Biodegradable synthetic polymers for tissue engineering
Open accessThe DOI matches its Crossref record; 96 of the 97 references it cites were found in a registry or an index; 1 of the 146 sources its claims cite were checked for support.
Abstract
This review focuses on biodegradable synthetic polymers, discussing synthesis, properties and biodegradability, especially within the polyester family including polylactides.
Overview
CoChat Summary
TL;DR
This review surveys biodegradable synthetic polymers for tissue engineering, emphasizing polyesters (PGA, PLA, PLGA), polylactones, poly(propylene fumarate), polyanhydrides, tyrosine-derived polycarbonates, polyorthoesters, polyurethanes, and polyphosphazenes. It concludes that polyesters dominate clinically, while injectable in situ curable systems such as PPF and photocrosslinkable polyanhydrides are promising but face challenges in biocompatibility, degradation control, and heat generation.
Key findings
- Polyesters are the most studied biodegradable polymers. PGA has 46–50% crystallinity, Tg 36°C, Tm 225°C; in Dexon sutures in vitro, first-stage degradation predominates for 21 days, crystalline degradation takes a further 28 days, and after 49 days weight loss was about 42% with complete loss of mechanical properties.
- PLA/PGA copolymer behavior depends on composition: 25–75% (l)LA/GA and 0–70% (dl)LA/GA are amorphous; 70/30 GA/LA has the highest water uptake, while 50/50 is reported as most unstable to hydrolysis; Vicryl is 8% (l)LA and 92% GA.
- Poly(caprolactone) degrades slowly: homopolymer degradation is on the order of 2–3 years, and PCL with initial average molecular weight 50,000 takes about 3 years for complete in vitro degradation.
- Poly(propylene fumarate) degrades to fumaric acid and propylene glycol; time to 20% original weight loss ranged from 84 days (PPF/β-TCP composite) to over 200 days (PPF/CaSO4 composite). PPF formulations showed maximum curing temperatures of 38–48°C versus 94°C for PMMA cements, curing times of 1–121 min, and compressive strengths of 1–12 MPa.
- Polyanhydrides degrade by surface erosion; poly(sebacic acid) degrades in about 54 days in saline, while poly(1,6-bis(p-carboxyphenoxy)hexane) is estimated at 1 year. Poly[1,6-bis(carboxyphenoxy)hexane] has a Young’s modulus of 1.3 MPa versus human bone at 40–60 MPa; poly(anhydride-co-imides) reached compressive strengths of 50–60 MPa, and photocrosslinked systems showed compressive strengths of 30–40 MPa and tensile strengths of 15–27 MPa.
- Degradable polyurethanes based on lysine diisocyanate showed varied properties: dl-lactide networks were rigid (Tg = 60°C) with ultimate tensile strengths of ~40–70 MPa, caprolactone triol networks were low-modulus elastomers with tensile strengths of 1–4 MPa, and copolymer networks had elongation up to 600% with compressive strengths of 3–25 MPa. In vivo, porous polyurethane artificial skin degraded almost completely 4–8 weeks after implantation in guinea pigs with no adverse tissue reaction.
Methods
- Design: narrative literature review; no primary experimental study or systematic review protocol is reported.
- Data/sample: published literature on biodegradable synthetic polymers, including synthesis, properties, degradation, biocompatibility, and injectable polymer systems; Tables 1–3 summarize polymer properties and precursors.
- Analysis: qualitative synthesis of major polymer classes, their degradation modes/products, mechanical properties, biocompatibility, and potential for injectable tissue-engineering compositions.
Limitations
- Stated: the paper notes that Table 2 data “should be used as a guide only” and that sufficient data are not available to provide a comprehensive list of properties for polyanhydrides, polycarbonates, polyurethanes, and polyphosphazenes.
- Stated: for polyanhydrides, no data are reported about polymer sterilizability and heat generation during polymerization; for degradable polyurethanes, the effect of degradation products and how they are removed from the body are not clearly understood.
- Evident: as a narrative review, it lacks systematic search criteria, study quality appraisal, and meta-analysis, so conclusions depend on the cited literature and may not comprehensively cover all biodegradable polymers or tissue-engineering applications.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
1 Valid · 20 Not valid · 105 Not checked · 89 Own results and interpretations
Every source the paper cites for this claim was checked and supports it.
In the paper
“A meniscal replica implanted contained only fibro-cartilage after 18 weeks and decreased the degradation of the articular cartilage.”
What the sources say
- Supportedcites De Groot et al.., 1996 source
The Aliphatic PU network passage (page not provided) reports that articular-cartilage degeneration was less severe with the prosthesis than in meniscectomized control knees. It also says the prostheses contained only fibrocartilage after 18 weeks. Degeneration was reduced, not eliminated. (LLM, conf=0.91)
plainstates a causeSingle case- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
In the paper
“The compressive strengths varied between 1 and 12 MPa”
What the sources say
- Not matchedcites Peter et al., 1998a
Couldn’t be matched to a paper in Crossref, so it can’t be checked.
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Not matched
In the paper
“Cross-linking characteristics reported for PPF, N-vinyl pyrrolidone (N-VP), benzoyl peroxide, sodium chloride, and TCP indicate that for a range of formulations, the maximum temperature varied within 38 to about 48ºC, compared to 94ºC observed for polymethylmethacrylate (PMMA) cements.”
What the sources say
- Not matchedcites Peter et al., 1998a
Couldn’t be matched to a paper in Crossref, so it can’t be checked.
hedged- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Not matched
None of the sources cited for this claim could be matched to a paper in Crossref, so there is nothing to check it against.
