3D printing geopolymers: A review
Open accessThe DOI matches its Crossref record; 102 of the 102 references it cites were found in a registry or an index.
Abstract
Geopolymers have been considered as a promising alternative to cementitious materials for 3D printing to enhance sustainability of the construction industry. This paper presents a critical review of the state-of-the-art of 3D printing geopolymers from the perspectives of production process, printability requirement, mix design, early-age material properties and sustainability, with a special focus on the effects of different factors such as matrix composition, reinforcement type, curing regime and printing configuration on the fresh and hardened properties of 3D printed geopolymers. The relationship between key fresh properties and printability of geopolymers is discussed, based on which the potential optimal mix proportions are obtained, containing the blended precursors of fly ash, ground granulated blast-furnace slag and silica fume, liquid or solid activator, river sand with a maximum size of 2 mm, thixotropic additives (e.g., nano clay), and retarder (e.g., sucrose). This paper aims to summarise the recent advances in the development of 3D printing techniques suitable for geopolymers and geopolymers feasible for 3D printing, and to identify the knowledge gap, remaining challenges, and opportunities for future research.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Additive manufacturing (3D printing): A review of materials, methods, applications and challenges
Ngo, T. D., Kashani, A., Imbalzano, G., Nguyen, K. T. Q., & Hui, D. (2018) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2018.02.012 · Cited by 8,431
Geopolymer technology: The current state of the art
Duxson, P., Fernández-Jiménez, A., Provis, J. L., Lukey, G. C., Palomo, A., & van Deventer, J. S. J. (2007) · Journal of Materials Science · doi:10.1007/s10853-006-0637-z · Cited by 4,742
3D printing using concrete extrusion: A roadmap for research
Buswell, R. A., Leal de Silva, W. R., Jones, S. Z., & Dirrenberger, J. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2018.05.006 · Cited by 1,604
Geopolymers and Related Alkali-Activated Materials
Provis, J. L., & Bernal, S. A. (2014) · Annual Review of Materials Research · doi:10.1146/annurev-matsci-070813-113515 · Cited by 1,597
One-part alkali-activated materials: A review
Luukkonen, T., Abdollahnejad, Z., Yliniemi, J., Kinnunen, P., & Illikainen, M. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2017.10.001 · Cited by 1,456
Ismail, I., Bernal, S. A., Provis, J. L., San Nicolas, R., Hamdan, S., & van Deventer, J. S. J. (2014) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2013.09.006 · Cited by 1,317
Bos, F., Wolfs, R., Ahmed, Z., & Salet, T. (2016) · Virtual and Physical Prototyping · doi:10.1080/17452759.2016.1209867 · Cited by 1,257
Mix design and fresh properties for high-performance printing concrete
Le, T. T., Austin, S. A., Lim, S., Buswell, R. A., Gibb, A. G. F., & Thorpe, T. (2012) · Materials and Structures · doi:10.1617/s11527-012-9828-z · Cited by 1,218
Developments in construction-scale additive manufacturing processes
Lim, S., Buswell, R. A., Le, T. T., Austin, S. A., Gibb, A. G. F., & Thorpe, T. (2012) · Automation in Construction · doi:10.1016/j.autcon.2011.06.010 · Cited by 1,205
Rheological requirements for printable concretes
Roussel, N. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2018.04.005 · Cited by 1,203
The origins of thixotropy of fresh cement pastes
Roussel, N., Ovarlez, G., Garrault, S., & Brumaud, C. (2011) · Cement and Concrete Research · doi:10.1016/j.cemconres.2011.09.004 · Cited by 1,095
Embodied energy and carbon in construction materials
Hammond, G. P., & Jones, C. I. (2008) · Proceedings of the Institution of Civil Engineers - Energy · doi:10.1680/ener.2008.161.2.87 · Cited by 994
A thixotropy model for fresh fluid concretes: Theory, validation and applications
Roussel, N. (2006) · Cement and Concrete Research · doi:10.1016/j.cemconres.2006.05.025 · Cited by 967
Gosselin, C., Duballet, R., Roux, P., Gaudillière, N., Dirrenberger, J., & Morel, P. (2016) · Materials & Design · doi:10.1016/j.matdes.2016.03.097 · Cited by 962
