The DOI matches its Crossref record.
New Approaches for High Energy Density Lithium–Sulfur Battery Cathodes
Abstract
The goal of replacing combustion engines or reducing their use presents a daunting problem for society. Current lithium-ion technologies provide a stepping stone for this dramatic but inevitable change. However, the theoretical gravimetric capacity (∼300 mA h g(-1)) is too low to overcome the problems of limited range in electric vehicles, and their cost is too high to sustain the commercial viability of electrified transportation. Sulfur is the one of the most promising next generation cathode materials. Since the 1960s, researchers have studied sulfur as a cathode, but only recently have great strides been made in preparing viable composites that can be used commercially. Sulfur batteries implement inexpensive, earth-abundant elements at the cathode while offering up to a five-fold increase in energy density compared with present Li-ion batteries. Over the past few years, researchers have come closer to solving the challenges associated with the sulfur cathode. Using carbon or conducting polymers, researchers have wired up sulfur, an excellent insulator, successfully. These conductive hosts also function to encapsulate the active sulfur mass upon reduction/oxidation when highly soluble lithium polysulfides are formed. These soluble discharge products remain a crux of the Li-S cell and need to be contained in order to increase cycle life and capacity retention. The use of mesoporous carbons and tailored designs featuring porous carbon hollow spheres have led to highly stable discharge capacities greater than 900 mA h g(-1) over 100 cycles. In an attempt to fully limit polysulfide dissolution, methods that rely on coating carbon/sulfur composites with polymers have led to surprisingly stable capacities (∼90% of initial capacity retained). Additives will also play an important role in sulfur electrode design. For example, small fractions (> 3 wt%) of porous silica or titania effectively act as polysulfide reservoirs, decreasing their concentration in the electrolyte and leading to a higher utilization of sulfur and increased capacities.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cited by
Rechargeable Lithium–Sulfur Batteries
Manthiram, A., Fu, Y., Chung, S.-H., Zu, C., & Su, Y.-S. (2014) · Chemical Reviews · doi:10.1021/cr500062v · Cited by 4,665
Lithium–Sulfur Batteries: Electrochemistry, Materials, and Prospects
Yin, Y., Xin, S., Guo, Y., & Wan, L. (2013) · Angewandte Chemie International Edition · doi:10.1002/anie.201304762 · Cited by 2,707
Designing high-energy lithium–sulfur batteries
Seh, Z. W., Sun, Y., Zhang, Q., & Cui, Y. (2016) · Chemical Society Reviews · doi:10.1039/c5cs00410a · Cited by 2,573
A new class of Solvent-in-Salt electrolyte for high-energy rechargeable metallic lithium batteries
Suo, L., Hu, Y.-S., Li, H., Armand, M., & Chen, L. (2013) · Nature Communications · doi:10.1038/ncomms2513 · Cited by 2,314
A highly efficient polysulfide mediator for lithium–sulfur batteries
Liang, X., Hart, C., Pang, Q., Garsuch, A., Weiss, T., & Nazar, L. F. (2015) · Nature Communications · doi:10.1038/ncomms6682 · Cited by 2,062
Self-citationReview on High‐Loading and High‐Energy Lithium–Sulfur Batteries
