Power Cycling Reliability of Power Module: A Survey
Open accessThe DOI matches its Crossref record; 91 of the 94 references it cites were found in a registry or an index.
Abstract
Electronic devices using semiconductors such as insulated-gate bipolar transistors, metal-oxide-semiconductor field-effect transistors, and diodes are extensively used in electrical traction applications such as locomotive, elevators, subways, and cars. The long-term reliability of such power modules is then highly demanded, and their main reliability criterion is their power cycling capability. Thus, a power cycling test is the most important reliability test for power modules. This test consists in periodically applying a current to a device mounted onto a heat sink. This leads to power loss in the entire module and results in a rise in the semiconductor temperature. In this paper, the different kinds of semiconductors and power modules used for traction applications are described. Experimental and simulation methods employed for power cycling tests are presented. Modules' weak points and fatigue processes are pointed out. Then, a detailed statistical review of publications from 1994 to 2015 dealing with power cycling is presented. This review gives a clear overview of all studies dealing with power cycling that were carried out until now. It reveals the principal trends in power electronic devices and highlights the main reliability issues for which an important lack of knowledge remains.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The text we found for this paper looks like another document, so the self-check wasn’t run.
Citations
Cites
Comparison of 6H-SiC, 3C-SiC, and Si for power devices
Bhatnagar, M., & Baliga, B. J. (1993) · IEEE Transactions on Electron Devices · doi:10.1109/16.199372 · Cited by 1,120
Selected failure mechanisms of modern power modules
Ciappa, M. (2002) · Microelectronics Reliability · doi:10.1016/s0026-2714(02)00042-2 · Cited by 1,039 · cited 2×
“Bond wires are often reported as the weakest component of power modules, responsible for device failures [15], [16], [37].”
BackgroundSemiconductor Power Devices: Physics, Characteristics, Reliability
Lutz, J., Schlangenotto, H., Scheuermann, U., & De Doncker, R. (2011) · Springer eBooks · doi:10.1007/978-3-642-11125-9 · Cited by 706
Ageing and Failure Modes of IGBT Modules in High-Temperature Power Cycling
Smet, V., Forest, F., Huselstein, J.-J., Richardeau, F., Khatir, Z., Lefebvre, S., & Berkani, M. (2011) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2011.2114313 · Cited by 620
Fast power cycling test of IGBT modules in traction application
Held, M., Jacob, P., Nicoletti, G., Scacco, P., & Poech, M.-H. (2002) · Proceedings of Second International Conference on Power Electronics and Drive Systems · doi:10.1109/peds.1997.618742 · Cited by 585
(2008) · Cited by 578
Reliability of power cycling for igbt power semiconductor modules
Morozumi, A., Yamada, K., Miyasaka, T., Sumi, S., & Seki, Y. (2003) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2003.810661 · Cited by 256
Smet, V., Forest, F., Huselstein, J.-J., Rashed, A., & Richardeau, F. (2013) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2012.2196894 · Cited by 232
Power cycling induced failure mechanisms in solder layers
Herrmann, T., Feller, M., Lutz, J., Bayerer, R., & Licht, T. (2007) · 2007 European Conference on Power Electronics and Applications · doi:10.1109/epe.2007.4417702 · Cited by 116
Hamidi, A., Beck, N., Thomas, K., & Herr, E. (1999) · Microelectronics Reliability · doi:10.1016/s0026-2714(99)00164-x · Cited by 106
Research works printed but not linked: 17
- liew, 0, Electromigration interconnect lifetime under AC and pulsed DC stress, Proc IEEE 27th Int Rel Symp, 215
- 2010, Halbleiterbauelemente—Mechanische und klimatische Prüfverfahren—Teil 34 Lastwechselprüfung
- 2013, Environmental test methods for semiconductor devices Part 1 Test methods 1000 through 1999
- 2007, Power Cycling
- khong, 2007, Fiabilité Prédictive de Composants de Puissance Soumis a des Tests de Fatigue Accélérée
- scheuermann, 0, Power cycling lifetime of advanced power modules for different temperature swings, Proc PCIM Eur, 59
- ong, 0, Heavy Al ribbon interconnect: An alternative solution for hybrid power packaging, Proc IMAPS Int J Microcircuits Electron Packag, 1
- guth, 0, New assembly and interconnects beyond sintering methods, Proc PCIM, 1
- stupar, 0, Lifetime model for solder layers, Proc ECPE Workshop, 1
- böttcher, 0, Laboratory setup for power cycling of IGBT modules with monitoring of ON-state voltage and thermal resistance for state of aging detection, Proc Int Exhib Conf Power Electron Intell Motion Renew Energy Manage PCIM, 1
- hutzler, 2014, Power Cycling Community 1995–2014, Bodo's Power Syst, 2014, 78
- thoben, 0, Modelling and experimental investigations on degradation of microcomponents in power cycling, Proc Ansys Paper, 1
- farassat, 2007, More performance at lower cost—Heavy aluminium ribbon bonding, 1
- 2014, Data sheet for power discrete device SO8-FL
- benzler, 0, New module generation for higher lifetime, Proc Bodo's Power Syst, 30
- jacques, 2010, Etude de la Fatigue Thermomécanique des Composants de Puissance de Type TRIAC Soumis a des Cycles Actifs de Températures
- bouarroudj-berkani, 2008, Etude de la thermo-mécanique de modules electroniques de puissance en ambiance de températures elevées pour des applications de traction de véhicules electriques et hybrides
Cited by
A Review of SiC Power Module Packaging Technologies: Challenges, Advances, and Emerging Issues
Lee, H., Smet, V., & Tummala, R. (2020) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2019.2951801 · Cited by 526
“conventional power module package are wire bond lift-off, cracking or delamination of solder die (or substrate) attach, and chip metallization on the top side [37], [38].”
