Biodegradable synthetic polymers for tissue engineering
Open accessThe DOI matches its Crossref record; 96 of the 97 references it cites were found in a registry or an index; 1 of the 146 sources its claims cite were checked for support.
Abstract
This review focuses on biodegradable synthetic polymers, discussing synthesis, properties and biodegradability, especially within the polyester family including polylactides.
Overview
CoChat Summary
TL;DR
This review surveys biodegradable synthetic polymers for tissue engineering, emphasizing polyesters (PGA, PLA, PLGA), polylactones, poly(propylene fumarate), polyanhydrides, tyrosine-derived polycarbonates, polyorthoesters, polyurethanes, and polyphosphazenes. It concludes that polyesters dominate clinically, while injectable in situ curable systems such as PPF and photocrosslinkable polyanhydrides are promising but face challenges in biocompatibility, degradation control, and heat generation.
Key findings
- Polyesters are the most studied biodegradable polymers. PGA has 46–50% crystallinity, Tg 36°C, Tm 225°C; in Dexon sutures in vitro, first-stage degradation predominates for 21 days, crystalline degradation takes a further 28 days, and after 49 days weight loss was about 42% with complete loss of mechanical properties.
- PLA/PGA copolymer behavior depends on composition: 25–75% (l)LA/GA and 0–70% (dl)LA/GA are amorphous; 70/30 GA/LA has the highest water uptake, while 50/50 is reported as most unstable to hydrolysis; Vicryl is 8% (l)LA and 92% GA.
- Poly(caprolactone) degrades slowly: homopolymer degradation is on the order of 2–3 years, and PCL with initial average molecular weight 50,000 takes about 3 years for complete in vitro degradation.
- Poly(propylene fumarate) degrades to fumaric acid and propylene glycol; time to 20% original weight loss ranged from 84 days (PPF/β-TCP composite) to over 200 days (PPF/CaSO4 composite). PPF formulations showed maximum curing temperatures of 38–48°C versus 94°C for PMMA cements, curing times of 1–121 min, and compressive strengths of 1–12 MPa.
- Polyanhydrides degrade by surface erosion; poly(sebacic acid) degrades in about 54 days in saline, while poly(1,6-bis(p-carboxyphenoxy)hexane) is estimated at 1 year. Poly[1,6-bis(carboxyphenoxy)hexane] has a Young’s modulus of 1.3 MPa versus human bone at 40–60 MPa; poly(anhydride-co-imides) reached compressive strengths of 50–60 MPa, and photocrosslinked systems showed compressive strengths of 30–40 MPa and tensile strengths of 15–27 MPa.
- Degradable polyurethanes based on lysine diisocyanate showed varied properties: dl-lactide networks were rigid (Tg = 60°C) with ultimate tensile strengths of ~40–70 MPa, caprolactone triol networks were low-modulus elastomers with tensile strengths of 1–4 MPa, and copolymer networks had elongation up to 600% with compressive strengths of 3–25 MPa. In vivo, porous polyurethane artificial skin degraded almost completely 4–8 weeks after implantation in guinea pigs with no adverse tissue reaction.
Methods
- Design: narrative literature review; no primary experimental study or systematic review protocol is reported.
- Data/sample: published literature on biodegradable synthetic polymers, including synthesis, properties, degradation, biocompatibility, and injectable polymer systems; Tables 1–3 summarize polymer properties and precursors.
- Analysis: qualitative synthesis of major polymer classes, their degradation modes/products, mechanical properties, biocompatibility, and potential for injectable tissue-engineering compositions.
Limitations
- Stated: the paper notes that Table 2 data “should be used as a guide only” and that sufficient data are not available to provide a comprehensive list of properties for polyanhydrides, polycarbonates, polyurethanes, and polyphosphazenes.
- Stated: for polyanhydrides, no data are reported about polymer sterilizability and heat generation during polymerization; for degradable polyurethanes, the effect of degradation products and how they are removed from the body are not clearly understood.
- Evident: as a narrative review, it lacks systematic search criteria, study quality appraisal, and meta-analysis, so conclusions depend on the cited literature and may not comprehensively cover all biodegradable polymers or tissue-engineering applications.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
1 Valid · 20 Not valid · 105 Not checked · 89 Own results and interpretations
Every source the paper cites for this claim was checked and supports it.
In the paper
“A meniscal replica implanted contained only fibro-cartilage after 18 weeks and decreased the degradation of the articular cartilage.”
What the sources say
- Supportedcites De Groot et al.., 1996 source
The Aliphatic PU network passage (page not provided) reports that articular-cartilage degeneration was less severe with the prosthesis than in meniscectomized control knees. It also says the prostheses contained only fibrocartilage after 18 weeks. Degeneration was reduced, not eliminated. (LLM, conf=0.91)
plainstates a causeSingle case- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
In the paper
“The compressive strengths varied between 1 and 12 MPa”
What the sources say
- Not matchedcites Peter et al., 1998a
Couldn’t be matched to a paper in Crossref, so it can’t be checked.
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Not matched
In the paper
“Cross-linking characteristics reported for PPF, N-vinyl pyrrolidone (N-VP), benzoyl peroxide, sodium chloride, and TCP indicate that for a range of formulations, the maximum temperature varied within 38 to about 48ºC, compared to 94ºC observed for polymethylmethacrylate (PMMA) cements.”
