CoChat
Sign Up
PreprintCited by 2Fusion materials and technologiesSuperconducting Materials and ApplicationsNuclear materials and radiation effects

A facility for thermo-mechanical characterization of fusion magnet materials during cryogenic ion irradiation

Open access
Aurora, Akarsh, Devitre, Alexis R, Wylie, Angus PC, Rajagopal, Jonas A, Short, Michael P·2025·arXiv
DOI 10.48550/arxiv.2506.17358arXiv 2506.17358
Open this paper in CoChat — free account

Abstract

Commercial fusion power plants demand magnet materials that retain structural integrity and thermal conductivity while operating under the bombardment of energetic neutrons at cryogenic temperatures. Understanding how thermo-mechanical properties evolve under such extreme loads is crucial for selecting materials with high radiation tolerance and predictable failure mechanisms. Presented here is a facility that combines cryogenic transient grating spectroscopy (TGS) with simultaneous ion irradiation, enabling in-situ measurements of thermal diffusivity and surface acoustic wave (SAW) frequency spectra. Employing copper as a benchmark material, an irradiation was performed at 30 K with 12.4 MeV $\text{Cu}^{6+}$ ions producing a final fluence of $1.9 \times 10^{17}$ ions/m$^2$. Over the irradiation period, thermal diffusivity nearly halved from an initial value of $1.2 \times 10^{-4}$ $\text{m}^2/\text{s}$ while SAW speed did not show significant change, maintaining a value of $2162\pm18$ m/s. Given its real-time monitoring capability and the numerous candidate materials that remain uncharacterized under fusion magnet operating conditions, this facility is poised to deliver new scientific insights into fusion magnet material degradation trends, contributing to improved design criteria and operational certainty for forthcoming fusion power plants.

AI snapshot

Written from the paper’s full text.

TL;DR

The paper presents a facility that combines cryogenic transient grating spectroscopy (TGS) with simultaneous ion irradiation to measure thermo-mechanical property evolution in fusion magnet materials. Using Cu-110 as a benchmark, it demonstrates in-situ thermal diffusivity and surface acoustic wave measurements during 30 K self-ion irradiation.

Key findings

  • Cu-110 was irradiated at 30 K with 12.4 MeV Cu⁶⁺ ions to a final fluence of 1.9 × 10¹⁷ ions/m², equivalent to 21 mdpa.
  • Thermal diffusivity nearly halved from an initial 1.2 × 10⁻⁴ m²/s, decaying to a plateau of 0.7 ± 0.22 × 10⁻⁴ m²/s.
  • SAW speed showed no significant change, maintaining 2162 ± 18 m/s in the abstract; the text reports an initial 2155 ± 7.2 m/s and an average maximum of 2180 ± 8.0 m/s at 1.4 × 10¹⁷ ions/m².
  • At 0.6 × 10¹⁷ ions/m², corresponding to 6 mdpa, thermal diffusivity at 30 K deteriorated by 17.9 ± 6.75%.

Methods

  • The apparatus combines a cryogenic target holder, TGS optics, and an ion-beam accelerator, operating from 30 K to 300 K with a base temperature of 30 K and a 3-hour cooldown from room temperature.
  • TGS used a 532 nm pump laser at 1 kHz and a 577 nm quasi-continuous probe beam; the true grating spacing was calibrated to 3.5276 µm using a {100} single-crystal tungsten reference.
  • A 13 mm × 15 mm × 2 mm polycrystalline Cu-110 sample was irradiated using the MIT CLASS 1.7 MV Tandetron with 12.4 MeV Cu⁶⁺ ions at an average beam current of 0.45 nA; SRIM was used to compute displacement damage.

Limitations

  • The paper states that absolute TGS calibration can be influenced by beam-spot alignment, surface impurities, and other systematic effects, and that the measured pre-irradiation diffusivity is about an order of magnitude below literature values for Cu with RRR=30.
  • The paper states that localized ion beam heating can be consequential and is not fully captured by nearby temperature probes, but precise accountancy of ion beam point heating is beyond the scope of the work.
  • The paper states that the analytical heat-load calculation overestimates sample temperature by approximately 10 K due to room-temperature emissivity assumptions and perfect absorptivity, and that MLI was not used in further experiments because it restricted target-holder movement during alignment.
  • Evident from the text: the demonstration is limited to one benchmark material, Cu-110, and one irradiation condition, so broader material and dose-temperature trends are not established.

Model-written summary. Check it against the paper before relying on it.

Integrity signals

Registry

DataCite · 10.48550/arxiv.2506.17358

Cites

47 of 47 references verified0 citation errors · 0 not checkable

Statistics

Nothing to recompute.

Claims the paper makes

23 of 55 cited sources checked · 10 supported · 1 flagged · accuracy not yet measured

  • Premisecitation
    § 1. Introduction · p. 3

    Cu-110 was selected as a benchmark material for its crucial role in REBCO HTS magnets and cables.

    “Cu-110 was selected as a benchmark material for its crucial role in REBCO HTS magnets and cables [24, 25].”
    Quote in the paperSubstantial claim1 of 2 sources checked
    • cites [24] [24] ZS Hartwig, RF Vieira, BN Sorbom, RA Badcock, M Bajko, WK Beck, B Castaldo, CL Craighill, M Davies, J Estrada, et al. Viper: an industrially scalable high-current high-temperature superconductor cable. Superconductor Science and Technology , 33(11):11LT01, 2020. - source

      The Cable design section (page unavailable) describes a copper core supporting HTS stacks and a copper former providing a heat-removal path. The Cryostability & quench section also identifies the former’s heat capacity and low electrical resistance as contributors to cable stability. These passages support an important role for copper in HTS cables, but the paper does not identify the copper as Cu-110 or establish a role for that specific grade in REBCO magnets. (LLM, conf=0.86)

      Experimental — accuracy not yet measured
    • cites [25] [25] ZS Hartwig et al. The sparc toroidal field model coil program. IEEE Transactions on Applied Superconductivity , 34(2):1-16, 2024. - source
  • Study design and conductcitation
    § 2.1. Transient grating spectroscopy (TGS · p. 5

    Calibration using a {100}-oriented single crystal tungsten reference specimen with SAW speed 2669.5 m/s revealed a true grating spacing of 3.5276 μm.

