Biodegradable synthetic polymers for tissue engineering
Open accessThe DOI matches its Crossref record; 96 of the 97 references it cites were found in a registry or an index; 1 of the 146 sources its claims cite were checked for support.
Abstract
This review focuses on biodegradable synthetic polymers, discussing synthesis, properties and biodegradability, especially within the polyester family including polylactides.
Overview
CoChat Summary
TL;DR
This review surveys biodegradable synthetic polymers for tissue engineering, emphasizing polyesters (PGA, PLA, PLGA), polylactones, poly(propylene fumarate), polyanhydrides, tyrosine-derived polycarbonates, polyorthoesters, polyurethanes, and polyphosphazenes. It concludes that polyesters dominate clinically, while injectable in situ curable systems such as PPF and photocrosslinkable polyanhydrides are promising but face challenges in biocompatibility, degradation control, and heat generation.
Key findings
- Polyesters are the most studied biodegradable polymers. PGA has 46–50% crystallinity, Tg 36°C, Tm 225°C; in Dexon sutures in vitro, first-stage degradation predominates for 21 days, crystalline degradation takes a further 28 days, and after 49 days weight loss was about 42% with complete loss of mechanical properties.
- PLA/PGA copolymer behavior depends on composition: 25–75% (l)LA/GA and 0–70% (dl)LA/GA are amorphous; 70/30 GA/LA has the highest water uptake, while 50/50 is reported as most unstable to hydrolysis; Vicryl is 8% (l)LA and 92% GA.
- Poly(caprolactone) degrades slowly: homopolymer degradation is on the order of 2–3 years, and PCL with initial average molecular weight 50,000 takes about 3 years for complete in vitro degradation.
- Poly(propylene fumarate) degrades to fumaric acid and propylene glycol; time to 20% original weight loss ranged from 84 days (PPF/β-TCP composite) to over 200 days (PPF/CaSO4 composite). PPF formulations showed maximum curing temperatures of 38–48°C versus 94°C for PMMA cements, curing times of 1–121 min, and compressive strengths of 1–12 MPa.
- Polyanhydrides degrade by surface erosion; poly(sebacic acid) degrades in about 54 days in saline, while poly(1,6-bis(p-carboxyphenoxy)hexane) is estimated at 1 year. Poly[1,6-bis(carboxyphenoxy)hexane] has a Young’s modulus of 1.3 MPa versus human bone at 40–60 MPa; poly(anhydride-co-imides) reached compressive strengths of 50–60 MPa, and photocrosslinked systems showed compressive strengths of 30–40 MPa and tensile strengths of 15–27 MPa.
- Degradable polyurethanes based on lysine diisocyanate showed varied properties: dl-lactide networks were rigid (Tg = 60°C) with ultimate tensile strengths of ~40–70 MPa, caprolactone triol networks were low-modulus elastomers with tensile strengths of 1–4 MPa, and copolymer networks had elongation up to 600% with compressive strengths of 3–25 MPa. In vivo, porous polyurethane artificial skin degraded almost completely 4–8 weeks after implantation in guinea pigs with no adverse tissue reaction.
Methods
- Design: narrative literature review; no primary experimental study or systematic review protocol is reported.
- Data/sample: published literature on biodegradable synthetic polymers, including synthesis, properties, degradation, biocompatibility, and injectable polymer systems; Tables 1–3 summarize polymer properties and precursors.
- Analysis: qualitative synthesis of major polymer classes, their degradation modes/products, mechanical properties, biocompatibility, and potential for injectable tissue-engineering compositions.
Limitations
- Stated: the paper notes that Table 2 data “should be used as a guide only” and that sufficient data are not available to provide a comprehensive list of properties for polyanhydrides, polycarbonates, polyurethanes, and polyphosphazenes.
- Stated: for polyanhydrides, no data are reported about polymer sterilizability and heat generation during polymerization; for degradable polyurethanes, the effect of degradation products and how they are removed from the body are not clearly understood.
- Evident: as a narrative review, it lacks systematic search criteria, study quality appraisal, and meta-analysis, so conclusions depend on the cited literature and may not comprehensively cover all biodegradable polymers or tissue-engineering applications.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
1 Valid · 20 Not valid · 105 Not checked · 89 Own results and interpretations
Every source the paper cites for this claim was checked and supports it.
In the paper
“A meniscal replica implanted contained only fibro-cartilage after 18 weeks and decreased the degradation of the articular cartilage.”
What the sources say
- Supportedcites De Groot et al.., 1996 source
The Aliphatic PU network passage (page not provided) reports that articular-cartilage degeneration was less severe with the prosthesis than in meniscectomized control knees. It also says the prostheses contained only fibrocartilage after 18 weeks. Degeneration was reduced, not eliminated. (LLM, conf=0.91)
plainstates a causeSingle case- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
In the paper
“The compressive strengths varied between 1 and 12 MPa”
What the sources say
- Not matchedcites Peter et al., 1998a
Couldn’t be matched to a paper in Crossref, so it can’t be checked.
