The DOI matches its Crossref record; 301 of the 306 references it cites were found in a registry or an index, and 5 are not checked yet; 46 of the 136 sources its claims cite were checked for support.
Metal Oxide Thin Films for Advanced Photonic Applications
Open accessAbstract
Oxide materials represent a versatile and fundamental platform for photonics, allowing the manipulation of light through optical property engineering. This review focuses mainly on the physics and applications of simple oxides, analysing their use in the realisation of dielectric mirrors, in particular of distributed Bragg reflectors, and planar microcavities. Critical aspects regarding the design of multilayer structures, the control of optical confinement and the improvement of the quality factor in passive devices are discussed. However, to provide a complete picture of the evolution of the field, the section dedicated to oxide materials anticipates future directions dominated by complex oxides such as lithium niobate, lithium tantalate and barium titanate required for active photonics. In this context, a necessary technological paradigm shift is highlighted: the transition from the current use of film-on-insulator platforms to the direct epitaxial growth of these functional materials, an essential step for the scalability and monolithic integration of future photonic devices.
Verified 2026-10-08 · 5 references not checked yet
Overview
CoChat Summary
TL;DR
This review surveys metal-oxide thin films for advanced photonics, focusing on dielectric mirrors, distributed Bragg reflectors (DBRs), and planar microcavities, while also previewing complex oxides for active photonics. It argues that material pair, deposition technique, and architecture govern mirror reflectivity and cavity quality factor, and that future scalability requires a shift toward direct epitaxial growth.
Key findings
- DBR performance depends strongly on optical contrast and pair number: examples include SiO₂/ZrO₂ with R ≥ 95% at 366 nm and PBG 82 nm for an eight-pair structure; SiO₂/Al₂O₃ with R ≥ 97% at 290 nm; Al₂O₃/ZrO₂ with R = 99.8% at 377 nm for a 12.5-pair structure; Al₂O₃/YSZ with R = 99.7% for 10-period bilayer films; Al₂O₃/TiO₂ with R = 98.1% at 471 nm and PBG 79 nm for six-period bilayer films; and SiO₂/TiO₂ with 99.99% and tuneable PBG from visible to NIR via sol-gel spin coating.
- Refractive indices vary by deposition method: SiO₂ shows n = 1.46–1.52 at 633 nm by PLD, 1.41–1.52 by RF magnetron sputtering, and 1.43–1.49 by e-beam evaporation; TiO₂ shows n = 2.6 at 550 nm by PLD, 2.57–2.74 by RF magnetron sputtering, and 2.06–2.08 by e-beam evaporation.
- Planar microcavity quality factors in Table 8 range widely, e.g., SiO₂/HfO₂/Al with ZnO active layer Q = 4250; SiO₂/HfO₂ with HfO₂ Q = 3700; Al₂O₃/YSZ with ZnO Q = 1000; SiO₂/Ta₂O₅ with organics Q = 1000; SiO₂/TiO₂ with Er³⁺-doped SiO₂ Q = 890; and SiO₂/TiO₂ with TiO₂ Q = 35.
- Complex oxides are highlighted for active photonics: LiNbO₃ has r₃₃ = 30.9 pm/V, d₃₃ = 27 pm/V, n ≈ 2.2 ordinary and 2.1 extraordinary, and transparency from 0.4 to 5.5 µm; LiTaO₃ has r₃₃ = 30.5 pm/V and bandgap 3.93 eV; BaTiO₃ has a Pockels coefficient larger than 1000 pm/V and transparency from 460 to 6300 nm.
Methods
- This is a review article; the Data Availability Statement says “No new data were created or analysed in this study.”
- It synthesizes literature on oxide thin-film processing, dielectric mirrors/DBRs, and planar optical microcavities, with tables comparing material pairs, refractive indices, deposition processes, and microcavity Q factors.
- The main analysis is qualitative and comparative, discussing PVD, CVD, and solution-based routes, and linking deposition method to film density, refractive index, stress, optical losses, and device performance.