BackgroundOverview of Real-Time Lifetime Prediction and Extension for SiC Power Converters
Ni, Z., Lyu, X., Yadav, O. P., Singh, B. N., Zheng, S., & Cao, D. (2020) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2019.2962503 · Cited by 261
“Thus, Rth_jc could be used as an indicator of the solder layer failures [113].”
Reliability of Power Electronic Systems for EV/HEV Applications
Blaabjerg, F., Wang, H., Vernica, I., Liu, B., & Davari, P. (2021) · Proceedings of the IEEE · doi:10.1109/jproc.2020.3031041 · Cited by 249
“Power cycling testing of power modules is essential to understand the wear out of the power components, when they are in operation, and predict when failures might occur [13], for example, through degradation.”
BackgroundChoi, U.-M., Blaabjerg, F., & Jorgensen, S. (2018) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2017.2690500 · Cited by 248
“Typically, in the PC test, high Tj (40 °C∼100 °C) and Tjm (60 °C∼120 °C) are applied to the DUT in order to obtain test results in a reasonable test time [16], [31].”
MethodA Review on IGBT Module Failure Modes and Lifetime Testing
Abuelnaga, A., Narimani, M., & Bahman, A. S. (2021) · IEEE Access · doi:10.1109/access.2021.3049738 · Cited by 246
“important for the verification of models generated from DC platforms [21], [28], [90], [91].”
BackgroundReview and analysis of SiC MOSFETs’ ruggedness and reliability
Wang, J., & Jiang, X. (2020) · IET Power Electronics · doi:10.1049/iet-pel.2019.0587 · Cited by 221
Power Electronics Reliability: State of the Art and Outlook
Wang, H., & Blaabjerg, F. (2021) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2020.3037161 · Cited by 218
“Nevertheless, it is reported that 86% of the power cycling tests have only one sample per test run based on the 70 publications discussed in [4].”
BackgroundMethodInfluentialOnline Junction Temperature Estimation of SiC Power mosfets Through On-State Voltage Mapping
Stella, F., Pellegrino, G., Armando, E. G., & Dapra, D. (2018) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2018.2812710 · Cited by 156
“Thermal cycling magnitude strongly influences semiconductors’ lifetime [14] and [15].”
BackgroundSingle-Pulse Avalanche Mode Robustness of Commercial 1200 V/80 mΩ SiC MOSFETs
Kelley, M. D., Pushpakaran, B. N., & Bayne, S. B. (2017) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2016.2621099 · Cited by 108
“One of the momentous breakthroughs in SiC technology is the development of the high-voltage MOSFET; as SiC fabrication continues to evolve, increased power density and reduced switching and conduction losses can be realized by the replacement of Si devices with SiC devices [9]–[12].”
BackgroundHosseinabadi, F., Chakraborty, S., Bhoi, S. K., Prochart, G., Hrvanovic, D., & Hegazy, O. (2024) · IEEE Open Journal of Power Electronics · doi:10.1109/ojpel.2024.3379294 · Cited by 139
“Additionally, a survey on failure analysis studies conducted between 1993 and 2014, covering 70 publications [49], indicates that die attachment is the primary concern in 30% of cases, followed by wire bonds at 28%.”
BackgroundA Review of Megahertz Current Sensors for Megahertz Power Converters
Xin, Z., Li, H., Liu, Q., & Loh, P. C. (2021) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2021.3136871 · Cited by 95
Wang, L., Zhang, T., Yang, F., Ma, D., Zhao, C., Pei, Y., & Gan, Y. (2022) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2022.3141373 · Cited by 86
“What is more, expanded operating temperature increases the thermal-mechanical stress, which is likely to cause bond wires’ lift-off and fracture [8]–[11].”
