Biodegradable synthetic polymers for tissue engineering
Open accessThe DOI matches its Crossref record; 96 of the 97 references it cites were found in a registry or an index; 1 of the 146 sources its claims cite were checked for support.
Abstract
This review focuses on biodegradable synthetic polymers, discussing synthesis, properties and biodegradability, especially within the polyester family including polylactides.
Overview
CoChat Summary
TL;DR
This review surveys biodegradable synthetic polymers for tissue engineering, emphasizing polyesters (PGA, PLA, PLGA), polylactones, poly(propylene fumarate), polyanhydrides, tyrosine-derived polycarbonates, polyorthoesters, polyurethanes, and polyphosphazenes. It concludes that polyesters dominate clinically, while injectable in situ curable systems such as PPF and photocrosslinkable polyanhydrides are promising but face challenges in biocompatibility, degradation control, and heat generation.
Key findings
- Polyesters are the most studied biodegradable polymers. PGA has 46–50% crystallinity, Tg 36°C, Tm 225°C; in Dexon sutures in vitro, first-stage degradation predominates for 21 days, crystalline degradation takes a further 28 days, and after 49 days weight loss was about 42% with complete loss of mechanical properties.
- PLA/PGA copolymer behavior depends on composition: 25–75% (l)LA/GA and 0–70% (dl)LA/GA are amorphous; 70/30 GA/LA has the highest water uptake, while 50/50 is reported as most unstable to hydrolysis; Vicryl is 8% (l)LA and 92% GA.
- Poly(caprolactone) degrades slowly: homopolymer degradation is on the order of 2–3 years, and PCL with initial average molecular weight 50,000 takes about 3 years for complete in vitro degradation.
- Poly(propylene fumarate) degrades to fumaric acid and propylene glycol; time to 20% original weight loss ranged from 84 days (PPF/β-TCP composite) to over 200 days (PPF/CaSO4 composite). PPF formulations showed maximum curing temperatures of 38–48°C versus 94°C for PMMA cements, curing times of 1–121 min, and compressive strengths of 1–12 MPa.
- Polyanhydrides degrade by surface erosion; poly(sebacic acid) degrades in about 54 days in saline, while poly(1,6-bis(p-carboxyphenoxy)hexane) is estimated at 1 year. Poly[1,6-bis(carboxyphenoxy)hexane] has a Young’s modulus of 1.3 MPa versus human bone at 40–60 MPa; poly(anhydride-co-imides) reached compressive strengths of 50–60 MPa, and photocrosslinked systems showed compressive strengths of 30–40 MPa and tensile strengths of 15–27 MPa.
- Degradable polyurethanes based on lysine diisocyanate showed varied properties: dl-lactide networks were rigid (Tg = 60°C) with ultimate tensile strengths of ~40–70 MPa, caprolactone triol networks were low-modulus elastomers with tensile strengths of 1–4 MPa, and copolymer networks had elongation up to 600% with compressive strengths of 3–25 MPa. In vivo, porous polyurethane artificial skin degraded almost completely 4–8 weeks after implantation in guinea pigs with no adverse tissue reaction.
Methods
- Design: narrative literature review; no primary experimental study or systematic review protocol is reported.
- Data/sample: published literature on biodegradable synthetic polymers, including synthesis, properties, degradation, biocompatibility, and injectable polymer systems; Tables 1–3 summarize polymer properties and precursors.
- Analysis: qualitative synthesis of major polymer classes, their degradation modes/products, mechanical properties, biocompatibility, and potential for injectable tissue-engineering compositions.
Limitations
- Stated: the paper notes that Table 2 data “should be used as a guide only” and that sufficient data are not available to provide a comprehensive list of properties for polyanhydrides, polycarbonates, polyurethanes, and polyphosphazenes.
- Stated: for polyanhydrides, no data are reported about polymer sterilizability and heat generation during polymerization; for degradable polyurethanes, the effect of degradation products and how they are removed from the body are not clearly understood.
- Evident: as a narrative review, it lacks systematic search criteria, study quality appraisal, and meta-analysis, so conclusions depend on the cited literature and may not comprehensively cover all biodegradable polymers or tissue-engineering applications.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
1 Valid · 20 Not valid · 105 Not checked · 89 Own results and interpretations
Every source the paper cites for this claim was checked and supports it.
In the paper
“A meniscal replica implanted contained only fibro-cartilage after 18 weeks and decreased the degradation of the articular cartilage.”
What the sources say
- Supportedcites De Groot et al.., 1996 source
The Aliphatic PU network passage (page not provided) reports that articular-cartilage degeneration was less severe with the prosthesis than in meniscectomized control knees. It also says the prostheses contained only fibrocartilage after 18 weeks. Degeneration was reduced, not eliminated. (LLM, conf=0.91)
plainstates a causeSingle case- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
In the paper
“The compressive strengths varied between 1 and 12 MPa”
What the sources say
- Not matchedcites Peter et al., 1998a
Couldn’t be matched to a paper in Crossref, so it can’t be checked.
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Not matched
In the paper
“Cross-linking characteristics reported for PPF, N-vinyl pyrrolidone (N-VP), benzoyl peroxide, sodium chloride, and TCP indicate that for a range of formulations, the maximum temperature varied within 38 to about 48ºC, compared to 94ºC observed for polymethylmethacrylate (PMMA) cements.”
What the sources say
- Not matchedcites Peter et al., 1998a
Couldn’t be matched to a paper in Crossref, so it can’t be checked.
hedged- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Not matched
None of the sources cited for this claim could be matched to a paper in Crossref, so there is nothing to check it against.
