Printability and Shape Fidelity of Bioinks in 3D Bioprinting
Open accessThe DOI matches its Crossref record; 285 of the 287 references it cites were found in a registry or an index.
Abstract
Three-dimensional bioprinting uses additive manufacturing techniques for the automated fabrication of hierarchically organized living constructs. The building blocks are often hydrogel-based bioinks, which need to be printed into structures with high shape fidelity to the intended computer-aided design. For optimal cell performance, relatively soft and printable inks are preferred, although these undergo significant deformation during the printing process, which may impair shape fidelity. While the concept of good or poor printability seems rather intuitive, its quantitative definition lacks consensus and depends on multiple rheological and chemical parameters of the ink. This review discusses qualitative and quantitative methodologies to evaluate printability of bioinks for extrusion- and lithography-based bioprinting. The physicochemical parameters influencing shape fidelity are discussed, together with their importance in establishing new models, predictive tools and printing methods that are deemed instrumental for the design of next-generation bioinks, and for reproducible comparison of their structural performance.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Figures














Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The cited source says what the claim attributes to it.
In the citing paper
“To this end, considerable efforts were made in developing hydrogel-based inks or printing techniques to enhance 3D stability and shape fidelity, such as printing multimaterial inks with combined nozzle system24, 25, photo-crosslinkable hydrogels17, 26, 27, adding viscosifiers28–30, or printing in sacrificial supporting materials31–33.”
From Fibre-infused gel scaffolds guide cardiomyocyte alignment in 3D-printed ventricles (2023) · cites this paper as [30]
The cited source says what the claim attributes to it.
In the citing paper
“However, the successful fabrication of stable 3D constructs relies on hydrogels with optimized rheological behavior, structural stability, and physicochemical properties that ensure printability and shape fidelity [7,8,9].”
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
3D bioprinting of tissues and organs
Murphy, S. V., & Atala, A. (2014) · Nature Biotechnology · doi:10.1038/nbt.2958 · Cited by 7,034
Sydney Gladman, A., Matsumoto, E. A., Nuzzo, R. G., Mahadevan, L., & Lewis, J. A. (2016) · Nature Materials · doi:10.1038/nmat4544 · Cited by 3,027
Continuous liquid interface production of 3D objects
Tumbleston, J. R., Shirvanyants, D., Ermoshkin, N., Janusziewicz, R., Johnson, A. R., Kelly, D., Chen, K., Pinschmidt, R., Rolland, J. P., Ermoshkin, A., et al. (2015) · Science · doi:10.1126/science.aaa2397 · Cited by 2,278
3D bioprinting of vascularized, heterogeneous cell-laden tissue constructs
Kolesky, D. B., Truby, R. L., Gladman, A. S., Busbee, T. A., Homan, K. A., & Lewis, J. A. (2014) · Advanced Materials · doi:10.1002/adma.201305506 · Cited by 2,102
25th Anniversary Article: Engineering Hydrogels for Biofabrication
Malda, J., Visser, J., Melchels, F. P., Jüngst, T., Hennink, W. E., Dhert, W. J. A., Groll, J., & Hutmacher, D. W. (2013) · Advanced Materials · doi:10.1002/adma.201302042 · Cited by 1,901
Self-citationHinton, T. J., Jallerat, Q., Palchesko, R. N., Park, J. H., Grodzicki, M. S., Shue, H.-J., Ramadan, M. H., Hudson, A. R., & Feinberg, A. W. (2015) · Science Advances · doi:10.1126/sciadv.1500758 · Cited by 1,805
3D bioprinting of collagen to rebuild components of the human heart
Lee, A., Hudson, A. R., Shiwarski, D. J., Tashman, J. W., Hinton, T. J., Yerneni, S., Bliley, J. M., Campbell, P. G., & Feinberg, A. W. (2019) · Science · doi:10.1126/science.aav9051 · Cited by 1,782
Fibrinogen and fibrin structure and functions
MOSESSON, M. W. (2005) · Journal of Thrombosis and Haemostasis · doi:10.1111/j.1538-7836.2005.01365.x · Cited by 1,695
Bioinks for 3D bioprinting: an overview
Gungor-Ozkerim, P. S., Inci, I., Zhang, Y. S., Khademhosseini, A., & Dokmeci, M. R. (2018) · Biomaterials Science · doi:10.1039/c7bm00765e · Cited by 1,428
Multivascular networks and functional intravascular topologies within biocompatible hydrogels
Grigoryan, B., Paulsen, S. J., Corbett, D. C., Sazer, D. W., Fortin, C. L., Zaita, A. J., Greenfield, P. T., Calafat, N. J., Gounley, J. P., Ta, A. H., et al. (2019) · Science · doi:10.1126/science.aav9750 · Cited by 1,396
