Biodegradable synthetic polymers for tissue engineering
Open accessThe DOI matches its Crossref record; 96 of the 97 references it cites were found in a registry or an index; 1 of the 146 sources its claims cite were checked for support.
Abstract
This review focuses on biodegradable synthetic polymers, discussing synthesis, properties and biodegradability, especially within the polyester family including polylactides.
Overview
CoChat Summary
TL;DR
This review surveys biodegradable synthetic polymers for tissue engineering, emphasizing polyesters (PGA, PLA, PLGA), polylactones, poly(propylene fumarate), polyanhydrides, tyrosine-derived polycarbonates, polyorthoesters, polyurethanes, and polyphosphazenes. It concludes that polyesters dominate clinically, while injectable in situ curable systems such as PPF and photocrosslinkable polyanhydrides are promising but face challenges in biocompatibility, degradation control, and heat generation.
Key findings
- Polyesters are the most studied biodegradable polymers. PGA has 46–50% crystallinity, Tg 36°C, Tm 225°C; in Dexon sutures in vitro, first-stage degradation predominates for 21 days, crystalline degradation takes a further 28 days, and after 49 days weight loss was about 42% with complete loss of mechanical properties.
- PLA/PGA copolymer behavior depends on composition: 25–75% (l)LA/GA and 0–70% (dl)LA/GA are amorphous; 70/30 GA/LA has the highest water uptake, while 50/50 is reported as most unstable to hydrolysis; Vicryl is 8% (l)LA and 92% GA.
- Poly(caprolactone) degrades slowly: homopolymer degradation is on the order of 2–3 years, and PCL with initial average molecular weight 50,000 takes about 3 years for complete in vitro degradation.
- Poly(propylene fumarate) degrades to fumaric acid and propylene glycol; time to 20% original weight loss ranged from 84 days (PPF/β-TCP composite) to over 200 days (PPF/CaSO4 composite). PPF formulations showed maximum curing temperatures of 38–48°C versus 94°C for PMMA cements, curing times of 1–121 min, and compressive strengths of 1–12 MPa.
- Polyanhydrides degrade by surface erosion; poly(sebacic acid) degrades in about 54 days in saline, while poly(1,6-bis(p-carboxyphenoxy)hexane) is estimated at 1 year. Poly[1,6-bis(carboxyphenoxy)hexane] has a Young’s modulus of 1.3 MPa versus human bone at 40–60 MPa; poly(anhydride-co-imides) reached compressive strengths of 50–60 MPa, and photocrosslinked systems showed compressive strengths of 30–40 MPa and tensile strengths of 15–27 MPa.
- Degradable polyurethanes based on lysine diisocyanate showed varied properties: dl-lactide networks were rigid (Tg = 60°C) with ultimate tensile strengths of ~40–70 MPa, caprolactone triol networks were low-modulus elastomers with tensile strengths of 1–4 MPa, and copolymer networks had elongation up to 600% with compressive strengths of 3–25 MPa. In vivo, porous polyurethane artificial skin degraded almost completely 4–8 weeks after implantation in guinea pigs with no adverse tissue reaction.
Methods
- Design: narrative literature review; no primary experimental study or systematic review protocol is reported.
- Data/sample: published literature on biodegradable synthetic polymers, including synthesis, properties, degradation, biocompatibility, and injectable polymer systems; Tables 1–3 summarize polymer properties and precursors.
- Analysis: qualitative synthesis of major polymer classes, their degradation modes/products, mechanical properties, biocompatibility, and potential for injectable tissue-engineering compositions.
Limitations
- Stated: the paper notes that Table 2 data “should be used as a guide only” and that sufficient data are not available to provide a comprehensive list of properties for polyanhydrides, polycarbonates, polyurethanes, and polyphosphazenes.
- Stated: for polyanhydrides, no data are reported about polymer sterilizability and heat generation during polymerization; for degradable polyurethanes, the effect of degradation products and how they are removed from the body are not clearly understood.
- Evident: as a narrative review, it lacks systematic search criteria, study quality appraisal, and meta-analysis, so conclusions depend on the cited literature and may not comprehensively cover all biodegradable polymers or tissue-engineering applications.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
1 Valid · 20 Not valid · 105 Not checked · 89 Own results and interpretations
Every source the paper cites for this claim was checked and supports it.
In the paper
“A meniscal replica implanted contained only fibro-cartilage after 18 weeks and decreased the degradation of the articular cartilage.”
What the sources say
- Supportedcites De Groot et al.., 1996 source
The Aliphatic PU network passage (page not provided) reports that articular-cartilage degeneration was less severe with the prosthesis than in meniscectomized control knees. It also says the prostheses contained only fibrocartilage after 18 weeks. Degeneration was reduced, not eliminated. (LLM, conf=0.91)
plainstates a causeSingle case- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
In the paper
“The compressive strengths varied between 1 and 12 MPa”
What the sources say
- Not matchedcites Peter et al., 1998a
Couldn’t be matched to a paper in Crossref, so it can’t be checked.
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Not matched
In the paper
“Cross-linking characteristics reported for PPF, N-vinyl pyrrolidone (N-VP), benzoyl peroxide, sodium chloride, and TCP indicate that for a range of formulations, the maximum temperature varied within 38 to about 48ºC, compared to 94ºC observed for polymethylmethacrylate (PMMA) cements.”