Limitations
- The paper states that planar Fabry–Pérot cavities generally offer less spatial confinement (larger V_eff) and more modest temporal confinement (lower Q) than whispering gallery resonators and complex photonic structures, and that their architecture limits confinement effects.
- It states that large-scale deposition studies are scarce because of challenges in obtaining uniform films on large surfaces, stress-induced defects, time and manufacturing cost, and difficult metrology on large surfaces.
- Evident from the text: as a review, it provides no original experimental validation, and it notes method-specific drawbacks such as solution-based poor interface quality and porosity, CVD high temperatures, PVD higher cost, and MBE infrastructure/high-vacuum requirements with lower growth rates.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
29 Valid · 8 Not valid · 42 Not checked · 29 Own results and interpretations
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Owing to a broad-spectrum transparency and high thermal and chemical stability, tantalum pentoxide (Ta2O5) is among the high-refractive-index materials frequently used in optical coatings, from antireflective to guiding thin films (cores) in waveguides operating at high temperatures [45-48].”
What the sources say
- Not checked — no full text of the sourcecites [45] Belt, 2017, Ultra-Low-Loss Ta2O5-Core/SiO2-Clad Planar Waveguides on Si Substrates, Optica source
- Not checked — no full text of the sourcecites [46] Pal, 2023, Sol-Gel Prepared Amorphous Ta2O5 Thin Film for Application in High LIDT Antireflection Coating and UV Photodetection, Opt. Mater. source
- Not checked — no full text of the sourcecites [47] Vernhes, 2014, Reactive HiPIMS Deposition of SiO2/Ta2O5 Optical Interference Filters, J. Appl. Phys. source
- Partly supportedcites [48] Pal, 2025, Sol-Gel Dip Coating of Ta2O5/SiO2 Anti-Reflection Films on Fused Silica for Developing Laser Optics with High Laser Induced Damage Threshold, J. Solgel Sci. Technol. sourceExperimental — accuracy not yet measured
Section 3.3 (page unavailable) reports a higher refractive index for the Ta2O5 film than for SiO2, and Section 3.5 describes Ta2O5/SiO2 antireflection coatings at four wavelengths. The cited paper does not establish that Ta2O5 is frequently used as a guiding core in high-temperature waveguides, or attribute that range of uses to broad-spectrum transparency and high thermal and chemical stability. (LLM, conf=0.86)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“The most commonly used material to fabricate dielectric mirrors is silicon dioxide (SiO2).”
What the sources say
- Not checked — no full text of the sourcecites [27] Manikanta, R.V., Mahesh, C.U., and Yepuri, V. (2025). Light Matters: Fabrication and Investigation of Optical and Wetting Properties of TiO2/SiO2 Multilayer Structure. J. Opt. source
- Not checked — no full text of the sourcecites [28] Chichibu, 2006, Dielectric SiO2/ZrO2 Distributed Bragg Reflectors for ZnO Microcavities Prepared by the Reactive Helicon-Wave-Excited-Plasma Sputtering Method, Appl. Phys. Lett. source
- Not checked — no full text of the sourcecites [29] Cui, 2022, Conductive SiO2/HfO2 distributed Bragg Reflector Achieved by Electrical Breakdown and Its Application in GaN-Based Light Emitters, J. Appl. Phys. source
- Partly supportedcites [30] Robinson, 2021, Thermal Noise and Mechanical Loss of SiO2/Ta2O5 Optical Coatings at Cryogenic Temperatures, Opt. Lett. sourceExperimental — accuracy not yet measured
The introduction (p. 1) says SiO2 and Ta2O5 are the most common choices for the low- and high-refractive-index layers of highly reflective optical coatings, respectively. This supports SiO2 as a common mirror-coating material, but not the claim that it alone is the most commonly used material for dielectric mirrors. (LLM, conf=0.84)
- Partly supportedcites [31] Kim, S., In, J.H., Kim, S.H., Han, K., Lim, D., Hwang, Y.S., Lee, K.M., and Choi, J.H. (2023). Study of High Transmittance of SiO2/Nb2O5 Multilayer Thin Films Deposited by Plasma-Assisted Reactive Magnetron Sputtering. Appl. Sci., 13. sourceExperimental — accuracy not yet measured
