Preparation of Microporous Carbon from Sargassum horneri by Hydrothermal Carbonization and KOH Activation for CO2 Capture
Open accessThe DOI matches its Crossref record; 68 of the 68 references it cites were found in a registry or an index; 6 of the 49 sources its claims cite were checked for support.
Abstract
High-performance microporous activated carbon (AHC) for CO 2 capture was prepared from an emerging marine pollutant, Sargassum horneri , via hydrothermal carbonization (HTC) and KOH activation. The as-synthesized carbon material was characterized by N 2 sorption-desorption measurement, TGA, SEM, XRD, FTIR, and elemental analysis. Impressively, the activated carbon exhibited high specific surface area (1221 m 2 /g), narrow distributed micropores (∼0.50 nm), and a relatively high nitrogen content (3.56 wt.%), which endowed this carbon material high CO 2 uptake of 101.7 mg/g at 30°C and 1 bar. Moreover, the carbon material showed highly stable CO 2 adsorption capacity and easy regeneration over four adsorption-desorption cycles. Two kinetic models were employed in this work and found that the pseudo-first-order kinetic model ( R 2 = 0.99) provided the best description. In addition, the high CO 2 uptake is mainly attributed to the presence of abundant narrow microporous. The macroporous structure of hydrochar (HC) played an important role in the production of microporous carbon with high adsorption properties. This work provides an efficient strategy for preparing microporous activated carbon from Sargassum horneri , and AHC is a promising candidate acting as an efficient CO 2 adsorbent for further industrial application.
Overview
CoChat Summary
## TL;DR
The paper reports a method to turn the marine waste alga *Sargassum horneri* into microporous activated carbon for CO2 capture using hydrothermal carbonization followed by KOH activation. The best adsorbent achieved 101.7 mg/g CO2 uptake at 30 °C and 1 bar, with rapid adsorption and stable regeneration over four cycles.
## Key findings
- Hydrothermal carbonization of *S. horneri* at 180 °C for 2 h produced hydrochar (HC) with 65.0% carbon recovery and 51.4% yield; KOH activation then produced activated hydrochar (AHC).
- AHC had a BET surface area of 1221 m²/g and abundant narrow micropores of about 0.50 nm; HC had only 26.64 m²/g BET surface area and negligible micropore volume.
- CO2 uptake of AHC was 101.7 mg/g at 30 °C, 92 mg/g at 45 °C, and 54 mg/g at 60 °C at 1 bar; HC reached 36, 23, and 17 mg/g under the same conditions.
- The pseudo-first-order kinetic model fit CO2 adsorption better than the pseudo-second-order model, with R² = 0.99218 and error = 3.57%; about 70% of total CO2 uptake occurred within 6 min.
- In regeneration tests, more than 94% of adsorbed CO2 was desorbed within 3 min, and the adsorbent retained ~99% of its initial capacity over four adsorption-desorption cycles.
## Methods
- The study prepared hydrochar by hydrothermal treatment of *S. horneri* mixed with Fe(NH4)2(SO4)2·6H2O catalyst at 180 °C for 2 h, then activated the hydrochar with KOH at 600 °C for 2 h under N2.
- The sample characterization used SEM, TGA/DTG, N2 sorption-desorption, CO2 adsorption, FTIR, XRD, and elemental analysis.
- CO2 adsorption was measured on 10 mg samples in a thermogravimetric analyzer at 30, 45, and 60 °C under 1 bar, and adsorption-desorption cycling was repeated 4 times; kinetics were fitted with pseudo-first-order and pseudo-second-order models.
## Limitations
- The paper states that the data used to support the findings are included within the article, so no external dataset is provided; this limits independent reanalysis.
- The experiments appear to be laboratory-scale and focus on one biomass precursor and one activation route; the text does not report pilot-scale or real-flue-gas testing (evident from the paper text).
- The paper does not state major experimental limitations beyond the above.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
6 Valid · 0 Not valid · 24 Not checked · 62 Own results and interpretations
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“the cellulose and lignin significantly decomposes under hydrothermal conditions above approximately 200 ° C [57, 58].”