    “Calibration using a { 100 } -oriented single crystal tungsten reference specimen (SAW speed: 2669.5 m/s) revealed a true grating spacing of 3.5276 µ m [15].”
    Quote in the paperSubstantial claim1 of 1 sources checked
    • cites [15] [15] CA Dennett, P Cao, SE Ferry, A Vega-Flick, AA Maznev, KA Nelson, AG Every, and MP Short. Bridging the gap to mesoscale radiation materials science with transient grating spectroscopy. Phys. Rev. B , 94:214106, 2016. - source

      Section A (Experiment; page not provided) says a {001}-oriented single-crystal tungsten specimen was used to calibrate grating spacing. It gives the reference SAW speed as 2665.9 m/s, not 2669.5 m/s, and does not report a grating spacing of 3.5276 μm. (LLM, conf=0.91)

      Experimental — accuracy not yet measured
  • Premisecitation
    § 1. Introduction · p. 2

    The expected cumulative radiation dose that REBCO can withstand over its operational lifetime in fusion magnets is greater than 4 mdpa.

    “This threshold is especially relevant because it is the expected cumulative radiation dose that rare-earth barium copper oxide (REBCO)-the primary constituent of hightemperature superconducting (HTS)-can withstand over their operational lifetime in fusion magnets [4].”
    Quote in the paperSubstantial claim1 of 1 sources checked
    • cites [4] [4] W Iliffe, N Peng, G Brittles, R Bateman, R Webb, C Grovenor, and S Speller. In-situ measurements of the effect of radiation damage on the superconducting properties of coated conductors. Superconductor Science and Technology , 34(9):09LT01, 2021. - source

      The Abstract reports irradiation of GdBCO coated conductors up to 4 mdpa, and the Introduction identifies REBCO as a material for fusion magnets. Neither passage establishes that REBCO can withstand more than 4 mdpa over a magnet’s operational lifetime. The Conclusions say further work is needed to understand the practical implications for fusion magnets. (LLM, conf=0.85)

      Experimental — accuracy not yet measured
  • Premisecitation
    § 1. Introduction · p. 2

    Among techniques that provide local structural information during irradiation, such as in situ TEM and in situ Raman spectroscopy, TGS is unique in its ability to continuously monitor thermal and elastic properties.

    “And amongst techniques such as in situ TEM [9] or in situ Raman spectroscopy [10] that can provide local structural information during irradiation, TGS is unique in its ability to continuously monitor thermal and elastic properties.”
    Quote in the paperSubstantial claim1 of 2 sources checked
    • cites [9] [9] K Hattar, DC Bufford, and DL Buller. Concurrent in situ ion irradiation transmission electron microscope. Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms , 338:56-65, 2014. - source
    • cites [10] [10] S Miro, E Bordas, L Thom´ e, JM Costantini, F Leprˆ etre, P Trocellier, Y Serruys, L Beck, D Gosset, R Verlet, J Huguet-Garcia, M Tupin, and M Belleil. Monitoring of the microstructure of ion-irradiated nuclear ceramics by in situ raman spectroscopy. Journal of Raman Spectroscopy , 47(5):476-485, 2016. - source
  • Study design and conductcitation
    § 3.1. Thermal property evolution · p. 10

    A two-step fitting approach improved both thermal and functional fitting sensitivity compared to existing techniques, especially in cases with noisy or rapid signal decay.

    “This approach improved both thermal and functional fitting sensitivity compared to existing techniques [16, 31], especially in cases with noisy or rapid signal decay.”
    Quote in the paperSubstantial claim2 of 2 sources checked
    • cites [16] [16] APC Wylie, KB Woller, SAA Al Dajani, BR Dacus, EJ Pickering, M Preuss, and MP Short. Thermal diffusivity in ion-irradiated single-crystal iron, chromium, vanadium, and tungsten measured using transient grating spectroscopy. Journal of Applied Physics , 132(4):045102, 2022. - source

      The available passages are bibliographic metadata (section “2 Finished”) and an access-to-document listing (section “Abstract”); neither discusses fitting performance. Searches for two-step fitting, sensitivity, noise, and rapid signal decay found no passage addressing the claim. (LLM, conf=0.76)

      Experimental — accuracy not yet measured
    • cites [31] [31] CA. Dennett and MP Short. Thermal diffusivity determination using heterodyne phase insensitive transient grating spectroscopy. Journal of Applied Physics , 123(21):215109, 2018. - source

      In Results and Discussion (page unavailable), fitting with an added decaying sinusoidal term reduced variation in the fitted thermal diffusivity from 9.3% to 3.5% compared with the simpler fit. Parameter Estimation also describes preliminary fitting to improve starting values. These passages support an improvement in thermal-diffusivity fitting, but do not establish improved functional fitting sensitivity or a particular advantage for noisy or rapidly decaying signals. (LLM, conf=0.82)

      Experimental — accuracy not yet measured
  • Classified as probably not a substantial claim. 15
  • May combine two claims. 30

  • Probably not a substantial claim: may not pass S3 (load-bearing).

    Premisecitation
    § 1. Introduction · p. 2

    In situ ion irradiation with TGS has been introduced to infer bulk property changes as they occur, enabling quantification of relationships between dose and void swelling, elastic moduli, and thermal diffusivity in single-crystal metals.