Deb, P. S., Nath, P., & Sarker, P. K. (2014) · Materials & Design (1980-2015) · doi:10.1016/j.matdes.2014.05.001 · Cited by 941
Influence of NaOH solution on the synthesis of fly ash geopolymer
Rattanasak, U., & Chindaprasirt, P. (2009) · Minerals Engineering · doi:10.1016/j.mineng.2009.03.022 · Cited by 939
Assessment of CO2 reduction of alkali-activated concrete
Yang, K.-H., Song, J.-K., & Song, K.-I. (2013) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2012.08.001 · Cited by 832
Building components for an outpost on the lunar soil by means of a novel 3D printing technology
Cesaretti, G., Dini, E., De Kestelier, X., Colla, V., & Pambaguian, L. (2014) · Acta Astronautica · doi:10.1016/j.actaastro.2013.07.034 · Cited by 806
Measuring the eco-efficiency of cement use
Damineli, B. L., Kemeid, F. M., Aguiar, P. S., & John, V. M. (2010) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2010.07.009 · Cited by 776
Lee, N. K., & Lee, H. K. (2013) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2013.05.107 · Cited by 754
Anisotropic mechanical performance of 3D printed fiber reinforced sustainable construction material
Panda, B., Paul, S. C., & Tan, M. J. (2017) · Materials Letters · doi:10.1016/j.matlet.2017.07.123 · Cited by 742
Fiber-reinforced geopolymer composites: A review
Ranjbar, N., & Zhang, M. (2020) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2019.103498 · Cited by 651
Self-citationGörhan, G., & Kürklü, G. (2014) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2013.10.082 · Cited by 637
Digital Concrete: Opportunities and Challenges
Wangler, T., Lloret, E., Reiter, L., Hack, N., Gramazio, F., Kohler, M., Bernhard, M., Dillenburger, B., Buchli, J., Roussel, N., et al. (2016) · RILEM Technical Letters · doi:10.21809/rilemtechlett.2016.16 · Cited by 636
Fresh and hardened properties of 3D printable cementitious materials for building and construction
Paul, S. C., Tay, Y. W. D., Panda, B., & Tan, M. J. (2018) · Archives of Civil and Mechanical Engineering · doi:10.1016/j.acme.2017.02.008 · Cited by 633
A review of the current progress and application of 3D printed concrete
Zhang, J., Wang, J., Dong, S., Yu, X., & Han, B. (2019) · Composites Part A Applied Science and Manufacturing · doi:10.1016/j.compositesa.2019.105533 · Cited by 629
Role of water in the synthesis of calcined kaolin-based geopolymer
ZUHUA, Z., XIAO, Y., HUAJUN, Z., & YUE, C. (2009) · Applied Clay Science · doi:10.1016/j.clay.2008.09.003 · Cited by 621
Wangler, T., Roussel, N., Bos, F. P., Salet, T. A. M., & Flatt, R. J. (2019) · Cement and Concrete Research · doi:10.1016/j.cemconres.2019.105780 · Cited by 612
Mechanical anisotropy of aligned fiber reinforced composite for extrusion-based 3D printing
Ma, G., Li, Z., Li, W., Wang, F., & Sanjayan, J. (2019) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2019.01.008 · Cited by 610
Mechtcherine, V., Bos, F. P., Perrot, A., da Silva, W. R. L., Nerella, V. N., Fataei, S., Wolfs, R. J. M., Sonebi, M., & Roussel, N. (2020) · Cement and Concrete Research · doi:10.1016/j.cemconres.2020.106037 · Cited by 598
Measurement of tensile bond strength of 3D printed geopolymer mortar
Panda, B., Paul, S. C., Mohamed, N. A. N., Tay, Y. W. D., & Tan, M. J. (2018) · Measurement · doi:10.1016/j.measurement.2017.08.051 · Cited by 592
Marchon, D., Kawashima, S., Bessaies-Bey, H., Mantellato, S., & Ng, S. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2018.05.014 · Cited by 567
Large-scale 3D printing concrete technology: Current status and future opportunities
Xiao, J., Ji, G., Zhang, Y., Ma, G., Mechtcherine, V., Pan, J., Wang, L., Ding, T., Duan, Z., & Du, S. (2021) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2021.104115 · Cited by 532
Fang, G., Ho, W. K., Tu, W., & Zhang, M. (2018) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2018.04.008 · Cited by 528
Self-citationFly ash-based geopolymers: The relationship between composition, pore structure and efflorescence
Zhang, Z., Provis, J. L., Reid, A., & Wang, H. (2014) · Cement and Concrete Research · doi:10.1016/j.cemconres.2014.06.004 · Cited by 527
Panda, B., & Tan, M. J. (2018) · Ceramics International · doi:10.1016/j.ceramint.2018.03.031 · Cited by 520
Additive manufacturing of geopolymer for sustainable built environment