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Not matched
In the paper
“Cross-linking characteristics reported for PPF, N-vinyl pyrrolidone (N-VP), benzoyl peroxide, sodium chloride, and TCP indicate that for a range of formulations, the maximum temperature varied within 38 to about 48ºC, compared to 94ºC observed for polymethylmethacrylate (PMMA) cements.”
What the sources say
- Not matchedcites Peter et al., 1998a
Couldn’t be matched to a paper in Crossref, so it can’t be checked.
hedged- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Not matched
None of the sources cited for this claim could be matched to a paper in Crossref, so there is nothing to check it against.
In the paper
“Based on in-vitro studies, the time required to reach 20% loss in original weight ranged from 84 (PPF/ß-TCP composite) to over 200 days (PPF/CaSO 4 composite)”
What the sources say
- Not matchedcites Peter et al., 1997b
Couldn’t be matched to a paper in Crossref, so it can’t be checked.
- Not matchedcites Kharas et al., 1997
Couldn’t be matched to a paper in Crossref, so it can’t be checked.
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Not matched
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“These composite materials exhibit compressive strengths in the range 2 to 30 MPa.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
94 more claims
Create a free account to see all 215 claims and to verify the 2 references still open.
- It may state two separate claims as one. 62
- Probably not a substantial claim. 76
- The quote only partly states this claim. 1
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“Advantages include a tightly controlled manufacturing process, accurate reproducibility, adjustable biodegradability, and a wide variety of both chemical and physical properties.[ 171 ]”
From Unraveling and Harnessing the Immune Response at the Cell–Biomaterial Interface for Tissue Engineering Purposes (2024) · cites this paper as [171]
Experimental — accuracy not yet measured
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
§ Polyanhydrides
“Polyanhydrides degrades by surface erosion (Kohn and Langer, 1997) and their main applications are in controlled drug delivery.”
§ Conclusions
“Polyanhydride degrade by bulk erosion and their main applications are in controlled drug delivery.”
Citations
Cites
Synthetic biodegradable polymers as orthopedic devices
Middleton, J. C., & Tipton, A. J. (2000) · Biomaterials · doi:10.1016/s0142-9612(00)00101-0 · Cited by 2,741 · cited 4×
“…developments in siloxane-based polyurethanes, which have greater in-vivo stability than conventional polyetherurethanes (e.g., poly(tetramethylene oxide) (PTMO)-based) have provided opportunities for development of a range of medical implants for chronic applications (Gunatillake et al., 2001).”
BackgroundInfluentialBiomaterial developments for bone tissue engineering
Burg, K. J. L., Porter, S., & Kellam, J. F. (2000) · Biomaterials · doi:10.1016/s0142-9612(00)00102-2 · Cited by 1,643 · cited 1×
“Polyesters have also been considered for development of tissue engineering applications (Hubbell, 1995; Thomson et al 1995a, Yazemski et al. 1996; Wong and Mooney, 1997), particularly for bone tissue engineering (Kohn and Langer, 1997; Burg et al., 2000).”
BackgroundChandra, R. (1998) · Progress in Polymer Science · doi:10.1016/s0079-6700(97)00039-7 · Cited by 1,462
Biodegradable polymers for use in surgery—polyglycolic/poly(actic acid) homo- and copolymers: 1
Gilding, D. K., & Reed, A. M. (1979) · Polymer · doi:10.1016/0032-3861(79)90009-0 · Cited by 1,345
Biomaterials in Tissue Engineering
Hubbell, J. A. (1995) · Nature Biotechnology · doi:10.1038/nbt0695-565 · Cited by 1,060 · cited 1×
“Polyesters have also been considered for development of tissue engineering applications (Hubbell, 1995; Thomson et al 1995a, Yazemski et al. 1996; Wong and Mooney, 1997), particularly for bone tissue engineering (Kohn and Langer, 1997; Burg et al., 2000).”
BackgroundPolylactic Acid for Surgical Implants
KULKARNI, R. K. (1966) · Archives of Surgery · doi:10.1001/archsurg.1966.01330050143023 · Cited by 841
Evolution of bone transplantation: molecular, cellular and tissue strategies to engineer human bone
Yaszemski, M. J., Payne, R. G., Hayes, W. C., Langer, R., & Mikos, A. G. (1996) · Biomaterials · doi:10.1016/0142-9612(96)85762-0 · Cited by 729
Miller, R. A., Brady, J. M., & Cutright, D. E. (1977) · Journal of Biomedical Materials Research · doi:10.1002/jbm.820110507 · Cited by 722 · cited 2×
“For the (l)LA/GA copolymers, resistance to hydrolysis is more pronounced at either end of the copolymers compositions range (Miller et al., 1977; Gilding and Reed, 1979; Reed and Gilding, 1981; Vert et al., 1984).”