In the paper
“Based on in-vitro studies, the time required to reach 20% loss in original weight ranged from 84 (PPF/ß-TCP composite) to over 200 days (PPF/CaSO 4 composite)”
What the sources say
- Not matchedcites Peter et al., 1997b
Couldn’t be matched to a paper in Crossref, so it can’t be checked.
- Not matchedcites Kharas et al., 1997
Couldn’t be matched to a paper in Crossref, so it can’t be checked.
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Not matched
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“These composite materials exhibit compressive strengths in the range 2 to 30 MPa.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
94 more claims
Create a free account to see all 215 claims and to verify the 2 references still open.
- It may state two separate claims as one. 62
- Probably not a substantial claim. 76
- The quote only partly states this claim. 1
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“Advantages include a tightly controlled manufacturing process, accurate reproducibility, adjustable biodegradability, and a wide variety of both chemical and physical properties.[ 171 ]”
From Unraveling and Harnessing the Immune Response at the Cell–Biomaterial Interface for Tissue Engineering Purposes (2024) · cites this paper as [171]
Experimental — accuracy not yet measured
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
§ Polyanhydrides
“Polyanhydrides degrades by surface erosion (Kohn and Langer, 1997) and their main applications are in controlled drug delivery.”
§ Conclusions
“Polyanhydride degrade by bulk erosion and their main applications are in controlled drug delivery.”
Citations
Cites
Synthetic biodegradable polymers as orthopedic devices
Middleton, J. C., & Tipton, A. J. (2000) · Biomaterials · doi:10.1016/s0142-9612(00)00101-0 · Cited by 2,741 · cited 4×
“…developments in siloxane-based polyurethanes, which have greater in-vivo stability than conventional polyetherurethanes (e.g., poly(tetramethylene oxide) (PTMO)-based) have provided opportunities for development of a range of medical implants for chronic applications (Gunatillake et al., 2001).”
BackgroundInfluentialBiomaterial developments for bone tissue engineering
Burg, K. J. L., Porter, S., & Kellam, J. F. (2000) · Biomaterials · doi:10.1016/s0142-9612(00)00102-2 · Cited by 1,643 · cited 1×
“Polyesters have also been considered for development of tissue engineering applications (Hubbell, 1995; Thomson et al 1995a, Yazemski et al. 1996; Wong and Mooney, 1997), particularly for bone tissue engineering (Kohn and Langer, 1997; Burg et al., 2000).”
BackgroundChandra, R. (1998) · Progress in Polymer Science · doi:10.1016/s0079-6700(97)00039-7 · Cited by 1,462
Biodegradable polymers for use in surgery—polyglycolic/poly(actic acid) homo- and copolymers: 1
Gilding, D. K., & Reed, A. M. (1979) · Polymer · doi:10.1016/0032-3861(79)90009-0 · Cited by 1,345
Biomaterials in Tissue Engineering
Hubbell, J. A. (1995) · Nature Biotechnology · doi:10.1038/nbt0695-565 · Cited by 1,060 · cited 1×
“Polyesters have also been considered for development of tissue engineering applications (Hubbell, 1995; Thomson et al 1995a, Yazemski et al. 1996; Wong and Mooney, 1997), particularly for bone tissue engineering (Kohn and Langer, 1997; Burg et al., 2000).”
BackgroundPolylactic Acid for Surgical Implants
KULKARNI, R. K. (1966) · Archives of Surgery · doi:10.1001/archsurg.1966.01330050143023 · Cited by 841
Evolution of bone transplantation: molecular, cellular and tissue strategies to engineer human bone
Yaszemski, M. J., Payne, R. G., Hayes, W. C., Langer, R., & Mikos, A. G. (1996) · Biomaterials · doi:10.1016/0142-9612(96)85762-0 · Cited by 729
Miller, R. A., Brady, J. M., & Cutright, D. E. (1977) · Journal of Biomedical Materials Research · doi:10.1002/jbm.820110507 · Cited by 722 · cited 2×
“For the (l)LA/GA copolymers, resistance to hydrolysis is more pronounced at either end of the copolymers compositions range (Miller et al., 1977; Gilding and Reed, 1979; Reed and Gilding, 1981; Vert et al., 1984).”
BackgroundInjectable biodegradable materials for orthopedic tissue engineering
Temenoff, J. S., & Mikos, A. G. (2000) · Biomaterials · doi:10.1016/s0142-9612(00)00108-3 · Cited by 554 · cited 8×
“A number of methods have been reported to prepare PPF, and each results in different polymer properties (Peter et al., 1997a,b, 1999; Temenoff and Mikos 2000).”
BackgroundMethodInfluentialLeong, K. W., Brott, B. C., & Langer, R. (1985) · Journal of Biomedical Materials Research · doi:10.1002/jbm.820190806 · Cited by 541 · cited 12×
“The polyurethanes ranged from elastomers with elongations at break as high as 780 %, but with low tensile strengths (5.8 to 8.1 MPa).”
BackgroundInfluential
Research works printed but not linked: 5
- Scranton A, Bowman C, Peiffer R, eds. ACS Symposium Series 673; American Chemical Society, Washington DC. pp 189-202.
- Ratner BD, Hoffman AS, Schoen FJ, Lemon JE, eds. Aca- demic Press, San Diego. pp 65-73.
- Lamba NMK, Woodhouse KA, Cooper SL (1998) Poly- urethanes in Biomedical Applications. CRC Press: New York p 205-241.