What the sources say
- Not matchedcites Peter et al., 1998a
Couldn’t be matched to a paper in Crossref, so it can’t be checked.
hedged- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Not matched
None of the sources cited for this claim could be matched to a paper in Crossref, so there is nothing to check it against.
In the paper
“Based on in-vitro studies, the time required to reach 20% loss in original weight ranged from 84 (PPF/ß-TCP composite) to over 200 days (PPF/CaSO 4 composite)”
What the sources say
- Not matchedcites Peter et al., 1997b
Couldn’t be matched to a paper in Crossref, so it can’t be checked.
- Not matchedcites Kharas et al., 1997
Couldn’t be matched to a paper in Crossref, so it can’t be checked.
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Not matched
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“These composite materials exhibit compressive strengths in the range 2 to 30 MPa.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
94 more claims
Create a free account to see all 215 claims and to verify the 2 references still open.
- It may state two separate claims as one. 62
- Probably not a substantial claim. 76
- The quote only partly states this claim. 1
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“Advantages include a tightly controlled manufacturing process, accurate reproducibility, adjustable biodegradability, and a wide variety of both chemical and physical properties.[ 171 ]”
From Unraveling and Harnessing the Immune Response at the Cell–Biomaterial Interface for Tissue Engineering Purposes (2024) · cites this paper as [171]
Experimental — accuracy not yet measured
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
§ Polyanhydrides
“Polyanhydrides degrades by surface erosion (Kohn and Langer, 1997) and their main applications are in controlled drug delivery.”
§ Conclusions
“Polyanhydride degrade by bulk erosion and their main applications are in controlled drug delivery.”
Citations
Cites
Synthetic biodegradable polymers as orthopedic devices
Middleton, J. C., & Tipton, A. J. (2000) · Biomaterials · doi:10.1016/s0142-9612(00)00101-0 · Cited by 2,741 · cited 4×
“…developments in siloxane-based polyurethanes, which have greater in-vivo stability than conventional polyetherurethanes (e.g., poly(tetramethylene oxide) (PTMO)-based) have provided opportunities for development of a range of medical implants for chronic applications (Gunatillake et al., 2001).”
BackgroundInfluentialBiomaterial developments for bone tissue engineering
Burg, K. J. L., Porter, S., & Kellam, J. F. (2000) · Biomaterials · doi:10.1016/s0142-9612(00)00102-2 · Cited by 1,643 · cited 1×
“Polyesters have also been considered for development of tissue engineering applications (Hubbell, 1995; Thomson et al 1995a, Yazemski et al. 1996; Wong and Mooney, 1997), particularly for bone tissue engineering (Kohn and Langer, 1997; Burg et al., 2000).”
BackgroundChandra, R. (1998) · Progress in Polymer Science · doi:10.1016/s0079-6700(97)00039-7 · Cited by 1,462
Biodegradable polymers for use in surgery—polyglycolic/poly(actic acid) homo- and copolymers: 1
Gilding, D. K., & Reed, A. M. (1979) · Polymer · doi:10.1016/0032-3861(79)90009-0 · Cited by 1,345
Biomaterials in Tissue Engineering
Hubbell, J. A. (1995) · Nature Biotechnology · doi:10.1038/nbt0695-565 · Cited by 1,060 · cited 1×
“Polyesters have also been considered for development of tissue engineering applications (Hubbell, 1995; Thomson et al 1995a, Yazemski et al. 1996; Wong and Mooney, 1997), particularly for bone tissue engineering (Kohn and Langer, 1997; Burg et al., 2000).”
BackgroundPolylactic Acid for Surgical Implants
KULKARNI, R. K. (1966) · Archives of Surgery · doi:10.1001/archsurg.1966.01330050143023 · Cited by 841
Evolution of bone transplantation: molecular, cellular and tissue strategies to engineer human bone
Yaszemski, M. J., Payne, R. G., Hayes, W. C., Langer, R., & Mikos, A. G. (1996) · Biomaterials · doi:10.1016/0142-9612(96)85762-0 · Cited by 729
Miller, R. A., Brady, J. M., & Cutright, D. E. (1977) · Journal of Biomedical Materials Research · doi:10.1002/jbm.820110507 · Cited by 722 · cited 2×
“For the (l)LA/GA copolymers, resistance to hydrolysis is more pronounced at either end of the copolymers compositions range (Miller et al., 1977; Gilding and Reed, 1979; Reed and Gilding, 1981; Vert et al., 1984).”
BackgroundInjectable biodegradable materials for orthopedic tissue engineering
Temenoff, J. S., & Mikos, A. G. (2000) · Biomaterials · doi:10.1016/s0142-9612(00)00108-3 · Cited by 554 · cited 8×
“A number of methods have been reported to prepare PPF, and each results in different polymer properties (Peter et al., 1997a,b, 1999; Temenoff and Mikos 2000).”
BackgroundMethodInfluentialLeong, K. W., Brott, B. C., & Langer, R. (1985) · Journal of Biomedical Materials Research · doi:10.1002/jbm.820190806 · Cited by 541 · cited 12×
“The polyurethanes ranged from elastomers with elongations at break as high as 780 %, but with low tensile strengths (5.8 to 8.1 MPa).”
BackgroundInfluential
Research works printed but not linked: 5
- Scranton A, Bowman C, Peiffer R, eds. ACS Symposium Series 673; American Chemical Society, Washington DC. pp 189-202.
