The DOI matches its Crossref record; 95 of the 95 references it cites were found in a registry or an index; 10 of the 46 sources its claims cite were checked for support.
Synthesis of Pt Carbon Aerogel Electrocatalysts with Multiscale Porosity Derived from Cellulose and Chitosan Biopolymer Aerogels via Supercritical Deposition for Hydrogen Evolution Reaction
Open accessAbstract
The aim of this study is to investigate the activity and stability of carbon aerogel‐supported platinum electrocatalysts in the hydrogen evolution reaction, compared to current solutions based on carbon black. Self‐synthesized carbon aerogels (pyrolyzed cellulose, and chitosan‐based aerogels) with multiscale porosity and high overall specific surface area (up to ≈2500 m2 g−1), as well as Vulcan XC‐72R supports were loaded via supercritical deposition (SCD) with platinum nanoparticles (mean particle diameter ≈1.3–2.0 nm, 2.8–3.8 wt% Pt loading). Overpotentials ranged from 46.5 to 50.0 mV at 10 mA cm−2, whereas self‐synthesized electrocatalysts had similar overpotentials as compared to a commercial catalyst with ≈8–10 times higher Pt loading. In addition, Pt‐carbon aerogel electrocatalysts had higher stability and durability as compared to Pt‐Vulcan, most probably due to the high micro‐ to mesoporosity of carbon aerogels, which promotes nanoparticle stability. The current density at 40 mV for Pt‐Vulcan decreased by 80% after 20 h, whereas an insignificant drop was observed for Pt‐carbon aerogels. These results show that the applied combination of materials (biopolymer‐based carbon aerogels) and loading method (SCD) are a promising approach for synthesizing stable electrocatalysts with reduced platinum content for green hydrogen production.
Overview
CoChat Summary
TL;DR
This study synthesizes Pt electrocatalysts by supercritical deposition (SCD) of Pt nanoparticles onto carbon aerogels (CAs) derived from cellulose and chitosan biopolymer aerogels, and compares them to Pt on commercial Vulcan XC-72R carbon black for the hydrogen evolution reaction (HER). The CA-supported catalysts matched or exceeded a commercial 30 wt% Pt/C catalyst in activity at 8–10× lower Pt loading, and showed markedly better stability.
Key findings
- Pt loadings via SCD were 2.8–3.8 wt% with mean Pt nanoparticle diameters of ~1.3–2.0 nm; overpotentials at 10 mA cm⁻² were 46.6 mV (Pt-cellulose-CA), 49.5 mV (Pt-chitosan-CA), 48.9 mV (Pt-Vulcan), and 50 mV (Pt-C 30 wt%), with Tafel slopes ~30 mV dec⁻¹ for all.
- At 40 mV, mass activity was 12× greater for Pt-Vulcan and Pt-cellulose-CA and 16× higher for Pt-chitosan-CA than Pt-C 30 wt% (values: 1.8 ± 0.21, 2.3 ± 0.02, 1.6 ± 0.09 vs 0.14 ± 0.01 A mg⁻¹Pt); the authors attribute this to mass-transfer limitation rather than intrinsic activity.
- Stability: after 1000 cycles, potential shifts at 20 mA cm⁻² were 10.5 mV (Pt-cellulose-CA), 11.3 mV (Pt-chitosan-CA), and 34.07 mV (Pt-Vulcan). In 20 h chronoamperometry at 40 mV, Pt-Vulcan current density dropped 80%, while Pt-CA catalysts stayed largely constant.
- Textural data: cellulose-CA had the largest specific surface area (1440 m² g⁻¹ for pores <2 nm; 990 m² g⁻¹ for <1.5 nm), chitosan-CA 176 m² g⁻¹ (<2 nm) and 613 m² g⁻¹ (<1.5 nm), Vulcan 180 m² g⁻¹ (<2 nm); chitosan-CA contained 11 wt% nitrogen.
Methods
- Biopolymer aerogel beads were made by dripping/dissolution, solvent exchange to ethanol, supercritical drying, then carbonization at 800 °C under N₂; Pt was loaded by SCD using Pt(cod)me₂ in scCO₂ at 80 °C and 15.53 MPa for 24 h, followed by thermal conversion at 200 °C for 4 h under N₂.