BackgroundInjectable biodegradable materials for orthopedic tissue engineering
Temenoff, J. S., & Mikos, A. G. (2000) · Biomaterials · doi:10.1016/s0142-9612(00)00108-3 · Cited by 554 · cited 8×
“A number of methods have been reported to prepare PPF, and each results in different polymer properties (Peter et al., 1997a,b, 1999; Temenoff and Mikos 2000).”
BackgroundMethodInfluentialLeong, K. W., Brott, B. C., & Langer, R. (1985) · Journal of Biomedical Materials Research · doi:10.1002/jbm.820190806 · Cited by 541 · cited 12×
“The polyurethanes ranged from elastomers with elongations at break as high as 780 %, but with low tensile strengths (5.8 to 8.1 MPa).”
BackgroundInfluential
Research works printed but not linked: 5
- Scranton A, Bowman C, Peiffer R, eds. ACS Symposium Series 673; American Chemical Society, Washington DC. pp 189-202.
- Ratner BD, Hoffman AS, Schoen FJ, Lemon JE, eds. Aca- demic Press, San Diego. pp 65-73.
- Lamba NMK, Woodhouse KA, Cooper SL (1998) Poly- urethanes in Biomedical Applications. CRC Press: New York p 205-241.
- Mark JE, Alcock HR, West R (1992) Inorganic Poly- mers. Prentice Hall, Upper Saddle River, NJ. Chapter
- Ng SY, Vandamme T, Tayler MS, Heller J (1997) Syn- thesis and erosion studies of self-catalysed poly(orthoester)s. Macromolecules 30: 770-772.
Cited by
Items 1,401–1,500 of 1,762
Biomaterials for Hard Tissue Engineering: Concepts, Methods, and Applications
Saraswathy, M., Krishnaswami, V., & Ragini, D. D. (2021) · Springer eBooks · doi:10.1007/978-981-16-0002-9_10 · Cited by 4
Woo, R. K., Jenkins, D., & Greco, R. S. (2004) · CRC Press eBooks · doi:10.1201/9780203500224.ch1 · Cited by 2
Depan, D. (2015) · CRC Press eBooks · doi:10.1201/b19314-10 · Cited by 2
Compostable Polymeric Ecomaterials: Environment-Friendly Waste Management Alternative to Landfills
Sikorska, W., Musioł, M., Zawidlak-Węgrzyńska, B., & Rydz, J. (2019) · Springer eBooks · doi:10.1007/978-3-319-68255-6_36 · Cited by 4
The emerging frontiers in materials for functional three-dimensional printing
Lee, J. M., Sing, S. L., Goh, G. D., Goh, G. L., Ng, W. L., & Yeong, W. Y. (2022) · Elsevier eBooks · doi:10.1016/b978-0-323-95062-6.00008-5 · Cited by 2
Biomaterial-based fibers for enhanced wound healing and effective tissue regeneration
Mehra, L., & Gupta, P. (2023) · Elsevier eBooks · doi:10.1016/b978-0-323-96117-2.00005-4 · Cited by 4
Chanthaset, N., Maehara, A., & Ajiro, H. (2023) · Colloids and Surfaces A Physicochemical and Engineering Aspects · doi:10.1016/j.colsurfa.2023.131413 · Cited by 3
Sunil, A. K., Sarkar, K., & Chatterjee, K. (2016) · Journal of Modern Materials · doi:10.21467/jmm.1.1.9-16 · Cited by 2
Craniofacial Regenerative Medicine
Smith, B. T., Watson, E., Hanna, I. A., Melville, J. C., Mikos, A. G., & Wong, M. E.-K. (2018) · Elsevier eBooks · doi:10.1016/b978-0-12-809880-6.00050-3 · Cited by 3
Ryu, J., Kang, H.-S., Byung-Hun, K. A. N. G., et al. (2021) · Journal of Applied Oral Science · doi:10.1590/1678-7757-2020-1092 · Cited by 2
Strategies to optimize engineered tissue towards native human aortic valves
Balguid, A. (2008) · TU/e Research Portal · doi:10.6100/ir631898 · Cited by 2
“…biocompatibility, biodegradation to non toxic products, processability to complicated shapes, ability to support cell growth and proliferation, appropriate mechanical properties, as well as maintaining mechanical strength during the tissue regeneration process (Gunatillake and Adhikari, 2003).”