In the paper
“Based on in-vitro studies, the time required to reach 20% loss in original weight ranged from 84 (PPF/ß-TCP composite) to over 200 days (PPF/CaSO 4 composite)”
What the sources say
- Not matchedcites Peter et al., 1997b
Couldn’t be matched to a paper in Crossref, so it can’t be checked.
- Not matchedcites Kharas et al., 1997
Couldn’t be matched to a paper in Crossref, so it can’t be checked.
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Not matched
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“These composite materials exhibit compressive strengths in the range 2 to 30 MPa.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
94 more claims
Create a free account to see all 215 claims and to verify the 2 references still open.
- It may state two separate claims as one. 62
- Probably not a substantial claim. 76
- The quote only partly states this claim. 1
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“Advantages include a tightly controlled manufacturing process, accurate reproducibility, adjustable biodegradability, and a wide variety of both chemical and physical properties.[ 171 ]”
From Unraveling and Harnessing the Immune Response at the Cell–Biomaterial Interface for Tissue Engineering Purposes (2024) · cites this paper as [171]
Experimental — accuracy not yet measured
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
§ Polyanhydrides
“Polyanhydrides degrades by surface erosion (Kohn and Langer, 1997) and their main applications are in controlled drug delivery.”
§ Conclusions
“Polyanhydride degrade by bulk erosion and their main applications are in controlled drug delivery.”
Citations
Cites
Synthetic biodegradable polymers as orthopedic devices
Middleton, J. C., & Tipton, A. J. (2000) · Biomaterials · doi:10.1016/s0142-9612(00)00101-0 · Cited by 2,741 · cited 4×
“…developments in siloxane-based polyurethanes, which have greater in-vivo stability than conventional polyetherurethanes (e.g., poly(tetramethylene oxide) (PTMO)-based) have provided opportunities for development of a range of medical implants for chronic applications (Gunatillake et al., 2001).”
BackgroundInfluentialBiomaterial developments for bone tissue engineering
Burg, K. J. L., Porter, S., & Kellam, J. F. (2000) · Biomaterials · doi:10.1016/s0142-9612(00)00102-2 · Cited by 1,643 · cited 1×
“Polyesters have also been considered for development of tissue engineering applications (Hubbell, 1995; Thomson et al 1995a, Yazemski et al. 1996; Wong and Mooney, 1997), particularly for bone tissue engineering (Kohn and Langer, 1997; Burg et al., 2000).”
BackgroundChandra, R. (1998) · Progress in Polymer Science · doi:10.1016/s0079-6700(97)00039-7 · Cited by 1,462
Biodegradable polymers for use in surgery—polyglycolic/poly(actic acid) homo- and copolymers: 1
Gilding, D. K., & Reed, A. M. (1979) · Polymer · doi:10.1016/0032-3861(79)90009-0 · Cited by 1,345
Biomaterials in Tissue Engineering
Hubbell, J. A. (1995) · Nature Biotechnology · doi:10.1038/nbt0695-565 · Cited by 1,060 · cited 1×
“Polyesters have also been considered for development of tissue engineering applications (Hubbell, 1995; Thomson et al 1995a, Yazemski et al. 1996; Wong and Mooney, 1997), particularly for bone tissue engineering (Kohn and Langer, 1997; Burg et al., 2000).”
BackgroundPolylactic Acid for Surgical Implants
KULKARNI, R. K. (1966) · Archives of Surgery · doi:10.1001/archsurg.1966.01330050143023 · Cited by 841
Evolution of bone transplantation: molecular, cellular and tissue strategies to engineer human bone
Yaszemski, M. J., Payne, R. G., Hayes, W. C., Langer, R., & Mikos, A. G. (1996) · Biomaterials · doi:10.1016/0142-9612(96)85762-0 · Cited by 729
Miller, R. A., Brady, J. M., & Cutright, D. E. (1977) · Journal of Biomedical Materials Research · doi:10.1002/jbm.820110507 · Cited by 722 · cited 2×
“For the (l)LA/GA copolymers, resistance to hydrolysis is more pronounced at either end of the copolymers compositions range (Miller et al., 1977; Gilding and Reed, 1979; Reed and Gilding, 1981; Vert et al., 1984).”
BackgroundInjectable biodegradable materials for orthopedic tissue engineering
Temenoff, J. S., & Mikos, A. G. (2000) · Biomaterials · doi:10.1016/s0142-9612(00)00108-3 · Cited by 554 · cited 8×
“A number of methods have been reported to prepare PPF, and each results in different polymer properties (Peter et al., 1997a,b, 1999; Temenoff and Mikos 2000).”
BackgroundMethodInfluentialLeong, K. W., Brott, B. C., & Langer, R. (1985) · Journal of Biomedical Materials Research · doi:10.1002/jbm.820190806 · Cited by 541 · cited 12×
“The polyurethanes ranged from elastomers with elongations at break as high as 780 %, but with low tensile strengths (5.8 to 8.1 MPa).”
BackgroundInfluential
Research works printed but not linked: 5
- Scranton A, Bowman C, Peiffer R, eds. ACS Symposium Series 673; American Chemical Society, Washington DC. pp 189-202.
- Ratner BD, Hoffman AS, Schoen FJ, Lemon JE, eds. Aca- demic Press, San Diego. pp 65-73.
- Lamba NMK, Woodhouse KA, Cooper SL (1998) Poly- urethanes in Biomedical Applications. CRC Press: New York p 205-241.