    “Short and Dennett et al. [13, 7] introduced in situ ion irradiation with TGS to infer bulk property changes as they occur, enabling the quantification of relationships between dose and void swelling [14], elastic moduli [15], and thermal diffusivity [16] in single-crystal metals.”
    Quote in the paperNot a substantial claim2 of 4 sources checked
    • cites [13] [13] MP Short, CA Dennett, SE Ferry, et al. Applications of transient grating spectroscopy to radiation materials science. JOM , 67(8):1840-1848, 2015. - source
    • cites [7] [7] CA Dennett, DL Buller, K Hattar, and MP Short. Real-time thermomechanical property monitoring during ion beam irradiation using in situ transient grating spectroscopy. Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms , 440:126-138, 2019. - source
    • cites [14] [14] CA Dennett, KP So, A Kushima, DL Buller, K Hattar, and MP Short. Detecting self-ion irradiation-induced void swelling in pure copper using transient grating spectroscopy. Acta Materialia , 145:496-503, 2018. - source

      The Experimental methods section explicitly says the irradiated samples were characterized ex situ using TGS. The Discussion describes in situ use as a future development, not something this paper introduced or used to quantify changes as they occurred. The later claims about dose relationships have separate citations in the citing sentence. (LLM, conf=0.88)

      Checked by a reasoning model — may be wrong.

      Experimental — accuracy not yet measured
    • cites [15] [15] CA Dennett, P Cao, SE Ferry, A Vega-Flick, AA Maznev, KA Nelson, AG Every, and MP Short. Bridging the gap to mesoscale radiation materials science with transient grating spectroscopy. Phys. Rev. B , 94:214106, 2016. - source

      The Introduction and Background says TGS was previously proposed for in situ monitoring during ion irradiation; this paper tests its sensitivity to small changes in surface acoustic wave speed. The Conclusions describes monitoring properties as irradiation takes place as a future development, not an in situ experiment demonstrated here. Its simulations relate vacancy concentration to acoustic response, but do not quantify dose relationships for void swelling, elastic moduli, and thermal diffusivity. (LLM, conf=0.87)

      Experimental — accuracy not yet measured

  • May combine two claims.

    Premisecitation
    § 2.1. Transient grating spectroscopy (TGS · p. 3

    TGS is a non-contact method for characterizing changes in elastic, acoustic, and thermal transport properties, making it a powerful tool for inferring material structure evolution.

    “TGS is a non-contact method for characterizing changes in elastic, acoustic, and thermal transport properties, making it a powerful tool for inferring material structure evolution [8].”
    Quote in the paperSubstantial claim1 of 1 sources checked
    • cites [8] [8] F Hofmann, MP Short, and CA Dennett. Transient grating spectroscopy: An ultrarapid, nondestructive materials evaluation technique. MRS Bulletin , 44:392402, 2019. - source

  • Probably not a substantial claim: may not pass S3 (load-bearing). May combine two claims.

    Premisecitation
    § 2.2. Cryogenic target holder · p. 7

    Localized ion beam heating effects can be consequential; the temperature rise in the beam spot is not fully captured by nearby temperature probes and requires alternative means of quantification.

    “Localized ion beam heating effects, on the other hand, can be consequential; as is shown in a recent publication [32], the temperature rise in the beam spot is not fully captured by nearby temperature probes and requires alternative means of quantification.”
    Quote in the paperNot a substantial claim1 of 1 sources checked
    • cites [32] [32] AR Devitre, DX Fischer, N Riva, M Rae, LD Kortman, KB Woller, ZL Fisher, MP Short, DG Whyte, and ZS Hartwig. Beam heating explains critical current suppression measured during ion irradiation of rebco tapes. Superconductor Science and Technology , 38(1):015005, 2025. - source

  • May combine two claims.

    Premisecitation
    § 1. Introduction · p. 2

    TGS provides rapid, non-destructive diagnoses of thermomechanical properties and operates on the length scales of ion irradiation damage.

    “TGS is an optical technique that provides rapid diagnoses of thermomechanical properties, is inherently non-destructive, and operates on the length scales of ion irradiation damage [7, 8].”
    Quote in the paperSubstantial claim1 of 2 sources checked
    • cites [7] [7] CA Dennett, DL Buller, K Hattar, and MP Short. Real-time thermomechanical property monitoring during ion beam irradiation using in situ transient grating spectroscopy. Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms , 440:126-138, 2019. - source
    • cites [8] [8] F Hofmann, MP Short, and CA Dennett. Transient grating spectroscopy: An ultrarapid, nondestructive materials evaluation technique. MRS Bulletin , 44:392402, 2019. - source

  • May combine two claims.

    Premisecitation
    § 1. Introduction · p. 2

    TGS enables in situ measurements during irradiation, unlike traditional ex situ approaches such as nanoindentation, X-ray diffraction, or TEM.

    “Unlike traditional ex situ approaches-such as nanoindentation, X-ray diffraction, or TEM-that cannot easily operate in extreme irradiation environments, TGS enables in situ measurements.”
    Quote in the paperSubstantial claim1 of 2 sources checked
    • cites [7] [7] CA Dennett, DL Buller, K Hattar, and MP Short. Real-time thermomechanical property monitoring during ion beam irradiation using in situ transient grating spectroscopy. Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms , 440:126-138, 2019. - source
    • cites [8] [8] F Hofmann, MP Short, and CA Dennett. Transient grating spectroscopy: An ultrarapid, nondestructive materials evaluation technique. MRS Bulletin , 44:392402, 2019. - source

      In “Probing material evolution via elastic properties” (page unavailable), the paper describes TGS measurements made during ion-beam irradiation and contrasts them with slower traditional post-irradiation examination. It does not establish that all three named methods cannot easily operate during irradiation; it also cites in situ TEM observations. The comparison with those specific methods is therefore broader than the source supports. (LLM, conf=0.84)

      Experimental — accuracy not yet measured

  • Probably not a substantial claim: may not pass S3 (load-bearing).

