Good biocompatibility and biodegradability have led it to be approved by the U.S. Food and Drug Administration (FDA) as a biomedical material. Polylactic acid has good physical properties, and its modification can optimize its properties to a certain extent. Polylactic acid blocks and blends play significant roles in drug delivery, implants, and tissue engineering to great effect. This article describes the synthesis of polylactic acid (PLA) and its raw materials, physical properties, degradation, modification, and applications in the field of biomedicine. It aims to contribute to the important knowledge and development of PLA in biomedical applications.
Overview
CoChat Summary
TL;DR
This review summarizes polylactic acid (PLA) synthesis, physical properties, degradation, modification, and biomedical applications. It highlights PLA’s biocompatibility and biodegradability while noting challenges in mechanical properties, nanoparticle drug-delivery commercialization, and production cost.
Key findings
- PLA is a biodegradable, biocompatible polymer approved by the FDA for biomedical use; it is made from lactic acid, which is traditionally obtained by sugar fermentation, and exists as PLLA, PDLA, and PDLLA.
- Key properties include processing temperatures of 170–230 °C; PLLA and PDLA melting points of 207 °C; racemic crystals with a melting point of 230 °C and ultimate tensile strength of 50 MPa; a glass transition temperature of 55 °C for PLA of 22,000 g mol−1; and a heat of fusion of 93.7 J g−1 for 100% pure crystals.
- Modification by copolymerization, blending, plasticizers, or crosslinking can improve PLA’s hydrophobicity, toughness, and degradation; examples include PLA–PEG hemoglobin microcapsules reaching a 90% embedding rate versus 7.9% for PLA alone, a PLA–naltrexone complex with 67% in vitro release at 35 days, and PLA–PEG–PLA paclitaxel microspheres with 49% release in one month.
- Biomedical applications include tissue engineering, drug delivery, and implants; PLA-based stents are commercialized, and 3D-printed PLA scaffolds are reported to cause less inflammation, but no PLA nanoparticle has been successfully marketed for drug delivery.
Methods
- Narrative review of PLA synthesis, raw materials, physical properties, degradation, modification, and biomedical applications; no primary experimental data, sample, or systematic search strategy is described.
- Main analysis is qualitative synthesis of cited literature and selected examples, with no meta-analysis or statistical pooling.
Limitations
- The paper states that PLA suffers from brittleness, poor mechanical properties, slow crystallization speed, and low crystallinity; it also states that drug-delivery nanoparticles face challenges including side effects, toxicity, size/position/shape issues, positive-charge cytotoxicity, oxidative stress, DNA damage, ROS-related inflammation, hemolysis risk, complex disease microenvironments, and blood interactions, and that commercialization is limited by price and raw-material production efficiency.
- Evident from the text: as a narrative review, it lacks systematic search/inclusion criteria and quantitative synthesis, and many claims rely on cited secondary literature without new experimental validation.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures

![Figure 2 Synthesis of polylactic acid (PLA) from l- and d-lactic acids [28]. Adapted from Auras et al. by permission of Wiley–VCH Verlag GmbH & Co. KGaA.](https://figures.cochat.ai/paper-figures/c0c15b60797046e2a98a260168f15ebf/synthesis-and-biological-application-of-polylactic-acid-figure-2.jpg)

![Figure 4 High drug loading and pH-responsivity PLA-g-doxorubicin (DOX) nanoparticles [99]. Reprinted from Cheng with permission from Express Polymer Letters.](https://figures.cochat.ai/paper-figures/f2964f7b6801471a93511477c2ba67d7/synthesis-and-biological-application-of-polylactic-acid-figure-4.jpg)
![Figure 5 Schematic illustration of the concept of stereocomplex hydrogel formed by mixing aqueous solutions of bio-polymers containing enantiomeric oligo(lactic acid) [125]. Reprinted from Nostrum with permission from Express Polymer Letters.](https://figures.cochat.ai/paper-figures/7afa96ad62934c7c95f90c9477ca9c3d/synthesis-and-biological-application-of-polylactic-acid-figure-5.jpg)
Verification
Claims the paper makes
4 Valid · 0 Not valid · 64 Not checked · 10 Own results and interpretations
None of the sources cited for this claim have been checked yet.
In the paper
“The degree of crystallinity affects the degradation of PLA [52,53].”
§ Synthesis and Biological Application of Polylactic Acid > 2. PLA Synthesis and Properties > 2.3. PLA Properties
What the sources say
- Could not verifycites [52] Li H. Huneault M.A. Effect of nucleation and plasticization on the crystallization of poly (lactic acid) Polymer 2007 48 6855 6866 10.1016/j.polymer.2007.09.020 sourceExperimental — accuracy not yet measured
The Introduction mentions PLA’s compostability, while §3.4 examines crystallinity during molding and §3.6 examines thermal resistance. None of these passages addresses whether the degree of crystallinity affects PLA degradation; searches for degradation, biodegradation, and hydrolysis found no passage establishing that relationship. Page numbers were not available in our copy. (LLM, conf=0.74)
- Not checked yetcites [53] Liu H. Zhang J. Research Progress in Toughening Modification of Poly (lactic acid) J. Polym. Sci. Part B-Polym. Phys. 2011 49 1051 1083 10.1002/polb.22283 source
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Could not verify
None of the sources cited for this claim have been checked yet.
In the paper
“Su et al. found that, when polylactic acid was used as the membrane material, the embedding rate of hemoglobin was very low, only 7.9%.”
§ Synthesis and Biological Application of Polylactic Acid > 3. Application > 3.1. Tissue Engineering
What the sources say
- Not checked yetcites [87] Waring M.J. Arrowsmith J. Leach A.R. Leeson P.D. Mandrell S. Owen R.M. Pairaudeau G. Pennie W.D. Pickett S.D. Wang J. An analysis of the attrition of drug candidates from four major pharmaceutical companies Nat. Rev. Drug Discov. 2015 14 475 486 10.1038/nrd4609 26091267 source
- Not checked yetcites [88] Langer R. Vacanti J.P. Tissue engineering Science 1993 260 920 926 10.1126/science.8493529 8493529 source
- Could not verifycites [89] Zhang Y. Sophocleous A.M. Schwendeman S.P. Inhibition of Peptide Acylation in PLGA Microspheres with Water-soluble Divalent Cationic Salts Pharm. Res. 2009 26 1986 1994 10.1007/s11095-009-9914-2 19533307 PMC4260456 sourceExperimental — accuracy not yet measured
Our copy of Zhang et al. (2009) is entirely about octreotide acetate encapsulated in PLGA/PLA microspheres and the inhibition of peptide acylation by water-soluble divalent cationic salts (CaCl2, MnCl2); no passage mentions hemoglobin, a 'Su et al.' work, polylactic acid used as a membrane material, or a 7.9% embedding/encapsulation figure (searched: hemoglobin, Su et al. / 7.9%, encapsulation efficiency and protein loading, poly(lactic acid) membrane). The MATERIAL AND METHODS section ('Drug loading and encapsulation efficiency') reports only octreotide extraction/HPLC assay of microspheres, and the reference list contains no Su entry, so nothing in our copy either supports or contradicts the attributed finding. The decisive part is simply absent from this paper, so the claim cannot be judged against it. (LLM, conf=0.75)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Good biocompatibility also ensures that there is no inflammatory reaction in the surrounding tissue due to rejection after it enters the human body [75,76,77].”
