Biodegradable synthetic polymers for tissue engineering
Open accessThe DOI matches its Crossref record; 96 of the 97 references it cites were found in a registry or an index; 1 of the 146 sources its claims cite were checked for support.
Abstract
This review focuses on biodegradable synthetic polymers, discussing synthesis, properties and biodegradability, especially within the polyester family including polylactides.
Overview
CoChat Summary
TL;DR
This review surveys biodegradable synthetic polymers for tissue engineering, emphasizing polyesters (PGA, PLA, PLGA), polylactones, poly(propylene fumarate), polyanhydrides, tyrosine-derived polycarbonates, polyorthoesters, polyurethanes, and polyphosphazenes. It concludes that polyesters dominate clinically, while injectable in situ curable systems such as PPF and photocrosslinkable polyanhydrides are promising but face challenges in biocompatibility, degradation control, and heat generation.
Key findings
- Polyesters are the most studied biodegradable polymers. PGA has 46–50% crystallinity, Tg 36°C, Tm 225°C; in Dexon sutures in vitro, first-stage degradation predominates for 21 days, crystalline degradation takes a further 28 days, and after 49 days weight loss was about 42% with complete loss of mechanical properties.
- PLA/PGA copolymer behavior depends on composition: 25–75% (l)LA/GA and 0–70% (dl)LA/GA are amorphous; 70/30 GA/LA has the highest water uptake, while 50/50 is reported as most unstable to hydrolysis; Vicryl is 8% (l)LA and 92% GA.
- Poly(caprolactone) degrades slowly: homopolymer degradation is on the order of 2–3 years, and PCL with initial average molecular weight 50,000 takes about 3 years for complete in vitro degradation.
- Poly(propylene fumarate) degrades to fumaric acid and propylene glycol; time to 20% original weight loss ranged from 84 days (PPF/β-TCP composite) to over 200 days (PPF/CaSO4 composite). PPF formulations showed maximum curing temperatures of 38–48°C versus 94°C for PMMA cements, curing times of 1–121 min, and compressive strengths of 1–12 MPa.
- Polyanhydrides degrade by surface erosion; poly(sebacic acid) degrades in about 54 days in saline, while poly(1,6-bis(p-carboxyphenoxy)hexane) is estimated at 1 year. Poly[1,6-bis(carboxyphenoxy)hexane] has a Young’s modulus of 1.3 MPa versus human bone at 40–60 MPa; poly(anhydride-co-imides) reached compressive strengths of 50–60 MPa, and photocrosslinked systems showed compressive strengths of 30–40 MPa and tensile strengths of 15–27 MPa.
- Degradable polyurethanes based on lysine diisocyanate showed varied properties: dl-lactide networks were rigid (Tg = 60°C) with ultimate tensile strengths of ~40–70 MPa, caprolactone triol networks were low-modulus elastomers with tensile strengths of 1–4 MPa, and copolymer networks had elongation up to 600% with compressive strengths of 3–25 MPa. In vivo, porous polyurethane artificial skin degraded almost completely 4–8 weeks after implantation in guinea pigs with no adverse tissue reaction.
Methods
- Design: narrative literature review; no primary experimental study or systematic review protocol is reported.
- Data/sample: published literature on biodegradable synthetic polymers, including synthesis, properties, degradation, biocompatibility, and injectable polymer systems; Tables 1–3 summarize polymer properties and precursors.
- Analysis: qualitative synthesis of major polymer classes, their degradation modes/products, mechanical properties, biocompatibility, and potential for injectable tissue-engineering compositions.
Limitations
- Stated: the paper notes that Table 2 data “should be used as a guide only” and that sufficient data are not available to provide a comprehensive list of properties for polyanhydrides, polycarbonates, polyurethanes, and polyphosphazenes.
- Stated: for polyanhydrides, no data are reported about polymer sterilizability and heat generation during polymerization; for degradable polyurethanes, the effect of degradation products and how they are removed from the body are not clearly understood.
- Evident: as a narrative review, it lacks systematic search criteria, study quality appraisal, and meta-analysis, so conclusions depend on the cited literature and may not comprehensively cover all biodegradable polymers or tissue-engineering applications.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
1 Valid · 20 Not valid · 105 Not checked · 89 Own results and interpretations
Every source the paper cites for this claim was checked and supports it.
In the paper
“A meniscal replica implanted contained only fibro-cartilage after 18 weeks and decreased the degradation of the articular cartilage.”
What the sources say
- Supportedcites De Groot et al.., 1996 source
The Aliphatic PU network passage (page not provided) reports that articular-cartilage degeneration was less severe with the prosthesis than in meniscectomized control knees. It also says the prostheses contained only fibrocartilage after 18 weeks. Degeneration was reduced, not eliminated. (LLM, conf=0.91)
plainstates a causeSingle case- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
In the paper
“The compressive strengths varied between 1 and 12 MPa”
What the sources say
- Not matchedcites Peter et al., 1998a
Couldn’t be matched to a paper in Crossref, so it can’t be checked.
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Not matched
In the paper
“Cross-linking characteristics reported for PPF, N-vinyl pyrrolidone (N-VP), benzoyl peroxide, sodium chloride, and TCP indicate that for a range of formulations, the maximum temperature varied within 38 to about 48ºC, compared to 94ºC observed for polymethylmethacrylate (PMMA) cements.”