BackgroundLi, L.-L., Sun, J. W., Tseng, M., & Li, Z. (2019) · Expert Systems with Applications · doi:10.1016/j.eswa.2019.03.002 · Cited by 84
Role of Threshold Voltage Shift in Highly Accelerated Power Cycling Tests for SiC MOSFET Modules
Luo, H., Iannuzzo, F., & Turnaturi, M. (2020) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2019.2894717 · Cited by 82
“Nowadays, the temperature-dependent reliability issues for power modules have attracted extensive attention from industries and academics [11]–[14].”
BackgroundSugiura, K., Iwashige, T., Tsuruta, K., Chen, C., Nagao, S., Funaki, T., & Suganuma, K. (2019) · IEEE Transactions on Components Packaging and Manufacturing Technology · doi:10.1109/tcpmt.2019.2901543 · Cited by 85
“Typical power cycle tests envision actual operation conditions and environments of the device [26], [27].”
BackgroundThermally Compensated Discontinuous Modulation Strategy for Cascaded H-Bridge Converters
Ko, Y., Andresen, M., Buticchi, G., & Liserre, M. (2017) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2017.2694455 · Cited by 82
“Therefore, the reduction of thermal cycling can extend the lifetime of the converter [13].”
BackgroundDC-DC Boost Converters Parameters Estimation Based on Digital Twin
Nezio, G. D., Benedetto, M. D., Lidozzi, A., & Solero, L. (2023) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2023.3286832 · Cited by 78
Ma, K., Choi, U., & Blaabjerg, F. (2018) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2018.2798585 · Cited by 76
Review of Topside Interconnections for Wide Bandgap Power Semiconductor Packaging
Wang, L., Wang, W., Hueting, R. J. E., Rietveld, G., & Ferreira, J. A. (2023) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2022.3200469 · Cited by 73
“In order to compare the power cycling capability of power modules, the Swiss LESIT (Leistungselektronik Systemtechnik Informationstechnologie) project is the main reference [95], [96].”
BackgroundStudy of Current Density Influence on Bond Wire Degradation Rate in SiC MOSFET Modules
Luo, H., Iannuzzo, F., Baker, N., Blaabjerg, F., Li, W., & He, X. (2020) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2019.2920715 · Cited by 69
“power modules and discrete devices [8]–[11].”
BackgroundPower electronic converter reliability and prognosis review focusing on power switch module failures
Abuelnaga, A. H., Narimani, M., & Bahman, A. S. (2021) · Journal of Power Electronics · doi:10.1007/s43236-021-00228-6 · Cited by 77
Choi, U., Blaabjerg, F., Jørgensen, F. S., Iannuzzo, F., Wang, H., Uhrenfeldt, C., & Munk‐Nielsen, S. (2016) · Microelectronics Reliability · doi:10.1016/j.microrel.2016.07.020 · Cited by 61
Luo, H., Iannuzzo, F., Blaabjerg, F., Turnaturi, M., & Mattiuzzo, E. (2017) · 2017 IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce.2017.8096478 · Cited by 55
“With the aid of power cycling test; the useful life of power module can be achieved rapidly within little time [6], [7].”
BackgroundExperimental Investigation of Linear Cumulative Damage Theory With Power Cycling Test
Zeng, G., Herold, C., Methfessel, T., Schafer, M., Schilling, O., & Lutz, J. (2018) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2018.2859479 · Cited by 54
“publication results, more than 60% of the power cycling tests of power modules from 1994 until now were performed on IGBTs [18].”
BackgroundInfluentialQin, F., Bie, X., An, T., Dai, J., Dai, Y., & Chen, P. (2020) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2020.2992311 · Cited by 54
“For standard wire-bonded IGBT modules, the reliability testing is usually done through the power cycling (PC) tests [5].”
BackgroundMethodInfluentialFailure analysis and lifetime assessment of IGBT power modules at low temperature stress cycles
Hernes, M., D’Arco, S., Antonopoulos, A., & Peftitsis, D. (2021) · IET Power Electronics · doi:10.1049/pel2.12083 · Cited by 49
“Hence, the accelerated PCT is the approach generally adopted for assessing long-term reliability of high-power IGBT modules, as well as, for modelling their expected lifetime [3, 4].”
BackgroundMethodRecent advances and trend of HEV/EV‐oriented power semiconductors – an overview
Liu, G., Li, K., Wang, Y., Luo, H., & Luo, H. (2019) · IET Power Electronics · doi:10.1049/iet-pel.2019.0401 · Cited by 44
Thermal Stresses Relief Carrier-Based PWM Strategy for Single-Phase Multilevel Inverters
Aly, M., Ahmed, E. M., & Shoyama, M. (2017) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2017.2654490 · Cited by 43
“Various models of power semiconductor device: (a) Relationship between models, and (b) Nf versus Tj and ΔTj [20].”