§ Synthesis and Biological Application of Polylactic Acid > 3. Application
What the sources say
- Partly supportedcites [75] Mitragotri S. Burke P.A. Langer R. Overcoming the challenges in administering biopharmaceuticals: Formulation and delivery strategies Nat. Rev. Drug Discov. 2014 13 655 672 10.1038/nrd4363 25103255 PMC4455970 sourceExperimental — accuracy not yet measured
The Microparticles section describes PLGA as biocompatible and says it degrades into toxicologically acceptable products. It does not make that claim specifically for PLA or say that biocompatibility ensures no inflammatory reaction or tissue rejection after implantation. (LLM, conf=0.85)
- Partly supportedcites [76] Nottelet B. Darcos V. Coudane J. Aliphatic polyesters for medical imaging and theranostic applications Eur. J. Pharm. Biopharm. 2015 97 350 370 10.1016/j.ejpb.2015.06.023 26614557 sourceExperimental — accuracy not yet measured
The Introduction (page unavailable) describes aliphatic polyesters as having demonstrated biocompatibility, which supports the general point about PLA. It does not say that PLA entering the human body causes no rejection-related inflammatory reaction in surrounding tissue; that absolute assurance is unsupported. (LLM, conf=0.87)
- Not checked yetcites [77] Tan D.S. Diversity-oriented synthesis: Exploring the intersections between chemistry and biology Nat. Chem. Biol. 2005 1 74 84 10.1038/nchembio0705-74 16408003 source
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
None of the sources cited for this claim have been checked yet.
In the paper
“When using a polylactic acid–polyethylene glycol copolymer, the embedding rate reached 90%.”
§ Synthesis and Biological Application of Polylactic Acid > 3. Application > 3.1. Tissue Engineering
What the sources say
- Not checked yetcites [87] Waring M.J. Arrowsmith J. Leach A.R. Leeson P.D. Mandrell S. Owen R.M. Pairaudeau G. Pennie W.D. Pickett S.D. Wang J. An analysis of the attrition of drug candidates from four major pharmaceutical companies Nat. Rev. Drug Discov. 2015 14 475 486 10.1038/nrd4609 26091267 source
- Not checked yetcites [88] Langer R. Vacanti J.P. Tissue engineering Science 1993 260 920 926 10.1126/science.8493529 8493529 source
- Could not verifycites [89] Zhang Y. Sophocleous A.M. Schwendeman S.P. Inhibition of Peptide Acylation in PLGA Microspheres with Water-soluble Divalent Cationic Salts Pharm. Res. 2009 26 1986 1994 10.1007/s11095-009-9914-2 19533307 PMC4260456 sourceExperimental — accuracy not yet measured
The Introduction mentions PLA–PEG formulations only in a discussion of peptide acylation, not a 90% embedding rate. The Materials and Methods section on drug loading and encapsulation efficiency describes measurements of octreotide, not hemoglobin. Searches for hemoglobin and 90% found no passage supporting the claimed result. (LLM, conf=0.76)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Some plasticizers, such as low-molecular-weight citric acid, succinic acid, tartaric acid, and oxalate, are blended with PLA to change its mechanical and thermodynamic properties.”
§ Synthesis and Biological Application of Polylactic Acid > 2. PLA Synthesis and Properties > 2.4. Improvement of PLA Properties
What the sources say
- Not checked yetcites [66] Paul M.A. Alexandre M. Degee P. Henrist C. Rulmont A. Dubois P. New nanocomposite materials based on plasticized poly (l-lactide) and organo-modified montmorillonites: Thermal and morphological study Polymer 2003 44 443 450 10.1016/S0032-3861(02)00778-4 source
- Partly supportedcites [67] Paul M.A. Delcourt C. Alexandre M. Degee P. Monteverde F. Rulmont A. Dubois P. (Plasticized) polylactide/(organo-)clay nanocomposites by in situ intercalative polymerization Macromol. Chem. Phys. 2005 206 484 498 10.1002/macp.200400324 sourceExperimental — accuracy not yet measured
Our copy of Paul et al. (2005) does support the general idea that blending a plasticizer into PLA alters its properties: the 'In situ Polymerization in Presence of PEG' and 'Masterbatch Process' sections state that PLA's brittleness means it 'needs to be plasticized in order to fulfill mechanical requirements', and that 20 wt.-% PEG 1000 lowers the PLA matrix T_g to 26 °C (from 61 °C for nonplasticized chains, 'Clay' section) while raising melting enthalpy to 42.9 J/g; the PEG triblock section reports T_g falling to 41 °C and 12 °C at 8.5 and 16.2 wt.-% PEG. However, none of the specific plasticizers the claim names — citric acid, succinic acid, tartaric acid, oxalate — appear anywhere in our copy (searched: citric, succinic, tartaric, oxalate, low-molecular-weight plasticizer); the only plasticizers treated are PEG 1000 and residual L,L-lactide monomer ('lactide is known to be a good plasticizer for P(L,L-LA)'). Mechanical properties are also invoked only as motivation, not measured. The enumerated acid plasticizers are therefore not supported by this source. (LLM, conf=0.68)
- Not checked yetcites [68] Pluta M. Paul M.A. Alexandre M. Dubois P. Plasticized polylactide/clay nanocomposites. I. The role of filler content and its surface organo-modification on the physico-chemical properties J. Polym. Sci. Part B-Polym. Phys. 2006 44 299 311 10.1002/polb.20694 source
- Not checked yetcites [69] Tanoue S. Hasook A. Iemoto Y. Unryu T. Preparation of poly (lactic acid)/poly(ethylene glycol)/organoclay nanocomposites by melt compounding Polym. Compos. 2006 27 256 263 10.1002/pc.20174 source
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
31 more claims
Create a free account to see all 78 claims and to verify the 116 references still open.
