The DOI matches its Crossref record; 236 of the 236 references it cites were found in a registry or an index.
Laser powder bed fusion: a state-of-the-art review of the technology, materials, properties & defects, and numerical modelling
Open accessAbstract
Additive Manufacturing (AM) has revolutionized the manufacturing industry in several directions. Laser powder bed fusion (LPBF), a powder bed fusion AM process, has been dramatically accepted in various industries due to its versatility with several materials, including alloys. This comprehensive review article primarily explains the basic principle of the LPBF process, scientific and technological progress of several inter-related parameters, feedstock materials, produced properties/defects, and insights of numerical modelling to virtually understand the process behavior. Specific attention has been given to selective laser-meted (LPBFed) properties, driven through the microstructure formations and, thereby, concerning defects. The scope of the post-processing techniques to refine microstructure has also been discussed in this review paper. It has been identified that the defects are vital in LPBF process and are primarily governed by the process parameters. Therefore, a wisely chosen, optimized set of parameters can play a crucial role in minimizing defects considerably. Finally, the numerical modeling discussed in this review paper will help the researchers understand the LPBF process.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Additive manufacturing of metallic components – Process, structure and properties
DebRoy, T., Wei, H. L., Zuback, J. S., Mukherjee, T., Elmer, J. W., Milewski, J. O., Beese, A. M., Wilson-Heid, A., De, A., & Zhang, W. (2018) · Progress in Materials Science · doi:10.1016/j.pmatsci.2017.10.001 · Cited by 8,805
Friction stir welding and processing
Mishra, R. S., & Ma, Z. Y. (2005) · Materials Science and Engineering: R: Reports · doi:10.1016/j.mser.2005.07.001 · Cited by 6,753
Metal Additive Manufacturing: A Review
Frazier, W. E. (2014) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-014-0958-z · Cited by 5,984
Ti based biomaterials, the ultimate choice for orthopaedic implants – A review
Geetha, M., Singh, A. K., Asokamani, R., & Gogia, A. K. (2009) · Progress in Materials Science · doi:10.1016/j.pmatsci.2008.06.004 · Cited by 5,416
Additive manufacturing of metals
Herzog, D., Seyda, V., Wycisk, E., & Emmelmann, C. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.07.019 · Cited by 4,759
Mordike, B. L., & Ebert, T. (2001) · Materials Science and Engineering: A · doi:10.1016/s0921-5093(00)01351-4 · Cited by 4,537
Surface modification of titanium, titanium alloys, and related materials for biomedical applications
LIU, X., CHU, P., & DING, C. (2004) · Materials Science and Engineering: R: Reports · doi:10.1016/j.mser.2004.11.001 · Cited by 3,487
Laser additive manufacturing of metallic components: materials, processes and mechanisms
Gu, D. D., Meiners, W., Wissenbach, K., & Poprawe, R. (2012) · International Materials Reviews · doi:10.1179/1743280411y.0000000014 · Cited by 3,197
A study of the microstructural evolution during selective laser melting of Ti–6Al–4V
Thijs, L., Verhaeghe, F., Craeghs, T., Humbeeck, J. V., & Kruth, J.-P. (2010) · Acta Materialia · doi:10.1016/j.actamat.2010.02.004 · Cited by 2,929
The metallurgy and processing science of metal additive manufacturing
Sames, W. J., List, F. A., Pannala, S., Dehoff, R. R., & Babu, S. S. (2016) · International Materials Reviews · doi:10.1080/09506608.2015.1116649 · Cited by 2,529
German, R. M. (1996) · CERN Document Server (European Organization for Nuclear Research) · Cited by 2,502
Corrosion Mechanisms of Magnesium Alloys
Song, G. L., & Atrens, A. (1999) · Advanced Engineering Materials · doi:10.1002/(sici)1527-2648(199909)1:1<11::aid-adem11>3.0.co;2-n · Cited by 2,365
Review of selective laser melting: Materials and applications
Yap, C. Y., Chua, C. K., Dong, Z. L., Liu, Z. H., Zhang, D. Q., Loh, L. E., & Sing, S. L. (2015) · Applied Physics Reviews · doi:10.1063/1.4935926 · Cited by 2,353
Williams, J. C., & Starke, E. A. (2003) · Acta Materialia · doi:10.1016/j.actamat.2003.08.023 · Cited by 2,342
Additive manufacturing: scientific and technological challenges, market uptake and opportunities
Tofail, S. A. M., Koumoulos, E. P., Bandyopadhyay, A., Bose, S., O’Donoghue, L., & Charitidis, C. (2018) · Materials Today · doi:10.1016/j.mattod.2017.07.001 · Cited by 2,136
Additive manufacturing: technology, applications and research needs
Guo, N., & Leu, M. C. (2013) · Frontiers of Mechanical Engineering · doi:10.1007/s11465-013-0248-8 · Cited by 2,073
Design for Additive Manufacturing: Trends, opportunities, considerations, and constraints
Thompson, M. K., Moroni, G., Vaneker, T., Fadel, G., Campbell, R. I., Gibson, I., Bernard, A., Schulz, J., Graf, P., Ahuja, B., et al. (2016) · CIRP Annals · doi:10.1016/j.cirp.2016.05.004 · Cited by 2,017
