The DOI matches its Crossref record; 114 of the 114 references it cites were found in a registry or an index.
A critical review of thermal management models and solutions of lithium-ion batteries for the development of pure electric vehicles
Open accessAbstract
Power train electrification is promoted as a potential alternative to reduce carbon intensity of transportation. Lithium-ion batteries are found to be suitable for hybrid electric vehicles (HEVs) and pure electric vehicles (EVs), and temperature control on lithium batteries is vital for long-term performance and durability. Unfortunately, battery thermal management (BTM) has not been paid close attention partly due to poor understanding of battery thermal behaviour. Cell performance change dramatically with temperature, but it improves with temperature if a suitable operating temperature window is sustained. This paper provides a review on two aspects that are battery thermal model development and thermal management strategies. Thermal effects of lithium-ion batteries in terms of thermal runaway and response under cold temperatures will be studied, and heat generation methods are discussed with aim of performing accurate battery thermal analysis. In addition, current BTM strategies utilised by automotive suppliers will be reviewed to identify the imposing challenges and critical gaps between research and practice. Optimising existing BTMs and exploring new technologies to mitigate battery thermal impacts are required, and efforts in prioritising BTM should be made to improve the temperature uniformity across the battery pack, prolong battery lifespan, and enhance the safety of large packs.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
A review on the key issues for lithium-ion battery management in electric vehicles
Lu, L., Han, X., Li, J., Hua, J., & Ouyang, M. (2013) · Journal of Power Sources · doi:10.1016/j.jpowsour.2012.10.060 · Cited by 4,837
Modeling of Galvanostatic Charge and Discharge of the Lithium/Polymer/Insertion Cell
Doyle, M., Fuller, T. F., & Newman, J. (1993) · Journal of The Electrochemical Society · doi:10.1149/1.2221597 · Cited by 4,328 · cited 1×
“It was first developed by Newman’s group [98, 99] based on a macro-homogeneous and isothermal model approach [100].”
Lowering the Temperature of Solid Oxide Fuel Cells
Wachsman, E. D., & Lee, K. T. (2011) · Science · doi:10.1126/science.1204090 · Cited by 2,554
A General Energy Balance for Battery Systems
Bernardi, D., Pawlikowski, E., & Newman, J. (1985) · Journal of The Electrochemical Society · doi:10.1149/1.2113792 · Cited by 2,548 · cited 1×
“[113] formulated the thermodynamic energy balance on a single cell, and a simplified form (Eq.”
A critical review of thermal issues in lithium-ion batteries
Bandhauer, T. M., Garimella, S., & Fuller, T. F. (2011) · Journal of The Electrochemical Society · doi:10.1149/1.3515880 · Cited by 2,192
Simulation and Optimization of the Dual Lithium Ion Insertion Cell
Fuller, T. F., Doyle, M., & Newman, J. (1994) · Journal of The Electrochemical Society · doi:10.1149/1.2054684 · Cited by 2,057
Linden, D. (2001) · CERN Document Server (European Organization for Nuclear Research) · Cited by 1,900
Comparison of Modeling Predictions with Experimental Data from Plastic Lithium Ion Cells
Doyle, M., Newman, J., Gozdz, A. S., Schmutz, C. N., & Tarascon, J. (1996) · Journal of The Electrochemical Society · doi:10.1149/1.1836921 · Cited by 1,569
A review of power battery thermal energy management
Rao, Z., & Wang, S. (2011) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2011.07.096 · Cited by 1,207
He, H., Xiong, R., & Fan, J. (2011) · Energies · doi:10.3390/en4040582 · Cited by 1,180
Safety mechanisms in lithium-ion batteries
Balakrishnan, P. G., Ramesh, R., & Prem Kumar, T. (2006) · Journal of Power Sources · doi:10.1016/j.jpowsour.2005.12.002 · Cited by 1,132
Battery thermal models for hybrid vehicle simulations
Pesaran, A. A. (2002) · Journal of Power Sources · doi:10.1016/s0378-7753(02)00200-8 · Cited by 1,116 · cited 2×
“Sato [115] <50 Lithium-ion Pesaran [137] 25-40 Lead-acid, NiMH, and Lithium-ion Panasonic [145] 0-45 for charge -10-60 for discharge Lithium-ion”
Waag, W., Käbitz, S., & Sauer, D. U. (2013) · Applied Energy · doi:10.1016/j.apenergy.2012.09.030 · Cited by 987 · cited 1×
“Battery thermal management (BTM) is therefore required to help the battery operate at a desirable working temperature range at all times preventing battery degradation [147, 148], thermal runaway [149-151], and dropped discharge capacity due to sub-zero climate [76].”