- It may state two separate claims as one. 25
- Probably not a substantial claim. 22
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“On the other hand, in medicine, PLA can be applied in the areas of bioresorbent implants, surgical sutures, clamps, clips, surgical masks, or dressings [14,87,88,89,90,91].”
From Green Copolymers Based on Poly(Lactic Acid)—Short Review (2021) · cites this paper as [90]
Experimental — accuracy not yet measuredThe cited source says what the claim attributes to it.
In the citing paper
“This drug delivery system avoids inconsistent local concentration on account of drug release. Thus, the therapeutic effect is enhanced [90].”
From Green Copolymers Based on Poly(Lactic Acid)—Short Review (2021) · cites this paper as [90]
The cited source says what the claim attributes to it.
In the citing paper
“The microspheres obtained had a porous structure inside, which advanced drug release.”
From Green Copolymers Based on Poly(Lactic Acid)—Short Review (2021) · cites this paper as [90]
The cited source says what the claim attributes to it.
In the citing paper
“In vitro release was 49% in one month, making drug action time in the body longer.”
From Green Copolymers Based on Poly(Lactic Acid)—Short Review (2021) · cites this paper as [90]
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Synthesis and Biological Application of Polylactic Acid > 2. PLA Synthesis and Properties > 2.2. PLA Polymer
“Since LA is a chiral molecule with d-type and l-type isomers, three forms of polylactic acid are formed: poly-l-lactic acid (PLLA), poly-d-lactic acid (PDLA), and poly-d,l-lactic acid (PDLLA).”
§ Synthesis and Biological Application of Polylactic Acid > 2. PLA Synthesis and Properties > 2.2. PLA Polymer
“If l-lactic acid and d,l-lactic acid monomers are used to synthesize PLLA, the above problems are avoided [35,36].”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Synthesis and Biological Application of Polylactic Acid > Abstract
“Lactic acid, as a synthetic raw material of polylactic acid, can only be obtained by sugar fermentation.”
§ Synthesis and Biological Application of Polylactic Acid > 2. PLA Synthesis and Properties > 2.1. Lactic Acid
“Chemical synthesis methods have also been applied for the industrial production of lactic acid.”
Citations
Cites
Langer, R., & Vacanti, J. P. (1993) · Science · doi:10.1126/science.8493529 · Cited by 9,893
Stimuli-responsive nanocarriers for drug delivery
Mura, S., Nicolas, J., & Couvreur, P. (2013) · Nature Materials · doi:10.1038/nmat3776 · Cited by 6,289
A Multicenter, Randomized, Controlled Clinical Trial of Transfusion Requirements in Critical Care
Hébert, P. C., Wells, G., Blajchman, M. A., Marshall, J., Martin, C., Pagliarello, G., Tweeddale, M., Schweitzer, I., & Yetisir, E. (1999) · New England Journal of Medicine · doi:10.1056/nejm199902113400601 · Cited by 5,187
Plant Polyphenols as Dietary Antioxidants in Human Health and Disease
Pandey, K. B., & Rizvi, S. I. (2009) · Oxidative Medicine and Cellular Longevity · doi:10.4161/oxim.2.5.9498 · Cited by 3,942
Weiss, G., & Goodnough, L. T. (2005) · New England Journal of Medicine · doi:10.1056/nejmra041809 · Cited by 3,800
Long-Circulating and Target-Specific Nanoparticles: Theory to Practice
Moghimi, S. M., Hunter, A. C., & Murray, J. C. (2001) · Pharmacological Reviews · doi:10.1016/s0031-6997(24)01494-7 · Cited by 3,515
Denosumab for Prevention of Fractures in Postmenopausal Women with Osteoporosis
Cummings, S. R., Martin, J. S., McClung, M. R., Siris, E. S., Eastell, R., Reid, I. R., Delmas, P., Zoog, H. B., Austin, M., Wang, A., et al. (2009) · New England Journal of Medicine · doi:10.1056/nejmoa0809493 · Cited by 3,489
An Overview of Polylactides as Packaging Materials
Auras, R., Harte, B., & Selke, S. (2004) · Macromolecular Bioscience · doi:10.1002/mabi.200400043 · Cited by 3,454 · cited 2×
“Synthesis of polylactic acid (PLA) from L‐ and D‐lactic acids [28].”
BackgroundDietary polyphenols and the prevention of diseases
Scalbert, A., Manach, C., Morand, C., Rémésy, C., & Jiménez, L. (2005) · Critical Reviews in Food Science and Nutrition · doi:10.1080/1040869059096 · Cited by 2,999
Biodegradable Long-Circulating Polymeric Nanospheres
Gref, R., Minamitake, Y., Peracchia, M. T., Trubetskoy, V., Torchilin, V., & Langer, R. (1994) · Science · doi:10.1126/science.8128245 · Cited by 2,920
Research works printed but not linked: 1
- Bud R. A history of lactic-acid making–A chapter in the history of biotechnology-benninga,h Ann. Sci. 1993 50 597
Cited by
Items 101–200 of 492
Synthetic biodegradable polyesters for implantable controlled-release devices
Pothupitiya, J. U., Zheng, C., & Saltzman, W. M. (2022) · Expert Opinion on Drug Delivery · doi:10.1080/17425247.2022.2131768 · Cited by 29
“This has been shown to influence mechanical and thermal properties such as hardness, tensile strength, stiffness, melting points, and degradation rates of PLA [120].”
BackgroundLi, Y., Yuan, K., Deng, C., Tang, H., Wang, J., Dai, X., Zhang, B., Sun, Z., Ren, G., Zhang, H., et al. (2024) · Bioactive Materials · doi:10.1016/j.bioactmat.2024.08.031 · Cited by 38
“PLA is an important material for stents and coatings fabrication due to its biocompatibility, degradability, and mechanical strength [34].”
BackgroundSelf-citationRecent advances in selective laser–material interaction for biomedical device applications
Um, S., Hwang, S., Grigoropoulos, C. P., Jeon, H., & Ko, S. H. (2022) · Applied Physics Reviews · doi:10.1063/5.0101634 · Cited by 28
Insight into Nano-Fillers and Their Reinforcement onto Polylactic Acid
Chakraborty, A., Ghalsasi, P., & Radha, P. (2023) · Journal of Inorganic and Organometallic Polymers and Materials · doi:10.1007/s10904-023-02605-z · Cited by 25
“This adds another layer, indicating that PLA needs to be researched further to figure out the solution to overcome its disadvantages [27].”