Residual stresses in selective laser sintering and selective laser melting
Mercelis, P., & Kruth, J. (2006) · Rapid Prototyping Journal · doi:10.1108/13552540610707013 · Cited by 2,015
Thijs, L., Kempen, K., Kruth, J.-P., & Van Humbeeck, J. (2013) · Acta Materialia · doi:10.1016/j.actamat.2012.11.052 · Cited by 1,917
Vrancken, B., Thijs, L., Kruth, J.-P., & Van Humbeeck, J. (2012) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2012.07.022 · Cited by 1,896
The rise of 3-D printing: The advantages of additive manufacturing over traditional manufacturing
Attaran, M. (2017) · Business Horizons · doi:10.1016/j.bushor.2017.05.011 · Cited by 1,822
Olakanmi, E. O., Cochrane, R. F., & Dalgarno, K. W. (2015) · Progress in Materials Science · doi:10.1016/j.pmatsci.2015.03.002 · Cited by 1,742
Microstructural and mechanical characteristics of in situ metal matrix composites
Tjong, S. (2000) · Materials Science and Engineering: R: Reports · doi:10.1016/s0927-796x(00)00024-3 · Cited by 1,722
Observation of keyhole-mode laser melting in laser powder-bed fusion additive manufacturing
King, W. E., Barth, H. D., Castillo, V. M., Gallegos, G. F., Gibbs, J. W., Hahn, D. E., Kamath, C., & Rubenchik, A. M. (2014) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2014.06.005 · Cited by 1,616
Aboulkhair, N. T., Simonelli, M., Parry, L., Ashcroft, I., Tuck, C., & Hague, R. (2019) · Progress in Materials Science · doi:10.1016/j.pmatsci.2019.100578 · Cited by 1,552
Selective laser melting of iron-based powder
Kruth, J. P., Froyen, L., Van Vaerenbergh, J., Mercelis, P., Rombouts, M., & Lauwers, B. (2004) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2003.11.051 · Cited by 1,550
Leuders, S., Thöne, M., Riemer, A., Niendorf, T., Tröster, T., Richard, H. A., & Maier, H. J. (2013) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2012.11.011 · Cited by 1,475
Influence of processing on microstructure and mechanical properties of (α+β) titanium alloys
Lütjering, G. (1998) · Materials Science and Engineering: A · doi:10.1016/s0921-5093(97)00778-8 · Cited by 1,461
Kok, Y., Tan, X. P., Wang, P., Nai, M. L. S., Loh, N. H., Liu, E., & Tor, S. B. (2018) · Materials & Design · doi:10.1016/j.matdes.2017.11.021 · Cited by 1,447
Consolidation phenomena in laser and powder-bed based layered manufacturing
Kruth, J.-P., Levy, G., Klocke, F., & Childs, T. H. C. (2007) · CIRP Annals · doi:10.1016/j.cirp.2007.10.004 · Cited by 1,444
Additive manufacturing methods and modelling approaches: a critical review
Bikas, H., Stavropoulos, P., & Chryssolouris, G. (2016) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-015-7576-2 · Cited by 1,427
Binding mechanisms in selective laser sintering and selective laser melting
Kruth, J., Mercelis, P., Van Vaerenbergh, J., Froyen, L., & Rombouts, M. (2005) · Rapid Prototyping Journal · doi:10.1108/13552540510573365 · Cited by 1,383
Vilaro, T., Colin, C., & Bartout, J. D. (2011) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-011-0731-y · Cited by 1,283
Reducing porosity in AlSi10Mg parts processed by selective laser melting
Aboulkhair, N. T., Everitt, N. M., Ashcroft, I., & Tuck, C. (2014) · Additive Manufacturing · doi:10.1016/j.addma.2014.08.001 · Cited by 1,281
King, W. E., Anderson, A. T., Ferencz, R. M., Hodge, N. E., Kamath, C., Khairallah, S. A., & Rubenchik, A. M. (2015) · Applied Physics Reviews · doi:10.1063/1.4937809 · Cited by 1,258
Xu, W., Brandt, M., Sun, S., Elambasseril, J., Liu, Q., Latham, K., Xia, K., & Qian, M. (2015) · Acta Materialia · doi:10.1016/j.actamat.2014.11.028 · Cited by 1,245
Phase transformations during cooling in α+β titanium alloys
Ahmed, T., & Rack, H. J. (1998) · Materials Science and Engineering A · doi:10.1016/s0921-5093(97)00802-2 · Cited by 1,224
Read, N., Wang, W., Essa, K., & Attallah, M. M. (2015) · Materials & Design (1980-2015) · doi:10.1016/j.matdes.2014.09.044 · Cited by 1,218
Zhang, J., Song, B., Wei, Q., Bourell, D., & Shi, Y. (2019) · Journal of Materials Science & Technology · doi:10.1016/j.jmst.2018.09.004 · Cited by 1,205
Brandl, E., Heckenberger, U., Holzinger, V., & Buchbinder, D. (2012) · Materials & Design · doi:10.1016/j.matdes.2011.07.067 · Cited by 1,151
Shamsaei, N., Yadollahi, A., Bian, L., & Thompson, S. M. (2015) · Additive Manufacturing · doi:10.1016/j.addma.2015.07.002 · Cited by 1,108
Gu, D., Hagedorn, Y.-C., Meiners, W., Meng, G., Batista, R. J. S., Wissenbach, K., & Poprawe, R. (2012) · Acta Materialia · doi:10.1016/j.actamat.2012.04.006 · Cited by 1,089
Qiu, C., Panwisawas, C., Ward, R., Basoalto, H., Brooks, J. W., & Attallah, M. M. (2015) · Acta Materialia · doi:10.1016/j.actamat.2015.06.004 · Cited by 1,041
Effect of the build orientation on the mechanical properties and fracture modes of SLM Ti–6Al–4V