- Ratner BD, Hoffman AS, Schoen FJ, Lemon JE, eds. Aca- demic Press, San Diego. pp 65-73.
- Lamba NMK, Woodhouse KA, Cooper SL (1998) Poly- urethanes in Biomedical Applications. CRC Press: New York p 205-241.
- Mark JE, Alcock HR, West R (1992) Inorganic Poly- mers. Prentice Hall, Upper Saddle River, NJ. Chapter
- Ng SY, Vandamme T, Tayler MS, Heller J (1997) Syn- thesis and erosion studies of self-catalysed poly(orthoester)s. Macromolecules 30: 770-772.
Cited by
Items 901–1,000 of 1,762
Effects of yarn types and fabric types on the compliance and bursting strength of vascular grafts
Lou, C.-W., Lu, P.-C., Hu, J. J., & Lin, J. (2016) · Journal of the mechanical behavior of biomedical materials/Journal of mechanical behavior of biomedical materials · doi:10.1016/j.jmbbm.2016.03.002 · Cited by 16
Guided differentiation and tissue regeneration of induced pluripotent stem cells using biomaterials
Kuo, Y., & Rajesh, R. (2017) · Journal of the Taiwan Institute of Chemical Engineers · doi:10.1016/j.jtice.2017.04.043 · Cited by 16
Biodegradable Polymeric Materials for Medicinal Applications
Daniel, S. (2021) · Materials horizons · doi:10.1007/978-981-15-9643-8_13 · Cited by 22
Microfluidic Etching and Oxime-Based Tailoring of Biodegradable Polyketoesters
Barrett, D. G., Lamb, B. M., & Yousaf, M. N. (2008) · Langmuir · doi:10.1021/la801715w · Cited by 16
Salgado, A. J., Wang, Y., Mano, J. F., & Reis, R. L. (2006) · Materials science forum · doi:10.4028/www.scientific.net/msf.514-516.1020 · Cited by 16
Rymuszka, A., & Górczyńska, W. (2026) · Molecules · doi:10.3390/molecules31020333 · Cited by 21
“Lactic acid-derived materials are also used to fabricate biodegradable scaffolds for tissue engineering, supporting bone, muscle and skin regeneration [7,47,167].”
Wu, W., Zhou, Z., Liu, W., et al. (2019) · Journal of Macromolecular Science Part B · doi:10.1080/00222348.2019.1601809 · Cited by 15
Bile duct reconstruction using scaffold-free tubular constructs created by Bio-3D printer
Hamada, T., Nakamura, A., Soyama, A., Sakai, Y., Miyoshi, T., Yamaguchi, S., Hidaka, M., Hara, T., Kugiyama, T., Takatsuki, M., et al. (2021) · Regenerative Therapy · doi:10.1016/j.reth.2021.02.001 · Cited by 15
“Scaffolds comprise a variety of biocompatible materials, including animal-derived collagen [40] and synthetic polymers [41].”
BackgroundCHEN, C., Chen, S.-M., Lin, S., Liang, H., & Wu, C. (2021) · Polymers · doi:10.3390/polym13152552 · Cited by 19
“Synthetic and biodegradable polymers with tunable properties used as bone scaffolds have been reported to raise the risk of immunogenicity and toxicity [4,5].”
BackgroundLiu, R., Li, H., Liu, M., et al. (2022) · Chinese Chemical Letters · doi:10.1016/j.cclet.2022.05.089 · Cited by 15
Fabrication and Bioactivity of Peptide‐Conjugated Biomaterial Tissue Engineering Constructs
Nun, N., & Joy, A. (2022) · Macromolecular Rapid Communications · doi:10.1002/marc.202200342 · Cited by 17
Kerignard, E., Béthry, A., Falcoz, C., et al. (2022) · Pharmaceutics · doi:10.3390/pharmaceutics14091854 · Cited by 15
Gojżewski, H., van Drongelen, M., Imre, B., Hempenius, M. A., Check, C., Chartoff, R. P., Wurm, F. R., & Vancso, G. J. (2023) · Polymer Testing · doi:10.1016/j.polymertesting.2023.107961 · Cited by 15
Development of poly(n-alkylene oxalate)s toward a new kind of seawater degradable plastics
Tu, Z., Lu, Y., Zhang, Y., Li, Y., & Wei, Z. (2023) · Materials Today Sustainability · doi:10.1016/j.mtsust.2023.100378 · Cited by 25
Composite Hydrogels with Included Solid-State Nanoparticles Bearing Anticancer Chemotherapeutics
Zhivkov, A. M., Popov, T. T., & Hristova, S. H. (2023) · Gels · doi:10.3390/gels9050421 · Cited by 16
“Such polymers are dextran (DEX), poly(ethylene glycol) (PEG), poly(ethylene oxide) (PEO), polyvinyl alcohol (PVA), etc. [90,91]; (b) Hydrolysis .”