BackgroundWang, B., Ye, X., Chen, G. L., Zhang, Y., Zeng, Z., Liu, C., Tan, Z., & Jie, X. (2024) · Frontiers in Bioengineering and Biotechnology · doi:10.3389/fbioe.2024.1273541 · Cited by 38
“Brie fl y, the experimental operation steps refer to our previous research (Li et al., 2020).”
BackgroundMethodInfluentialDukle, A., & Sankar, M. R. (2024) · Materials Today Communications · doi:10.1016/j.mtcomm.2024.109776 · Cited by 32
Huo, T., Zhou, L., Bian, X., & Wen, Y. (2025) · Advanced Composites and Hybrid Materials · doi:10.1007/s42114-025-01336-8 · Cited by 31
Combination of polylactide with cellulose for biomedical applications: a recent overview
Kopańska, A., Brzeziński, M., & Draczyński, Z. (2023) · Cellulose · doi:10.1007/s10570-023-05624-8 · Cited by 24
“Research on the use of polylactide in medicine, including regenerative medicine, has been conducted with high intensity for several decades (Li et al. 2020).”
Rodríguez-Reyna, S. L., Díaz-Aguilera, J. H., Acevedo-Parra, H. R., García, C. J., Gutiérrez, E. J., & Tapia, F. (2023) · Journal of the mechanical behavior of biomedical materials/Journal of mechanical behavior of biomedical materials · doi:10.1016/j.jmbbm.2023.106257 · Cited by 23
Akhila, B., Abhijith, V., Sreedharan, M., Ravindran, L., Sathian, A., Thomas, S., & Sreekala, M. S. (2025) · ACS Biomaterials Science & Engineering · doi:10.1021/acsbiomaterials.5c00194 · Cited by 30
Chen, K., Liao, C., Li, P., Li, X., Li, X., & Zuo, Y. (2022) · Journal of Polymers and the Environment · doi:10.1007/s10924-021-02359-0 · Cited by 24
“These characteristics render PLA an environmentally benign material for use in packaging [2–4] and biological medicine applications [5, 6].”
BackgroundSelf-citationWai, T. M., Rawi, N. F. M., Khalil, H. P. S. A., Mariatti, M., Rashedi, A., & Kassim, M. H. M. (2022) · Polymer Composites · doi:10.1002/pc.26681 · Cited by 25
Ishaque, N., Naseer, N., Abbas, M. A., Javed, F. T., Mushtaq, S., Ahmad, N. M., Khan, M. F. A., Ahmed, N., & Elaïssari, A. (2022) · Polymers · doi:10.3390/polym14173547 · Cited by 23
“Due to the chiral nature of lactic acid, several distinct forms of polylactide exist: poly-L-lactide (PLLA) is the product resulting from polymerization of L,L-lactide [25,26].”
BackgroundBilal, M., Niu, D., & Wang, Z. (2024) · Waste and Biomass Valorization · doi:10.1007/s12649-024-02705-y · Cited by 27
Sinsup, P., Teeranachaideekul, V., Makarasen, A., Chuenchom, L., Prajongtat, P., Techasakul, S., Yingyuad, P., & Dechtrirat, D. (2021) · Membranes · doi:10.3390/membranes11090648 · Cited by 22
de la Rosa‐Ramírez, H., Dominici, F., Ferri, J. M., Luzi, F., Puglia, D., Torre, L., López, J., & Samper, M. D. (2023) · Journal of Polymers and the Environment · doi:10.1007/s10924-023-02949-0 · Cited by 24
Glycerol-derived organic carbonates: environmentally friendly plasticizers for PLA
Seo, H. J., Seo, Y. H., Park, S. U., Lee, H. J., Lee, M. R., Park, J. H., Cho, W. Y., Lee, P. C., & Lee, B. Y. (2024) · RSC Advances · doi:10.1039/d3ra08922c · Cited by 24
“67 Importantly, both of these values are not signi cantly lower than the T g of high molecular weight PLA, which stands at 60 °C.”
BackgroundBühlmann, C. H., Mickan, B. S., Tait, S., & Bahri, P. A. (2021) · Chemical Engineering Journal · doi:10.1016/j.cej.2021.133243 · Cited by 27
Hybrid PLA-based biocomposites produced by DLP 3D printer with alumina and silica nanoparticles
Maleki, H., Asadi, P., Moghanian, A., Safaee, S., Najjar, I. M. R., & Fathy, A. (2024) · Materials Today Communications · doi:10.1016/j.mtcomm.2024.111469 · Cited by 25
Malik, M., Ali, Z., Khan, S., Zeb, A., Din, F. U., Alamri, A. H., & Lahiq, A. A. (2023) · Journal of Drug Delivery Science and Technology · doi:10.1016/j.jddst.2023.105238 · Cited by 22
Solution Blow Spinning: An Emerging Nanomaterials‐Based Wound‐Care Technology
Sk, M. S., Mwangomo, R., Daniel, L., & Gilmore, J. (2025) · Journal of Biomedical Materials Research Part B Applied Biomaterials · doi:10.1002/jbm.b.35513 · Cited by 21
Wang, Y., Su, X., Liu, Y., Hu, L., Lin, K., Xu, C., Sun, Z., Sun, C., Guo, H., & Shen, S. (2025) · Acta Pharmaceutica Sinica B · doi:10.1016/j.apsb.2025.05.040 · Cited by 25
“While some drug-loaded composites, such as polylactic acid and polyvinyl alcohol composites have been approved for drug delivery systems and biodegradable implants 43-46 , polyurethane can also be used for cardiovascular and soft tissue repair 47 .”
Wang, Y., Wu, H., Fan, S., Wu, J., & Yang, S. (2022) · Computer Methods in Biomechanics & Biomedical Engineering · doi:10.1080/10255842.2022.2045485 · Cited by 20
“Until now, PLA has been proved as the most widely used polymeric material for BRS because of its biocompatibility and biodegradability (Grabow et al. 2005; Li et al. 2020).”
Advancing strategies towards the development of tissue engineering scaffolds: a review
Pattanayak, I., Alex, Y., & Mohanty, S. (2023) · Journal of Materials Science · doi:10.1007/s10853-023-08798-5 · Cited by 19
“PLA material is completely degradable, which overcomes the white-pollution problem produced by petroleum-based products and has become a significant priority in science and technology’s long-term growth [24].”
BackgroundYang, X., Wang, X., Tang, L., Sun, Z., Gao, X. H., Zhao, Y., Hou, S., Shi, J., & Lv, Q. (2024) · Materials Today Bio · doi:10.1016/j.mtbio.2024.101431 · Cited by 22
“However, it ’ s hydrophobic nature has historically limited its research in the field of hemostatic materials [11].”