BackgroundZhao, L. (2007) · Digital Library of Theses and Dissertations (Universidade de São Paulo) · doi:10.11606/d.3.2007.tde-13082007-161004 · Cited by 4
Fitzgerald, R., & Vleggaar, D. (2010) · Wiley eBooks · doi:10.1002/9781444315004.ch6 · Cited by 2
Therapeutic Nanomaterials for Cartilage Regeneration
Arslan, E. N., Yaylacı, S., Guler, M. O., & Tekinay, A. B. (2016) · Wiley eBooks · doi:10.1002/9781118987483.ch4 · Cited by 2
“In addition, synthetic polymers are generally cheaper than natural polymers, can be produced in large quantities, and have longer shelf lives (Gunatillake and Adhikari, 2003; Kim and Mooney, 1998).”
BackgroundCharacterization of the Adhesive Interactions Between Cells and Biomaterials
Ferlin, K. M., Kaplan, D. S., & Fisher, J. P. (2013) · Wiley eBooks · doi:10.1002/9781118574775.ch7 · Cited by 2
Electrospinning Materials for Skin Tissue Engineering
Kınıkoğlu, B. (2016) · Wiley eBooks · doi:10.1002/9781119242628.ch1 · Cited by 2
Fan, X. (2019) · ThinkIR: The University of Louisville's Institutional Repository (University of Louisville) · doi:10.18297/etd/3335 · Cited by 2
“Nain et al. have developed a Spinneret-Based Tunable Engineered Parameters (STEP) technique to construct aligned microfibers using both PLA and PLGA.”
BackgroundInfluentialLin, Y., & Yelick, P. C. (2008) · Elsevier eBooks · doi:10.1016/b978-012369410-2.50077-2 · Cited by 2
Production of hard tissue scaffolds using three-dimensional printing method
Dávid, T. (2008) · Dublin City University Open Access Institutional Repository (Dublin City University) · Cited by 2
Biodegradable polymer nanocomposites for catalytic and photocatalytic applications
Pyarasani, R. D., Amalraj, J., Negi, P., Chandrasekaran, S., & Kalayar, S. (2023) · Elsevier eBooks · doi:10.1016/b978-0-323-91696-7.00020-9 · Cited by 2
Fernández‐Costa, J. M., Fernández‐Garibay, X., Ramón‐Azcón, J., & Tejedera‐Villafranca, A. (2024) · Elsevier eBooks · doi:10.1016/b978-0-323-91821-3.00018-9 · Cited by 1
Corvaglia, I., Al-Kharusi, G., Niclot, F. B., Manca, A., Levingstone, T. J., Little, S., Fiorilli, S., Dunne, N., & Vitale‐Brovarone, C. (2024) · Open Ceramics · doi:10.1016/j.oceram.2024.100542 · Cited by 1
Kumar, S., & Kumar, R. (2025) · Elsevier eBooks · doi:10.1016/b978-0-443-26516-7.00018-3 · Cited by 1
Wang, M.-W., Liu, J.-C., & Sung, M.-L. (2025) · Materials · doi:10.3390/ma18174192 · Cited by 1
“PLA, for instance, exhibits commendable strength and stiffness but suffers from brittleness and slow degradation; in contrast, PCL offers ductility and processability but possesses low strength and similarly slow resorption rates [4].”
Developing an Artificial Synovial Membrane Model Using Hyaluronic Acid-Binding Peptides
Mao, M., Thompson, F. C., Ballard, K., et al. (2025) · ACS Applied Bio Materials · doi:10.1021/acsabm.5c01205 · Cited by 1
Advancements in the Sustainable Recycling of Polymer Composites
Bera, S., Sangeeth, P. S., Parvanadev, K., Joseph, T. M., & Thomas, S. (2026) · Advanced structured materials · doi:10.1007/978-981-95-2469-3_17 · Cited by 1
Fabrication of Peptide Drug Delivery Formulations and Its Characterization Techniques: A Review
Regulagadda, S., Geddam, R., Vasa, T. R. P., Rudhrabatla, V. S. A. P., Thrimurthulu, G., & Padigapati, S. R. (2026) · International Journal of Peptide Research and Therapeutics · doi:10.1007/s10989-025-10798-9 · Cited by 1
Bone tissue engineering, scaffold requirements and the utilization of natural polymers
Fadahunsi, A. A., Johnson, M., Rahman, S., & Mason, M. D. (2026) · Cellulose · doi:10.1007/s10570-026-06985-6 · Cited by 2
Elsafty, M. E., Ghazala, M. A. A., Mabrouk, M., Tiama, T. M., Beherei, H. H., & Aboelnasr, M. A. (2026) · Journal of Drug Delivery Science and Technology · doi:10.1016/j.jddst.2026.108321 · Cited by 1
New Developments in Tissue Engineering of Microvascular Prostheses
Vindigni, V., Abatangelo, G., & Bassetto, F. (2011) · InTech eBooks · doi:10.5772/24899 · Cited by 3
Zmiany wybranych właściwości polilaktydu zachodzące pod wpływem jego trzykrotnego przetwarzania
Malinowski, R., & Łubkowski, D. (2012) · Inżynieria i Aparatura Chemiczna · Cited by 1
Fabrication of PGA/PLA Scaffold with the Shape of Human Nose
Li, Q., Zhang, L., Zhou, G., et al. (2013) · InTech eBooks · doi:10.5772/55540 · Cited by 1
“However, the most widely used form of PGA material in cartilage engineering is unwoven fiber mesh, which is difficult to be initially prepared into a complicated 3D structure and would most likely fail to maintain its original architecture during subsequent in vitro chondrogenesis due to insufficient mechanical suppor…”
BackgroundNobori®drug-eluting stent system: current data on a novel stent
Danzi, G. B., Chevalier, B., & Mitsudo, K. (2012) · Interventional Cardiology · doi:10.2217/ica.12.20 · Cited by 1
In Vitro Degradation of Poly-L-DL-Lactic Acid (PLDLLA) after Two Processing Methods
Coimbra, M. E. R., Bernardes, M. G., Elias, C. N., & Coelho, P. G. (2014) · Journal of biomimetics, biomaterials and biomedical engineering · doi:10.4028/www.scientific.net/jbbbe.20.45 · Cited by 3
“It is general consensus that bioresorbable implants should effectively degrade and eventually be fully resorbed or excreted by the body [13-15].”