What the sources say
- Not matchedcites Peter et al., 1998a
Couldn’t be matched to a paper in Crossref, so it can’t be checked.
hedged- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Not matched
None of the sources cited for this claim could be matched to a paper in Crossref, so there is nothing to check it against.
In the paper
“Based on in-vitro studies, the time required to reach 20% loss in original weight ranged from 84 (PPF/ß-TCP composite) to over 200 days (PPF/CaSO 4 composite)”
What the sources say
- Not matchedcites Peter et al., 1997b
Couldn’t be matched to a paper in Crossref, so it can’t be checked.
- Not matchedcites Kharas et al., 1997
Couldn’t be matched to a paper in Crossref, so it can’t be checked.
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Not matched
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“These composite materials exhibit compressive strengths in the range 2 to 30 MPa.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
94 more claims
Create a free account to see all 215 claims and to verify the 2 references still open.
- It may state two separate claims as one. 62
- Probably not a substantial claim. 76
- The quote only partly states this claim. 1
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“Advantages include a tightly controlled manufacturing process, accurate reproducibility, adjustable biodegradability, and a wide variety of both chemical and physical properties.[ 171 ]”
From Unraveling and Harnessing the Immune Response at the Cell–Biomaterial Interface for Tissue Engineering Purposes (2024) · cites this paper as [171]
Experimental — accuracy not yet measured
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
§ Polyanhydrides
“Polyanhydrides degrades by surface erosion (Kohn and Langer, 1997) and their main applications are in controlled drug delivery.”
§ Conclusions
“Polyanhydride degrade by bulk erosion and their main applications are in controlled drug delivery.”
Citations
Cites
Synthetic biodegradable polymers as orthopedic devices
Middleton, J. C., & Tipton, A. J. (2000) · Biomaterials · doi:10.1016/s0142-9612(00)00101-0 · Cited by 2,741 · cited 4×
“…developments in siloxane-based polyurethanes, which have greater in-vivo stability than conventional polyetherurethanes (e.g., poly(tetramethylene oxide) (PTMO)-based) have provided opportunities for development of a range of medical implants for chronic applications (Gunatillake et al., 2001).”
BackgroundInfluentialBiomaterial developments for bone tissue engineering
Burg, K. J. L., Porter, S., & Kellam, J. F. (2000) · Biomaterials · doi:10.1016/s0142-9612(00)00102-2 · Cited by 1,643 · cited 1×
“Polyesters have also been considered for development of tissue engineering applications (Hubbell, 1995; Thomson et al 1995a, Yazemski et al. 1996; Wong and Mooney, 1997), particularly for bone tissue engineering (Kohn and Langer, 1997; Burg et al., 2000).”
BackgroundChandra, R. (1998) · Progress in Polymer Science · doi:10.1016/s0079-6700(97)00039-7 · Cited by 1,462
Biodegradable polymers for use in surgery—polyglycolic/poly(actic acid) homo- and copolymers: 1
Gilding, D. K., & Reed, A. M. (1979) · Polymer · doi:10.1016/0032-3861(79)90009-0 · Cited by 1,345
Biomaterials in Tissue Engineering
Hubbell, J. A. (1995) · Nature Biotechnology · doi:10.1038/nbt0695-565 · Cited by 1,060 · cited 1×
“Polyesters have also been considered for development of tissue engineering applications (Hubbell, 1995; Thomson et al 1995a, Yazemski et al. 1996; Wong and Mooney, 1997), particularly for bone tissue engineering (Kohn and Langer, 1997; Burg et al., 2000).”
BackgroundPolylactic Acid for Surgical Implants
KULKARNI, R. K. (1966) · Archives of Surgery · doi:10.1001/archsurg.1966.01330050143023 · Cited by 841
Evolution of bone transplantation: molecular, cellular and tissue strategies to engineer human bone
Yaszemski, M. J., Payne, R. G., Hayes, W. C., Langer, R., & Mikos, A. G. (1996) · Biomaterials · doi:10.1016/0142-9612(96)85762-0 · Cited by 729
Miller, R. A., Brady, J. M., & Cutright, D. E. (1977) · Journal of Biomedical Materials Research · doi:10.1002/jbm.820110507 · Cited by 722 · cited 2×
“For the (l)LA/GA copolymers, resistance to hydrolysis is more pronounced at either end of the copolymers compositions range (Miller et al., 1977; Gilding and Reed, 1979; Reed and Gilding, 1981; Vert et al., 1984).”
BackgroundInjectable biodegradable materials for orthopedic tissue engineering
Temenoff, J. S., & Mikos, A. G. (2000) · Biomaterials · doi:10.1016/s0142-9612(00)00108-3 · Cited by 554 · cited 8×
“A number of methods have been reported to prepare PPF, and each results in different polymer properties (Peter et al., 1997a,b, 1999; Temenoff and Mikos 2000).”
BackgroundMethodInfluentialLeong, K. W., Brott, B. C., & Langer, R. (1985) · Journal of Biomedical Materials Research · doi:10.1002/jbm.820190806 · Cited by 541 · cited 12×
“The polyurethanes ranged from elastomers with elongations at break as high as 780 %, but with low tensile strengths (5.8 to 8.1 MPa).”
BackgroundInfluential
Research works printed but not linked: 5
- Scranton A, Bowman C, Peiffer R, eds. ACS Symposium Series 673; American Chemical Society, Washington DC. pp 189-202.