Research works printed but not linked: 5
- (126) Chimene, D.; Kaunas, R.; Gaharwar, A. K. Hydrogel Bioink Reinforcement for Additive Manufacturing: A Focused Review of Emerging Strategies. Adv. Mater. 2020 , 32 , 1902026. - · DOI · Paper page
- (129) Mezger, T. G. The Rheology Handbook , 3rd revised ed.; Vincentz Network, 2011. -
- (156) Petta, D.; Grijpma, D. W.; Alini, M.; Eglin, D.; D ' Este, M. Three-Dimensional Printing of a Tyramine Hyaluronan Derivative with Double Gelation Mechanism for Independent Tuning of Shear Thinning and Postprinting Curing. ACS Biomater. Sci. Eng. 2018 , 4 , 3088 -3098. - · DOI
- (161) Kiyotake, E. A.; Douglas, A. W.; Thomas, E. E.; Nimmo, S. L.; Detamore, M. S. Development and Quantitative Characterization of the Precursor Rheology of Hyaluronic Acid Hydrogels for Bioprinting. Acta Biomater. 2019 , 95 , 176. - · DOI · Paper page
- (245) ASTM52900-15, I. ; ASTM International: West Conshohocken, PA, 2015. -
Cited by
Items 301–400 of 1,001
Hao, L., Tao, X., Feng, M., Zhou, K., He, Y., Yang, J., Mao, H., & Gu, Z. (2023) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.3c00688 · Cited by 37
Photo-/thermo-responsive bioink for improved printability in extrusion-based bioprinting
Moon, S. H., Park, T. Y., Chi, H. J., & Yang, Y. J. (2024) · Materials Today Bio · doi:10.1016/j.mtbio.2024.100973 · Cited by 41
“The squareness of the pores within the grid structures determines the printability value (Pr) [117].”
BackgroundDiffusion‐Based 3D Bioprinting Strategies
Cai, B., Kilian, D., Mejia, D. R., Rios, R. J., Ali, A., & Heilshorn, S. C. (2023) · Advanced Science · doi:10.1002/advs.202306470 · Cited by 40
Microgel-based bioink for extrusion-based 3D bioprinting and its applications in tissue engineering
Iyer, K. S., Bao, L., Zhai, J., Jayachandran, A., Luwor, R. B., Li, J. J., & Li, H. (2025) · Bioactive Materials · doi:10.1016/j.bioactmat.2025.02.003 · Cited by 58
“…a cell-based bioink usually needs some biomaterial to offer protection from shear forces and to support the shape fidelity and mechanical properties of the printed constructs, while a biomaterial-based ink may need cells to provide biological activities and facilitate tissue regeneration [43].”
Innovative applications of multidimensional engineered hydrogels in wound healing
Hu, M., Zhang, Q., & Qin, L. (2025) · Journal of Advanced Research · doi:10.1016/j.jare.2025.08.006 · Cited by 40
Modelling Human Physiology on-Chip: Historical Perspectives and Future Directions
Pun, S., Haney, L. C., & Barrile, R. (2021) · Micromachines · doi:10.3390/mi12101250 · Cited by 39
López-Donaire, M. L., Izuzquiza, G. D. A., Garzon-Hernandez, S., Crespo‐Miguel, J., la Torre, M. F.-D., de Velasco, D. A. O.-G., & Garcia‐Gonzalez, D. (2022) · Advanced Materials Technologies · doi:10.1002/admt.202201707 · Cited by 36
3D printed tissue models: From hydrogels to biomedical applications
Cadamuro, F., Nicotra, F., & Russo, L. (2023) · Journal of Controlled Release · doi:10.1016/j.jconrel.2023.01.048 · Cited by 38
Fast Visible‐Light 3D Printing of Conductive PEDOT:PSS Hydrogels
Lopez‐Larrea, N., Gallastegui, A., Lezama, L. M., Criado‐Gonzalez, M., Casado, N., & Mecerreyes, D. (2023) · Macromolecular Rapid Communications · doi:10.1002/marc.202300229 · Cited by 36
Wang, D., Zeng, J., Zhu, H., Liu, S., Jia, L., Liu, W., Wang, Q., Wang, S., Liu, W., Zhou, J., et al. (2024) · Aggregate · doi:10.1002/agt2.477 · Cited by 37
Hydrogel-based inks for extrusion 3D printing: A rheological viewpoint
Thareja, P., Swarupa, S., Ahmad, S., & Jinugu, M. E. (2025) · Current Opinion in Colloid & Interface Science · doi:10.1016/j.cocis.2025.101918 · Cited by 34
Tang, X., Xu, H., Liu, X., Yang, Y., & Li, Z. (2025) · Frontiers in Bioengineering and Biotechnology · doi:10.3389/fbioe.2025.1707406 · Cited by 37
Biomaterial-minimalistic photoactivated bioprinting of cell-dense tissues
Wang, M., Li, W., Hao, J., Cai, L., Mei, X., Flores, R. S., Castillo, P., Garciamendez‐Mijares, C. E., Mu, X., Kuang, X., et al. (2025) · Cell · doi:10.1016/j.cell.2025.11.012 · Cited by 44
Guidelines for establishing a 3-D printing biofabrication laboratory
Sanicola, H. W., Stewart, C. E., Müller, M., Ahmadi, F., Wang, D., Powell, S. K., Sarkar, K., Cutbush, K., Woodruff, M. A., & Brafman, D. A. (2020) · Biotechnology Advances · doi:10.1016/j.biotechadv.2020.107652 · Cited by 40
“Many laboratories are introducing novel quantitative tests, qualitative tests, and predictive models for mainly extrusion-and lithography-based bioprinting [86].”