BackgroundKim, N.-S., Yun, K., Vang, M.-S., Yang, H.-S., Lim, H.-P., Kang, S.-S., & Park, S.-W. (2010) · The Journal of Korean Academy of Prosthodontics · doi:10.4047/jkap.2010.48.2.158 · Cited by 1
Meniscal lesions and their healing: New aspects
Saadinam, F., Fattahian, H., & Kajbafzadeh, A. (2014) · Comparative Clinical Pathology · doi:10.1007/s00580-014-2017-4 · Cited by 1
“…(PVA-H) (Kobayashi et al. 2003), wedge-shaped three-ply silk scaffold (Mandal et al. 2011), micro-porous polyurethane amide, polyurethane-urea (Gunatillake and Adhikari 2003), polyglucuronic acid, poly-lactic acid (Van der Bracht et al. 2007), poly-l-lactic acid (PLLA) cylinder, and sponge…”
Uzel, A. P., Elodie, S., Henri, S., et al. (2012) · Key engineering materials · doi:10.4028/www.scientific.net/kem.529-530.325 · Cited by 1
Current Strategies in Osteochondral Repair with Biomaterial Scaffold
Shimomura, K., Moriguchi, Y., Sugita, N., et al. (2015) · Springer eBooks · doi:10.1007/978-3-319-20777-3_23 · Cited by 1
Savvidis, P., Givissis, P., Apostolou, T. S., Christodoulou, A. G., & Papalois, A. E. (2015) · Cited by 1
Cryogels for Neural Tissue Engineering
Vishnoi, T., & Kumar, A. (2016) · CRC Press eBooks · doi:10.1201/b19676-12 · Cited by 1
Emerging Orthobiologic Approaches to Tendon Injuries
Canata, G. L., Casale, V., Carli, A. D., Zanon, G., Benazzo, F. M., Rivellino, M. C., Vascellari, A., & Oliva, F. (2017) · Springer eBooks · doi:10.1007/978-3-662-54181-4_22 · Cited by 1
Microfluidic Chip-based Fabrication Of Hollow Alginate Microfiber For Enzyme Entrapment And Reaction
Pham, U. H. T. (2014) · UTA ResearchCommons (University of Texas Arlington) · Cited by 1
TISSUE ENGINEERING IN PEDIATRIC UROLOGY
Lakshmanan, Y., & Purves, J. T. (2009) · Elsevier eBooks · doi:10.1016/b978-1-4160-3204-5.00015-3 · Cited by 1
Bio-Engineered Meniscus for Tissue Engineering
Azhim, A., Ibrahim, N., & Yusof, F. M. (2019) · IntechOpen eBooks · doi:10.5772/intechopen.80553 · Cited by 2
“To add, other bioabsorbable synthetic polymers, such as polyurethane (PU), polyglycolic acid (PGA), polylactic acid, and poly (ε- caprolactone) (PCL) are also widely studies to play important part in supporting the development of meniscal scaffolds [8, 9].”