What the sources say
- Partly supportedcites [57] sourceExperimental — accuracy not yet measured
Section 2.2 (Hydrothermal Carbonization; page not available) says cellulose is hydrolyzed under hydrothermal conditions, but lignin undergoes only partial hydrolysis and decomposes less strongly than cellulose. It does not establish approximately 200 °C as a threshold for significant decomposition of both; the temperature discussion in Section 2.1 concerns pyrolysis, not hydrothermal treatment. (LLM, conf=0.86)
- Not checked — no full text of the sourcecites [58] source
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Cui et al. [37] reported that metal ions, such as iron ions, could effectively accelerate the hydrothermal carbonization process, which shortened the reaction time to some hours.”
What the sources say
- Partly supportedcites [37] sourceExperimental — accuracy not yet measured
The main text says metal ions can accelerate hydrothermal carbonization of starch and reports that iron ions catalyze the process. The Experimental Section describes an iron-ion reaction lasting 12 hours, but our copy does not establish that iron ions shortened the reaction time to that duration compared with a reaction without them. (LLM, conf=0.86)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“narrow distributed micropores ( ∼ 0.50 nm)”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“the activated carbon exhibited high specific surface area (1221 m 2 /g)”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“high CO2 uptake of 101.7 mg/g at 30 ° C and 1 bar.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
51 more claims
Create a free account to see all 92 claims and every source verdict.
- Probably not a substantial claim. 13
- It may state two separate claims as one. 28
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“Pyrolyzed algal biochars typically exhibit a moderate to high carbon content and a porous structure but require activation treatments (e.g., KOH or ZnCl 2 ) to enhance their surface area and adsorption capabilities.”
From Algal-Based Carbonaceous Materials for Environmental Remediation: Advances in Wastewater Treatment, Carbon Sequestration, and Biofuel Applications (2025) · cites this paper as [6]
Experimental — accuracy not yet measuredThe source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“However, its surface area (1-50 m 2 /g) is often smaller than that of terrestrial biochars, necessitating activation processes, such as KOH or ZnCl 2 treatments, to enhance adsorptive performance [5,6].”
From Algal-Based Carbonaceous Materials for Environmental Remediation: Advances in Wastewater Treatment, Carbon Sequestration, and Biofuel Applications (2025) · cites this paper as [6]
Experimental — accuracy not yet measuredIn the citing paper
“Pyrolyzed algal biochars typically exhibit a moderate to high carbon content and a porous structure but require activation treatments (e.g., KOH or ZnCl 2 ) to enhance their surface area and adsorption capabilities.”
From Algal-Based Carbonaceous Materials for Environmental Remediation: Advances in Wastewater Treatment, Carbon Sequestration, and Biofuel Applications (2025) · cites this paper as [6]
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ 3. Results and Discussion
“| AHC | 1221 | 0.58 | 0.38 | 2.16 |”
§ 3. Results and Discussion
“The developed porosity can be achieved through adjusting the activation conditions [24]. Compared with HC, AHC exhibited higher specific surface area (1221 m 2 /g), micropores volume (0.38 m 3 /g), and narrower distributed micropores ( ∼ 0.50 nm), indicating that the KOH activation contributes the most to the formation of micropore structures [60].”
Citations
Cites
The production of carbon materials by hydrothermal carbonization of cellulose
Sevilla, M., & Fuertes, A. B. (2009) · Carbon · doi:10.1016/j.carbon.2009.04.026 · Cited by 2,021 · cited 1×
“*e absorption bands observed in the range of 1000–1450 cm represented the C-O stretching vibrations [53].”
BackgroundFunke, A., & Ziegler, F. (2010) · Biofuels Bioproducts and Biorefining · doi:10.1002/bbb.198 · Cited by 2,001 · cited 1×
“Hemicellulose is easy to liquefy and degrades into smaller molecules under mild hydrothermal temperature (180°C) [56], while the cellulose and lignin significantly decomposes under hydrothermal conditions above approximately 200°C [57, 58].”
BackgroundKambo, H. S., & Dutta, A. (2015) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2015.01.050 · Cited by 1,746 · cited 1×
“Hydrothermal carbonization (HTC) is a thermochemical conversion process where an organic substrate is converted into a solid product enriched in carbon content in the presence of water [16].”
BackgroundChemistry and materials options of sustainable carbon materials made by hydrothermal carbonization
Titirici, M.-M., & Antonietti, M. (2010) · Chem. Soc. Rev. · doi:10.1039/b819318p · Cited by 1,255 · cited 4×
“*e thermogravimetric analysis (TGA), derivative thermogravimetry (DTG), and CO2 adsorption experiments were performed on a thermogravimetric analyzer (NETZSCH TG 209 F3 Tarsus, Germany).”
