AC Power Cycling Test Setup and Condition Monitoring Tools for SiC-Based Traction Inverters
Open accessThe DOI matches its Crossref record; 95 of the 97 references it cites were found in a registry or an index; 7 of the 74 sources its claims cite were checked for support.
Abstract
AC power cycling tests allow the most realistic reliability assessment by applying close to real stress to the device or module under test to meet functional safety standards, which is highly critical for traction applications. This article presents a comprehensive guideline and shares critical know-how to develop a 120 KVA AC power cycling test setup for high-power Silicon Carbide (SiC) modules. As of today, traction applications can not generate an early warning signal for drivers to replace critical components on time. For this purpose, the suitable precursors for all dominant failure mechanisms are discussed, and the corresponding condition monitoring tools are proposed to monitor the device aging on power converters. These condition monitoring tools are integrated into the built-in desaturation protection circuit of the electric vehicle (EV) gate driver for low-cost, practical implementation. The on-resistance of all twelve switches is monitored online as a temperature-sensitive electrical parameter (TSEP) to measure the junction temperature of the devices. To avoid heavy processing load in the microcontroller, the out-of-order equivalent time sampling technique is developed for data sampling, which leads to a measurement error of less than 1.5%. In addition, the design considerations regarding common mode noise and aging effect on DESAT protection are investigated, and experimental findings are presented.
Overview
CoChat Summary
TL;DR
The paper presents a 120 KVA AC power cycling test setup for high-power SiC traction inverter modules and integrates condition monitoring into the DESAT gate-driver protection circuit. It selects on-resistance, body diode voltage, and threshold voltage as aging precursors, uses on-resistance as a TSEP for junction temperature, and reports less than 1.5% error for filtered online on-resistance measurement.
Key findings
- A 120 KVA AC power cycling setup was developed using two back-to-back three-phase inverters, with SiC modules as the inverter under test and IGBT modules as the electrical load; it supports up to 400 A and programmable modulation index, switching frequency, fundamental frequency, DC-link voltage, current amplitude, and power factor.
- On-resistance, body diode voltage, and threshold voltage were selected to monitor package, body diode, and gate-oxide degradation, with their condition monitoring circuits integrated into the DESAT protection circuit to reduce component count.
- Online on-resistance was used as the TSEP for junction temperature; the out-of-order equivalent time sampling technique captures 300 data points around peak values, and after FIR filtering the online on-resistance measurement error is less than 1.5% compared with Keysight 1506A curve tracer results.
- Threshold voltage measurement error was less than 0.1 V compared with the curve tracer, and oxide aging increased drain-to-source voltage from 1.58 V to 2.6 V at nominal current with Vgs = 15 V, which can cause false DESAT triggers unless threshold-voltage shift is used to adjust the DESAT threshold.
Methods
- Design and experimental validation of a 120 KVA AC power cycling test setup with two three-phase back-to-back inverters, separate active liquid cooling, laminated busbars, three 700 µH/400 A inductors, UCC5870 gate drivers, and an F28388D C2000 MCU.
- Condition monitoring circuits were developed for on-resistance/body-diode voltage and threshold voltage, integrated into the DESAT protection circuit; TSEPs were compared, and on-resistance was selected for online junction temperature measurement.
- Main analysis included precursor comparison, TSEP table evaluation, experimental waveforms in motor mode (PF = 1) and generator mode (PF = -1), thermal cycling, aging experiments, and error comparison against a Keysight 1506A curve tracer.
Limitations
- Stated in the paper: the constant case-temperature-swing technique using an NTC sensor may introduce measurement inaccuracies; DESAT is susceptible to noise in high-voltage applications; on-resistance is nonlinear with temperature and dependent on package and gate-oxide degradation, requiring periodic recalibration/compensation; body diode voltage at high currents is affected by package degradation; online threshold voltage measurement requires fast sampling.
- Evident from the text: validation is limited to a laboratory AC power cycling setup and specific SiC modules/vendors, with no field deployment or long-term lifetime extrapolation reported.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
6 Valid · 16 Not valid · 44 Not checked · 111 Own results and interpretations
At least one cited source doesn’t support this claim or points to a different paper, and none confirmed it — see the verdicts below.
In the paper
“The chopper mode bias (CMB) test accelerates the internal PiN diode degradation by body diode conduction [62], [63].”