- Mark JE, Alcock HR, West R (1992) Inorganic Poly- mers. Prentice Hall, Upper Saddle River, NJ. Chapter
- Ng SY, Vandamme T, Tayler MS, Heller J (1997) Syn- thesis and erosion studies of self-catalysed poly(orthoester)s. Macromolecules 30: 770-772.
Cited by
Items 101–200 of 1,762
Biodegradable Polymers for Biomedical Additive Manufacturing
Puppi, D., & Chiellini, F. (2020) · Applied Materials Today · doi:10.1016/j.apmt.2020.100700 · Cited by 191
Mesenchymal stem cells cultured on a collagen scaffold: In vitro osteogenic differentiation
Donzelli, E., Salvadè, A., Mimo, P., Viganò, M., Morrone, M., Papagna, R., Carini, F., Zaopo, A., Miloso, M., Baldoni, M., et al. (2007) · Archives of Oral Biology · doi:10.1016/j.archoralbio.2006.07.007 · Cited by 191
Silk as a potential candidate for bone tissue engineering
Mottaghitalab, F., Hosseinkhani, H., Shokrgozar, M. A., Mao, C., Yang, M., & Farokhi, M. (2015) · Journal of Controlled Release · doi:10.1016/j.jconrel.2015.07.031 · Cited by 190
Barrioni, B. R., de Carvalho, S. M., Oréfice, R. L., de Oliveira, A. A. R., & Pereira, M. D. M. (2015) · Materials Science and Engineering: C · doi:10.1016/j.msec.2015.03.027 · Cited by 189
Bone Tissue Engineering via Carbon‐Based Nanomaterials
Peng, Z., Zhao, T., Zhou, Y., Li, S., Li, J., & Leblanc, R. M. (2020) · Advanced Healthcare Materials · doi:10.1002/adhm.201901495 · Cited by 187
Cui, Y., Liu, Y., Cui, Y., Jing, X., Zhang, P., & Chen, X. (2009) · Acta Biomaterialia · doi:10.1016/j.actbio.2009.03.024 · Cited by 186
Biomedical polymers: synthesis, properties, and applications
Chen, W.-H., Chen, Q.-W., Chen, Q., Cui, C., Duan, S., Kang, Y., Liu, Y., Liu, Y., Muhammad, W., Shao, S., et al. (2022) · Science China Chemistry · doi:10.1007/s11426-022-1243-5 · Cited by 187
Nejati, E., Mirzadeh, H., & Zandi, M. (2008) · Composites Part A: Applied Science and Manufacturing · doi:10.1016/j.compositesa.2008.05.018 · Cited by 186
Germaini, M.-M., Belhabib, S., Guessasma, S., Deterre, R., Corre, P., & Weiss, P. (2022) · Progress in Materials Science · doi:10.1016/j.pmatsci.2022.100963 · Cited by 184
Degradation of poly-L-lactide. Part 1: in vitro and in vivo physiological temperature degradation
Weir, N. A., Buchanan, F. J., Orr, J. F., & Dickson, G. R. (2004) · Proceedings of the Institution of Mechanical Engineers, Part H: Journal of Engineering in Medicine · doi:10.1243/0954411041932782 · Cited by 182
Applying the Principles of Green Chemistry to Polymer Production Technology
Dubé, M. A., & Salehpour, S. (2014) · Macromolecular Reaction Engineering · doi:10.1002/mren.201300103 · Cited by 180
Kemala, T., Budianto, E., & Soegiyono, B. (2012) · Arabian Journal of Chemistry · doi:10.1016/j.arabjc.2010.08.003 · Cited by 178
Review of Multifarious Applications of Poly (Lactic Acid)
Chen, Y., Geever, L. M., Killion, J. A., Lyons, J. G., Higginbotham, C. L., & Devine, D. M. (2016) · Polymer-Plastics Technology and Engineering · doi:10.1080/03602559.2015.1132465 · Cited by 178
“to suit various applications, and the ability to fabricate into various shapes with desired pore morphologic features([108,122]).”
BackgroundPorous bone tissue scaffold concept based on shape memory PLA/Fe3O4
Zhao, W., Huang, Z., Liu, L., Wang, W., Leng, J., & Liu, Y. (2021) · Composites Science and Technology · doi:10.1016/j.compscitech.2020.108563 · Cited by 178
Zhang, H., Lin, C.-Y., & Hollister, S. J. (2009) · Biomaterials · doi:10.1016/j.biomaterials.2009.04.015 · Cited by 174
“The synthetic, biodegradable poly(3-caprolactone) (PCL) has received considerable attention for tissue engineering, especially for bone and cartilage regeneration since it has appropriate mechanical properties, is less expensive and is easily fabricated into complicated shapes with appropriate porosity [2–4].”
Figueira, D. R., Miguel, S. P., de Sá, K. D., & Correia, I. J. (2016) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2016.09.080 · Cited by 171
The use of mesenchymal stem cells in tissue engineering: A global assessment
Rosenbaum, A. J., Grande, D. A., & Dines, J. S. (2008) · Organogenesis · doi:10.4161/org.6048 · Cited by 170
Xie, H., Cao, T., Rodríguez-Lozano, F. J., Luong-Van, E. K., & Rosa, V. (2017) · Dental Materials · doi:10.1016/j.dental.2017.04.008 · Cited by 170
“Due to the enhanced capabilities, composites are widely used in dentistry and other biomedical areas as restorative materials, drug carriers, prosthetic parts and others [1,2].”
BackgroundOrganic Bioelectronics: Materials and Biocompatibility
Feron, K., Lim, R., Sherwood, C., Keynes, A., Brichta, A., & Dastoor, P. C. (2018) · International Journal of Molecular Sciences · doi:10.3390/ijms19082382 · Cited by 169
“One approach involves fabricating scaffolds that promote cell growth in a 3D environment and there are a number of excellent reviews on passive materials for 3D support structures [59,60].”