Electrochemical impedance study on the low temperature of Li-ion batteries
Zhang, S. S., Xu, K., & Jow, T. R. (2004) · Electrochimica Acta · doi:10.1016/j.electacta.2003.10.016 · Cited by 933
ADVISOR: a systems analysis tool for advanced vehicle modeling
Markel, T., Brooker, A., Hendricks, T., Johnson, V, Kelly, K., Kramer, B., O’Keefe, M., Sprik, S., & Wipke, K. (2002) · Journal of Power Sources · doi:10.1016/s0378-7753(02)00189-1 · Cited by 849
Hołyst, R., & Poniewierski, A. (2012) · Thermodynamics for Chemists, Physicists and Engineers · doi:10.1007/978-94-007-2999-5_11 · Cited by 812
Reciprocating air flow for Li-ion battery thermal management to improve temperature uniformity
Mahamud, R., & Park, C. (2011) · Journal of Power Sources · doi:10.1016/j.jpowsour.2011.02.076 · Cited by 787
Power and thermal characterization of a lithium-ion battery pack for hybrid-electric vehicles
Smith, K., & Wang, C.-Y. (2006) · Journal of Power Sources · doi:10.1016/j.jpowsour.2006.01.038 · Cited by 763
Thermal-Electrochemical Modeling of Battery Systems
Gu, W. B., & Wang, C. Y. (2000) · Journal of The Electrochemical Society · doi:10.1149/1.1393625 · Cited by 746
The low temperature performance of Li-ion batteries
Zhang, S. S., Xu, K., & Jow, T. R. (2003) · Journal of Power Sources · doi:10.1016/s0378-7753(02)00618-3 · Cited by 712 · cited 2×
“Poor lithium-ion battery performance under cold climates is therefore studied [84, 86, 87] which can be summarised from four factors: 1) low conductivity of the electrolyte and solid electrolyte interface on the electrode surface [88, 89]; 2) declined solid-state Li diffusivity [80, 84]; 3) high polarisation of the gr…”
Thermal analysis of lithium-ion batteries
Chen, S. C., Wan, C. C., & Wang, Y. Y. (2005) · Journal of Power Sources · doi:10.1016/j.jpowsour.2004.05.064 · Cited by 708
Lee, S., Kim, J., Lee, J., & Cho, B. H. (2008) · Journal of Power Sources · doi:10.1016/j.jpowsour.2008.08.103 · Cited by 698
Sabbah, R., Kizilel, R., Selman, J. R., & Al-Hallaj, S. (2008) · Journal of Power Sources · doi:10.1016/j.jpowsour.2008.03.082 · Cited by 680
A lumped-parameter electro-thermal model for cylindrical batteries
Lin, X., Perez, H. E., Mohan, S., Siegel, J. B., Stefanopoulou, A. G., Ding, Y., & Castanier, M. P. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2014.01.097 · Cited by 677 · cited 1×
“Figure 11: Coupled thermal-electrical model for an A123 LiPO4/graphite battery [111].”