    Premisecitation
    § 1. Introduction · p. 3

    VIPER cables operating at 20 K exhibit high cryostability, benefiting from copper specific heats and thermal conductivities.

    “For example, VIPER cables (operating at 20 K) exhibit high cryostability, benefiting from copper specific heats and thermal conductivities.”
    Quote in the paperNot a substantial claim1 of 2 sources checked
    • cites [24] [24] ZS Hartwig, RF Vieira, BN Sorbom, RA Badcock, M Bajko, WK Beck, B Castaldo, CL Craighill, M Davies, J Estrada, et al. Viper: an industrially scalable high-current high-temperature superconductor cable. Superconductor Science and Technology , 33(11):11LT01, 2020. - source
    • cites [25] [25] ZS Hartwig et al. The sparc toroidal field model coil program. IEEE Transactions on Applied Superconductivity , 34(2):1-16, 2024. - source

  • May combine two claims.

    Premisecitation
    § 1. Introduction · p. 2

    The relevant literature has primarily focused on the electrical properties of magnet materials, leaving a notable gap in understanding thermo-mechanical property evolution under fusion power plant operating conditions.

    “The relevant literature has primarily focused on the electrical properties of magnet materials [3, 4, 5], leaving a notable gap in the understanding of thermo-mechanical property evolution under FPP operating conditions.”
    Quote in the paperSubstantial claim2 of 3 sources checked
    • cites [3] [3] AR Devitre, DX Fischer, KB Woller, BC Clark, MP Short, DG Whyte, and ZS Hartwig. A facility for cryogenic ion irradiation and in situ characterization of rare-earth barium copper oxide superconducting tapes. Review of Scientific Instruments , 95(6):063907, 2024. - source
    • cites [4] [4] W Iliffe, N Peng, G Brittles, R Bateman, R Webb, C Grovenor, and S Speller. In-situ measurements of the effect of radiation damage on the superconducting properties of coated conductors. Superconductor Science and Technology , 34(9):09LT01, 2021. - source
    • cites [5] [5] DX Fischer, R Prokopec, J Emhofer, and M Eisterer. The effect of fast neutron irradiation on the superconducting properties of rebco coated conductors with and without artificial pinning centers. Superconductor Science and Technology , 31(4):044006, 2018. - source

  • Probably not a substantial claim: may not pass S3 (load-bearing).

    Premisecitation
    § 1. Introduction · p. 2

    Prior art on cryogenic TGS investigated thermal, spin, and acoustic transport property evolution in several solid-state materials.

    “Separately, prior art on cryogenic TGS investigated thermal [17], spin [18], and acoustic [19, 20] transport property evolution in several solid-state materials [21].”
    Quote in the paperNot a substantial claim2 of 4 sources checked
    • cites [17] [17] DM Pennington and CB Harris. Dynamics of surface thermal expansion and diffusivity using two-color reflection transient gratings. In Proc. SPIE 1856, Laser Radiation Photophysics , 1993. - source
    • cites [18] [18] F Mahmood, Z Alpichshev, YH Lee, J Kong, and N Gedik. Observation of exciton-exciton interaction mediated valley depolarization in monolayer MoSe2. Nano Letters , 18(1):223-228, 2018. - source
    • cites [19] [19] K Kim. Investigation of Transport Phenomena of Thermal Acoustic Excitations in Semi-Crystalline and Amorphous Materials Using Transient Grating Spectroscopy . Dissertation, California Institute of Technology, 2021. -

      Couldn’t be matched to a paper in Crossref, so it can’t be checked.

    • cites [20] [20] S Huberman et al. Observation of second sound in graphite at temperatures above 100 k. Science , 364:375-379, 2019. - source

  • May combine two claims.

    Findingcitation
    § 3.1. Thermal property evolution · p. 9

    Thermal diffusivity of Cu-110 decreases as radiation damage accumulates, consistent with previous high-temperature irradiation studies on copper and other mono-atomic metals.

    “Consistent with previous high-temperature irradiation studies on copper [35] and other mono-atomic metals [16, 36], thermal diffusivity decreases as radiation damage accumulates (Figure 5).”
    Quote in the paperNot a substantial claim1 of 3 sources checked
    • cites [35] [35] E Trachanas, A Wylie, A Bignami, N Gazis, MP Short, K Michel, C Alwmark, E Gazis, G Fikioris, and H Danared. Study of thermal diffusivity degradation on cu-ofe copper due to proton and self-ion irradiation using in situ transient grating spectroscopy. Journal of Nuclear Materials , 607:155674, 2025. - source
    • cites [16] [16] APC Wylie, KB Woller, SAA Al Dajani, BR Dacus, EJ Pickering, M Preuss, and MP Short. Thermal diffusivity in ion-irradiated single-crystal iron, chromium, vanadium, and tungsten measured using transient grating spectroscopy. Journal of Applied Physics , 132(4):045102, 2022. - source

      The title and bibliographic entry (section ‘2 Finished’; no page given) identify a study of thermal diffusivity in ion-irradiated iron, chromium, vanadium, and tungsten, but provide no findings. Searches for a dose-dependent decrease and high-temperature irradiation returned no results passages, so our copy cannot verify the trend attributed to this source. (LLM, conf=0.70)

      Experimental — accuracy not yet measured
    • cites [36] [36] J Habainy, Y Dai, Y Lee, and S Iyengar. Thermal diffusivity of tungsten irradiated with protons up to 5.8 dpa. Journal of Nuclear Materials , 509:152-157, 2018. - source
    • Rests on an assumption: The sample temperature during irradiation is 30 K, or the measured temperature is representative of the irradiated region.

  • Probably not a substantial claim: may not pass S3 (load-bearing).

    Premisecitation
    § 1. Introduction · p. 2

    TGS has previously been employed in tandem with ion-beam accelerators that emulate neutron irradiation.