Bioactive Coatings Loaded with Osteogenic Protein for Metallic Implants
Gherasim, O., Grumezescu, A. M., Grumezescu, V., Andronescu, E., Neguț, I., Bîrcă, A. C., Gălățeanu, B., & Hudiță, A. (2021) · Polymers · doi:10.3390/polym13244303 · Cited by 22
Make it or break it: A review on PHA synthase and depolymerase proteins
Vilchis, I. V., & Karunakaran, E. (2024) · Journal of Polymers and the Environment · doi:10.1007/s10924-024-03474-4 · Cited by 26
Fabrication of Polymer/Graphene Biocomposites for Tissue Engineering
Meneses, J., van de Kemp, T., Costa‐Almeida, R., Pereira, R. F., Magalhães, F. D., Castilho, M. D., & Pinto, A. M. (2022) · Polymers · doi:10.3390/polym14051038 · Cited by 19
van Kampen, E. E. M., Ayyoubi, S., Willemsteijn, L., van Bommel, K. J. C., & Ruijgrok, E. J. (2022) · Pharmaceutics · doi:10.3390/pharmaceutics15010028 · Cited by 19
“Polylactic acid 50–80 (Tg) [37] • Biodegradable, thermoplastic polymer [38] • Not included in the STEP database [13] • GRAS • FDA-approved for oral use (Lactic acid) [14] • Only printed with relatively high temperatures so far (e.”
BackgroundYu, P., Lin, Y., & Chen, W. (2024) · Polymer Journal · doi:10.1038/s41428-024-00980-z · Cited by 20
“The advantages of PEG include biodegradability, low cost and polydispersity, chemical stability, good solvent solubility, and selective chemical reactivity, which inhibits side reactions [37].”
Wang, Z.-B., Wang, M., Ding, Z., Zhang, X.-S., & Wang, B. (2024) · Polymer science & technology. · doi:10.1021/polymscitech.4c00020 · Cited by 20
Wen, Y., Xu, M., Hu, Y., Bao, J., Yang, Q., Xiong, C., & Shi, Z. (2025) · Chemical Engineering Journal · doi:10.1016/j.cej.2025.161795 · Cited by 18
Alloplastic and Implant Materials for Bone Grafting: a Literature Review
Фаритович, М. У., Владимирович, Л. С., Borzunov, D. Y., Фанилевич, Г. И., Beylerli, O., & Yang, G. (2021) · Creative Surgery and Oncology · doi:10.24060/2076-3093-2021-11-4-343-353 · Cited by 18
Structure and Properties of PLA Composite Enhanced with Biomass Fillers from Herbaceous Plants
Na, H., Huang, J., Xu, H., Liu, F., Xie, L., Zhu, B., Wang, J., & Zhu, J. (2022) · JOURNAL OF RENEWABLE MATERIALS · doi:10.32604/jrm.2023.024181 · Cited by 21
Zhang, Q., Zhai, W., Cui, L., Liu, Y., Xie, W., Yu, Q., & Luo, H. (2023) · Polymer Bulletin · doi:10.1007/s00289-023-04691-y · Cited by 18
“…polymers (such as starch) could alleviate the above disadvantages and combine its advantages, while reducing the material cost and improving the degradation performance of composite materials, so as to partially replace 1 3 Polymer Bulletin (2023) 80:13319–13341 petroleum-based plastics [18].”
BackgroundImproved mechanical performance of biodegradable polyester based on 1,3-butanediol
Yu, J., Zhao, X., Liu, Y., Deng, M., Zhang, B., Pan, H., Zhang, H., Liu, B., Men, Y., Sun, Z., et al. (2023) · Polymer Degradation and Stability · doi:10.1016/j.polymdegradstab.2023.110425 · Cited by 18
Lednev, I. R., Salomatina, E. V., Ilyina, S., Zaitsev, S. D., Kovylin, R. S., & Смирнова, Л. А. (2021) · Materials · doi:10.3390/ma14174900 · Cited by 18
“Thus, the problem of the synthesis of polylactide with a high molecular weight, a low polydispersity index, and a high yield of the target product remains urgent [25].”
BackgroundChen, K.-J., Hung, F., Wang, Y.-T., & Yen, C.-W. (2021) · Journal of the mechanical behavior of biomedical materials/Journal of mechanical behavior of biomedical materials · doi:10.1016/j.jmbbm.2021.104949 · Cited by 17
PLA 3D Printing as a Straightforward and Versatile Fabrication Method for PDMS Molds
van der Borg, G., Warner, H. M., Ioannidis, M., van den Bogaart, G., & Roos, W. H. (2023) · Polymers · doi:10.3390/polym15061498 · Cited by 19
“It is used in the context of tissue engineering [18], medical implant applications [19], and drug delivery approaches [20].”
BackgroundEffects of polylactic acid coating on properties of porous Zn scaffolds as degradable materials
Yuan, P., Zhang, M., Wang, X., Qi, Y., Wang, T., Zhao, L., & Cui, C. (2023) · Materials Characterization · doi:10.1016/j.matchar.2023.112852 · Cited by 19
Prontera, C. T., Villani, F., Palamà, I. E., Maglione, M. G., Manini, P., Maiorano, V., & Tammaro, L. (2022) · Polymers for Advanced Technologies · doi:10.1002/pat.5618 · Cited by 19
“Dual-purpose” strategy of achieving fire safety and UV-resistance of polylactic acid
Cui, X., Chen, J., Gu, W., Liu, J., Li, H., Gu, X., Sun, J. F., & Zhang, S. (2024) · Composites Part A Applied Science and Manufacturing · doi:10.1016/j.compositesa.2024.108485 · Cited by 16
Green Routes toward Cross-Linkable and Robust Elastomers Derived from Biobased Fumaric Acid
Ji, H., Yang, H., Wan, Y., Li, L., Wang, J., Zhang, X., Yu, J., Zhou, X., Wang, R., & Zhang, L. (2022) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.2c01007 · Cited by 17
Biopolymer-based carbon conductive inks for printed electronics: a comprehensive review
Naik, N. U., Sunil, D., Rao, A., & Nayak, R. (2025) · Polymer Bulletin · doi:10.1007/s00289-025-05947-5 · Cited by 15
“PLA is a biodegradable and environmentally friendly polymer, synthesized from lactic acid monomers derived from renewable resources [81].”