What the sources say
- Disputedcites [62] sourceExperimental — accuracy not yet measured
Section 3.3 describes CMB testing that forces current through the intrinsic diode to assess possible P–N junction degradation. But section 4.2 reports that the diode’s forward voltage remained constant, suggesting no noticeable P–N junction degradation; the observed degradation was in threshold voltage instead. (LLM, conf=0.89)
Checked by a reasoning model — may be wrong.
- Not checked — no full text of the sourcecites [63] source
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Disputed
Every source the paper cites for this claim was checked and supports it.
In the paper
“However, the on-resistance relation with junction temperature is not perfectly linear in SiC MOSFETs.”
What the sources say
- Supportedcites [98] source
The Results and discussion (Figure 7) report that on-resistance first decreases as temperature rises from 300 K to 370 K, then increases at higher temperatures. That change in direction supports a non-linear temperature relationship for the 4H-SiC VDMOSFETs studied. (LLM, conf=0.92)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“On the other hand, drift region mobility decreases as the temperature increases.”
What the sources say
- Partly supportedcites [99] sourceExperimental — accuracy not yet measured
In III. STATIC CHARACTERIZATION (page not available), the paper says drift-region resistance increases as temperature rises. That is consistent with the claimed decrease in mobility, but our copy does not state or measure drift-region mobility directly. (LLM, conf=0.79)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
Every source the paper cites for this claim was checked and supports it.
In the paper
“Therefore, drift region resistance increases at elevated temperatures [99].”
What the sources say
- Supportedcites [99] source
The paper’s III. STATIC CHARACTERIZATION section explicitly states that drift region resistance increases as temperature rises, in its discussion of the SiC trench MOSFETs’ temperature-dependent on-resistance. The claim preserves that point. (LLM, conf=0.94)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“To avoid heavy processing load in the microcontroller, the out-of-order equivalent time sampling technique is developed for data sampling, which leads to a measurement error of less than 1.5 % .”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
72 more claims
Create a free account to see all 177 claims and every source verdict.
- Probably not a substantial claim. 67
- It may state two separate claims as one. 51
- The quote only partly states this claim. 1
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ B. Threshold Voltage Measurement · p. 8
“The aging impact on the threshold voltage at the channel current of 2 mV is depicted in Fig. 14.”
§ B. Threshold Voltage Measurement · p. 8
“In this setup, the threshold voltage is monitored at IDESAT = 2 mA .”
Citations
Cites
An Industry-Based Survey of Reliability in Power Electronic Converters
Yang, S., Bryant, A., Mawby, P., Xiang, D., Ran, L., & Tavner, P. (2011) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2011.2124436 · Cited by 2,019
Selected failure mechanisms of modern power modules
Ciappa, M. (2002) · Microelectronics Reliability · doi:10.1016/s0026-2714(02)00042-2 · Cited by 1,039 · cited 1×
“Also, SiC has lower CTE compared to Al surface (4.3 ppm/ ◦ C vs. 22 ppm/ ◦ C) which translates to plastic deformation at high junction temperatures [47], [48].”
BackgroundInfluentialAgeing and Failure Modes of IGBT Modules in High-Temperature Power Cycling
Smet, V., Forest, F., Huselstein, J.-J., Richardeau, F., Khatir, Z., Lefebvre, S., & Berkani, M. (2011) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2011.2114313 · Cited by 620 · cited 2×
“[35], [38], [39], [40].”
Background(2008) · Cited by 578
Degradation of hexagonal silicon-carbide-based bipolar devices
Skowronski, M., & Ha, S. (2006) · Journal of Applied Physics · doi:10.1063/1.2159578 · Cited by 474
Reliability and performance limitations in SiC power devices
Singh, R. (2006) · Microelectronics Reliability · doi:10.1016/j.microrel.2005.10.013 · Cited by 284
Threshold voltage peculiarities and bias temperature instabilities of SiC MOSFETs
Aichinger, T., Rescher, G., & Pobegen, G. (2018) · Microelectronics Reliability · doi:10.1016/j.microrel.2017.11.020 · Cited by 278
Bulk and epitaxial growth of silicon carbide
Kimoto, T. (2016) · Progress in Crystal Growth and Characterization of Materials · doi:10.1016/j.pcrysgrow.2016.04.018 · Cited by 222 · cited 1×
“Fromthechippointofview,someoftheissues related to the extrinsic defects, Basal plane dislocations, and stacking fault (SF) have been addressed over recent years [14], [15].”