- Supports and catalysts were characterized by N₂ and CO₂ physisorption, XRD, ICP-MS, XPS, Raman, SEM/TEM/STEM, elemental (NCHS) analysis, and four-pin electrical conductivity measurements.
- Electrochemistry used a three-electrode cell in 0.5 M H₂SO₄ with a glassy carbon working electrode (RDE at 2000 rpm), LSV at 2 mV s⁻¹, CV at 50 mV s⁻¹, EIS, a 1000-cycle stress test, and 20 h chronoamperometry; a commercial 30 wt% Pt/C was the benchmark.
Limitations
- Stated: HER activity was entirely controlled by mass-transfer limitations, so measured mass activities were not intrinsic and direct quantitative comparison with other studies is inaccurate; the influence of support porosity on intrinsic HER activity could not be quantified; the role of electrical conductivity needs further investigation; the nitrogen anchoring effect in chitosan-CA requires more in-depth study; the work is lab-scale proof-of-concept.
- Evident from the text: Pt loading accuracy was estimated at ±0.3 wt% and surface-area measurements carried relative standard deviations of 6% (CO₂) and 9% (N₂); micropore measurement of Vulcan gave noisy, undetectable results; the authors note that details of pore loss/transformation during pyrolysis remain to be clarified.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
8 Valid · 1 Not valid · 14 Not checked · 57 Own results and interpretations
Every source the paper cites for this claim was checked and supports it.
In the paper
“in this case, three successive loading and reduction steps were necessary to achieve good activities and homogeneous Pt-dispersion/sufficient Pt-amounts.”
What the sources say
- Supportedcites [47] source
The Results and Discussion section says the researchers chose three successive impregnation/reduction steps to obtain sufficient Pt loading while controlling particle morphology. The Conclusion specifies one NaBH₄ reduction followed by two H₂ reductions and reports that the resulting catalyst compared well with standard materials in oxygen-reduction activity. No page numbers are available in our copy. (LLM, conf=0.90)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
Every source the paper cites for this claim was checked and supports it.
In the paper
“Additionally, competition between HER and hydrogen oxidation reactions (HOR) occurs at low potentials due to undiffused H2 gas, leading to reduced measured mass activity.[91]”
§ 3. Results > 3.2. Electrochemical Characterization
What the sources say
- Supportedcites [91] J. Zheng, Y. Yan, B. Xu, J. Electrochem. Soc. 2015, 162, F1470. source
In “Identification of diffusion limitation in measured HER currents” (page not provided), the paper explains that slowly transported H₂ accumulates at the electrode surface, increasing the reverse HOR current and lowering the measured net-HER current, especially at low overpotentials. The section also says diffusion limitation can lead to underestimation of HOR/HER activity. The paper does not use the term “mass activity” in these passages, but the attributed mechanism and direction of the measurement error match. (LLM, conf=0.91)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“no Pt peaks were detected via XRD on most samples: this result is likely to be attributed to the low-Pt loadings and small average sizes of Pt-NPs.[70]”
§ 3. Results > 3.1. Physical Characterization of Supports and Electrocatalysts
What the sources say
- Partly supportedcites [70] sourceExperimental — accuracy not yet measured
In the rGO-supported Pt NP characterization section (pp. 29456–29466), the paper links an indistinct Pt signal in particular catalysts to small, low-density nanoparticles; it also reports low Pt content for one of them. It does not support the claim that Pt peaks were absent from most samples: the section says the other XRD patterns clearly showed characteristic Pt peaks. (LLM, conf=0.88)
hedgedstates a possible cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“However, such electrocatalysts often suffer from low stability and short durability due to the detachment and dissolution of Pt-NPs.[24–26]”
What the sources say
