Modelling of frost growth and densification
Integrity signals
Registry
Cites
Statistics
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
Most experimental tests have been conducted on horizontally assembled plates or fin-and-tube heat exchangers under horizontal air flow conditions.
“In addition, most experimental tests have been con ducted on horizontally assembled plates [12 -17] or fin-and-tube heat exchangers under horizontal air flow conditions [18 -21].”
Structural changes in the frost layer during permeation tend to increase both frost density and thermal conductivity with time.
“This will result in structural changes in the frost layer that tends to increase both the frost density and thermal conductivity with time.”
From Studies of an air cooler under frost condition (2019) · cites this paper as Le Gall et al. (1997)
Only Sherif et al. (1993) and Le Gall et al. (1997) proposed models to account for the frost characteristic of partial melting and refreezing that occurs when the frost surface reaches 0 °C (permeation).
“While many research efforts have proposed different models of frost growth, only Sherif et al. (1993) and Le Gall et al. (1997) proposed model to account for the frost characteristic of partial melting and refreezing that occurs when the frost surface reaches 0 o C, which is known as permeation process.”
From Studies of an air cooler under frost condition (2019) · cites this paper as Le Gall et al. (1997)
During permeation, the frost layer undergoes a cycle of thinning and densification due to melting and subsequent formation on an icy sub layer at the top of the deposit.
“During this period, the frost layer undergoes a cycle of thinning and densification due to the melting and subsequent formation on an icy sub layer at the top of the deposit.”
From Studies of an air cooler under frost condition (2019) · cites this paper as Le Gall et al. (1997)
The 'hand-to-hand' diffusion process could increase the effective diffusivity in frost.
“This so-called 'hand-to-hand' diffusion process, already reported for the snow case (Le Gall and Grillot, 1997), could increase the effective diffusivity.”
From Frosting modeling on a cold flat plate: Comparison of the different assumptions and impacts on frost growth predictions (2016) · cites this paper as Le Gall and Grillot, 1997
The main approach in the literature is to develop models based on heat and mass diffusion through the frost layer considered as a porous solid.
“Finally, the main approach is to develop models based on heat and mass diffusion through the frost layer considered as a porous solid (Jones and Parker, 1975; Kondepudi and O'Neal, 1993; Le Gall and Grillot, 1997; Lee et al., 1997; Na and Webb, 2004a).”
From Frosting modeling on a cold flat plate: Comparison of the different assumptions and impacts on frost growth predictions (2016) · cites this paper as Le Gall and Grillot, 1997
Frost formation on flat plate and cylindrical surfaces is relatively well known and can be predicted reliably with existing models and correlations.
“Therefore, frost formation on flat plate and cylindrical surface is relatively well known and can be predicted reliably with existing models and correlations.”
From Modeling for predicting frosting behavior of a fin–tube heat exchanger (2006) · cites this paper as [8]
Water-vapor transport through a porous medium is mainly due to Fickian diffusion caused by the gradient of the vapor partial pressure.
“Previous researchers assumed that the water-vapor at the frost surface is saturated with the surface temperature, and water-vapor transport through a porous medium is mainly due to Fickian diffusion caused by the gradient of the vapor partial pressure [4,11,13,14].”
From Analysis of the frost growth on a flat plate by simple models of saturation and supersaturation (2005) · cites this paper as [11]
Le Gall and Grillot set the frost surface density at a fixed value of 25 kg/m3 but did not justify use of this value.
“Le Gall and Grillot [6] set the frost surface density at a fixed value (25 kg/m 3 ), but did not justify use of this value.”
From New model for frost growth rate (2004) · cites this paper as [6]
Tao et al. [10] and Le Gall and Grillot [6] used a saturation model and adjusted the tortuosity factor to force agreement of their model predictions to experimental data, resulting in a tortuosity factor greater than 1.0.