BackgroundSaroia, J., Yanen, W., Wei, Q., Zhang, K., Lu, T., & Zhang, B. (2018) · Bio-Design and Manufacturing · doi:10.1007/s42242-018-0029-7 · Cited by 170
“However, the prominent advantages of synthetic polymers are comparatively high degradation and mechanical properties [74] with simple structure and monomeric unit constituency [75].”
BackgroundInfluentialCyclic polyesters: synthetic approaches and potential applications
Hoskins, J. N., & Grayson, S. M. (2011) · Polym. Chem. · doi:10.1039/c0py00102c · Cited by 166
Citric acid-derived in situ crosslinkable biodegradable polymers for cell delivery
Gyawali, D., Nair, P., Zhang, Y., Tran, R. T., Zhang, C., Samchukov, M., Makarov, M., Kim, H. K. W., & Yang, J. (2010) · Biomaterials · doi:10.1016/j.biomaterials.2010.08.022 · Cited by 166
In Vivo Applications of Electrospun Tissue-Engineered Vascular Grafts: A Review
Rocco, K. A., Maxfield, M. W., Best, C. A., Dean, E. W., & Breuer, C. K. (2014) · Tissue Engineering Part B: Reviews · doi:10.1089/ten.teb.2014.0123 · Cited by 165
“…polyester in vivo , the degradation process takes anywhere from weeks for hydrophilic PGA to years for high-molecular-weight hydrophobic PCL. 45 Combining these materials as blends with biopolymers such as collagen or as copolymers such as poly( l -lactic acid-co -glycolic acid) (PLGA) and…”
InfluentialSolvent induced phase inversion-based in situ forming controlled release drug delivery implants
Thakur, R. R. S., McMillan, H. L., & Jones, D. S. (2014) · Journal of Controlled Release · doi:10.1016/j.jconrel.2013.12.020 · Cited by 165
Patterning Methods for Polymers in Cell and Tissue Engineering
Kim, H. N., Kang, D.-H., Kim, M. S., Jiao, A., Kim, D.-H., & Suh, K.-Y. (2012) · Annals of Biomedical Engineering · doi:10.1007/s10439-012-0510-y · Cited by 165
Innovative Biomaterials for Bone Regrowth
Iaquinta, M. R., Mazzoni, E., Manfrini, M., D’Agostino, A., Trevisiol, L., Nocini, R., Trombelli, L., Barbanti-Brodano, G., Martini, F., & Tognon, M. (2019) · International Journal of Molecular Sciences · doi:10.3390/ijms20030618 · Cited by 165
“PCL is an aliphatic polyester biomaterial, which was approved by the FDA since it is multiform and highly biocompatible [101].”
BackgroundJo, J., Lee, E., Shin, D., Kim, H., Kim, H., Koh, Y., & Jang, J. (2009) · Journal of Biomedical Materials Research Part B: Applied Biomaterials · doi:10.1002/jbm.b.31392 · Cited by 163
“Biodegradable synthetic polymers, such as poly(glycolic acid), poly(lactic acid), poly(e-caprolactone) (PCL), and their copolymers, have been widely used as the matrices in these composites, because they have favorable biocompatibility and degradability.(4) Among these polymers, PCL is a common biodegradable, FDA-appr…”
BackgroundBiodegradable polymer nanocomposites for ligament/tendon tissue engineering
Silva, M., Ferreira, F. N., Alves, N. M., & Paiva, M. C. (2020) · Journal of Nanobiotechnology · doi:10.1186/s12951-019-0556-1 · Cited by 163
“The specific use of biodegradable polymer matrices for the production of the nanocomposites offers great advantages and include the ability to tailor mechanical properties and degradation kinetics to suit various applications [96].”
BackgroundBiomaterials for Craniofacial Bone Regeneration
Thrivikraman, G., Athirasala, A., Twohig, C., Boda, S. K., & Bertassoni, L. E. (2017) · Dental Clinics of North America · doi:10.1016/j.cden.2017.06.003 · Cited by 159
“Furthermore, their hydrophobic nature is not conducive to cell attachment, and the absence of functional groups results in inferior osteoinduction [73].”
BackgroundInfluentialSynthesis of two-component injectable polyurethanes for bone tissue engineering
Bonzani, I. C., Adhikari, R., Houshyar, S., Mayadunne, R., Gunatillake, P., & Stevens, M. M. (2007) · Biomaterials · doi:10.1016/j.biomaterials.2006.08.026 · Cited by 159
“The mechanical properties, degradation times, and chemical functionalities of synthetic polymers can be easily tailored to support the tissue type, providing issues such as cytocompatibility, sterilisation, and ease of handling are addressed [3].”
BackgroundSelf-citationNaturally-Derived Biomaterials for Tissue Engineering Applications
Brovold, M., Almeida, J. I., Pla-Palacín, I., Sainz-Arnal, P., Sánchez-Romero, N., Rivas, J. J., Almeida, H., Dachary, P. R., Serrano-Aulló, T., Soker, S., et al. (2018) · Advances in Experimental Medicine and Biology · doi:10.1007/978-981-13-0947-2_23 · Cited by 160
“Depending on the final use, they usually share several prominent features: biocompatibility, biodegradability, and nontoxicity, amongst others [7].”