BackgroundAn introduction to Cu electromigration
Hau-Riege, C. S. (2004) · Microelectronics Reliability · doi:10.1016/j.microrel.2003.10.020 · Cited by 221 · cited 1×
“In addition to the thermal cycle, a high drain-current can accelerate bond-wire aging by expanding the internal void in Al bond-wires [43], [44].”
BackgroundReview and analysis of SiC MOSFETs’ ruggedness and reliability
Wang, J., & Jiang, X. (2020) · IET Power Electronics · doi:10.1049/iet-pel.2019.0587 · Cited by 221
Research works printed but not linked: 2
- Suganuma, 2018, Wide Bandgap Power Semiconductor Packaging: Materials, Components, and Reliability
- 2010, Temperature, Bias, and Operating Life
Cited by
Hosseinabadi, F., Chakraborty, S., Bhoi, S. K., Prochart, G., Hrvanovic, D., & Hegazy, O. (2024) · IEEE Open Journal of Power Electronics · doi:10.1109/ojpel.2024.3379294 · Cited by 138
“Conducting accelerated aging tests is essential for gathering data to prepare both data-driven models and physics-based models, as well as for conducting advanced failure mechanism analyses during the design stage [14], [15].”
MethodAbbaszada, M. A., Gajanur, N., & Mazumder, S. K. (2025) · Microelectronics Reliability · doi:10.1016/j.microrel.2025.115589 · Cited by 18
Offline Fault Diagnosis for 2-Level Inverter: Short-Circuit and Open-Circuit Detection
Hyon, B. J., Hwang, D. Y., Jang, P., Noh, Y.-S., & Kim, J.-H. (2024) · Electronics · doi:10.3390/electronics13091672 · Cited by 8
Statistical Analysis of Power Semiconductor Devices Lifetime Test and Lifetime Prediction
Zhou, X., Xin, Z., Wu, Z., & Sheng, K. (2024) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2024.3495993 · Cited by 11
“KG [5], [6], [7], [8], [9], [10], [11] has been committed to separating solder fatigue and bonding wire fatigue.”
InfluentialReview on the Thermal Parameters Applications in the Reliability of Power Semiconductor Device
Shen, H., Zhang, J., Sun, P., & Ma, X. (2024) · IEEE International Electrical and Energy Conference (CIEEC) · doi:10.1109/cieec60922.2024.10583571 · Cited by 6
Metadata
- Authors
- Farhadi, M., Vankayalapati, B. T., Sajadi, R., & Akin, B.
- Affiliations
- The University of Texas at Dallas (US)
- Texas Instruments (United States) (US)
- Venue
- IEEE Transactions on Vehicular Technology
- Published
- 2023-10
- Volume
- 72
- Issue
- 10
- Pages
- 12728-12743
- ISSN
- 0018-9545 (ISSN-L)
- 1939-9359
- OpenAlex
- W4367663380
- Cited by
- 24
- References
- 97
- Citations by year
- 2026: 6 · 2025: 4 · 2024: 13 · 2023: 1
- FWCI
- 1.79
- Type
- journal article
- Language
- en
- Open access
- green
- arxiv.org
- Licence
- Locations
- IEEE Transactions on Vehicular Technology (publishedVersion)
- arXiv (Cornell University) (submittedVersion, public-domain)
- arXiv (Cornell University) (public-domain)
- Funders
- Texas Instrument Automotive Group and Semiconductor Research Corporation/Texas Analog Center of Excellence (2810.054)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Silicon Carbide Semiconductor Technologies
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Multilevel Inverters and Converters
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Electric Power Systems and Control
- Keywords
- traction inverter, condition monitoring, device aging, failure mechanisms, temperature-sensitive electrical parameters, junction temperature, equivalent time sampling, common-mode noise, reliability analysis
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: AC Power Cycling Test Setup and Condition Monitoring Tools for SiC-Based Traction Inverters. https://app.cochat.ai/papers/10.1109/tvt.2023.3271251
- The paper
- Farhadi, M., Vankayalapati, B. T., Sajadi, R., & Akin, B. (2023). AC Power Cycling Test Setup and Condition Monitoring Tools for SiC-Based Traction Inverters. IEEE Transactions on Vehicular Technology. https://doi.org/10.1109/tvt.2023.3271251
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.