Simonelli, M., Tse, Y. Y., & Tuck, C. (2014) · Materials Science and Engineering: A · doi:10.1016/j.msea.2014.07.086 · Cited by 1,010
Murr, L. E., Quinones, S. A., Gaytan, S. M., Lopez, M. I., Rodela, A., Martinez, E. Y., Hernandez, D. H., Martinez, E., Medina, F., & Wicker, R. B. (2009) · Journal of the Mechanical Behavior of Biomedical Materials · doi:10.1016/j.jmbbm.2008.05.004 · Cited by 997
Agarwal, S., Curtin, J., Duffy, B., & Jaiswal, S. (2016) · Materials Science and Engineering: C · doi:10.1016/j.msec.2016.06.020 · Cited by 955
Sing, S. L., An, J., Yeong, W. Y., & Wiria, F. E. (2016) · Journal of Orthopaedic Research · doi:10.1002/jor.23075 · Cited by 942
Selective laser melting of aluminium components
Louvis, E., Fox, P., & Sutcliffe, C. J. (2011) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2010.09.019 · Cited by 933
Jia, Q., & Gu, D. (2014) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2013.09.171 · Cited by 905
Fatigue performance evaluation of selective laser melted Ti–6Al–4V
Edwards, P., & Ramulu, M. (2014) · Materials Science and Engineering: A · doi:10.1016/j.msea.2014.01.041 · Cited by 874
Al-Bermani, S. S., Blackmore, M., Zhang, W., & Todd, I. (2010) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-010-0397-x · Cited by 860
Single track formation in selective laser melting of metal powders
Yadroitsev, I., Gusarov, A., Yadroitsava, I., & Smurov, I. (2010) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2010.05.010 · Cited by 827
Li, Y., & Gu, D. (2014) · Materials & Design (1980-2015) · doi:10.1016/j.matdes.2014.07.006 · Cited by 824
Gokuldoss, P. K., Kolla, S., & Eckert, J. (2017) · Materials · doi:10.3390/ma10060672 · Cited by 804
Prashanth, K. G., Scudino, S., Klauss, H. J., Surreddi, K. B., Löber, L., Wang, Z., Chaubey, A. K., Kühn, U., & Eckert, J. (2014) · Materials Science and Engineering: A · doi:10.1016/j.msea.2013.10.023 · Cited by 803
On the limitations of Volumetric Energy Density as a design parameter for Selective Laser Melting
Scipioni Bertoli, U., Wolfer, A. J., Matthews, M. J., Delplanque, J.-P. R., & Schoenung, J. M. (2017) · Materials & Design · doi:10.1016/j.matdes.2016.10.037 · Cited by 796
Cherry, J. A., Davies, H. M., Mehmood, S., Lavery, N. P., Brown, S. G. R., & Sienz, J. (2015) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-014-6297-2 · Cited by 755
Manufacture by selective laser melting and mechanical behavior of commercially pure titanium
Attar, H., Calin, M., Zhang, L. C., Scudino, S., & Eckert, J. (2014) · Materials Science and Engineering: A · doi:10.1016/j.msea.2013.11.038 · Cited by 744
Parry, L., Ashcroft, I. A., & Wildman, R. D. (2016) · Additive Manufacturing · doi:10.1016/j.addma.2016.05.014 · Cited by 739
Improvement of fatigue resistance and ductility of TiAl6V4 processed by selective laser melting
Kasperovich, G., & Hausmann, J. (2015) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2015.01.025 · Cited by 735
Balling behavior of stainless steel and nickel powder during selective laser melting process
Li, R., Liu, J., Shi, Y., Wang, L., & Jiang, W. (2012) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-011-3566-1 · Cited by 722
Zhang, L., & Attar, H. (2016) · Advanced Engineering Materials · doi:10.1002/adem.201500419 · Cited by 721
Hussein, A., Hao, L., Yan, C., & Everson, R. (2013) · Materials & Design (1980-2015) · doi:10.1016/j.matdes.2013.05.070 · Cited by 706
Xu, W., Lui, E. W., Pateras, A., Qian, M., & Brandt, M. (2017) · Acta Materialia · doi:10.1016/j.actamat.2016.12.027 · Cited by 687
Zhao, X., Li, S., Zhang, M., Liu, Y., Sercombe, T. B., Wang, S., Hao, Y., Yang, R., & Murr, L. E. (2016) · Materials & Design · doi:10.1016/j.matdes.2015.12.135 · Cited by 673
Thijs, L., Montero Sistiaga, M. L., Wauthle, R., Xie, Q., Kruth, J.-P., & Van Humbeeck, J. (2013) · Acta Materialia · doi:10.1016/j.actamat.2013.04.036 · Cited by 672
Gu, D., & Shen, Y. (2009) · Materials & Design · doi:10.1016/j.matdes.2009.01.013 · Cited by 672
Li, X. P., Wang, X. J., Saunders, M., Suvorova, A., Zhang, L. C., Liu, Y. J., Fang, M. H., Huang, Z. H., & Sercombe, T. B. (2015) · Acta Materialia · doi:10.1016/j.actamat.2015.05.017 · Cited by 654
Beretta, S., & Romano, S. (2017) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2016.06.020 · Cited by 635
Nguyen, H. D., Pramanik, A., Basak, A. K., Dong, Y., Prakash, C., Debnath, S., Shankar, S., Jawahir, I. S., Dixit, S., & Buddhi, D. (2022) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2022.04.055 · Cited by 634
Self-citationOverview of Materials Qualification Needs for Metal Additive Manufacturing
Seifi, M., Salem, A., Beuth, J., Harrysson, O., & Lewandowski, J. J. (2016) · JOM · doi:10.1007/s11837-015-1810-0 · Cited by 630
Spierings, A. B., Herres, N., & Levy, G. (2011) · Rapid Prototyping Journal · doi:10.1108/13552541111124770 · Cited by 614
Comprehensive Materials Processing
(2014) · Elsevier eBooks · doi:10.1016/c2009-1-63473-0 · Cited by 611