Advances in tissue engineering and biofabrication for in vitro skin modeling
Wistner, S. C., Rashad, L., & Slaughter, G. E. (2023) · Bioprinting · doi:10.1016/j.bprint.2023.e00306 · Cited by 20
Yildirim-Semerci, Ö., Bilginer-Kartal, R., & Yıldız, A. A. (2024) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2024.131856 · Cited by 18
Shlomo-Avitan, B., Machour, M., Ahmad, S., Friedler, Y., Levenberg, S., & Silverstein, M. S. (2024) · Polymer · doi:10.1016/j.polymer.2024.127971 · Cited by 15
Sgarioto, M., Adhikari, R., Gunatillake, P. A., Moore, T., Patterson, J., Nagel, M. D., & Malherbe, F. (2015) · Frontiers in Bioengineering and Biotechnology · doi:10.3389/fbioe.2015.00052 · Cited by 17
“A good understanding of the biocompatibility of materials and toxicity of compounds generated during degradation is essential before considering any new material for biomedical applications (Gunatillake and Adhikari, 2003; Williams, 2008).”
BackgroundSelf-citationYu, Y., Fan, C.-L., Hsu, Y., Chou, Y., Ueng, S. W., & Liu, S. (2015) · Materials · doi:10.3390/ma8115415 · Cited by 16
“In contrast, PCL only begins to degrade at least 24 months after implantation in vivo [15,16], and its mechanical strength can be maintained for up to 33 weeks [17].”
BackgroundLimongi, T., Lizzul, L., Giugni, A., Tirinato, L., Pagliari, F., Tan, H., Das, G., Moretti, M., Marini, M., Brusatin, G., et al. (2016) · Microelectronic Engineering · doi:10.1016/j.mee.2016.12.014 · Cited by 15
Stynes, G. D., Gengenbach, T. R., Kiroff, G., Morrison, W. A., & Kirkland, M. A. (2017) · Journal of Biomedical Materials Research Part A · doi:10.1002/jbm.a.36064 · Cited by 15
Tamjid, E. (2018) · International Journal of Polymeric Materials · doi:10.1080/00914037.2017.1417285 · Cited by 17
Ayyoob, M., Yang, X. M., Park, H.-J., Park, S., Kim, J., Nam, S. W., & Kim, Y. J. (2019) · Fibers and Polymers · doi:10.1007/s12221-019-1143-7 · Cited by 15
Enzymes and their production strategies
Sharma, H., & Upadhyay, S. K. (2020) · Elsevier eBooks · doi:10.1016/b978-0-12-819820-9.00003-x · Cited by 18
Current research on the blends of chitosan as new biomaterials
Rajeswari, A., Gopi, S., Christy, E. J. S., Jayaraj, K., & Pius, A. (2020) · Elsevier eBooks · doi:10.1016/b978-0-12-817970-3.00009-2 · Cited by 19
Steroid Eluting Esophageal-Targeted Drug Delivery Devices for Treatment of Eosinophilic Esophagitis
Prasher, A., Shrivastava, R., Dahl, D. K., Sharma-Huynh, P., Maturavongsadit, P., Pridgen, T. A., Schorzman, A. N., Zamboni, W. C., Ban, J., Blikslager, A. T., et al. (2021) · Polymers · doi:10.3390/polym13040557 · Cited by 20
“For photopolymerization-based 3D printing, a light reactive diluent is usually added to reduce the viscosity of the resin [59,62].”
Leveraging Potential of Nanotherapeutics in Management of Diabetic Foot Ulcer
Pandey, S., Shaif, M., Ansari, T. M., Shamim, A., & Kushwaha, P. (2022) · Experimental and Clinical Endocrinology & Diabetes · doi:10.1055/a-1749-4909 · Cited by 15
“Clinical trials have shown that recombinant human-platelet-derived growth factor, the only FDA-approved growth factor available for clinical use, increases the likelihood of wound closure and decreases the time to heal the wound completely [65].”
BackgroundInfluentialOsman, M. A., Virgilio, N., Rouabhia, M., & Mighri, F. (2022) · Polymers · doi:10.3390/polym14235079 · Cited by 16
Progress in Functionalized Biodegradable Polyesters
Heiny, M., Wurth, J. J., & Shastri, V. P. (2014) · Elsevier eBooks · doi:10.1016/b978-0-12-396983-5.00009-0 · Cited by 15
Jiang, T., Zhang, G., He, W., Li, H., & Jin, X. (2014) · Journal of Nanomaterials · doi:10.1155/2014/837695 · Cited by 15
“The homopolymer PCL has a total degradation of 2∼4 years (depending of the starting molecular weight of the device or implant) [13, 14].”
BackgroundBone tissue engineering and biomineralization
Silvio, L. D. (2007) · Elsevier eBooks · doi:10.1533/9781845693817.2.319 · Cited by 15
Bioreactors for Tissue Engineering Purposes
Blose, K. J., Krawiec, J. T., Weinbaum, J. S., & Vorp, D. A. (2013) · Elsevier eBooks · doi:10.1016/b978-0-12-398523-1.00013-6 · Cited by 17
Synthesis and characterisation of fluorescent pyrene‐end‐capped polylactide fibres
Alwattar, A. A., Haddad, A. M., Zhou, Q., Nascimento, T. R. D. L., Greenhalgh, R. D., Medeiros, E. S. D., Blaker, J. J., Parry, A. V. S., Quayle, P., & Yeates, S. G. (2018) · Polymer International · doi:10.1002/pi.5712 · Cited by 15
Mendibil, X., Ortiz, R., de Viteri, V. S., Ugartemendia, J. M., Sarasua, J.-R., & Quintana, I. (2019) · Polymers · doi:10.3390/polym12010034 · Cited by 20
Kühl, S., Deniz, A., Gau, E., et al. (2020) · Polymer · doi:10.1016/j.polymer.2020.122314 · Cited by 15
Surface tension of poly(ester urethane)s and poly(ether urethane)s
Lupu, M., Macocinschi, D., Ioanid, G. E., Butnaru, M., & Ioan, S. (2006) · Polymer International · doi:10.1002/pi.2163 · Cited by 15
Naureen, B., Ang, B. C., Muhamad, F., Haseeb, A. S. M. A., & Basirun, W. J. (2025) · Polymer Engineering and Science · doi:10.1002/pen.27090 · Cited by 16
“22 24 Moreover, the diverse properties of PU that are beneficial for TE scaffolds include biocompatibility, biodegradability, 12,25,26 modifiable porosity, 27 appropriate mechanical strength, 28 and suitability for cell growth and proliferation.”
