The DOI matches its Crossref record; 41 of the 41 references it cites were found in a registry or an index.
A Comparative Study of Power Supply Architectures in Wireless EV Charging Systems
Abstract
This paper examines two of the primary power supply architectures being predominantly used for wireless electric vehicle (EV) charging, namely the series LC (SLC) resonant and the hybrid series-parallel (LCL) resonant full-bridge inverter topologies. The study of both of these topologies is presented in the context of designing a 3-kW primary-side controlled stationary wireless EV charger with nominal operating parameters of 30-kHz center frequency, a range of coupling in the neighborhood of 0.18-0.26, and a parallel secondary pick-up with partial series coil compensation. A comparison of both architectures is made in terms of their design methodology, physical size, cost, complexity, and efficiency. It is found that the SLC architecture is 2.45% less costly than the LCL topology. On the other hand, it is observed that the LCL architecture achieves almost 10% higher peak efficiency at rated load and minimum coupling. The study also showed that the SLC topology suffers from poor light load efficiency, while the LCL topology maintains very high efficiency over its full range of coupling and loading. The study also revealed that the capacitor voltage stress is significantly higher in the SLC topology. Finally, it is also shown that the control complexity of the SLC architecture is higher than that of the LCL architecture because of its sensitivity to changes in the reflected secondary impedance, which result in loss of constant current source and ZVS operation unless a suitable combination of parameters are modulated by the closed-loop controller.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
A comparison of half-bridge resonant converter topologies
Steigerwald, R. L. (1988) · IEEE Transactions on Power Electronics · doi:10.1109/63.4347 · Cited by 1,972
Sample, A. P., Meyer, D. A., & Smith, J. R. (2011) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2010.2046002 · Cited by 1,808
Design Considerations for a Contactless Electric Vehicle Battery Charger
Wang, C.-S., Stielau, O. H., & Covic, G. A. (2005) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2005.855672 · Cited by 1,487
Development of a Single-Sided Flux Magnetic Coupler for Electric Vehicle IPT Charging Systems
Budhia, M., Boys, J. T., Covic, G. A., & Huang, C.-Y. (2013) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2011.2179274 · Cited by 1,273
Modern Trends in Inductive Power Transfer for Transportation Applications
Covic, G. A., & Boys, J. T. (2013) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2013.2264473 · Cited by 1,263
Covic, G. A., & Boys, J. T. (2013) · Proceedings of the IEEE · doi:10.1109/jproc.2013.2244536 · Cited by 1,223
Wang, C.-S., Covic, G. A., & Stielau, O. H. (2004) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2003.822038 · Cited by 1,213
Design and Optimization of Circular Magnetic Structures for Lumped Inductive Power Transfer Systems
Budhia, M., Covic, G. A., & Boys, J. T. (2011) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2011.2143730 · Cited by 1,039
Optimal Design of ICPT Systems Applied to Electric Vehicle Battery Charge
Sallan, J., Villa, J. L., Llombart, A., & Sanz, J. F. (2009) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2009.2015359 · Cited by 734
Narrow-Width Inductive Power Transfer System for Online Electrical Vehicles
Huh, J., Lee, S. W., Lee, W. Y., Cho, G. H., & Rim, C. T. (2011) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2011.2160972 · Cited by 669
Stability and control of inductivelycoupled power transfer systems
Boys, J. T., Covic, G. A., & Green, A. W. (2000) · IEE Proceedings - Electric Power Applications · doi:10.1049/ip-epa:20000017 · Cited by 559