A Novel Thermal Management System for Electric Vehicle Batteries Using Phase-Change Material
Hallaj, S. A., & Selman, J. R. (2000) · Journal of The Electrochemical Society · doi:10.1149/1.1393888 · Cited by 662
Battery performance models in ADVISOR
Johnson, V. H. (2002) · Journal of Power Sources · doi:10.1016/s0378-7753(02)00194-5 · Cited by 636
Paraffin/porous-graphite-matrix composite as a high and constant power thermal storage material
Py, X., Olives, R., & Mauran, S. (2001) · International Journal of Heat and Mass Transfer · doi:10.1016/s0017-9310(00)00309-4 · Cited by 618
A General Discussion of Li Ion Battery Safety
(2012) · Electrochemical Society Interface · doi:10.1149/2.f03122if · Cited by 592
Design optimization of electric vehicle battery cooling plates for thermal performance
Jarrett, A., & Kim, I. Y. (2011) · Journal of Power Sources · doi:10.1016/j.jpowsour.2011.06.090 · Cited by 560
Thermal Analysis of Lithium‐Ion Batteries
Chen, Y., & Evans, J. W. (1996) · Journal of The Electrochemical Society · doi:10.1149/1.1837095 · Cited by 545
Study on paraffin/expanded graphite composite phase change thermal energy storage material
Zhang, Z., & Fang, X. (2006) · Energy Conversion and Management · doi:10.1016/j.enconman.2005.03.004 · Cited by 518
An alternative cooling system to enhance the safety of Li-ion battery packs
Kizilel, R., Sabbah, R., Selman, J. R., & Al-Hallaj, S. (2009) · Journal of Power Sources · doi:10.1016/j.jpowsour.2009.06.074 · Cited by 513
Experimental investigation on thermal management of electric vehicle battery with heat pipe
Rao, Z., Wang, S., Wu, M., Lin, Z., & Li, F. (2013) · Energy Conversion and Management · doi:10.1016/j.enconman.2012.08.014 · Cited by 486
Heating strategies for Li-ion batteries operated from subzero temperatures
Ji, Y., & Wang, C. Y. (2013) · Electrochimica Acta · doi:10.1016/j.electacta.2013.03.147 · Cited by 485
Huria, T., Ceraolo, M., Gazzarri, J., & Jackey, R. (2012) · 2012 IEEE International Electric Vehicle Conference · doi:10.1109/ievc.2012.6183271 · Cited by 470
Thermal modeling and design considerations of lithium-ion batteries
Al Hallaj, S., Maleki, H., Hong, J. S., & Selman, J. R. (1999) · Journal of Power Sources · doi:10.1016/s0378-7753(99)00178-0 · Cited by 454
Analysis of Electrochemical and Thermal Behavior of Li-Ion Cells
Srinivasan, V., & Wang, C. Y. (2003) · Journal of The Electrochemical Society · doi:10.1149/1.1526512 · Cited by 435
Thermal behavior analysis of lithium-ion batteries for electric and hybrid vehicles
Sato, N. (2001) · Journal of Power Sources · doi:10.1016/s0378-7753(01)00478-5 · Cited by 428
Numerical investigation of a PCM-based heat sink with internal fins
Shatikian, V., Ziskind, G., & Letan, R. (2005) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2004.10.042 · Cited by 420
Li, W. Q., Qu, Z. G., He, Y. L., & Tao, Y. B. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2014.01.006 · Cited by 416
Khateeb, S. A., Amiruddin, S., Farid, M., Selman, J. R., & Al-Hallaj, S. (2005) · Journal of Power Sources · doi:10.1016/j.jpowsour.2004.09.033 · Cited by 410
Khateeb, S. A., Farid, M. M., Selman, J. R., & Al-Hallaj, S. (2004) · Journal of Power Sources · doi:10.1016/j.jpowsour.2003.09.070 · Cited by 405
The Limits of Low-Temperature Performance of Li-Ion Cells
Huang, C. K., Sakamoto, J. S., Wolfenstine, J., & Surampudi, S. (2000) · Journal of The Electrochemical Society · doi:10.1149/1.1393622 · Cited by 401
Prada, E., Di Domenico, D., Creff, Y., Bernard, J., Sauvant-Moynot, V., & Huet, F. (2012) · Journal of The Electrochemical Society · doi:10.1149/2.064209jes · Cited by 398