A Review on the properties and applications of biodegradable polymers
Patwary, M. A. S., Maraz, K. M., Shahida, S., Ahmed, A., & Khan, R. A. (2021) · GSC Advanced Research and Reviews · doi:10.30574/gscarr.2021.9.1.0218 · Cited by 17
“Polyanhydrides show hydrolytic instability thus they should be stored under moisture-free frozen conditions and low mechanical strength [62-68].”
BackgroundBorah, A., & Kumar, D. S. (2022) · Elsevier eBooks · doi:10.1016/b978-0-12-823966-7.00003-7 · Cited by 21
Ahlfeld, T., Lode, A., Placht, A.-M., Fecht, T., Wolfram, T., Grom, S., Hoess, A., Vater, C., Bräuer, C., Heinemann, S., et al. (2023) · Biomaterials Science · doi:10.1039/d2bm02071h · Cited by 17
Optimizing PCL/PLGA Scaffold Biocompatibility Using Gelatin from Bovine, Porcine, and Fish Origin
Azar, M. G., Wiesnerová, L., Dvořáková, J., Chocholata, P. K., Moztarzadeh, O., Dejmek, J., & Babuška, V. (2023) · Gels · doi:10.3390/gels9110900 · Cited by 16
“Glycolic acid, on the other hand, is primarily excreted through urine after undergoing oxidative metabolism in the liver [24,25].”
BackgroundMehtiö, T., Nurmi, L., Rämö, V., Harlin, A., & Ropponen, J. (2012) · European Polymer Journal · doi:10.1016/j.eurpolymj.2012.01.010 · Cited by 15
Puricelli, E., Corsetti, A., Ponzoni, D., et al. (2010) · Head & Face Medicine · doi:10.1186/1746-160x-6-10 · Cited by 14
“Gunatillake PA, Adhikari R: Biodegradable synthetic polymers for tissue engineering.”
BackgroundElectrospinning of Gelatin Nanofibre: Current Trends in Tissue Engineering Applications
Nuge, M. E. H. T. (2013) · Journal of Applied Mechanical Engineering · doi:10.4172/2168-9873.1000e122 · Cited by 13
“In biomedical applications, synthetic biodegradable polymers such as polyester regularly associated with poor biocompatibility and systemic or local reaction resulted from the acidic degradation products [1].”
BackgroundAkram, M. A., Wang, L., Yu, H., Khalid, H., Abbasi, N. M., Ul-Abdin, Z., Chen, Y., Sun, R., Shan, J., & Saleem, M. (2016) · International Journal of Polymeric Materials · doi:10.1080/00914037.2016.1149847 · Cited by 14
Determinants of preferential renal accumulation of synthetic polymers in acute kidney injury
Chen, Y., Tang, W., Yu, F., Xie, Y., Jaramillo, L., Jang, H., Li, J., Padanilam, B. J., & Oupický, D. (2019) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2019.118555 · Cited by 17
“Synthetic polymers have been used as carriers to target proximal tubular cells by means of either physically encapsulating or covalently conjugating drugs (Duncan and Kopeček, 1984; Gunatillake and Adhikari, 2003; Li et al., 2015).”
BackgroundEl‐Bakary, M. A., El-Farahaty, K. A., & El‐Sayed, N. M. (2019) · Materials Research Express · doi:10.1088/2053-1591/ab4307 · Cited by 14
The Role of Neural Tissue Engineering in the Repair of Nerve Lesions
Abdolmaleki, A., Asadi, A., Momen, L. T., & Pilerood, S. P. (2020) · The Neuroscience Journal of Shefaye Khatam · doi:10.29252/shefa.8.3.80 · Cited by 14
Cradle-to-cradle: designing biomaterials to fit as truly biomimetic cell scaffolds– a review
Üstünel, Ş., Prévôt, M. E., Clements, R. J., & Hegmann, E. (2020) · Liquid Crystals Today · doi:10.1080/1358314x.2020.1855919 · Cited by 17
Controlled degradation of polycaprolactone-based micropillar arrays
Geoghegan, N., O′Loughlin, M., Delaney, C., Rochfort, K. D., Kennedy, M., Kolagatla, S., Podhorska, L., Rodriguez, B. J., Florea, L., & Kelleher, S. M. (2023) · Biomaterials Science · doi:10.1039/d3bm00165b · Cited by 14
Bone regeneration by biodegradable polymers
Basanth, A., Mayilswamy, N., & Kandasubramanian, B. (2022) · Polymer-Plastics Technology and Materials · doi:10.1080/25740881.2022.2029886 · Cited by 16
“Thus, the material’s ability to be arranged into usual patterns is an important element in this process .([64,65])”
BackgroundPolymer Chemistry and Synthetic Polymers
Parisi, O. I., Curcio, M., & Puoci, F. (2014) · Springer eBooks · doi:10.1007/978-3-319-12478-0_1 · Cited by 20
“Biodegradable synthetic polymers find their biomedical applications mostly in tissue engineering, to provide temporary structure support, regenerative medicine, or in controlled gene and drug delivery [24].”