“Tao et al. [10] and Le Gall and Grillot [6] used a saturation model and compared their predicted results to their experimental data. They adjusted the tortuosity factor to force agreement of their model predictions to the experimental data. This resulted in a tortuosity factor greater than 1.0”
From New model for frost growth rate (2004) · cites this paper as [6]
Cites
Numerical Heat Transfer and Fluid Flow
Patankar, S. V. (2018) · CRC Press eBooks · doi:10.1201/9781482234213 · Cited by 23,406 · see citing works
Numerical Heat Transfer and Fluid Flow
Hsu, C. (1981) · Nuclear Science and Engineering · doi:10.13182/nse81-a20112 · Cited by 15,200 · see citing works
Levenspiel, O. (1999) · Industrial & Engineering Chemistry Research · doi:10.1021/ie990488g · Cited by 10,011 · see citing works
Hartnett, J. P., Irvine, T. F., Cho, Y. I., & Greene, G. A. (2003) · CERN Document Server (European Organization for Nuclear Research) · Cited by 1,560 · see citing works
Simultaneous Heat, Mass, and Momentum Transfer in Porous Media: A Theory of Drying
Whitaker, S. (1977) · Advances in heat transfer · doi:10.1016/s0065-2717(08)70223-5 · Cited by 1,156 · see citing works
Hinrichsen, O., & Klemm, E. (2016) · Chemical Engineering & Technology · doi:10.1002/ceat.201690063 · Cited by 862 · see citing works
Study of frost properties correlating with frost formation types
Hayashi, Y., Aoki, A., Adachi, S., & Hori, K. (1977) · Journal of Heat Transfer · doi:10.1115/1.3450675 · Cited by 402 · see citing works
A mathematical model for predicting the densification and growth of frost on a flat plate
Tao, Y.-X., Besant, R. W., & Rezkallah, K. S. (1993) · International Journal of Heat and Mass Transfer · doi:10.1016/0017-9310(93)80011-i · Cited by 183 · see citing works
Frost formation with varying environmental parameters
Jones, B. W., & Parker, J. D. (1975) · Journal of Heat Transfer · doi:10.1115/1.3450350 · Cited by 171 · see citing works
Frost deposition on cold surfaces
Brian, P. L. T., Reid, R. C., & Shah, Y. T. (1970) · Industrial & Engineering Chemistry Fundamentals · doi:10.1021/i160035a013 · Cited by 142 · see citing works
Effective Thermal Conductivity of Frost
Auracher, H. (1986) · Proceeding of International Symposium on Heat and Mass Transfer in Refrigeration and Cryogenics · doi:10.1615/ichmt.1986.intsymphmtinrefcryo.210 · Cited by 68 · see citing works
Simultaneous Heat and Mass Transfer Accompanied by Phase Change in Porous Insulation
Vafai, K., & Whitaker, S. (1986) · ASME Journal of Heat and Mass Transfer · doi:10.1115/1.3246877 · Cited by 60 · see citing works
Incipient Phenomena of Frost Formation
Seki, N., FUKUSAKO, S., MATSUO, K., & UEMURA, S. (1984) · Bulletin of JSME · doi:10.1299/jsme1958.27.2476 · Cited by 33 · see citing works
Unsteady heat and mass transfer with phase changes in an insulation slab: frosting effects
Tao, Y.-X., BESANT, R. W., & REZKALLAH, K. S. (1991) · International Journal of Heat and Mass Transfer · doi:10.1016/0017-9310(91)90139-6 · Cited by 32 · see citing works
Tao, Y.-X., & BESANT, R. W. (1993) · ASME Journal of Heat and Mass Transfer · doi:10.1115/1.2910665 · Cited by 19 · see citing works
Frost formation: The influence of frost formation and defrosting on the performance of air coolers
Sanders, C. T. (1974) · Research Repository (Delft University of Technology) · Cited by 18 · see citing works
(1969) · DSpace@MIT (Massachusetts Institute of Technology) · Cited by 18 · see citing works
Aoki, K., KATAYAMA, K., & Hayashi, Y. (1983) · Bulletin of JSME · doi:10.1299/jsme1958.26.87 · Cited by 17 · see citing works
HEAT TRANSFER IN FROST AND SNOW
Auracher, H. (1978) · International Heat Transfer Conference (IHTC) · doi:10.1615/ihtc6.510 · Cited by 9 · see citing works
Flagged first, then by citations
2 of the 21 references couldn’t be matched to a known paper.