What the sources say
- Not matchedcites Peter et al., 1998a
Couldn’t be matched to a paper in Crossref, so it can’t be checked.
hedged- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Not matched
None of the sources cited for this claim could be matched to a paper in Crossref, so there is nothing to check it against.
In the paper
“Based on in-vitro studies, the time required to reach 20% loss in original weight ranged from 84 (PPF/ß-TCP composite) to over 200 days (PPF/CaSO 4 composite)”
What the sources say
- Not matchedcites Peter et al., 1997b
Couldn’t be matched to a paper in Crossref, so it can’t be checked.
- Not matchedcites Kharas et al., 1997
Couldn’t be matched to a paper in Crossref, so it can’t be checked.
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Not matched
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“These composite materials exhibit compressive strengths in the range 2 to 30 MPa.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
94 more claims
Create a free account to see all 215 claims and to verify the 2 references still open.
- It may state two separate claims as one. 62
- Probably not a substantial claim. 76
- The quote only partly states this claim. 1
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“Advantages include a tightly controlled manufacturing process, accurate reproducibility, adjustable biodegradability, and a wide variety of both chemical and physical properties.[ 171 ]”
From Unraveling and Harnessing the Immune Response at the Cell–Biomaterial Interface for Tissue Engineering Purposes (2024) · cites this paper as [171]
Experimental — accuracy not yet measured
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
§ Polyanhydrides
“Polyanhydrides degrades by surface erosion (Kohn and Langer, 1997) and their main applications are in controlled drug delivery.”
§ Conclusions
“Polyanhydride degrade by bulk erosion and their main applications are in controlled drug delivery.”
Citations
Cites
Synthetic biodegradable polymers as orthopedic devices
Middleton, J. C., & Tipton, A. J. (2000) · Biomaterials · doi:10.1016/s0142-9612(00)00101-0 · Cited by 2,741 · cited 4×
“…developments in siloxane-based polyurethanes, which have greater in-vivo stability than conventional polyetherurethanes (e.g., poly(tetramethylene oxide) (PTMO)-based) have provided opportunities for development of a range of medical implants for chronic applications (Gunatillake et al., 2001).”
BackgroundInfluentialBiomaterial developments for bone tissue engineering
Burg, K. J. L., Porter, S., & Kellam, J. F. (2000) · Biomaterials · doi:10.1016/s0142-9612(00)00102-2 · Cited by 1,643 · cited 1×
“Polyesters have also been considered for development of tissue engineering applications (Hubbell, 1995; Thomson et al 1995a, Yazemski et al. 1996; Wong and Mooney, 1997), particularly for bone tissue engineering (Kohn and Langer, 1997; Burg et al., 2000).”
BackgroundChandra, R. (1998) · Progress in Polymer Science · doi:10.1016/s0079-6700(97)00039-7 · Cited by 1,462
Biodegradable polymers for use in surgery—polyglycolic/poly(actic acid) homo- and copolymers: 1
Gilding, D. K., & Reed, A. M. (1979) · Polymer · doi:10.1016/0032-3861(79)90009-0 · Cited by 1,345
Biomaterials in Tissue Engineering
Hubbell, J. A. (1995) · Nature Biotechnology · doi:10.1038/nbt0695-565 · Cited by 1,060 · cited 1×
“Polyesters have also been considered for development of tissue engineering applications (Hubbell, 1995; Thomson et al 1995a, Yazemski et al. 1996; Wong and Mooney, 1997), particularly for bone tissue engineering (Kohn and Langer, 1997; Burg et al., 2000).”
BackgroundPolylactic Acid for Surgical Implants
KULKARNI, R. K. (1966) · Archives of Surgery · doi:10.1001/archsurg.1966.01330050143023 · Cited by 841
Evolution of bone transplantation: molecular, cellular and tissue strategies to engineer human bone
Yaszemski, M. J., Payne, R. G., Hayes, W. C., Langer, R., & Mikos, A. G. (1996) · Biomaterials · doi:10.1016/0142-9612(96)85762-0 · Cited by 729
Miller, R. A., Brady, J. M., & Cutright, D. E. (1977) · Journal of Biomedical Materials Research · doi:10.1002/jbm.820110507 · Cited by 722 · cited 2×
“For the (l)LA/GA copolymers, resistance to hydrolysis is more pronounced at either end of the copolymers compositions range (Miller et al., 1977; Gilding and Reed, 1979; Reed and Gilding, 1981; Vert et al., 1984).”
BackgroundInjectable biodegradable materials for orthopedic tissue engineering
Temenoff, J. S., & Mikos, A. G. (2000) · Biomaterials · doi:10.1016/s0142-9612(00)00108-3 · Cited by 554 · cited 8×
“A number of methods have been reported to prepare PPF, and each results in different polymer properties (Peter et al., 1997a,b, 1999; Temenoff and Mikos 2000).”
BackgroundMethodInfluentialLeong, K. W., Brott, B. C., & Langer, R. (1985) · Journal of Biomedical Materials Research · doi:10.1002/jbm.820190806 · Cited by 541 · cited 12×
“The polyurethanes ranged from elastomers with elongations at break as high as 780 %, but with low tensile strengths (5.8 to 8.1 MPa).”