- Ratner BD, Hoffman AS, Schoen FJ, Lemon JE, eds. Aca- demic Press, San Diego. pp 65-73.
- Lamba NMK, Woodhouse KA, Cooper SL (1998) Poly- urethanes in Biomedical Applications. CRC Press: New York p 205-241.
- Mark JE, Alcock HR, West R (1992) Inorganic Poly- mers. Prentice Hall, Upper Saddle River, NJ. Chapter
- Ng SY, Vandamme T, Tayler MS, Heller J (1997) Syn- thesis and erosion studies of self-catalysed poly(orthoester)s. Macromolecules 30: 770-772.
Cited by
Items 401–500 of 1,762
Bhattacharjee, P., Kundu, B., Naskar, D., Kim, H., Bhattacharya, D., Maiti, T. K., & Kundu, S. C. (2015) · Cell and Tissue Research · doi:10.1007/s00441-015-2232-6 · Cited by 55
Sreerekha, P. R., Chennazhi, K. P., Nair, S. V., Menon, D., & Unnithan, A. R. (2011) · Tissue Engineering Part C Methods · doi:10.1089/ten.tec.2010.0734 · Cited by 54
MBG/ PGA-PCL composite scaffolds provide highly tunable degradation and osteogenic features
Li, J., Wang, C., Gao, G., Yin, X., Pu, X., Shi, B., Liu, Y., Huang, Z., Wang, J., Li, J., et al. (2021) · Bioactive Materials · doi:10.1016/j.bioactmat.2021.11.034 · Cited by 57
“widely used to construct bone tissue engineering scaffolds [6,7].”
BackgroundGaladari, H., van Abel, D., Nuami, K. A., Faresi, F. A., & Galadari, I. H. (2015) · Journal of Cosmetic Dermatology · doi:10.1111/jocd.12126 · Cited by 56
Wit, M. A. D., Wang, Z., Atkins, K. M., Mequanint, K., & Gillies, E. R. (2008) · Journal of Polymer Science Part A Polymer Chemistry · doi:10.1002/pola.22915 · Cited by 53
Dehnavi, S. S., Mehdikhani, M., Rafienia, M., & Bonakdar, S. (2018) · Materials Science and Engineering C · doi:10.1016/j.msec.2018.04.065 · Cited by 58
Chakravarty, J., Rabbi, M. F., Chalivendra, V., Ferreira, T., & Brigham, C. J. (2019) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2019.10.168 · Cited by 61
Synthetic polymers as bone engineering scaffold
Javid‐Naderi, M. J., Behravan, J., Karimi‐Hajishohreh, N., & Toosi, S. (2023) · Polymers for Advanced Technologies · doi:10.1002/pat.6046 · Cited by 53
Liu, Y., Xu, L. J., & Liang, A. (2022) · Frontiers in Bioengineering and Biotechnology · doi:10.3389/fbioe.2022.1042128 · Cited by 61
“However, studies have shown that aliphatic polyesters produce acidic degradation products during the degradation process, which can lead to sterile inflammation, bacterial growth at bone lesions, and bone resorption or bone loss (Gunatillake et al., 2003; Böstman et al., 2005; Reich et al., 2020).”
BackgroundDevelopment of Biocompatible 3D-Printed Artificial Blood Vessels through Multidimensional Approaches
Choi, J., Lee, E. J., Jang, W. B., & Kwon, S. (2023) · Journal of Functional Biomaterials · doi:10.3390/jfb14100497 · Cited by 61
“These materials are well-tolerated by the body and gradually degrade over time as natural tissue forms [231,232].”
BackgroundAlavi, S. E., Gholami, M., Shahmabadi, H. E., & Reher, P. (2023) · Journal of Clinical Medicine · doi:10.3390/jcm12226962 · Cited by 61
“It is crucial to remember that terminology in the AM industry is flexible; for instance, the PBF process may also be referred to as direct metal laser sintering, selective laser sintering (SLS), or selective laser melting.”
Davachi, S. M., Kaffashi, B., Zamanian, A., Torabinejad, B., & Ziaei-Rad, Z. (2015) · Materials Science and Engineering C · doi:10.1016/j.msec.2015.08.026 · Cited by 54
Luo, L., Gan, L., Liu, Y., et al. (2015) · Biochemical and Biophysical Research Communications · doi:10.1016/j.bbrc.2014.12.121 · Cited by 52
Tissue Engineering Bionanocomposites Based on Poly(propylene fumarate)
Diez-Pascual, A. M. (2017) · Polymers · doi:10.3390/polym9070260 · Cited by 52
Morgan, S. M., Tilley, S., Perera, S. P., Ellis, M. J., Kanczler, J. M., Chaudhuri, J. B., & Oreffo, R. O. C. (2007) · Biomaterials · doi:10.1016/j.biomaterials.2007.08.029 · Cited by 51
“It is expected that rapid mass loss, which follows pseudo-first-order kinetics, occur after a certain period of time into the degradation [61,62].”
BackgroundA Poly(Lactic Acid-Co-Caprolactone)–Collagen Hybrid for Tissue Engineering Applications
Ananta, M., Aulin, C. E., Hilborn, J., Aibibu, D., Houis, S., Brown, R. A., & Mudera, V. (2009) · Tissue Engineering Part A · doi:10.1089/ten.tea.2008.0194 · Cited by 52
“13 To benefit from the properties of natural and synthetic scaffolding materials, we fabricated a hybrid construct consisting of a warp-knitted mesh of poly(lactic acid-co-caprolactone) (PLACL) coated with compacted type I collagen gels.”