- Mark JE, Alcock HR, West R (1992) Inorganic Poly- mers. Prentice Hall, Upper Saddle River, NJ. Chapter
- Ng SY, Vandamme T, Tayler MS, Heller J (1997) Syn- thesis and erosion studies of self-catalysed poly(orthoester)s. Macromolecules 30: 770-772.
Cited by
Items 1,001–1,100 of 1,762
Sahvieh, S., Oryan, A., Hassanajili, S., & Kamali, A. (2020) · Cell and Tissue Research · doi:10.1007/s00441-020-03284-9 · Cited by 13
Easy degradable polymeric gel with extremely base-labile cross-linking
Chang, R., Li, N., Qin, J., et al. (2015) · Polymer · doi:10.1016/j.polymer.2015.01.037 · Cited by 12
Highly efficient enzymatic catalysis for cyclocarbonate polymerization
Luo, X., Feng, J. X., Wang, H.-F., Su, W., Zhang, X., & Zhuo, R. (2010) · Polymer Journal · doi:10.1038/pj.2010.69 · Cited by 12
Kim, J. H., Ko, N. R., Jung, B., et al. (2016) · Macromolecular Research · doi:10.1007/s13233-016-4130-5 · Cited by 12
Cheng, C., Huang, J.-J., Liao, Z., Huang, S.-Y., Lee, D., & Xin, Z. (2017) · Polymer Chemistry · doi:10.1039/c7py00182g · Cited by 12
Carmagnola, I., Chiono, V., Abrigo, M., Ranzato, E., Martinotti, S., & Ciardelli, G. (2019) · Journal of Biomaterials Science Polymer Edition · doi:10.1080/09205063.2019.1580954 · Cited by 11
“Currently, aliphatic polyesters, among which the family of poly(lactic acid)s, are widely applied synthetic bioresorbable polymers for the development of drug delivery systems [1], tissue fixation devices [2], wound dressings [3, 4] and cardiovascular devices [5, 6], due to their suitable physico-chemical properties a…”
BackgroundFabrication and characterization of biopolymer fibers for 3D oriented microvascular structures
Fan, X., & Keynton, R. S. (2019) · Journal of Micromechanics and Microengineering · doi:10.1088/1361-6439/ab2349 · Cited by 12
“PGA has high crystallinity (46%–50%), excellent mechanical properties, and is not soluble in the most organic solvents, except highly fluorinated organic solvent such as hexafluoro isopropanol (HFIP)[67].”
BackgroundBialik, M., Kuras, M. J., Sobczak, M., & Olędzka, E. (2019) · Expert Opinion on Drug Delivery · doi:10.1080/17425247.2019.1651716 · Cited by 12
“In addition, long-term studies on the effects of DDSs and conjugates on organisms must be carried out.”
BackgroundInfluentialStankevich, K. S., Schepetkin, I. A., Goreninskii, S., Lavrinenko, A. K., Больбасов, Е. Н., Kovrizhina, A. R., Kirpotina, L. N., Filimonov, V. D., Khlebnikov, А. I., Tverdokhlebov, S. I., et al. (2019) · ACS Biomaterials Science & Engineering · doi:10.1021/acsbiomaterials.9b01401 · Cited by 18
Degradable polyanhydride networks derived from itaconic acid
Sajjad, H., Lillie, L. M., Lau, C. M., Ellison, C. J., Tolman, W. B., & Reineke, T. M. (2021) · Polymer Chemistry · doi:10.1039/d0py01388a · Cited by 14
Ma, X., Wu, T., Robich, M. P., Wang, X., Wu, H., Buchholz, B., & McCarthy, S. (2010) · PubMed · Cited by 18
Abazari, M. F., Karizi, S. Z., Hajati‐Birgani, N., Kohandani, M., Torabinejad, S., Nejati, F., Nasiri, N., Maleki, M. H., Mohajerani, H., & Mansouri, V. (2021) · Polymers for Advanced Technologies · doi:10.1002/pat.5366 · Cited by 14
Biomaterials Applicable for Alveolar Sockets Preservation: In Vivo and In Vitro Studies
Kunert‐Keil, C., Gredes, T., & Gedrange, T. (2011) · InTech eBooks · doi:10.5772/18459 · Cited by 13
“It is known that the degradation product of PLA, lactic acid, is normally present in the body, can enter the tricarbonxylic acid cycle and is excreted as H2O and CO2 (Gunatillake and Adhikari 2003).”
BackgroundKallukalam, B. C., Jayabalan, M., & Sankar, V. (2008) · Biomedical Materials · doi:10.1088/1748-6041/4/1/015002 · Cited by 12
Lee, W., Wiseman, M. E., Cho, N., Glenn, J. S., & Frank, C. W. (2009) · Biomaterials · doi:10.1016/j.biomaterials.2009.08.035 · Cited by 12
“In order to verify the validity of this proposed scheme, we prepared BSA-encapsulated poly(lactic-co-glycolic acid) (PLGA) microspheres using a well-established double emulsion technique [16].”