BackgroundDirect micro-patterning of biodegradable polymers using ultraviolet and femtosecond lasers
Aguilar, C. A., Lu, Y., Mao, S. S., & Chen, S. (2005) · Biomaterials · doi:10.1016/j.biomaterials.2005.04.053 · Cited by 172
“Our results demonstrate that both lasers are excellent tools for micro-patterning biodegradable polymers since the bulk properties of the material can remain intact and because the direct-write method is rapid, flexible, and a chemical-free process. r 2005 Elsevier Ltd.”
BackgroundBioactive and Biodegradable Nanocomposites and Hybrid Biomaterials for Bone Regeneration
Allo, B. A., Costa, D. O., Dixon, S. J., Mequanint, K., & Rizkalla, A. S. (2012) · Journal of Functional Biomaterials · doi:10.3390/jfb3020432 · Cited by 164
Knowledge‐Based Approach towards Hydrolytic Degradation of Polymer‐Based Biomaterials
Hofmann, D., Entrialgo‐Castaño, M., Kratz, K., & Lendlein, A. (2009) · Advanced Materials · doi:10.1002/adma.200802213 · Cited by 154
Lithography-based methods to manufacture biomaterials at small scales
Tran, K. T. M., & Nguyen, T. D. (2016) · Journal of Science Advanced Materials and Devices · doi:10.1016/j.jsamd.2016.12.001 · Cited by 181
Cooper, K. (2001) · CRC Press eBooks · doi:10.1201/9780203910795 · Cited by 160
Bioerodible polyphosphazenes and their medical potential
Allcock, H. R., & Morozowich, N. L. (2012) · Polym. Chem. · doi:10.1039/c1py00468a · Cited by 152
Polymeric Biomaterials for Scaffold-Based Bone Regenerative Engineering
Ogueri, K. S., Jafari, T., Ivirico, J. L. E., & Laurencin, C. T. (2018) · Regenerative Engineering and Translational Medicine · doi:10.1007/s40883-018-0072-0 · Cited by 168
“In contrast, the degradation time of the polyesters with reasonably short aliphatic chains between ester linkages matches the time frame for most biomedical applications [2].”
InfluentialAlizadeh-Osgouei, M., Li, Y., Vahid, A., Ataee, A., & Wen, C. (2020) · Smart Materials in Medicine · doi:10.1016/j.smaim.2020.10.003 · Cited by 154
Development of polyurethanes for bone repair
Marzec, M., Kucińska‐Lipka, J., Kalaszczyńska, I., & Janik, H. (2017) · Materials Science and Engineering C · doi:10.1016/j.msec.2017.07.047 · Cited by 154
Breathing life into engineered tissues using oxygen-releasing biomaterials
Suvarnapathaki, S., Wu, X., Lantigua, D., Nguyen, M. A., & Camci-Unal, G. (2019) · NPG Asia Materials · doi:10.1038/s41427-019-0166-2 · Cited by 150
Cell culture in autologous fibrin scaffolds for applications in tissue engineering
de la Puente, P., & Ludeña, D. (2014) · Experimental Cell Research · doi:10.1016/j.yexcr.2013.12.017 · Cited by 165
Molavi, F., Barzegar-Jalali, M., & Hamishehkar, H. (2020) · Journal of Controlled Release · doi:10.1016/j.jconrel.2020.01.028 · Cited by 154
“Furthermore, possible side effects such as immunogenicity, poisonousness and even infections are least for the pure synthetic polymers with identical monomeric units [24,25].”
BackgroundNaderi‐Meshkin, H., Andreas, K., Matin, M. M., Sittinger, M., Bidkhori, H. R., Ahmadiankia, N., Bahrami, A. R., & Ringe, J. (2013) · Cell Biology International · doi:10.1002/cbin.10181 · Cited by 156
“Our results were consistent with other reports (Hannouche et al., 2007; Kurdi et al., 2010) indicating that CH-GP-HEC hydrogels are stable in solution and keep their structural integrity for 4 weeks in vitro.”
BackgroundResultInfluentialRNA interference by nanofiber-based siRNA delivery system
Cao, H., Jiang, X., Chai, C., & Chew, S. Y. (2010) · Journal of Controlled Release · doi:10.1016/j.jconrel.2010.02.003 · Cited by 144
“PCL is a biocompatible polymer with a low degradation rate suitable for long-term tissue engineering applications [30].”
BackgroundBiodegradable Nanopolymers in Cardiac Tissue Engineering: From Concept Towards Nanomedicine
Mohammadi Nasr, S., Rabiee, N., Hajebi, S., Ahmadi, S., Fatahi, Y., Hosseini, M., Bagherzadeh, M., Ghadiri, A. M., Rabiee, M., Jajarmi, V., et al. (2020) · International Journal of Nanomedicine · doi:10.2147/ijn.s245936 · Cited by 143
Nejati, E., Firouzdor, V., Eslaminejad, M. B., & Bagheri, F. (2008) · Materials Science and Engineering C · doi:10.1016/j.msec.2008.07.038 · Cited by 141
Shie, M., Chang, W., Wei, L.-J., Huang, Y., Chen, C.-H., Shih, C., Chen, Y., & Shen, Y. (2017) · Materials · doi:10.3390/ma10020136 · Cited by 147
“However, the physical properties of these materials are not very similar with living tissues and some of these materials often need to be dissolved by highly toxic solvents [25,26].”