    “Previously, TGS has been employed in tandem with ion-beam accelerators that emulate neutron irradiation [11, 12].”
    Quote in the paperNot a substantial claim2 of 2 sources checked
    • cites [11] [11] GS Was, Z Jiao, E Getto, K Sun, AM Monterrosa, SA Maloy, O Anderoglu, BH Sencer, and M Hackett. Emulation of reactor irradiation damage using ion beams. Scripta Materialia , 88:33-36, 2014. - source

      The paper’s Abstract says ion irradiation can serve as a surrogate for neutron irradiation and describes accelerator-based experiments that emulate reactor damage. It does not mention TGS or show that TGS was employed alongside an ion-beam accelerator; searches for TGS and transient grating spectroscopy found no such passage. The page number is unavailable in our copy. (LLM, conf=0.86)

      Experimental — accuracy not yet measured
    • cites [12] [12] F Hofmann, D Mason, J Eliason, et al. Non-contact measurement of thermal diffusivity in ion-implanted nuclear materials. Scientific Reports , 5:16042, 2015. - source

  • May combine two claims.

    Premisecitation
    § 3.1. Thermal property evolution · p. 11

    Reasonable radiation operation limits for copper in YBCO HTS magnets are fast neutron fluences up to 2×10^21 n/m2, corresponding to damage levels in the range of mdpa.

    “Reasonable radiation operation limits for copper in Yttrium Barium Copper-Oxide (YBCO) HTS magnets are fast neutron fluences up to 2 × 10 21 n / m 2 , corresponding to damage levels in the range of mdpa [43].”
    Quote in the paperSubstantial claim1 of 1 sources checked
    • cites [43] [43] Y Zhai, P Titus, C Kessel, and L El-Guebaly. Conceptual magnet design study for fusion nuclear science facility. Fusion Engineering and Design , 135, Part B:324-336, 2018. - source

      Table 10 in §8, Radiation Limits (p. 7), lists a fast-neutron-fluence limit of 2×10^21 n/m² for copper in the paper’s discussion of magnet materials. The paper does not state that this fluence corresponds to damage in the mdpa range; that part of the claim is unsupported by our copy. (LLM, conf=0.88)

      Experimental — accuracy not yet measured

  • May combine two claims.

    Findingown data
    § 2.3. Cu-110 irradiation case study · p. 8

    Irradiation of Cu-110 with 12.4 MeV Cu6+ ions at 30 K for 30 minutes resulted in a total fluence of 1.9 × 10^17 ions/m^2, equivalent to 21 mdpa.

    “Irradiation commenced alongside TGS at 30 K for 30 minutes, resulting in a total fluence of 1 . 9 × 10 17 ions/m 2 , equivalent to 21 mdpa (as detailed in Appendix B).”
    Quote in the paperSubstantial claim
    • Rests on an assumption: The sample temperature during irradiation is 30 K, or the measured temperature is representative of the irradiated region.

  • May combine two claims.

    Findingown data
    § Appendix A.2. Validation experiment · p. 16

    Both curve conditions exhibit similar cooldown rates, reaching a base temperature of 24 ± 1 K.

    “As shown in Figure A1a, both curve conditions exhibit similar cooldown rates, reaching a base temperature of 24 ± 1 K.”
    Quote in the paperSubstantial claim

  • May combine two claims.

    Findingown data
    § 3.2. Elastic property evolution · p. 11

    Initially, the SAW speed is 2155 ± 7.2 m/s and remains relatively constant until reaching a fluence of 0.6×10^17 ions/m2.

    “Initially, the SAW speed is 2155 ± 7 . 2 m/s and remains relatively constant until reaching a fluence of 0 . 6 × 10 17 ions/m 2 .”
    Quote in the paperNot a substantial claim

  • May combine two claims.

    Findingown data
    § 3.1. Thermal property evolution · p. 9

    As ion fluence increases, the measured thermal diffusivity of Cu-110 at 30 K decays, nearly halving at 1.35 × 10^17 ions/m^2 and plateauing afterwards at 0.7 ± 0.22 × 10^-4 m^2/s.

    “As ion fluence increases, the measured diffusivity decays-nearly halving at 1 . 35 × 10 17 ions / m 2 and plateauing afterwards at 0 . 7 ± 0 . 22 × 10 -4 m 2 / s.”
    Quote in the paperSubstantial claim
    • Rests on an assumption: The sample temperature during irradiation is 30 K, or the measured temperature is representative of the irradiated region.

  • May combine two claims.

    Findingreasoning
    § Appendix A.1. Analytical calculation · p. 14

    The heat load components were Q_cd = 0.354 W, Q_rd = 8.656 W, and Q_H = 9.02 W.

    “Plugging back into the heat load expressions, it was determined that Q cd = 0 . 354 W, Q rd = 8 . 656 W, and Q H = 9 . 02 W.”
    Quote in the paperSubstantial claim
    • The authors state this as an assumption: The TGS and ion beams are perfectly absorbed by the target holder.
    • The authors state this as an assumption: The convective heat load is negligible because the system is in high vacuum.
    • The authors state this as an assumption: Black-body radiation from the vacuum chamber interior walls is the driving radiative load.
    • The authors state this as an assumption: The cylindrical vacuum chamber can be approximated as a sphere with an equivalent diameter.

  • May combine two claims.

    Findingown data
    § 4. Conclusions · p. 12

    We have built and tested a cryogenic target holder where the evolution of fusion magnet materials under irradiation can be assessed via non-contact measurements of thermal diffusivity and SAW speed.

    “We have built and tested a cryogenic target holder where the evolution of fusion magnet materials under irradiation can be assessed via non-contact measurements of thermal diffusivity and SAW speed.”
    Quote in the paperSubstantial claim

  • May combine two claims.