Panda, B., Paul, S. C., Hui, L. J., Tay, Y. W. D., & Tan, M. J. (2017) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2017.08.165 · Cited by 516
Investigation of the rheology and strength of geopolymer mixtures for extrusion-based 3D printing
Panda, B., Unluer, C., & Tan, M. J. (2018) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2018.10.002 · Cited by 482
Shrinkage characteristics of alkali-activated fly ash/slag paste and mortar at early ages
Lee, N. K., Jang, J. G., & Lee, H. K. (2014) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2014.07.007 · Cited by 462
Understanding the rheology of concrete
Roussel, N. (2012) · Woodhead Publishing Limited eBooks · doi:10.1533/9780857095282 · Cited by 461
Large-scale digital concrete construction – CONPrint3D concept for on-site, monolithic 3D-printing
Mechtcherine, V., Nerella, V. N., Will, F., Näther, M., Otto, J., & Krause, M. (2019) · Automation in Construction · doi:10.1016/j.autcon.2019.102933 · Cited by 455
Mix design concepts for 3D printable concrete: A review
Zhang, C., Nerella, V. N., Krishna, A., Wang, S., Zhang, Y., Mechtcherine, V., & Banthia, N. (2021) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2021.104155 · Cited by 421
Improving the 3D printability of high volume fly ash mixtures via the use of nano attapulgite clay
Panda, B., Ruan, S., Unluer, C., & Tan, M. J. (2019) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2018.11.109 · Cited by 405
Yang, T., Zhu, H., Zhang, Z., Gao, X., Zhang, C., & Wu, Q. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2018.04.008 · Cited by 399
Extrusion-based concrete 3D printing from a material perspective: A state-of-the-art review
Mohan, M. K., Rahul, A. V., De Schutter, G., & Van Tittelboom, K. (2021) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2020.103855 · Cited by 384
Mega-scale fabrication by Contour Crafting
Khoshnevis, B., Hwang, D., Yao, K. T., & Yeh, Z. (2006) · International Journal of Industrial and Systems Engineering · doi:10.1504/ijise.2006.009791 · Cited by 378
Method of formulating geopolymer for 3D printing for construction applications
Xia, M., & Sanjayan, J. (2016) · Materials & Design · doi:10.1016/j.matdes.2016.07.136 · Cited by 359
On the emergence of 3D printable Engineered, Strain Hardening Cementitious Composites (ECC/SHCC)
Li, V. C., Bos, F. P., Yu, K., McGee, W., Ng, T. Y., Figueiredo, S. C., Nefs, K., Mechtcherine, V., Nerella, V. N., Pan, J., et al. (2020) · Cement and Concrete Research · doi:10.1016/j.cemconres.2020.106038 · Cited by 342
Graphene nanoplatelet-fly ash based geopolymer composites
Ranjbar, N., Mehrali, M., Mehrali, M., Alengaram, U. J., & Jumaat, M. Z. (2015) · Cement and Concrete Research · doi:10.1016/j.cemconres.2015.06.003 · Cited by 341
Life cycle inventories for the production of sodium silicates
Fawer, M., Concannon, M., & Rieber, W. (1999) · The International Journal of Life Cycle Assessment · doi:10.1007/bf02979498 · Cited by 334
Yu, J., Yao, J., Lin, X., Li, H., Lam, J. Y. K., Leung, C. K. Y., Sham, I. M. L., & Shih, K. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2018.02.013 · Cited by 324
Sustainable materials for 3D concrete printing
Bhattacherjee, S., Basavaraj, A. S., Rahul, A. V., Santhanam, M., Gettu, R., Panda, B., Schlangen, E., Chen, Y., Copuroglu, O., Ma, G., et al. (2021) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2021.104156 · Cited by 321
Effect of Alumina Release Rate on the Mechanism of Geopolymer Gel Formation
Hajimohammadi, A., Provis, J. L., & van Deventer, J. S. J. (2010) · Chemistry of Materials · doi:10.1021/cm101151n · Cited by 314
Zhu, B., Pan, J., Nematollahi, B., Zhou, Z., Zhang, Y., & Sanjayan, J. (2019) · Materials & Design · doi:10.1016/j.matdes.2019.108088 · Cited by 305
Zhang, Z., Yang, F., Liu, J.-C., & Wang, S. (2020) · Cement and Concrete Research · doi:10.1016/j.cemconres.2020.106200 · Cited by 305
A systematical review of 3D printable cementitious materials
Lu, B., Weng, Y., Li, M., Qian, Y., Leong, K. F., Tan, M. J., & Qian, S. (2019) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2019.02.144 · Cited by 288
Extrusion and rheology characterization of geopolymer nanocomposites used in 3D printing