A review of laser welding techniques for magnesium alloys
Cao, X. J., Jahazi, M., Immarigeon, J.-P., & Wallace, W. E. (2005) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2005.06.068 · Cited by 610
Manufacture by selective laser melting and mechanical behavior of a biomedical Ti–24Nb–4Zr–8Sn alloy
Zhang, L., Klemm, D., Eckert, J., Hao, Y., & Sercombe, T. B. (2011) · Scripta Materialia · doi:10.1016/j.scriptamat.2011.03.024 · Cited by 597
Residual Stress within Metallic Model Made by Selective Laser Melting Process
Shiomi, M., Osakada, K., Nakamura, K., Yamashita, T., & Abe, F. (2004) · CIRP Annals · doi:10.1016/s0007-8506(07)60677-5 · Cited by 591
Tammas-Williams, S., Zhao, H., Léonard, F., Derguti, F., Todd, I., & Prangnell, P. B. (2015) · Materials Characterization · doi:10.1016/j.matchar.2015.02.008 · Cited by 590
Formation and reduction of hydrogen porosity during selective laser melting of AlSi10Mg
Weingarten, C., Buchbinder, D., Pirch, N., Meiners, W., Wissenbach, K., & Poprawe, R. (2015) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2015.02.013 · Cited by 585
Attar, H., Bönisch, M., Calin, M., Zhang, L.-C., Scudino, S., & Eckert, J. (2014) · Acta Materialia · doi:10.1016/j.actamat.2014.05.022 · Cited by 585
Liu, Y. J., Li, S. J., Wang, H. L., Hou, W. T., Hao, Y. L., Yang, R., Sercombe, T. B., & Zhang, L. C. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.04.029 · Cited by 584
A study on the residual stress during selective laser melting (SLM) of metallic powder
Liu, Y., Yang, Y., & Wang, D. (2016) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-016-8466-y · Cited by 573
Direct selective laser sintering of metals
Agarwala, M., Bourell, D., Beaman, J., Marcus, H., & Barlow, J. (1995) · Rapid Prototyping Journal · doi:10.1108/13552549510078113 · Cited by 571
Vrancken, B., Thijs, L., Kruth, J.-P., & Van Humbeeck, J. (2014) · Acta Materialia · doi:10.1016/j.actamat.2014.01.018 · Cited by 553
Characterization of titanium alloy Ti-6Al-4V for chemical, marine and industrial applications
Gurrappa, I. (2003) · Materials Characterization · doi:10.1016/j.matchar.2003.10.006 · Cited by 512
Liu, Y., Yang, Y., Mai, S., Wang, D., & Song, C. (2015) · Materials & Design · doi:10.1016/j.matdes.2015.08.086 · Cited by 498
Oxides, porosity and fatigue performance of AlSi10Mg parts produced by selective laser melting
Ming, T., & Pistorius, P. C. (2016) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2016.06.002 · Cited by 487
The corrosion behaviour of Ti–6Al–4V, Ti–6Al–7Nb and Ti–13Nb–13Zr in protein solutions
Khan, M. A., Williams, R. L., & Williams, D. F. (1999) · Biomaterials · doi:10.1016/s0142-9612(98)00217-8 · Cited by 485
Wauthle, R., Vrancken, B., Beynaerts, B., Jorissen, K., Schrooten, J., Kruth, J.-P., & Van Humbeeck, J. (2015) · Additive Manufacturing · doi:10.1016/j.addma.2014.12.008 · Cited by 463
Modeling of additive manufacturing processes for metals: Challenges and opportunities
Francois, M. M., Sun, A., King, W. E., Henson, N. J., Tourret, D., Bronkhorst, C. A., Carlson, N. N., Newman, C. K., Haut, T., Bakosi, J., et al. (2017) · Current Opinion in Solid State and Materials Science · doi:10.1016/j.cossms.2016.12.001 · Cited by 462
A Critical Review of the Stress Corrosion Cracking (SCC) of Magnesium Alloys
Winzer, N., Atrens, A., Song, G., Ghali, E., Dietzel, W., Kainer, K. U., Hort, N., & Blawert, C. (2005) · Advanced Engineering Materials · doi:10.1002/adem.200500071 · Cited by 451
Processing metallic glasses by selective laser melting
Pauly, S., Löber, L., Petters, R., Stoica, M., Scudino, S., Kühn, U., & Eckert, J. (2013) · Materials Today · doi:10.1016/j.mattod.2013.01.018 · Cited by 446
Maskery, I., Aremu, A. O., Parry, L., Wildman, R. D., Tuck, C. J., & Ashcroft, I. A. (2018) · Materials & Design · doi:10.1016/j.matdes.2018.05.058 · Cited by 441
Physical Aspects of Process Control in Selective Laser Sintering of Metals
Das, S. (2003) · Advanced Engineering Materials · doi:10.1002/adem.200310099 · Cited by 434
Top surface and side roughness of Inconel 625 parts processed using selective laser melting
Mumtaz, K., & Hopkinson, N. (2009) · Rapid Prototyping Journal · doi:10.1108/13552540910943397 · Cited by 429
Song, B., Dong, S., Zhang, B., Liao, H., & Coddet, C. (2012) · Materials & Design · doi:10.1016/j.matdes.2011.09.051 · Cited by 429
Kobryn, P. A., Moore, E. H., & Semiatin, S. L. (2000) · Scripta Materialia · doi:10.1016/s1359-6462(00)00408-5 · Cited by 428
Microstructure and mechanical behaviour of Ti―6Al―7Nb alloy produced by selective laser melting
Chlebus, E., Kuźnicka, B., Kurzynowski, T., & Dybała, B. (2011) · Materials Characterization · doi:10.1016/j.matchar.2011.03.006 · Cited by 423
Olakanmi, E. O. (2013) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2013.03.009 · Cited by 418
Is the energy density a reliable parameter for materials synthesis by selective laser melting?