    Findingreasoning
    § Appendix B. Irradiation damage calculation · p. 17

    During the irradiation experiment, the average beam current was 0.45 nA, making the final fluence 1.9×10^17 ions/m2.

    “During the irradiation experiment, the average beam current was 0.45 nA, making the final fluence 1 . 9 × 10 17 ions / m 2 .”
    Quote in the paperNot a substantial claim

  • May combine two claims.

    Findingown data
    § Appendix A.1. Analytical calculation · p. 14

    The dominant heat load is radiative while contributions from conduction, the TGS beam, and the ion beam are comparatively negligible.

    “Here, it becomes evident that the dominant heat load is radiative while contributions from conduction, the TGS beam, and the ion beam are comparatively negligible.”
    Quote in the paperNot a substantial claim
    • The authors state this as an assumption: The TGS and ion beams are perfectly absorbed by the target holder.
    • The authors state this as an assumption: The convective heat load is negligible because the system is in high vacuum.
    • The authors state this as an assumption: Black-body radiation from the vacuum chamber interior walls is the driving radiative load.
    • The authors state this as an assumption: The cylindrical vacuum chamber can be approximated as a sphere with an equivalent diameter.

  • May combine two claims.

    Interpretationcitation
    § 1. Introduction · p. 2

    Developing cryogenic TGS with simultaneous irradiation enables coupled analysis of material evolution under fusion magnet operating conditions, specifically temperatures less than 30 K and irradiation doses greater than 4 mdpa.

    “First, it enables the coupled analysis of material evolution under fusion magnet operating conditions, specifically temperatures less than 30 K [22] and irradiation doses greater than 4 millidisplacements per atom (mdpa).”
    Quote in the paperSubstantial claim0 of 1 sources checked
    • cites [22] [22] R Mumgaard, D Whyte, M Greenwald, Z Hartwig, D Brunner, B Sorbom, E Marmar, J Minervini, P Bonoli, J Irby, B Labombard, J Terry, R Vieira, and S Wukitch. The High Field Path to Practical Fusion Energy. In APS Division of Plasma Physics Meeting Abstracts , volume 2017 of APS Meeting Abstracts , page JP11.081, 2017. -

      Not checked in the free run.

  • May combine two claims.

    Study design and conductnone given
    § 2.2. Cryogenic target holder · p. 7

    The system achieves a base temperature of 30 K with a cooldown time of 3 hours from room temperature.

    “The system achieves a base temperature of 30 K with a cooldown time of 3 hours from room temperature.”
    Quote in the paperNot a substantial claim

  • May combine two claims.

    Premisecitation
    § 1. Introduction · p. 3

    Copper cryo-stability is not guaranteed under irradiation, and copper alloys have demonstrated severe thermal diffusivity degradation and embrittlement post-cryogenic irradiation.

    “But these notions of copper cryo-stability are not guaranteed under the effects of irradiation, and copper alloys have demonstrated severe thermal diffusivity degradation and embrittlement post-cryogenic irradiation [27].”
    Quote in the paperSubstantial claim0 of 1 sources checked
    • cites [27] [27] SA Fabritsiev, AS Pokrovsky, SJ Zinkle, and DJ Edwards. Low-temperature radiation embrittlement of copper alloys. Journal of Nuclear Materials , 233237(Part 1):513-518, 1996. - source

  • May combine two claims.

    Study design and conductnone given
    § Abstract. · p. 1

    The facility combines cryogenic transient grating spectroscopy (TGS) with simultaneous ion irradiation, enabling in-situ measurements of thermal diffusivity and surface acoustic wave (SAW) frequency spectra.

    “Presented here is a facility that combines cryogenic transient grating spectroscopy (TGS) with simultaneous ion irradiation, enabling in-situ measurements of thermal diffusivity and surface acoustic wave (SAW) frequency spectra.”
    Quote in the paperSubstantial claim

  • Probably not a substantial claim: may not pass S3 (load-bearing). May combine two claims.

    Premisecitation
    § 1. Introduction · p. 3

    Within REBCO tapes, the copper stabilizing layer serves as a quench protection mechanism by dissipating heat and providing an alternative current path during transient events.

    “Within the constituent REBCO tapes, the copper stabilizing layer also serves as a quench protection mechanism by dissipating heat and providing an alternative current path during transient events [26].”
    Quote in the paperNot a substantial claim0 of 1 sources checked
    • cites [26] [26] Y Fu, O Tsukamoto, and M Furuse. Copper stabilization of ybco coated conductor for quench protection. IEEE Transactions on Applied Superconductivity , 13(2):1780-1783, 2003. - source

  • May combine two claims.

    Interpretationreasoning
    § 3.1. Thermal property evolution · p. 9

    The discrepancy between measured pre-irradiation diffusivity and literature values likely reflects that TGS's sensitivity is beneficial for detecting relative changes in diffusivity, whereas its absolute calibration can be influenced by beam-spot alignment, surface impurities, and other systematic effects.

    “This discrepancy likely reflects how TGS's sensitivity is beneficial for detecting relative changes in diffusivity, whereas its absolute calibration can be influenced by beam-spot alignment, surface impurities, and other systematic effects.”
    Quote in the paperNot a substantial claim

  • Classified as probably not a substantial claim.

    Premisenone given
    § 2.3. Cu-110 irradiation case study · p. 8

    Self-ion irradiation was chosen to avoid chemical contamination from extraneous ion implantation.

    “Self-ion irradiation was chosen to avoid chemical contamination from extraneous ion implantation.”
    Quote in the paperSubstantial claim

  • May combine two claims.

    Interpretationown data
    § Appendix A.2. Validation experiment · p. 17

    The MLI result confirms that radiative heat is the driving load and increases the base temperature.

    “confirming the hypothesis that radiative heat is the driving load and increases the base temperature.”
    Quote in the paperSubstantial claim

  • May combine two claims.