Alzahrani, A. S., Alamry, K. A., & Hussein, M. A. (2025) · RSC Advances · doi:10.1039/d5ra04504e · Cited by 22
“139 Recent research has also explored PLA bers incorporated with chitosan to create a dual-action material.”
Sustainable Green Methods for the Extraction of Biopolymers
Kumawat, T. K., Kumawat, V., Sharma, S., Sharma, V. L., Pandit, A., Kandwani, N., & Biyani, M. (2022) · Springer series on polymer and composite materials · doi:10.1007/978-3-030-98392-5_5 · Cited by 20
Yan, Y., Ji, Q., Fu, R., Liu, C., Yang, J. H., Yin, X., Li, Q., & Huang, R. (2023) · Bioengineering & Translational Medicine · doi:10.1002/btm2.10497 · Cited by 15
“However, this material is hydrophobic, which is unfavorable for cell adhesion and growth.(128) It has been considered a novel direction of tissue engineering to blend PLA with other biomate-”
BackgroundReview on Cell Structure Regulation and Performances Improvement of Porous Poly(Lactic Acid)
Hou, Y., Pan, Y., Zhou, Z., Liu, C., Shen, C., & Liu, X. (2023) · Macromolecular Rapid Communications · doi:10.1002/marc.202300065 · Cited by 15
Influence of Molecular Weight on the Enzymatic Degradation of PLA Isomer Blends by a Langmuir System
Im, D., Gavande, V. M., Lee, H., & Lee, W. (2023) · Materials · doi:10.3390/ma16145087 · Cited by 22
“Many researchers have reported that the initial degra ation of biopolyesters is regulated by the physical accessibility of the polymer structure to abiotic conflicts [2,9,11,14,21].”
BackgroundResearch progress of absorbable stents
Song, Y., Li, B., Chen, H., & Yu, Z. (2023) · International Journal of Medical Sciences · doi:10.7150/ijms.90012 · Cited by 17
“…become a popular material; several different forms of polylactide exist: polyl-lactide (PLLA) is the product of the polymerisation of L, L-lactide [32, 33], poly (L-lactide-co-D, L-lactide) (PLD LLA) is used as a PLDLLA/TCP scaffold for bone engineering [34]; poly (lactic acid-co-glycolic acid)…”
MethodSilk-based intelligent fibers and textiles: structures, properties, and applications
Yang, X.-C., Wang, X., Wang, C., Zheng, H., Yin, M., Chen, K., & Qiao, S. (2024) · Chemical Communications · doi:10.1039/d4cc02276a · Cited by 15
Thirugnanasamabandam, A., Prabhu, B., Mageswari, V., Murugan, V., Ramachandran, K., & Kadirgama, K. (2024) · International Journal of Lightweight Materials and Manufacture · doi:10.1016/j.ijlmm.2024.08.003 · Cited by 15
Biomaterial-based drug delivery strategies for oral mucosa
Liu, J., Sun, J., Hu, J., Xue, H., Lei, L., & Pan, X. (2025) · Colloids and Surfaces B Biointerfaces · doi:10.1016/j.colsurfb.2025.114604 · Cited by 19
Wang, Y., Wang, X., Xie, M., Zhou, Z., & Xu, H. (2022) · Polymer Composites · doi:10.1002/pc.26903 · Cited by 14
Dual-modified starch micelles as a promising nanocarrier for doxorubicin
Yun, L., Li, K., Liu, C., Deng, L., & Li, J. (2022) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2022.07.141 · Cited by 13
Lv, J., Wu, Y., Cao, Z., Liu, X., Sun, Y., Zhang, P., Zhang, X., Tang, K., Cheng, M., Yao, Q., et al. (2023) · Pharmaceutics · doi:10.3390/pharmaceutics15082145 · Cited by 15
Barchiki, F., Fracaro, L., Dominguez, A. C., Senegaglia, A. C., Vaz, I. M., Junior, P. C. S., de Moura, S. A. B., & Brofman, P. R. S. (2023) · Polymers · doi:10.3390/polym15244629 · Cited by 18
“These multiple FDA approvals validate the extensive adaptability of PLA in clinical settings [22,23].”
BackgroundProperties and Performance Relationship of Biopolymers in Textile Industry
Fazal‐ur‐Rehman, Zhara, H., Adeel, S., Özomay, Z., & Mia, R. (2024) · Springer eBooks · doi:10.1007/978-981-97-0684-6_4 · Cited by 19
Wu, Y., Lin, X., Chen, L., Gan, D., Li, R., Liu, Y., Song, L., Hao, X., Dong, T., Liu, L., et al. (2021) · Materials Today Communications · doi:10.1016/j.mtcomm.2021.103085 · Cited by 16
Ren, Z., Liu, L., Tang, T., Huang, K., & Huang, Z. (2024) · Food Bioscience · doi:10.1016/j.fbio.2024.105615 · Cited by 13
Biopolymers in Biotechnology and Tissue Engineering: A Comprehensive Review
Grabowski, M., Gmyrek, D., Żurawska, M., & Trusek-Hołownia, A. (2025) · Macromol—A Journal of Macromolecular Research · doi:10.3390/macromol5030034 · Cited by 17
Enzymatic Degradation of PLA: Preferential Degradation of the Amorphous Fraction
Shrestha, S., Snowdon, M. R., & Levin, D. B. (2025) · Polymers · doi:10.3390/polym17223042 · Cited by 21
“…∆ Hc) × 100/ ∆ H 0 m, where Xc is the degree of crystallinity, ∆ Hm is the enthalpy during melting, ∆ Hc is the exothermic peak enthalpy, and ∆ H 0 m is the enthalpy for the normalized enthalpy values (J/g) for 100% crystalline PLA polymer, which was reported to be 93.7 J/g in the literature [23].”
InfluentialLv, Z., Fu, K., & Zhang, Q. (2023) · Colloids and Surfaces B Biointerfaces · doi:10.1016/j.colsurfb.2023.113429 · Cited by 15
Roca, F. G., Martínez‐Ramos, C., Ivashchenko, S., García‐Bernabé, A., Compañ, V., & Pradas, M. M. (2023) · ACS Applied Polymer Materials · doi:10.1021/acsapm.3c00776 · Cited by 14
Ren, F., Li, X., Xian, J., Han, X., Cao, L., Pan, X., & Wu, J. (2022) · Journal of Polymer Science · doi:10.1002/pol.20220269 · Cited by 13
Self-citationAdzkia, Q. A. A., Noviyanti, A. R., Cahyana, Y., Torres‐Giner, S., & Rukayadi, Y. (2025) · Green Chemistry Letters and Reviews · doi:10.1080/17518253.2025.2535392 · Cited by 13
Agriculture waste to bioplastics: a perfect substitution of plastics
Rai, P. K., & Choure, K. (2023) · Elsevier eBooks · doi:10.1016/b978-0-323-89928-4.00011-0 · Cited by 23
Gebrehiwot, S. Z., Espinosa-Leal, L., Andersson, M., & Remes, H. (2023) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-023-08278-6 · Cited by 15
Yang, W., Wang, J., Jia, L., Li, J., & Liu, S. (2023) · Gels · doi:10.3390/gels9080647 · Cited by 12
“Polylactic acid (PLA) is a hydrophobic polymer that can be used in biomedicine because it is a lactic acid derivative made from renewable substances, so it has good biocompatibility and degradability [20,21].”