BackgroundLiu, X., Hasan, M. S., Grant, D. M., Harper, L. T., Parsons, A. J., Palmer, G., Rudd, C. D., & Ahmed, I. (2014) · Journal of Biomaterials Applications · doi:10.1177/0885328214541302 · Cited by 16
Kitahara, M., Miyagawa, S., Fukushima, S., Saito, A., Shintani, A., Akita, T., & Sawa, Y. (2017) · Seminars in Thoracic and Cardiovascular Surgery · doi:10.1053/j.semtcvs.2017.01.016 · Cited by 19
Mano, S. S., Uto, K., & Ebara, M. (2017) · Theranostics · doi:10.7150/thno.20582 · Cited by 15
“Furthermore, natural [24] and synthetic polymer-based scaffold materials [25] that modulate cellular behaviors are tremendously attractive in the biomedical area.”
BackgroundLi, J., Zhao, X., Ye, L., Coates, P. D., & Caton‐Rose, F. (2019) · Journal of Biomedical Materials Research Part A · doi:10.1002/jbm.a.36604 · Cited by 15
Optimization of Biodegradable PLA/PCL Microspheres Preparation as Controlled Drug Delivery Carrier
Hakim, S. L., Kusumasari, F. C., & Budianto, E. (2020) · Materials Today Proceedings · doi:10.1016/j.matpr.2019.08.156 · Cited by 14
Sathish, P. B., Narmadha, R., & Selvakumar, R. (2020) · Materials Letters · doi:10.1016/j.matlet.2020.129038 · Cited by 15
Gwon, Y., Park, S., Kim, W., Han, T., Kim, H., & Kim, J. (2021) · Journal of Biological Engineering · doi:10.1186/s13036-021-00263-8 · Cited by 15
Natural and Synthetic Polymeric Scaffolds
Yoon, D. M., & Fisher, J. P. (2020) · Springer eBooks · doi:10.1007/978-3-030-49206-9_6 · Cited by 15
Types of bioresorbable polymers for medical applications
Casalini, T., & Perale, G. (2012) · Elsevier eBooks · doi:10.1533/9780857096517.1.3 · Cited by 16
Modification and characteristics of biodegradable polymer suitable for selective laser sintering
Lee, P.-H., Chang, E. C., Yu, S., et al. (2013) · International Journal of Precision Engineering and Manufacturing · doi:10.1007/s12541-013-0145-4 · Cited by 14
“During the healing processes, scaffolds are hydrolyzed and finally disappear completely from human body.(1-4) For the increased needs of biodegradable polymer scaffolds, various researchers have undertaken extensive researches on manufacturing processes.”
Coimbra, M. E. R., Elias, C. N., & Coelho, P. G. (2008) · Journal of Materials Science Materials in Medicine · doi:10.1007/s10856-008-3425-2 · Cited by 19
In vivo analysis of covering materials composed of biodegradable polymers enriched with flax fibers
Gredes, T., Schönitz, S., Gedrange, T., Stepien, L., Kozak, K., & Kunert‐Keil, C. (2017) · Biomaterials Research · doi:10.1186/s40824-017-0094-6 · Cited by 16
“PLA degrades inter alia, to lactic acid, which is further metabolized either in the citric acid cycle or excreted through the kidneys [55].”
BackgroundEngineered natural and synthetic polymer surfaces induce nuclear deformation in osteosarcoma cells
Antmen, E., Ermis, M., Demirci, U., & Hasırcı, V. (2018) · Journal of Biomedical Materials Research Part B Applied Biomaterials · doi:10.1002/jbm.b.34128 · Cited by 14
Bone Tissue Engineering: From Biomaterials to Clinical Trials
Jagadale, S., Damle, M. N., & Joshi, M. G. (2025) · Advances in experimental medicine and biology · doi:10.1007/5584_2024_841 · Cited by 19
Omar, R., Yang, J., Huynh, T., Gulia, K., Tavolacci, S. C., Wu, W., Wang, Y., & Haick, H. (2025) · Advanced Materials Technologies · doi:10.1002/admt.202501020 · Cited by 21
Insights into the Degradation of Polymer–Drug Conjugates by an Overexpressed Enzyme in Cancer Cells
Figueiredo, P., González, R., & Carvalho, A. T. P. (2023) · Journal of Medicinal Chemistry · doi:10.1021/acs.jmedchem.2c01781 · Cited by 13
Vijayaraghavan, R., Vidyavathi, M., Kumar, R. V. S., Loganathan, S., & Valapa, R. B. (2025) · Biomaterials Science · doi:10.1039/d4bm01550a · Cited by 13
Potnis, P. A., Tesfamariam, B., & Wood, S. C. (2011) · Journal of Cardiovascular Pharmacology · doi:10.1097/fjc.0b013e31821a4f1e · Cited by 13
“The ability to tailor degradation kinetics and the limited polymeric foreign body–associated adverse effects are the advantages that biodegradable polymers offer over other synthetic nonbiodegradable polymer materials.(6) To date, several different biodegradable polymers have been proposed as potential candidate mater…”
BackgroundInfluentialNanoengineered biomaterials for bone/dental regeneration
Kargozar, S., Milan, P. B., Baino, F., & Mozafari, M. (2018) · Elsevier eBooks · doi:10.1016/b978-0-12-813355-2.00002-8 · Cited by 21
Electrical and Optical Properties of Silicon Oxide Lignin Polylactide (SiO2-L-PLA)
Fal, J., Bulanda, K., Traciak, J., Sobczak, J., Kuzioła, R., Grąz, K., Budzik, G., Oleksy, M., & Żyła, G. (2020) · Molecules · doi:10.3390/molecules25061354 · Cited by 17
“PLA is used in orthopedics when high mechanical strength and ductility are required [12].”