Simple Inductance Formulas for Radio Coils
Wheeler, H. A. (1928) · Proceedings of the IRE · doi:10.1109/jrproc.1928.221309 · Cited by 548
Primary-Side Power Flow Control of Wireless Power Transfer for Electric Vehicle Charging
Miller, J. M., Onar, O. C., & Chinthavali, M. (2015) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2014.2382569 · Cited by 533
A High Efficiency 5 kW Inductive Charger for EVs Using Dual Side Control
Wu, H. H., Gilchrist, A., Sealy, K. D., & Bronson, D. (2012) · IEEE Transactions on Industrial Informatics · doi:10.1109/tii.2012.2192283 · Cited by 512
Hui, S. Y. R., & Ho, W. W. C. (2005) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2005.846550 · Cited by 501
Cutting the Cord: Static and Dynamic Inductive Wireless Charging of Electric Vehicles
Lukic, S., & Pantic, Z. (2013) · IEEE Electrification Magazine · doi:10.1109/mele.2013.2273228 · Cited by 424
Bosshard, R., Kolar, J. W., Muhlethaler, J., Stevanovic, I., Wunsch, B., & Canales, F. (2015) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2014.2311302 · Cited by 411
A Unity-Power-Factor IPT Pickup for High-Power Applications
Keeling, N. A., Covic, G. A., & Boys, J. T. (2010) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2009.2027255 · Cited by 371
Design of a contactless battery charger for cellular phone
Kim, C.-G., Seo, D.-H., You, J.-S., Park, J.-H., & Cho, B. H. (2001) · IEEE Transactions on Industrial Electronics · doi:10.1109/41.969404 · Cited by 345
Design of loosely coupled inductive power transfer systems
Stielau, O. H., & Covic, G. A. (2002) · PowerCon 2000. 2000 International Conference on Power System Technology. Proceedings (Cat. No.00EX409) · doi:10.1109/icpst.2000.900036 · Cited by 328
ZCS $LCC$-Compensated Resonant Inverter for Inductive-Power-Transfer Application
Pantic, Z., Bai, S., & Lukic, S. M. (2011) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2010.2081954 · Cited by 305
10 kHz inductively coupled power transfer - concept and control
Green, A. W. (1994) · Proceedings of 5th International Conference on Power Electronics and Variable-Speed Drives · doi:10.1049/cp:19941049 · Cited by 300
On-Line Electric Vehicle using inductive power transfer system
Lee, S., Huh, J., Park, C., Choi, N.-S., Cho, G.-H., & Rim, C.-T. (2010) · 2010 IEEE Energy Conversion Congress and Exposition · doi:10.1109/ecce.2010.5618092 · Cited by 277
Analysis and Design of an LCL-T Resonant Converter as a Constant-Current Power Supply
Borage, M., Tiwari, S., & Kotaiah, S. (2005) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2005.858729 · Cited by 271
A new IPT magnetic coupler for electric vehicle charging systems
Budhia, M., Covic, G., & Boys, J. (2010) · IECON 2010 - 36th Annual Conference on IEEE Industrial Electronics Society · doi:10.1109/iecon.2010.5675350 · Cited by 268
Miller, J. M., Onar, O. C., White, C., Campbell, S., Coomer, C., Seiber, L., Sepe, R., & Steyerl, A. (2014) · IEEE Power Electronics Magazine · doi:10.1109/mpel.2014.2300978 · Cited by 256
A novel wireless power transfer for in-motion EV/PHEV charging
Onar, O. C., Miller, J. M., Campbell, S. L., Coomer, C., White, C. P., & Seiber, L. E. (2013) · 2013 Twenty-Eighth Annual IEEE Applied Power Electronics Conference and Exposition (APEC) · doi:10.1109/apec.2013.6520738 · Cited by 244
Investigating an LCL Load Resonant Inverter for Inductive Power Transfer Applications
Wang, C.-S., Covic, G. A., & Stielau, O. H. (2004) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2004.830098 · Cited by 242
Multiphase Pickups for Large Lateral Tolerance Contactless Power-Transfer Systems
Elliott, G., Raabe, S., Covic, G. A., & Boys, J. T. (2010) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2009.2031184 · Cited by 234