MethodOsteoblast Behavior on Novel Porous Polymeric Scaffolds
Fernández, J. M., Cortizo, M. S., Cortizo, A. M., & Abraham, G. A. (2011) · Journal of Biomaterials and Tissue Engineering · doi:10.1166/jbt.2011.1002 · Cited by 12
Biomaterials: Historical Overview and Current Directions
Woo, R. K., Jenkins, D., & Greco, R. S. (2004) · CRC Press eBooks · doi:10.1201/9780203500224-5 · Cited by 12
van Minnen, B., Stegenga, B., van Leeuwen, M. B. M., et al. (2007) · Journal of Oral and Maxillofacial Surgery · doi:10.1016/j.joms.2005.11.120 · Cited by 12
Protocols for Biomaterial Scaffold Fabrication
Seidi, A., & Ramalingam, M. (2012) · Wiley eBooks · doi:10.1002/9781118371183.ch1 · Cited by 13
Safety Issues, Environmental Impacts, and Health Effects of Biopolymers
Ragitha, V. M., & Edison, L. K. (2022) · Springer eBooks · doi:10.1007/978-981-16-6603-2_54-1 · Cited by 17
PLGA: A Wow Smart Biodegradable Polymer in Drug Delivery System
Sonawane, S. S., Pingale, P., & Amrutkar, S. V. (2023) · Indian Journal of Pharmaceutical Education and Research · doi:10.5530/ijper.57.2s.23 · Cited by 12
Combinatorial strategies for cell transplantation in traumatic spinal cord injury
Jagrit, V., Koffler, J. Y., & Dulin, J. N. (2024) · Frontiers in Neuroscience · doi:10.3389/fnins.2024.1349446 · Cited by 13
“Among these polylactic acid, polyglycolic acid, and polycaprolactone are biodegradable synthetic polymers and are well known for their high mechanical strength, flexibility, and nontoxic degradability (Gunatillake and Adhikari, 2003; Shalumon et al., 2011).”
BackgroundElectrospun scaffolds for heart valve tissue engineering
Gürbüz, B., Balikci, E., & Baran, E. T. (2025) · Exploration of BioMat-X · doi:10.37349/ebmx.2025.101331 · Cited by 14
Microfabrication of polymers for bioMEMS
Rezai, P., Wu, W.-I., & Selvaganapathy, P. R. (2012) · Elsevier eBooks · doi:10.1533/9780857096272.1.3 · Cited by 14
Mabrouk, M., Choonara, Y. E., Kumar, P., et al. (2016) · Polymers · doi:10.3390/polym8060232 · Cited by 11
“This phenomenon was caused by the direct degradation of the PCL/PAA scaffolds to PCL and PAA acidic degradation products, as reported previously [29,30].”
ResultPeng, Z., & Zou, T. (2019) · Journal of Macromolecular Science Part B · doi:10.1080/00222348.2019.1593601 · Cited by 11
“However, PLA and PLGA degrade rapidly in the body and may elicit inflammatory response in the host tissue because of the release of acidic degradation products.([21,22]) Therefore, some modifications for functionalization would”
BackgroundSynthesis of PLA/SBA-15 Composite Scaffolds for Bone Tissue Engineering
Chanes‐Cuevas, O. A., Arellano, U., Alvarez‐Gayosso, C., Suaste-Olmos, F., Villarreal-Ramírez, E., Álvarez-Fregoso, O., García-Hipólito, M., González‐Alva, P., & Álvarez-Pérez, M. A. (2020) · Materials Research · doi:10.1590/1980-5373-mr-2020-0211 · Cited by 11
Recent advances in the synthesis of zirconium complexes and their catalytic applications
Asim, W., Waheeb, A. S., Awad, M. A., Kadhum, A. M., Ali, A., Mallah, S. H., Iqbal, M. A., & Kadhim, M. M. (2021) · Journal of Molecular Structure · doi:10.1016/j.molstruc.2021.131925 · Cited by 11
Biocompatible Customized 3D Bone Scaffolds Treated with CRFP, an Osteogenic Peptide
Mustahsan, V. M., Anugu, A., Komatsu, D. E., Kao, I., & Pentyala, S. (2021) · Bioengineering · doi:10.3390/bioengineering8120199 · Cited by 11
“These polymers are biodegradable and form lactic acid which dissolves in the body [40].”
BackgroundMacromolecular chemistry: An introduction
Selvaraj, C., Dinesh, D. C., Rajaram, K., Sundaresan, S., & Singh, S. K. (2023) · Elsevier eBooks · doi:10.1016/b978-0-323-90995-2.00007-2 · Cited by 19
Tissue Engineering of Skeletal Muscle
Klumpp, D., Raymund, H., & Beier, J. (2011) · InTech eBooks · doi:10.5772/21197 · Cited by 12
“6 months) (Gunatillake & Adhikari 2003).”
Design and development of reactive injectable and settable polymeric biomaterials
Page, J. M., Harmata, A. J., & Guelcher, S. A. (2013) · Journal of Biomedical Materials Research Part A · doi:10.1002/jbm.a.34665 · Cited by 12
“Low molecular weight, aliphatic diisocyanates such as 1,4 butane diisocyanate and 1,6 hexamethylene diisocyanate are known to have nontoxic degradation products and are widely utilized in biomedical polymers.(65,134) However, both these diisocyanates have low vapor pressures and are highly toxic as inhalants, limiting…”
BackgroundBiomaterials for Bone Tissue Engineering
Chen, Q. Z. (2013) · Humana Press eBooks · doi:10.1007/978-1-62703-417-3_23 · Cited by 12
Puhl, S., Ilko, D., Li, L., et al. (2014) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2014.10.047 · Cited by 11
Mohanty, M. C. S. (2015) · Journal of Tissue Science & Engineering · doi:10.4172/2157-7552.1000142 · Cited by 17
“Biodegradable polymers such as poly (glycolic acid), poly (lactic acid) and their copolymers, poly (pdioxanone), and copolymers of trimethylene carbonate and glycolide have been extensively used in a number of clinical applications [10].”