    Interpretationown data
    § Appendix A.2. Validation experiment · p. 16

    TGS beam heating marginally impacts the cooldown rate, not affecting the final base temperature, and the ion beam interaction remains thermally stable.

    “These observations suggest that TGS beam heating marginally impacts the cooldown rate, not affecting the final base temperature, and the ion beam interaction remains thermally stable.”
    Quote in the paperSubstantial claim

  • May combine two claims.

    Premisecitation
    § 3.2. Elastic property evolution · p. 12

    At cryogenic temperatures below 50 K, defect migration is minimized, meaning clusters are more stable and rarely recombine.

    “At cryogenic temperatures below 50 K, defect migration is minimized, meaning clusters are more stable and rarely recombine [45, 46].”
    Quote in the paperNot a substantial claim0 of 2 sources checked
    • cites [45] [45] SJ Zinkle. Radiation-induced effects on microstructure. In R.J.M. Konings, editor, Comprehensive Nuclear Materials , volume 1, pages 65-98. Elsevier, Amsterdam, 2012. -

      Couldn’t be matched to a paper in Crossref, so it can’t be checked.

    • cites [46] [46] K Wu, G Liu, P Yu, C Ye, J Shi, and Y Shen. Prediction of hardening effect by irradiation-induced vacancy clusters with dislocation dynamics. International Journal of Plasticity , 149:103160, 2022. - source

  • Probably not a substantial claim: may not pass S3 (load-bearing).

    Study design and conductreasoning
    § 2.2. Cryogenic target holder · p. 7

    During experiments, the chamber is kept under vacuum in the 10^-4 Pa range to minimize convection.

    “During experiments, the chamber is kept under vacuum, in the 10 -4 Pa range to minimize convection.”
    Quote in the paperNot a substantial claim

  • Probably not a substantial claim: may not pass S3 (load-bearing). May combine two claims.

    Premisecitation
    § 3.2. Elastic property evolution · p. 12

    Creation of dislocation loops contributes to radiation hardening, correlating to an increase in material stiffness constants, a decrease in density, and an overall increase in SAW speed.

    “their creation contributes to radiation hardening, correlating to an increase in material stiffness constants, a decrease in density, and an overall increase in SAW speed [47, 38].”
    Quote in the paperNot a substantial claim0 of 2 sources checked
    • cites [47] [47] HShulman and WS Ginell. Nuclear and space radiation effects on materials. Special Publication (SP) NASA-SP-8053, NASA, Washington, D.C., 1970. -

      Couldn’t be matched to a paper in Crossref, so it can’t be checked.

    • cites [38] [38] G. S. Was. Fundamentals of Radiation Materials Science , chapter 12, pages 594597. Springer New York, NY, 2 edition, 2017. -

      Couldn’t be matched to a paper in Crossref, so it can’t be checked.

  • Probably not a substantial claim: may not pass S3 (load-bearing). May combine two claims.

    Premisenone given
    § 2.3. Cu-110 irradiation case study · p. 9

    The theoretical TGS probe region extends indefinitely, but signal contributions decrease by a factor of e at 1.12 μm.

    “While the theoretical probe region extends indefinitely, signal contributions decrease by a factor of e at this depth.”
    Quote in the paperNot a substantial claim

  • Probably not a substantial claim: may not pass S3 (load-bearing). May combine two claims.

    Study design and conductnone given
    § 2.1. Transient grating spectroscopy (TGS · p. 5

    The final signal used for fitting was averaged over 10,000 pulses, and a no-pump baseline reading was subtracted to minimize inherent system noise.

    “The final signal used for fitting was averaged over 10,000 pulses, and a no-pump baseline reading was subtracted to minimize inherent system noise.”
    Quote in the paperNot a substantial claim

  • May combine two claims.

    Interpretationreasoning
    § Appendix A.2. Validation experiment · p. 16

    The discrepancy between analytical calculation and experiment is likely due to the use of steel's emissivity at room temperature, which overestimates radiative heat transfer at cryogenic temperatures, and the assumption of perfect absorptivity for the target holder.

    “This discrepancy is likely due to the use of steel's emissivity at room temperature, which overestimates the radiative heat transfer at cryogenic temperatures where metal emissivity typically decreases, as well as the assumption of perfect absorptivity for the target holder, further inflating Q rd and the overall heat load.”
    Quote in the paperNot a substantial claim
    • The authors state this as an assumption: The TGS and ion beams are perfectly absorbed by the target holder.

  • Probably not a substantial claim: may not pass S3 (load-bearing).

    Interpretationcitation
    § 3.1. Thermal property evolution · p. 9

    The observed decrease in thermal diffusivity is possibly caused by stacking fault tetrahedra (SFT) defects, as suggested by previous room temperature, low dose irradiations.

    “The observed decrease in thermal diffusivity is possibly caused by stacking fault tetrahedra (SFT) defects, as suggested by previous room temperature, low dose irradiations [38, 39].”
    Quote in the paperNot a substantial claim0 of 2 sources checked
    • cites [38] [38] G. S. Was. Fundamentals of Radiation Materials Science , chapter 12, pages 594597. Springer New York, NY, 2 edition, 2017. -

      Couldn’t be matched to a paper in Crossref, so it can’t be checked.

    • cites [39] [39] N Li, K Hattar, and A Misra. In situ probing of the evolution of irradiation-induced defects in copper. Journal of Nuclear Materials , 439(1-3):185-191, 2013. - source
    • Rests on an assumption: The sample temperature during irradiation is 30 K, or the measured temperature is representative of the irradiated region.

  • May combine two claims.

    Premisecitation
    § 3.1. Thermal property evolution · p. 9

    Electrical conductivity and thermal conductivity are interrelated by the Wiedemann-Franz Law, which holds for defected copper.