Peng, H., Huang, J., Cheng, X., & Zhang, Q. (2017) · Advanced Energy Materials · doi:10.1002/aenm.201700260 · Cited by 1,746
Lithium–Sulfur Batteries: Progress and Prospects
Manthiram, A., Chung, S., & Zu, C. (2015) · Advanced Materials · doi:10.1002/adma.201405115 · Cited by 1,620
Nanostructured Metal Oxides and Sulfides for Lithium–Sulfur Batteries
Liu, X., Huang, J., Zhang, Q., & Mai, L. (2017) · Advanced Materials · doi:10.1002/adma.201601759 · Cited by 1,616
The synergetic effect of lithium polysulfide and lithium nitrate to prevent lithium dendrite growth
Li, W., Yao, H., Yan, K., Zheng, G., Liang, Z., Chiang, Y.-M., & Cui, Y. (2015) · Nature Communications · doi:10.1038/ncomms8436 · Cited by 1,540
Catalytic oxidation of Li 2 S on the surface of metal sulfides for Li−S batteries
Zhou, G., Tian, H., Jin, Y., Tao, X., Liu, B., Zhang, R., Seh, Z. W., Zhuo, D., Liu, Y., Sun, J., et al. (2017) · Proceedings of the National Academy of Sciences · doi:10.1073/pnas.1615837114 · Cited by 1,278
Advanced lightweight materials for Automobiles: A review
Zhang, W., & Xu, J. (2022) · Materials & Design · doi:10.1016/j.matdes.2022.110994 · Cited by 1,147
Defect Engineering on Electrode Materials for Rechargeable Batteries
Zhang, Y., Tao, L., Xie, C., Wang, D., Zou, Y., Chen, R., Wang, Y., Jia, C., & Wang, S. (2020) · Advanced Materials · doi:10.1002/adma.201905923 · Cited by 1,019
Mechanism and Kinetics of Li2S Precipitation in Lithium–Sulfur Batteries
Fan, F. Y., Carter, W. C., & Chiang, Y. (2015) · Advanced Materials · doi:10.1002/adma.201501559 · Cited by 987
Chen, H., Ling, M., Hencz, L., Ling, H. Y., Li, G., Lin, Z., Liu, G., & Zhang, S. (2018) · Chemical Reviews · doi:10.1021/acs.chemrev.8b00241 · Cited by 958
Sodium Metal Anodes: Emerging Solutions to Dendrite Growth
Lee, B., Paek, E., Mitlin, D., & Lee, S. W. (2019) · Chemical Reviews · doi:10.1021/acs.chemrev.8b00642 · Cited by 940
Advances in Lithium–Sulfur Batteries: From Academic Research to Commercial Viability
Chen, Y., Wang, T., Tian, H., Su, D., Zhang, Q., & Wang, G. (2021) · Advanced Materials · doi:10.1002/adma.202003666 · Cited by 870
Pang, Q., Tang, J., Huang, H., Liang, X., Hart, C., Tam, K. C., & Nazar, L. F. (2015) · Advanced Materials · doi:10.1002/adma.201502467 · Cited by 780
Self-citationInterwoven MXene Nanosheet/Carbon‐Nanotube Composites as Li–S Cathode Hosts
Liang, X., Rangom, Y., Kwok, C. Y., Pang, Q., & Nazar, L. F. (2017) · Advanced Materials · doi:10.1002/adma.201603040 · Cited by 759
Self-citationZheng, G., Zhang, Q., Cha, J. J., Yang, Y., Li, W., Seh, Z. W., & Cui, Y. (2013) · Nano Letters · doi:10.1021/nl304795g · Cited by 705
Tao, X., Wang, J., Ying, Z., Cai, Q., Zheng, G., Gan, Y., Huang, H., Xia, Y., Liang, C., Zhang, W., et al. (2014) · Nano Letters · doi:10.1021/nl502331f · Cited by 687
Huang, J.-Q., Zhang, Q., & Wei, F. (2015) · Energy Storage Materials · doi:10.1016/j.ensm.2015.09.008 · Cited by 665
Li, Z., Wu, H. B., & (David) Lou, X. W. (2016) · Energy & Environmental Science · doi:10.1039/c6ee02364a · Cited by 654
Zhao, C., Xu, G.-L., Yu, Z., Zhang, L., Hwang, I., Mo, Y.-X., Ren, Y., Cheng, L., Sun, C.-J., Ren, Y., et al. (2021) · Nature Nanotechnology · doi:10.1038/s41565-020-00797-w · Cited by 650