The Introduction (page unavailable) calls SiO2 a well-known low-refractive-index material in optical multilayer systems, and the Results and Discussion describe SiO2-containing commercial coatings. These passages support its use in such coatings, but do not establish that it is the most commonly used material for dielectric mirrors. (LLM, conf=0.82)
- Not checked — no full text of the sourcecites [32] Grilli, 2009, Al2O3/SiO2 and HfO2/SiO2 Dichroic Mirrors for UV Solid-State Lasers, Thin Solid Films source
- Not checked — no full text of the sourcecites [33] Jiang, 2024, High-Performance SiO2-SiNx Distributed Bragg Reflectors Fabricated by Ion-Assisted Reactive Magnetron Sputtering, Vacuum source
- Partly supportedcites [34] Steinlechner, 2014, Optical Absorption Measurement at 1550nm on a Highly-Reflective Si/SiO2 Coating Stack, Class. Quantum Gravity sourceExperimental — accuracy not yet measured
The Introduction (p. 1) describes silica (SiO2) and tantala as the materials in well-established dielectric mirror coatings for gravitational-wave detectors. This supports SiO2 as an established mirror-coating material, but not the broader claim that it is the most commonly used material for dielectric mirrors generally. (LLM, conf=0.85)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
Every source the paper cites for this claim was checked and supports it.
In the paper
“Recent studies [156] have also shown that the gas flow during ICPVD deposition is the primary parameter that can adjust the stress in SiO2 thin films between tensile and compressive states, whilst not significantly altering the refractive index of the material.”
What the sources say
- Supportedcites [156] Wostbrock, N., and Busani, T. (2020). Stress and Refractive Index Control of SiO2 Thin Films for Suspended Waveguides. Nanomaterials, 10. source
The Conclusions identify gas flowrate as the primary variable for depositing tensile or compressive SiO2 films without significantly affecting refractive index. The Results specify that refractive index remained unchanged as flowrate varied within a given gas ratio. (LLM, conf=0.94)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“For example, in the case of PLD, 'atomic peening' and collision-induced densification result in compressive stress [153].”
What the sources say
- Partly supportedcites [153] Chason, 2016, A Kinetic Model for Stress Generation in Thin Films Grown from Energetic Vapor Fluxes, J. Appl. Phys. sourceExperimental — accuracy not yet measured
The Introduction (page unavailable) identifies pulsed laser deposition as an energetic deposition process and says energetic bombardment may cause atomic peening, compressive stress, and collision-induced densification. The Kinetic Model section (page unavailable) links collision-induced densification to compressive stress. The paper does not establish that both mechanisms result in compressive stress specifically in PLD; its wording about peening is also qualified as a possibility. (LLM, conf=0.82)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Another key feature to take into account is that, in the case of manufacturing DBRs on large wafers, the stress appears due to the interactions of the thin film and the substrate curvature, resulting in a nonlinear stress distribution across the wafer [151].”
What the sources say
- Partly supportedcites [151] Sun, 2018, Investigation for the Structural Stress of SiO2 Thin Films and Its Distribution on the Large-Wafer Created by Plasma Enhanced Chemical Vapor Deposition, AIP Adv. sourceExperimental — accuracy not yet measured
Section II says interactions among film layers and the substrate generate structural stress that depends on curvature and position across the wafer. The Conclusions report a nonlinear distribution of structural stress. The paper studies PECVD SiO₂ films on large silicon wafers, however, and does not establish the finding specifically for DBR manufacturing. (LLM, conf=0.86)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
27 more claims · 3 with their cited sources checked
Create a free account to see all 108 claims and every source verdict.
