The DOI matches its Crossref record; 52 of the 52 references it cites were found in a registry or an index.
Extrusion Bioprinting of Shear‐Thinning Gelatin Methacryloyl Bioinks
Open accessAbstract
Bioprinting is an emerging technique for the fabrication of 3D cell‐laden constructs. However, the progress for generating a 3D complex physiological microenvironment has been hampered by a lack of advanced cell‐responsive bioinks that enable bioprinting with high structural fidelity, particularly in the case of extrusion‐based bioprinting. Herein, this paper reports a novel strategy to directly bioprint cell‐laden gelatin methacryloyl (GelMA) constructs using bioinks of GelMA physical gels (GPGs) achieved through a simple cooling process. Attributed to their shear‐thinning and self‐healing properties, the GPG bioinks can retain the shape and form integral structures after deposition, allowing for subsequent UV crosslinking for permanent stabilization. This paper shows the structural fidelity by bioprinting various 3D structures that are typically challenging to fabricate using conventional bioinks under extrusion modes. Moreover, the use of the GPG bioinks enables direct bioprinting of highly porous and soft constructs at relatively low concentrations (down to 3%) of GelMA. It is also demonstrated that the bioprinted constructs not only permit cell survival but also enhance cell proliferation as well as spreading at lower concentrations of the GPG bioinks. It is believed that such a strategy of bioprinting will provide many opportunities in convenient fabrication of 3D cell‐laden constructs for applications in tissue engineering, regenerative medicine, and pharmaceutical screening.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Matrix elasticity directs stem cell lineage specification
Engler, A. J., Sen, S., Sweeney, H. L., & Discher, D. E. (2006) · Cell · doi:10.1016/j.cell.2006.06.044 · Cited by 13,915
A review on polymer nanofibers by electrospinning and their applications in nanocomposites
Huang, Z.-M., Zhang, Y.-Z., Kotaki, M., & Ramakrishna, S. (2003) · Composites Science and Technology · doi:10.1016/s0266-3538(03)00178-7 · Cited by 7,556
Self-citation3D bioprinting of tissues and organs
Murphy, S. V., & Atala, A. (2014) · Nature Biotechnology · doi:10.1038/nbt.2958 · Cited by 7,034
Tissue Cells Feel and Respond to the Stiffness of Their Substrate
Discher, D. E., Janmey, P., & Wang, Y.-L. (2005) · Science · doi:10.1126/science.1116995 · Cited by 6,382
Electrospinning of Nanofibers: Reinventing the Wheel?
Li, D., & Xia, Y. (2004) · Advanced Materials · doi:10.1002/adma.200400719 · Cited by 5,521
Synthesis, properties, and biomedical applications of gelatin methacryloyl (GelMA) hydrogels
Yue, K., Trujillo-de Santiago, G., Alvarez, M. M., Tamayol, A., Annabi, N., & Khademhosseini, A. (2015) · Biomaterials · doi:10.1016/j.biomaterials.2015.08.045 · Cited by 3,146
Self-citationA 3D bioprinting system to produce human-scale tissue constructs with structural integrity
Kang, H.-W., Lee, S. J., Ko, I. K., Kengla, C., Yoo, J. J., & Atala, A. (2016) · Nature Biotechnology · doi:10.1038/nbt.3413 · Cited by 2,622
Cell-laden microengineered gelatin methacrylate hydrogels
Nichol, J. W., Koshy, S. T., Bae, H., Hwang, C. M., Yamanlar, S., & Khademhosseini, A. (2010) · Biomaterials · doi:10.1016/j.biomaterials.2010.03.064 · Cited by 2,377
Self-citationContinuous liquid interface production of 3D objects