A Flexible Sulfur‐Graphene‐Polypropylene Separator Integrated Electrode for Advanced Li–S Batteries
Zhou, G., Li, L., Wang, D., Shan, X., Pei, S., Li, F., & Cheng, H. (2015) · Advanced Materials · doi:10.1002/adma.201404210 · Cited by 590
Li, Z., Jiang, Y., Yuan, L., Yi, Z., Wu, C., Liu, Y., Strasser, P., & Huang, Y. (2014) · ACS Nano · doi:10.1021/nn503220h · Cited by 590
Zhang, J., Hu, H., Li, Z., & Lou, X. W. (. (2016) · Angewandte Chemie International Edition · doi:10.1002/anie.201511632 · Cited by 560
Peng, H., Huang, J., Zhao, M., Zhang, Q., Cheng, X., Liu, X., Qian, W., & Wei, F. (2014) · Advanced Functional Materials · doi:10.1002/adfm.201303296 · Cited by 552
Yao, H., Yan, K., Li, W., Zheng, G., Kong, D., Seh, Z. W., Narasimhan, V. K., Liang, Z., & Cui, Y. (2014) · Energy Environ. Sci. · doi:10.1039/c4ee01377h · Cited by 526
Applications of Phosphorene and Black Phosphorus in Energy Conversion and Storage Devices
Pang, J., Bachmatiuk, A., Yin, Y., Trzebicka, B., Zhao, L., Fu, L., Mendes, R. G., Gemming, T., Liu, Z., & Rummeli, M. H. (2018) · Advanced Energy Materials · doi:10.1002/aenm.201702093 · Cited by 518
Progress in Mechanistic Understanding and Characterization Techniques of Li‐S Batteries
Xu, R., Lu, J., & Amine, K. (2015) · Advanced Energy Materials · doi:10.1002/aenm.201500408 · Cited by 507
Zhou, G., Zhao, Y., & Manthiram, A. (2015) · Advanced Energy Materials · doi:10.1002/aenm.201402263 · Cited by 502
Anodes for Rechargeable Lithium‐Sulfur Batteries
Cao, R., Xu, W., Lv, D., Xiao, J., & Zhang, J. (2015) · Advanced Energy Materials · doi:10.1002/aenm.201402273 · Cited by 502
Li, Z., Yuan, L., Yi, Z., Sun, Y., Liu, Y., Jiang, Y., Shen, Y., Xin, Y., Zhang, Z., & Huang, Y. (2014) · Advanced Energy Materials · doi:10.1002/aenm.201301473 · Cited by 481
Progress on the Critical Parameters for Lithium–Sulfur Batteries to be Practically Viable
Chung, S., Chang, C., & Manthiram, A. (2018) · Advanced Functional Materials · doi:10.1002/adfm.201801188 · Cited by 477
Li, Z., Li, C., Ge, X., Ma, J., Zhang, Z., Li, Q., Wang, C., & Yin, L. (2016) · Nano Energy · doi:10.1016/j.nanoen.2016.02.049 · Cited by 449
Griebel, J. J., Glass, R. S., Char, K., & Pyun, J. (2016) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2016.04.003 · Cited by 446
Nanowires for Electrochemical Energy Storage
Zhou, G., Xu, L., Hu, G., Mai, L., & Cui, Y. (2019) · Chemical Reviews · doi:10.1021/acs.chemrev.9b00326 · Cited by 439
Hierarchically structured porous materials: synthesis strategies and applications in energy storage
Wu, L., Li, Y., Fu, Z., & Su, B.-L. (2020) · National Science Review · doi:10.1093/nsr/nwaa183 · Cited by 438
Recent advances in lithium–sulfur batteries
Chen, L., & Shaw, L. L. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2014.05.111 · Cited by 432
A graphene-like metallic cathode host for long-life and high-loading lithium–sulfur batteries
Pang, Q., Kundu, D., & Nazar, L. F. (2016) · Materials Horizons · doi:10.1039/c5mh00246j · Cited by 424
Self-citationCritical Challenges in Rechargeable Aprotic Li–O2 Batteries
Feng, N., He, P., & Zhou, H. (2016) · Advanced Energy Materials · doi:10.1002/aenm.201502303 · Cited by 423
Ziegler, C., Wolf, A., Liu, W., Herrmann, A., Gaponik, N., & Eychmüller, A. (2017) · Angewandte Chemie International Edition · doi:10.1002/anie.201611552 · Cited by 419