Shape Fidelity of 3D-Bioprinted Biodegradable Patches
Temirel, M., Hawxhurst, C. J., & Taşoğlu, S. (2021) · Micromachines · doi:10.3390/mi12020195 · Cited by 36
Theagarajan, R., Nimbkar, S., Moses, J. A., & Anandharamakrishnan, C. (2021) · Journal of Food Process Engineering · doi:10.1111/jfpe.13772 · Cited by 36
3D bioprinted colorectal cancer models based on hyaluronic acid and signalling glycans
Cadamuro, F., Marongiu, L., Marinò, M., Tamini, N., Nespoli, L. C., Zucchini, N., Terzi, A., Altamura, D., Gao, Z., Giannini, C., et al. (2022) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2022.120395 · Cited by 36
The Next Frontier of 3D Bioprinting: Bioactive Materials Functionalized by Bacteria
Liu, Y., Xia, X., Liu, Z., & Dong, M. (2022) · Small · doi:10.1002/smll.202205949 · Cited by 36
García‐Villén, F., Guembe, A., Rey, J. M., Zúñiga, T., Ruíz, S., del Burgo, L. S., Izco, J. M., Recalde, J. I., & Pedraz, J. L. (2023) · International Journal of Bioprinting · doi:10.18063/ijb.712 · Cited by 35
“The difference between 3D printing and 3D bioprinting lies not only in the final scope of the 3D construct produced but also in the composition of the so-called “ink”[4,12-15].”
BackgroundModeling a dynamic printability window on polysaccharide blend inks for extrusion bioprinting
Perin, F., Spessot, E., Famà, A., Bucciarelli, A., Callone, E., Mota, C., Motta, A., & Maniglio, D. (2023) · ACS Biomaterials Science & Engineering · doi:10.1021/acsbiomaterials.2c01143 · Cited by 33
Lazarus, E., Meyer, A. S., Ikuma, K., & Rivero, I. V. (2023) · Microbial Biotechnology · doi:10.1111/1751-7915.14360 · Cited by 35
“Several factors influence print fidelity, that is the geometric retention of a single extruded strand of bioink, as well as the printed part as a whole, as compared to the computer aided design model (CAD) (Schwab et al., 2020).”
MethodDecellularization and Their Significance for Tissue Regeneration in the Era of 3D Bioprinting
Gadre, M. A., Kasturi, M., Agarwal, P., & Vasanthan, K. S. (2024) · ACS Omega · doi:10.1021/acsomega.3c08930 · Cited by 53
Bioprinting of gelatin-based materials for orthopedic application
Waidi, Y. O., Kariim, I., & Datta, S. (2024) · Frontiers in Bioengineering and Biotechnology · doi:10.3389/fbioe.2024.1357460 · Cited by 34
Granular Biphasic Colloidal Hydrogels for 3D Bioprinting
Deo, K. A., Murali, A., Tronolone, J. J., Mandrona, C., Lee, H. P., Rajput, S., Hargett, S. E., Selahi, A., Sun, Y., Alge, D. L., et al. (2024) · Advanced Healthcare Materials · doi:10.1002/adhm.202303810 · Cited by 33
Zhu, J., Xie, F., Qiu, Z., & Chen, L. (2024) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2024.122438 · Cited by 33
Artificial Intelligence Informed Hydrogel Biomaterials in Additive Manufacturing
Zhang, Z., Tao, Z. Z., Du, R., Huo, R., & Zheng, X. (2025) · Gels · doi:10.3390/gels11120981 · Cited by 37
“Reports that harmonized units, temperatures, and illumination intensities and that recorded rheology methods and imaging thresholds reduced site effects that otherwise increased error by 10 to 30 percent when models trained in one laboratory were tested in another [3,38].”