BackgroundEnhanced proliferation of HeLa cells on PLLA-PCL and PLGA-PCL multiblock copolymers
Suga, T., Xuyen, N. T., Matsumoto, K., Jikei, M., Takahashi, K., Kubota, H., & Tamura, T. (2017) · Polymer Journal · doi:10.1038/pj.2017.21 · Cited by 11
Formulation and Evaluation of FSM-Alginate Beads of Vildagliptin
CHERIAN, A. S., Johns, G. B., Raj, R. P., et al. (2019) · Journal of Drug Delivery and Therapeutics · doi:10.22270/jddt.v9i4-a.3289 · Cited by 11
Reinforcement of Colonic Anastomosis with Improved Ultrafine Nanofibrous Patch: Experiment on Pig
Rosendorf, J., Klicova, M., Červenková, L., Horáková, J., Klápšťová, A., Hošek, P., Pálek, R., Ševčík, J., Polák, R., Treska, V., et al. (2021) · Biomedicines · doi:10.3390/biomedicines9020102 · Cited by 11
Personalized Bone Reconstruction and Regeneration in the Treatment of Craniosynostosis
Tiberio, F., Cacciotti, I., Frassanito, P., Nocca, G., Tamburrini, G., Arcovito, A., & Lattanzi, W. (2021) · Applied Sciences · doi:10.3390/app11062649 · Cited by 12
Chang, C., & Yeh, Y. (2021) · Macromolecular Bioscience · doi:10.1002/mabi.202100248 · Cited by 14
Uehlin, A. F., Vines, J. B., Feldman, D. S., Nyairo, E., Dean, D. R., & Thomas, V. (2022) · Pharmaceutics · doi:10.3390/pharmaceutics14020277 · Cited by 11
Production of Mesoglycan/PCL Based Composites through Supercritical Impregnation
Liparoti, S., Mottola, S., Viscusi, G., Belvedere, R., Petrella, A., Gorrasi, G., Pantani, R., & Marco, I. D. (2022) · Molecules · doi:10.3390/molecules27185800 · Cited by 11
7.18 Materials in Tendon and Ligament Repair ☆
Shetye, S. S., Miller, K. S., Hsu, J. E., & Soslowsky, L. J. (2016) · Elsevier eBooks · doi:10.1016/b978-0-12-803581-8.09252-3 · Cited by 14
Duan, H., Ye, L., Wu, X., Guan, Q., Yang, X., Han, F. L., Liang, N., Wang, Z., & Wang, Z. (2014) · Vascular · doi:10.1177/1708538114550737 · Cited by 13
“Nevertheless, these polymers degrade very quickly in vivo, and this means that they rapidly lose adequate mechanical structure;(15) moreover, they can produce a local acidic environment when they degrade.(16) Polycaprolactone (PCL), another synthetic biodegradable polymer, has a longer degradation time than other poly…”
Andreasen, C. M., Henriksen, S. S., Ding, M. L., et al. (2016) · Journal of Orthopaedic Translation · doi:10.1016/j.jot.2016.07.002 · Cited by 11
“, poly-D,L-lactic acid (PDLLA), poly-glycolic acid, or poly-hydroxy butyrate [3,9].”
BackgroundCrosslinkable poly(lactic acid)‐based materials: Biomass‐derived solution for barrier coatings
Mehtiö, T., Anghelescu‐Hakala, A., Hartman, J., Kunnari, V., & Harlin, A. (2016) · Journal of Applied Polymer Science · doi:10.1002/app.44326 · Cited by 11
Hege, C. S., Siegel-Axel, D. I., Köhler, K., Delorme, N., Houérou, V. L., Schiller, S., & Dolderer, J. H. (2020) · ACS Applied Polymer Materials · doi:10.1021/acsapm.0c00359 · Cited by 13
“[1,2] Even though these biopolymers found widespread applications in the biomedical filed, their diversity in terms of their chemical nature (homo- or copolymers), chemicals used during synthesis (e.”
BackgroundIntroduction of Polymers and Polymer Composites: Basic Fundamentals
Parida, S. K., Satpathy, A., Dalai, A., & Mishra, S. (2024) · Engineering materials · doi:10.1007/978-981-97-2075-0_1 · Cited by 16
Advances in biomaterials-based tissue engineering for regeneration of female reproductive tissues
Kim, Y. H., Kim, H., & Hong, I. (2025) · Biofabrication · doi:10.1088/1758-5090/adae38 · Cited by 14
“Several factors, including copolymer ratios, crystallinity, molecular weight, porosity, implantation site, monomer residue, structural configuration, morphological traits, and applied stresses, affect polyester degradation rates [56].”