Hao, H., Covic, G. A., & Boys, J. T. (2014) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2013.2293138 · Cited by 209
New Cross-Segmented Power Supply Rails for Roadway-Powered Electric Vehicles
Choi, S., Huh, J., Lee, W. Y., Lee, S. W., & Rim, C. T. (2013) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2013.2247634 · Cited by 196
A bipolar receiver pad in a lumped IPT system for electric vehicle charging applications
Zaheer, A., Kacprzak, D., & Covic, G. A. (2012) · 2012 IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce.2012.6342811 · Cited by 178
Interphase Mutual Inductance in Polyphase Inductive Power Transfer Systems
Kissin, M. L. G., Boys, J. T., & Covic, G. A. (2009) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2009.2020076 · Cited by 165
The design of a contact-less energy transfer system for a people mover system
Covic, G. A., Elliott, G., Stielau, O. H., Green, R. M., & Boys, J. T. (2002) · PowerCon 2000. 2000 International Conference on Power System Technology. Proceedings (Cat. No.00EX409) · doi:10.1109/icpst.2000.900035 · Cited by 165
Innovative 5-m-Off-Distance Inductive Power Transfer Systems With Optimally Shaped Dipole Coils
Park, C., Lee, S., Cho, G., & Rim, C. T. (2014) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2014.2310232 · Cited by 150
Load models and their application in the design of loosely coupled inductive power transfer systems
Wang, C.-S., Stielau, O. H., & Covic, G. A. (2002) · International Conference on Power System Technology (POWERCON) · doi:10.1109/icpst.2000.897166 · Cited by 115
Chigira, M., Nagatsuka, Y., Kaneko, Y., Abe, S., Yasuda, T., & Suzuki, A. K. (2011) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce.2011.6063778 · Cited by 113
Grid side regulation of wireless power charging of plug-in electric vehicles
Miller, J. M., White, C. P., Onar, O. C., & Ryan, P. M. (2012) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce.2012.6342814 · Cited by 94
Practical considerations for designing IPT system for EV battery charging
Huang, C.-Y., Boys, J. T., Covic, G. A., & Budhia, M. (2009) · IEEE Vehicle Power and Propulsion Conference (VPPC) · doi:10.1109/vppc.2009.5289821 · Cited by 90
High frequency resonant inverter for contactless energy transmission over large air gap
Mecke, R., & Rathge, C. (2004) · IEEE Power Electronics Specialists Conference (PESC) · doi:10.1109/pesc.2004.1355378 · Cited by 85
Musavi, F., Edington, M., Eberle, W., & Dunford, W. G. (2011) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce.2011.6063780 · Cited by 63
Cited by
A Comprehensive Review of Wireless Charging Technologies for Electric Vehicles
Ahmad, A., Alam, M. S., & Chabaan, R. (2018) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2017.2771619 · Cited by 993
Inductive Wireless Power Transfer Charging for Electric Vehicles—A Review
Mahesh, A., Chokkalingam, B., & Mihet-Popa, L. (2021) · IEEE Access · doi:10.1109/access.2021.3116678 · Cited by 513
Khalid, M. R., Alam, M. S., Sarwar, A., & Jamil Asghar, M. S. (2019) · eTransportation · doi:10.1016/j.etran.2019.100006 · Cited by 369
Advances in High-Power Wireless Charging Systems: Overview and Design Considerations
Feng, H., Tavakoli, R., Onar, O. C., & Pantic, Z. (2020) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2020.3012543 · Cited by 368
Khalid, M. R., Khan, I. A., Hameed, S., Asghar, M. S. J., & Ro, J. (2021) · IEEE Access · doi:10.1109/access.2021.3112189 · Cited by 353
Metadata
- Authors
- Esteban, B., Sid-Ahmed, M., & Kar, N. C.
- Venue
- IEEE Transactions on Power Electronics
- Published
- 2015-11
- Volume
- 30
- Issue
- 11
- Pages
- 6408-6422
- ISSN
- 0885-8993 (ISSN-L)
- 1941-0107
- OpenAlex
- W1517714277
- Cited by
- 256
- References
- 41
- FWCI
- 12.19
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.