BackgroundInfluentialSustainable porous carbons with a superior performance for CO2 capture
Sevilla, M., & Fuertes, A. B. (2011) · Energy & Environmental Science · doi:10.1039/c0ee00784f · Cited by 1,088 · cited 2×
“*is is due to the fact that the interaction energy of CO2molecules and adsorbent can be greatly enhanced due to the overlapping of the potential fields from the adjacent walls when the adsorption occurs in narrow micropores [21, 24].”
BackgroundGreen and golden seaweed tides on the rise
Smetacek, V., & Zingone, A. (2013) · Nature · doi:10.1038/nature12860 · Cited by 949 · cited 2×
“horneri golden tides brought its detrimental side to tourism-based economics, coastal ecosystems, ocean transportation, and water quality [5, 6].”
BackgroundHydrothermal degradation of polymers derived from plants
Bobleter, O. (1994) · Progress in Polymer Science · doi:10.1016/0079-6700(94)90033-7 · Cited by 889 · cited 1×
“Hemicellulose is easy to liquefy and degrades into smaller molecules under mild hydrothermal temperature (180°C) [56], while the cellulose and lignin significantly decomposes under hydrothermal conditions above approximately 200°C [57, 58].”
BackgroundGraphical-statistical method for the study of structure and reaction processes of coal
Krevelen, V. (1950) · Fuel · Cited by 784
Effect of pore size on carbon dioxide sorption by carbide derived carbon
Presser, V., McDonough, J., Yeon, S.-H., & Gogotsi, Y. (2011) · Energy & Environmental Science · doi:10.1039/c1ee01176f · Cited by 668 · cited 1×
“8 nm played a key role in determining CO2 capture on N-free carbide-derived carbons at 1 bar [22].”
BackgroundRole of chemical activation in the development of carbon porosity
Molina-Sabio, M., & Rodrı́guez-Reinoso, F. (2004) · Colloids and Surfaces A: Physicochemical and Engineering Aspects · doi:10.1016/j.colsurfa.2004.04.007 · Cited by 663 · cited 1×
“A redox reaction has taken place during KOH activation, where the carbon is oxidized to CO or CO2, thus generating pores [59].”
BackgroundLiu, Z., Zhang, F.-S., & Wu, J. (2010) · Fuel · doi:10.1016/j.fuel.2009.08.042 · Cited by 545 · cited 2×
“4m(2)·g) [34], maize silage (12m(2)·g) [47], and pinewood (21m(2)·g) [48], probably due to the special structure of S.”
BackgroundCui, X., Bustin, R. M., & Dipple, G. (2004) · Fuel · doi:10.1016/j.fuel.2003.09.001 · Cited by 536 · cited 1×
“reported that the largest adsorption energy could be reached when the pore size of the adsorbent was 1–2 times larger than the kinetic diameter of the adsorbatemolecule [49].”
BackgroundTitirici, M. M., Thomas, A., Yu, S.-H., Müller, J.-O., & Antonietti, M. (2007) · Chemistry of Materials · doi:10.1021/cm0707408 · Cited by 535 · cited 1×
“Fe (NH4)2(SO4)2·6H2O was used as the catalyst because (i) the presence of iron ions could effectively speed up the hydrothermal carbonization process and significantly reduce the reaction time and the reaction temperature [37, 38], (ii) iron ion had a catalytic effect on the evolution of gases, contributing to produce…”
MethodLourenco, S. O., Barbarino, E., De-Paula, J. C., Pereira, L. O. D. S., & Marquez, U. M. L. (2002) · Phycological Research · doi:10.1111/j.1440-1835.2002.tb00156.x · Cited by 476
Controllable Synthesis of Conducting Polypyrrole Nanostructures
Zhang, X., Zhang, J., Song, W., & Liu, Z. (2006) · The Journal of Physical Chemistry B · doi:10.1021/jp054335k · Cited by 432 · cited 1×
“For the HC, the adsorption peak in the 3000–3500 cm range was associated with H-bonded O-H vibration [51], and the band at around 2930 cm was assigned to C-H stretching.”