InfluentialXiao, X., Jiang, X., Yang, S., Lu, Z., Niu, C., Xu, Y., Huang, Z., Kang, Y. J., & Feng, L. (2021) · Polymer · doi:10.1016/j.polymer.2021.123436 · Cited by 35
Serna, J. A., Rueda-Gensini, L., Céspedes-Valenzuela, D. N., Cifuentes, J., Cruz, J. C., & Muñoz-Camargo, C. (2021) · Polymers · doi:10.3390/polym13193263 · Cited by 36
Alginate-based bioink for organoid 3D bioprinting: A review
Leonardo, M., Prajatelistia, E., & Judawisastra, H. (2022) · Bioprinting · doi:10.1016/j.bprint.2022.e00246 · Cited by 34
Gwak, M. A., Lee, S. J., Lee, D., Park, S. A., & Park, W. H. (2022) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2022.12.124 · Cited by 35
Effect of sterilization techniques on biomaterial inks’ properties and 3D bioprinting parameters
Shyam, R., & Palaniappan, A. (2023) · Bioprinting · doi:10.1016/j.bprint.2023.e00294 · Cited by 35
Recent Advancements of Bioinks for 3D Bioprinting of Human Tissues and Organs
He, W., Deng, J., Ma, B., Tao, K., Zhang, Z., Ramakrishna, S., Yuan, W., & Ye, T. (2023) · ACS Applied Bio Materials · doi:10.1021/acsabm.3c00806 · Cited by 34
Cantoni, F., Barbe, L., Pohlit, H., & Tenje, M. (2024) · Advanced Materials Technologies · doi:10.1002/admt.202300718 · Cited by 33
Putri, K. N. A., Intasanta, V., & Hoven, V. P. (2024) · Heliyon · doi:10.1016/j.heliyon.2024.e25873 · Cited by 32
“As shear rates increase, surpassing the yield stress point ( τ y ), where G ʹ = G ʺ , disen-tanglement and chain reorientation to the bio-based polymer chain following the direction of applied forces start to happen [32].”
BackgroundInk-structing the future of vascular tissue engineering: a review of the physiological bioink design
Synofzik, J., Heene, S., Jonczyk, R., & Blume, C. A. (2024) · Bio-Design and Manufacturing · doi:10.1007/s42242-024-00270-w · Cited by 34
Zhang, Z., Chen, X., Gao, S., Fang, X., & Ren, S. (2024) · Cellular Oncology · doi:10.1007/s13402-024-00935-9 · Cited by 42
“Nonetheless, this printing strategy requires low-viscosity bioinks to achieve ideal droplet deposition, which may negatively influence print fidelity and cell encapsulation efficiency [57, 58].”
MethodOlate‐Moya, F., Rubí-Sans, G., Engel, E., Mateos‐Timoneda, M. A., & Palza, H. (2024) · Biomacromolecules · doi:10.1021/acs.biomac.3c01444 · Cited by 32
Amirian, J., Wychowaniec, J. K., D’Este, M., Vernengo, J., Metlova, A., Sizovs, A., Brangule, A., & Bandere, D. (2024) · Biomacromolecules · doi:10.1021/acs.biomac.4c00319 · Cited by 32
Self-citationDesign of biodegradable 3D-printed cardiovascular stent
Veerubhotla, K., & Lee, C. H. (2022) · Bioprinting · doi:10.1016/j.bprint.2022.e00204 · Cited by 32
Teixeira, M. C., Lameirinhas, N. S., Carvalho, J. P. F., Valente, B. F. A., Luís, J. L., Pires, L. S. O., Oliveira, H., Oliveira, J. M., Silvestre, A. J. D., Vilela, C., et al. (2022) · Nanomaterials · doi:10.3390/nano12132190 · Cited by 34
“, the decrease in shear viscosity with the increase in the shear rate applied, a typical behavior of non-Newtonian fluids [47].”
BackgroundMethodInfluentialCarvalho, J. P. F., Teixeira, M. C., Lameirinhas, N. S., Matos, F. S., Luís, J. L., Pires, L. S. O., Oliveira, H., Oliveira, J. M., Silvestre, A. J. D., Vilela, C., et al. (2023) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.3c07077 · Cited by 33
Ruchika, Bhardwaj, N., Yadav, S. K., & Saneja, A. (2024) · Drug Discovery Today · doi:10.1016/j.drudis.2024.103924 · Cited by 35
Biofabrication of engineered blood vessels for biomedical applications
Laowpanitchakorn, P., Zeng, J., Piantino, M., Uchida, K., Katsuyama, M., & Matsusaki, M. (2024) · Science and Technology of Advanced Materials · doi:10.1080/14686996.2024.2330339 · Cited by 31
“Extrusion-based printing is another type of 3D printing and uses pneumatic pressure, mechanical force, or thermal extrusion rotation to deposit the bioink loaded in cartridges into a columnar or rod-like structure [191].”
MethodKoumentakou, I., Michopoulou, A., Noordam, M. J., Terzopoulou, Z. N., & Bikiaris, D. Ν. (2024) · Journal of Materials Science · doi:10.1007/s10853-024-09707-0 · Cited by 33
“While the term is not strictly defined, it is used to describe, among other things, screening processes from macroscopic and microscopic images of 3D-printed constructs with the goal of choosing printing parameters and comparing different bio-materials inks [22].”