BackgroundPolylactide/poly(vinyl monomer) block copolymers for specific applications
Bednarek, M., & Grabowski, M. (2024) · Journal of macromolecular science. Part C, Reviews in macromolecular chemistry and physics/Journal of macromolecular science. Reviews in macromolecular chemistry and physics · doi:10.1080/15583724.2024.2310105 · Cited by 15
Ye, J., Yu, W., Ge, J., Qu, X., Mohideen, M. M., Wang, C., Hu, P., & Liu, Y. (2024) · Materials Today Communications · doi:10.1016/j.mtcomm.2024.108353 · Cited by 15
Economics and commercialization of bioplastics
Lepe, P. G. T., Heredia, K. V., Namur, E. C., Sandoval, G., & García-Enriquez, S. (2024) · Elsevier eBooks · doi:10.1016/b978-0-323-95199-9.00018-4 · Cited by 14
Chen, J., Liu, X., Hong, S., Mo, J., Peng, J., Su, T., Guo, Q., Lin, Y., Wang, L., & Ma, C. (2024) · Colloids and Surfaces A Physicochemical and Engineering Aspects · doi:10.1016/j.colsurfa.2024.133837 · Cited by 13
Main Chain Modified Polylactides. Methods of Synthesis and Applications
Biela, T., Kubisa, P., & Łapienis, G. (2024) · Journal of macromolecular science. Part C, Reviews in macromolecular chemistry and physics/Journal of macromolecular science. Reviews in macromolecular chemistry and physics · doi:10.1080/15583724.2024.2333742 · Cited by 12
Liu, C., Yuan, W., Ma, W., Yang, M., Yang, M., Cui, L., & Guan, C. (2024) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2024.135226 · Cited by 13
Advancements in Drug Delivery Systems for the Treatment of Sarcopenia: An Updated Overview
Najm, A., Moldoveanu, E.-T., Niculescu, A.-G., Grumezescu, A. M., Beuran, M., & Gașpar, B. S. (2024) · International Journal of Molecular Sciences · doi:10.3390/ijms251910766 · Cited by 13
“In this way, researchers need to optimize drug delivery mechanisms using hydrogels so that the therapeutic effects are superior and to overcome the challenges mentioned above.”
BackgroundBuyuksoy-Fekraoui, K., Lacoste, C., Pucci, M. F., Lopez‐Cuesta, J., & Perrin, D. (2022) · Materials · doi:10.3390/ma15093398 · Cited by 15
“The synthesis of PLA is carried out either by polymerization of lactic acid or lactide [1].”
MethodBiomimetic materials: a promising strategy for periodontal tissue engineering and regeneration
Zhang, Q., Gou, C., & Zhang, Z. (2025) · Frontiers in Bioengineering and Biotechnology · doi:10.3389/fbioe.2025.1639170 · Cited by 16
“Their large pores and directional structure promoted cell migration and attachment, thereby enhancing bone tissue regeneration via the BMP-2/Smad/ runt-related transcription factor 2 pathway (Merkel et al., 2023; Zhao et al., 2020).”
Preparation and Properties of Graft-Modified Bagasse Cellulose/Polylactic Acid Composites
Wang, Y., Xu, H., Huang, L., Han, X.-X., Wei, Z., Mo, Q. F., Wang, X., & Li, Y. (2023) · Journal of Natural Fibers · doi:10.1080/15440478.2022.2164822 · Cited by 11
“Based on the underlying principle, PLA synthesis methods can be divided into two categories: direct polymerization (Rahmayetty, Prasetya, and Gozan 2017;Yoo, Kim, and Lee 2006) and ring-opening polymerization (Li et al. 2020;Zhang and Zhang 2010).”
MethodSelf-citationPaul, A., Sreedevi, K., Sharma, S. S., & Anjana, V. N. (2023) · Springer eBooks · doi:10.1007/978-981-19-0710-4_44 · Cited by 12
Nanoengineered Endocytic Biomaterials for Stem Cell Therapy
Wang, Y., Sun, C., Liu, Z., Zhang, S., Gao, K., Yi, F., Zhou, W., & Liu, H. (2024) · Advanced Functional Materials · doi:10.1002/adfm.202410714 · Cited by 12
He, X., Good, A., Kalou, W., Ahmad, W., Dutta, S., Chen, S., Lin, C. N., Krishnan, K. C., Fan, Y., Huang, W. C., et al. (2024) · Cells · doi:10.3390/cells13242098 · Cited by 15
The Influence of In Vitro Degradation on the Properties of Polylactic Acid Electrospun Fiber Mats
Abdullah, K. K., & Molnár, K. (2024) · Fibers · doi:10.3390/fib13010001 · Cited by 11
“Among synthetic polymers, PLA is an eco-friendly option, widely favored by researchers, and commonly used in various applications [21–23].”