    “Since electrical conductivity and thermal conductivity, κ , are interrelated by the Wiedemann-Franz Law, which holds for defected copper [41]”
    Quote in the paperSubstantial claim0 of 1 sources checked
    • cites [41] [41] XB Ye, ZH He, and BC Pan. The thermal conductivity of defected copper at finite temperatures. Journal of Materials Science , 55(10):4453-4463, 2020. - source

  • May combine two claims.

    Interpretationreasoning
    § 3.1. Thermal property evolution · p. 10

    The number of usable peaks for thermal fitting is significantly reduced in copper, an effect more pronounced at cryogenic temperatures where the TGS signal decays faster.

    “Consequently, the number of usable 'peaks' for thermal fitting is significantly reduced, an effect that is even more pronounced at cryogenic temperatures, where the TGS signal decays faster.”
    Quote in the paperSubstantial claim

  • Probably not a substantial claim: may not pass S3 (load-bearing).

    Study design and conductnone given
    § 3.1. Thermal property evolution · p. 10

    Outliers were removed using a chi-square test with a 95% confidence interval.

    “Outliers were removed using a chi-square test with a 95% confidence interval.”
    Quote in the paperNot a substantial claim

  • Probably not a substantial claim: may not pass S3 (load-bearing).

    Study design and conductnone given
    § 2.3. Cu-110 irradiation case study · p. 8

    A beam profile monitor and quadrupole magnet system maintain a Gaussian profile broadened over a 2 mm aperture to produce a spatially uniform beam spot on the sample.

    “Upstream from the accelerator beamline, a beam profile monitor and quadrupole magnet system are used to maintain a Gaussian profile broadened over a 2 mm aperture to produce a spatially uniform beam spot on the sample.”
    Quote in the paperNot a substantial claim

  • Probably not a substantial claim: may not pass S3 (load-bearing).

    Interpretationreasoning
    § 3.1. Thermal property evolution · p. 9

    TGS could be used as a non-contact method for resistivity recovery experiments.

    “This raises the possibility of using TGS as a non-contact method for resistivity recovery experiments, which has been one of the workhorses of radiation material science [42].”
    Quote in the paperNot a substantial claim0 of 1 sources checked
    • cites [42] [42] B G´ omez-Ferrer. Resistivity Recovery in Fe and FeCr Alloys . Springer Briefs in Applied Sciences and Technology, Berlin, Germany, 2016. -

      Couldn’t be matched to a paper in Crossref, so it can’t be checked.

40 of 40

  • The paper relies on this without support.

    TGS has never been used at cryogenic temperatures with simultaneous irradiation.

    “However, to our knowledge, TGS has never been used at cryogenic temperatures with simultaneous irradiation.”

  • The paper relies on this without support.

    The sample temperature during irradiation is 30 K, or the measured temperature is representative of the irradiated region.

    “Irradiation commenced alongside TGS at 30 K for 30 minutes”

  • The paper relies on this without support.

    In metals and alloys like Cu-110, irradiation-induced lattice vacancies and interstitials form defect clusters within the microstructure.

    “In metals and alloys like Cu-110, irradiation-induced lattice vacancies and interstitials form defect clusters within the microstructure.”

  • The paper relies on this without support.

    A high cluster density impedes the motion and slip of dislocations within the crystal lattice.

    “A high cluster density impedes the motion and slip of dislocations within the crystal lattice.”

  • The authors state this as an assumption.

    The TGS and ion beams are perfectly absorbed by the target holder.

    “The heat loads of the TGS, Q tgs , and ion beam, Q ion , are characterized based on their respective experimental parameters, with the assumption of perfect absorption.”

  • The authors state this as an assumption.

    The convective heat load is negligible because the system is in high vacuum.

    “For Q cv , the load is assumed to be negligible since the system is in high vacuum on the order of 10 -4 Pa,”

  • The authors state this as an assumption.

    Black-body radiation from the vacuum chamber interior walls is the driving radiative load.

    “For Q rd , black-body radiation from the vacuum chamber interior walls is assumed to be driving and the Stefan-Boltzmann law is applied.”

  • The authors state this as an assumption.

    The cylindrical vacuum chamber can be approximated as a sphere with an equivalent diameter.

    “The cylindrical vacuum chamber is approximated as a sphere with an equivalent diameter and the emissivity of 316LN stainless steel at room temperature ( ϵ = 0 . 16) is used,”
8 of 8

Cites

Flagged first, then by citations

3 of the 50 references couldn’t be matched to a known paper.

Research works printed but not linked: 1

  1. [38][38] G. S. Was. Fundamentals of Radiation Materials Science , chapter 12, pages 594597. Springer New York, NY, 2 edition, 2017. -

Cited by

Sorted by citations

Authors
Aurora, A., Devitre, A. R., Wylie, A. P., Rajagopal, J. A., & Short, M. P.
ORCID
Venue
arXiv
Publisher
arXiv
Published
2025
ISSN
2331-8422 (ISSN-L)
DOI
10.48550/arxiv.2506.17358
arXiv
2506.17358
OpenAlex
W6929511349
Semantic Scholar
d475e1dd1c7a8467a03936f637d346364802d89e
Cited by
0
References
50
Type
posted content
Language
en
Open access
Licence
Locations
arXiv (Cornell University) (cc-by)
Topics
  • Physical Sciences › Materials Science › Materials Chemistry › Fusion materials and technologies
  • Physical Sciences › Engineering › Biomedical Engineering › Superconducting Materials and Applications
  • Physical Sciences › Materials Science › Materials Chemistry › Nuclear materials and radiation effects
Keywords
fusion magnets, transient grating spectroscopy, thermal diffusivity, surface acoustic waves, copper, radiation damage, thermomechanical properties, in situ measurement

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Claims read by deepseek-v4.1-flash under definition version 3 (extract-v3) on 2026-10-23.

Classified by jev-1.13-20260917 (gold-guideline-v0.2) on 2026-10-23.

Cited sources are checked by gpt-6-sol.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review