Wu, Y., Li, Z., Yang, L., Zheng, H., & Xue, C. (2024) · Food Hydrocolloids · doi:10.1016/j.foodhyd.2024.110242 · Cited by 31
Advanced optical assessment and modeling of extrusion bioprinting
Lamberger, Z., Schubert, D. W., Büchner, M., Chicaiza-Cabezas, N. A., Schrüfer, S., Murenu, N., Schaefer, N., & Lang, G. (2024) · Scientific Reports · doi:10.1038/s41598-024-64039-y · Cited by 31
“Schwab et al. mention parameters like flow behavior, yield stress, elastic recovery, shear stress, and damping factor tanδ 7 .”
BackgroundApplication of 3D-Printed Bioinks in Chronic Wound Healing: A Scoping Review
Abuhamad, A. Y., Masri, S., Fadilah, N. I. M., Alamassi, M. N., Maarof, M., & Fauzi, M. B. (2024) · Polymers · doi:10.3390/polym16172456 · Cited by 31
“Characteristics of 3D Bioprinting Techniques The bioprinting techniques utilized across the studies demonstrated high print fidelity and stability, which are crucial for maintaining the structural integrity of the printed constructs [64].”
MethodNanotechnologies and Nanomaterials in 3D (Bio)printing toward Bone Regeneration
Wang, Z., Agrawal, P. S., & Zhang, Y. S. (2021) · Advanced NanoBiomed Research · doi:10.1002/anbr.202100035 · Cited by 34
Bednarzig, V., Schrüfer, S., Schneider, T. C., Schubert, D. W., Detsch, R., & Boccaccini, A. R. (2022) · International Journal of Molecular Sciences · doi:10.3390/ijms23094750 · Cited by 34
“Equation (4) for calculation of the Us [36].”
BackgroundHeidari, F., Saadatmand, M., & Simorgh, S. (2023) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2023.127041 · Cited by 31
Three-dimensional printed sodium alginate clay nanotube composite scaffold for bone regeneration
Zhou, Y., Gao, X., Zhao, M., Li, L., & Liu, M. (2024) · Composites Science and Technology · doi:10.1016/j.compscitech.2024.110537 · Cited by 33
Wu, D., Pang, S., Berg, J., Mei, Y., Ali, A. S. M., Röhrs, V., Tolksdorf, B., Hagenbuchner, J., Ausserlechner, M. J., Deubzer, H. E., et al. (2024) · Advanced Functional Materials · doi:10.1002/adfm.202314171 · Cited by 37
Ionically annealed zwitterionic microgels for bioprinting of cartilaginous constructs
Surman, F., Asadikorayem, M., Weber, P., Weber, D. M., & Zenobi‐Wong, M. (2024) · Biofabrication · doi:10.1088/1758-5090/ad1b1f · Cited by 31
“Shape preservation of the bioink occurs after extrusion, with increasing viscosity where the shear rate drops [64].”
BackgroundSoft Actuators and Actuation: Design, Synthesis, and Applications
Kalulu, M., Chilikwazi, B., Hu, J., & Fu, G. (2024) · Macromolecular Rapid Communications · doi:10.1002/marc.202400282 · Cited by 43
Differential Responses to Bioink-Induced Oxidative Stress in Endothelial Cells and Fibroblasts
Genç, H., Hazur, J., Karakaya, E., Dietel, B., Bider, F., Gröll, J., Alexiou, C., Boccaccini, A. R., Detsch, R., & Cicha, I. (2021) · International Journal of Molecular Sciences · doi:10.3390/ijms22052358 · Cited by 30
“This young research field encounters several challenges, one of which is related to the composition and properties of the bioinks that must serve as extracellular matrices (ECM) for cell organization [1].”
Kumar, S. (2021) · Materials Advances · doi:10.1039/d1ma00525a · Cited by 33
Netti, F., Aviv, M., Dan, Y., Rudnick‐Glick, S., Halperin‐Sternfeld, M., & Adler‐Abramovich, L. (2022) · Nanoscale · doi:10.1039/d1nr08206j · Cited by 30
Space‐Efficient 3D Microalgae Farming with Optimized Resource Utilization for Regenerative Food
Liu, H., Yu, S., Liu, B., Xiang, S., Jiang, M., Yang, F., Tan, W., Zhou, J., Xiao, M., Li, X., et al. (2024) · Advanced Materials · doi:10.1002/adma.202401172 · Cited by 44
Rheological Basics for Modeling of Extrusion Process of Wood Polymer Composites
Wilczyński, K. J., Buziak, K., Lewandowski, A., Nastaj, A., & Wilczyński, K. J. (2021) · Polymers · doi:10.3390/polym13040622 · Cited by 31
Carpio, M. B., González‐Martínez, E., Dabaghi, M., Ungureanu, J., Tafoya, A. A., Martinez, D. A. G., Hirota, J. A., & Moran-Mirabal, J. M. (2023) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.3c10092 · Cited by 30
Towards single-cell bioprinting: micropatterning tools for organ-on-chip development
Bosmans, C., Rodriguez, N. G., Karperien, M., Malda, J., Teixeira, L. M., Levato, R., & Leijten, J. (2024) · Trends in biotechnology · doi:10.1016/j.tibtech.2023.11.014 · Cited by 30
Self-citationMakurat-Kasprolewicz, B., Ipakchi, H., Rajaee, P., Ossowska, A., Hejna, A., Farokhi, M., Mottaghitalab, F., Pawlak, M., Rabiee, N., Belka, M., et al. (2024) · Chemical Engineering Journal · doi:10.1016/j.cej.2024.152703 · Cited by 25
Wu, Y., Fortunato, G. M., Okesola, B. O., di Brocchetti, F. L. P., Suntornnond, R., Connelly, J. T., Maria, C. D., Rodríguez‐Cabello, J. C., Vozzi, G., Wang, W., et al. (2021) · Biofabrication · doi:10.1088/1758-5090/abe4c3 · Cited by 34
“Bioinks are increasingly playing a leading role in the quest for recreating the structures and functions of biological systems [1].”