BackgroundPraveen, G. L., Kalarikkal, N., & Thomas, S. (2019) · Elsevier eBooks · doi:10.1016/b978-0-12-815751-0.00014-6 · Cited by 1
Breast tissue engineering: implantation and three-dimensional tissue test system applications
Burg, K. J. L., & Burg, T. C. (2020) · Elsevier eBooks · doi:10.1016/b978-0-12-818422-6.00031-9 · Cited by 1
Regenerative Implants for Cardiovascular Tissue Engineering
Lee, A. Y., Lee, Y., Mahler, N., Best, C. A., Tara, S., & Breuer, C. K. (2015) · Elsevier eBooks · doi:10.1016/b978-0-12-800548-4.00004-8 · Cited by 1
Mariyanats, A. O., Mironov, A. V., Nifant'ev, I. E., Shlyakhtin, A. V., & Popov, V. K. (2020) · IOP Conference Series Materials Science and Engineering · doi:10.1088/1757-899x/848/1/012107 · Cited by 1
Engineering of tissues and organs
Lee, S. J., & Atala, A. (2014) · Elsevier eBooks · doi:10.1533/9780857097163.3.347 · Cited by 4
PCL-based bionanocomposites in tissue engineering and regenerative medicine
Yadav, A. L., Gurave, P. M., Gadkari, R. R., & Ali, S. W. (2021) · Elsevier eBooks · doi:10.1016/b978-0-12-821280-6.00018-0 · Cited by 1
Polyacrylamide Injection vs. Polylactic Acid in HIV Related Lipodystrophy: A RCT Systematic Review
Tartaro, G., Pinto, L., Giudice, G. L., Fragola, R., Bove, P., Rauso, G. M., Zerbinati, N., & Colella, G. (2021) · Applied Sciences · doi:10.3390/app11178195 · Cited by 1
Enzyme-encapsulated nanoparticles for biodegradation of materials
Balan, L., Sanker, J., Chandrasekaran, S., & Vallinayagam, S. (2021) · Elsevier eBooks · doi:10.1016/b978-0-12-823970-4.00007-5 · Cited by 1
Tanzi, M. C., Farè, S., & Candiani, G. (2019) · Elsevier eBooks · doi:10.1016/b978-0-08-101034-1.00008-6 · Cited by 1
Functions and Requirements of Synthetic Scaffolds in Tissue Engineering
Karande, T. S., Kaufmann, J., & Agrawal, C. M. (2014) · CRC Press eBooks · doi:10.1201/b17444-5 · Cited by 2
Biomaterials Degradation and Bioabsorbability: Biomedical Potentials of Marine Enzymes
Guo, K. W. (2019) · Springer eBooks · doi:10.1007/978-3-319-68255-6_160 · Cited by 1
POLYCAPROLACTONE NANOPARTICLES AS DELIVERY VEHICLE IN COMBATING DISEASES
Mandal, A. K. (2022) · Indian Journal Of Applied Research · doi:10.36106/ijar/4914373 · Cited by 1
A Systematic Review on Electrospun Polymer Nanocomposites Used for Bone Tissue Engineering
Maheshwari, S. U., Govindan, K., & Devaraj, I. (2023) · Biophysical Reviews and Letters · doi:10.1142/s179304802331001x · Cited by 1
Patel, T. B., Padhiyar, S., Prajapati, V. T., et al. (2023) · International Journal of Pharmaceutical Investigation · doi:10.5530/ijpi.14.1.27 · Cited by 1
Developing Biodegradable Polymeric Composite for Nails Manufacturing of Bone Fracture Fixation
Yousry, A., Mustafa, H. M. M., Abdelmoez, W., El-Wakad, M. T., & Abdo, M. S. E. (2024) · Egyptian Journal of Chemistry · doi:10.21608/ejchem.2024.257443.9038 · Cited by 2
Biomaterials for Peripheral Nerve Injury Repair
Wu, J., Guo, H., Chen, L., Wang, Y., & Sun, L. J. (2023) · Journal of Biomaterials and Tissue Engineering · doi:10.1166/jbt.2023.3344 · Cited by 2
Pankongadisak, P., Jaiong, S., Sirimethawong, Y., Chuenjitkuntaworn, B., Supaphol, P., & Suwantong, O. (2024) · Emergent Materials · doi:10.1007/s42247-024-00702-4 · Cited by 1
Banimohamad‐Shotorbani, B., Rahbarghazi, R., Jarolmasjed, S., Mehdipour, A., & Shafaei, H. (2024) · Bioimpacts · doi:10.34172/bi.30006 · Cited by 1
“19 Poly-caprolactone (PCL), 17,20 poly L-lactide and its copolymers, 17,21 chitosan, 22 silk fibroin, 23 etc, are commonly used in the fabrication of scaffolds with the potential to improve bone healing by promoting the proliferation and differentiation of seeded cells.”