Prashanth, K. G., Scudino, S., Maity, T., Das, J., & Eckert, J. (2017) · Materials Research Letters · doi:10.1080/21663831.2017.1299808 · Cited by 418
Solid-state additive manufacturing and repairing by cold spraying: A review
Li, W., Yang, K., Yin, S., Yang, X., Xu, Y., & Lupoi, R. (2017) · Journal of Material Science and Technology · doi:10.1016/j.jmst.2017.09.015 · Cited by 414
Loh, L.-E., Chua, C.-K., Yeong, W.-Y., Song, J., Mapar, M., Sing, S.-L., Liu, Z.-H., & Zhang, D.-Q. (2015) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2014.09.014 · Cited by 408
de Formanoir, C., Michotte, S., Rigo, O., Germain, L., & Godet, S. (2015) · Materials Science and Engineering A · doi:10.1016/j.msea.2015.11.052 · Cited by 404
Balling phenomena in selective laser melted tungsten
Zhou, X., Liu, X., Zhang, D., Shen, Z., & Liu, W. (2015) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2015.02.032 · Cited by 399
Saedi, S., Moghaddam, N. S., Amerinatanzi, A., Elahinia, M., & Karaca, H. E. (2017) · Acta Materialia · doi:10.1016/j.actamat.2017.10.072 · Cited by 391
Pattanayak, D. K., Fukuda, A., Matsushita, T., Takemoto, M., Fujibayashi, S., Sasaki, K., Nishida, N., Nakamura, T., & Kokubo, T. (2011) · Acta Biomaterialia · doi:10.1016/j.actbio.2010.09.034 · Cited by 384
Yasa, E., Deckers, J., & Kruth, J. (2011) · Rapid Prototyping Journal · doi:10.1108/13552541111156450 · Cited by 371
Scime, L., & Beuth, J. (2019) · Additive Manufacturing · doi:10.1016/j.addma.2018.11.010 · Cited by 369
AIAA Propulsion and Energy 2019 Forum
(2019) · doi:10.2514/mpef19 · Cited by 368
Shi, R., Khairallah, S. A., Roehling, T. T., Heo, T. W., McKeown, J. T., & Matthews, M. J. (2020) · Acta Materialia · doi:10.1016/j.actamat.2019.11.053 · Cited by 365
Heat transfer and material flow during laser assisted multi-layer additive manufacturing
Manvatkar, V., De, A., & DebRoy, T. (2014) · Journal of Applied Physics · doi:10.1063/1.4896751 · Cited by 362
Gradient in microstructure and mechanical property of selective laser melted AlSi10Mg
Liu, Y., Liu, Z., Jiang, Y., Wang, G. W., Yang, Y., & Zhang, L. (2017) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2017.11.020 · Cited by 352
Solidification in direct metal deposition by LENS processing
Hofmeister, W., & Griffith, M. (2001) · JOM · doi:10.1007/s11837-001-0066-z · Cited by 351
Surface Morphology in Selective Laser Melting of Metal Powders
Yadroitsev, I., & Smurov, I. (2011) · Physics Procedia · doi:10.1016/j.phpro.2011.03.034 · Cited by 349
Laser Additive Manufacturing of High-Performance Materials
Gu, D. (2015) · Springer eBooks · doi:10.1007/978-3-662-46089-4 · Cited by 349
Yang, J., Han, J. C., Yu, H., Yin, J., Gao, M. X., Wang, Z., & Zeng, X. (2016) · Materials & Design · doi:10.1016/j.matdes.2016.08.036 · Cited by 346
Simonelli, M., Tuck, C., Aboulkhair, N. T., Maskery, I., Ashcroft, I., Wildman, R. D., & Hague, R. (2015) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-015-2882-8 · Cited by 342
Carter, L. N., Attallah, M. M., & Reed, R. C. (2012) · Wiley eBooks · doi:10.1002/9781118516430.ch64 · Cited by 342
A machine-learning fatigue life prediction approach of additively manufactured metals
Bao, H., Wu, S., Wu, Z., Kang, G., Peng, X., & Withers, P. J. (2021) · Engineering Fracture Mechanics · doi:10.1016/j.engfracmech.2020.107508 · Cited by 336
Additive Manufacturing for the Aerospace Industry
(2019) · Elsevier eBooks · doi:10.1016/c2017-0-00712-7 · Cited by 331
Wei, K., Gao, M., Wang, Z., & Zeng, X. (2014) · Materials Science and Engineering: A · doi:10.1016/j.msea.2014.05.092 · Cited by 330
Understanding thermal behavior in the LENS process
Griffith, M. L., Schlienger, M. E., Harwell, L. D., Oliver, M. S., Baldwin, M. D., Ensz, M. T., Essien, M., Brooks, J., Robino, C. V., Smugeresky, J. E., et al. (1999) · Materials & Design · doi:10.1016/s0261-3069(99)00016-3 · Cited by 327
Problems and issues in laser beam welding of aluminum–lithium alloys
Xiao, R., & Zhang, X. (2014) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2013.10.005 · Cited by 325
Liu, Q., Wu, H., Paul, M. J., He, P., Peng, Z., Gludovatz, B., Kruzic, J. J., Wang, C. H., & Li, X. (2020) · Acta Materialia · doi:10.1016/j.actamat.2020.10.010 · Cited by 321
Microstructure and deformation behavior of Ti-6Al-4V alloy by high-power laser solid forming
Ren, Y., Lin, X., Fu, X., Tan, H., Chen, J., & Huang, W. D. (2017) · Acta Materialia · doi:10.1016/j.actamat.2017.04.026 · Cited by 316
Heat transfer modelling and stability analysis of selective laser melting
Gusarov, A. V., Yadroitsev, I., Bertrand, P., & Smurov, I. (2007) · Applied Surface Science · doi:10.1016/j.apsusc.2007.08.074 · Cited by 314
Kaufmann, N., Imran, M., Wischeropp, T. M., et al. (2016) · Physics Procedia · doi:10.1016/j.phpro.2016.08.096 · Cited by 314
Damage evolution and failure mechanisms in additively manufactured stainless steel