BackgroundOlmos‐Juste, R., Guaresti, O., Calvo‐Correas, T., Gabilondo, N., & Eceiza, A. (2021) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2021.121124 · Cited by 29
Sakai, S., Kotani, T., Harada, R., Goto, R., Morita, T., Bouissil, S., Dubessay, P., Pierre, G., Michaud, P., Elboutachfaiti, R., et al. (2021) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2021.118820 · Cited by 29
Impact of Cell Loading of Recombinant Spider Silk Based Bioinks on Gelation and Printability
Lechner, A., Trossmann, V. T., & Scheibel, T. (2021) · Macromolecular Bioscience · doi:10.1002/mabi.202100390 · Cited by 32
Amini, M., Kamkar, M., Ahmadijokani, F., Ghaderi, S., Rojas, O. J., Hosseini, H., & Arjmand, M. (2022) · Biomacromolecules · doi:10.1021/acs.biomac.2c01241 · Cited by 32
Jeon, E. Y., Chun, Y. G., & Kim, B. (2023) · Journal of Food Engineering · doi:10.1016/j.jfoodeng.2023.111777 · Cited by 28
Chemical Circularity in 3D Printing with Biobased Δ‐Valerolactone
Yue, L., Su, Y., Li, M., Yu, L., Sun, X., Cho, J., Brettmann, B. K., Gutekunst, W. R., Ramprasad, R., & Qi, H. J. (2024) · Advanced Materials · doi:10.1002/adma.202310040 · Cited by 30
Dynamic bioinks for tissue/organ bioprinting: Principle, challenge, and perspective
Ma, D., Lu, W. W., Liu, W., Liu, W., & Ruan, C. (2025) · Progress in Materials Science · doi:10.1016/j.pmatsci.2025.101527 · Cited by 31
3D Printing of Conducting Polymer Hydrogels for Electrostimulation‐Assisted Tissue Engineering
Tran, C. M., Yue, Z., Qin, C., Imani, K. B. C., Dottori, M., Forster, R. J., & Wallace, G. G. (2025) · Advanced Materials · doi:10.1002/adma.202507779 · Cited by 32
Pioneering 3D and 4D Bioprinting Strategies for Advanced Wound Management: From Design to Healing
Yadav, A. K., Verma, D., Thakkar, S., Rana, Y., Banerjee, J., Bhatia, D. D., & Banerjee, S. (2025) · Small · doi:10.1002/smll.202506259 · Cited by 32
Characterization of κ‐carrageenan/methylcellulose/cellulose nanocrystal hydrogels for 3D bioprinting
Boonlai, W., Tantishaiyakul, V., & Hirun, N. (2021) · Polymer International · doi:10.1002/pi.6298 · Cited by 28
Biodegradable Inks in Indirect Three-Dimensional Bioprinting for Tissue Vascularization
Ze, Y., Li, Y., Huang, L., Shi, Y., Li, P., Gong, P., Lin, J., & Yao, Y. (2022) · Frontiers in Bioengineering and Biotechnology · doi:10.3389/fbioe.2022.856398 · Cited by 30
“Viscosity and rheological properties greatly influence the printability of the bioinks, and they are mainly determined by the molecular weight and concentration of polymer in solution (Schwab et al., 2020).”
BackgroundGarcía‐Villén, F., Zárraga, F. L., Viseras, C., Ruíz, S., Khalak, F. A.-H., Diez-Aldama, I., del Burgo, L. S., Scaini, D., & Pedraz, J. L. (2023) · International Journal of Bioprinting · doi:10.18063/ijb.v9i2.664 · Cited by 29
“In this extrusion method, air flow propels the ink through the nozzle[51,52].”