Tripathi, A., Kathuria, N., & Kumar, A. (2008) · Journal of Biomedical Materials Research Part A · doi:10.1002/jbm.a.32127 · Cited by 144
Lee, H., Yang, G. H., Kim, M., Lee, J., Huh, J., & Kim, G. (2017) · Materials Science and Engineering C · doi:10.1016/j.msec.2017.11.013 · Cited by 140
Concise Review: Workshop Review: Understanding and Assessing the Risks of Stem Cell-Based Therapies
Heslop, J. A., Hammond, T. G., Santeramo, I., Tort Piella, A., Hopp, I., Zhou, J., Baty, R., Graziano, E. I., Proto Marco, B., Caron, A., et al. (2015) · Stem Cells Translational Medicine · doi:10.5966/sctm.2014-0110 · Cited by 139
Hydrophilization of synthetic biodegradable polymer scaffolds for improved cell/tissue compatibility
Oh, S. H., & Lee, J. H. (2013) · Biomedical Materials · doi:10.1088/1748-6041/8/1/014101 · Cited by 145
“More details on the biodegradable polymers are well described in several literatures [24, 27, 31, 40].”
BackgroundZheng, Z., Tan, Y., Li, Y., Liu, Y., Yi, G., Yu, C., & Wei, H. (2021) · Journal of Controlled Release · doi:10.1016/j.jconrel.2021.05.023 · Cited by 145
Advancement of Biomaterial-Based Postoperative Adhesion Barriers
Chandel, A. K. S., Shimizu, A., Hasegawa, K., & Ito, T. (2021) · Macromolecular Bioscience · doi:10.1002/mabi.202000395 · Cited by 138
Badhe, R. V., Bijukumar, D. R., Chejara, D. R., Mabrouk, M., Choonara, Y. E., Kumar, P., du Toit, L. C., Kondiah, P. P. D., & Pillay, V. (2016) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2016.09.095 · Cited by 139
Synthetic Polymers for Organ 3D Printing
Liu, F., & Wang, X. (2020) · Polymers · doi:10.3390/polym12081765 · Cited by 154
“3D printing of PLGA, with a glass transition temperature of 45–50 ◦C and melting temperature of >120 ◦C, has proven to be challenging at a higher extrusion temperature [51,52].”
BackgroundDeng, M., Kumbar, S. G., Wan, Y., Toti, U. S., Allcock, H. R., & Laurencin, C. T. (2010) · Soft Matter · doi:10.1039/b926402g · Cited by 136
Manchanda, R., Fernandez-Fernandez, A., Nagesetti, A., & McGoron, A. J. (2009) · Colloids and Surfaces B Biointerfaces · doi:10.1016/j.colsurfb.2009.08.043 · Cited by 140
Biodegradable core-shell electrospun nanofibers based on PLA and γ-PGA for wound healing
Fang, Y., Zhu, X., Wang, N., Zhang, X., Yang, D., Nie, J., & Ma, G. (2019) · European Polymer Journal · doi:10.1016/j.eurpolymj.2019.03.050 · Cited by 135
Development of bone substitute materials: from ‘biocompatible’ to ‘instructive’
Bongio, M., van den Beucken, J. J. J. P., Leeuwenburgh, S. C. G., & Jansen, J. A. (2010) · Journal of Materials Chemistry · doi:10.1039/c0jm00795a · Cited by 136
Park, S. H., Park, D. S., Shin, J. W., Kang, Y. G., Kim, H. K., Yoon, T. R., & Shin, J. (2012) · Journal of Materials Science Materials in Medicine · doi:10.1007/s10856-012-4738-8 · Cited by 146
Li, D., Sun, H., Jiang, L., Zhang, K., Liu, W., Zhu, Y., Fangteng, J., Shi, C., Zhao, L., Sun, H., et al. (2014) · ACS Applied Materials & Interfaces · doi:10.1021/am5017792 · Cited by 134
Processing Techniques and Applications of Silk Hydrogels in Bioengineering
Floren, M., Migliaresi, C., & Motta, A. (2016) · Journal of Functional Biomaterials · doi:10.3390/jfb7030026 · Cited by 134
“Specifically, synthetic polymers are attractive because they can be fabricated into various shapes with desired morphologies and features that can be permissive for cell maintenance and in-growth [3].”
BackgroundYang, J. H., An, X., Liu, L., Tang, S., Cao, H., Xu, Q., & Liu, H. (2020) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2020.116881 · Cited by 138
Recent advancements in nanomaterials for biomedical implants
Gautam, S., Bhatnagar, D., Bansal, D., Batra, H., & Goyal, N. (2022) · Biomedical Engineering Advances · doi:10.1016/j.bea.2022.100029 · Cited by 152
Tawiah, B., Yu, B., Yuen, R. K. K., Hu, Y. Z., Wei, R., Xin, J. H., & Fei, B. (2019) · Carbon · doi:10.1016/j.carbon.2019.05.002 · Cited by 128
Polycaprolactone-based materials in wound healing applications
Raina, N., Pahwa, R., Khosla, J. K., Gupta, P. N., & Gupta, M. (2021) · Polymer Bulletin · doi:10.1007/s00289-021-03865-w · Cited by 148
Biodegradable Polymers in Bone Tissue Engineering
Kroeze, R. J., Helder, M. N., Govaert, L. E., & Smit, T. H. (2009) · Materials · doi:10.3390/ma2030833 · Cited by 135
“Some excellent reviews have discussed the various types of degradable polymers and their copolymers [22-29].”
Silk nanoparticles: from inert supports to bioactive natural carriers for drug delivery
Crivelli, B., Perteghella, S., Bari, E., Sorrenti, M., Tripodo, G., Chlapanidas, T., & Torre, M. L. (2017) · Soft Matter · doi:10.1039/c7sm01631j · Cited by 134
“SF is universally recognized as a biocompatible material, its tolerability is comparable to that observed for synthetic materials (PLA, PGA and PLGA).”