Biopolymers for Health, Food, and Cosmetic Applications
Augustine, R., Rajendran, R., Cvelbar, U., Mozetič, M., & George, A. (2013) · Wiley eBooks · doi:10.1002/9783527652457.ch27 · Cited by 63
Petrigliano, F. A., English, C. S., Barba, D., Esmende, S. M., Wu, B. M., & McAllister, D. R. (2007) · Tissue Engineering · doi:10.1089/ten.2006.0434 · Cited by 51
Lei, B., Shin, K.-H., Noh, D., Koh, Y., Choi, W., & Kim, H. (2012) · Journal of Biomedical Materials Research Part B Applied Biomaterials · doi:10.1002/jbm.b.32659 · Cited by 51
Katiyar, V., & Nanavati, H. (2010) · Polymer Chemistry · doi:10.1039/c0py00125b · Cited by 54
Copolyesters from Soybean Oil for Use as Resorbable Biomaterials
Kolanthai, E., Sarkar, K., Meka, S. R. K., Madras, G., & Chatterjee, K. (2015) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.5b00001 · Cited by 54
Endochondral Priming: A Developmental Engineering Strategy for Bone Tissue Regeneration
Freeman, F. E., & McNamara, L. M. (2016) · Tissue Engineering Part B Reviews · doi:10.1089/ten.teb.2016.0197 · Cited by 57
“46,47 54 Vascular networks have been integrated into HA ceramic scaffolds to increase bone formation.”
Three-Dimensional Printing for Craniofacial Bone Tissue Engineering
Shen, C., Witek, L., Flores, R. L., Tovar, N., Torroni, A., Coelho, P. G., Kasper, F. K., Wong, M. E., & Young, S. W. (2020) · Tissue Engineering Part A · doi:10.1089/ten.tea.2020.0186 · Cited by 53
Cortizo, M. S., Molinuevo, M. S., & Cortizo, A. M. (2008) · Journal of Tissue Engineering and Regenerative Medicine · doi:10.1002/term.62 · Cited by 51
“Although more specific in vitro and in vivo studies are needed to accurately confirm this observation, structurally related polymers did not induce inflammatory responses in in vivo studies (Gunatillake and Adhikari, 2003; Jabbari et al., 2005).”
BackgroundNanofibres and their Influence on Cells for Tissue Regeneration
Wang, Y. K., Yong, T., & Ramakrishna, S. (2005) · Australian Journal of Chemistry · doi:10.1071/ch05222 · Cited by 59
Doyle, H., Lohfeld, S., & McHugh, P. E. (2015) · Medical Engineering & Physics · doi:10.1016/j.medengphy.2015.05.009 · Cited by 50
Fabrication of Biodegradable Polyester Nanocomposites by Electrospinning for Tissue Engineering
Xing, Z., Han, S.-J., Shin, Y.-S., & Kang, I. (2011) · Journal of Nanomaterials · doi:10.1155/2011/929378 · Cited by 51
“The polyester bonds of synthetic polymers are hydrolysed in nontoxic natural metabolites and are eliminated from the body by the normal physiological processes [14].”
In vitro enzymatic degradation of the cross-linked poly(ε-caprolactone) implants
Yang, L., Li, J., Jin, Y., Li, M., & Gu, Z. (2014) · Polymer Degradation and Stability · doi:10.1016/j.polymdegradstab.2014.12.008 · Cited by 57
Sreerekha, P. R., Menon, D., Nair, S. V., & Chennazhi, K. P. (2012) · Tissue Engineering Part A · doi:10.1089/ten.tea.2012.0374 · Cited by 57
“9 13 Collagen is the most abundant constituent of the native myocardial ECM that has a bundle diameter in nanoscale dimensions.”
Kouser, S., Sheik, S., Prabhu, A., Nagaraja, G. K., Prashantha, K., D’Souza, J. N., Navada, M. K., & Manasa, D. J. (2021) · Journal of the mechanical behavior of biomedical materials/Journal of mechanical behavior of biomedical materials · doi:10.1016/j.jmbbm.2021.104441 · Cited by 50
Progress of Electrospun Fibers as Nerve Conduits for Neural Tissue Repair
ying, M., Wu, F., Lu, Y., Wei, L., & Yuan, W. (2014) · Nanomedicine · doi:10.2217/nnm.14.70 · Cited by 53
Daculsi, G., Goyenvalle, E., Cognet, R., Aguado, E., & Suokas, E. O. (2011) · Biomaterials · doi:10.1016/j.biomaterials.2011.01.033 · Cited by 51
Preparation of New α-Hydroxy Acids Derived from Amino Acids and Their Corresponding Polyesters
Cohen‐Arazi, N., Katzhendler, J., Kolitz, M., & Domb, A. J. (2008) · Macromolecules · doi:10.1021/ma8012477 · Cited by 48
Saito, E., Liu, Y., Migneco, F., & Hollister, S. J. (2012) · Acta Biomaterialia · doi:10.1016/j.actbio.2012.03.028 · Cited by 51
Levine, A. C., Heberlig, G. W., & Nomura, C. T. (2016) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2015.11.048 · Cited by 49
Morozowich, N. L., Weikel, A. L., Nichol, J. L., Chen, C., Nair, L. S., Laurencin, C. T., & Allcock, H. R. (2011) · Macromolecules · doi:10.1021/ma1027406 · Cited by 49
Artificially controlled degradable inorganic nanomaterial for cancer theranostics
Liu, Y. L., Zhang, G., Guo, Q., Ma, L., Jia, Q., Liu, L., & Zhou, J. (2016) · Biomaterials · doi:10.1016/j.biomaterials.2016.10.028 · Cited by 49
The Influence of Copolymer Composition on PLGA/nHA Scaffolds’ Cytotoxicity and In Vitro Degradation
Díaz, E., Puerto, I., Ribeiro, S., Lanceros-Méndez, S., & Barandiaran, J. M. (2017) · Nanomaterials · doi:10.3390/nano7070173 · Cited by 48
“The scaffold should ideally have a speed of degradation equal to or slightly slower than the growth of the tissue [6,9,18].”