Li, W. Q., Qu, Z. G., He, Y. L., & Tao, W. Q. (2012) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2011.11.001 · Cited by 396
Thermal conductivity enhancement of energy storage media using carbon fibers
Fukai, J., Kanou, M., Kodama, Y., & Miyatake, O. (2000) · Energy Conversion and Management · doi:10.1016/s0196-8904(99)00166-1 · Cited by 395
Ultra-thin minichannel LCP for EV battery thermal management
Jin, L. W., Lee, P. S., Kong, X. X., Fan, Y., & Chou, S. K. (2014) · Applied Energy · doi:10.1016/j.apenergy.2013.07.013 · Cited by 393
Amjad, S., Neelakrishnan, S., & Rudramoorthy, R. (2010) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2009.11.001 · Cited by 387
Thermal conductivity enhancement in a latent heat storage system
Mettawee, E.-B. S., & Assassa, G. M. R. (2007) · Solar Energy · doi:10.1016/j.solener.2006.11.009 · Cited by 378
Cai, L., & White, R. E. (2011) · Journal of Power Sources · doi:10.1016/j.jpowsour.2011.03.017 · Cited by 377
Thermal behavior of small lithium-ion battery during rapid charge and discharge cycles
Onda, K., Ohshima, T., Nakayama, M., Fukuda, K., & Araki, T. (2006) · Journal of Power Sources · doi:10.1016/j.jpowsour.2005.08.049 · Cited by 375
Heat dissipation design for lithium-ion batteries
Wu, M.-S., Liu, K. H., Wang, Y.-Y., & Wan, C.-C. (2002) · Journal of Power Sources · doi:10.1016/s0378-7753(02)00048-4 · Cited by 373
Mathematical modeling of lithium-ion and nickel battery systems
Gomadam, P. M., Weidner, J. W., Dougal, R. A., & White, R. E. (2002) · Journal of Power Sources · doi:10.1016/s0378-7753(02)00190-8 · Cited by 344
Electrolytes for Low‐Temperature Lithium Batteries Based on Ternary Mixtures of Aliphatic Carbonates
Smart, M. C., Ratnakumar, B. V., & Surampudi, S. (1999) · Journal of The Electrochemical Society · doi:10.1149/1.1391633 · Cited by 339 · cited 2×
“Poor lithium-ion battery performance under cold climates is therefore studied [84, 86, 87] which can be summarised from four factors: 1) low conductivity of the electrolyte and solid electrolyte interface on the electrode surface [88, 89]; 2) declined solid-state Li diffusivity [80, 84]; 3) high polarisation of the gr…”
Heat transfer in phase change materials for thermal management of electric vehicle battery modules
Duan, X., & Naterer, G. F. (2010) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2010.07.044 · Cited by 335
Experimental investigation on EV battery cooling and heating by heat pipes
Wang, Q., Jiang, B., Xue, Q. F., Sun, H. L., Li, B., Zou, H. M., & Yan, Y. Y. (2015) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2014.09.083 · Cited by 329
Self-citationElectric vehicles: The role and importance of standards in an emerging market
Brown, S., Pyke, D., & Steenhof, P. (2010) · Energy Policy · doi:10.1016/j.enpol.2010.02.059 · Cited by 322
Rao, Z., Wang, S., & Zhang, G. (2011) · Energy Conversion and Management · doi:10.1016/j.enconman.2011.07.009 · Cited by 322
Fang, W., Kwon, O. J., & Wang, C.-Y. (2010) · International Journal of Energy Research · doi:10.1002/er.1652 · Cited by 314
Andersen, P. H., Mathews, J. A., & Rask, M. (2009) · Energy Policy · doi:10.1016/j.enpol.2009.03.032 · Cited by 311
Modeling for the scale-up of a lithium-ion polymer battery
Kim, U. S., Shin, C. B., & Kim, C.-S. (2009) · Journal of Power Sources · doi:10.1016/j.jpowsour.2008.10.019 · Cited by 308
Effect of electrode configuration on the thermal behavior of a lithium-polymer battery
Kim, U. S., Shin, C. B., & Kim, C.-S. (2008) · Journal of Power Sources · doi:10.1016/j.jpowsour.2007.09.054 · Cited by 292
Experimental study on the phase change behavior of phase change material confined in pores