Carlton, H. D., Haboub, A., Gallegos, G. F., Parkinson, D. Y., & MacDowell, A. A. (2016) · Materials Science and Engineering: A · doi:10.1016/j.msea.2015.10.073 · Cited by 313
A multiscale modeling approach for fast prediction of part distortion in selective laser melting
Li, C., Fu, C. H., Guo, Y. B., & Fang, F. (2015) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2015.10.022 · Cited by 308
Warnke, P. H., Douglas, T., Wollny, P., Sherry, E., Steiner, M., Galonska, S., Becker, S. T., Springer, I. N., Wiltfang, J., & Sivananthan, S. (2009) · Tissue Engineering Part C: Methods · doi:10.1089/ten.tec.2008.0288 · Cited by 305
Fischer, M., Joguet, D., Robin, G., Peltier, L., & Laheurte, P. (2016) · Materials Science and Engineering C · doi:10.1016/j.msec.2016.02.033 · Cited by 295
Wu, S., Lu, Y., Gan, Y. L., Huang, T., Zhao, C. Q., Lin, J., Guo, S., & Lin, J. (2016) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2016.02.183 · Cited by 292
Effects of processing parameters on properties of selective laser melting Mg–9%Al powder mixture
Zhang, B., Liao, H., & Coddet, C. (2012) · Materials & Design · doi:10.1016/j.matdes.2011.06.061 · Cited by 280
Gu, D., Wang, H., Dai, D., Yuan, P., Meiners, W., & Poprawe, R. (2015) · Scripta Materialia · doi:10.1016/j.scriptamat.2014.10.011 · Cited by 279
The effect of atmosphere on the structure and properties of a selective laser melted Al–12Si alloy
Wang, X. J., Zhang, L., Fang, M., & Sercombe, T. B. (2014) · Materials Science and Engineering A · doi:10.1016/j.msea.2014.01.012 · Cited by 277
Zhang, X.-Y., Fang, G., Leeflang, S., Zadpoor, A. A., & Zhou, J. (2019) · Acta Biomaterialia · doi:10.1016/j.actbio.2018.12.013 · Cited by 277
Robot assisted additive manufacturing: A review
Urhal, P., Weightman, A., Diver, C., & Bartolo, P. (2019) · Robotics and Computer-Integrated Manufacturing · doi:10.1016/j.rcim.2019.05.005 · Cited by 277
Qualification of AM parts: Extreme value statistics applied to tomographic measurements
Romano, S., Brandão, A., Gumpinger, J., Gschweitl, M., & Beretta, S. (2017) · Materials & Design · doi:10.1016/j.matdes.2017.05.091 · Cited by 269
Baumgartl, H., Tomas, J., Buettner, R., & Merkel, M. (2020) · Progress in Additive Manufacturing · doi:10.1007/s40964-019-00108-3 · Cited by 268
Rapid Solidification: Selective Laser Melting of AlSi10Mg
Tang, M., Pistorius, P. C., Narra, S., & Beuth, J. L. (2016) · JOM · doi:10.1007/s11837-015-1763-3 · Cited by 260
AlMangour, B., Grzesiak, D., & Yang, J.-M. (2017) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2017.08.022 · Cited by 259
Numerical modelling of welding
Lindgren, L.-E. (2006) · Computer Methods in Applied Mechanics and Engineering · doi:10.1016/j.cma.2005.08.018 · Cited by 257
Gu, D., Hagedorn, Y.-C., Meiners, W., Wissenbach, K., & Poprawe, R. (2011) · Composites Science and Technology · doi:10.1016/j.compscitech.2011.07.010 · Cited by 256
Zhang, M., Sun, C.-N., Zhang, X., Goh, P. C., Wei, J., Hardacre, D., & Li, H. (2019) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2019.105194 · Cited by 251
A high-strength Mg–Ni–Y alloy sheet with a long-period ordered phase prepared by hot-rolling
Itoi, T., Takahashi, K., Moriyama, H., & Hirohashi, M. (2008) · Scripta Materialia · doi:10.1016/j.scriptamat.2008.08.001 · Cited by 245
Ti-6Al-4V Additively Manufactured by Selective Laser Melting with Superior Mechanical Properties
Xu, W., Sun, S., Elambasseril, J., Liu, Q., Brandt, M., & Qian, M. (2015) · JOM · doi:10.1007/s11837-015-1297-8 · Cited by 244
Selective Laser Melting of Magnesium and Magnesium Alloy Powders: A Review
Manakari, V., Parande, G., & Gupta, M. (2016) · Metals · doi:10.3390/met7010002 · Cited by 241
Hu, Y., Wu, S., Wu, Z., Zhong, X., Ahmed, S., Karabal, S., Xiao, X., Zhang, H. O., & Withers, P. J. (2020) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2020.105584 · Cited by 240
Influence of tempering temperature and time on the α′-Ti-6Al-4V martensite
Gil, F. X., Rius, D. R., & Planell, J. A. (1996) · Journal of Alloys and Compounds · doi:10.1016/0925-8388(95)02057-8 · Cited by 230
Ma, M., Wang, Z., Gao, M. X., & Zeng, X. (2014) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2014.07.034 · Cited by 228
The imaging of failure in structural materials by synchrotron radiation X-ray microtomography
Wu, S. C., Xiao, T. Q., & Withers, P. J. (2017) · Engineering Fracture Mechanics · doi:10.1016/j.engfracmech.2017.07.027 · Cited by 225
A review of technological improvements in laser-based powder bed fusion of metal printers
Khorasani, A., Gibson, I., Veetil, J. K., & Ghasemi, A. H. (2020) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-020-05361-3 · Cited by 225
Microstructure and tensile properties of iron parts fabricated by selective laser melting
Song, B., Dong, S., Deng, S., Liao, H., & Coddet, C. (2014) · Optics & Laser Technology · doi:10.1016/j.optlastec.2013.09.017 · Cited by 219