BackgroundInfluential
Research works printed but not linked: 5
- Scranton A, Bowman C, Peiffer R, eds. ACS Symposium Series 673; American Chemical Society, Washington DC. pp 189-202.
- Ratner BD, Hoffman AS, Schoen FJ, Lemon JE, eds. Aca- demic Press, San Diego. pp 65-73.
- Lamba NMK, Woodhouse KA, Cooper SL (1998) Poly- urethanes in Biomedical Applications. CRC Press: New York p 205-241.
- Mark JE, Alcock HR, West R (1992) Inorganic Poly- mers. Prentice Hall, Upper Saddle River, NJ. Chapter
- Ng SY, Vandamme T, Tayler MS, Heller J (1997) Syn- thesis and erosion studies of self-catalysed poly(orthoester)s. Macromolecules 30: 770-772.
Cited by
Items 1,101–1,200 of 1,762
Scaffolds for epithelial tissue engineering customized in elastomeric molds
Abdallah, M., Abdollahi, S., Laurenti, M., et al. (2017) · Journal of Biomedical Materials Research Part B Applied Biomaterials · doi:10.1002/jbm.b.33897 · Cited by 9
“However, few studies explored their application in soft tissue regeneration, such as epithelial tissue regeneration.(5,11,12) Thus, the main aim of the current study is to fabricate customized PDLLA scaffolds with a pore structure that promotes attachment and proliferation of epithelial cells.”
BackgroundRuiz‐Velasco, G., Martínez‐Flores, F., Morales‐Corona, J., et al. (2017) · Macromolecular Symposia · doi:10.1002/masy.201600133 · Cited by 9
Multidimensional mass spectrometry characterization of isomeric biodegradable polyesters
Sallam, S., Luo, Y., Becker, M. L., & Wesdemiotis, C. (2017) · European Journal of Mass Spectrometry · doi:10.1177/1469066717711401 · Cited by 10
“Such materials are utilized in a wide range of medical and ecological applications,(2) including drug delivery, nanomedicine and tissue engineering.(4,5) Their bone tissue engineering applications have been widely investigated in the last decades.”
BackgroundErmolenko, Y. V., Semyonkin, A. S., Ulianova, Y. V., Kovshova, T. S., Максименко, О. О., & Gelperina, S. E. (2020) · Russian Chemical Bulletin · doi:10.1007/s11172-020-2918-0 · Cited by 9
Polyglycolic Acid-Induced Inflammation: Role of Hydrolysis and Resulting Complement Activation
Ceonzo, K., Gaynor, A. M., Shaffer, L. A., et al. (2006) · Tissue Engineering · doi:10.1089/ten.2006.12.ft-21 · Cited by 9
Cell attachment studies on electrospun nanofibrous PLGA and freeze-dried porous PLGA
Salamian, N., Irani, S., Zandi, M., Saeed, M., & Atyabi, S. M. (2013) · doi:10.1234/nano130103 · Cited by 11
Histopathology of the three implanted degradable biopolymers in rabbit eye
Rönkkö, S., Rekonen, P., Sihvola, R. K., Kaarniranta, K., Puustjärvi, T., Teräsvirta, M. E., & Uusitalo, H. M. T. (2008) · Journal of Biomedical Materials Research Part A · doi:10.1002/jbm.a.31932 · Cited by 9
Phospholipid–polyurethane adhesion force observed by atomic force microscopy
D’Acunto, M., Ciardelli, G., Narducci, P., Rechichi, A., & Giusti, P. (2005) · Materials Letters · doi:10.1016/j.matlet.2005.01.028 · Cited by 9
Design of Supermacroporous Biomaterials via Gelation at Subzero Temperatures—Cryogelation
Plieva, F. M., Kumar, A., Galaev, I. Y., & Mattìasson, B. (2009) · doi:10.1002/9780470891315.ch14 · Cited by 9
Polyester Materials in Biomedical Applications
Dil, E. J., Ajji, A., & Saffar, A. (2023) · Wiley eBooks · doi:10.1002/9781119535775.ch8 · Cited by 15
Lepekhina, T. B., Nikolaev, V. V., Darvin, M. E., Zuhayri, H., Snegerev, M. S., Lozhkomoev, A. S., Senkina, E. I., Kokhanenko, A. P., Lozovoy, K. A., & Kistenev, Y. V. (2024) · International Journal of Molecular Sciences · doi:10.3390/ijms25042257 · Cited by 9
“Non-toxicity and biocompatibility are important characteristics of the materials used for the manufacture of osteoimplants, but, recently, special attention has been paid to the development of materials with bioresorption [5,6].”