MethodThermal stress reduction strategy for high-temperature power electronics with Ag sintering
Ren, H., Zou, G., Jia, Q., Deng, Z., Du, C., Wang, W., & Liu, L. (2021) · Microelectronics Reliability · doi:10.1016/j.microrel.2021.114379 · Cited by 42
Guo, W., Ma, M., Wang, H., Xiang, N., Wang, H., Chen, Z., & Chen, W. (2022) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2022.3176284 · Cited by 43
“As indicated from the industry survey, the degradation and lifetime are mainly affected by temperature factor [5].”
BackgroundReview of SiC MOSFET based three-phase inverter lifetime prediction
Ni, Z., Lyu, X., Yadav, O. P., & Cao, D. (2017) · 2017 IEEE Applied Power Electronics Conference and Exposition (APEC) · doi:10.1109/apec.2017.7930819 · Cited by 40
“Drain-source on-state voltage Vds_on [34]-[37] Stress level much higher than wire bond’s strain level High junction temperature increase of Vds_on Vds_on increases by 5% ~ 20% [34] Wire bond lift-off/ Wire bond”
BackgroundReview of State-of-the-Art Integration Technologies in Power Electronic Systems
Wang, K. (2017) · CPSS Transactions on Power Electronics and Applications · doi:10.24295/cpsstpea.2017.00027 · Cited by 47
Modeling of Short-Circuit-Related Thermal Stress in Aged IGBT Modules
Bahman, A. S., Iannuzzo, F., Uhrenfeldt, C., Blaabjerg, F., & Munk‐Nielsen, S. (2017) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2017.2702594 · Cited by 40
“, wind turbines, ships, and trains [1]–[3].”
Wang, M., Chen, Y., He, Z., Wu, Z., & Li, B. (2023) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2023.3257885 · Cited by 38
“Typical aging precursors in PCT for SiC power MOSFETs are gate leakage current (Igss) [5], [13], drain leakage current (Idss) [7], threshold voltage (Vgs(th)) [14], [15], ON-state resistance (RDS(on)) [16], body diode voltage (Vsd) [17], and thermal resistance (Rth(jc)) [18].”
BackgroundAnalysis of electrical tree inception in silicone gels
Mancinelli, P., Cavallini, A., Dodd, S. J., Chalashkanov, N. M., & Dissado, L. A. (2017) · IEEE Transactions on Dielectrics and Electrical Insulation · doi:10.1109/tdei.2017.006865 · Cited by 35
Zhao, J., An, T., Fang, C., Bie, X., Qin, F., Chen, P., & Dai, Y. (2019) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2019.2895695 · Cited by 40
“POWER electronics devices such as insulated gate bipolar transistors (IGBTs) use semiconductor technology to control and convert electrical power, and these devices are widely used in electrical traction applications, such as cars, subways, elevators, and locomotives [1].”
BackgroundThermal Cycling of Sintered Silver (Ag) Joint as Die-Attach Material
Siow, K. S., & Chua, S. T. (2019) · JOM · doi:10.1007/s11837-019-03461-4 · Cited by 35
Choe, C., Chen, C., Nagao, S., & Suganuma, K. (2020) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2020.3024986 · Cited by 38
“The temperature swing was repeated up to failure based on the failure criteria, which was defined as an increase in the VF by 20% when compared to its initial value to protect the tested discrete devices against catastrophic failure [32].”
MethodReview of Active Front-End Rectifiers in EV DC Charging Applications
Zhaksylyk, A., Rasool, H., Abramushkina, E. E., Chakraborty, S., Geury, T., Baghdadi, M. E., & Hegazy, O. (2023) · Batteries · doi:10.3390/batteries9030150 · Cited by 43
Die degradation effect on aging rate in accelerated cycling tests of SiC power MOSFET modules
Luo, H., Baker, N., Iannuzzo, F., & Blaabjerg, F. (2017) · Microelectronics Reliability · doi:10.1016/j.microrel.2017.07.004 · Cited by 35
Effect of Ag Sintered Bondline Thickness on High-Temperature Reliability of SiC Power Devices
Deng, Z., Zou, G., Jia, Q., Feng, B., Zhang, H., Ren, H., & Liu, L. (2021) · IEEE Transactions on Components Packaging and Manufacturing Technology · doi:10.1109/tcpmt.2021.3110997 · Cited by 30
Review on Power Cycling Reliability of SiC Power Device
Gao, X., Jia, Q., Wang, Y., Zhang, H., Ma, L., Zou, G., & Guo, F. (2024) · Electronic Materials · doi:10.3390/electronicmat5020007 · Cited by 36
“Mismatch in the coefficients of thermal expansion (CTE) between the structural layers’ characteristics, such as “stack”, can trigger device failures [13].”