Cited by
Sorted by citations
Surface engineering for phase change heat transfer: A review
Attinger, D., Frankiewicz, C., Betz, A. R., Schutzius, T. M., Ganguly, R., Das, A., Kim, C.-J., & Megaridis, C. M. (2014) · MRS Energy & Sustainability · doi:10.1557/mre.2014.9 · Cited by 396 · see citing works
Surface engineering for phase change heat transfer: A review
Attinger, D., Frankiewicz, C., Betz, A. R., Schutzius, T. M., Ganguly, R., Das, A., Kim, C., & Megaridis, C. M. (2014) · reroDoc Digital Library · Cited by 227 · see citing works
A fundamental understanding of factors affecting frost nucleation
Na, B., & Webb, R. L. (2003) · International Journal of Heat and Mass Transfer · doi:10.1016/s0017-9310(03)00194-7 · Cited by 225 · see citing works
A Review of Condensation Frosting
Nath, S., Ahmadi, S., & Boreyko, J. B. (2017) · Nanoscale and Microscale Thermophysical Engineering · doi:10.1080/15567265.2016.1256007 · Cited by 200 · see citing works
Review on the measurement and calculation of frost characteristics
Song, M., & Dang, C. (2018) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2018.03.094 · Cited by 212 · see citing works
New model for frost growth rate
Na, B., & Webb, R. L. (2004) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2003.09.001 · Cited by 210 · see citing works
Prediction of the frost formation on a cold flat surface
Lee, K.-S., Jhee, S., & Yang, D.-K. (2003) · International Journal of Heat and Mass Transfer · doi:10.1016/s0017-9310(03)00195-9 · Cited by 190 · see citing works
On Localized Vapor Pressure Gradients Governing Condensation and Frost Phenomena
Nath, S., & Boreyko, J. B. (2016) · Langmuir · doi:10.1021/acs.langmuir.6b01488 · Cited by 155 · see citing works
Hydrate Formation in Gas-Dominant Systems Using a Single-Pass Flowloop
Lorenzo, M. D., Aman, Z. M., Soto, G. S., Johns, M. L., Kozielski, K. A., & May, E. F. (2014) · Energy & Fuels · doi:10.1021/ef500361r · Cited by 149 · see citing works
Frost growth and densification in laminar flow over flat surfaces
Kandula, M. (2011) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2011.02.056 · Cited by 141 · see citing works
Mass transfer on and within a frost layer
Na, B., & Webb, R. L. (2004) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2003.08.023 · Cited by 129 · see citing works
Gas Hydrate Deposition on a Cold Surface in Water-Saturated Gas Systems
Rao, I., Koh, C. A., Sloan, E. D., & Sum, A. K. (2013) · Industrial & Engineering Chemistry Research · doi:10.1021/ie400493a · Cited by 124 · see citing works
Shin, J., Tikhonov, A. V., & Kim, C. (2003) · Journal of Heat Transfer · doi:10.1115/1.1518496 · Cited by 123 · see citing works
Frosting model for predicting macroscopic and local frost behaviors on a cold plate
Kim, D., Kim, C., & Lee, K.-S. (2015) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2014.11.048 · Cited by 103 · see citing works
State-of-the-art review of frost deposition on flat surfaces
Léoni, A., Mondot, M., Durier, F., Revellin, R., & Haberschill, P. (2016) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2016.04.004 · Cited by 103 · see citing works
Analysis of the frost growth on a flat plate by simple models of saturation and supersaturation
Lee, Y. B., & Ro, S. T. (2005) · Experimental Thermal and Fluid Science · doi:10.1016/j.expthermflusci.2004.11.001 · Cited by 100 · see citing works
Sommers, A. D., Gebhart, C. W., & Hermes, C. J. L. (2018) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2018.01.074 · Cited by 100 · see citing works
Frost formation on a vertical plate in simultaneously developing flow
Lee, Y. B., & Ro, S. T. (2002) · Experimental Thermal and Fluid Science · doi:10.1016/s0894-1777(02)00216-9 · Cited by 97 · see citing works