BackgroundJanczak, K., Mazuryk, A., Lisewska, D., Puszczykowska, N., & Fiedurek, K. (2024) · International Biodeterioration & Biodegradation · doi:10.1016/j.ibiod.2024.105950 · Cited by 9
Advances in Cytosolic Delivery of Proteins: Approaches, Challenges, and Emerging Technologies
Zhang, W., Liu, H., Zhu, B., Li, W., Han, X., Fu, J., Luo, R., Wang, H., & Wang, J. (2025) · Chemistry & Biodiversity · doi:10.1002/cbdv.202401713 · Cited by 12
Aydin, M. S., Nicolae, C.-V., Campodoni, E., Mohamed‐Ahmed, S., Kadousaraei, M. J., Yassin, M. A., Gjerde, C., Sandri, M., Stancu, I., Rashad, A., et al. (2025) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.5c03945 · Cited by 8
Hofmann, D., Entrialgo, M., Reiche, J., et al. (2010) · Advances in science and technology · doi:10.4028/www.scientific.net/ast.76.16 · Cited by 8
Rezayan, A. H., Firoozi, N., Kheirjou, S., et al. (2017) · PubMed · Cited by 8
Pasaribu, K. M., Mahendra, I. P., Sholeha, N. A., Masruchin, N., Mardawati, E., & Karina, M. (2024) · Green energy and technology · doi:10.1007/978-981-99-7769-7_10 · Cited by 10
Sierakowska-Byczek, A., Gałuszka, A., Janus, Ł., & Radwan-Pragłowska, J. (2024) · Molecules · doi:10.3390/molecules29225376 · Cited by 8
Gagliardi, M., Bertero, A., Bardi, G., & Bifone, A. (2015) · Materials Science and Engineering C · doi:10.1016/j.msec.2015.10.054 · Cited by 8
Effect of Synthesis Parameters on Size of the Biodegradable Poly (L-Lactide) (PLLA) Microspheres
Hawari, A. A., Tham, C. Y., & Hamid, Z. A. A. (2013) · Advanced materials research · doi:10.4028/www.scientific.net/amr.858.60 · Cited by 8
“Biodegradable polymers such as poly (lactic acid) (PLA), poly (glycolic acid), and their copolymers are chosen based on their biological properties such as biodegradability that can be hydrolyzed without the presence of enzymes and then removed from the body naturally [5].”
BackgroundSmoak, M. M., Hogan, K. J., Kriegh, L., Chen, C., Terrell, L., Qureshi, A. T., Monroe, W. T., Gimble, J. M., & Hayes, D. J. (2015) · Journal of Nanoparticle Research · doi:10.1007/s11051-015-2985-6 · Cited by 9
“Key advantages include the ability to tailor mechanical properties and degradation kinetics to suit various applications [42].”
BackgroundInfluentialNaik, J., Mokale, V. J., Shevalkar, G. B., et al. (2013) · International Journal of Phytomedicine · Cited by 8
Electrospun scaffolds for cartilage regeneration
Horner, C. B., Low, K., & Nam, J. (2016) · Elsevier eBooks · doi:10.1016/b978-1-78242-452-9.00010-8 · Cited by 10
Cheng, C., Chuang, W., Lee, D., Xin, Z., & Chiu, C. (2017) · Macromolecular Rapid Communications · doi:10.1002/marc.201600702 · Cited by 8
Electrospun Biopolyesters: Hydrophobic Scaffolds with Favorable Biological Response
Azari, P., Azari, P., Hosseini, S., Murphy, B. P., & Martinez-Chapa, S. O. (2018) · Journal of Public Health International · doi:10.14302/issn.2641-4538.jphi-18-1975 · Cited by 8
“hydrolysis of the ester bonds, producing non-toxic degradation products [10].”
BackgroundRadiopaque scaffolds based on electrospun iodixanol/polycaprolactone fibrous composites
Perez, J. V. D., Singhana, B., Damasco, J. A., Lu, L., Behlau, P., Rojo, R. D., Whitley, E. M., Heralde, F. M., Melancon, A. D., Huang, S. Y., et al. (2020) · Materialia · doi:10.1016/j.mtla.2020.100874 · Cited by 11
Bioresorbable polymeric materials – current state of knowledge
Wiśniewska-Wrona, M., Rybak, Z., Wątrobiński, M., Struszczyk, M. H., Filipiak, J., & Szymonowicz, M. K. (2021) · Polimery · doi:10.14314/polimery.2021.1.1 · Cited by 8
Goder, D., Eshkol‐Yogev, I., Matsliah, L., et al. (2021) · Burns · doi:10.1016/j.burns.2021.07.006 · Cited by 8
Polymeric scaffolds for antitumor immune cell priming
Bhatt, K., Eggermont, L. J., & Bencherif, S. A. (2021) · Elsevier eBooks · doi:10.1016/b978-0-323-90949-5.00003-6 · Cited by 13
Jikei, M., Takeda, M., Kaneda, Y., Kudo, K., Tanaka, N., Matsumoto, K., Hikida, M., & Ueki, S. (2021) · ACS Omega · doi:10.1021/acsomega.1c03846 · Cited by 11
Özcan, M., Magini, E. B., Volpato, G. M., da Cruz, A. C. C., & Volpato, C. Â. M. (2022) · Journal of Prosthodontics · doi:10.1111/jopr.13484 · Cited by 8
Rosa, R. P., Ferreira, F. V., Santos, D. M. D., & Lona, L. M. F. (2022) · European Polymer Journal · doi:10.1016/j.eurpolymj.2022.111171 · Cited by 11
Long-Term Outcomes of Secondary Nasal Tip Plasty After Degradation of a Polycaprolactone (PCL) Mesh
Lee, S. H., Cho, J., & Lee, J. S. (2022) · Aesthetic Plastic Surgery · doi:10.1007/s00266-022-02839-1 · Cited by 8
“[12, 13] There is no clinical study describing the long-term outcomes of rhinoplasty using a PCL mesh from this point of view.”