- Partly supportedcites [24] sourceExperimental — accuracy not yet measured
Section 4.1.1 (Platinum-based; page unavailable) says Pt-based HER catalysts face a stability challenge because Pt tends to leach or detach from its support. It does not specifically say that low Pt loading makes catalysts prone to this problem; it also describes low-loading catalysts with substantial durability. (LLM, conf=0.83)
- Not checked — no full text of the sourcecites [25] source
- Not checked — no full text of the sourcecites [26] source
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“SCD can be considered a particularly attractive technique in combination with aerogels, since the risk of meso- and micropore deformation or collapse during the impregnation of Pt precursor and during the depressurization is eliminated due to the absence of capillary forces in the supercritical state.[55–59]”
What the sources say
- Partly supportedcites [55] sourceExperimental — accuracy not yet measured
The review describes Pt-precursor adsorption onto carbon aerogels by SCD (Functional Materials for Electrochemical Applications Using Supercritical Deposition; page unavailable). It also says supercritical fluids have zero surface tension and that avoiding a phase change during depressurization enables aerogel products (Li-ion battery applications and Abstract; pages unavailable). It does not state that these properties eliminate meso- or micropore deformation or collapse during Pt impregnation and depressurization. (LLM, conf=0.84)
- Not checked — no full text of the sourcecites [56] source
- Could not verifycites [57] sourceExperimental — accuracy not yet measured
The Introduction and Conclusion describe impregnating Vulcan carbon black with a Pt precursor in supercritical CO₂, not using aerogels. Searches for capillary forces, pore collapse, and deformation found no passage stating that this process eliminates those risks during impregnation or depressurization; the References list aerogel studies but do not establish the claim. (LLM, conf=0.74)
- Not checked — no full text of the sourcecites [58] source
- Not checked — no full text of the sourcecites [59] source
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
47 more claims
Create a free account to see all 80 claims and to verify the 1 reference still open.
- Probably not a substantial claim. 19
- It may state two separate claims as one. 12
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ 3. Results > 3.1. Physical Characterization of Supports and Electrocatalysts
“Since no significant differences between supports and electrocatalysts were detected via gas physisorption and SEM imaging, we con- clude that the CA-aerogel structure was not harmed”
§ 3. Results > 3.1. Physical Characterization of Supports and Electrocatalysts
“Chitosan-CA 0 613 176 43 83 Pt-chitosan-CA 2.8 473 163 140 45”
Citations
Cites
Thommes, M., Kaneko, K., Neimark, A. V., Olivier, J. P., Rodriguez-Reinoso, F., Rouquerol, J., & Sing, K. S. W. (2015) · Pure and Applied Chemistry · doi:10.1515/pac-2014-1117 · Cited by 21,202
Hydrogen-storage materials for mobile applications
Schlapbach, L., & Züttel, A. (2001) · Nature · doi:10.1038/35104634 · Cited by 8,865
Trends in the exchange current for hydrogen evolution
Nørskov, J. K., Bligaard, T., Logadottir, A., Kitchin, J. R., Chen, J. G., Pandelov, S., & Stimming, U. (2005) · Journal of The Electrochemical Society · doi:10.1149/1.1856988 · Cited by 6,121
Heterostructures for Electrochemical Hydrogen Evolution Reaction: A Review
Zhao, G., Rui, K., Dou, S. X., & Sun, W. (2018) · Advanced Functional Materials · doi:10.1002/adfm.201803291 · Cited by 1,422
The rate of electrolytic hydrogen evolution and the heat of adsorption of hydrogen
Parsons, R. (1958) · Transactions of the Faraday Society · doi:10.1039/tf9585401053 · Cited by 1,033
Sui, S., Wang, X., Zhou, X., Su, Y., Riffat, S., & Liu, C.-J. (2017) · Journal of Materials Chemistry A · doi:10.1039/c6ta08580f · Cited by 916
Nitrogen-doped carbon materials
Inagaki, M., Toyoda, M., Soneda, Y., & Morishita, T. (2018) · Carbon · doi:10.1016/j.carbon.2018.02.024 · Cited by 867
Is There Anything Better than Pt for HER?