BackgroundImportance of small micropores in CO 2 capture by phenolic resin-based activated carbon spheres
Wickramaratne, N. P., & Jaroniec, M. (2013) · J. Mater. Chem. A · doi:10.1039/c2ta00388k · Cited by 415
Assessment of the Role of Micropore Size and N-Doping in CO 2 Capture by Porous Carbons
Sevilla, M., Parra, J. B., & Fuertes, A. B. (2013) · ACS Applied Materials & Interfaces · doi:10.1021/am401423b · Cited by 410 · cited 2×
“e developed porosity can be achieved through adjusting the activation conditions [24].”
BackgroundHydrothermal carbonization of anaerobically digested maize silage
Mumme, J., Eckervogt, L., Pielert, J., Diakité, M., Rupp, F., & Kern, J. (2011) · Bioresource Technology · doi:10.1016/j.biortech.2011.06.099 · Cited by 399 · cited 3×
“4m(2)·g) [34], maize silage (12m(2)·g) [47], and pinewood (21m(2)·g) [48], probably due to the special structure of S.”
BackgroundCosmetic attributes of algae - A review
Ariede, M. B., Candido, T. M., Jacome, A. L. M., Velasco, M. V. R., de Carvalho, J. C. M., & Baby, A. R. (2017) · Algal Research · doi:10.1016/j.algal.2017.05.019 · Cited by 366
Shafeeyan, M. S., Daud, W. M. A. W., Houshmand, A., & Arami-Niya, A. (2011) · Applied Surface Science · doi:10.1016/j.apsusc.2010.11.127 · Cited by 328 · cited 1×
“2) [63] A material composed by zeolite and activated carbon 298 116 (2.”
BackgroundGao, P., Zhou, Y., Meng, F., Zhang, Y., Liu, Z., Zhang, W., & Xue, G. (2016) · Energy · doi:10.1016/j.energy.2015.12.123 · Cited by 314 · cited 1×
“Similar phenomenon was also found in other studies [44].”
ResultAn overview of marine macroalgae as bioresource
Sudhakar, K., Mamat, R., Samykano, M., Azmi, W. H., Ishak, W. F. W., & Yusaf, T. (2018) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2018.03.100 · Cited by 298
Critical role of small micropores in high CO2 uptake
Zhang, Z., Zhou, J., Xing, W., Xue, Q., Yan, Z., Zhuo, S., & Qiao, S. Z. (2013) · Physical Chemistry Chemical Physics · doi:10.1039/c2cp44436d · Cited by 263 · cited 1×
“54 nm) under different adsorption conditions [23].”
Cui, X., Antonietti, M., & Yu, S. (2006) · Small · doi:10.1002/smll.200600047 · Cited by 255 · cited 2×
“Fe (NH4)2(SO4)2·6H2O was used as the catalyst because (i) the presence of iron ions could effectively speed up the hydrothermal carbonization process and significantly reduce the reaction time and the reaction temperature [37, 38], (ii) iron ion had a catalytic effect on the evolution of gases, contributing to produce…”
BackgroundMethodBioactive compounds from marine macroalgae and their hypoglycemic benefits
Zhao, C., Yang, C., Liu, B., Lin, L., Sarker, S. D., Nahar, L., Yu, H., Cao, H., & Xiao, J. (2018) · Trends in Food Science & Technology · doi:10.1016/j.tifs.2017.12.001 · Cited by 235
A review of extractions of seaweed hydrocolloids: Properties and applications
Abdul Khalil, H. P. S., Lai, T. K., Tye, Y. Y., Rizal, S., Chong, E. W. N., Yap, S. W., Hamzah, A. A., Nurul Fazita, M. R., & Paridah, M. T. (2018) · Express Polymer Letters · doi:10.3144/expresspolymlett.2018.27 · Cited by 229
Zhao, Y., Liu, X., Yao, K. X., Zhao, L., & Han, Y. (2012) · Chemistry of Materials · doi:10.1021/cm303072n · Cited by 221 · cited 1×
“*e interactions are associated with the formation of the Lewis basic sites and the hydrogen-bonding between carbon surface and CO2 molecules [26, 27].”
BackgroundThermogravimetric characteristics and pyrolysis kinetics of Alga Sagarssum sp. biomass
Kim, S.-S., Ly, H. V., Kim, J., Choi, J. H., & Woo, H. C. (2013) · Bioresource Technology · doi:10.1016/j.biortech.2013.03.192 · Cited by 201 · cited 1×
“In the second stage, a significant weight loss of approximately 38% was achieved between 200 and 400°C, corresponding to the decomposition of biopolymer fractions [41].”