BackgroundJin, Z., Lu, B., & Yan, X. (2022) · International Journal of Polymeric Materials · doi:10.1080/00914037.2022.2067537 · Cited by 8
“early studies of biodegradable implant materials for clinical applications were mainly based on natural polymers.([83]) The”
BackgroundA Comparative Study of Three Approaches to Fibre’s Surface Functionalization
Dulnik, J., Jeznach, O., & Sajkiewicz, P. (2022) · Journal of Functional Biomaterials · doi:10.3390/jfb13040272 · Cited by 10
Thijssen, Q., Parmentier, L., holsbeeck, K. V., et al. (2023) · Biomacromolecules · doi:10.1021/acs.biomac.2c01389 · Cited by 8
Direct-Writing Electrospun Functionalized Scaffolds for Periodontal Regeneration: In Vitro Studies
Bourdon, L., Attik, N., Belkessam, L., et al. (2023) · Journal of Functional Biomaterials · doi:10.3390/jfb14050263 · Cited by 8
“Our initial aim was to use two resorbable polymers in the scaffold—PCL and PLGA—that have biocompatible and resorbable properties uitab e for g iding tissue regeneration [50,51].”
MethodDresvyanina, E. N., Тагандурдыева, Н., Kodolova-Chukhontseva, V. V., Dobrovol’skaya, I. P., Kamalov, A., Nashchekina, Y. A., Нащекин, А. В., Иванов, А. Г., Yukina, G. Y., & Yudin, V. E. (2023) · Polymers · doi:10.3390/polym15132860 · Cited by 9
Kumawat, V. S., Saini, R. K., Agrawal, A. K., Khare, D., Dubey, A. K., Ghosh, S. B., & Bandyopadhyay‐Ghosh, S. (2023) · Journal of Polymers and the Environment · doi:10.1007/s10924-023-02977-w · Cited by 10
Multifunctional nanosystems for cancer therapy
Singh, A., Iyer, A. K., Amiji, M. M., & Ganta, S. (2013) · Elsevier eBooks · doi:10.1533/9780857096760.3.387 · Cited by 10
Pavelková, A., Kucharczyk, P., Zednı́k, J., & Sedlařík, V. (2014) · Journal of Polymer Research · doi:10.1007/s10965-014-0426-3 · Cited by 8
“Recently, advances have led to dozens of forms of polyanhydrides and their copolymers with polyesters or polyimides being prepared [1, 5, 6].”
BackgroundEvaluation of water uptake and mechanical properties of biomedical polymers
Vidović, E., Klee, D., & Höcker, H. (2013) · Journal of Applied Polymer Science · doi:10.1002/app.39624 · Cited by 8
Kanitkar, A., Chen, C., Smoak, M. M., Hogan, K. J., Scherr, T., Aita, G. M., & Hayes, D. J. (2014) · Journal of Biomaterials Applications · doi:10.1177/0885328214553961 · Cited by 8
“However, polyester mechanical strength is shown to decrease significantly early in the degradation process, accompanied by the release of acidic degradation products.(14) A successful bone scaffold must balance the necessary bone-like mechanical properties with porosity and interconnectivity.”
BackgroundSynthesis and characterization of a poly(ethylene glycol)–poly(simvastatin) diblock copolymer
Asafo-Adjei, T. A., Dziubla, T. D., & Puleo, D. A. (2014) · RSC Advances · doi:10.1039/c4ra10310f · Cited by 8
Mano, S. S., Uto, K., Aoyagi, T., & Ebara, M. (2016) · AIMS Materials Science · doi:10.3934/matersci.2016.1.66 · Cited by 8
“On the other hand, biodegradable, synthetic polymers such as poly (glycolic acid), poly (lactic acid), poly (p-dioxanone) are used in tissue engineering and clinical applications [30].”
BackgroundSchusser, S., Krischer, M., Bäcker, M., Poghossian, A., Wagner, P., & Schöning, M. J. (2015) · Analytical Chemistry · doi:10.1021/acs.analchem.5b00617 · Cited by 8
Lee, J. H., Woo, D. K., Kim, T. H., Kang, J. G., Yun, J., Park, J., Park, B., Kang, Y., Rho, G., Jang, S., et al. (2016) · Journal of Biomedical Materials Research Part A · doi:10.1002/jbm.a.35907 · Cited by 8
Tham, W. H., Wahit, M. U., Kadir, M. R. A., et al. (2013) · DOAJ (DOAJ: Directory of Open Access Journals) · Cited by 8
Bee, S., Liew, S., Ang, W., Sin, L. T., Bee, S., & Rahmat, A. R. (2017) · Journal of Vinyl and Additive Technology · doi:10.1002/vnl.21595 · Cited by 8
Ferrer, G. G., Liedmann, A., Niepel, M. S., Liu, Z.-M., & Groth, T. (2017) · Advances in polymer science · doi:10.1007/12_2017_26 · Cited by 9
Nikolskaya, E. D., Faustova, M. R., Mollaev, M. D., et al. (2018) · Russian Chemical Bulletin · doi:10.1007/s11172-018-2132-5 · Cited by 8
Bian, Y., Wei, Z., Wang, Z., Tu, Z., Zheng, L., Wang, W., Leng, X., & Li, Y. (2019) · Journal of Materials Chemistry B · doi:10.1039/c8tb02952k · Cited by 8
Jose, L., Hwang, A., Lee, C., Shim, K., Song, J. K., An, S. S. A., & Paik, H. (2020) · Polymer Chemistry · doi:10.1039/c9py01663e · Cited by 8
Silva, B. A. D., Valério, A., Cesca, K., et al. (2020) · ChemistrySelect · doi:10.1002/slct.202002399 · Cited by 8
Reckhenrich, A. K., Koch, C. A., Egaña, J. T., & Plank, C. (2012) · European Cells and Materials · doi:10.22203/ecm.v023a34 · Cited by 8
“Both polymers, PCL and PDLLA, are aliphatic polyesters, which underlie mainly hydrolytic degradation in vivo and in vitro (Gunatillake and Adhikari, 2003; Middleton and Tipton, 2000; Wintermantel and Ha, 2009).”