Shahbazi, S., Jafari, Y., Moztarzadeh, F., & Sadeghi, G. M. M. (2014) · Journal of Applied Polymer Science · doi:10.1002/app.40932 · Cited by 9
Synthesis and Characterization of Terpolymers of poly(L-lactide-glycolide-ε-caprolactone)
Yang, Y., Liu, W., Fang, J., Zhao, Y., Zhao, Y., Huang, T., Cui, J., Wu, W., Li, X., & Zhou, Z. (2018) · Journal of Macromolecular Science Part B · doi:10.1080/00222348.2018.1493171 · Cited by 10
Nanoengineered biomaterials for lung regeneration
Moztarzadeh, S., Mottaghy, K., Sefat, F., Samadikuchaksaraei, A., & Mozafari, M. (2018) · Elsevier eBooks · doi:10.1016/b978-0-12-813355-2.00013-2 · Cited by 15
Tsubosaka, M., Maruyama, M., Lui, E., Moeinzadeh, S., Huang, E. E., Kushioka, J., Hirata, H., Jain, C. M., Storaci, H. W., Chan, C. K., et al. (2023) · Journal of Biomedical Materials Research Part A · doi:10.1002/jbm.a.37495 · Cited by 10
“Fabrication of bioactive polyphenolic biomaterials for bone tissue engineering”
Hobbi, P., Okoro, O. V., Nie, L., & Shavandi, A. (2023) · Materials Today Sustainability · doi:10.1016/j.mtsust.2023.100541 · Cited by 13
Gradzik, B., Stenzel, A., Boccaccini, A. R., & Fray, M. E. (2015) · Designed Monomers & Polymers · doi:10.1080/15685551.2015.1041080 · Cited by 9
“[1,2] The recent two decades, however, strongly focused on exploitation of regenerative potential of living tissues, specifically using temporary, biodegradable polymeric templates (scaffolds) which are seeded with cells for tissue engineering.[2,3] Biodegradable synthetic polymers such as poly(glycolic acid) (PGA), p…”
BackgroundYou, H., Lee, E.-U., Kim, Y.-K., et al. (2014) · Biomaterials Research · doi:10.1186/2055-7124-18-12 · Cited by 10
“widely used resorbable membrane, usually have superior biocompatibility and tissue affinity than synthetic membrane due to its excellent biological properties [1,2].”
BackgroundKöhler, J., Marquardt, F., Teske, M., Keul, H., Sternberg, K., & Möller, M. (2013) · Biomacromolecules · doi:10.1021/bm401428b · Cited by 11
In situ monitoring of isophorone diisocyanate-based flexible polyurethane foams formation
Eceiza, I., Irusta, L., Barrio, A., et al. (2016) · Journal of Cellular Plastics · doi:10.1177/0021955x16670579 · Cited by 10
“Initially, SnOc was selected because it has been accepted by the Food and Drug Administration and is commonly used in the polymerization of PUR for medical implants and tissue engineering.(24) Table 2 summarizes the values of the main foam generation parameters as a function of catalyst concentration.”
MethodJohnson, I., Lin, J., & Liu, H. H. (2017) · Springer eBooks · doi:10.1007/978-3-319-73664-8_13 · Cited by 11
Botlhoko, O. J., Makwakwa, D., Ray, S. S., et al. (2018) · Journal of Applied Polymer Science · doi:10.1002/app.47387 · Cited by 10
Inorganic and Composite Bioactive Scaffolds for Bone Tissue Engineering
Bretcanu, O., Chen, Q. Z., & Boccaccini, A. R. (2008) · CRC Press eBooks · doi:10.1201/9780849379741.pt1 · Cited by 11
Lee, S. J., Yoo, J. J., & Atala, A. (2014) · Polymer(Korea) · doi:10.7317/pk.2014.38.2.113 · Cited by 11
Yang, S., Wang, J., Tan, H., et al. (2014) · International Journal of Nanomedicine · doi:10.2147/ijn.s52421 · Cited by 10
Feroci, F., Lenzi, E., Kröning, K. C., et al. (2011) · Updates in Surgery · doi:10.1007/s13304-011-0059-6 · Cited by 10
“Therefore, they do not leave any residual, extraneous material after 6 months [30].”
BackgroundCarfì-Pavia, F., Turturici, G., Geraci, F., Brucato, V., Carrubba, V. L., Luparello, C., & Sconzo, G. (2009) · Journal of Biosciences · doi:10.1007/s12038-009-0101-8 · Cited by 10
“J. Biosci. 34(6), December 2009 to give rise to all somatic cell lineages ( Gunatillake and Adhikari 2003 ).”
BackgroundChitosan impregnation with biologically active tryaryl imidazoles in supercritical carbon dioxide
Cherkasova, A. M., Glagolev, N. N., Shienok, A. I., Demina, T. S., Kotova, S., Zaichenko, N. L., Akopova, T. A., Timashev, P. S., Bagratashvili, V. N., & Solovieva, A. B. (2016) · Journal of Materials Science Materials in Medicine · doi:10.1007/s10856-016-5753-y · Cited by 10
“and polyesters, primarily, polymers of lactic and glycolic acid and their copolymers with aminoacids [10–14], polysaccharides, such as cellulose and its derivatives [15, 16], dextran [17], alginic acid [18], chitosan [19–23] etc.”
BackgroundRealization and testing of multi-material 3D printer for bone scaffold fabrication
Whulanza, Y., Hidayaturrahmi, P., Kurniawati, T., et al. (2017) · AIP conference proceedings · doi:10.1063/1.4976786 · Cited by 10
“Since the molecular weight of synthetic polymers can be controlled by synthetic or purification procedures, their physical properties can be well-defined [9].”