Modeling for predicting frosting behavior of a fin–tube heat exchanger
Yang, D.-K., Lee, K.-S., & Song, S. (2006) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2005.09.022 · Cited by 94 · see citing works
Transient two-dimensional model of frost formation on a fin-and-tube heat exchanger
Lenic, K., Trp, A., & Frankovic, B. (2009) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2008.06.005 · Cited by 92 · see citing works
<i>Review Article:</i> A Critical Review of Properties and Models for Frost Formation Analysis
Iragorry, J., Tao, Y.-X., & Jia, S. (2004) · HVAC&R Research · doi:10.1080/10789669.2004.10391111 · Cited by 89 · see citing works
Sommers, A. D., Truster, N. L., Napora, A. C., Riechman, A. C., & Caraballo, E. J. (2016) · Experimental Thermal and Fluid Science · doi:10.1016/j.expthermflusci.2016.01.008 · Cited by 84 · see citing works
Capillary Balancing: Designing Frost-Resistant Lubricant-Infused Surfaces
Wong, W. S. Y., Hegner, K. I., Donadei, V., Hauer, L., Naga, A., & Vollmer, D. (2020) · Nano letters (Print) · doi:10.1021/acs.nanolett.0c02956 · Cited by 76 · see citing works
Zhang, L., Song, M., Deng, S., Shen, J., & Dang, C. (2022) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2022.118984 · Cited by 83 · see citing works
Fin spacing optimization of a fin-tube heat exchanger under frosting conditions
Yang, D.-K., Lee, K.-S., & Song, S. (2006) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2006.01.016 · Cited by 81 · see citing works
Air-side heat transfer enhancement of a refrigerator evaporator using vortex generation
Sommers, A., & Jacobi, A. (2005) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2005.04.003 · Cited by 89 · see citing works
A mathematical model for frost growth and densification on flat surfaces
ElCheikh, A., & Jacobi, A. M. (2014) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2014.05.054 · Cited by 77 · see citing works
Modeling of frosting behavior on a cold plate
Yang, D.-K., & Lee, K.-S. (2005) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2004.08.001 · Cited by 77 · see citing works
Léoni, A., Mondot, M., Durier, F., Revellin, R., & Haberschill, P. (2017) · Experimental Thermal and Fluid Science · doi:10.1016/j.expthermflusci.2017.06.005 · Cited by 74 · see citing works
Frost formation on a cold surface under turbulent flow
Yang, D.-K., Lee, K.-S., & Cha, D.-J. (2006) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2005.07.003 · Cited by 75 · see citing works
Brèque, F., & Nemer, M. (2016) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2016.06.010 · Cited by 70 · see citing works
Ye, H.-Y., & Lee, K.-S. (2013) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2013.08.026 · Cited by 70 · see citing works
A semi-empirical correlation for the frost density
Hermes, C. J. L., Loyola, F. R., & Nascimento, V. S. (2014) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2014.02.008 · Cited by 69 · see citing works
Modeling of frost formation over parallel cold plates considering a two-dimensional growth rate
Armengol, J. M., Salinas, C. T., Xamán, J., & Ismail, K. A. R. (2016) · International Journal of Thermal Sciences · doi:10.1016/j.ijthermalsci.2016.01.017 · Cited by 69 · see citing works
Hydrate Deposition on Cold Pipe Walls in Water-in-Oil (W/O) Emulsion Systems
Ding, L., Shi, B., Wang, J., Liu, Y., Lv, X., Wu, H., Wang, W., Lou, X., & Gong, J. (2017) · Energy & Fuels · doi:10.1021/acs.energyfuels.7b00559 · Cited by 56 · see citing works
Modeling of frost layer growth considering frost porosity
Lee, J., Kim, J., Kim, D. R., & Lee, K.-S. (2018) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2018.05.098 · Cited by 52 · see citing works