BackgroundCalabretta, M., Sitta, A., Oliveri, S. M., & Sequenzia, G. (2021) · IEEE Access · doi:10.1109/access.2021.3080505 · Cited by 31
“The main limiting factors for power module durability are represented by lift-off wire bonding degradation and die attach solder delamination [6].”
BackgroundChen, C., Kim, D., Liu, Y., Sekiguchi, T., Su, Y., Long, X., Liu, C., Liu, C., & Suganuma, K. (2023) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2023.05.104 · Cited by 28
Zhang, Y., Heimler, P., Abuogo, J. O., Zhang, X., Zhang, Y., Xie, D., Zhang, Y., Zhang, K., Li, X., Luo, H., et al. (2025) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2025.3595180 · Cited by 46
“A comprehensive review by Durand et al. [6] revealed that test outcomes are affected by a wide array of factors, including the four control strategies above, at least four junction temperature measurement methods, and over ten different failure criteria.”
InfluentialTran, S.-H., Khatir, Z., Lallemand, R., Ibrahim, A., Ousten, J.-P., Ewanchuk, J., & Mollov, S. V. (2019) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2018.2847234 · Cited by 26
“The constant ΔTj method has been implemented by varying the tON/tOFF parameters [13]–[15] but very few papers report a gate voltage regulation implementation [16], [17].”
BackgroundMethodThermal Stress Analysis Comparison in IGBT Power Modules between DC and Switching Power Cycling
Khatir, Z., Lallemand, R., Ibrahim, A., & Ingrosso, D. (2023) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2023.3289890 · Cited by 28
“The test principle is based on thermal fatigue of the devices due to periodic succession of self-heating and cooling phases [6], [7], [8].”
BackgroundPower cycling failure analysis of double side cooled IGBT modules for automotive applications
Ma, Y., Li, J., Dong, F., & Yu, J. (2021) · Microelectronics Reliability · doi:10.1016/j.microrel.2021.114282 · Cited by 25
Using Laminated Metal Foam as the Top-Side Contact of a PCB-Embedded Power Die
Pascal, Y., Abdedaim, A., Labrousse, D., Petit, M., Lefebvre, S., & Costa, F. (2017) · IEEE Electron Device Letters · doi:10.1109/led.2017.2748223 · Cited by 25
“Second, the relatively low reliability of bonding wires often determines package lifetime [2], [3].”
BackgroundLuo, H., Reigosa, P. D., Iannuzzo, F., & Blaabjerg, F. (2018) · Microelectronics Reliability · doi:10.1016/j.microrel.2018.07.128 · Cited by 26
Jørgensen, A. B., Munk‐Nielsen, S., & Uhrenfeldt, C. (2021) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2021.3054336 · Cited by 24
“Conventional power module structures have several decades of knowledge to rely on, including: failure-mode analysis, lifetime testing, and millions of hours of field operation [12]–[17].”
BackgroundModulation Strategies for Thermal Stress Control of CHB Inverters
Ko, Y., Kuprat, J., Pugliese, S., & Liserre, M. (2021) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2021.3117917 · Cited by 26
Digital Twin based Real-Time Analysis of DC-DC Boost Converters
Nezio, G. D., Benedetto, M. D., Lidozzi, A., & Solero, L. (2022) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce50734.2022.9947394 · Cited by 27
Power Semiconductor Devices and Packages: Solder Mechanical Characterization and Lifetime Prediction
Calabretta, M., Sitta, A., Oliveri, S. M., & Sequenzia, G. (2021) · IEEE Access · doi:10.1109/access.2021.3056281 · Cited by 23
“An unified material model is indeed suggested, resulting a valid and common approach for solder mechanical modeling [6].”