Automatic fault detection for laser powder-bed fusion using semi-supervised machine learning
Okaro, I. A., Jayasinghe, S., Sutcliffe, C., Black, K., Paoletti, P., & Green, P. L. (2019) · Additive Manufacturing · doi:10.1016/j.addma.2019.01.006 · Cited by 219
Zheng, B., Zhou, Y., Smugeresky, J. E., Schoenung, J. M., & Lavernia, E. J. (2008) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-008-9566-6 · Cited by 214
Microstructure and mechanical properties of selective laser melted magnesium
Ng, C. C., Savalani, M. M., Lau, M. L., & Man, H. C. (2011) · Applied Surface Science · doi:10.1016/j.apsusc.2011.03.004 · Cited by 208
Weld metal composition change during conduction mode laser welding of aluminum alloy 5182
Zhao, H., & Debroy, T. (2001) · Metallurgical and Materials Transactions B · doi:10.1007/s11663-001-0018-6 · Cited by 204
Bulk and porous metastable beta Ti–Nb–Zr(Ta) alloys for biomedical applications
Braïlovski, V., Дмитриевич, П. С., Gauthier, M., Inaekyan, K. E., Dubinskiy, S., Иванович, П. М., & Filonov, M. R. (2011) · Materials Science and Engineering C · doi:10.1016/j.msec.2010.12.008 · Cited by 199
The potency of defects on fatigue of additively manufactured metals
Peng, X., Wu, S., Qian, W., Bao, J., Hu, Y., Zhan, Z., Guo, G., & Withers, P. J. (2022) · International Journal of Mechanical Sciences · doi:10.1016/j.ijmecsci.2022.107185 · Cited by 197
Laser-based powder bed fusion additive manufacturing of pure copper
Jadhav, S. D., Goossens, L. R., Kinds, Y., Hooreweder, B. V., & Vanmeensel, K. (2021) · Additive Manufacturing · doi:10.1016/j.addma.2021.101990 · Cited by 195
Roach, D. J., Hamel, C. M., Dunn, C. K., Johnson, M. V., Kuang, X., & Qi, H. J. (2019) · Additive Manufacturing · doi:10.1016/j.addma.2019.100819 · Cited by 191
Material Reuse in Laser Powder Bed Fusion: Side Effects of the Laser—Metal Powder Interaction
Santecchia, E., Spigarelli, S., & Cabibbo, M. (2020) · Metals · doi:10.3390/met10030341 · Cited by 188
Perspectives of using machine learning in laser powder bed fusion for metal additive manufacturing
Sing, S. L., Kuo, C. N., Shih, C. T., Ho, C. C., & Chua, C. K. (2021) · Virtual and Physical Prototyping · doi:10.1080/17452759.2021.1944229 · Cited by 185
Anisotropic response of Ti-6Al-4V alloy fabricated by 3D printing selective laser melting
Chen, L. Y., Huang, J. C., Lin, C., Pan, C., Chen, S. Y., Yang, T.-J., Lin, D. Y., Lin, H. K., & Jang, J. S. C. (2016) · Materials Science and Engineering A · doi:10.1016/j.msea.2016.11.061 · Cited by 182
Balling phenomena during direct laser sintering of multi-component Cu-based metal powder
Gu, D., & Shen, Y. (2007) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2006.06.011 · Cited by 178
Wear behavior and microstructure of hypereutectic Al-Si alloys prepared by selective laser melting
Kang, N., Coddet, P., Liao, H., Baur, T., & Coddet, C. (2016) · Applied Surface Science · doi:10.1016/j.apsusc.2016.03.221 · Cited by 178
Additive manufacturing for aerospace flight applications
Shapiro, A. A., Borgonia, J. P., Chen, Q. N., Dillon, R. P., McEnerney, B., Polit-Casillas, R., & Soloway, L. (2016) · Journal of Spacecraft and Rockets · doi:10.2514/1.a33544 · Cited by 178
Scime, L., & Beuth, J. (2019) · Additive Manufacturing · doi:10.1016/j.addma.2019.100830 · Cited by 176
Xie, C., Wu, S., Yu, Y., Zhang, H., Hu, Y., Zhang, M., & Wang, G. (2021) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2020.117039 · Cited by 172
Olakanmi, E. O., Cochrane, R. F., & Dalgarno, K. W. (2011) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2010.09.003 · Cited by 171
Thermal Modeling of Electron Beam Additive Manufacturing Process: Powder Sintering Effects
Shen, N., & Chou, K. (2012) · ASME International Manufacturing Science and Engineering Conference (MSEC) · doi:10.1115/msec2012-7253 · Cited by 171
Khoa, D., & Li, P. (2016) · Virtual and Physical Prototyping · doi:10.1080/17452759.2016.1142215 · Cited by 167
Ahmad, B., van der Veen, S. O., Fitzpatrick, M. E., & Guo, H. F. (2018) · Additive manufacturing · doi:10.1016/j.addma.2018.06.002 · Cited by 166
Cao, X., Wallace, W., Immarigeon, J.-P., & Poon, C. (2003) · Materials and Manufacturing Processes · doi:10.1081/amp-120017587 · Cited by 164
Zhang, L., Song, B., Yang, L., & Shi, Y. (2020) · Acta Biomaterialia · doi:10.1016/j.actbio.2020.05.038 · Cited by 164
Dadbakhsh, S., & Hao, L. (2012) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2012.06.097 · Cited by 163
Mechanical properties of a Ti6Al4V porous structure produced by selective laser melting
Sun, J., Yang, Y., & Wang, D. (2013) · Materials & Design (1980-2015) · doi:10.1016/j.matdes.2013.01.038 · Cited by 163
Miyanaji, H., Zhang, S., & Yang, L. (2017) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2017.09.001 · Cited by 160
Johnston, S., Shi, Z., & Atrens, A. (2015) · Corrosion Science · doi:10.1016/j.corsci.2015.09.018 · Cited by 156