BackgroundHydrothermal synthesis of microalgae-derived microporous carbons for electrochemical capacitors
Sevilla, M., Gu, W., Falco, C., Titirici, M. M., Fuertes, A. B., & Yushin, G. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2014.05.046 · Cited by 190 · cited 1×
“However, traditional dry pyrolysis cannot meet the requirement for high carbon yield [14, 15].”
BackgroundWang, L., Rao, L., Xia, B., Wang, L., Yue, L., Liang, Y., DaCosta, H., & Hu, X. (2018) · Carbon · doi:10.1016/j.carbon.2018.01.003 · Cited by 172 · cited 1×
“In addition, it is generally accepted that the introduction of nitrogen-containing functional groups into carbon materials can generate more active sites, strengthening the interactions between carbon surface and CO2 molecules for improving the CO2 adsorption capacity [25].”
BackgroundXu, Q., Qian, Q., Quek, A., Ai, N., Zeng, G., & Wang, J. (2013) · ACS Sustainable Chemistry & Engineering · doi:10.1021/sc400118f · Cited by 167 · cited 3×
“horneri by hydrothermal treatment in our previous work [35, 36].”
BackgroundMethodSelf-citationDevelopment of microporous carbons for CO2 capture by KOH activation of African palm shells
Ello, A. S., de Souza, L. K. C., Trokourey, A., & Jaroniec, M. (2013) · Journal of CO2 Utilization · doi:10.1016/j.jcou.2013.07.003 · Cited by 165 · cited 1×
“50 nm), indicating that the KOH activation contributes the most to the formation of micropore structures [60].”
BackgroundChandrasekar, G., Son, W.-J., & Ahn, W.-S. (2009) · Journal of Porous Materials · doi:10.1007/s10934-008-9231-x · Cited by 161 · cited 1×
“7) [62] Amino-modied peat-based activated carbon 298 96 (2.”
CO2 Capture in Different Carbon Materials
Jiménez, V., Ramírez-Lucas, A., Díaz, J. A., Sánchez, P., & Romero, A. (2012) · Environmental Science & Technology · doi:10.1021/es2046553 · Cited by 158 · cited 1×
“Recently, activated carbons especially microporous carbon prepared by KOH activation have emerged as the most promising adsorbent for CO2 capture due to their low cost of preparation, high specific surface area, and excellent chemical stability [13, 19].”
BackgroundCollins, K., Fitzgerald, G., Stanton, C., & Ross, R. (2016) · Marine Drugs · doi:10.3390/md14030060 · Cited by 155
Hierarchical porous polyacrylonitrile-based activated carbon fibers for CO2 capture
Shen, W., Zhang, S., He, Y., Li, J., & Fan, W. (2011) · Journal of Materials Chemistry · doi:10.1039/c1jm12585k · Cited by 154 · cited 1×
“is is due to the fact that the CO2 uptake of activated carbon was not only contributed by functional groups on the surface, but also determined by the porous structure and specic surface area [61].”
BackgroundPyrolytic characteristics and kinetic studies of three kinds of red algae
Li, D., Chen, L., Zhang, X., Ye, N., & Xing, F. (2011) · Biomass and Bioenergy · doi:10.1016/j.biombioe.2011.01.011 · Cited by 153
Graphitic Biocarbon from Metal-Catalyzed Hydrothermal Carbonization of Lignin
Demir, M., Kahveci, Z., Aksoy, B., Palapati, N. K. R., Subramanian, A., Cullinan, H. T., El-Kaderi, H. M., Harris, C. T., & Gupta, R. B. (2015) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.5b02614 · Cited by 149 · cited 1×
“However, almost no sharp (002) diffraction peak has been observed in the hydrochars from other biomass [54].”
BackgroundZhou, H., Zhang, J., Amiinu, I. S., Zhang, C., Liu, X., Tu, W., Pan, M., & Mu, S. (2016) · Physical Chemistry Chemical Physics · doi:10.1039/c6cp00174b · Cited by 128 · cited 1×
“Besides, there is a significant weight loss in the final stage above 600°C, suggesting that the carbon is severely etched by KOH to form the well-developed porous structure [46].”