BackgroundResultManufacturing of polycaprolactone - Graphene fibers for nerve tissue engineering
Ginestra, P. S. (2019) · Journal of the mechanical behavior of biomedical materials/Journal of mechanical behavior of biomedical materials · doi:10.1016/j.jmbbm.2019.103387 · Cited by 53
Duffy, P. E., McMahon, S., Wang, X., Keaveney, S., O’Cearbhaill, E. D., Quintana, I., Rodríguez, F. J., & Wang, W. (2019) · Biomaterials Science · doi:10.1039/c9bm00246d · Cited by 53
Advances in polymers for bio-additive manufacturing: A state of art review
Singh, N., & Singh, G. (2021) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2021.10.045 · Cited by 51
Kim, S., Tsao, H. W., Kang, Y., Young, D. A., Sen, M., Wenke, J. C., & Yang, Y. (2011) · Journal of Biomedical Materials Research Part B Applied Biomaterials · doi:10.1002/jbm.b.31909 · Cited by 50
“Generally, drug release from biodegradable polymeric devices is governed by diffusion, initial drug loading, drug/polymer interactions, drug solubility, and polymer degradation.(41) In this study, the incorporation of BMP-2 into chitosan/b-GP gels showed an initial burst release followed by a sustained release of BMP-…”
BackgroundThe Application of Biomaterials in Spinal Cord Injury
Chi, F., Deng, L. Q., Yong, Y.-Y., Wu, J., Qin, D., Yu, L., Zhou, X., & Wu, A. (2023) · International Journal of Molecular Sciences · doi:10.3390/ijms24010816 · Cited by 64
“They are well known for their high mechanical strength, flexibility, easy processing, and nontoxic degradability [144,145].”
BackgroundMonte Carlo Simulation of Degradation of Porous Poly(lactide) Scaffolds, 1: Effect of Porosity on pH
Mohammadi, Y., & Jabbari, E. (2006) · Macromolecular Theory and Simulations · doi:10.1002/mats.200600036 · Cited by 51
Advances in cellular and tissue engineering using layer‐by‐layer assembly
Shukla, A., & Almeida, B. (2014) · Wiley Interdisciplinary Reviews Nanomedicine and Nanobiotechnology · doi:10.1002/wnan.1269 · Cited by 53
Biodegradable Polymeric Films and Membranes Processing and Forming for Tissue Engineering
Suntornnond, R., An, J., Yeong, W. Y., & Chua, C. K. (2015) · Macromolecular Materials and Engineering · doi:10.1002/mame.201500028 · Cited by 55
Shell-core bi-layered scaffolds for engineering of vascularized osteon-like structures
Chen, X., Ergun, A., Gevgilili, H., Ozkan, S., Kalyon, D. M., & Wang, H. (2013) · Biomaterials · doi:10.1016/j.biomaterials.2013.07.035 · Cited by 47
“Polycaprolactone (PCL) has good biocompatibility and exhibits a relatively slow biodegradation rate that can maintain mechanical stability long enough for new bone formation [24,25].”
BackgroundSynthetic Biodegradable Polymers for Medical Applications
Suggs, L. J., Moore, S. A., & Mikos, A. G. (2007) · Springer eBooks · doi:10.1007/978-0-387-69002-5_55 · Cited by 56
Evaluation of an improved sustained-release buprenorphine formulation for use in mice
Healy, J., Tonkin, J. L., Kamarec, S. R., Saludes, M. A., Ibrahim, S. Y., Matsumoto, R. R., & Wimsatt, J. (2014) · American Journal of Veterinary Research · doi:10.2460/ajvr.75.7.619 · Cited by 51
“These polymers have been evaluated for tissue reactions and toxic effects and were found to be safe and biocompatible in humans and other animals.(27) Formulations containing N-methyl-2-pyrrolidone yield insufficient blood concentrations 72 hours after administration.”
BackgroundMohanraj, K., Sethuraman, S., & Krishnan, U. M. (2013) · Journal of Biomedical Materials Research Part B Applied Biomaterials · doi:10.1002/jbm.b.32888 · Cited by 50
Rapid duplex immunoassay for wound biomarkers at the point-of-care
Worsley, G. J., Attree, S., Noble, J. E., & Horgan, A. M. (2012) · Biosensors and Bioelectronics · doi:10.1016/j.bios.2012.02.005 · Cited by 47
“For further information regarding bioresorbable scaffolds and thermo-reversible hydrogels see Gunatillake and Adhikari (2003) and Park et al. (2011).”