BackgroundGad, S., AL-Thamarani, S., Hammady, T. M., & Hammadi, S. H. (2024) · Records of Pharmaceutical and Biomedical Sciences/Records of Pharmaceutical & Biomedical Sciences · doi:10.21608/rpbs.2024.275350.1279 · Cited by 1
Features of Polymer Modification in a Supercritical Carbon Dioxide Environment
Solovieva, A. B., & Timashev, P. S. (2024) · Polymer Science Series C · doi:10.1134/s181123822460023x · Cited by 3
Biodegradable Materials for Customized Medical Devices Improve Personalized Medicine
Sharma, R., Malviya, R., Patel, M., & Raval, D. (2025) · Springer eBooks · doi:10.1007/978-3-031-79110-9_12 · Cited by 1
Growth Plate Regeneration Using Polymer-Based Scaffolds Releasing Growth Factor
Clark, A. M. (2013) · UKnowledge (University of Kentucky) · Cited by 1
Surface Modification of Carbon Nanotubes (CNTs) for Composites
Lee, J., Kim, N. S., Kumar, N., & Basavarajaiah, S. (2010) · CRC Press eBooks · doi:10.1201/b10462-10 · Cited by 1
(2014) · WORLD SCIENTIFIC eBooks · doi:10.1142/9789814612128_0004 · Cited by 1
The Development of in-Situ, Photo Crosslinked, Citric Acid Based Polymeric Delivery Systems
Dhaliwal, K. (2019) · Biomedical Journal of Scientific & Technical Research · doi:10.26717/bjstr.2019.13.002441 · Cited by 1
“This was demonstrated by Dunn, who crosslinked biodegradable copolymers D, L lactide and L-lactide with ε-caprolactone, using a chemically initiated thermo-set system, for use as a slow-release drug delivery system.”
BackgroundElectrospun Polycaprolactone for Controlled Drug Delivery
Bajsić, E. G., Ferri, T. Z., Trcin, M. T., Grgurić, T. H., Mijović, B., & Zdraveva, E. (2019) · Kemija u industriji · doi:10.15255/kui.2019.007 · Cited by 1
Spatiotemporal Controls of Tooth-Supportive Structure Neogenesis by 3D Printing Technology
Cho, Y., Giannobile, W. V., Sarment, L., & Park, C. H. (2020) · Springer eBooks · doi:10.1007/978-3-030-42990-4_16 · Cited by 1
Sultana, S., Mamatha, D. M., & Rahamathulla, S. (2020) · Learning and analytics in intelligent systems · doi:10.1007/978-3-030-46939-9_20 · Cited by 1
Kruk, A., Gadomska‐Gajadhur, A., Dulnik, J., & Ruśkowski, P. (2020) · International Journal of Polymeric Materials · doi:10.1080/00914037.2020.1798440 · Cited by 2
Ranjith, R. (2020) · International Journal for Research in Applied Science and Engineering Technology · doi:10.22214/ijraset.2020.32351 · Cited by 1
Nanobiomaterials for wound healing
Rajput, A., Keshari, R., Patil, R., et al. (2022) · Elsevier eBooks · doi:10.1016/b978-0-12-819469-0.00004-6 · Cited by 1
(2019) · Elsevier eBooks · doi:10.1016/b978-0-323-47821-2.00016-0 · Cited by 2
Koldewijn, E. L., Oerlemans, D. J. A. J., Beulens, A. J. W., et al. (2022) · Urogynaecologia · doi:10.4081/uij.2022.287 · Cited by 1
BIOMATERIALS WITH ENHANCED BIOLOGICAL FUNCTIONS FOR MEDICAL APPLICATIONS
Balint, R., Paltinean, G. A., Tomoaia, G., Oltean‐Dan, D., Mocanu, A., & Tomoaia-Cotişel, M. (2021) · Annals of the Academy of Romanian Scientists Series on Biological Sciences · doi:10.56082/annalsarscibio.2021.1.90 · Cited by 2
Intelligent Drug Delivery Systems
Mirić, A. N., & Milivojević, N. N. (2023) · Lecture notes in networks and systems · doi:10.1007/978-3-031-29717-5_21 · Cited by 1
Голубева, Е. Н., & Чумакова, Н. А. (2020) · Сверхкритические флюиды. Теория и практика. · doi:10.34984/scftp.2018.13.3.004 · Cited by 1
Current Applications of Biotextiles and Future Trends
Gajjar, C. R., & King, M. W. (2014) · SpringerBriefs in materials · doi:10.1007/978-3-319-08305-6_7 · Cited by 1
Investigations on biocomposites from oat hull and biodegradable polymers
Grewal, R. (2016) · University Library - University of Saskatchewan (University of Saskatchewan) · Cited by 1
Cell‐Based Nanocomposites and Biomolecules for Bone Tissue Engineering
Ngiam, M., Liao, S., Chan, C. K., & Ramakrishna, S. (2009) · Wiley eBooks · doi:10.1002/9780470891315.ch16 · Cited by 1
Petersen, L. K. (2011) · Iowa State University Digital Repository (Iowa State University) · doi:10.31274/etd-180810-333 · Cited by 1