MethodWu, Y. B., Yang, X., Gupta, D., Alioglu, M. A., Qin, M., Özbolat, V., Li, Y., & Ozbolat, I. T. (2024) · Advanced Functional Materials · doi:10.1002/adfm.202313088 · Cited by 38
4D printing of semi-crystalline crosslinked polymer networks with two-way shape-memory effect
Bonetti, L., Natali, D., Pandini, S., Messori, M., Toselli, M., & Scalet, G. (2024) · Materials & Design · doi:10.1016/j.matdes.2024.112725 · Cited by 29
Puistola, P., Kethiri, A. R., Nurminen, A., Turkki, J. A., Hopia, K., Miettinen, S., Mörö, A., & Skottman, H. (2024) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.3c17803 · Cited by 30
“61 Here, our novel corneal-stroma-specific bioink demonstrated shear-thinning in viscosity measurements.”
BackgroundA review of 3D bioprinting for organoids
Li, Z., Chen, L., Wu, J., Chen, Y., Zhu, Y. Z., Li, G., Xie, G., Tang, G., & Xie, M. (2025) · Medical Review · doi:10.1515/mr-2024-0089 · Cited by 35
Stereolithographic Visible-Light Printing of Poly( l -glutamic acid) Hydrogel Scaffolds
Viray, C. M., van Magill, B., Zreiqat, H., & Ramaswamy, Y. (2022) · ACS Biomaterials Science & Engineering · doi:10.1021/acsbiomaterials.1c01519 · Cited by 29
Recent progresses in novel in vitro models of primary neurons: A biomaterial perspective
Zhang, J., Yang, H., Wu, J., Zhang, D., Wang, Y., & Zhai, J. (2022) · Frontiers in Bioengineering and Biotechnology · doi:10.3389/fbioe.2022.953031 · Cited by 37
“In addition to the major characteristics suitable for cell culture as mentioned in the scaffold-based model section, bioinks used in 3D bioprinting are also required to have good printability and shape fidelity to adapt to the biofabrication process (Schwab et al., 2020).”
BackgroundPrint parameter optimisation for a Pluronic F-127 and alginate hybrid hydrogel
Hibbert, M., Viljoen, J. M., & Plessis, D. (2022) · Bioprinting · doi:10.1016/j.bprint.2022.e00257 · Cited by 27
Crystalline and Hairy Nanocelluloses for 3D Printed Hydrogels and Strongly Structured Cryogels
Ojagh, S. M. A., Amini, M., Cranmer-Smith, S., Vahabzadeh, F., Arjmand, M., Tam, K. C., Rojas, O. J., Kamkar, M., & van de Ven, T. G. M. (2023) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.3c00180 · Cited by 28
Material extrusion of sodium polyacrylate superabsorbent polymer
Gosden, D., Studley, M., & Rossiter, J. M. (2023) · Additive manufacturing · doi:10.1016/j.addma.2023.103886 · Cited by 36
Polymeric nanomaterials in 3D bioprinting for tissue engineering and drug delivery applications
Han, S., Fisher, J. P., Mikos, A. G., & Hogan, K. J. (2024) · Bioprinting · doi:10.1016/j.bprint.2024.e00345 · Cited by 30
Lan, X., Ma, Z., Dimitrov, A., Kunze, M., Mulet‐Sierra, A., Ansari, K., Osswald, M., Seikaly, H. R., Boluk, Y., & Adesida, A. B. (2024) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2024.132819 · Cited by 27
Niclot, F. B., Montalbano, G., Fiorilli, S., & Vitale‐Brovarone, C. (2021) · International Journal of Molecular Sciences · doi:10.3390/ijms22041718 · Cited by 27
“s when increasing shear rates were applied, proving the shear thinning behavior of the system, a key feature for the material inks used for extrusion printing technologies [95,96].”
Constraint based Bayesian optimization of bioink precursor: a machine learning framework
Xu, Y., Sarah, R., Habib, A., Liu, Y., & Khoda, B. (2024) · Biofabrication · doi:10.1088/1758-5090/ad716e · Cited by 31
“Precision with high resolution and shape fidelity is essential to mimic the shape and architecture of a specific tissue or an organ during constructs printing [22].”
Polez, R. T., Kimiaei, E., Madani, Z., Österberg, M., & Baniasadi, H. (2024) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2024.136182 · Cited by 26
Morgan, F. L. C., Beeren, I. A. O., Bauer, J., Moroni, L., & Baker, M. B. (2024) · Journal of the American Chemical Society · doi:10.1021/jacs.4c08099 · Cited by 28
Herrada‐Manchón, H., Celada, L., Rodríguez-González, D., Fernández, M. A., Aguilar, E., & Chiara, M. (2021) · Materials Science and Engineering C · doi:10.1016/j.msec.2021.112357 · Cited by 25
Herrada‐Manchón, H., Rodríguez-González, D., Fernández, M. A., Kucko, N. W., Groot, F. B., & Aguilar, E. (2022) · Gels · doi:10.3390/gels8010028 · Cited by 30
“γ )n), where τ0 is the yield stress (Pa) below which there is no flow, K is the consistency index (Pa·sn), and n is the flow index that defines the degree of non-Newtonian behavior (shear thickening for n > 1 and shear thinning for n < 1) [42,53].”