Xia, H., Zhao, D., Zhu, H., Hua, Y., Xiao, K., Xu, Y., Liu, Y., Chen, W., Liu, Y., Zhang, W., et al. (2018) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.8b10926 · Cited by 140
Poly (∊-caprolactone) Fiber: An Overview
Azimi, B., Nourpanah, P., Rabiee, M., & Arbab, S. (2014) · Journal of Engineered Fibers and Fabrics · doi:10.1177/155892501400900309 · Cited by 131
“The homopolymer PCL has a total degradation of two to four years (depending of the starting molecular weight of the device or implant) [28-29].”
BackgroundPremature ovarian failure and tissue engineering
Ghahremani‐Nasab, M., Ghanbari, E., Jahanbani, Y., Mehdizadeh, A., & Yousefi, M. (2019) · Journal of Cellular Physiology · doi:10.1002/jcp.29376 · Cited by 127
“…biocompatibility, being highly porous for cells communication, nutrients delivery and oxygen exchange, and easy and inexpensive to be manufactured (Gunatillake & Adhikari, 2003; Hutmacher, 2000; Hutmacher et al., 2001; Mahla, 2016; Mano et al., 2007; Mikos, McIntire, Anderson, & Babensee, 1998;…”
BackgroundOsteochondral Tissue Engineering with Biphasic Scaffold: Current Strategies and Techniques
Shimomura, K., Moriguchi, Y., Murawski, C. D., Yoshikawa, H., & Nakamura, N. (2014) · Tissue Engineering Part B Reviews · doi:10.1089/ten.teb.2013.0543 · Cited by 143
“74 Synthetic polymers are also attractive, because they can be fabricated into various shapes with a desired pore according to the speed of cell migration or tissue in-growth.”
In vitro engineering of human ear-shaped cartilage assisted with CAD/CAM technology
Liu, Y., Zhang, L., Zhou, G., Li, Q., Liu, W., Yu, Z., Luo, X., Jiang, T. X., Zhang, W., & Cao, Y. (2009) · Biomaterials · doi:10.1016/j.biomaterials.2009.11.080 · Cited by 129
Preparation and biodegradation of clay composites of PLA
Nieddu, E., Mazzucco, L., Gentile, P., Benkó, T., Balbo, V., Mandrile, R., & Ciardelli, G. (2009) · Reactive and Functional Polymers · doi:10.1016/j.reactfunctpolym.2009.03.002 · Cited by 124
Stimuli-Responsive Soft Untethered Grippers for Drug Delivery and Robotic Surgery
Ghosh, A., Yoon, C., Ongaro, F., Scheggi, S., Selaru, F. M., Misra, S., & Gracias, D. H. (2017) · Frontiers in Mechanical Engineering · doi:10.3389/fmech.2017.00007 · Cited by 132
“It should be noted that there are a number of soft biodegradable materials that have been developed, primarily for tissue engineering applications and these could be utilized in the synthesis of dissolvable soft robots (Hutmacher et al., 2001; Gunatillake and Adhikari, 2003).”
BackgroundRecent advances in 3D printing for wound healing: A systematic review
Tabriz, A. G., & Douroumis, D. (2022) · Journal of Drug Delivery Science and Technology · doi:10.1016/j.jddst.2022.103564 · Cited by 142
Physical properties and biocompatibility of chitosan/soy blended membranes
Silva, S. S., Santos, M. I., Coutinho, O. P., et al. (2005) · Journal of Materials Science Materials in Medicine · doi:10.1007/s10856-005-0534-z · Cited by 124
Bilgi, E., Bayır, E., Şendemir, A., & Hameş, E. E. (2016) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2016.02.052 · Cited by 129
Bioresorbable and degradable behaviors of PGA : Current state and future prospects
Low, Y. J., Andriyana, A., Ang, B. C., & Abidin, N. I. Z. (2020) · Polymer Engineering and Science · doi:10.1002/pen.25508 · Cited by 137
Lligadas, G., Ronda, J. C., Galià, M., & Cádiz, V. (2007) · Biomacromolecules · doi:10.1021/bm060977h · Cited by 136
Scaffolds in regenerative endodontics: A review
Raghavendra, S., & Gathani, K. M. (2016) · Dental Research Journal · doi:10.4103/1735-3327.192266 · Cited by 125
“[3] Synthetic polymers are generally degraded by simple hydrolysis, whe natural polymers are mainly degraded enzymatically.[56]”
BackgroundAdvantages of biopolymers over synthetic polymers
Gowthaman, N. S. K., Lim, . N., Sreeraj, T. R., Amalraj, A., & Gopi, S. (2020) · Elsevier eBooks · doi:10.1016/b978-0-12-819240-5.00015-8 · Cited by 190
In vitro evaluation of electrospun PCL/nanoclay composite scaffold for bone tissue engineering
Ganesh, N., Thrivikraman, G., Mony, U., Chennazhi, K. P., & Nair, S. V. (2012) · Journal of Materials Science Materials in Medicine · doi:10.1007/s10856-012-4647-x · Cited by 121
Raftery, R. M., Walsh, D. P., Castaño, I. M., Heise, A., Duffy, G. P., Cryan, S., & O’Brien, F. J. (2016) · Advanced Materials · doi:10.1002/adma.201505088 · Cited by 128
Silk fibroin-based biomaterials for musculoskeletal tissue engineering
Ma, D., Wang, Y., & Dai, W. (2018) · Materials Science and Engineering: C · doi:10.1016/j.msec.2018.04.062 · Cited by 121
Design concepts and strategies for tissue engineering scaffolds