BackgroundXie, D., Park, J., Zhao, J., & Turner, C. H. (2007) · Journal of Biomaterials Applications · doi:10.1177/0885328206068691 · Cited by 8
“Over the past twenty years, however, only a few research groups have really focused on the development of injectable synthetic biodegradable polymer compositions [8,9].”
BackgroundFunctions and Requirements of Synthetic Scaffolds in Tissue Engineering
Karande, T. S., & Agrawal, M. (2008) · CRC Press eBooks · doi:10.1201/9781420051834.ch3 · Cited by 29
Design Strategies for Tissue Engineering Scaffolds
Papenburg, B. J. (2009) · University of Twente Research Information · doi:10.3990/1.9789490122393 · Cited by 10
Cernadas, T., Pereira, J., Melo, B. L., de Melo‐Diogo, D., Correia, I. J., Alves, P., & Ferreira, P. C. N. (2024) · Biomacromolecules · doi:10.1021/acs.biomac.4c00599 · Cited by 7
Song, P., Chen, H., Ma, H., Zhou, Y., & Zhang, Y. (2026) · Frontiers in Bioengineering and Biotechnology · doi:10.3389/fbioe.2026.1691953 · Cited by 12
“…include combining natural materials to enhance biological activity, designing a structure-function integrated structure, and adopting precise degradation regulation strategies to enhance its application effect in meniscus tissue repair (Gunatillake and Adhikari, 2003; Pulapura and Kohn, 1992).”
Polymers as Bioactive Materials-I: Natural and Non-degradable Polymers
Kaur, G. (2017) · Series in bioengineering · doi:10.1007/978-3-319-45716-1_2 · Cited by 7
Pastusiak, M., Dobrzyński, P., Kasperczyk, J., Sobota, M., Kaczmarczyk, B., & Janeczek, H. (2017) · Polymer International · doi:10.1002/pi.5379 · Cited by 8
Azine, Z., Moeini, M., Solouk, A., et al. (2023) · NANO · doi:10.1142/s1793292023500121 · Cited by 7
Recent advances in polymer-based scaffolds for cardiac tissue engineering
Amiryaghoubi, N., Fathi, M., & Javadzadeh, Y. (2024) · International Journal of Polymeric Materials · doi:10.1080/00914037.2023.2299799 · Cited by 7
“PCL indicates a degradation time reliant on its molecular weight [10] .”
Basile, M. A., d’Ayala, G. G., Laurienzo, P., et al. (2012) · Journal of Applied Biomaterials & Functional Materials · doi:10.5301/jabfm.2012.10374 · Cited by 7
“Among the different biomaterials proposed for bone regeneration application, biodegradable polyesters have acquired a particular niche of interest, since they contain hydrolytically degradable bonds and the release of the degradation products which are normal intermediates of metabolic pathways (1-4).”
BackgroundThe influence of degradation on the viscosity and molecular mass of poly(lactide acid) biopolymer
Ekiert, M., Młyniec, A., & Uhl, T. (2017) · Diagnostyka · Cited by 8
Compostable Polymeric Ecomaterials: Environment-Friendly Waste Management Alternative to Landfills
Sikorska, W., Musioł, M., Zawidlak-Węgrzyńska, B., & Rydz, J. (2017) · Springer eBooks · doi:10.1007/978-3-319-48281-1_36-1 · Cited by 9
Gea, S., Surga, M., Rahayu, S., et al. (2018) · AIP conference proceedings · doi:10.1063/1.5082468 · Cited by 7
Aboudzadeh, N., Khavandi, A., Javadpour, J., Shokrgozar, M. A., & Imani, M. (2021) · Iranian Biomedical Journal · doi:10.52547/ibj.25.6.408 · Cited by 11
“These polyesters are also among the few FDA approved biodegradable polymers [12] .”