Sun, P., Liu, K., Dong, C., Li, Y., Zhu, H., Fang, M., Fu, D., & Liu, X. (2025) · Frontiers of Chemical Science and Engineering · doi:10.1007/s11705-025-2523-8 · Cited by 16
Self-citationMacías‐Naranjo, M., Sánchez‐Domínguez, M., Rodriguez, C. A., García‐López, E., & Vázquez, E. (2025) · Journal of Applied Polymer Science · doi:10.1002/app.57064 · Cited by 11
Gunasekaran, A., Chen, H., Ponnusamy, V. K., Sorrentino, A., & Anandan, S. (2021) · Journal of Polymer Research · doi:10.1007/s10965-021-02615-w · Cited by 11
Liu, F., Li, B., Sun, D., Li, F., & Pei, X. (2022) · Korean Journal of Chemical Engineering · doi:10.1007/s11814-021-0992-0 · Cited by 11
Anti-Tumor and Anti-Metastasis Effects of Berbamine-Loaded Lipid Nanoparticles on Pancreatic Cancer
Tang, Z., Yi-Chun, N., Xu, Z., Shi, Y., Liu, Y., Fu, W., Zheng, M., He, H., & Wu, T. (2022) · Anti-Cancer Agents in Medicinal Chemistry · doi:10.2174/1871520622666220501161636 · Cited by 11
Biopolymers: Global Carbon Footprint and Climate Change
Stoica, D., Alexe, P., Ivan, A. S., Moraru, D. I., Ungureanu, C. V., Stanciu, S., & Stoica, M. (2022) · Springer series on polymer and composite materials · doi:10.1007/978-3-030-98392-5_3 · Cited by 14
Zhao, K., Hu, Z., Zhou, M., Chen, Y., Zhou, F., Ding, Z., & Zhu, B. (2023) · Journal of Biomaterials Applications · doi:10.1177/08853282231197901 · Cited by 11
Surface Topography of PLA Implants Defines the Outcome of Foreign Body Reaction: An In Vivo Study
Иванова, Е., Fayzullin, A. L., Минаев, Н. В., Dolganova, I. N., Serejnikova, N. B., Gafarova, E. R., Tokarev, M., Minaeva, E., Aleksandrova, P. V., Reshetov, I. V., et al. (2023) · Polymers · doi:10.3390/polym15204119 · Cited by 14
Poly-L-lactic acid in aesthetic medicine
Murakov, S. V., Razumovskaya, E. A., Zakharov, D. Y., Timofeev, A. V., & Nikitina, E. A. (2023) · Plastic Surgery and Aesthetic Medicine · doi:10.17116/plast.hirurgia2023041101 · Cited by 12
Liu, Q., Fu, Y., Wu, B., Tang, J., Wang, Y., Wu, Y., Zhang, M., Shen, S., Shen, Y., Gao, C., et al. (2022) · Biomaterials · doi:10.1016/j.biomaterials.2022.121665 · Cited by 11
Zuluaga‐Parra, J. D., Ramos-deValle, L. F., Sánchez‐Valdés, S., Torres‐Lubián, J. R., Pérez-Mora, R., Ramírez‐Vargas, E., Martínez‐Colunga, J. G., da Silva, L. A., Vázquez‐Rodríguez, S., Lozano, T., et al. (2022) · Iranian Polymer Journal · doi:10.1007/s13726-022-01120-1 · Cited by 12
“Generally, it is obtained from ring-opening polymerization of the monomer (lactide), which is a cyclic dimer produced from the depolymerization of lactic acid [4].”
BackgroundKalathil, N. C., Shah, M. R., Lailakumari, V. C., Prabhakaran, P., Kumarapilla, H., & Kumar, G. S. V. (2024) · ACS Applied Bio Materials · doi:10.1021/acsabm.4c00669 · Cited by 10
Ahmed, A. S., Saleh, T. A.-K., Mohammad, H. J., Hasan, A. A., Mahdi, S. A., Alhuwaymil, Z., Alshareef, S. A., Mahmood, A. T., & Al-Mashhadani, M. H. (2024) · Radiation Physics and Chemistry · doi:10.1016/j.radphyschem.2024.112494 · Cited by 10
Advances in biomaterials-based tissue engineering for regeneration of female reproductive tissues
Kim, Y. H., Kim, H., & Hong, I. (2025) · Biofabrication · doi:10.1088/1758-5090/adae38 · Cited by 14
“Consequently, lactic acid plays a pivotal role in the body, acting as a core component in various metabolic processes and being produced by animals, microorganisms, and plants [59].”
Wendou, D., Li, J., Jia, T., Zhengxiang, W., & Fan, S. (2025) · Journal of Coatings Technology and Research · doi:10.1007/s11998-024-01072-6 · Cited by 10
“162,163 Following the printing process with conventional water-based inks, the ester bonds of PLA may be hydrolyzed and broken under alkaline conditions, hydrophilic humidity, and heat.”
Mendoza-Duarte, M. E., Roacho-Pérez, J. A., Quiroz-Reyes, A. G., Garza-Treviño, E. N., Sanchez-Dominguez, C. N., García‐Casillas, P. E., & Vega‐Ríos, A. (2023) · Journal of Polymers and the Environment · doi:10.1007/s10924-023-03019-1 · Cited by 11
“Nevertheless, PLA exhibits fragile behavior and low elongation [26–28].”
Synthesis of Poly-Lactic Acid by Ring Open Polymerization from Beer Spent Grain for Drug Delivery
Vakati, S. R., Vanderlaan, G., Gacura, M. D., Ji, X., Chen, L., & Piovesan, D. (2024) · Polymers · doi:10.3390/polym16040483 · Cited by 9
“PLA polymers are an ideal option for transient biomedical applications since the ester bonds in the polymer backbone are amenable to hydrolysis without the need for additional procedures or enzymes and because the breakdown products are non-toxic and minimize the host immune response [15].”
Background
Metadata
- Authors
- Li, G., Zhao, M., Xu, F., Yang, B., Li, X., Meng, X., Teng, L., Sun, F., & Li, Y.
- Affiliations
- Jilin University (CN)
- Corresponding author
- Sun, Fengying
- Li, Youxin
- ORCID
- Venue
- Molecules
- Publisher
- MDPI AG
- Published
- 2020-10-29
- Volume
- 25
- Issue
- 21
- Pages
- 5023
- ISSN
- 1420-3049 (ISSN-L)
- PMC
- PMC7662581
- OpenAlex
- W3096086014
- Cited by
- 492
- References
- 140
- Citations by year
- 2026: 55 · 2025: 115 · 2024: 112 · 2023: 105 · 2022: 71 · 2021: 34
- FWCI
- 3.52
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Molecules (publishedVersion, cc-by)
- PubMed Central (publishedVersion, cc-by)
- PubMed (publishedVersion)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Funders
- People's Government of Jilin Province (20180101269JC)
- Topics
- Physical Sciences › Materials Science › Biomaterials › biodegradable polymer synthesis and properties
- Physical Sciences › Engineering › Biomedical Engineering › Bone Tissue Engineering Materials
- Health Sciences › Medicine › Surgery › Surgical Sutures and Adhesives
- Keywords
- polylactic acid, lactic acid, biodegradable polymers, biocompatibility, polymer synthesis, polymer modification, drug delivery, implants, tissue engineering, biodegradation, sugar fermentation
- MeSH terms
- Biocompatible Materials, Humans, Polyesters, Drug Delivery Systems, Prostheses and Implants, Tissue Engineering
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-01, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-01 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol and qwen3.8-omni-flash).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.