BackgroundImproved survival of cardiac cells on surface modified electrospun nanofibers
Pushp, P., Ferreira, F. C., Cabral, J. M. S., et al. (2017) · Polymer Science Series A · doi:10.1134/s0965545x17040058 · Cited by 10
Polymeric Scaffolds for Tissue Engineering Applications
Yoon, D. M., & Fisher, J. P. (2007) · CRC Press eBooks · doi:10.1201/9781420008333.sec2 · Cited by 14
Myocardial Cell Signaling During the Transition to Heart Failure
Zeglinski, M. R., Moghadam, A. R., Ande, S. R., Sheikholeslami, K., Mokarram, P., Sepehri, Z., Rokni, H., Mohtaram, N. K., Poorebrahim, M., Masoom, A., et al. (2018) · Comprehensive physiology · doi:10.1002/cphy.c170053 · Cited by 13
Pandey, A., Sharma, R. K., & Balani, K. (2014) · Wiley eBooks · doi:10.1002/9781118950623.ch1 · Cited by 11
Impact of 3D-printed PLA coatings on the mechanical and adhesion properties of AM60 magnesium alloys
Rezanezhad, S., & Azadi, M. (2023) · Composites Part C Open Access · doi:10.1016/j.jcomc.2023.100415 · Cited by 14
Niclot, F. B., Lim, J., McCulloch, P. C., Corradetti, B., & Taraballi, F. (2024) · Current Stem Cell Reports · doi:10.1007/s40778-024-00239-6 · Cited by 11
“Polymeric scaffolds are particularly advantageous for applications that require well-defined mechanical features over time since their formulation and biological properties can be tailored ad-hoc [148].”
hajipour, F. P., Feyzbakhsh, A., Maleknia, L., & Ahanian, I. (2024) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2024.138745 · Cited by 9
3D printed biomaterials: From fabrication techniques to clinical applications: A systematic review
Kaur, A., Singh, S., Bala, N., & Kansal, S. K. (2025) · European Polymer Journal · doi:10.1016/j.eurpolymj.2024.113606 · Cited by 10
The Nobori biolimus-eluting stent: update of available evidence
Piccolo, R., Nicolino, A., & Danzi, G. B. (2014) · Expert Review of Medical Devices · doi:10.1586/17434440.2014.894458 · Cited by 9
Pulmonary system responses to biomaterials
Bahmanpour, A. H., Navaei, T., & Ahadi, F. (2020) · Elsevier eBooks · doi:10.1016/b978-0-08-102967-1.00029-3 · Cited by 10
Hamza, A. A., El‐Bakary, M. A., Ibrahim, M., Elgamal, M., & El‐Sayed, N. M. (2022) · Polymer Bulletin · doi:10.1007/s00289-021-04070-5 · Cited by 9
Hüner, K., Sarac, B., Yüce, E., Rezvan, A., Mičušík, M., Omastová, M., Eckert, J., & Saraç, A. S. (2022) · Molecular Systems Design & Engineering · doi:10.1039/d2me00181k · Cited by 9
Furkó, M., Detsch, R., Tolnai, I., Balázsi, K., Boccaccini, A. R., & Balázsi, C. (2023) · Ceramics International · doi:10.1016/j.ceramint.2023.02.231 · Cited by 12
Natural polysaccharide-based hydrogel bioprinting for articular cartilage repair
Wu, X., Cheng, X., Kang, M., Dong, R., Zhao, J., & Qu, Y. (2023) · Frontiers in Materials · doi:10.3389/fmats.2023.1204318 · Cited by 13
Liu, X., Grant, D. M., Palmer, G., et al. (2014) · Journal of Biomedical Materials Research Part B Applied Biomaterials · doi:10.1002/jbm.b.33324 · Cited by 9
“Phosphate glass fibers (PGF) can be used as reinforcement for biodegradable polymers, such as poly (glycolic acid), poly (lactic acid) and their copolymers, poly (caprolactone), poly (p-dioxanone), to overcome their insufficient load-bearing capability for tissue engineering applications.(20,21) Therefore, the PGF com…”
The effect of a bioactive tissue‐engineered sling in a rat of stress incontinence model
Kim, I. G., Piao, S., Hong, S., Kim, S. W., Hwang, T., Oh, S. H., Lee, J. H., & Lee, J. Y. (2011) · Journal of Biomedical Materials Research Part A · doi:10.1002/jbm.a.33259 · Cited by 9
Bayramoğlu, G., Kayaman‐Apohan, N., Kahraman, M. V., Karadenizli, S., Kuruca, S. E., & Güngör, A. (2011) · Polymers for Advanced Technologies · doi:10.1002/pat.2059 · Cited by 9
Chen, J., Fan, X., Zhongcheng, Z., Zou, J., & Ruan, J. (2010) · Polymer-Plastics Technology and Engineering · doi:10.1080/03602551003664610 · Cited by 9
“However, the main problems associated with PLGA are that the release of acidic degradation by-products can lead to a decreased pH value in the vicinity of the implants which may result in inflammatory response [ 6-9 ] .”
BackgroundJovanovic, D., Engels, G. E., Plantinga, J. A., Bruinsma, M., van Oeveren, W., Schouten, A. J., van Luyn, M. J. A., & Harmsen, M. C. (2010) · Journal of Biomedical Materials Research Part A · doi:10.1002/jbm.a.32817 · Cited by 11
POLYMER: A BOON TO CONTROLLED DRUG DELIVERY SYSTEM
Chandel, P., Rajkumari, & Kapoor, A. (2016) · International Research Journal of Pharmacy · doi:10.7897/2230-8407.04405 · Cited by 9
“However, a major problem has been the toxicity of degradation products, particularly those derived from the DiIsocyanate component.(16)”
BackgroundMethodProcess-induced degradation of bioresorbable PDLGA in bone tissue scaffold production
Little, H., Clarke, S. A., Cunningham, E., & Buchanan, F. (2017) · Journal of Materials Science Materials in Medicine · doi:10.1007/s10856-017-6019-z · Cited by 9
Turner, Z. R., Lamb, J. V., Robinson, T. P., Mandal, D., Buffet, J., & O'Hare, D. M. (2021) · Dalton Transactions · doi:10.1039/d1dt00252j · Cited by 12
Gu, J., Zhou, Z., Huang, T., Wu, W., Liu, W., Zhao, Y., Chen, P., Zhou, Z., Wang, D., Zhang, C., et al. (2021) · Journal of Macromolecular Science Part B · doi:10.1080/00222348.2021.2002457 · Cited by 9
“PLGA degrade rapidly in the body and may elicit inflammatory response in the host tissue because of the release of acidic degradation products.([27]) Therefore, some modifications for functionalization would be necessary for their applications in biomedical materials.”