Zhang, D., Tian, S., & Xiao, D. (2007) · Solar Energy · doi:10.1016/j.solener.2006.08.010 · Cited by 281
Capacity fade of Sony 18650 cells cycled at elevated temperatures
Ramadass, P., Haran, B., White, R., & Popov, B. N. (2002) · Journal of Power Sources · doi:10.1016/s0378-7753(02)00473-1 · Cited by 280
Experimental investigation on the feasibility of heat pipe cooling for HEV/EV lithium-ion battery
Tran, T.-H., Harmand, S., Desmet, B., & Filangi, S. (2014) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2013.11.048 · Cited by 279
Energy saving and energy efficiency concepts for policy making
Oikonomou, V., Becchis, F., Steg, L., & Russolillo, D. (2009) · Energy Policy · doi:10.1016/j.enpol.2009.06.035 · Cited by 271
An overview of energy sources for electric vehicles
Chau, K. T., Wong, Y. S., & Chan, C. C. (1999) · Energy Conversion and Management · doi:10.1016/s0196-8904(99)00021-7 · Cited by 255
Electrical characteristics of 18650 Li-ion cells at low temperatures
Nagasubramanian, G. (2001) · Journal of Applied Electrochemistry · doi:10.1023/a:1004113825283 · Cited by 254
Electrochemical-Thermal Model of Lithium Polymer Batteries
Song, L., & Evans, J. W. (2000) · Journal of The Electrochemical Society · doi:10.1149/1.1393490 · Cited by 252
Low-Temperature Behavior of Li-Ion Cells
Lin, H.-P., Chua, D., Salomon, M., Shiao, H.-C., Hendrickson, M., Plichta, E., & Slane, S. (2001) · Electrochemical and Solid-State Letters · doi:10.1149/1.1368736 · Cited by 248
Costs of lithium-ion batteries for vehicles
Gaines, L., & Cuenca, R. (2000) · doi:10.2172/761281 · Cited by 247
Mathematical modeling of secondary lithium batteries
Botte, G. G., Subramanian, V. R., & White, R. E. (2000) · Electrochimica Acta · doi:10.1016/s0013-4686(00)00340-6 · Cited by 235
Electrochemical‐Calorimetric Studies of Lithium‐Ion Cells
Hong, J., Maleki, H., Al Hallaj, S., Redey, L., & Selman, J. R. (1998) · Journal of The Electrochemical Society · doi:10.1149/1.1838509 · Cited by 234
Modeling thermal management of lithium-ion PNGV batteries
Nelson, P., Dees, D., Amine, K., & Henriksen, G. (2002) · Journal of Power Sources · doi:10.1016/s0378-7753(02)00197-0 · Cited by 234
Jhu, C.-Y., Wang, Y.-W., Wen, C.-Y., & Shu, C. (2012) · Applied Energy · doi:10.1016/j.apenergy.2012.05.064 · Cited by 230
Studies on Charging Lithium-Ion Cells at Low Temperatures
Fan, J., & Tan, S. (2006) · Journal of The Electrochemical Society · doi:10.1149/1.2190029 · Cited by 211 · cited 1×
“In addition, capacity fade due to lithium plating upon charging in cold climate has been studied [76, 83].”
A low-temperature electrolyte for lithium and lithium-ion batteries
Plichta, E. J., & Behl, W. K. (2000) · Journal of Power Sources · doi:10.1016/s0378-7753(00)00367-0 · Cited by 210
Alrashdan, A., Mayyas, A. T., & Al-Hallaj, S. (2010) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2009.07.011 · Cited by 209
Thermal Modeling of the Lithium/Polymer Battery: II . Temperature Profiles in a Cell Stack
Pals, C. R., & Newman, J. (1995) · Journal of The Electrochemical Society · doi:10.1149/1.2049975 · Cited by 206
Study of LiBF[sub 4] as an Electrolyte Salt for a Li-Ion Battery
Zhang, S. S., Xu, K., & Jow, T. R. (2002) · Journal of The Electrochemical Society · doi:10.1149/1.1466857 · Cited by 198
Heat Transfer Phenomena in Lithium/Polymer‐Electrolyte Batteries for Electric Vehicle Application
Chen, Y., & Evans, J. W. (1993) · Journal of The Electrochemical Society · doi:10.1149/1.2220724 · Cited by 194
Thermal Analysis of Spirally Wound Lithium Batteries
Chen, S.-C., Wang, Y.-Y., & Wan, C.-C. (2006) · Journal of The Electrochemical Society · doi:10.1149/1.2168051 · Cited by 191