Online Optimal Switching Frequency Selection for Grid-Connected Voltage Source Inverters
Albatran, S., Smadi, I. A., Ahmad, H. J., & Koran, A. (2017) · Electronics · doi:10.3390/electronics6040110 · Cited by 24
Reliability Assessment of Multistate Degraded Systems: An Application to Power Electronic Systems
Samavatian, V., Iman‐Eini, H., & Avenas, Y. (2019) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2019.2933063 · Cited by 23
Study of IGBTs Reliability Under Coupled Electrical–Thermal Environment
Meng, H., Wang, Y., Zheng, X., Chen, J., Wu, Y., Li, A., & Huang, Y. (2020) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2020.2988847 · Cited by 26
Zhang, Q., & Zhang, P. (2023) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2023.3270530 · Cited by 23
High Cycle Fatigue Testing of Silicon IGBT Devices Under Application-Close Conditions
Schwabe, C., Thönelt, N., Lutz, J., & Basler, T. (2023) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2023.3296269 · Cited by 22
Impact of Accelerated Stress-Tests on SiC MOSFET Precursor Parameters
Kozak, J. P., Ngo, K. D. T., DeVoto, D. J., & Major, J. J. (2018) · International Symposium on 3D Power Electronics Integration and Manufacturing (3D-PEIM) · doi:10.1109/3dpeim.2018.8525234 · Cited by 27
“The experimental rate of the heating and cooling periods can be designed to match different industry applications [11], [12] through current magnitude, and cooling systems.”
BackgroundInfluentialPower Cycling Capability Comparison of Si and SiC MOSFETs under Different Conduction Modes
Chen, J., Deng, E., Zhao, Z., Wu, Y., & Huang, Y. (2020) · IEEE International Symposium on Power Semiconductor Devices and ICs/Proceedings of the International Symposium on Power Semiconductor Devices & ICs/Proceedings of the ... International Symposium on Power Semiconductor Devices & ICs/Proceedings of the ... International Symposium on Power Semiconductor Devices and ICs · doi:10.1109/ispsd46842.2020.9170163 · Cited by 23
“Power cycling test (PCT) is the most important reliability test to evaluate the reliability of power electronics, normally with DC injection in conduction mode [1].”
BackgroundA Junction Temperature Online Monitoring Method for IGBTs Based on Turn-off Delay Time
Tang, T., Song, W., Yang, K., & Chen, J. (2023) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2023.3284417 · Cited by 21
Morak, M., Marx, P., Gschwandl, M., Fuchs, P., Pfost, M., & Wiesbrock, F. (2018) · Polymers · doi:10.3390/polym10101131 · Cited by 22
“The thermal loading cycle with the abovementioned parameters was chosen in alignment to the power thermal cycle (PTC) test, which is one type of conventional test method in the field of microelectronics [22,24].”
BackgroundMethodThree-phase SiC inverter with active limitation of all MOSFETs junction temperature
Stella, F., Pellegrino, G., & Armando, E. G. (2020) · Microelectronics Reliability · doi:10.1016/j.microrel.2020.113659 · Cited by 23
Zhang, Z., Chen, C., Suetake, A., Ishino, H., Sampei, H., Endo, T., Sugiura, K., Tsuruta, K., & Suganuma, K. (2022) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2022.3209740 · Cited by 22
“The high junction temperature can cause severe thermomechanical stresses that will lead to failures like solder fatigue, bonding wire liftoff, and substrate deformation [6].”
BackgroundNwanoro, K. C., Lu, H., Yin, C., & Bailey, C. (2022) · Power Electronic Devices and Components · doi:10.1016/j.pedc.2022.100027 · Cited by 21
Coordinated On-line Junction Temperature Estimation and Prognostic of SiC Power Modules
Stella, F., Pellegrino, G., & Armando, E. G. (2018) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce.2018.8557850 · Cited by 21
“Among many possible techniques, thermal cycling was selected, as it is recognized as one of the most effective regarding package related failure progress [14].”
BackgroundRen, H., Zou, G., Zhao, Z., Wan, M., Zhang, H., Jia, Q., & Liu, L. (2020) · IEEE Transactions on Components Packaging and Manufacturing Technology · doi:10.1109/tcpmt.2020.3038430 · Cited by 22
“It is well known that the reliability under longtime power cycling of power modules mainly suffers from fatigue and thermal stress, which lead to the formation of cracks [3].”
BackgroundAdvanced power cycler with intelligent monitoring strategy of IGBT module under test
Choi, U., Blaabjerg, F., & Iannuzzo, F. (2017) · Microelectronics Reliability · doi:10.1016/j.microrel.2017.06.029 · Cited by 21
Barón, K. M., Sharma, K., Nitzsche, M., & Kallfass, I. (2021) · Conference proceedings/Conference proceedings - IEEE Applied Power Electronics Conference and Exposition · doi:10.1109/apec42165.2021.9487142 · Cited by 21
Rajaguru, P., Lu, H., Bailey, C., & Bella, M. (2020) · Microelectronics Reliability · doi:10.1016/j.microrel.2020.113697 · Cited by 18
Xiao, X., Ge, X., Ke, Q., Yong, L., Liao, Y., Wang, H., & Zhang, Y. (2022) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2022.3231718 · Cited by 21
“Thus, the overall thermal impedance of the IGBT module is described by a first-order thermal model, and the characteristic functions can be rewritten as fun1 = T (n)high T (n)low = e 12Rth,all Cth,all f (27) fun2 = T (n)high + T (n)low = P Rth,all (28) where Rth,all and Cth,all are the overall resistance and capacitan…”
BackgroundInfluentialThermal measurement and numerical analysis for automotive power modules
Sitta, A., Renna, M., Messina, A. A., Sequenzia, G., D'Arrigo, G. A., & Calabretta, M. (2020) · International Conference on Thermal, Mechanical and Multi-Physics Simulation and Experiments in Microelectronics and Microsystems (EuroSimE) · doi:10.1109/eurosime48426.2020.9152204 · Cited by 18
“The most frequent bottlenecks are mainly represented by die attach degradation and wire bonding lift-off [8], [9].”