BackgroundChen, H., Ahmad, T., Haider, M. S., Hahn, L., Stahlhut, P., Gröll, J., & Luxenhofer, R. (2021) · Biofabrication · doi:10.1088/1758-5090/ac40ee · Cited by 26
“Rheological measurements were carried out to understand the viscoelastic behavior and estimate the print-ability of the hydrogel precursor solutions [49, 50].”
Montalbano, G., Calore, A. R., & Vitale‐Brovarone, C. (2023) · Journal of Applied Polymer Science · doi:10.1002/app.53593 · Cited by 27
Choi, K. K., Park, C. Y., Choi, J. S., Kim, Y., Chung, S. H., Lee, S., Kim, C., & Park, S. J. (2023) · Tissue Engineering and Regenerative Medicine · doi:10.1007/s13770-023-00545-w · Cited by 30
Valorization of agar production residue as a filler in soy protein hydrogels for 3D printing
Uranga, J., Carranza, T., Peñalba, M., de la Caba, K., & Guerrero, P. (2023) · International Journal of Bioprinting · doi:10.18063/ijb.731 · Cited by 30
“Although there is no consensus on how to grade printability and objectively/quantitatively describe shape fidelity[24], based on the rheological results obtained, it could be concluded that the 3D-printed products prepared in this work present good shape fidelity (Figure 2).”
Preclinical Testing Techniques: Paving the Way for New Oncology Screening Approaches
van Rijt, A., Stefanek, E., & Valente, K. P. (2023) · Cancers · doi:10.3390/cancers15184466 · Cited by 31
“…m can be achieved through extrusion bioprinting, and Resolutions of 100–600 µm can be achieved through extrusion bioprinting, and producing intricate structures such as vascular networks can be challenging [31,32]. producing intricate structures such as vascular networks can be challenging [31,32].”
BackgroundTackling current production of HAp and HAp-driven biomaterials
Veiga, A., Madureira, S., Costa, J. B., Castro, F., Rocha, F. A., & Oliveira, A. L. (2023) · Materials Advances · doi:10.1039/d3ma00363a · Cited by 28
Elomaa, L., Almalla, A., Keshi, E., Hillebrandt, K. H., Sauer, I. M., & Weinhart, M. (2023) · Biomaterials and Biosystems · doi:10.1016/j.bbiosy.2023.100084 · Cited by 36
“Moreover, cells transform a bioink into a composite material that may behave as a colloidal system and exhibit enhanced shear-thinning behavior [63].”
BackgroundKitana, W., Levario‐Diaz, V., Cavalcanti‐Adam, E. A., & Ionov, L. (2023) · Advanced Healthcare Materials · doi:10.1002/adhm.202303343 · Cited by 26
Metadata
- Authors
- Schwab, A., Levato, R., D’Este, M., Piluso, S., Eglin, D., & Malda, J.
- Affiliations
- AO Foundation (CH)
- Utrecht University (NL)
- Corresponding author
- Malda, Jos
- Venue
- Chemical Reviews
- Publisher
- American Chemical Society (ACS)
- Published
- 2020-08-28
- Volume
- 120
- Issue
- 19
- Pages
- 10850-10877
- ISSN
- 0009-2665 (ISSN-L)
- 1520-6890
- PMC
- PMC7564085
- OpenAlex
- W3082213210
- Cited by
- 1,359
- References
- 287
- Citations by year
- 2026: 305 · 2025: 283 · 2024: 280 · 2023: 202 · 2022: 176 · 2021: 107 · 2020: 6
- FWCI
- 10.29
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Licence
- Locations
- Chemical Reviews (publishedVersion, cc-by-nc-nd)
- PubMed Central (publishedVersion)
- PubMed (publishedVersion)
- University of Twente Research Information (publishedVersion, cc-by-nc-nd)
- HAL (submittedVersion)
- Utrecht University Repository (Utrecht University) (submittedVersion, other-oa)
- University of Twente Research Information (submittedVersion, cc-by-nc-nd)
- Funders
- AO Foundation (3D OC)
- Nederlandse Organisatie voor Wetenschappelijk Onderzoek (024.003.013)
- ReumaNederland (LLP12, LLP22)
- Topics
- Physical Sciences › Engineering › Biomedical Engineering › 3D Printing in Biomedical Research
- Physical Sciences › Materials Science › Biomaterials › Hydrogels: synthesis, properties, applications
- Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Additive Manufacturing and 3D Printing Technologies
- Keywords
- bioinks, 3D bioprinting, printability, shape fidelity, hydrogels, extrusion-based bioprinting, rheology, physicochemical parameters, prediction model
- MeSH terms
- Humans, Ink, Tissue Engineering, Bioprinting, Printing, Three-Dimensional
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.