BackgroundSustainable and hierarchical porous Enteromorpha prolifera based carbon for CO2 capture
Zhang, Z., Wang, K., Atkinson, J. D., Yan, X., Li, X., Rood, M. J., & Yan, Z. (2012) · Journal of Hazardous Materials · doi:10.1016/j.jhazmat.2012.05.094 · Cited by 120 · cited 4×
“*e bands at 500–800 cm region corresponded to out-of-plane N-H deformation vibration [34].”
BackgroundInfluentialBiancarosa, I., Liland, N. S., Biemans, D., Araujo, P., Bruckner, C. G., Waagbø, R., Torstensen, B. E., Lock, E., & Amlund, H. (2018) · Journal of the Science of Food and Agriculture · doi:10.1002/jsfa.8702 · Cited by 119
Lin, Q. H., Cheng, H., & Chen, G. Y. (2012) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2011.10.006 · Cited by 117 · cited 1×
“In general, activated carbons with welldeveloped porosity, especially narrow microporosity, are prepared by chemical activation using activating agents such as KOH, ZnCl2, and H3PO4 [18].”
BackgroundPourhosseini, S. E. M., Norouzi, O., & Naderi, H. R. (2017) · Biomass and Bioenergy · doi:10.1016/j.biombioe.2017.10.025 · Cited by 112
Xing, Q., Guo, R., Wu, L., An, D., Cong, M., Qin, S., & Li, X. (2017) · IEEE Geoscience and Remote Sensing Letters · doi:10.1109/lgrs.2017.2737079 · Cited by 111 · cited 1×
“horneri golden tides brought its detrimental side to tourism-based economics, coastal ecosystems, ocean transportation, and water quality [5, 6].”
BackgroundDistribution of drifting seaweeds in eastern East China Sea
Komatsu, T., Tatsukawa, K., Filippi, J. B., Sagawa, T., Matsunaga, D., Mikami, A., Ishida, K., Ajisaka, T., Tanaka, K., Aoki, M., et al. (2007) · Journal of Marine Systems · doi:10.1016/j.jmarsys.2006.05.018 · Cited by 98 · cited 1×
“horneri can compete with microplankton, protozoan, and even bacteria for nutrients, inhibiting the harmful algae blooms [4].”
BackgroundBiobased Functional Carbon Materials: Production, Characterization, and Applications—A Review
Correa, C. R., & Kruse, A. (2018) · Materials · doi:10.3390/ma11091568 · Cited by 93 · cited 1×
“Hemicellulose is easy to liquefy and degrades into smaller molecules under mild hydrothermal temperature (180°C) [56], while the cellulose and lignin significantly decomposes under hydrothermal conditions above approximately 200°C [57, 58].”
BackgroundLuo, L., Chen, T., Li, Z., Zhang, Z., Zhao, W., & Fan, M. (2018) · Journal of CO2 Utilization · doi:10.1016/j.jcou.2018.03.014 · Cited by 92 · cited 1×
“*e second stage in the wide temperature range of 200–600°C could be attributed to the decomposition of the biopolymer and KOH [45].”
BackgroundNew hybrid composite honeycomb monolith with 13X zeolite and activated carbon for CO2 capture
Regufe, M. J., Ferreira, A. F. P., LOUREIRO, J. M., Shi, Y., Rodrigues, A. E., & Ribeiro, A. M. (2018) · Adsorption · doi:10.1007/s10450-018-9938-1 · Cited by 82 · cited 1×
“63) [64] A metal-rich wood-based activated carbon 298 83 (1.”
Zhao, W., Yuan, P., She, X., Xia, Y., Komarneni, S., Xi, K., Che, Y., Yao, X., & Yang, D. (2015) · Journal of Materials Chemistry A · doi:10.1039/c5ta03199k · Cited by 81 · cited 1×
“After carbonization of the M-alginates and subsequent acid washing, the metal cations can be removed to produce carbon materials with special porous structure [12].”
MethodShen, F., Wang, Y., Li, L., Zhang, K., Smith, R. L., & Qi, X. (2018) · Chemical Engineering Communications · doi:10.1080/00986445.2017.1367671 · Cited by 65 · cited 1×
“However, traditional dry pyrolysis cannot meet the requirement for high carbon yield [14, 15].”