Chung, S., & King, M. W. (2011) · Biotechnology and Applied Biochemistry · doi:10.1002/bab.60 · Cited by 127
Wang, Z., Yu, L., Ding, M., Tan, H., Li, J., & Fu, Q. (2011) · Polym. Chem. · doi:10.1039/c0py00235f · Cited by 119
Kumar, A., Nune, K. C., Murr, L. E., & Misra, R. D. K. (2016) · International Materials Reviews · doi:10.1080/09506608.2015.1128310 · Cited by 129
Valderrama, M. A. M., van Putten, R., & Gruter, G. M. (2019) · European Polymer Journal · doi:10.1016/j.eurpolymj.2019.07.036 · Cited by 137
Physically transient electronic materials and devices
Shim, J., Rogers, J. A., & Kang, S. (2021) · Materials Science and Engineering R Reports · doi:10.1016/j.mser.2021.100624 · Cited by 130
Carbon nanotube-reinforced polymer nanocomposites for sustainable biomedical applications: A review
Abubakre, O. K., Medupin, R. O., Akintunde, I. B., et al. (2023) · Journal of Science Advanced Materials and Devices · doi:10.1016/j.jsamd.2023.100557 · Cited by 119
An Overview of Nano‐Polymers for Orthopedic Applications
Balasundaram, G., & Webster, T. J. (2007) · Macromolecular Bioscience · doi:10.1002/mabi.200600270 · Cited by 118
Polymers, Drug Release, and Drug‐Eluting Stents
COMMANDEUR, S., VAN BEUSEKOM, H. M. M., & VAN DER GIESSEN, W. J. (2006) · Journal of Interventional Cardiology · doi:10.1111/j.1540-8183.2006.00198.x · Cited by 118
Tissue engineered scaffolds in regenerative medicine.
Hosseinkhani, M., Mehrabani, D., Karimfar, M. H., Bakhtiyari, S., Manafi, A., & Shirazi, R. (2014) · PubMed Central · Cited by 122
Cabrera, M. S., Sanders, B., Goor, O. J. G. M., Driessen-Mol, A., Oomens, C. W. J., & Baaijens, F. P. T. (2017) · 3D Printing and Additive Manufacturing · doi:10.1089/3dp.2016.0052 · Cited by 117
“The speed at which hydrolysis of polyesters occurs in vivo depends on multiple factors, such as monomer composition, relative humidity, temperature, and bioactivity of present enzymes.(23) Besides hydrolytic degradation, oxidative and enzymatic degradation also contributes to in vivo polymer degradation.”
Chong, W. J., Shen, S., Li, Y., Trinchi, A., Pejak Simunec, D., Kyratzis, I. (., Sola, A., & Wen, C. (2023) · Smart Materials in Manufacturing · doi:10.1016/j.smmf.2022.100004 · Cited by 78
Tamjid, E., Bagheri, R., Vossoughi, M., & Simchi, A. (2011) · Materials Science and Engineering C · doi:10.1016/j.msec.2011.06.013 · Cited by 117
Silk fibroin/hydroxyapatite scaffold: a highly compatible material for bone regeneration
Saleem, M., Rasheed, S., & Yougen, C. (2020) · Science and Technology of Advanced Materials · doi:10.1080/14686996.2020.1748520 · Cited by 111
“slower degradation rate than many other biomaterials [35,36], though it is considered as non-degradable biomaterial according to US Pharmacopeia’s defini-”
BackgroundVoronov, R. S., VanGordon, S. B., Sikavitsas, V. I., & Papavassiliou, D. V. (2010) · Journal of Biomechanics · doi:10.1016/j.jbiomech.2010.01.007 · Cited by 118
“Poly-L-lactic acid (PLLA) scaffolds prepared via solvent casting/ particulate leaching are among the most popular and widely used synthetic polymeric materials in bone tissue engineering (Hutmacher, 2000; Gunatillake and Adhikari, 2003; Liu and Ma, 2004; Bronzino, 2006; Holland and Mikos, 2006).”
Method
Metadata
- Authors
- CSIRO Molecular Science, B. 1., & Gunatillake, P.
- Corresponding author
- CSIRO Molecular Science, Bag 10, Clayton South MDC, Vic 3169, Australia
- Venue
- European Cells and Materials
- Publisher
- Forum Multimedia Publishing LLC
- Published
- 2003-10-01
- Volume
- 5
- Pages
- 1-16
- ISSN
- 1473-2262 (ISSN-L)
- OpenAlex
- W2106035984
- Cited by
- 1,765
- References
- 97
- Citations by year
- 2026: 43 · 2025: 61 · 2024: 59 · 2023: 80 · 2022: 90 · 2021: 112 · 2020: 102 · 2019: 115 · 2018: 105 · 2017: 128 · 2016: 110 · 2015: 106 · 2014: 110 · 2013: 91 · 2012: 86
- FWCI
- 1.32
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- cc-by
- Locations
- European Cells and Materials (publishedVersion, cc-by)
- PubMed (publishedVersion)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion)
- Topics
- Physical Sciences › Materials Science › Biomaterials › biodegradable polymer synthesis and properties
- Physical Sciences › Engineering › Biomedical Engineering › Bone Tissue Engineering Materials
- Health Sciences › Medicine › Surgery › Surgical Sutures and Adhesives
- Keywords
- tissue engineering, polyesters, polyglycolic acid, polylactic acid, polyanhydrides, polyphosphazenes, polyurethane, poly(propylene fumarate), injectable polymers, orthopedic tissue engineering, biodegradation, biocompatibility, degradation products
- MeSH terms
- Biocompatible Materials, Models, Chemical, Polymers, Tissue Engineering
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.