Al2O3-coated porous separator for enhanced electrochemical performance of lithium sulfur batteries
Zhang, Z., Lai, Y., Zhang, Z., Zhang, K., & Li, J. (2014) · Electrochimica Acta · doi:10.1016/j.electacta.2014.02.077 · Cited by 418
Carbon Materials for Lithium Sulfur Batteries—Ten Critical Questions
Borchardt, L., Oschatz, M., & Kaskel, S. (2016) · Chemistry – A European Journal · doi:10.1002/chem.201600040 · Cited by 414
Pang, Q., & Nazar, L. F. (2016) · ACS Nano · doi:10.1021/acsnano.5b07347 · Cited by 411
Self-citationStructural Design of Lithium–Sulfur Batteries: From Fundamental Research to Practical Application
Yang, X., Li, X., Adair, K., Zhang, H., & Sun, X. (2018) · Electrochemical Energy Reviews · doi:10.1007/s41918-018-0010-3 · Cited by 411
Progress Towards Commercially Viable Li–S Battery Cells
Urbonaite, S., Poux, T., & Novák, P. (2015) · Advanced Energy Materials · doi:10.1002/aenm.201500118 · Cited by 406
Yao, H., Zheng, G., Hsu, P.-C., Kong, D., Cha, J. J., Li, W., Seh, Z. W., McDowell, M. T., Yan, K., Liang, Z., et al. (2014) · Nature Communications · doi:10.1038/ncomms4943 · Cited by 398
Peng, H., Hou, T., Zhang, Q., Huang, J., Cheng, X., Guo, M., Yuan, Z., He, L., & Wei, F. (2014) · Advanced Materials Interfaces · doi:10.1002/admi.201400227 · Cited by 393
High-Performance Li–S Batteries with an Ultra-lightweight MWCNT-Coated Separator
Chung, S.-H., & Manthiram, A. (2014) · The Journal of Physical Chemistry Letters · doi:10.1021/jz5006913 · Cited by 393
Transition Metal Dichalcogenide Atomic Layers for Lithium Polysulfides Electrocatalysis
Babu, G., Masurkar, N., Al Salem, H., & Arava, L. M. R. (2017) · Journal of the American Chemical Society · doi:10.1021/jacs.6b08681 · Cited by 386
Graphene‐Based Nanocomposites for Energy Storage
Ji, L., Meduri, P., Agubra, V., Xiao, X., & Alcoutlabi, M. (2016) · Advanced Energy Materials · doi:10.1002/aenm.201502159 · Cited by 385
Zhou, W., Xiao, X., Cai, M., & Yang, L. (2014) · Nano Letters · doi:10.1021/nl502238b · Cited by 382
Multifunctional Co3S4@sulfur nanotubes for enhanced lithium-sulfur battery performance
Pu, J., Shen, Z., Zheng, J., Wu, W., Zhu, C., Zhou, Q., Zhang, H., & Pan, F. (2017) · Nano Energy · doi:10.1016/j.nanoen.2017.05.009 · Cited by 369
Interfacial Assembly and Applications of Functional Mesoporous Materials
Duan, L., Wang, C., Zhang, W., Ma, B., Deng, Y., Li, W., & Zhao, D. (2021) · Chemical Reviews · doi:10.1021/acs.chemrev.1c00236 · Cited by 368
Chung, S., & Manthiram, A. (2014) · Advanced Materials · doi:10.1002/adma.201402893 · Cited by 364
Wang, X., Li, G., Li, J., Zhang, Y., Wook, A., Yu, A., & Chen, Z. (2016) · Energy & Environmental Science · doi:10.1039/c6ee00194g · Cited by 360
Strubel, P., Thieme, S., Biemelt, T., Helmer, A., Oschatz, M., Brückner, J., Althues, H., & Kaskel, S. (2015) · Advanced Functional Materials · doi:10.1002/adfm.201402768 · Cited by 352
Exploiting a robust biopolymer network binder for an ultrahigh-areal-capacity Li–S battery
Liu, J., Galpaya, D. G. D., Yan, L., Sun, M., Lin, Z., Yan, C., Liang, C., & Zhang, S. (2017) · Energy & Environmental Science · doi:10.1039/c6ee03033e · Cited by 347
Cao, J., Chen, C., Zhao, Q., Zhang, N., Lu, Q., Wang, X., Niu, Z., & Chen, J. (2016) · Advanced Materials · doi:10.1002/adma.201602262 · Cited by 339