BackgroundBotomé, M. L., Poletto, P., Junges, J., Perondi, D., Dettmer, A., & Godinho, M. (2017) · Chemical Engineering Journal · doi:10.1016/j.cej.2017.04.004 · Cited by 64
Abundance of drifting seaweeds in eastern East China Sea
Komatsu, T., 松永, 大., Mikami, A., Sagawa, T., Boisnier, E., Tatsukawa, K., Aoki, M., Ajisaka, T., Uwai, S., Tanaka, K., et al. (2008) · Journal of Applied Phycology · doi:10.1007/s10811-007-9302-4 · Cited by 64
Syaftika, N., & Matsumura, Y. (2018) · Bioresource Technology · doi:10.1016/j.biortech.2018.01.085 · Cited by 63 · cited 1×
“horneri is mainly cross linked with hemicellulose and lignin [55].”
BackgroundTiwari, D., Bhunia, H., & Bajpai, P. K. (2018) · Journal of Environmental Management · doi:10.1016/j.jenvman.2018.04.088 · Cited by 58
Preparation of activated carbons from poplar wood by chemical activation with KOH
Li, Z., Gao, X., Wu, L., Wang, K., & Kobayashi, N. (2016) · Journal of Porous Materials · doi:10.1007/s10934-016-0252-6 · Cited by 56 · cited 1×
“*e first stage occurred at the temperature range of 30– 200°C, with one peak centered at 68°C, due to vaporization of adsorbed water on the surface [40].”
BackgroundHighly porous nitrogen-doped seaweed carbon for high-performance lithium–sulfur batteries
Hencz, L., Gu, X., Zhou, X., Martens, W., & Zhang, S. (2017) · Journal of Materials Science · doi:10.1007/s10853-017-1288-y · Cited by 55 · cited 1×
“Recently, activated carbons especially microporous carbon prepared by KOH activation have emerged as the most promising adsorbent for CO2 capture due to their low cost of preparation, high specific surface area, and excellent chemical stability [13, 19].”
BackgroundThermal characterization and pyrolysis of digestate for phenol production
Wei, Y., Hong, J., & Ji, W. (2018) · Fuel · doi:10.1016/j.fuel.2018.05.134 · Cited by 46 · cited 1×
“*e weight loss of the final stage at a temperature range of 400–800°C might be attributed to the degradation of lignin and remaining proteins [43].”
BackgroundWu, X., Tian, Z., Hu, L., Huang, S., & Cai, J. (2017) · RSC Advances · doi:10.1039/c7ra05355j · Cited by 41
Self-citationPintor, M.-J., Jean-Marius, C., Jeanne-Rose, V., Taberna, P.-L., Simon, P., Gamby, J., Gadiou, R., & Gaspard, S. (2013) · Comptes Rendus. Chimie · doi:10.1016/j.crci.2012.12.016 · Cited by 36
Roberts, A. D., Lee, J.-S. M., Wong, S. Y., Li, X., & Zhang, H. (2017) · Journal of Materials Chemistry A · doi:10.1039/c6ta09078h · Cited by 36
Preparation and characterization of waste ion-exchange resin-based activated carbon for CO2 capture
Wei, M., Yu, Q., Mu, T., Hou, L., Zuo, Z., & Peng, J. (2016) · Adsorption · doi:10.1007/s10450-016-9787-8 · Cited by 30 · cited 1×
“8) [66] Sargassum horneri-based porous carbon (AHC) 303 101.”
Escobar, B., Pérez-Salcedo, K. Y., Alonso-Lemus, I. L., Pacheco, D., & Barbosa, R. (2017) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2017.06.240 · Cited by 30
Nitrogen self-doped carbon nanoparticles derived from spiral seaweeds for oxygen reduction reaction
Liu, F., Liu, L., Li, X., Zeng, J., Du, L., & Liao, S. (2016) · RSC Advances · doi:10.1039/c5ra27499k · Cited by 25
Hydrothermal Treatment of Tannin: A Route to Porous Metal Oxides and Metal/Carbon Hybrid Materials
Braghiroli, F., Fierro, V., Szczurek, A., Gadonneix, P., Ghanbaja, J., Parmentier, J., Medjahdi, G., & Celzard, A. (2017) · Inorganics · doi:10.3390/inorganics5010007 · Cited by 25 · cited 2×
“[38] pointed out that the iron ion had a catalytic effect on the production of gas, contributing to the production of carbon materials with higher porosity and surface area.”