BackgroundMechanical property and biocompatibility of silk fibroin–collagen type II composite membrane
Lin, X., Gao, L., Li, R., Cheng, W., Zhang, C., & Zhang, X. (2019) · Materials Science and Engineering C · doi:10.1016/j.msec.2019.110018 · Cited by 53
Electron-beam treatment of poly(lactic acid) to control degradation profiles
Cairns, M., Dickson, G. R., Orr, J., Farrar, D. F., Hawkins, K., & Buchanan, F. (2010) · Polymer Degradation and Stability · doi:10.1016/j.polymdegradstab.2010.10.016 · Cited by 51
Kim, H.-K., Jang, S.-J., Cho, Y., & Park, H. (2022) · Polymers · doi:10.3390/polym14245527 · Cited by 46
“Moreover, they have relatively good mechanical strength [7].”
BackgroundApplication of Biomimetic Cell Membrane-Coated Nanocarriers in Cardiovascular Diseases
Zhao, X., Chen, W., Wu, J., Shen, Y., Xu, B., Chen, Z., & Sun, Y. (2025) · International Journal of Nanomedicine · doi:10.2147/ijn.s531558 · Cited by 60
van Minnen, B., van Leeuwen, M. B. M., Kors, G., Zuidema, J., van Kooten, T. G., & Bos, R. R. M. (2007) · Journal of Biomedical Materials Research Part A · doi:10.1002/jbm.a.31574 · Cited by 51
Design and examination of an antioxidant-containing polyphosphazene scaffold for tissue engineering
Morozowich, N. L., Nichol, J. L., Mondschein, R. J., & Allcock, H. R. (2012) · Polymer Chemistry · doi:10.1039/c2py00570k · Cited by 47
Strategies to improve the hemocompatibility of biodegradable biomaterials
Mulinti, P., Brooks, J. E., Lervick, B., Pullan, J. E., & Brooks, A. E. (2017) · Elsevier eBooks · doi:10.1016/b978-0-08-100497-5.00017-3 · Cited by 58
Degradable and Resorbable Biomaterials
Treiser, M. D., Abramson, S. D., Langer, R., & Kohn, J. (2012) · Elsevier eBooks · doi:10.1016/b978-0-08-087780-8.00021-8 · Cited by 69
Comparative characterization of the hydrogel added PLA/β-TCP scaffolds produced by 3D bioprinting
Aydoğdu, M. O., Öner, E. T., Ekren, N., Erdemir, G., Kuruca, S. E., Yuca, E., Bostan, M. S., Eroğlu, M. S., Ikram, F., Uzun, M., et al. (2019) · Bioprinting · doi:10.1016/j.bprint.2019.e00046 · Cited by 54
Kinaci, A., & van Doormaal, T. P. C. (2019) · Expert Review of Medical Devices · doi:10.1080/17434440.2019.1626232 · Cited by 51
Biodegradable polymers for drug delivery systems
Kwon, G. S., & Furgeson, D. Y. (2007) · Elsevier eBooks · doi:10.1533/9781845693640.83 · Cited by 59
Parlak, M. E., Şahin, O. I., Dündar, A. N., Sarıcaoğlu, F. T., Smaoui, S., Gökşen, G., Koirala, P., Al‐Asmari, F., & Nirmal, N. P. (2023) · Food Chemistry · doi:10.1016/j.foodchem.2023.138160 · Cited by 59
Caracciolo, P. C., de Queiroz, A. A. A., Higa, O. Z., Buffa, F., & Abraham, G. A. (2008) · Acta Biomaterialia · doi:10.1016/j.actbio.2008.02.016 · Cited by 45
Grzesiak, J., Marycz, K., Szarek, D., Bednarz, P., & Laska, J. (2015) · Materials Science and Engineering C · doi:10.1016/j.msec.2015.03.050 · Cited by 46
Leonida, A., Paiusco, A., Rossi, G., et al. (2012) · Lasers in Medical Science · doi:10.1007/s10103-012-1067-6 · Cited by 45
“An increasing number of biomaterials have been proposed as scaffolds for tissue regeneration, aiming to recreate the environment where the complex interaction between cells and their matrix occurs [14–16].”
BackgroundTissue Engineered Airways: A Prospects Article
Bogan, S. L., Teoh, G. Z., & Birchall, M. (2016) · Journal of Cellular Biochemistry · doi:10.1002/jcb.25512 · Cited by 45
“, 2015], resorbable sutures, drug delivery systems, orthopedic fixtures [Gunatillake et al., 2003], artificial skin, even bone substitutes [Armentano et al.”
BackgroundMethodInfluentialSelf-neutralizing PLGA/magnesium composites as novel biomaterials for tissue engineering
Xu, T. O., Kim, H. S., Stahl, T., & Nukavarapu, S. P. (2018) · Biomedical Materials · doi:10.1088/1748-605x/aaaa29 · Cited by 46
“Synthetic biomaterials include polyesters, polyurethanes, polyanhydrides, polyamides and polyphosphazenes [2, 3].”