In Situ Raman Spectroscopy of Sulfur Speciation in Lithium–Sulfur Batteries
Wu, H.-L., Huff, L. A., & Gewirth, A. A. (2015) · ACS Applied Materials & Interfaces · doi:10.1021/am5072942 · Cited by 338
Sulfur‐Based Composite Cathode Materials for High‐Energy Rechargeable Lithium Batteries
Wang, J., He, Y., & Yang, J. (2015) · Advanced Materials · doi:10.1002/adma.201402569 · Cited by 331
Three-dimensional ordered porous electrode materials for electrochemical energy storage
Liu, Z., Yuan, X., Zhang, S., Wang, J., Huang, Q., Yu, N., Zhu, Y., Fu, L., Wang, F., Chen, Y., et al. (2019) · NPG Asia Materials · doi:10.1038/s41427-019-0112-3 · Cited by 328
Pang, Q., Liang, X., Kwok, C. Y., & Nazar, L. F. (2015) · Journal of The Electrochemical Society · doi:10.1149/2.0171514jes · Cited by 323
Self-citationDesign of Complex Nanomaterials for Energy Storage: Past Success and Future Opportunity
Liu, Y., Zhou, G., Liu, K., & Cui, Y. (2017) · Accounts of Chemical Research · doi:10.1021/acs.accounts.7b00450 · Cited by 323
Zhou, F., Li, Z., Luo, X., Wu, T., Jiang, B., Lu, L.-L., Yao, H.-B., Antonietti, M., & Yu, S.-H. (2018) · Nano Letters · doi:10.1021/acs.nanolett.7b04505 · Cited by 316
Nazar, L. F., Cuisinier, M., & Pang, Q. (2014) · MRS Bulletin · doi:10.1557/mrs.2014.86 · Cited by 314
Self-citationWang, W., Cao, Z., Elia, G. A., Wu, Y., Wahyudi, W., Abou-Hamad, E., Emwas, A.-H., Cavallo, L., Li, L.-J., & Ming, J. (2018) · ACS Energy Letters · doi:10.1021/acsenergylett.8b01945 · Cited by 312
Confined Sulfur in Microporous Carbon Renders Superior Cycling Stability in Li/S Batteries
Xu, Y., Wen, Y., Zhu, Y., Gaskell, K., Cychosz, K. A., Eichhorn, B., Xu, K., & Wang, C. (2015) · Advanced Functional Materials · doi:10.1002/adfm.201500983 · Cited by 311
Insight into the Effect of Boron Doping on Sulfur/Carbon Cathode in Lithium–Sulfur Batteries
Yang, C.-P., Yin, Y.-X., Ye, H., Jiang, K.-C., Zhang, J., & Guo, Y.-G. (2014) · ACS Applied Materials & Interfaces · doi:10.1021/am501627f · Cited by 310
Two‐dimensional MXenes for lithium‐sulfur batteries
Zhang, C. (., Cui, L., Abdolhosseinzadeh, S., & Heier, J. (2020) · InfoMat · doi:10.1002/inf2.12080 · Cited by 308
Historical development and novel concepts on electrolytes for aqueous rechargeable batteries
Chen, S., Zhang, M., Zou, P., Sun, B., & Tao, S. (2022) · Energy & Environmental Science · doi:10.1039/d2ee00004k · Cited by 308
Rana, M., Ahad, S. A., Li, M., Luo, B., Wang, L., Gentle, I., & Knibbe, R. (2019) · Energy Storage Materials · doi:10.1016/j.ensm.2018.12.024 · Cited by 301
Nanostructured positive electrode materials for post-lithium ion batteries
Wang, F., Wu, X., Li, C., Zhu, Y., Fu, L., Wu, Y., & Liu, X. (2016) · Energy & Environmental Science · doi:10.1039/c6ee02070d · Cited by 293
Rechargeable Metal-Sulfur Batteries: Key Materials to Mechanisms
Yao, W., Liao, K., Lai, T., Sul, H., & Manthiram, A. (2024) · Chemical Reviews · doi:10.1021/acs.chemrev.3c00919 · Cited by 287
Shrivastav, V., Sundriyal, S., Goel, P., Kaur, H., Tuteja, S. K., Vikrant, K., Kim, K.-H., Tiwari, U. K., & Deep, A. (2019) · Coordination Chemistry Reviews · doi:10.1016/j.ccr.2019.05.006 · Cited by 284