BackgroundReview on the Thermal Models Applications in the Reliability of Power Semiconductor Device
Zhang, J., Shen, H., Sun, H., & Wang, Z. (2025) · IET Power Electronics · doi:10.1049/pel2.70065 · Cited by 21
Kim, D., Noh, S., Park, S. M., & Kim, M. (2023) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2023.107603 · Cited by 16
Ren, H., Zhao, S., Jian, M., Wang, W., Han, Z., Li, Z., Li, Q., Wang, J., & Liu, Y. (2024) · IEEE Transactions on Electron Devices · doi:10.1109/ted.2024.3404417 · Cited by 19
“The mismatch of coefficients of thermal expansion (CTE) between different materials in the package eventually leads to module failure, the most common of which is bond wire failure and solder layer fatigue failure [2], [3].”
BackgroundRoshanghias, A., Malagò, P., Kaczynski, J., Polom, T. A., Bardong, J., Holzmann, D., Malik, M., Ortner, M., Hirschl, C., & Binder, A. (2021) · Energies · doi:10.3390/en14082176 · Cited by 15
Pino, C., Sitta, A., Castagnolo, G., Messina, A. A., Coffa, S., Calabretta, M., Scotti, F., Genovese, A., Piuri, V., Spampinato, C., et al. (2023) · IEEE Transactions on Intelligent Vehicles · doi:10.1109/tiv.2023.3294726 · Cited by 17
“Operative conditions, like device temperature swing during active cycle, can trigger interface degradation like wire bonding lift-off, which impact directly device on-state drain-source resistance [6].”
BackgroundChoi, U., Jørgensen, F. S., Iannuzzo, F., & Blaabjerg, F. (2018) · Microelectronics Reliability · doi:10.1016/j.microrel.2018.07.002 · Cited by 15
Experimentally validated methodology for real-time temperature cycle tracking in SiC power modules
Stella, F., Olanrewaju, O., Yang, Z., Castellazzi, A., & Pellegrino, G. (2018) · Microelectronics Reliability · doi:10.1016/j.microrel.2018.07.072 · Cited by 15
Challenges of SiC MOSFET Power Cycling Methodology
Gothner, F., Spro, O. C., Herncs, M., & Peftitsis, D. (2018) · NORA - Norwegian Open Research Archives · Cited by 18
Whitt, R., Yuan, Z., Emon, A. I., Luo, F., & Huitink, D. R. (2022) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2022.3200402 · Cited by 16
“From a physics of failure perspective, the underlying mechanism driving device malfunction is thermal cycling [3].”
BackgroundYang, X., Wu, X., Heng, K., & Liu, G. (2023) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2023.3244368 · Cited by 15
“In experiments, the strategy of constant timing switches the load current on and off in fixed time intervals [33].”
BackgroundSong, S., Munk‐Nielsen, S., & Uhrenfeldt, C. (2019) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2019.2956125 · Cited by 15
“[36], and the stress is intimately linked with temperature [20],”
BackgroundSingle-pulse avalanche mode operation of 10-kV/10-A SiC MOSFET
Kelley, M. D., Pushpakaran, B. N., Bilbao, A. V., Schrock, J. A., & Bayne, S. B. (2018) · Microelectronics Reliability · doi:10.1016/j.microrel.2017.12.011 · Cited by 13
Reliability Criteria for Thick Bonding Wire
Dagdelen, T., Abdel-Rahman, E. M., & Yavuz, M. (2018) · Materials · doi:10.3390/ma11040618 · Cited by 14
Samavatian, V., Iman‐Eini, H., Avenas, Y., & Shemehsavar, S. (2019) · IEEE Transactions on Components Packaging and Manufacturing Technology · doi:10.1109/tcpmt.2019.2940058 · Cited by 12
“The degradation has been indicated by increases in the ON-state voltage and the junctionto-case thermal resistance [8], [9].”