Effective thermal conductivity of frost during the crystal growth period
Şahin, A. Z. (2000) · International Journal of Heat and Mass Transfer · doi:10.1016/s0017-9310(99)00162-3 · Cited by 53 · see citing works
Thermofluid characteristics of frosted finned-tube heat exchangers
Yan, W.-M., Li, H.-Y., & Tsay, Y.-L. (2005) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2005.02.018 · Cited by 52 · see citing works
Numerical simulation of frosting behavior and its effect on a direct-contact ambient air vaporizer
Kuang, Y.-W., Yi, C., & Wang, W. (2015) · Journal of Natural Gas Science and Engineering · doi:10.1016/j.jngse.2015.06.042 · Cited by 45 · see citing works
Transient model of a vertical freezer with door openings and defrost effects
Mastrullo, R., Mauro, A. W., Menna, L., Palma, A., & Vanoli, G. (2014) · Applied Energy · doi:10.1016/j.apenergy.2014.01.069 · Cited by 45 · see citing works
Liu, X., Yu, J., & Yan, G. (2020) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2019.114634 · Cited by 47 · see citing works
Kim, K.-H., Ko, H.-J., Kim, K., Kim, Y.-W., & Cho, K.-J. (2009) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2008.10.015 · Cited by 47 · see citing works
(2015) · doi:10.1016/j.expthermflusci.2014.10.006 · Cited by 47 · see citing works
Microchannel Heat Exchanger Design for Evaporator and Condenser Applications
Kim, M.-H., Lee, S.-Y., Mehendale, S., & Webb, R. (2003) · Advances in heat transfer · doi:10.1016/s0065-2717(03)37004-2 · Cited by 45 · see citing works
Hwang, J., & Cho, K. (2014) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2014.04.026 · Cited by 44 · see citing works
Review on frosting, defrosting and frost management techniques in industrial food freezers
Badri, D., Toublanc, C., Rouaud, O., & Michel Havet, C. (2021) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2021.111545 · Cited by 43 · see citing works
Klingebiel, J., Hassan, M., Venzik, V., Vering, C., & Müller, D. (2023) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2023.121072 · Cited by 44 · see citing works
A Semi-Empirical Model for Predicting Frost Properties
Li, S.-M., Yang, K., & Wang, C. (2021) · Processes · doi:10.3390/pr9030412 · Cited by 42 · see citing works
Klingebiel, J., Salamon, M., Bogdanov, P., Venzik, V., Vering, C., & Müller, D. (2023) · Energy and Buildings · doi:10.1016/j.enbuild.2023.113397 · Cited by 32 · see citing works
Study of the thermal behavior of a latent heat cold storage unit operating under frosting conditions
Simard, A., & Lacroix, M. (2003) · Energy Conversion and Management · doi:10.1016/s0196-8904(02)00183-8 · Cited by 40 · see citing works
Lenic, K., Trp, A., & Frankovic, B. (2009) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2008.12.030 · Cited by 38 · see citing works
Tahavvor, A., & Yaghoubi, M. (2010) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2010.06.004 · Cited by 35 · see citing works
Sommers, A. D., Napora, A. C., Truster, N. L., Caraballo, E. J., & Hermes, C. J. L. (2016) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2016.10.025 · Cited by 33 · see citing works
Nicholas, J. W., Koh, C. A., & Sloan, E. D. (2009) · AIChE Journal · doi:10.1002/aic.11921 · Cited by 32 · see citing works
Frost formation and heat transfer on a cold surface in ice fog
Mago, P. J., & Sherif, S. A. (2004) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2004.10.004 · Cited by 32 · see citing works
Mechanisms of trace water vapor frosting on a cryogenic surface in nitrogen gas flow
Qi, Y., Zhi, X., Zhang, H., Wang, K., & Qiu, L. (2021) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2021.120898 · Cited by 31 · see citing works