BackgroundBhagabati, P. (2020) · Elsevier eBooks · doi:10.1016/b978-0-12-816789-2.00009-2 · Cited by 45
Hacker, M. C., & Mikos, A. G. (2010) · Elsevier eBooks · doi:10.1016/b978-0-12-381422-7.10033-1 · Cited by 74
Hemmrich, K., Salber, J., Meersch, M., Wiesemann, U., Gries, T., Pallua, N., & Klee, D. (2007) · Journal of Materials Science Materials in Medicine · doi:10.1007/s10856-006-0048-3 · Cited by 45
Emulsion-based synthesis of PLGA-microspheres for the in vitro expansion of porcine chondrocytes
Gabler, F., Frauenschuh, S., Ringe, J., et al. (2007) · Biomolecular Engineering · doi:10.1016/j.bioeng.2007.08.013 · Cited by 45
Doyle, H., Lohfeld, S., & McHugh, P. E. (2013) · Annals of Biomedical Engineering · doi:10.1007/s10439-013-0913-4 · Cited by 47
Pankajakshan, D., Pampadykandathil, L. P., Palakkal, M., Krishnan, K., & Krishnan, L. K. (2008) · Journal of Biomedical Materials Research Part B Applied Biomaterials · doi:10.1002/jbm.b.31146 · Cited by 48
“An ideal scaffold must satisfy a number of requirements such as biocompatibility, appropriate mechanical properties, and biodegradation to nontoxic products within the time frame required for application in addition to processability of complicated shapes with optimum porosity and ability to support cell growth and pr…”
BackgroundWu, H., Wang, X., Wang, G., Yuan, G., Jia, W., Tian, L., Zheng, Y., Ding, W., & Jia, P. (2024) · Advanced Materials · doi:10.1002/adma.202407040 · Cited by 59
Advances and Prospects in Tissue-Engineered Meniscal Scaffolds for Meniscus Regeneration
Guo, W., Liu, S., Zhu, Y. X., Yu, C., Lu, S., Yuan, M., Gao, Y., Huang, J., Yuan, Z., Peng, J. C., et al. (2015) · Stem Cells International · doi:10.1155/2015/517520 · Cited by 54
“Bioabsorbable synthetic polymers, such as polyurethane (PU), polyglycolic acid (PGA), polylactic acid, and poly (εcaprolactone) (PCL), are widely used and have played a key role creating meniscal scaffolds [49].”
BackgroundSynthesis of high molecular weight polyglycolide in supercritical carbon dioxide
Schmidt, C., Behl, M., Lendlein, A., & Beuermann, S. (2014) · RSC Advances · doi:10.1039/c4ra06815g · Cited by 46
Chun, Y. W., Khang, D., Haberstroh, K. M., & Webster, T. (2009) · Nanotechnology · doi:10.1088/0957-4484/20/8/085104 · Cited by 44
Fernández, J., Etxeberria, A., & Sarasua, J.-R. (2015) · European Polymer Journal · doi:10.1016/j.eurpolymj.2015.09.001 · Cited by 44
Fabrication of FGF-2 immobilized electrospun gelatin nanofibers for tissue engineering
Lee, H., Lim, S., Birajdar, M. S., Lee, S., & Park, H. (2016) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2016.07.041 · Cited by 46
Understanding and utilizing the biomolecule/nanosystems interface
Chen, E. Y., Liu, W. F., Megido, L., Díez, P., Fuentes, M., Fager, C., Olsson, E., Gessner, I., & Mathur, S. (2017) · Elsevier eBooks · doi:10.1016/b978-0-323-48063-5.00003-4 · Cited by 62
Materials and Manufacturing Techniques for Polymeric and Ceramic Scaffolds Used in Implant Dentistry
Özcan, M., Hotza, D., Fredel, M. C., da Cruz, A. C. C., & Volpato, C. Â. M. (2021) · Journal of Composites Science · doi:10.3390/jcs5030078 · Cited by 48
“The rate of scaffold degradation is determined by factors such as the configurational structure, crystallinity, molecular weight, morphology, stresses, porosity, and implantation site [86].”
BackgroundLiu, Q., Tian, M., Ding, T., et al. (2005) · Journal of Applied Polymer Science · doi:10.1002/app.22397 · Cited by 44
Nanotechnology for the Regeneration of Hard and Soft Tissues
Webster, T. J. (2007) · WORLD SCIENTIFIC eBooks · doi:10.1142/6421 · Cited by 49
Zakhem, E., & Bitar, K. N. (2015) · Journal of Functional Biomaterials · doi:10.3390/jfb6040999 · Cited by 43
“Additionally, disadvantages include degradability byproducts and variation in mechanical properties which can be limiting in certain applications [20].”
BackgroundHaque, P., Parsons, A. J., Barker, I. A., Ahmed, I., Irvine, D. J., Walker, G. S., & Rudd, C. D. (2010) · Composites Science and Technology · doi:10.1016/j.compscitech.2010.06.012 · Cited by 52
“PLA degrades to form lactic acid which is normally present in the body [6].”
BackgroundMolladavoodi, S., Gorbet, M., Medley, J. B., & Kwon, H. (2012) · Journal of the mechanical behavior of biomedical materials/Journal of mechanical behavior of biomedical materials · doi:10.1016/j.jmbbm.2012.08.021 · Cited by 42
“The lactic acid formed in the body enters the tricarboxylic acid cycle and breaks down to water and carbon dioxide (Gunatillake and Adhikari, 2003).”