BackgroundChauhan, N., & Singh, Y. (2022) · Springer eBooks · doi:10.1007/978-981-16-3667-7_13 · Cited by 9
Magnago, R. F., de Aguiar, A. C., Valezan, I. F., de Moraes, F. M., Ziulkoski, A. L., Morisso, F. D. P., Κanis, L. A., & Zepon, Κ. M. (2022) · European Polymer Journal · doi:10.1016/j.eurpolymj.2022.111533 · Cited by 8
Rasitanon, N., Rattanapan, P., Kaewpradub, K., et al. (2023) · Biosensors · doi:10.3390/bios13080772 · Cited by 7
“While the majority of MPs are made from synthetic polymers (such as poly(glycolic acid), poly(lactic acid), poly(p-dioxanone), and copolymers of trimethylene carbonate and glycolide) [12], exploring the utilization of inexpensive biomaterials is crucial in expanding the possibilities for developing biocompatible MPs w…”
BackgroundBalaburov, E., Kamaraj, M., Doyle, S. E., Ahmadi, Z., Bella, C. D., Nisbet, D. R., Moulton, S. E., & Aguilar, L. M. C. (2023) · Journal of Applied Polymer Science · doi:10.1002/app.54759 · Cited by 8
Min, S. K., Jung, S.-M., Kim, S. H., Kim, C. R., & Shin, H. S. (2013) · Journal of Biomedical Materials Research Part B Applied Biomaterials · doi:10.1002/jbm.b.32939 · Cited by 8
Gromadzki, D., Rychter, P., Uchman, M., Momekova, D. B., Marcinkowski, A., Koseva, N. S., Fray, M. E., & Marić, M. (2015) · Macromolecular Chemistry and Physics · doi:10.1002/macp.201500235 · Cited by 7
Krikštanavičienė, K., Stanys, S., & Jonaitienė, V. (2014) · Autex Research Journal · doi:10.2478/aut-2014-0001 · Cited by 8
Wang, Y., Zhou, C., Meng, Y., et al. (2011) · Journal of Porous Materials · doi:10.1007/s10934-011-9457-x · Cited by 7
“Collagen has been extensively used for tissue engineering due to its non-toxic nature and biodegradability [28, 29] but its lower tensile strength character is undesirable for neural tissue engineering.”
BackgroundCurrent treatment methods for combination antiretroviral therapy-induced lipoatrophy of the face
Kadouch, J. A., van Rozelaar, L., Karim, R. B., & Hoekzema, R. (2013) · International Journal of STD & AIDS · doi:10.1177/0956462412474539 · Cited by 7
Structure/Property Relationships of Poly(L-lactic Acid)/Mesoporous Silica Nanocomposites
Rivera, J. G., Medellín‐Rodríguez, F. J., Ávila‐Orta, C. A., Palestino, G., & Sánchez‐Valdés, S. (2013) · Journal of Polymers · doi:10.1155/2013/162603 · Cited by 7
“Moreover, PLLA is used as scaffold for bone tissue regeneration [2–6].”
MethodThe Effects of Bioactive Nanoparticles on the Degradation of DLGA
Díaz, E., Puerto, I., & Sandonis, I. (2014) · International Journal of Polymeric Materials · doi:10.1080/00914037.2014.886242 · Cited by 8
Polymer Based Tissue Engineering Strategies for Neural Regeneration
Radhakrishnan, E. K. (2017) · Advances in Tissue Engineering & Regenerative Medicine Open Access · doi:10.15406/atroa.2017.02.00016 · Cited by 7
Andreasen, C. M., Ding, M. L., Andersen, T. L., & Overgaard, S. (2017) · Journal of Tissue Engineering and Regenerative Medicine · doi:10.1002/term.2447 · Cited by 7
“D,L‐lactic acid (PDLLA) is, due to its osteoconductive properties and high biocompatibility, one of the most common coating materials for tissue engineering applications (Gunatillake & Adhikari, 2003).”
BackgroundBurg, K. J. L., Inskeep, B., & Burg, T. C. (2013) · Elsevier eBooks · doi:10.1016/b978-0-12-398358-9.00036-7 · Cited by 7
Monteiro, N. O., & Yelick, P. C. (2018) · Elsevier eBooks · doi:10.1016/b978-0-12-809880-6.00051-5 · Cited by 12
Kruk, A., Gadomska‐Gajadhur, A., Rykaczewska, I., Dulnik, J., Ruśkowski, P., & Synoradzki, L. (2018) · Journal of Biomedical Materials Research Part B Applied Biomaterials · doi:10.1002/jbm.b.34200 · Cited by 7
Original implementation of low-temperature SPS for bioactive glass used as a bone biomaterial
Gharbi, A., Ayadi, S., Jouini, N., et al. (2021) · Journal of the mechanical behavior of biomedical materials/Journal of mechanical behavior of biomedical materials · doi:10.1016/j.jmbbm.2021.104988 · Cited by 7
Kim, D., Kim, W., Park, S., et al. (2019) · Macromolecular Research · doi:10.1007/s13233-020-8007-2 · Cited by 7
Jassal, M., Sengupta, S., Warner, S. B., et al. (2013) · Textile Research Journal · doi:10.1177/0040517513481870 · Cited by 7
“In tissue engineering, biodegradable polymer-based textile structures are becoming more popular as their specific chemical composition, mechanical properties, degradation properties, and morphological features can be controlled and modified according to the required application.(7) Nano-scaled materials offer various…”
BackgroundPhosphonoethylated Polyglycidols: A Platform for Tunable Enzymatic Grafting Density
Koehler, J., Marquardt, F., Keul, H., et al. (2013) · Macromolecules · doi:10.1021/ma400255n · Cited by 7
In Vitro Characterization of Cell–Biomaterials Interactions
Thasneem, Y. M., & Sharma, C. P. (2013) · Elsevier eBooks · doi:10.1016/b978-0-12-415800-9.00005-x · Cited by 13
Biomedical Polymer Composites and Applications
Mouzakis, D. E. (2013) · Polymer Composites · doi:10.1002/9783527674220.ch14 · Cited by 8
Khavandegar, A., Dehnavi, N. S., Ganau, M., Ramezani, Z., Khodadoust, E., Tabatabaei, M. S. H. Z., Maleki, T., Mousavi, M. A., RayatSanati, K., Esmaeili, M., et al. (2025) · Spinal Cord · doi:10.1038/s41393-025-01114-9 · Cited by 9
“Moreover, BDNF reduces in fl ammation and apoptosis at the injury site, creating a more conducive environment for neural repair [62 – 64].”