A semi-empirical model for predicting frost accretion on hydrophilic and hydrophobic surfaces
Hermes, C., Sommers, A., Gebhart, C. W., & Nascimento, V. (2017) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2017.09.022 · Cited by 31 · see citing works
Evaporator Frosting in Refrigerating Appliances: Fundamentals and Applications
Hermes, C., Boeng, J., da Silva, D. D., Knabben, F. T., & Sommers, A. (2021) · Energies · doi:10.3390/en14185991 · Cited by 26 · see citing works
Benítez, T., & Sherif, S. A. (2017) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2017.01.026 · Cited by 27 · see citing works
Iranagh, S. A., Tahavvor, A., Yaghoubi, M., & Tavakol, M. (2021) · International Communications in Heat and Mass Transfer · doi:10.1016/j.icheatmasstransfer.2021.105556 · Cited by 22 · see citing works
A finite volume method to solve the frost growth using dynamic meshes
Bartrons, E., Oliet, C., Gutiérrez, E., Naseri, A., & Perez-Segarra, C. (2018) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2018.03.104 · Cited by 28 · see citing works
Fixed grid numerical modelling of frost growth and densification
Bartrons, E., Galione, P., & Perez-Segarra, C. (2019) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2018.10.080 · Cited by 24 · see citing works
Experimental Characterization of Frost Growth on a Horizontal Plate Under Natural Convection
Niroomand, S., Fauchoux, M., & Simonson, C. (2018) · Journal of Thermal Science and Engineering Apllications · doi:10.1115/1.4040989 · Cited by 23 · see citing works
Measurements of Frost Thickness and Frost Mass on a Flat Plate under Heat Pump Condition
Yoon, S., HAYASE, G., & Cho, K. (2010) · Heat Transfer Engineering · doi:10.1080/01457631003638911 · Cited by 23 · see citing works
Modeling of a fan-supplied flat-tube heat exchanger exposed to non-uniform frost growth
Breque, F., & Nemer, M. (2017) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2016.12.012 · Cited by 21 · see citing works
Analysis of early-stage frost formation in natural convection over a horizontal cylinder
Tahavvor, A., & Yaghoubi, M. (2009) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2009.02.002 · Cited by 22 · see citing works
Ren, L.-M., Jiao, W., Tian, G., Tian, X.-H., & Liu, S.-S. (2021) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2021.04.035 · Cited by 15 · see citing works
Liang, X.-Y., & Wu, L. (2022) · Energy and Buildings · doi:10.1016/j.enbuild.2022.112366 · Cited by 18 · see citing works
A lattice Boltzmann study of frost growth on a cold surface
Gong, J., Hou, J., Li, G., Gao, T.-Y., & Sun, J.-J. (2018) · International Communications in Heat and Mass Transfer · doi:10.1016/j.icheatmasstransfer.2018.08.012 · Cited by 17 · see citing works
General correlation for frost thermal conductivity on parallel surface channels
Hosseini, S. H., Valizadeh, M., Zendehboudi, A., & Song, M. (2020) · Energy and Buildings · doi:10.1016/j.enbuild.2020.110282 · Cited by 17 · see citing works
Ye, H.-Y., Park, J., & Lee, K.-S. (2014) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2014.08.069 · Cited by 17 · see citing works
Analysis of Thermal Conductivity of Frost on Cryogenic Finned-tube Vaporizer Using Fractal Method
Chen, S.-P., Yao, S.-T., & Xie, F.-S. (2013) · Energy and Power Engineering · doi:10.4236/epe.2013.54b021 · Cited by 13 · see citing works
Schmiesing, N. C., & Sommers, A. D. (2017) · Science and Technology for the Built Environment · doi:10.1080/23744731.2017.1333876 · Cited by 17 · see citing works
Deutz, K. R., Charles, G.-L., Cauret, O., Rullière, R., & Haberschill, P. (2018) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2018.05.022 · Cited by 17 · see citing works
Generalized lattice Boltzmann model for frosting.