- It may state two separate claims as one. 55
- Probably not a substantial claim. 35
- Borderline: one of the tests for a substantial claim is unclear. 1
- The quote only partly states this claim. 2
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ 2. Oxide Materials and Their Subsequent Functionalization for Dielectric Coatings
“| PVD | Electron cyclotron resonance ion beam deposition Electron beam evaporation (e-beam) Radio frequency magnetron sputtering (RF magnetron) Pulsed laser deposition (PLD) | 1.74-1.95 2.0419 <2.2 >2.2 | - - >5 × 10 - 4 | [72] [73] [74] [75] |”
§ References
“75. Zhang, J.Y.; Boyd, I.W. Thin Tantalum and Tantalum Oxide Films Grown by Pulsed Laser Deposition.”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ 2.2. Thin Film Properties for Dielectric Mirrors
“In contrast to the e-beam technique, magnetron sputtering can provide values higher than n = 2.24 at λ = 550 nm for TiO2 films, even at room temperature [150].”
§ References
“150. Zhao, Z.; Tay, B.K.; Yu, G. Room-Temperature Deposition of Amorphous Titanium Dioxide Thin Film with High Refractive Index by a Filtered Cathodic Vacuum Arc Technique.”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ 2.3. Stoichiometrically Complex Oxides with Optically Tunable Properties Under Electrical, Mechanical or Acoustic Excitation
“This material shows an enhanced chemical stability by simply replacing the Nb atoms with Ta atoms [184], as well as a wider bandgap (3.93 eV [185]), facilitating nonlinear optical conversion in the Vis and UV regions [186].”
§ References
“185. Zanatta, A.R. The Optical Bandgap of Lithium Niobate (LiNbO3) and Its Dependence with Temperature.”
Cited works that were retracted
Works this paper cites that were later retracted, from the retraction notices publishers deposit. Major when the notice came out before this paper was published.
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
Cited work 10.1002/pssa.200306153 · retracted 2004-12-13 · notice 10.1002/pssa.200406923 · this paper published 2026-02-27
Citations
Cites
1 retracted
ZnO as a material mostly adapted for realization of room-temperature polariton lasers
Zamfirescu, M., Kavokin, A., Gil, B., & Malpuech, G. (2003) · physica status solidi (a) · doi:10.1002/pssa.200306153
RetractedVahala, K. J. (2003) · Nature · doi:10.1038/nature01939 · Cited by 4,878 · cited 1×
“These microstructures can alter the local photonic density of states (LPDOS) owing to their inherent resonance modes, which can be designed by choosing the component materials, geometry and dimensions [248,249].”
Exceptional points enhance sensing in an optical microcavity
Chen, W., Kaya Özdemir, Ş., Zhao, G., Wiersig, J., & Yang, L. (2017) · Nature · doi:10.1038/nature23281 · Cited by 2,084 · cited 1×
“…these microresonators have gained increased attention from researchers over the years due to their light coupling, enabling their utilisation in many applications, such as filters [250,251], lasers [252], sensors [253,254] and optoelectronic devices such as organic solar cells [232,255].”
Integrated photonics on thin-film lithium niobate
Zhu, D., Shao, L., Yu, M., Cheng, R., Desiatov, B., Xin, C. J., Hu, Y., Holzgrafe, J., Ghosh, S., Shams-Ansari, A., et al. (2021) · Advances in Optics and Photonics · doi:10.1364/aop.411024 · Cited by 1,516 · cited 1×
“For a detailed presentation of TFLN-based photonics, there are several publications in the literature dedicated to this topic in recent years [174–179].”
BaTiO3-Based Piezoelectrics: Fundamentals, Current Status, and Perspectives
Acosta, M., Novak, N., Rojas, V., Patel, S., Vaish, R., Koruza, J., Rossetti, G. A., & Rödel, J. (2017) · Applied Physics Reviews · doi:10.1063/1.4990046 · Cited by 1,451 · cited 1×
“Other applications include capacitors, sensors, transducers and optical devices due to its piezoelectric, dielectric and optical features [206].”