MethodInkjet Printing of Nanohydroxyapatite Gradients on Fibrous Scaffold for Bone–Ligament Enthesis
Uehlin, A. F., Vines, J. B., Feldman, D. S., Dean, D. R., & Thomas, V. (2022) · JOM · doi:10.1007/s11837-022-05397-8 · Cited by 15
Synthesis of novel polyesters for potential applications in skin tissue engineering
Kanitkar, A., Smoak, M. M., Chen, C., Aita, G. M., Scherr, T., Madsen, L. R., & Hayes, D. J. (2015) · Journal of Chemical Technology & Biotechnology · doi:10.1002/jctb.4638 · Cited by 12
From Flab to Fab: Transforming Surgical Waste into an Effective Bioactive Coating Material
Luo, B., Yuan, S., Foo, S. E. M., Wong, M. T. C., Lim, T. C., Tan, N. S., & Choong, C. S. N. (2014) · Advanced Healthcare Materials · doi:10.1002/adhm.201400514 · Cited by 13
Keim, T., & Gall, K. (2009) · Journal of Biomedical Materials Research Part A · doi:10.1002/jbm.a.32195 · Cited by 17
Surface and mechanical properties of some new biopolyurethane composites
Macocinschi, D., Filip, D., & Vlad, S. (2010) · Polymer Composites · doi:10.1002/pc.20994 · Cited by 15
Biodegradable Polymers for Focal Delivery Systems
Khan, W., Challa, V. G. S., Langer, R., & Domb, A. J. (2013) · Advances in delivery science and technology · doi:10.1007/978-1-4614-9434-8_1 · Cited by 13
Biomaterials and 3D Printing Techniques for Neural Tissue Regeneration
Lee, S., Zhu, W., Castro, N. J., & Zhang, L. G. (2016) · Springer eBooks · doi:10.1007/978-3-319-31433-4_1 · Cited by 16
Degradable poly(ester amide)s from olive oil for biomedical applications
Nilawar, S., Dasgupta, Q., Madras, G., & Chatterjee, K. (2019) · Emergent Materials · doi:10.1007/s42247-019-00032-w · Cited by 12
Cao, K., Flegg, D. S., Lin, S., Lagugné‐Labarthet, F., Mequanint, K., & Gillies, E. R. (2019) · ACS Applied Polymer Materials · doi:10.1021/acsapm.9b00475 · Cited by 13
Sumathy, B., & Nair, P. D. (2020) · Journal of Biomaterials Science Polymer Edition · doi:10.1080/09205063.2020.1725861 · Cited by 13
Piotrowski, M., Jantas, D., Szczepanowicz, K., Łukasiewicz, S., Lasoń, W., & Warszyński, P. (2015) · Colloids and Surfaces B Biointerfaces · doi:10.1016/j.colsurfb.2015.07.029 · Cited by 13
Adhesion and proliferation of human bladder RT112 cells on functionalized polyesters
Renard, E., Vergnol, G., & Langlois, V. (2011) · IRBM · doi:10.1016/j.irbm.2010.12.001 · Cited by 17
Biomedical Applications for Thermoplastic Starch
Carvalho, A. J. F., & Trovatti, E. (2016) · doi:10.1002/9781119117360.ch1 · Cited by 13
Biofunctionalization of Stem Cell Scaffold for Osteogenesis and Bone Regeneration
Chen, Q., Jiang, Y., Zhang, X., Xu, S.-C., Wang, Y., Xing, D., & Li, H. (2025) · Biomolecules · doi:10.3390/biom15121700 · Cited by 13
Effect of Uniaxial Compression Frequency on Osteogenic Cell Responses in Dynamic 3D Cultures
Kontogianni, G., Loukelis, K., Bonatti, A. F., Batoni, E., Maria, C. D., Naseem, R., Dalgarno, K. W., Vozzi, G., MacManus, D. B., Mondal, S. K., et al. (2023) · Bioengineering · doi:10.3390/bioengineering10050532 · Cited by 12
“Such constructs can comprise, among others, biodegradable synthetic polymers, such as poly (lactic acid) (PLA) [10], poly(ε-caprolactone) (PCL) [11], poly(methyl methacrylate) (PMMA) [12], poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV), or their combinations [13].”
BackgroundČajková, J., Trebuňová, M., Modrák, M., Ižaríková, G., Bačenková, D., Balint, T., & Živčák, J. (2024) · Polymers · doi:10.3390/polym16212969 · Cited by 14
“Scaffolds must degrade at a rate that matches tissue formation, ensuring sufficient mechanical support while allowing natural bone to regenerate [16,17].”