Recent developments of lightweight, high performance heat pipes
Yang, X., Yan, Y., & Mullen, D. (2011) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2011.09.006 · Cited by 186
Self-citationThermal energy storage performance of paraffin in a novel tube-in-shell system
Akgün, M., Aydın, O., & Kaygusuz, K. (2008) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2007.05.013 · Cited by 184
HEV battery heating using AC currents
Stuart, T. A., & Hande, A. (2004) · Journal of Power Sources · doi:10.1016/j.jpowsour.2003.10.014 · Cited by 182
Chen, Y., & Evans, J. W. (1994) · Journal of The Electrochemical Society · doi:10.1149/1.2059263 · Cited by 177
Charge and discharge characteristics of a commercial LiCoO2-based 18650 Li-ion battery
Zhang, S. S., Xu, K., & Jow, T. R. (2006) · Journal of Power Sources · doi:10.1016/j.jpowsour.2006.03.037 · Cited by 175
A cost comparison of fuel-cell and battery electric vehicles
Eaves, S., & Eaves, J. (2004) · Journal of Power Sources · doi:10.1016/j.jpowsour.2003.12.016 · Cited by 158
Experimental investigation of a pulsating heat pipe for hybrid vehicle applications
Burban, G., Ayel, V., Alexandre, A., Lagonotte, P., Bertin, Y., & Romestant, C. (2012) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2012.05.037 · Cited by 153
An Approach for Designing Thermal Management Systems for Electric and Hybrid Vehicle Battery Packs
Pesaran, A. A., Keyser, M. A., & Burch, S. D. (1999) · University of North Texas Digital Library (University of North Texas) · Cited by 153
Characterization of commercial Li-ion batteries using electrochemical–calorimetric measurements
Al‐Hallaj, S., Prakash, J., & Selman, J. R. (2000) · Journal of Power Sources · doi:10.1016/s0378-7753(99)00472-3 · Cited by 145
Batteries for Plug-in Hybrid Electric Vehicles (PHEVs): Goals and the State of Technology circa 2008Preprint
Axsen, J., Burke, A., & Kurani, K. S. (2008) · RePEc: Research Papers in Economics · Cited by 138
Thermal Evaluation of Toyota Prius Battery Pack
Zolot, M., Pesaran, A. A., & Mihalic, M. (2002) · SAE technical papers on CD-ROM/SAE technical paper series · doi:10.4271/2002-01-1962 · Cited by 123
Cooling and Preheating of Batteries in Hybrid Electric Vehicles
Pesaran, A. A., Vlahinos, A. S., & Stuart, T. A. (2003) · Cited by 117
Preparation and thermal properties of paraffin/porous silica ceramic composite
Xiangfa, Z., Xiao, H., Feng, J., et al. (2009) · Composites Science and Technology · doi:10.1016/j.compscitech.2009.02.030 · Cited by 113
Research and development of electric vehicles for clean transportation
Wada, M. (2009) · Journal of Environmental Sciences · doi:10.1016/s1001-0742(08)62335-9 · Cited by 111
Batteries for Vehicular Applications
Srinivasan, V., Hafemeister, D., Levi, B., Levine, M., & Schwartz, P. (2008) · AIP conference proceedings · doi:10.1063/1.2993726 · Cited by 94
Low-Temperature Characterization of Lithium-Ion Carbon Anodes via Microperturbation Measurement
Wang, C.-S., Appleby, A., & Little, F. (2002) · Journal of The Electrochemical Society · doi:10.1149/1.1474427 · Cited by 90
Market penetration analysis of fuel cell vehicles in Japan by using the energy system model MARKAL
Endo, E. (2007) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2006.10.015 · Cited by 87
Thermal Properties of Paraffin Wax-based Composites Containing Graphite
Rao, Z., & Zhang, G. Q. (2010) · Energy Sources Part A Recovery Utilization and Environmental Effects · doi:10.1080/15567030903117679 · Cited by 84
Battery Hazards and Accident Prevention
Levy, S. C., & Bro, P. (1994) · doi:10.1007/978-1-4899-1459-0 · Cited by 78