Lei, T.-M., Luo, K. H., & Wu, D. (2019) · Physical Review E · doi:10.1103/physreve.99.053301 · Cited by 11 · see citing works
Free convection frost growth in a narrow vertical channel
Tanda, G., & Fossa, M. (2006) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2005.11.010 · Cited by 14 · see citing works
Frost Growth in Regenerative Wheels
Shang, W., Chen, H., & Besant, R. (2005) · ASME Journal of Heat and Mass Transfer · doi:10.1115/1.2005274 · Cited by 14 · see citing works
Effect of Moisture Transfer Through a Semipermeable Membrane on Condensation/Frosting Limit
Niroomand, S., Fauchoux, M. T., & Simonson, C. J. (2018) · Journal of Heat Transfer · doi:10.1115/1.4041185 · Cited by 14 · see citing works
Bai, X., Liu, S., Deng, S., Zhang, L., & Wei, M. (2022) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2022.119933 · Cited by 13 · see citing works
Critical operating conditions for prevention of frost formation in fin-tube heat exchangers
Ye, H.-Y., Park, J.-S., & Lee, K.-S. (2014) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2014.04.044 · Cited by 13 · see citing works
Westhaeuser, J., Schulze, C., Albrecht, J.-C., Tegethoff, W., Lemke, N., & Koehler, J. (2023) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2023.120140 · Cited by 12 · see citing works
Modeling of Frost Growth on Heat Exchanger Surfaces
Schmitz, G. (2006) · Cited by 12 · see citing works
Inan, C., Newell, T. A., & Eǧrican, A. N. (2000) · Illinois Digital Environment for Access to Learning and Scholarship (University of Illinois at Urbana-Champaign) · Cited by 11 · see citing works
Hattori, A., Sato, T., Himeno, T., & Watanabe, T. (2024) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2024.126321 · Cited by 10 · see citing works
Evaluation of the frost properties on a semipermeable membrane
Niroomand, S., Fauchoux, M. T., & Simonson, C. J. (2019) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2018.12.116 · Cited by 10 · see citing works
Juhola, V., Mikkola, V., Inkeri, E., Kabelac, S., & Tynjälä, T. (2025) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2025.127396 · Cited by 9 · see citing works
Modeling Frost Formation Within a Commercial 3-D CFD Code
Ellgas, S., & Pfitzner, M. (2007) · Numerical Heat Transfer Part A Applications · doi:10.1080/10407780701678224 · Cited by 9 · see citing works
Clumping of frozen par-fried foods: Lessons from frosting on structured surfaces
van der Sman, R. V. D. (2018) · Food Structure · doi:10.1016/j.foostr.2018.06.001
Heat transfer — a review of 1997 literature
Eckert, E. R. G., Goldstein, R. J., Ibele, W. E., Patankar, S. V., Simon, T., Kuehn, T. H., Strykowski, P. J., Tamma, K. K., Bar‐Cohen, A., Heberlein, J. V. R., et al. (2000) · International Journal of Heat and Mass Transfer · doi:10.1016/s0017-9310(99)00196-9 · Cited by 9 · see citing works
Accelerated Cryogenic Cooling Caused by the Temporary Frost Layer Enhancer
Mazor, G., Ladizhensky, I., Nemirovsky, D., Alfi, A., Rabin, A., Yehud, E., & Korin, E. (2016) · ASME Journal of Heat and Mass Transfer · doi:10.1115/1.4034899 · Cited by 9 · see citing works
Benítez, T., Sherif, S., & Benitez, J. (2019) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2019.02.005 · Cited by 8 · see citing works