Room-Temperature Polariton Lasing in an Organic Single-Crystal Microcavity
Kéna-Cohen, S., & Forrest, S. R. (2010) · Nature Photonics · doi:10.1038/nphoton.2010.86 · Cited by 942
Room-Temperature Bose–Einstein Condensation of Cavity Exciton–Polaritons in a Polymer
Plumhof, J. D., Stöferle, T., Mai, L., Scherf, U., & Mahrt, R. F. (2014) · Nature Materials · doi:10.1038/nmat3825 · Cited by 745 · cited 1×
“The possibilities of achieving Bose–Einstein condensation (BEC) [264–267] and polariton lasing [137,268–270], even at room temperature, are some of the current topics in the field of microcavity research.”
Lithium niobate photonics: Unlocking the electromagnetic spectrum
Boes, A., Chang, L., Langrock, C., Yu, M., Zhang, M., Lin, Q., Lončar, M., Fejer, M., Bowers, J., & Mitchell, A. (2023) · Science · doi:10.1126/science.abj4396 · Cited by 666
Large Pockels effect in micro- and nanostructured barium titanate integrated on silicon
Abel, S., Eltes, F., Ortmann, J. E., Messner, A., Castera, P., Wagner, T., Urbonas, D., Rosa, A., Gutierrez, A. M., Tulli, D., et al. (2019) · Nature Materials · doi:10.1038/s41563-018-0208-0 · Cited by 554
Polariton-Mediated Energy Transfer between Organic Dyes in a Strongly Coupled Optical Microcavity
Coles, D. M., Somaschi, N., Michetti, P., Clark, C., Lagoudakis, P. G., Savvidis, P. G., & Lidzey, D. G. (2014) · Nature Materials · doi:10.1038/nmat3950 · Cited by 507 · cited 1×
“…light scattering and maintains the specu-https lar component of the reflection; in contrast, a rougher surface introduces significant diffuse scattering, diminishing the effective reflectance, especially when the roughness becomes comparable to a relevant fraction of the wavelength [242,243].”
Cited by
Arda, L., Özuğurlu, E., & Taşçıoğlu, İ. (2026) · Crystals · doi:10.3390/cryst16050291 · Cited by 2
Metadata
- Authors
- Stîngescu, M.-L., Șopronyi, M.-A., Antohe, Ș., & Scărișoreanu, N.-D.
- Affiliations
- University of Bucharest (RO)
- National Institute for Laser, Plasma and Radiation Physics (INFLPR), Atomiștilor Street 409, 077125 Măgurele, Romania
- R&D Center for Materials and Electronic & Optoelectronic Devices (MDEO), Faculty of Physics, University of Bucharest, Atomiștilor Street 405, 077125 Măgurele, Romania
- Venue
- Crystals
- Publisher
- MDPI AG
- Published
- 2026-02-27
- Volume
- 16
- Issue
- 3
- Pages
- 164
- ISSN
- 2073-4352 (ISSN-L)
- OpenAlex
- W7131786704
- Cited by
- 2
- References
- 295
- Citations by year
- 2026: 2
- FWCI
- 2.74
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Crystals (publishedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Funders
- Ministerul Cercetării și Inovării (Cod SMIS 351364, Contract nr. G 2024-85828/390008/27.11.2024, Program LAPLAS VII – contract no. 30N/2023.)
- Topics
- Physical Sciences › Materials Science › Surfaces, Coatings and Films › Optical Coatings and Gratings
- Physical Sciences › Physics and Astronomy › Atomic and Molecular Physics, and Optics › Photorefractive and Nonlinear Optics
- Physical Sciences › Materials Science › Materials Chemistry › Electronic and Structural Properties of Oxides
- Keywords
- metal oxide thin films, dielectric mirrors, distributed Bragg reflector, planar microcavities, light confinement, quality factor, passive optical components, complex oxides, lithium niobate, lithium tantalate, barium titanate, epitaxial growth, monolithic integration
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-08, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-08 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Metal Oxide Thin Films for Advanced Photonic Applications. https://app.cochat.ai/papers/10.3390/cryst16030164
- The paper
- Stîngescu, M.-L., Șopronyi, M.-A., Antohe, Ș., & Scărișoreanu, N.-D. (2026). Metal Oxide Thin Films for Advanced Photonic Applications. Crystals. https://doi.org/10.3390/cryst16030164
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.