Riener, K., Nikolaj, A., Ziegelmeier, S., Ramakrishnan, R., Haferkamp, L., Spierings, A. B., & Leichtfried, G. J. (2020) · Additive manufacturing · doi:10.1016/j.addma.2020.101286 · Cited by 156
The formation of α + β microstructure in as-fabricated selective laser melting of Ti–6Al–4V
Simonelli, M., Tse, Y. Y., & Tuck, C. J. (2014) · Journal of materials research/Pratt's guide to venture capital sources · doi:10.1557/jmr.2014.166 · Cited by 154
Romano, S., Abel, A. M., Gumpinger, J., Brandão, A. D., & Beretta, S. (2019) · Additive manufacturing · doi:10.1016/j.addma.2019.05.017 · Cited by 154
Gaikwad, A., Giera, B., Guss, G. M., Forien, J., Matthews, M. J., & Rao, P. (2020) · Additive manufacturing · doi:10.1016/j.addma.2020.101659 · Cited by 153
Li, X., Kang, C. W., Huang, H., & Sercombe, T. B. (2014) · Materials & Design (1980-2015) · doi:10.1016/j.matdes.2014.06.022 · Cited by 151
Dai, D., & Gu, D. (2015) · Applied Surface Science · doi:10.1016/j.apsusc.2015.07.044 · Cited by 147
Study of the Pore Formation on CoCrMo Alloys by Selective Laser Melting Manufacturing Process
Monroy, K. P., Delgado, J., & Ciurana, J. (2013) · Procedia Engineering · doi:10.1016/j.proeng.2013.08.227 · Cited by 147
Attar, H., Bönisch, M., Calin, M., Zhang, L., Zhuravleva, K., Funk, A., Scudino, S., Yang, C. Q., & Eckert, J. (2014) · Journal of materials research/Pratt's guide to venture capital sources · doi:10.1557/jmr.2014.122 · Cited by 139
Gu, D., & Meiners, W. (2010) · Materials Science and Engineering A · doi:10.1016/j.msea.2010.08.075 · Cited by 136
Muñiz-Lerma, J. A., Nommeots‐Nomm, A., Waters, K. E., & Brochu, M. (2018) · Materials · doi:10.3390/ma11122386 · Cited by 135
Fukuda, A., Takemoto, M., Saito, T., Fujibayashi, S., Neo, M., Yamaguchi, S., Kizuki, T., Matsushita, T., Niinomi, M., Kokubo, T., et al. (2010) · Acta Biomaterialia · doi:10.1016/j.actbio.2010.09.026 · Cited by 134
Casavola, C., Campanelli, S. L., & Pappalettere, C. (2008) · The Journal of Strain Analysis for Engineering Design · doi:10.1243/03093247jsa464 · Cited by 134
Chen, Q., Zhao, Y., Strayer, S. T., Zhao, Y., Aoyagi, K., Koizumi, Y., Chiba, A., Xiong, W., & To, A. C. (2020) · Additive manufacturing · doi:10.1016/j.addma.2020.101642 · Cited by 133
Layer manufacturing of magnesium and its alloy structures for future applications
Ng, C. C., Savalani, M. M., Man, H. C., & Gibson, I. (2010) · Virtual and Physical Prototyping · doi:10.1080/17452751003718629 · Cited by 131
Laser rapid solidification improves corrosion behavior of Mg-Zn-Zr alloy
Shuai, C., Yang, Y., Wu, P., Lin, X., Liu, Y., Zhou, Y., Feng, P., Liu, X., & Peng, S. (2016) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2016.09.019 · Cited by 130
Shi, X., Ma, S., Liu, C., & Wu, Q. (2016) · Optics & Laser Technology · doi:10.1016/j.optlastec.2016.11.002 · Cited by 130
Mechanism of alloying element vaporization during laser welding
Collur, M. M., Paul, A. J., & DebRoy, T. (1987) · Metallurgical Transactions B · doi:10.1007/bf02672891 · Cited by 127
Thermal control of laser powder bed fusion using deep reinforcement learning
Ogoke, F., & Farimani, A. B. (2021) · Additive manufacturing · doi:10.1016/j.addma.2021.102033 · Cited by 124
The effect of the atmosphere and the role of pore filling on the sintering of aluminium
Schaffer, G. B., Hall, B. J., Bonner, S., Huo, S. H., & Sercombe, T. B. (2005) · Acta Materialia · doi:10.1016/j.actamat.2005.08.032 · Cited by 119
Part geometry and conduction-based laser power control for powder bed fusion additive manufacturing
Yeung, H., Lane, B. M., & Fox, J. C. (2019) · Additive manufacturing · doi:10.1016/j.addma.2019.100844 · Cited by 117
Yan, Y., Cao, H., Kang, Y., Yu, K., Xiao, T., Luo, J., Deng, Y., Fang, H., Xiong, H., & Dai, Y. (2016) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2016.10.017 · Cited by 116
Convective heat transfer performance of airfoil heat sinks fabricated by selective laser melting
Ho, J. Y., Wong, K. K., Leong, K. C., & Wong, T. N. (2017) · International Journal of Thermal Sciences · doi:10.1016/j.ijthermalsci.2016.12.016 · Cited by 115
Cited by
Additive manufacturing of heat exchangers in aerospace applications: a review
Careri, F., Khan, R. H. U., Todd, C., & Attallah, M. M. (2023) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2023.121387 · Cited by 320
Cortis, D., Pilone, D., Grazzi, F., Broggiato, G., Campana, F., Orlandi, D., Shinohara, T., & Planell, O. S. (2025) · Progress in Additive Manufacturing · doi:10.1007/s40964-024-00761-3 · Cited by 13
Metadata
- Authors
- Chowdhury, S., Yadaiah, N., Prakash, C., Ramakrishna, S., Dixit, S., Gupta, L. R., & Buddhi, D.
- Venue
- Journal of Materials Research and Technology
- Publisher
- Elsevier BV
- Published
- 2022-09
- Volume
- 20
- Pages
- 2109-2172
- ISSN
- 2214-0697 (ISSN-L)
- 2238-7854
- OpenAlex
- W4292448523
- Cited by
- 784
- References
- 236
- FWCI
- 48.66
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.