Panda, B., Unluer, C., & Tan, M. J. (2019) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2019.107290 · Cited by 285
Rheology of alkali-activated materials: A review
Lu, C., Zhang, Z., Shi, C., Li, N., Jiao, D., & Yuan, Q. (2021) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2021.104061 · Cited by 283
Sharma, R., & Khan, R. A. (2017) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2017.03.031 · Cited by 264
3-D printing of concrete: Beyond horizons
Khan, M. S., Sanchez, F., & Zhou, H. (2020) · Cement and Concrete Research · doi:10.1016/j.cemconres.2020.106070 · Cited by 260
Synthesis and characterization of one-part geopolymers for extrusion based 3D concrete printing
Panda, B., Singh, G. B., Unluer, C., & Tan, M. J. (2019) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2019.02.185 · Cited by 254
Structural failure during extrusion-based 3D printing processes
Wolfs, R. J. M., & Suiker, A. S. J. (2019) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-019-03844-6 · Cited by 244
Alkali-activated slag concrete: Fresh and hardened behaviour
Puertas, F., González-Fonteboa, B., González-Taboada, I., Alonso, M. M., Torres-Carrasco, M., Rojo, G., & Martínez-Abella, F. (2018) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2017.10.003 · Cited by 242
Elastic buckling and plastic collapse during 3D concrete printing
Suiker, A. S. J., Wolfs, R. J. M., Lucas, S. M., & Salet, T. A. M. (2020) · Cement and Concrete Research · doi:10.1016/j.cemconres.2020.106016 · Cited by 241
An integrated design method of Engineered Geopolymer Composite
Ohno, M., & Li, V. C. (2018) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2018.02.001 · Cited by 240
Li, Z., Li, W., & Ma, G. (2020) · Composites Part B Engineering · doi:10.1016/j.compositesb.2020.107796 · Cited by 233
3D-printable engineered cementitious composites (3DP-ECC): Fresh and hardened properties
Yu, K., McGee, W., Ng, T. Y., Zhu, H., & Li, V. C. (2021) · Cement and Concrete Research · doi:10.1016/j.cemconres.2021.106388 · Cited by 229
Ye, J., Cui, C., Yu, J., Yu, K., & Xiao, J. (2021) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2021.108639 · Cited by 228
Alghamdi, H., Nair, S. A. O., & Neithalath, N. (2019) · Materials & Design · doi:10.1016/j.matdes.2019.107634 · Cited by 227
Passuello, A., Rodríguez, E. D., Hirt, E., Longhi, M., Bernal, S. A., Provis, J. L., & Kirchheim, A. P. (2017) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2017.08.007 · Cited by 223
Mechanical properties of layered geopolymer structures applicable in concrete 3D-printing
Al-Qutaifi, S., Nazari, A., & Bagheri, A. (2018) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2018.04.195 · Cited by 218
Mohan, M. K., Rahul, A. V., Van Tittelboom, K., & De Schutter, G. (2021) · Cement and Concrete Research · doi:10.1016/j.cemconres.2020.106258 · Cited by 216
Setting on demand for digital concrete – Principles, measurements, chemistry, validation
Reiter, L., Wangler, T., Anton, A., & Flatt, R. J. (2020) · Cement and Concrete Research · doi:10.1016/j.cemconres.2020.106047 · Cited by 211
Ma, S., Qian, Y., & Kawashima, S. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2018.02.022 · Cited by 204
Alternation of traditional cement mortars using fly ash-based geopolymer mortars modified by slag
Shang, J., Dai, J.-G., Zhao, T.-J., Guo, S.-Y., Zhang, P., & Mu, B. (2018) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2018.08.255 · Cited by 197
Micro-cable reinforced geopolymer composite for extrusion-based 3D printing
Ma, G., Li, Z., Wang, L., & Bai, G. (2019) · Materials Letters · doi:10.1016/j.matlet.2018.09.159 · Cited by 196
Technologies for improving buildability in 3D concrete printing
Muthukrishnan, S., Ramakrishnan, S., & Sanjayan, J. (2021) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2021.104144 · Cited by 195
Ovarlez, G., & Roussel, N. (2007) · Materials and Structures · doi:10.1617/s11527-005-9052-1 · Cited by 195
Ambient temperature cured ‘just-add-water’ geopolymer for 3D concrete printing applications
Bong, S. H., Xia, M., Nematollahi, B., & Shi, C. (2021) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2021.104060 · Cited by 193
Panda, B., Ruan, S., Unluer, C., & Tan, M. J. (2020) · Composites Part B Engineering · doi:10.1016/j.compositesb.2020.107826 · Cited by 192