BackgroundRivero, P. J., Fuertes, J. P., Vicente, A., et al. (2021) · Polymers · doi:10.3390/polym13244312 · Cited by 9
“Among all the polymeric precursors, polycaprolactone (PCL) polymer can be used as a promoting biomaterial due to its intrinsic characteristics such as nontoxicity, robust mechanical properties, biocompatibility and excellent biodegradability [34], showing at the same time a highly hydrophobic behavior [35].”
BackgroundImmuno‐Modulatory Effects of Microparticles Formulated from Degradable Polystyrene Analogue
Truong, T. H. A., Mothe, S. R., Min, J. L., Tan, H. M., Jackson, A. W., Nguyen, D. T., Ye, D. K. J., Kanaujia, P., Thoniyot, P., & Dang, T. T. (2022) · Macromolecular Bioscience · doi:10.1002/mabi.202100472 · Cited by 9
Design and fabrication method of bi-layered fibrous scaffold for cartilage regeneration
Dabasinskaite, L., Krugly, E., Baniukaitienė, O., Čiužas, D., Martuzevičius, D., Jankauskaitė, L., Malinauskas, M., & Ūsas, A. (2022) · Biochemical Engineering Journal · doi:10.1016/j.bej.2022.108413 · Cited by 9
Potential of Biodegradable Synthetic Polymers for Use in Small-diameter Vascular Engineering
Osipova, O. S., Laktionov, P. P., & Karpenko, A. A. (2022) · Macromolecular Research · doi:10.1007/s13233-022-0056-2 · Cited by 10
Advancements and Utilizations of Scaffolds in Tissue Engineering and Drug Delivery
Malviya, R., Chauhan, A., Alam, A., & Kaur, A. (2022) · Current Drug Targets · doi:10.2174/1389450123666221011100235 · Cited by 9
Sánchez-Téllez, D. A., Téllez-Jurado, L., & Rodríguez-Lorenzo, L. M. (2015) · Journal of Materials Science · doi:10.1007/s10853-015-9147-1 · Cited by 9
“The organic degradation of PDMS in the hybrids is determined by several factors such as their structure, type of copolymerization, crystallinity, unreacted monomers, molecular weight, morphology, bond types, and porosity [35].”
BackgroundChen, W., Ko, C., Yang, J.-K., Wu, H., & Lin, J. (2015) · Journal of Artificial Organs · doi:10.1007/s10047-015-0863-8 · Cited by 10
Photopolymerization of biocompatible films containing poly(lactic acid)
Miller, K. R., & Soucek, M. D. (2012) · European Polymer Journal · doi:10.1016/j.eurpolymj.2012.08.006 · Cited by 9
Rouholamin, D., van Grunsven, W., Reilly, G. C., & Smith, P. J. (2016) · Proceedings of the Institution of Mechanical Engineers Part H Journal of Engineering in Medicine · doi:10.1177/0954411916650221 · Cited by 9
“The diffusivity of a gas and the density and dissolving power of a liquid with the relatively low critical point for scCO2 propose a popular choice for fabricating porous structures.(9,12,14) In this technique, polymer or polymer composite discs are equilibrated with scCO2 which diffuses into the polymer structure and…”
BackgroundNew comonomers in malic acid polyesters
Telegdi, J., Trif, L., Nagy, E., Mihály, J., & Molnár, N. (2017) · Journal of Thermal Analysis and Calorimetry · doi:10.1007/s10973-017-6230-7 · Cited by 9
Metadata
- Authors
- CSIRO Molecular Science, B. 1., & Gunatillake, P.
- Corresponding author
- CSIRO Molecular Science, Bag 10, Clayton South MDC, Vic 3169, Australia
- Venue
- European Cells and Materials
- Publisher
- Forum Multimedia Publishing LLC
- Published
- 2003-10-01
- Volume
- 5
- Pages
- 1-16
- ISSN
- 1473-2262 (ISSN-L)
- OpenAlex
- W2106035984
- Cited by
- 1,765
- References
- 97
- Citations by year
- 2026: 43 · 2025: 61 · 2024: 59 · 2023: 80 · 2022: 90 · 2021: 112 · 2020: 102 · 2019: 115 · 2018: 105 · 2017: 128 · 2016: 110 · 2015: 106 · 2014: 110 · 2013: 91 · 2012: 86
- FWCI
- 1.32
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- cc-by
- Locations
- European Cells and Materials (publishedVersion, cc-by)
- PubMed (publishedVersion)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion)
- Topics
- Physical Sciences › Materials Science › Biomaterials › biodegradable polymer synthesis and properties
- Physical Sciences › Engineering › Biomedical Engineering › Bone Tissue Engineering Materials
- Health Sciences › Medicine › Surgery › Surgical Sutures and Adhesives
- Keywords
- tissue engineering, polyesters, polyglycolic acid, polylactic acid, polyanhydrides, polyphosphazenes, polyurethane, poly(propylene fumarate), injectable polymers, orthopedic tissue engineering, biodegradation, biocompatibility, degradation products
- MeSH terms
- Biocompatible Materials, Models, Chemical, Polymers, Tissue Engineering
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.