Hansen, J. N., Prats, H., Toudahl, K. K., Mørch Secher, N., Chan, K., Kibsgaard, J., & Chorkendorff, I. (2021) · ACS Energy Letters · doi:10.1021/acsenergylett.1c00246 · Cited by 820
Hydrogen Evolution and Oxidation: Mechanistic Studies and Material Advances
Tian, X., Zhao, P., & Sheng, W. (2019) · Advanced Materials · doi:10.1002/adma.201808066 · Cited by 751
Ott, S., Orfanidi, A., Schmies, H., Anke, B., Nong, H. N., Hübner, J., Gernert, U., Gliech, M., Lerch, M., & Strasser, P. (2020) · Nature Materials · doi:10.1038/s41563-019-0487-0 · Cited by 727
Research works printed but not linked: 2
- Gielen D., 2019, Int. Renewable Energy Agency
- Henning K. D., 2021, Ind. Carbon Graphite Mater., Volume II, 2, 491
Cited by
Cha, S., Choi, M. Y., Kim, M. J., Sim, S. B., Haizan, I., & Choi, J. (2025) · Biosensors · doi:10.3390/bios15060380 · Cited by 32
Abdelwahab, A., Humaidi, J. R., Abdulaziz, F., Alanazi, A. A., Alenezi, K. M., & Farghali, A. A. (2026) · Nanoscale Advances · doi:10.1039/d5na00946d · Cited by 5
Pein, P. S., Alsuhile, A. A. A. M., Penner, S., Mohammadi, A., Zickler, G. A., Almohammad, A. A., Baron, F., Kirstein, M., Erkey, C., Smirnova, I. V., et al. (2026) · Small · doi:10.1002/smll.202512049 · Cited by 2
Self-citationNizameeva, G., Lebedeva, E. M., Vorobieva, V. V., Soloviev, E. A., Sarimov, R. M., & Nizameev, I. R. (2026) · Molecules · doi:10.3390/molecules31010150 · Cited by 3
Li, X., Bian, J., Chen, S., Li, N., & Zhan, G. (2026) · Chemical Engineering Science · doi:10.1016/j.ces.2026.124395 · Cited by 1
Metadata
- Authors
- Alsuhile, A., Pein, P. S., Barım, Ş. B., Bozbağ, S. E., Smirnova, I., Erkey, C., & Schroeter, B.
- Affiliations
- Koç University (TR)
- Hamburg University of Technology (DE)
- United Nations University Institute for Water, Environment, and Health (CA)
- Corresponding author
- Schroeter, Baldur
- Venue
- Advanced Energy and Sustainability Research
- Publisher
- Wiley
- Published
- 2025-03-02
- Volume
- 6
- Issue
- 8
- ISSN
- 2699-9412 (ISSN-L)
- OpenAlex
- W4408333127
- Semantic Scholar
- 1fc8724929c100251dcbb769fb6905ad9ba19e46
- Cited by
- 8
- References
- 94
- Citations by year
- 2026: 6 · 2025: 2
- FWCI
- 1.10
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Advanced Energy and Sustainability Research (publishedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- TUHH Open Research (cc-by)
- Funders
- Bundesministerium für Wirtschaft und Klimaschutz (KK5440301ZG1)
- Topics
- Physical Sciences › Energy › Renewable Energy, Sustainability and the Environment › Electrocatalysts for Energy Conversion
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Fuel Cells and Related Materials
- Physical Sciences › Materials Science › Materials Chemistry › Catalytic Processes in Materials Science
- Keywords
- platinum electrocatalysts, carbon aerogels, hydrogen evolution reaction, cellulose aerogels, chitosan aerogel, multiscale porosity, platinum nanoparticles, catalyst stability, green hydrogen production, Vulcan XC-72R
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-11, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-11 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Synthesis of Pt Carbon Aerogel Electrocatalysts with Multiscale Porosity Derived from Cellulose and Chitosan Biopolymer Aerogels via Supercritical Deposition for Hydrogen Evolution Reaction. https://app.cochat.ai/papers/10.1002/aesr.202400433
- The paper
- Alsuhile, A., Pein, P. S., Barım, Ş. B., Bozbağ, S. E., Smirnova, I., Erkey, C., & Schroeter, B. (2025). Synthesis of Pt Carbon Aerogel Electrocatalysts with Multiscale Porosity Derived from Cellulose and Chitosan Biopolymer Aerogels via Supercritical Deposition for Hydrogen Evolution Reaction. Advanced Energy and Sustainability Research. https://doi.org/10.1002/aesr.202400433
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.