Tumbleston, J. R., Shirvanyants, D., Ermoshkin, N., Janusziewicz, R., Johnson, A. R., Kelly, D., Chen, K., Pinschmidt, R., Rolland, J. P., Ermoshkin, A., et al. (2015) · Science · doi:10.1126/science.aaa2397 · Cited by 2,278
3D bioprinting of vascularized, heterogeneous cell-laden tissue constructs
Kolesky, D. B., Truby, R. L., Gladman, A. S., Busbee, T. A., Homan, K. A., & Lewis, J. A. (2014) · Advanced Materials · doi:10.1002/adma.201305506 · Cited by 2,102
Cited by
Hydrogel Bioink Reinforcement for Additive Manufacturing: A Focused Review of Emerging Strategies
Chimene, D., Kaunas, R., & Gaharwar, A. K. (2020) · Advanced Materials · doi:10.1002/adma.201902026 · Cited by 600
Yin, J., Yan, M., Wang, Y., Fu, J., & Suo, H. (2018) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.7b16059 · Cited by 598
Bioinks and bioprinting technologies to make heterogeneous and biomimetic tissue constructs
Ashammakhi, N., Ahadian, S., Xu, C., Montazerian, H., Ko, H., Nasiri, R., Barros, N., & Khademhosseini, A. (2019) · Materials Today Bio · doi:10.1016/j.mtbio.2019.100008 · Cited by 549
Self-citationUnagolla, J. M., & Jayasuriya, A. C. (2020) · Applied Materials Today · doi:10.1016/j.apmt.2019.100479 · Cited by 544
Recent Advances in Extrusion‐Based 3D Printing for Biomedical Applications
Placone, J. K., & Engler, A. J. (2018) · Advanced Healthcare Materials · doi:10.1002/adhm.201701161 · Cited by 486
3D Bioprinting: from Benches to Translational Applications
Heinrich, M. A., Liu, W., Jimenez, A., Yang, J., Akpek, A., Liu, X., Pi, Q., Mu, X., Hu, N., Schiffelers, R. M., et al. (2019) · Small · doi:10.1002/smll.201805510 · Cited by 437
Self-citationSpatiotemporal hydrogel biomaterials for regenerative medicine
Brown, T. E., & Anseth, K. S. (2017) · Chemical Society Reviews · doi:10.1039/c7cs00445a · Cited by 428
Fundamentals and Applications of Photo-Cross-Linking in Bioprinting
Lim, K. S., Galarraga, J. H., Cui, X., Lindberg, G. C. J., Burdick, J. A., & Woodfield, T. B. F. (2020) · Chemical Reviews · doi:10.1021/acs.chemrev.9b00812 · Cited by 416
Extrusion 3D Printing of Polymeric Materials with Advanced Properties
Jiang, Z., Diggle, B., Tan, M. L., Viktorova, J., Bennett, C. W., & Connal, L. A. (2020) · Advanced Science · doi:10.1002/advs.202001379 · Cited by 408
Ma, X., Liu, J., Zhu, W., Tang, M., Lawrence, N., Yu, C., Gou, M., & Chen, S. (2018) · Advanced Drug Delivery Reviews · doi:10.1016/j.addr.2018.06.011 · Cited by 401
Crosslinking Strategies for 3D Bioprinting of Polymeric Hydrogels
GhavamiNejad, A., Ashammakhi, N., Wu, X. Y., & Khademhosseini, A. (2020) · Small · doi:10.1002/smll.202002931 · Cited by 400
Self-citationZhang, Y. S., Haghiashtiani, G., Hübscher, T., Kelly, D. J., Lee, J. M., Lutolf, M., McAlpine, M. C., Yeong, W. Y., Zenobi-Wong, M., & Malda, J. (2021) · Nature Reviews Methods Primers · doi:10.1038/s43586-021-00073-8 · Cited by 391
Self-citationAdvances in Extrusion 3D Bioprinting: A Focus on Multicomponent Hydrogel‐Based Bioinks
Cui, X., Li, J., Hartanto, Y., Durham, M., Tang, J., Zhang, H., Hooper, G., Lim, K., & Woodfield, T. (2020) · Advanced Healthcare Materials · doi:10.1002/adhm.201901648 · Cited by 383
Aqueous Two‐Phase Emulsion Bioink‐Enabled 3D Bioprinting of Porous Hydrogels
Ying, G., Jiang, N., Maharjan, S., Yin, Y., Chai, R., Cao, X., Yang, J., Miri, A. K., Hassan, S., & Zhang, Y. S. (2018) · Advanced Materials · doi:10.1002/adma.201805460 · Cited by 377
Self-citationGao, F., Xu, Z., Liang, Q., Li, H., Peng, L., Wu, M., Zhao, X., Cui, X., Ruan, C., & Liu, W. (2019) · Advanced Science · doi:10.1002/advs.201900867 · Cited by 365