Xu, Y., Huang, Y., Armstrong, J. P. K., Xu, W., Biglino, G., Zhang, W., Qi, Q., Chen, X., Abram, S. G. F., Vyas, C., et al. (2026) · Materials Science and Engineering R Reports · doi:10.1016/j.mser.2026.101210 · Cited by 11
Landau, S., Kieda, J., Khosravi, R., Okhovatian, S., Ramsay, K., Liu, C., Shakeri, A., Zhao, Y., Shen, K., Bar‐Am, O., et al. (2024) · Bioactive Materials · doi:10.1016/j.bioactmat.2024.10.008 · Cited by 8
Kolpek, D., Kim, J., Mohammed, H., Gensel, J. C., & Park, J. (2024) · International Journal of Nanomedicine · doi:10.2147/ijn.s497859 · Cited by 12
“120,121 Among these, some polymeric materials have immunomodulatory effects, like the previously mentioned PLGA.”
Conductive biological materials for in vitro models: properties and sustainability implications
Serafin, A., Casanova, C. R., Chandel, A. K. S., Reis, R. L., Oliveira, J. M., & Collins, M. N. (2025) · In vitro models · doi:10.1007/s44164-025-00088-5 · Cited by 7
“This versatility and sustainability make PLA famous for producing scaffolds that support cell growth and tissue regeneration [46, 47].”
Boccafoschi, F., Fusaro, L., Botta, M., et al. (2014) · Biointerphases · doi:10.1116/1.4864432 · Cited by 6
Fabrication of Tissue Engineering Scaffold from Hydroxyapatite/Alginate Composite
Nazarpak, M. H., & Pourasgari, F. (2014) · International Journal of Bioscience Biochemistry and Bioinformatics · doi:10.7763/ijbbb.2014.v4.327 · Cited by 7
Injizierbare Füllmaterialien – Update und Zukunftsperspektive
Aitzetmüller, M. M., Sukhova, I., Huemer, G. M., Machens, H., Schantz, J., & Duscher, D. (2017) · Handchirurgie · Mikrochirurgie · Plastische Chirurgie · doi:10.1055/s-0043-112498 · Cited by 6
“PCL ist schon seit den 90er Jahren als bio-degradierbares Polymer bekannt und fand bisher für chirurgisches Nahtmaterial Verwendung [26].”
Tissue engineering of the kidney
Kim, J. H., Atala, A., & Yoo, J. J. (2020) · Elsevier eBooks · doi:10.1016/b978-0-12-818422-6.00047-2 · Cited by 6
Metadata
- Authors
- CSIRO Molecular Science, B. 1., & Gunatillake, P.
- Corresponding author
- CSIRO Molecular Science, Bag 10, Clayton South MDC, Vic 3169, Australia
- Venue
- European Cells and Materials
- Publisher
- Forum Multimedia Publishing LLC
- Published
- 2003-10-01
- Volume
- 5
- Pages
- 1-16
- ISSN
- 1473-2262 (ISSN-L)
- OpenAlex
- W2106035984
- Cited by
- 1,765
- References
- 97
- Citations by year
- 2026: 43 · 2025: 61 · 2024: 59 · 2023: 80 · 2022: 90 · 2021: 112 · 2020: 102 · 2019: 115 · 2018: 105 · 2017: 128 · 2016: 110 · 2015: 106 · 2014: 110 · 2013: 91 · 2012: 86
- FWCI
- 1.32
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- cc-by
- Locations
- European Cells and Materials (publishedVersion, cc-by)
- PubMed (publishedVersion)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion)
- Topics
- Physical Sciences › Materials Science › Biomaterials › biodegradable polymer synthesis and properties
- Physical Sciences › Engineering › Biomedical Engineering › Bone Tissue Engineering Materials
- Health Sciences › Medicine › Surgery › Surgical Sutures and Adhesives
- Keywords
- tissue engineering, polyesters, polyglycolic acid, polylactic acid, polyanhydrides, polyphosphazenes, polyurethane, poly(propylene fumarate), injectable polymers, orthopedic tissue engineering, biodegradation, biocompatibility, degradation products
- MeSH terms
- Biocompatible Materials, Models, Chemical, Polymers, Tissue Engineering
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.