BackgroundAlkhamis, H., Saretia, S., Schwanz, S., Machatschek, R., Neffe, A. T., & Polak-Kraśna, K. (2025) · Polymer Degradation and Stability · doi:10.1016/j.polymdegradstab.2025.111267 · Cited by 12
Advancements in Biodegradable Orthopaedic Implants: A Literature Review
Kotteda, A. K., Saikumar, T., & Shreegan, A. A. (2025) · Indian Journal of Orthopaedics · doi:10.1007/s43465-025-01445-y · Cited by 12
“Polymers such as PLA and PLGA may not be suitable for high-load applications, often restricting them to small fracture fixation devices or soft tissue reconstructions [63].”
Fabrication of biodegradable polyurethane microspheres by a facile and green process
Lin, C.-Y., & Hsu, S. (2014) · Journal of Biomedical Materials Research Part B Applied Biomaterials · doi:10.1002/jbm.b.33266 · Cited by 12
Is regenerative medicine a new hope for kidney replacement?
Nowacki, M. S., Kloskowski, T., Pokrywczyńska, M., Nazarewski, Ł., Jundziłł, A., Pietkun, K., Tyloch, D. J., Rasmus, M., Warda, K., Habib, S. L., et al. (2014) · Journal of Artificial Organs · doi:10.1007/s10047-014-0767-z · Cited by 12
Bagheri, M., Pourmoazzen, Z., & Entezami, A. A. (2013) · Iranian Polymer Journal · doi:10.1007/s13726-013-0129-3 · Cited by 12
“Natural monomers have been used extensively in recent years in chemical engineering, medicine/pharmaceuticals, food and agriculture because of their low cost, free availability, non-toxicity and biodegradability characteristics [1, 2].”
BackgroundNatarajan, J., Madras, G., & Chatterjee, K. (2016) · RSC Advances · doi:10.1039/c6ra02058e · Cited by 12
Stem Cells, Bioengineering, and 3-D Scaffolds for Nervous System Repair and Regeneration
Sandquist, E. J., Uz, M., Sharma, A. D., Patel, B. B., Mallapragada, S. K., & Sakaguchi, D. S. (2016) · Springer eBooks · doi:10.1007/978-3-319-31433-4_2 · Cited by 14
Preparation of biodegradable semi-permeable membranes as 3D scaffolds for cell cultures
Kruk, A., Gadomska‐Gajadhur, A., Ruśkowski, P., Chwojnowski, A., Dulnik, J., & Synoradzki, L. (2017) · Desalination and Water Treatment · doi:10.5004/dwt.2017.11415 · Cited by 13
Preparation and properties of BMPLGA/NBAG-β-TCP composite scaffold materials
Wu, W., Fang, J., Liu, W., Zhao, Y., Huang, T., Zhao, Y., Li, X., Cui, J., Yang, Y., & Zhou, Z. (2018) · International Journal of Polymer Analysis and Characterization · doi:10.1080/1023666x.2018.1499275 · Cited by 12
Drug-releasing Biopolymeric Structures Manufactured via Stereolithography
Asikainen, S., van Bochove, B., & Seppälä, J. V. (2019) · Aaltodoc (Aalto University) · doi:10.1088/2057-1976/aaf0e · Cited by 12
MSC differentiation on two-photon polymerized, stiffness and BMP2 modified biological copolymers
Böhrnsen, F., Krier, M., Grohmann, S., Hauptmann, N., Frant, M., Klaus, L., & Schliephake, H. (2019) · Biomedical Materials · doi:10.1088/1748-605x/ab0362 · Cited by 12
Metadata
- Authors
- CSIRO Molecular Science, B. 1., & Gunatillake, P.
- Corresponding author
- CSIRO Molecular Science, Bag 10, Clayton South MDC, Vic 3169, Australia
- Venue
- European Cells and Materials
- Publisher
- Forum Multimedia Publishing LLC
- Published
- 2003-10-01
- Volume
- 5
- Pages
- 1-16
- ISSN
- 1473-2262 (ISSN-L)
- OpenAlex
- W2106035984
- Cited by
- 1,765
- References
- 97
- Citations by year
- 2026: 43 · 2025: 61 · 2024: 59 · 2023: 80 · 2022: 90 · 2021: 112 · 2020: 102 · 2019: 115 · 2018: 105 · 2017: 128 · 2016: 110 · 2015: 106 · 2014: 110 · 2013: 91 · 2012: 86
- FWCI
- 1.32
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- cc-by
- Locations
- European Cells and Materials (publishedVersion, cc-by)
- PubMed (publishedVersion)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion)
- Topics
- Physical Sciences › Materials Science › Biomaterials › biodegradable polymer synthesis and properties
- Physical Sciences › Engineering › Biomedical Engineering › Bone Tissue Engineering Materials
- Health Sciences › Medicine › Surgery › Surgical Sutures and Adhesives
- Keywords
- tissue engineering, polyesters, polyglycolic acid, polylactic acid, polyanhydrides, polyphosphazenes, polyurethane, poly(propylene fumarate), injectable polymers, orthopedic tissue engineering, biodegradation, biocompatibility, degradation products
- MeSH terms
- Biocompatible Materials, Models, Chemical, Polymers, Tissue Engineering
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.