Self-citationDaly, A. C., Prendergast, M. E., Hughes, A. J., & Burdick, J. A. (2021) · Cell · doi:10.1016/j.cell.2020.12.002 · Cited by 332
Boularaoui, S., Al Hussein, G., Khan, K. A., Christoforou, N., & Stefanini, C. (2020) · Bioprinting · doi:10.1016/j.bprint.2020.e00093 · Cited by 320
An Overview on Materials and Techniques in 3D Bioprinting Toward Biomedical Application
Vanaei, S., Parizi, M. S., Vanaei, S., Salemizadehparizi, F., & Vanaei, H. R. (2021) · Engineered Regeneration · doi:10.1016/j.engreg.2020.12.001 · Cited by 308
Shi, L., Ding, P., Wang, Y., Zhang, Y., Ossipov, D., & Hilborn, J. (2019) · Macromolecular Rapid Communications · doi:10.1002/marc.201800837 · Cited by 303
Self-citationPrint Me An Organ! Why We Are Not There Yet
Ng, W. L., Chua, C. K., & Shen, Y.-F. (2019) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2019.101145 · Cited by 287
The rheology of direct and suspended extrusion bioprinting
Cooke, M. E., & Rosenzweig, D. H. (2021) · APL Bioengineering · doi:10.1063/5.0031475 · Cited by 284
Rapid printing of bio-inspired 3D tissue constructs for skin regeneration
Zhou, F., Hong, Y., Liang, R., Zhang, X., Liao, Y., Jiang, D., Zhang, J., Sheng, Z., Xie, C., Peng, Z., et al. (2020) · Biomaterials · doi:10.1016/j.biomaterials.2020.120287 · Cited by 282
Liu, W., Zhong, Z., Hu, N., Zhou, Y., Maggio, L., Miri, A. K., Fragasso, A., Jin, X., Khademhosseini, A., & Zhang, Y. S. (2018) · Biofabrication · doi:10.1088/1758-5090/aa9d44 · Cited by 280
Self-citationEmerging Technologies in Multi‐Material Bioprinting
Ravanbakhsh, H., Karamzadeh, V., Bao, G., Mongeau, L., Juncker, D., & Zhang, Y. S. (2021) · Advanced Materials · doi:10.1002/adma.202104730 · Cited by 266
Self-citationBioinks and bioprinting: A focused review
Mobaraki, M., Ghaffari, M., Yazdanpanah, A., Luo, Y., & Mills, D. K. (2020) · Bioprinting · doi:10.1016/j.bprint.2020.e00080 · Cited by 258
Polymeric Systems for Bioprinting
Bedell, M. L., Navara, A. M., Du, Y., Zhang, S., & Mikos, A. G. (2020) · Chemical Reviews · doi:10.1021/acs.chemrev.9b00834 · Cited by 258
Biomaterials-based 3D cell printing for next-generation therapeutics and diagnostics
Jang, J., Park, J. Y., Gao, G., & Cho, D.-W. (2018) · Biomaterials · doi:10.1016/j.biomaterials.2017.11.030 · Cited by 254
Bom, S., Ribeiro, R., Ribeiro, H. M., Santos, C., & Marto, J. (2022) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2022.121506 · Cited by 230
Portable hand-held bioprinters promote in situ tissue regeneration
Pazhouhnia, Z., Beheshtizadeh, N., Namini, M. S., & Lotfibakhshaiesh, N. (2022) · Bioengineering & Translational Medicine · doi:10.1002/btm2.10307 · Cited by 60
3D bioprinting lobule-like hepatorganoids with induced vascularization for orthotopic implantation
Yan, J., Ye, Z., Lu, Y., Yuan, Y., Wang, X., Yan, T., Yin, J., & Wang, Y. (2025) · Materials Today Bio · doi:10.1016/j.mtbio.2025.101515 · Cited by 15
Metadata
- Authors
- Liu, W., Heinrich, M. A., Zhou, Y., Akpek, A., Hu, N., Liu, X., Guan, X., Zhong, Z., Jin, X., Khademhosseini, A., & Zhang, Y. S.
- Venue
- Advanced Healthcare Materials
- Publisher
- Wiley
- Published
- 2017-05-02
- Volume
- 6
- Issue
- 12
- ISSN
- 2192-2640 (ISSN-L)
- 2192-2659
- OpenAlex
- W2610636146
- Cited by
- 503
- References
- 52
- FWCI
- 17.81
- Type
- journal article
- Language
- en
- Open access
- bronze
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.