Study on Transient Distributed Model of Frost on Heat Pump Evaporator
Liu, Z., Zhu, H., & Wang, H. (2005) · Journal of Asian Architecture and Building Engineering · doi:10.3130/jaabe.4.265 · Cited by 8 · see citing works
Prediction of heat and mass transfer inside 3D frost microstructure
Mao, N., Nishimura, K., Gong, J., Takayashiki, M., Ściążko, A., Komatsu, Y., Tang, J., & Shikazono, N. (2024) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2024.122978 · Cited by 7 · see citing works
Variation of Frost Roughness on a Flat Plate Under Forced Convection
Zhang, T., O'Neal, D., & McClain, S. (2021) · Journal of Thermal Science and Engineering Applications · doi:10.1115/1.4047570 · Cited by 7 · see citing works
Simulation of Forced Convection Frost Formation in Microtubule Bundles at Ultra-Low Temperature
Mi, Y., Liu, M., Wu, H., Wang, J., & Zhao, R.-K. (2022) · Aerospace · doi:10.3390/aerospace9100630 · Cited by 5 · see citing works
Frost Formation: Optimizing solutions under a finite volume approach
Bartrons, E., Segarra, C. D. P., & Oliet, C. (2016) · Journal of Physics Conference Series · doi:10.1088/1742-6596/745/3/032062 · Cited by 5 · see citing works
A Numerical Investigation of Frost Growth on Cold Surfaces Based on the Lattice Boltzmann Method
Gong, J., Hou, J., Sun, J.-J., Li, G., & Gao, T.-Y. (2018) · Energies · doi:10.3390/en11082077 · Cited by 3 · see citing works
A Climatic Facility and Apparatus for Investigations of Cold Soaked Fuel Frost Evolution
McClain, S. T., Zhang, T., Ahmed, S., Stafford, G. J., Cornejo, J. A., & O’Neal, D. L. (2020) · AIAA AVIATION Forum · doi:10.2514/6.2020-2808 · Cited by 5 · see citing works
Frost Formation and Heat Transfer on a Cold Surface in Ice Fog
Mago, P. J., & Sherif, S. A. (2004) · AIAA Aerospace Sciences Meeting and Exhibit · doi:10.2514/6.2004-164 · Cited by 5 · see citing works
A non-iterative solution for frost growth on flat surfaces
Hollon, D., Truster, N., Byrd, L., Roman, A. J., & Wolff, M. (2023) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2023.124578 · Cited by 5 · see citing works
- Authors
- Le Gall, R., Grillot, J. M., & Jallut, C.
- Affiliations
- CEA Grenoble (FR)
- Lyon 1 Université (FR)
- ORCID
- Jallut, C.
- Venue
- International Journal of Heat and Mass Transfer
- Publisher
- Elsevier BV
- Published
- 1997-09
- Volume
- 40
- Issue
- 13
- Pages
- 3177-3187
- ISSN
- 0017-9310 (ISSN-L)
- OpenAlex
- W2012124706
- Cited by
- 153
- References
- 21
- Citations by year
- 2026: 7 · 2025: 6 · 2024: 5 · 2023: 6 · 2022: 4 · 2021: 10 · 2020: 6 · 2019: 4 · 2018: 15 · 2017: 8 · 2016: 10 · 2015: 2 · 2014: 15 · 2013: 5 · 2012: 1
- FWCI
- 3.69
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- International Journal of Heat and Mass Transfer (publishedVersion)
- HAL (submittedVersion)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Refrigeration and Air Conditioning Technologies
- Physical Sciences › Engineering › Computational Mechanics › Heat and Mass Transfer in Porous Media
- Physical Sciences › Engineering › Mechanical Engineering › Adsorption and Cooling Systems
- Keywords
- frost growth, frost layer, cold wall, volume averaging, one-dimensional transient model
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