Temperature Rise in Prismatic Polymer Lithium-Ion Batteries: An Analytic Approach
Taheri, P., & Bahrami, M. (2012) · SAE International journal of passenger cars. Electronic and electrical systems · doi:10.4271/2012-01-0334 · Cited by 77
Tools for Designing Thermal Management of Batteries in Electric Drive Vehicles (Presentation)
Pesaran, A. A., USDOE Office of Energy Efficiency and Renewable Energy Vehicle Technologies Program, Keyser, M., Kim, G., Santhanagopalan, S., & Smith, K. (2013) · OSTI OAI (U.S. Department of Energy Office of Scientific and Technical Information) · doi:10.2172/1064502 · Cited by 76
Energy Efficient Battery Heating in Cold Climates
Vlahinos, A. S., & Pesaran, A. A. (2002) · SAE technical papers on CD-ROM/SAE technical paper series · doi:10.4271/2002-01-1975 · Cited by 72
Design optimization of a loop heat pipe to cool a lithium ion battery onboard a military aircraft
Park, Y., Jun, S., Kim, S.-H., & Lee, D.-H. (2010) · Journal of Mechanical Science and Technology · doi:10.1007/s12206-009-1214-6 · Cited by 68
Battery thermal management system
Cosley, M. R., & Garcia, M. P. (2005) · International Workshop on Computational Electronics · doi:10.1109/intlec.2004.1401442 · Cited by 31
Heat Transfer in Lead‐Acid Batteries Designed for Electric‐Vehicle Propulsion Application
Choi, K.-H., & Yao, N. P. (1979) · Journal of The Electrochemical Society · doi:10.1149/1.2129270 · Cited by 25
(NNSA), U. N. N. S. A., Fuller, T. F., Sandia National Laboratories (SNL-NM), A., et al. (2012) · doi:10.2172/1038186 · Cited by 19
Battery hazards and accident prevention
Hall, A. H. (1995) · The American Journal of Emergency Medicine · doi:10.1016/0735-6757(95)90177-9 · Cited by 18
Heat pipes for thermal control of ISS solar battery drive
Barantsevich, V., & Shabalkin, V. (2003) · Applied Thermal Engineering · doi:10.1016/s1359-4311(03)00041-3 · Cited by 14
A novel thermal management system for EV batteries using phase-change material
Pengcha, J. (2014) · Huagong jinzhan · Cited by 13
Low Temperature Performance Analysis of Li-ion Batteries for Electric Vehicles
Ze, L. (2012) · Bus & Coach Technology and Research · Cited by 4
Chevy Volt fire prompts federal probe of lithium-ion batteries
(2011) · Physics Today · doi:10.1063/pt.5.025699 · Cited by 4
Cited by
A review of lithium-ion battery safety concerns: The issues, strategies, and testing standards
Chen, Y., Kang, Y., Zhao, Y., Wang, L., Liu, J., Li, Y., Liang, Z., He, X., Li, X., Tavajohi, N., et al. (2021) · Journal of Energy Chemistry · doi:10.1016/j.jechem.2020.10.017 · Cited by 2,178
Self-citationHannan, M. A., Lipu, M. S. H., Hussain, A., & Mohamed, A. (2017) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2017.05.001 · Cited by 2,005
Liu, H., Wei, Z., He, W., & Zhao, J. (2017) · Energy Conversion and Management · doi:10.1016/j.enconman.2017.08.016 · Cited by 1,332
Review on battery thermal management system for electric vehicles
Kim, J., Oh, J., & Lee, H. (2019) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2018.12.020 · Cited by 1,292
A critical review of battery thermal performance and liquid based battery thermal management
Wu, W., Wang, S., Wu, W., Chen, K., Hong, S., & Lai, Y. (2019) · Energy Conversion and Management · doi:10.1016/j.enconman.2018.12.051 · Cited by 1,214
Metadata
- Authors
- Wang, Q., Jiang, B., Li, B., & Yan, Y.
- Venue
- Renewable and Sustainable Energy Reviews
- Publisher
- Elsevier BV
- Published
- 2016-10
- Volume
- 64
- Pages
- 106-128
- ISSN
- 1364-0321 (ISSN-L)
- OpenAlex
- W2414929806
- Cited by
- 1,083
- References
- 114
- FWCI
- 50.41
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.