Confined selenium within porous carbon nanospheres as cathode for advanced Li–Se batteries
Li, Z., Yuan, L., Yi, Z., Liu, Y., & Huang, Y. (2014) · Nano Energy · doi:10.1016/j.nanoen.2014.07.012 · Cited by 284
Recent Advances in Lithium Sulfide Cathode Materials and Their Use in Lithium Sulfur Batteries
Son, Y., Lee, J., Son, Y., Jang, J., & Cho, J. (2015) · Advanced Energy Materials · doi:10.1002/aenm.201500110 · Cited by 283
Durable Carbon-Coated Li2S Core–Shell Spheres for High Performance Lithium/Sulfur Cells
Nan, C., Lin, Z., Liao, H., Song, M.-K., Li, Y., & Cairns, E. J. (2014) · Journal of the American Chemical Society · doi:10.1021/ja412943h · Cited by 282
Defect Engineering for Expediting Li–S Chemistry: Strategies, Mechanisms, and Perspectives
Shi, Z., Li, M., Sun, J., & Chen, Z. (2021) · Advanced Energy Materials · doi:10.1002/aenm.202100332 · Cited by 269
Li, G., Wang, X., Seo, M. H., Li, M., Ma, L., Yuan, Y., Wu, T., Yu, A., Wang, S., Lu, J., et al. (2018) · Nature Communications · doi:10.1038/s41467-018-03116-z · Cited by 267
Engineering Strategies for Suppressing the Shuttle Effect in Lithium–Sulfur Batteries
Li, J., Gao, L., Pan, F., Gong, C., Sun, L., Gao, H., Zhang, J., Zhao, Y., Wang, G., & Liu, H. (2024) · Nano-Micro Letters · doi:10.1007/s40820-023-01223-1 · Cited by 267
Zhou, G., Zhao, Y., Zu, C., & Manthiram, A. (2015) · Nano Energy · doi:10.1016/j.nanoen.2014.12.029 · Cited by 267
Sun, Q., He, B., Zhang, X.-Q., & Lu, A.-H. (2015) · ACS Nano · doi:10.1021/acsnano.5b03488 · Cited by 265
Elemental Selenium for Electrochemical Energy Storage
Yang, C.-P., Yin, Y.-X., & Guo, Y.-G. (2015) · The Journal of Physical Chemistry Letters · doi:10.1021/jz502405h · Cited by 263
Wang, C., Su, K., Wan, W., Guo, H., Zhou, H., Chen, J., Zhang, X., & Huang, Y. (2014) · J. Mater. Chem. A · doi:10.1039/c3ta14921h · Cited by 263
Hierarchical carbon nanocages confining high-loading sulfur for high-rate lithium–sulfur batteries
Lyu, Z., Xu, D., Yang, L., Che, R., Feng, R., Zhao, J., Li, Y., Wu, Q., Wang, X., & Hu, Z. (2015) · Nano Energy · doi:10.1016/j.nanoen.2015.01.033 · Cited by 258
Cobalt oxide-based nanoarchitectures for electrochemical energy applications
Mei, J., Liao, T., Ayoko, G. A., Bell, J., & Sun, Z. (2019) · Progress in Materials Science · doi:10.1016/j.pmatsci.2019.03.001 · Cited by 256
Three-Dimensional Growth of Li2S in Lithium–Sulfur Batteries Promoted by a Redox Mediator
Gerber, L. C. H., Frischmann, P. D., Fan, F. Y., Doris, S. E., Qu, X., Scheuermann, A. M., Persson, K., Chiang, Y.-M., & Helms, B. A. (2016) · Nano Letters · doi:10.1021/acs.nanolett.5b04189 · Cited by 255
Understanding inks for porous-electrode formation
Hatzell, K. B., Dixit, M. B., Berlinger, S. A., & Weber, A. Z. (2017) · J. Mater. Chem. A · doi:10.1039/c7ta07255d · Cited by 97
Kim, P. J., Fontecha, H. D., Kim, K., & Pol, V. G. (2018) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.8b03959 · Cited by 71
Metadata
- Authors
- Evers, S., & Nazar, L. F.
- Venue
- Accounts of Chemical Research
- Publisher
- American Chemical Society (ACS)
- Published
- 2012-10-10
- Volume
- 46
- Issue
- 5
- Pages
- 1135-1143
- ISSN
- 0001-4842 (ISSN-L)
- 1520-4898
- OpenAlex
- W2054984038
- Cited by
- 1,324
- References
- 0
- FWCI
- 55.96
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.