Properties of metakaolin based geopolymer incorporating calcium carbonate
Aboulayt, A., Riahi, M., Touhami, M. O., Hannache, H., Gomina, M., & Moussa, R. (2017) · Advanced Powder Technology · doi:10.1016/j.apt.2017.06.022 · Cited by 183
Hardening evolution of geopolymers from setting to equilibrium: A review
Ranjbar, N., Kuenzel, C., Spangenberg, J., & Mehrali, M. (2020) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2020.103729 · Cited by 181
Guo, X., Yang, J., & Xiong, G. (2020) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2020.103820 · Cited by 179
Feasibility Study of Developing Green ECC Using Iron Ore Tailings Powder as Cement Replacement
Huang, X., Ranade, R., & Li, V. C. (2012) · Journal of Materials in Civil Engineering · doi:10.1061/(asce)mt.1943-5533.0000674 · Cited by 176
Chougan, M., Hamidreza Ghaffar, S., Jahanzat, M., Albar, A., Mujaddedi, N., & Swash, R. (2020) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2020.118928 · Cited by 175
Muthukrishnan, S., Ramakrishnan, S., & Sanjayan, J. (2020) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2020.120786 · Cited by 173
Güllü, H., Cevik, A., Al-Ezzi, K. M. A., & Gülsan, M. E. (2019) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2018.11.140 · Cited by 171
A mix design methodology of slag and fly ash-based alkali-activated paste
Sun, B., Sun, Y., Ye, G., & Schutter, G. D. (2021) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2021.104368 · Cited by 168
The study of the structure rebuilding and yield stress of 3D printing geopolymer pastes
Zhang, D., Wang, D., Lin, X., & Zhang, T. (2018) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2018.06.233 · Cited by 168
Alnahhal, M. F., Kim, T., & Hajimohammadi, A. (2021) · Cement and Concrete Research · doi:10.1016/j.cemconres.2021.106441 · Cited by 147
Xiang, J., Liu, L., Cui, X., He, Y., Zheng, G., & Shi, C. (2018) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2018.09.209 · Cited by 114
Sun, C., Xiang, J., Xu, M., He, Y., Tong, Z., & Cui, X. (2020) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2020.120986 · Cited by 111
Rheology and microstructure of alkali-activated slag cements produced with silica fume activator
Dai, X., Aydın, S., Yardımcı, M. Y., Lesage, K., & Schutter, G. D. (2021) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2021.104303 · Cited by 101
Sustainability-based decision support framework for choosing concrete mixture proportions
Gettu, R., Pillai, R. G., Santhanam, M., Basavaraj, A. S., Rathnarajan, S., & Dhanya, B. S. (2018) · Materials and Structures · doi:10.1617/s11527-018-1291-z · Cited by 98
Methods of enhancing strength of geopolymer produced from powder-based 3D printing process
Xia, M., & Sanjayan, J. (2018) · Materials Letters · doi:10.1016/j.matlet.2018.05.100 · Cited by 89
Ma, G., Zhang, J., Li, W., Li, Z., & Sun, J. (2018) · Smart Materials and Structures · doi:10.1088/1361-665x/aac789 · Cited by 85
Alrefaei, Y., Wang, Y., & Dai, J. (2021) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2020.103917 · Cited by 83
From casting to 3D printing geopolymers: A proof of concept
Voney, V., Odaglia, P., Brumaud, C., Dillenburger, B., & Habert, G. (2021) · Cement and Concrete Research · doi:10.1016/j.cemconres.2021.106374 · Cited by 59
Effects of mixing duration on engineering properties of geopolymer concrete
Mahmood, A. H., Foster, S. J., & Castel, A. (2021) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2021.124449 · Cited by 58
Feys, D., & Asghari, A. A. (2019) · Cement and Concrete Research · doi:10.1016/j.cemconres.2018.12.003 · Cited by 51
Jelić, T. A., Čiẑmek, A., Kosanović, C., & Subotić, B. (1993) · Journal of the Chemical Society Faraday Transactions · doi:10.1039/ft9938901817 · Cited by 50
Nematollahi, B., Xia, M., & Sanjayan, J. (2019) · Frontiers in Materials · doi:10.3389/fmats.2019.00160 · Cited by 40
Metadata
- Authors
- Zhong, H., & Zhang, M.
- Venue
- Cement and Concrete Composites
- Publisher
- Elsevier BV
- Published
- 2022-04
- Volume
- 128
- Pages
- 104455
- ISSN
- 0958-9465 (ISSN-L)
- OpenAlex
- W4213334403
- Cited by
- 176
- References
- 102
- FWCI
- 14.14
- Type
- journal article
- Language
- en
- Open access
- hybrid
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.