BackgroundMethodActivated carbon derived from hydrothermal treatment of sucrose and its air filtration application
Hao, S.-W., Hsu, C.-H., Liu, Y., & Chang, B. K. (2016) · RSC Advances · doi:10.1039/c6ra23958g · Cited by 24 · cited 1×
“*e peak at 1620 cm corresponded to the C�C stretching vibration [52].”
BackgroundApplication of seaweeds for the removal of cationic dye from aqueous solution
Jegan, J., Vijayaraghavan, J., Pushpa, T. B., et al. (2016) · Desalination and Water Treatment · doi:10.1080/19443994.2016.1151835 · Cited by 23
Gan, H., Cai, J., Zhang, C., Dong, Z., Jin, H., & Zhang, K. (2017) · Desalination and Water Treatment · doi:10.5004/dwt.2017.20444 · Cited by 3
Titirici, M., & Antonietti, M. (2010) · ChemInform · doi:10.1002/chin.201016219 · Cited by 1
Research works printed but not linked: 2
- 2014, Acta Scientiae Circumstantiae, 34, 392
- 1950, Fuel, 29, 269
Cited by
Zubbri, N. A., Mohamed, A. R., Lahijani, P., & Mohammadi, M. (2021) · Journal of Environmental Chemical Engineering · doi:10.1016/j.jece.2021.105074 · Cited by 106
Kamran, U., & Park, S. (2021) · Journal of Colloid and Interface Science · doi:10.1016/j.jcis.2021.03.069 · Cited by 57
Mesfer, M. K. A. (2020) · Environmental Science and Pollution Research · doi:10.1007/s11356-020-07934-x · Cited by 54
“7 mg/g at 30 °C was reported using microporous activated carbon synthesized from Sargassum hornei biomass (Zeng et al. 2018).”
MethodInfluentialFacile synthesis of macroalgae-derived graphene adsorbents for efficient CO2 capture
Ai, N., Lou, S., Lou, F., Xu, C., Wang, Q., & Zeng, G. (2021) · Process Safety and Environmental Protection · doi:10.1016/j.psep.2021.02.014 · Cited by 46
Self-citationRahimi, M., Thanh, H. V., Ebrahimzade, I., Abbaspour‐Fard, M. H., & Rohani, A. (2023) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2023.136606 · Cited by 39
Metadata
- Authors
- Zeng, G., Lou, S., Ying, H., Wu, X., Dou, X., Ai, N., & Wang, J.
- Affiliations
- Memorial University of Newfoundland (CA)
- Zhejiang University of Technology (CN)
- Aston University (GB)
- Corresponding author
- Ai, Ning
- Venue
- Journal of Chemistry
- Publisher
- Wiley
- Published
- 2018-12-13
- Volume
- 2018
- Pages
- 1-11
- ISSN
- 2090-9063 (ISSN-L)
- 2090-9071
- OpenAlex
- W2905236503
- Cited by
- 44
- References
- 66
- Citations by year
- 2026: 4 · 2025: 13 · 2024: 7 · 2023: 7 · 2022: 2 · 2021: 8 · 2020: 2 · 2019: 1
- FWCI
- 0.90
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Locations
- Journal of Chemistry (publishedVersion, cc-by)
- Aston Publications Explorer (Aston University) (acceptedVersion)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Funders
- National Natural Science Foundation of China (21628601, 51728902, LY16B060014, LGF18D060002, SKL-ChE-08A01)
- Natural Science Foundation of Zhejiang Province (21628601, 51728902, LY16B060014, LGF18D060002, SKL-ChE-08A01)
- State Key Laboratory of Chemical Engineering (21628601, 51728902, LY16B060014, LGF18D060002, SKL-ChE-08A01)
- Topics
- Physical Sciences › Chemical Engineering › Filtration and Separation › Carbon Dioxide Capture Technologies
- Physical Sciences › Environmental Science › Water Science and Technology › Adsorption and biosorption for pollutant removal
- Physical Sciences › Energy › Fuel Technology › Thermochemical Biomass Conversion Processes
- Keywords
- Sargassum horneri, activated carbon, microporous carbon, CO2 capture, hydrothermal carbonization, KOH activation, hydrochar, CO2 adsorption, adsorption kinetics, adsorbent regeneration, specific surface area
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-11, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-11 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.