BackgroundComparative evaluation of reliability assessment methods of power modules in motor drive inverter
Choi, U., Vernica, I., Zhou, D., & Blaabjerg, F. (2020) · Microelectronics Reliability · doi:10.1016/j.microrel.2020.113730 · Cited by 12
Samavatian, V., Iman‐Eini, H., Avenas, Y., & Samavatian, M. (2022) · Journal of Electronic Materials · doi:10.1007/s11664-022-09777-3 · Cited by 12
Ye, J., Yang, X., Dai, X., Wu, X., Heng, K., & Liu, G. (2023) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2023.3337111 · Cited by 12
“For standard Al wires bonded IGBT modules, the reliability studies of bond wires are usually conducted through power cycling (PC) tests and finite element model (FEM) simulations [8].”
MethodWarpage Behavior on Silicon Semiconductor Device: The Impact of Thick Copper Metallization
Calabretta, M., Sitta, A., Oliveri, S. M., & Sequenzia, G. (2021) · Applied Sciences · doi:10.3390/app11115140 · Cited by 11
Chen, J., Liu, Y., Yang, J., He, L. M., Tang, H., & Li, X. (2025) · Soldering and Surface Mount Technology · doi:10.1108/ssmt-05-2025-0032 · Cited by 15
A survey on LED Prognostics and Health Management and uncertainty reduction
Rocchetta, R., Perrone, E., Herzog, A., Dersin, P., & Bucchianico, A. D. (2024) · Microelectronics Reliability · doi:10.1016/j.microrel.2024.115399 · Cited by 11
Kalay, M. Ş., & Akpolat, A. N. (2025) · IET Renewable Power Generation · doi:10.1049/rpg2.70111 · Cited by 19
A New Package for SiC Power Modules with Ceramic Heatsink
Zhang, Z., Yuan, X., & Xie, L. (2022) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce50734.2022.9947714 · Cited by 11
“This construction is widely used in the production of power modules [4].”
BackgroundMultiparameter reliability model for SiC power MOSFET subjected to repetitive thermomechanical load
Bąba, S. (2021) · Bulletin of the Polish Academy of Sciences Technical Sciences · doi:10.24425/bpasts.2021.137386 · Cited by 11
“Thus, there is a significant difference between PC and CC test results [24].”
BackgroundAnalysis of PCB embedded power semiconductors for a 30 kW boost PFC converter
Wyss, J., & Biela, J. (2016) · European Conference on Power Electronics and Applications · doi:10.1109/epe.2016.7695519 · Cited by 14
“Different approaches to improve the reliability have been investigated [1], as for example the SKiN technology [2], a development for modules where the bond wires are replaced by a sinter joint, thereby improving the reliability considerably or the .”
MethodChoi, U., Lee, J. S., & Blaabjerg, F. (2019) · Microelectronics Reliability · doi:10.1016/j.microrel.2019.113460 · Cited by 10
Peng, Y., Wang, H., & Wang, H. (2023) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2023.3273269 · Cited by 12
“…reliability as the silicon-based power device chip has stable characteristics due to mature chip manufacturing technology compared to the package [1], [2], and many researches have been performed to achieve the following two targets: 1) predictive maintenance based on the monitored wear-out…”
MethodGómez, P. I., Gajardo, M. E. L., Mijatović, N., & Dragičević, T. (2024) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2023.3347839 · Cited by 13
Metadata
- Authors
- Durand, C., Klingler, M., Coutellier, D., & Naceur, H.
- Affiliations
- Laboratoire d'Automatique, de Mécanique et d'Informatique Industrielles et Humaines (FR)
- Robert Bosch (Germany) (DE)
- Centre National de la Recherche Scientifique (FR)
- Venue
- IEEE Transactions on Device and Materials Reliability
- Published
- 2016-03
- Volume
- 16
- Issue
- 1
- Pages
- 80-97
- ISSN
- 1530-4388 (ISSN-L)
- 1558-2574
- OpenAlex
- W2294980933
- Cited by
- 239
- References
- 94
- Citations by year
- 2026: 26 · 2025: 29 · 2024: 24 · 2023: 29 · 2022: 26 · 2021: 29 · 2020: 19 · 2019: 25 · 2018: 17 · 2017: 12 · 2016: 3
- FWCI
- 8.76
- Type
- journal article
- Language
- en
- Open access
- green
- uphf.hal.science
- Locations
- IEEE Transactions on Device and Materials Reliability (publishedVersion)
- HAL (submittedVersion, other-oa)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Silicon Carbide Semiconductor Technologies
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Electronic Packaging and Soldering Technologies
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Semiconductor materials and devices
- Keywords
- power cycling reliability, power modules, power devices, traction applications, IGBT, metal-oxide-semiconductor field-effect transistors, power cycling test, fatigue process, heat sinks
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.