Sustained release injectables formed "in-situ" for veterinary use
Sautter, C. A. F. (2006) · edoc (University of Basel) · doi:10.5451/unibas-004112998 · Cited by 1
Where Are We Going? Future Trends and Challenges
Lee, S. J., & Atala, A. (2014) · Wiley eBooks · doi:10.1002/9781118356692.ch11 · Cited by 1
Differentiation of Mouse Stem Cells into Neural Cells on PLGA Microspheres Scaffold
Nojehdehyan, H., Moztarzadeh, F., Mehrjerdi, N. Z., et al. (2007) · Iranian journal of pharmaceutical sciences · Cited by 1
Controlled drug release from multi-phase polymeric particles
Lee, W. L. (2012) · DR-NTU (Nanyang Technological University) · doi:10.32657/10356/48050 · Cited by 1
Biological evaluation of biomaterials for bone tissue regeneration
Ps, G. (2011) · Portuguese National Funding Agency for Science, Research and Technology (RCAAP Project by FCT) · doi:10.34626/mf5d-dc29 · Cited by 2
Synthesis of Stimuli-responsive Hydrogels from Glycerol
Salehpour, S. (2012) · Library and Archives Canada (Government of Canada) · doi:10.20381/ruor-5373 · Cited by 1
An implantable sustained-release chemotherapy delivery system for the treatment of breast cancer
Chen, Y. (2015) · doi:10.31274/etd-180810-4369 · Cited by 1
“One is PGA’s high sensitivity to hydrolytic degradation requires devising precise processing [40].”
BackgroundSchoener, C. A. (2010) · OakTrust (Texas A&M University Libraries) · Cited by 2
Three-dimensional printing of biodegradable polymeric scaffold
Tan, H. T. (2007) · DR-NTU (Nanyang Technological University) · doi:10.32657/10356/21250 · Cited by 1
Washington, M. A. (2017) · D-Scholarship@Pitt (University of Pittsburgh) · Cited by 1
Gil-Castell, O. (2018) · RiuNet (Universitat Politècnica de València) · doi:10.4995/thesis/10251/107950 · Cited by 1
3-D direct printing of silicone meniscus using a novel heat-curing extrusion based silicone printer
Adiwati, G. E. L. (2019) · DR-NTU (Nanyang Technological University) · doi:10.32657/10356/85163 · Cited by 1
Biomaterials for Tissue Engineering – Bioabsorbability/Degradation in Marine Biotechnology
Guo, K. W., & Tam, H.-Y. (2020) · Wiley eBooks · doi:10.1002/9781119143802.ch33 · Cited by 1
Intestinal organoids as new treatments for inflammatory bowel disease
Davoudi, Z. (2020) · Iowa State University Digital Repository (Iowa State University) · doi:10.31274/etd-20210114-37 · Cited by 1
Natural Biopolymers for Tissue Engineering
Sarkar, K., Ghosh, D., Banerjee, K., Neog, T. T., & Patra, R. (2024) · Wiley eBooks · doi:10.1002/9783527848133.ch29 · Cited by 1
Metadata
- Authors
- CSIRO Molecular Science, B. 1., & Gunatillake, P.
- Corresponding author
- CSIRO Molecular Science, Bag 10, Clayton South MDC, Vic 3169, Australia
- Venue
- European Cells and Materials
- Publisher
- Forum Multimedia Publishing LLC
- Published
- 2003-10-01
- Volume
- 5
- Pages
- 1-16
- ISSN
- 1473-2262 (ISSN-L)
- OpenAlex
- W2106035984
- Cited by
- 1,765
- References
- 97
- Citations by year
- 2026: 43 · 2025: 61 · 2024: 59 · 2023: 80 · 2022: 90 · 2021: 112 · 2020: 102 · 2019: 115 · 2018: 105 · 2017: 128 · 2016: 110 · 2015: 106 · 2014: 110 · 2013: 91 · 2012: 86
- FWCI
- 1.32
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- cc-by
- Locations
- European Cells and Materials (publishedVersion, cc-by)
- PubMed (publishedVersion)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion)
- Topics
- Physical Sciences › Materials Science › Biomaterials › biodegradable polymer synthesis and properties
- Physical Sciences › Engineering › Biomedical Engineering › Bone Tissue Engineering Materials
- Health Sciences › Medicine › Surgery › Surgical Sutures and Adhesives
- Keywords
- tissue engineering, polyesters, polyglycolic acid, polylactic acid, polyanhydrides, polyphosphazenes, polyurethane, poly(propylene fumarate), injectable polymers, orthopedic tissue engineering, biodegradation, biocompatibility, degradation products
- MeSH terms
- Biocompatible Materials, Models, Chemical, Polymers, Tissue Engineering
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.