BackgroundSantiago‐Rodríguez, L., Lafontaine, M. M., Castro, C. I., Méndez-Vega, J., Latorre‐Esteves, M., Juan, E. J., Mora, E., Torres‐Lugo, M., & Rinaldi, C. (2013) · Journal of Materials Chemistry B · doi:10.1039/c3tb20256a · Cited by 45
Carrubba, V. L., Pavia, F. C., Brucato, V., & Piccarolo, S. (2008) · International Journal of Material Forming · doi:10.1007/s12289-008-0332-5 · Cited by 45
Polymeric hollow fiber membranes for bioartificial organs and tissue engineering applications
Diban, N., & Stamatialis, D. (2014) · Journal of Chemical Technology & Biotechnology · doi:10.1002/jctb.4300 · Cited by 43
PEGylated boron nitride nanotube-reinforced poly(propylene fumarate) nanocomposite biomaterials
Diez-Pascual, A. M., & Díez-Vicente, A. L. (2016) · RSC Advances · doi:10.1039/c6ra09884c · Cited by 46
Wang, Z., Wang, S., Marois, Y., Guidoin, R., & Zhang, Z. (2005) · Biomaterials · doi:10.1016/j.biomaterials.2005.05.058 · Cited by 46
Thijssen, Q., Parmentier, L., Augustyniak, E. M., Mouthuy, P., & Vlierberghe, S. V. (2022) · Advanced Functional Materials · doi:10.1002/adfm.202108869 · Cited by 44
Hecko, S., Schiefer, A., Badenhorst, C. P. S., Fink, M. J., Mihovilovič, M. D., Bornscheuer, U. T., & Rudroff, F. (2023) · Chemical Reviews · doi:10.1021/acs.chemrev.2c00304 · Cited by 53
Yu, H., Won, J., Jin, G., & Kim, H. (2012) · BioResearch open access · doi:10.1089/biores.2012.0234 · Cited by 46
Biomimetic and synthetic esophageal tissue engineering
Jensen, T., Blanchette, A. E., Vadasz, S., Dave, A., Canfarotta, M. W., Sayej, W. N., & Finck, C. M. (2015) · Biomaterials · doi:10.1016/j.biomaterials.2015.04.004 · Cited by 44
“degradation rate in the human body [39].”
MethodhiPS-MSCs differentiation towards fibroblasts on a 3D ECM mimicking scaffold
Xu, R., Taskin, M. B., Rubert, M., Seliktar, D., Besenbacher, F., & Chen, M. (2015) · Scientific Reports · doi:10.1038/srep08480 · Cited by 44
“We gratefully acknowledge the funding for project ElectroMed (11-115313) from the”
BackgroundBone Tissue Engineering Challenges in Oral & Maxillofacial Surgery
Smith, B. T., Shum, J., Wong, M. E.-K., Mikos, A. G., & Young, S. W. (2015) · Advances in experimental medicine and biology · doi:10.1007/978-3-319-22345-2_4 · Cited by 46
Pedersen, T. Ø., Blois, A. L., Xing, Z., Xue, Y., Sun, Y., Finne‐Wistrand, A., Akslen, L. A., Lorens, J. B., Leknes, K. N., Fristad, I., et al. (2013) · Stem Cell Research & Therapy · doi:10.1186/scrt202 · Cited by 45
“The potential use of biodegradable polymers as scaffolds for cell-based tissue regeneration was reviewed by Gunatillake and Adhikari [18].”
BackgroundDomján, A., Fodor, C., Kovács, S., Marek, T., Iván, B., & Süvegh, K. (2012) · Macromolecules · doi:10.1021/ma301533g · Cited by 42
Metadata
- Authors
- CSIRO Molecular Science, B. 1., & Gunatillake, P.
- Corresponding author
- CSIRO Molecular Science, Bag 10, Clayton South MDC, Vic 3169, Australia
- Venue
- European Cells and Materials
- Publisher
- Forum Multimedia Publishing LLC
- Published
- 2003-10-01
- Volume
- 5
- Pages
- 1-16
- ISSN
- 1473-2262 (ISSN-L)
- OpenAlex
- W2106035984
- Cited by
- 1,765
- References
- 97
- Citations by year
- 2026: 43 · 2025: 61 · 2024: 59 · 2023: 80 · 2022: 90 · 2021: 112 · 2020: 102 · 2019: 115 · 2018: 105 · 2017: 128 · 2016: 110 · 2015: 106 · 2014: 110 · 2013: 91 · 2012: 86
- FWCI
- 1.32
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- cc-by
- Locations
- European Cells and Materials (publishedVersion, cc-by)
- PubMed (publishedVersion)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion)
- Topics
- Physical Sciences › Materials Science › Biomaterials › biodegradable polymer synthesis and properties
- Physical Sciences › Engineering › Biomedical Engineering › Bone Tissue Engineering Materials
- Health Sciences › Medicine › Surgery › Surgical Sutures and Adhesives
- Keywords
- tissue engineering, polyesters, polyglycolic acid, polylactic acid, polyanhydrides, polyphosphazenes, polyurethane, poly(propylene fumarate), injectable polymers, orthopedic tissue engineering, biodegradation, biocompatibility, degradation products
- MeSH terms
- Biocompatible Materials, Models, Chemical, Polymers, Tissue Engineering
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.